TIMETRA-LOG-MIB

File: TIMETRA-LOG-MIB.mib (174013 bytes)

Imported modules

SNMPv2-SMI	SNMPv2-CONF	SNMPv2-TC
SNMPv2-MIB	SNMP-FRAMEWORK-MIB	SNMP-NOTIFICATION-MIB
INET-ADDRESS-MIB	TIMETRA-TC-MIB	TIMETRA-GLOBAL-MIB
TIMETRA-FILTER-MIB

Imported symbols

MODULE-IDENTITY	OBJECT-TYPE	NOTIFICATION-TYPE
Unsigned32	Integer32	IpAddress
Counter32	Counter64	MODULE-COMPLIANCE
OBJECT-GROUP	NOTIFICATION-GROUP	TEXTUAL-CONVENTION
RowStatus	StorageType	TruthValue
DateAndTime	DisplayString	TimeStamp
sysDescr	sysObjectID	SnmpMessageProcessingModel
SnmpSecurityLevel	SnmpAdminString	snmpNotifyEntry
InetAddressType	InetAddress	TItemDescription
TNamedItemOrEmpty	TNamedItem	TmnxAdminState
TmnxOperState	TmnxActionType	TQueueId
THsmdaCounterIdOrZero	TmnxAccPlcyQICounters	TmnxAccPlcyQECounters
TmnxAccPlcyOICounters	TmnxAccPlcyOECounters	TmnxAccPlcyAACounters
THsmdaCounterIdOrZeroOrAll	TQueueIdOrAll	timetraSRMIBModules
tmnxSRObjs	tmnxSRConfs	tmnxSRNotifyPrefix
TFilterAction	TFilterActionOrDefault

Defined Types

TmnxPerceivedSeverity
ITU perceived severity values as per M.3100 and X.733
TEXTUAL-CONVENTION
	INTEGER	none(0), cleared(1), indeterminate(2), critical(3), major(4), minor(5), warning(6)

TmnxSyslogId
The value of TmnxSyslogId uniquely identifies an entry in the tmnxSyslogTargetTable to be used for the syslog collector target information when creating a log file where tmnxLogIdDestination has a value of 'syslog (2)'.
TEXTUAL-CONVENTION
	INTEGER	1..10

TmnxSyslogIdOrEmpty
The value of TmnxSyslogIdOrEmpty uniquely identifies an entry in the tmnxSyslogTargetTable to be used for the syslog collector target information when creating a log file where tmnxLogIdDestination has a value of 'syslog (2)'. The value of 0 is used when no entry exists in the tmnxSyslogTargetTable.
TEXTUAL-CONVENTION
	INTEGER	0 | 1..10

TmnxSyslogFacility
The value of TmnxSyslogFacility is an enumerated integer that specifies which syslog facility is the intended destination for the log event stream.
TEXTUAL-CONVENTION
	INTEGER	kernel(0), user(1), mail(2), systemd(3), auth(4), syslogd(5), printer(6), netnews(7), uucp(8), cron(9), authpriv(10), ftp(11), ntp(12), logaudit(13), logalert(14), cron2(15), local0(16), local1(17), local2(18), local3(19), local4(20), local5(21), local6(22), local7(23)

TmnxUdpPort
The value of TmnxUdpPort is the port used to send messages to an event collector target. 514 is the IANA assigned port number for syslog. 162 is the IANA assigned port number for SNMP notifications.
TEXTUAL-CONVENTION
	INTEGER	0..65535

TmnxSyslogSeverity
The value of TmnxSyslogSeverity is an enumerated integer that specifies the severity levels of syslog messages.
TEXTUAL-CONVENTION
	INTEGER	emergency(0), alert(1), critical(2), error(3), warning(4), notice(5), info(6), debug(7)

TmnxLogFileId
The value of TmnxLogFileId uniquely identifies a file-id to be used when creating a log or billing file. A value of zero (0) indicates none specified and is invalid when used as an index for the tmnxLogFileIdTable.
TEXTUAL-CONVENTION
	INTEGER	0..99

TmnxLogFileType
The value of TmnxLogFileType indicates the type of information that will be written to this file.
TEXTUAL-CONVENTION
	INTEGER	none(0), eventLog(1), accountingPolicy(2)

