XYLANTRAP-13-MIB
File:
XYLANTRAP-13-MIB.mib (37058 bytes)
Imported modules
Imported symbols
Defined Values
tempAlarm13 |
1 |
A tempAlarm indicates a temperature sensor has changed
its state from underThreshold(4) to overThreshold(3). |
TRAP-TYPE |
|
|
|
moduleChange13 |
2 |
A moduleChange trap occurs when a module is inserted or
removed from the chassis. |
TRAP-TYPE |
|
|
|
powerEvent13 |
3 |
A powerEvent trap occurs when a power supply is inserted or
removed from the chassis, or a problem condition is
recognized on a power supply. |
TRAP-TYPE |
|
|
|
controllerEvent13 |
4 |
A controlEvent trap occurs when a chassis controller (MPM)
loses or gains the state of master(3). If this is due to
chassis controller being inserted or removed from the slot,
a moduleChange trap will also be sent. |
TRAP-TYPE |
|
|
|
loginViolation13 |
5 |
A loginViolation trap occurs when a login attempt fails
due to an incorrect login-id or password. |
TRAP-TYPE |
|
|
|
macVlanViolation13 |
6 |
A macVlanViolation trap occurs when a frame is received from
a port with a VLAN ID different from the VLAN where the
frame previously has received. |
TRAP-TYPE |
|
|
|
macDuplicatePort13 |
7 |
A macDuplicatePort trap occurs when a frame is received from
a source port different from the port where the frame previously
has received although they both ports belong to the same VLAN. |
TRAP-TYPE |
|
|
|
portLinkUpEvent13 |
8 |
A portLinkTrap occurs whenever a phy, log, or virt port
is enabled. |
TRAP-TYPE |
|
|
|
portLinkDownEvent13 |
9 |
A portLinkTrap occurs whenever a phy, log, or virt port
is disabled. |
TRAP-TYPE |
|
|
|
portPartitioned13 |
10 |
A portPartioned trap occurs when the physical port
has transitioned thru enable/disable states faster
than 10 times in the past second...indicative of a
flakey cable. |
TRAP-TYPE |
|
|
|
portRecordMismatch13 |
11 |
A portRecordMismatch trap occurs when the specified
port data is found to be diferent than the privious
configuration. Typically this will be generated when
a NIC of one type is swapped out for a DIFFERENT type.
IE ethernet for fddi, atm for token-ring, etc... |
TRAP-TYPE |
|
|
|
groupChange13 |
14 |
A groupChange trap occurs whenever a group is
created or deleted from the system via the UI
or SNMP. The group and status code are sent as
part of the variable binding.
The status codes are:
1 - disable
2 - enable
3 - delete
4 - create
5 - modify (see xylan-vport MIB) |
TRAP-TYPE |
|
|
|
vlanChange13 |
15 |
A vlanChange trap occurs whenever a VLAN is
created or deleted from the system via the UI
or SNMP. The group, vlan and status code are sent as
part of the variable binding. See groupChange for
the status codes. |
TRAP-TYPE |
|
|
|
portMove13 |
16 |
A portMove trap occurs when the specified
port is moved from a group/vlan or has had
its configuration changed. |
TRAP-TYPE |
|
|
|
moduleResetReload13 |
17 |
A moduleResetReload trap occurs when the specified
module has been reset or reloaded by the chassis mgr. |
TRAP-TYPE |
|
|
|
systemEvent13 |
18 |
A systemEvent trap occurs when a potentially
fatal system error occurrs. Such as: out of FLASH/
memory space. The event type is in the var bind.