TmnxLogIdIndex
The value of tmnxLogIdIndex uniquely identifies an event stream log. Note that 2 default TmnxLogIdEntry rows are created by the agent using TmnxLogIdIndex values 99 and 100.
TEXTUAL-CONVENTION
	INTEGER	1..100

TmnxCFlash
The value of TmnxCFlash uniquely identifies a compact flash module on the active CPM card. A value of zero (0) indicates none specified.
TEXTUAL-CONVENTION
	Unsigned32

TmnxLogFilterId
The value of TmnxLogFilterId is the identification number of an event log filter. The value of zero indicates none specified. The value of zero (0) is invalid when used as an index for the tmnxLogFilterTable. Filter entry 1001 is created by the agent.
TEXTUAL-CONVENTION
	Unsigned32	0..1001

TmnxLogFilterEntryId
The value of TmnxLogFilterEntryId is the identification number of an event log filter entry.
TEXTUAL-CONVENTION
	Unsigned32	1..999

TmnxLogFilterOperator
When TmnxLogFilterOperator has a value of 'off', the item is not matched. Otherwise the value of TmnxLogFilterOperator determines the comparison operator to be used as the parameter match criterion.
TEXTUAL-CONVENTION
	INTEGER	off(1), equal(2), notEqual(3), lessThan(4), lessThanOrEqual(5), greaterThan(6), greaterThanOrEqual(7)

TmnxEventNumber
Each log event type has a unique identifying number. This number is unique within a particular software application, such as IP, MPLS, OSPF, etc.; but it is not necessarily unique across different software applications. That is MPLS event #1001 may be different from OSPF event #1001.
TEXTUAL-CONVENTION
	Unsigned32

TmnxLogFileIdEntry
SEQUENCE
	tmnxLogFileId	TmnxLogFileId
	tmnxLogFileIdRowStatus	RowStatus
	tmnxLogFileIdStorageType	StorageType
	tmnxLogFileIdRolloverTime	Integer32
	tmnxLogFileIdRetainTime	Integer32
	tmnxLogFileIdAdminLocation	TmnxCFlash
	tmnxLogFileIdOperLocation	TmnxCFlash
	tmnxLogFileIdDescription	TItemDescription
	tmnxLogFileIdLogType	TmnxLogFileType
	tmnxLogFileIdLogId	Integer32
	tmnxLogFileIdPathName	DisplayString
	tmnxLogFileIdCreateTime	DateAndTime
	tmnxLogFileIdBackupLoc	TmnxCFlash

TmnxLogApEntry
SEQUENCE
	tmnxLogApPolicyId	Integer32
	tmnxLogApRowStatus	RowStatus
	tmnxLogApStorageType	StorageType
	tmnxLogApAdminStatus	TmnxAdminState
	tmnxLogApOperStatus	TmnxOperState
	tmnxLogApInterval	Integer32
	tmnxLogApDescription	TItemDescription
	tmnxLogApDefault	TruthValue
	tmnxLogApRecord	INTEGER
	tmnxLogApToFileId	TmnxLogFileId
	tmnxLogApPortType	INTEGER
	tmnxLogApDefaultInterval	TruthValue
	tmnxLogApDataLossCount	Counter32
	tmnxLogApLastDataLossTimeStamp	TimeStamp
	tmnxLogApToFileType	INTEGER

TmnxLogIdEntry
SEQUENCE
	tmnxLogIdIndex	TmnxLogIdIndex
	tmnxLogIdRowStatus	RowStatus
	tmnxLogIdStorageType	StorageType
	tmnxLogIdAdminStatus	TmnxAdminState
	tmnxLogIdOperStatus	TmnxOperState
	tmnxLogIdDescription	TItemDescription
	tmnxLogIdFilterId	TmnxLogFilterId
	tmnxLogIdSource	BITS
	tmnxLogIdDestination	INTEGER
	tmnxLogIdFileId	TmnxLogFileId
	tmnxLogIdSyslogId	TmnxSyslogIdOrEmpty
	tmnxLogIdMaxMemorySize	Unsigned32
	tmnxLogIdConsoleSession	TruthValue
	tmnxLogIdForwarded	Counter64
	tmnxLogIdDropped	Counter64
	tmnxLogIdTimeFormat	INTEGER

TmnxLogFilterEntry
SEQUENCE
	tmnxLogFilterId	TmnxLogFilterId
	tmnxLogFilterRowStatus	RowStatus
	tmnxLogFilterDescription	TItemDescription
	tmnxLogFilterDefaultAction	TFilterAction
	tmnxLogFilterInUse	TruthValue

TmnxLogFilterParamsEntry
SEQUENCE
	tmnxLogFilterParamsIndex	TmnxLogFilterEntryId
	tmnxLogFilterParamsRowStatus	RowStatus
	tmnxLogFilterParamsDescription	TItemDescription
	tmnxLogFilterParamsAction	TFilterActionOrDefault
	tmnxLogFilterParamsApplication	TNamedItemOrEmpty
	tmnxLogFilterParamsApplOperator	TmnxLogFilterOperator
	tmnxLogFilterParamsNumber	TmnxEventNumber
	tmnxLogFilterParamsNumberOperator	TmnxLogFilterOperator
	tmnxLogFilterParamsSeverity	TmnxPerceivedSeverity
	tmnxLogFilterParamsSeverityOperator	TmnxLogFilterOperator
	tmnxLogFilterParamsSubject	TNamedItemOrEmpty
	tmnxLogFilterParamsSubjectOperator	TmnxLogFilterOperator
	tmnxLogFilterParamsSubjectRegexp	TruthValue
	tmnxLogFilterParamsRouter	TNamedItemOrEmpty
	tmnxLogFilterParamsRouterOperator	TmnxLogFilterOperator
	tmnxLogFilterParamsRouterRegexp	TruthValue

TmnxSyslogTargetEntry
SEQUENCE
	tmnxSyslogTargetIndex	TmnxSyslogId
	tmnxSyslogTargetRowStatus	RowStatus
	tmnxSyslogTargetDescription	TItemDescription
	tmnxSyslogTargetAddress	IpAddress
	tmnxSyslogTargetUdpPort	TmnxUdpPort
	tmnxSyslogTargetFacility	TmnxSyslogFacility
	tmnxSyslogTargetSeverity	TmnxSyslogSeverity
	tmnxSyslogTargetMessagePrefix	TNamedItemOrEmpty
	tmnxSyslogTargetMessagesDropped	Counter32
	tmnxSyslogTargetAddrType	InetAddressType
	tmnxSyslogTargetAddr	InetAddress

TmnxEventAppEntry
SEQUENCE
	tmnxEventAppIndex	Unsigned32
	tmnxEventAppName	TNamedItem

TmnxEventEntry
SEQUENCE
	tmnxEventID	Unsigned32
	tmnxEventName	TNamedItem
	tmnxEventSeverity	TmnxPerceivedSeverity
	tmnxEventControl	TruthValue
	tmnxEventCounter	Counter32
	tmnxEventDropCount	Counter32
	tmnxEventReset	TmnxActionType
	tmnxEventThrottle	TruthValue

TmnxSnmpTrapGroupEntry
SEQUENCE
	tmnxStgIndex	TmnxLogIdIndex
	tmnxStgDestAddress	IpAddress
	tmnxStgDestPort	TmnxUdpPort
	tmnxStgRowStatus	RowStatus
	tmnxStgDescription	TItemDescription
	tmnxStgVersion	SnmpMessageProcessingModel
	tmnxStgNotifyCommunity	OCTET STRING
	tmnxStgSecurityLevel	SnmpSecurityLevel

TmnxSnmpSetErrsEntry
SEQUENCE
	tmnxSseAddressType	InetAddressType
	tmnxSseAddress	InetAddress
	tmnxSseSnmpPort	TmnxUdpPort
	tmnxSseRequestId	Unsigned32
	tmnxSseVersion	SnmpMessageProcessingModel
	tmnxSseSeverityLevel	TmnxPerceivedSeverity
	tmnxSseModuleId	Unsigned32
	tmnxSseModuleName	TNamedItem
	tmnxSseErrorCode	Unsigned32
	tmnxSseErrorName	DisplayString
	tmnxSseErrorMsg	DisplayString
	tmnxSseExtraText	OCTET STRING
	tmnxSseTimestamp	TimeStamp