A Descriptive string MAY be present. The following
trap numbers are defined (see xylan-trapc.mib):
10 Unspecified log event
11 Log file full
12 Log file erased
20 Unspecified memory event
21 Memory shortage
30 Unsepcified CPU event
31 Long term CPU overload
32 Short term CPU overload
40 Unspecified ffs event
41 Attempt to write to full ffs
42 System/user directed purge
43 Removed imgs/cfgs
44 Exec file removed
45 Config file removed
46 Exec file updated
47 Config file updated
50 Unspecified chassis event
51 Module failed to init
52 Module failed to load
53 Module startup failed
54 Module failed
55 Driver failed |
TRAP-TYPE |
|
|
|
vlanRouteTableFull13 |
19 |
A vlanRouteTableFull trap occurs when either the
IP or IPX route table is full. (discovered on
insertion attempt) |
TRAP-TYPE |
|
|
|
sapTableFull13 |
20 |
A sapTableFull trap occurs when the IPX SAP
table is found to be full on insertion. |
TRAP-TYPE |
|
|
|
atmSSCOPstate13 |
21 |
A atmSSCOPstate trap occurs when the signalling
state for the specified physical port changes. |
TRAP-TYPE |
|
|
|
ilmiState13 |
22 |
A ilmiState trap occurs when the ILMI state for
the specified physical port changes. |
TRAP-TYPE |
|
|
|
atmConnection13 |
23 |
A atmConnection trap occurs when the specified
ATM Vcc is created or deleted. |
TRAP-TYPE |
|
|
|
atmService13 |
24 |
A atmService trap occurs when the specified
ATM service is created or deleted> |
TRAP-TYPE |
|
|
|
dlciNew13 |
27 |
Frame-Relay Dlci Just Created |
TRAP-TYPE |
|
|
|
dlciDel13 |
28 |
Frame-Relay Dlci Just Deleted |
TRAP-TYPE |
|
|
|
dlciUp13 |
29 |
Frame-Relay Dlci Just Changed to Active |
TRAP-TYPE |
|
|
|
dlciDn13 |
30 |
Frame-Relay Dlci Just Changed to InActive |
TRAP-TYPE |
|
|
|
portManualForwardingMode13 |
31 |
A portManualForwardingMode trap occurs when the specified
port is placed into manual mode forwarding as its default
setting whenever the port is assigned to a Group that is
participating in the IBM spanning tree algorithm. |
TRAP-TYPE |
|
|
|
fddiCFStateChange13 |
32 |
A fddiCFStateChange trap occurs when the specified
fddi physical port changes from wrap configuration state. |
TRAP-TYPE |
|
|
|
duplicateIPaddress13 |
35 |
A duplicateIPaddress trap occurs whenever the switch
detects a duplicate IP address. |
TRAP-TYPE |
|
|
|
duplicateMACaddress13 |
36 |
A duplicateMACaddress trap occurs whenever the switch
detects a duplicate MAC address of one of its own
router ports. |
TRAP-TYPE |
|
|
|
healthThresholdRising13 |
37 |
A healthThresholdRising trap occurs when at least
one of the user-specified thresholds is exceeded
for the first time. |
TRAP-TYPE |
|
|
|
healthThresholdFalling13 |
38 |
A healthThresholdFalling trap occurs when at least
one of the user-specified thresholds was exceeded
during the previous cycle and none of them are exceeded
this cycle. |
TRAP-TYPE |
|
|
|
healthThresholdDevice13 |
39 |
A healthThresholdDevice trap occurs when at least
one device-level threshold crossing is detected. |
TRAP-TYPE |
|
|
|
healthThresholdModule13 |
40 |
A healthThresholdModule trap occurs when at least
one module-level threshold crossing is detected. |
TRAP-TYPE |
|
|
|
healthThresholdPort13 |
63 |
A healthThresholdPort trap occurs when at least
one port-level threshold crossing is detected. |
TRAP-TYPE |
|
|
|
xylanXIPXMAPPortStatusChange13 |
41 |
A xylanXIPXMAPPortStatusChange trap occurs when a
change in status occurs in an XMAP-tracked virtual
port. |
TRAP-TYPE |
|
|
|
avlAuthAttempt13 |
43 |
The last Authenticated VLAN authentication attempt. |
TRAP-TYPE |
|
|
|
xylanXIPGMAPFailedUpdate13 |
44 |
A xylanXIPGMAPFailedUpdate trap occurs when GMAP is unable
to update the forwarding database to reflect information
in its internal database. |
TRAP-TYPE |
|
|
|
clkBusLineStateChange13 |
45 |
A clkBusLineStateChange trap occurs when 1 of the
following occurs at the 8k or the 19m bus line:
1) bus line's status changes (active or inactive)
2) clock switching has occured
The following are sent as part of the variable
binding:
Status code:
inactive - 1
active - 2
Bus line:
eightKhz - 1
nineteenMhz - 2 |
TRAP-TYPE |
|
|
|
bind-violation13 |
46 |
A bind-violation trap occurs whenever
a binding rule which has been configured gets violated. |
TRAP-TYPE |
|
|
|
phyPortPartition13 |
47 |
A phyPortPartition trap occurs when the device detects link
state is active for a physical port, but line errors,
or system behaviour, indicate that the cable/media is
unuseable. The device will then force the disabling of
the port in question and generate this trap.
The device will retry using the port in question should a
cable drop occur, which may indicate a user has attempted
to fix the bad media. |
TRAP-TYPE |
|
|
|
policyEvent13 |
48 |
This trap signifies that the switch subagent has
detected that the event represented by eventIndex has
occurred in the switch. |
TRAP-TYPE |
|
|
|
pnniRouteConflictPort13 |
50 |
This trap occurs when PNNI detects that a static
route on the pnnixIfPortId port has been created
and this port has been configured as a PNNI port.
This may cause mis-routing in a PNNI network if the
port turns out to be an Inside port. |
TRAP-TYPE |
|
|
|
pnniRouteConflictSamePG13 |
51 |
This trap occurs when PNNI detects that a static
route on the pnnixIfPortId port has been created
and this route matches (a prefix of) the Peer
Group ID. This may cause mis-routing in a PNNI
network. |
TRAP-TYPE |
|
|
|
xPnniFilterAlarm13 |
52 |
An alarm indicating that a PNNI filter has denied access
to a call attempt. The filter denying the access is
identified in the variable. |
TRAP-TYPE |
|
|
|
xPnniPmPThresholdReached13 |
53 |
An alarm indicating that no more Point-to-Multipoint calls
may be established until ongoing PMP calls are released due
to capacity restrictions of the local fabric. |
TRAP-TYPE |
|
|
|
xPnniDtlTableExhaustion13 |
54 |
An alarm indicating that no more calls may be established
due to capacity restrictions of the DTL Table. |
TRAP-TYPE |
|
|
|
xPnniNeighborFailure13 |
55 |
An alarm indicating that a neighbor on a particular port
has ceased communication with this switching system. |
TRAP-TYPE |
|
|
|
xPnniNodeDown13 |
56 |
An alarm indicating that a PNNI node (instance) within
this switching system has been disabled and the reason.
If the reason is due to remote action, the IP address
causing the action is specified in the trap. |
TRAP-TYPE |
|
|
|
xPnniLinkFailure13 |
57 |
An alarm indicating that a particular port has transitioned
from operational state within this switching system. |
TRAP-TYPE |
|
|
|
fddiLerFlagChange13 |
65 |
A fddiLerFlagChange trap occurs when the LER flag on a port
changes from CLEAR to SET. |
TRAP-TYPE |
|
|
|
fddiLCTFailCntIncr13 |
66 |
A fddiLCTFailCntIncr trap occurs when the LCT flag on a port
is incremented. |
TRAP-TYPE |
|
|
|
mpcStatisticsOverflow13 |
67 |
A statistic overflow trap occurs when a paticular entry of mpcStatisticsTable
reach the threshold value, the paticular statistics is identified by
statisticsNum of trap data which is the entry index of the mpcStatisticsTable.
The current threshold valye is hard coded to 2024.
The Trap PDU data format:
struct {
unsigned int mpcIndex; Index of MPC
unsigned int statisticsNum; Entry Index of mpcStatisticsTable
unsigned long statisticsThreshold; Trap Threshold Value of Entry
unsigned long statisticsValue; Current Statistics Value of Entry
}
where statisticsNum, statisticsThreshold and statisticsValue entry
attached with objecid mpcStatRxMpoaResolveReplyInsufECResources |
TRAP-TYPE |
|
|
|
mpcShortCut13 |
68 |
A shortcut trap occurs when the shortcut path established, closed or
failed to complete path.
event type: 01 shortcut established
02 shortcut closed
03 failed to complete path
The Trap PDU data format:
struct {
unsigned int event_type;
unsigned int vcNumber; VCI number of destination
unsigned int prototype; 1: IP, 11: IPX
unsigned char destNet_addr[10]; IP or IPX address of destination
unsigned char destAtm_addr[20]; ATM address of destination
unsigned int mpcIndex; Index of MPC
unsigned int mpsIndex; Index of MPS
} |
TRAP-TYPE |
|
|
|
mpcIngressRetryTimeOut13 |
69 |
A ingress retry timeout trap occurs when the retry time exceed the
MPC-p5 time.