TmnxSnmpTrapLogEntry
SEQUENCE
	tmnxSnmpTrapLogDescription	TItemDescription

TmnxSnmpTrapDestEntry
SEQUENCE
	tmnxStdIndex	TmnxLogIdIndex
	tmnxStdName	SnmpAdminString
	tmnxStdRowStatus	RowStatus
	tmnxStdRowLastChanged	TimeStamp
	tmnxStdDestAddrType	InetAddressType
	tmnxStdDestAddr	InetAddress
	tmnxStdDestPort	TmnxUdpPort
	tmnxStdDescription	TItemDescription
	tmnxStdVersion	SnmpMessageProcessingModel
	tmnxStdNotifyCommunity	OCTET STRING
	tmnxStdSecurityLevel	SnmpSecurityLevel
	tmnxStdReplay	TruthValue
	tmnxStdReplayStart	Unsigned32
	tmnxStdReplayLastTime	TimeStamp

TmnxLogApCustRecordEntry
SEQUENCE
	tmnxLogApCrLastChanged	TimeStamp
	tmnxLogApCrSignChangeDelta	Unsigned32
	tmnxLogApCrSignChangeQueue	TQueueIdOrAll
	tmnxLogApCrSignChangeOCntr	THsmdaCounterIdOrZeroOrAll
	tmnxLogApCrSignChangeQICounters	TmnxAccPlcyQICounters
	tmnxLogApCrSignChangeQECounters	TmnxAccPlcyQECounters
	tmnxLogApCrSignChangeOICounters	TmnxAccPlcyOICounters
	tmnxLogApCrSignChangeOECounters	TmnxAccPlcyOECounters
	tmnxLogApCrSignChangeAACounters	TmnxAccPlcyAACounters
	tmnxLogApCrAACounters	TmnxAccPlcyAACounters

TmnxLogApCustRecordQueueEntry
SEQUENCE
	tmnxLogApCrQueueId	TQueueId
	tmnxLogApCrQueueRowStatus	RowStatus
	tmnxLogApCrQueueLastChanged	TimeStamp
	tmnxLogApCrQueueICounters	TmnxAccPlcyQICounters
	tmnxLogApCrQueueECounters	TmnxAccPlcyQECounters

TmnxLogApCrOverrideCntrEntry
SEQUENCE
	tmnxLogApCrOverrideCntrId	THsmdaCounterIdOrZero
	tmnxLogApCrOverrideCntrRowStatus	RowStatus
	tmnxLogApCrOverrideCntrLastChngd	TimeStamp
	tmnxLogApCrOverrideCntrICounters	TmnxAccPlcyOICounters
	tmnxLogApCrOverrideCntrECounters	TmnxAccPlcyOECounters

TmnxLogExecRollbackOpEntry
SEQUENCE
	tmnxLogExRbkOpIndex	Unsigned32
	tmnxLogExRbkOpLastChanged	TimeStamp
	tmnxLogExRbkOpType	INTEGER
	tmnxLogExRbkOpStatus	INTEGER
	tmnxLogExRbkOpBegin	TimeStamp
	tmnxLogExRbkOpEnd	TimeStamp
	tmnxLogExRbkOpFile	DisplayString
	tmnxLogExRbkOpUser	TNamedItem
	tmnxLogExRbkOpNumEvents	Unsigned32

TmnxLogExecRollbackEventEntry
SEQUENCE
	tmnxLogExRbkEventIndex	Unsigned32
	tmnxLogExRbkEventOID	OBJECT IDENTIFIER

Defined Values

timetraLogMIBModule		1.3.6.1.4.1.6527.1.1.3.12
This document is the SNMP MIB module to manage and provision the Alcatel-Lucent SROS Logging utility. Copyright 2003-2012 Alcatel-Lucent. All rights reserved. Reproduction of this document is authorized on the condition that the foregoing copyright notice is included. This SNMP MIB module (Specification) embodies Alcatel-Lucent's proprietary intellectual property. Alcatel-Lucent retains all title and ownership in the Specification, including any revisions. Alcatel-Lucent grants all interested parties a non-exclusive license to use and distribute an unmodified copy of this Specification in connection with management of Alcatel-Lucent products, and without fee, provided this copyright notice and license appear on all copies. This Specification is supplied 'as is', and Alcatel-Lucent makes no warranty, either express or implied, as to the use, operation, condition, or performance of the Specification.
MODULE-IDENTITY