The Trap PDU data format:
struct {
unsigned int mpcIndex; Index of MPC
unsigned int max_timeout_sec; Timeout value in second
unsigned char destNet_addr[10]; IP or IPX address of destination
unsigned char destAtm_addr[20]; ATM address of destination
unsigned int prototype; 1: IP, 11: IPX
unsigned int mpsIndex; Index of MPS
} |
TRAP-TYPE |
|
|
|
oamVCAIS13 |
71 |
This trap signifies that the specified connection is in VC-AIS
state. |
TRAP-TYPE |
|
|
|
oamVCRDI13 |
72 |
This trap signifies that the specified connection is in VC-RDI
state. |
TRAP-TYPE |
|
|
|
oamVCLOC13 |
73 |
This trap signifies that the specified connection is in VC-LOC
state. |
TRAP-TYPE |
|
|
|
oamVCUnsuccessLoop13 |
74 |
This trap signifies that the specified connection is unsuccessful
Loopback state. |
TRAP-TYPE |
|
|
|
oamVPAIS13 |
75 |
This trap signifies that the specified VP connection is in VP-AIS
state. |
TRAP-TYPE |
|
|
|
oamVPRDI13 |
76 |
This trap signifies that the specified VP connection is in VP-RDI
state. |
TRAP-TYPE |
|
|
|
oamVPLOC13 |
77 |
This trap signifies that the specified VP connection is in VP-LOC
state. |
TRAP-TYPE |
|
|
|
oamVPUnsuccessLoop13 |
78 |
This trap signifies that the specified VP connection is in
Unsuccessful loopback state. |
TRAP-TYPE |
|
|
|
ldpPeerCreate13 |
80 |
A LDP peer is identified by LDP Hello mechanism and
peer entry is created. |
TRAP-TYPE |
|
|
|
ldpSessionCreate13 |
82 |
A LDP session with the peer is established and a session entry
is created. |
TRAP-TYPE |
|
|
|
ldpSessionDelete13 |
83 |
A LDP session with the peer is lost and session entry is deleted. |
TRAP-TYPE |
|
|
|
accountEvent13 |
86 |
An account event is generated to signal that a
new accounting file is available on the switch. |
TRAP-TYPE |
|
|
|
accountOver1Event13 |
87 |
This event is generated when the filling level
exceeds the first threshold.
This event is for information only, and signals
that accounting data are accumulating on the switch. |
TRAP-TYPE |
|
|
|
accountUnder1Event13 |
88 |
This event is generated when the filling level
goes below the first threshold.
This event is for information only. |
TRAP-TYPE |
|
|
|
accountOver2Alarm13 |
89 |
This alarm is generated when the filling level
exceeds the second threshold.
It signals that the switch changes over to the
alternate collection device. |
TRAP-TYPE |
|
|
|
accountUnder2Event13 |
90 |
This event is generated when the filling level
is lowering below the second threshold. |
TRAP-TYPE |
|
|
|
accountOver3Alarm13 |
91 |
This event is generated when the filling level
exceeds the third threshold.
It signals that the switch is now in congestion. |
TRAP-TYPE |
|
|
|
accountUnder3Event13 |
92 |
This event is generated when the filling level
is lowering below the third threshold. |
TRAP-TYPE |
|
|
|
accountNoDeviceAlarm13 |
93 |
This alarm is generated when the TCP connection
establishment fails with both the primary and the
secondary collection devices. |
TRAP-TYPE |
|
|
|
accountFileAlarm13 |
94 |
This alarm is generated when too many files are
awaiting collection. |
TRAP-TYPE |
|
|
|
lecStateChangeEvent13 |
96 |
When a Lec status changes, a trap message will be send out to a network
manager, the trap packet has the data format:
struct {
unsigned int lec_id;
unsigned char elan_name[33];
unsigned char atm_addr[20];
unsigned int slot_number;
unsigned int port_number;
unsigned int service_number;
unsigned int new_state;
unsigned int pre_state;
unsigned int reason_of_change;
} |
TRAP-TYPE |
|
|
|
fantrayEvent13 |
97 |
A fantrayEvent trap occurs when a problem condition
is recognized on a chassis fan tray. |
TRAP-TYPE |
|
|
|
sonetAisTypeTrap13 |
98 |
This trap is generated when there is any of the following
AIS types of errors on Sonet PMC
SONET_LINK_RX_AIS,
SEC_LINE_AIS,
SEC_PATH_AIS. |
TRAP-TYPE |
|
|
|
sonetRdiTypeTrap13 |
99 |
This trap is generated when there is any of the following
RDI types of errors on Sonet
SONET_LINK_RX_RDI,
SEC_LINE_RDI,
SEC_PATH_RDI. |
TRAP-TYPE |
|
|
|