tmnxLogObjs		1.3.6.1.4.1.6527.3.1.2.12
OBJECT IDENTIFIER

tmnxLogNotificationObjects		1.3.6.1.4.1.6527.3.1.2.12.1
OBJECT IDENTIFIER

tmnxLogNotifyPrefix		1.3.6.1.4.1.6527.3.1.3.12
OBJECT IDENTIFIER

tmnxLogNotifications		1.3.6.1.4.1.6527.3.1.3.12.0
OBJECT IDENTIFIER

tmnxLogConformance		1.3.6.1.4.1.6527.3.1.1.12
OBJECT IDENTIFIER

tmnxLogMaxLogs		1.3.6.1.4.1.6527.3.1.2.12.2
The maximum number of concurrent active Logs that are allowed. A value of zero (0) for this object implies that there is no limit for the number of concurrent active logs in effect.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

tmnxLogFileIdTable		1.3.6.1.4.1.6527.3.1.2.12.3
Defines the Alcatel-Lucent SROS series Log File ID Table for providing, via SNMP, the capability of defining the characteristics for log and billing files and associating them with a file-id. The actual file is not created until the file-id is used in a log or billing file configuration.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TmnxLogFileIdEntry

tmnxLogFileIdEntry		1.3.6.1.4.1.6527.3.1.2.12.3.1
Defines an entry in the tmnxLogFileIdTable. Entries are created and deleted in this table by SNMP sets to tmnxLogFileIdRowStatus.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxLogFileIdEntry

tmnxLogFileId		1.3.6.1.4.1.6527.3.1.2.12.3.1.1
The index value tmnxLogFileId uniquely identifies a file-id to be used when creating a log or billing file.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxLogFileId

tmnxLogFileIdRowStatus		1.3.6.1.4.1.6527.3.1.2.12.3.1.2
This object allows entries to be created and deleted in the tmnxLogFileIdTable. Deletion of an entry in this table will not succeed if it is currently used by any log or billing file.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

tmnxLogFileIdStorageType		1.3.6.1.4.1.6527.3.1.2.12.3.1.3
The storage type for this conceptual row. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row.
Status: current	Access: read-create
OBJECT-TYPE
	StorageType

tmnxLogFileIdRolloverTime		1.3.6.1.4.1.6527.3.1.2.12.3.1.4
The value of tmnxLogFileIdRolloverTime specifies how often, in minutes, a new log or billing file will be created. If the value of tmnxLogFileIdLogType is not 'rollover', then the value of this object is irrelevant.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	5..10080

tmnxLogFileIdRetainTime		1.3.6.1.4.1.6527.3.1.2.12.3.1.5
The value of tmnxLogFileIdRetainTime specifies the minimum time, in hours, that a file is retained on the media. Once this time period has expired the file is deleted.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..500

tmnxLogFileIdAdminLocation		1.3.6.1.4.1.6527.3.1.2.12.3.1.6
The value of tmnxLogFileIdAdminLocation specifies where the log or billing file should be created. The file location should be a compact flash on the primary CPM. When the secondary CPM becomes the primary CPM after a failure, the same log file policies will be activated. Thus it is recommended that the same media is available to both secondary and primary CPMs. If no location is specified, 0, the compact flash cf1: is used to store the log files or cf2: is used to store billing files.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxCFlash

tmnxLogFileIdOperLocation		1.3.6.1.4.1.6527.3.1.2.12.3.1.7
The value of tmnxLogFileIdOperLocation specifies where the log or billing file has been created. The file location should be a compact flash on the primary CPM. When the secondary CPM becomes the primary CPM after a failure, the same log file policies will be activated. Thus it is recommended that the same media is available to both secondary and primary CPMs.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxCFlash

tmnxLogFileIdDescription		1.3.6.1.4.1.6527.3.1.2.12.3.1.8
The value of tmnxLogFileIdDescription is a user provided description string for this log file-id entry. It can consist of any printable, seven-bit ASCII characters up to 80 characters in length.
Status: current	Access: read-create
OBJECT-TYPE
	TItemDescription

tmnxLogFileIdLogType		1.3.6.1.4.1.6527.3.1.2.12.3.1.9
The value of tmnxLogFileIdLogType indicates the type of information that will be written to this file.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxLogFileType

tmnxLogFileIdLogId		1.3.6.1.4.1.6527.3.1.2.12.3.1.10
The value of tmnxLogFileIdLogId indicates the ID index of the log or accounting policy this file is attached to. A value of zero (0) indicates that this file definition is not currently used by any log or accounting policy.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..99

tmnxLogFileIdPathName		1.3.6.1.4.1.6527.3.1.2.12.3.1.11
The value of tmnxLogFileIdPathName is the pathname of the currently opened file used by this file-id entry.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

tmnxLogFileIdCreateTime		1.3.6.1.4.1.6527.3.1.2.12.3.1.12
The value of tmnxLogFileIdCreateTime is the time the currently opened file version used by this file-id entry was created.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

tmnxLogFileIdBackupLoc		1.3.6.1.4.1.6527.3.1.2.12.3.1.13
The value of tmnxLogFileIdBackupLoc specifies where the log or billing file should be created if it cannot be created in the location specified by tmnxLogFileIdAdminLocation. The file location should be a compact flash on the primary CPM. When the secondary CPM becomes the primary CPM after a failure, the same log file policies will be activated. Thus it is recommended that the same media is available to both secondary and primary CPMs. If no backup location is specified, 0, and the log or billing file could not be created in the location specified by tmnxLogFileIdAdminLocation or the file creation at the specified backup location fails, a file create failure trap is issued and the associated log or accounting policy is marked as operationally 'outOfService'.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxCFlash

tmnxLogApTable		1.3.6.1.4.1.6527.3.1.2.12.4
The Alcatel-Lucent SROS series Log Accounting Policy Table contains an entry for each accounting policy that specifies the characteristics of the accounting records associated with an accounting policy.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TmnxLogApEntry

tmnxLogApEntry		1.3.6.1.4.1.6527.3.1.2.12.4.1
Defines an entry in the tmnxLogApTable. Entries in the tmnxLogApTable are created and destroyed via SNMP Set requests to tmnxLogApRowStatus.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxLogApEntry

tmnxLogApPolicyId		1.3.6.1.4.1.6527.3.1.2.12.4.1.1
The value of tmnxLogApPolicyId uniquely identifies an accounting policy to be used for creating accounting records. A specific accounting policy can be applied to one or more service access points (SAPs). Any changes made to an existing policy is applied immediately to all SAPs where this policy is applied.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..99

tmnxLogApRowStatus		1.3.6.1.4.1.6527.3.1.2.12.4.1.2
This object allows entries to be created and deleted in the tmnxLogApTable. Deletion of an entry in this table will not succeed if it is currently applied to any service access point (SAP).
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

tmnxLogApStorageType		1.3.6.1.4.1.6527.3.1.2.12.4.1.3
The storage type for this conceptual row. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row.
Status: current	Access: read-create
OBJECT-TYPE
	StorageType

tmnxLogApAdminStatus		1.3.6.1.4.1.6527.3.1.2.12.4.1.4
The value of tmnxLogApAdminStatus specifies the desired administrative state for this accounting policy.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxAdminState

tmnxLogApOperStatus		1.3.6.1.4.1.6527.3.1.2.12.4.1.5
The value of tmnxLogApOperStatus indicates the current operational status of this accounting policy.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxOperState

tmnxLogApInterval		1.3.6.1.4.1.6527.3.1.2.12.4.1.6
The value of tmnxLogApInterval determines how frequently the statistics are collected and written to their destination. tmnxLogApInterval will have a default value if the value of tmnxLogApDefaultInterval is set to 'true'. Value of tmnxLogApInterval can be set manually if tmnxLogApDefaultInterval is set to 'false'. An attempt to set this object to a non-default value will fail with an inconsistentValue error if tmnxLogApDefaultInterval has the value 'true' set. If no record is specified, default value for tmnxLogApInterval is 5 minutes. For service and network types of record, default values are 5 minutes and 15 minutes respectively. For SAA only, the minimum value of tmnxLogApInterval is 1 minute. Otherwise the minimum value is 5 minutes.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..120

tmnxLogApDescription		1.3.6.1.4.1.6527.3.1.2.12.4.1.7
The value of tmnxLogApDescription is a user provided description string for this accounting policy. It can consist of any printable, seven-bit ASCII characters up to 80 characters in length.
Status: current	Access: read-create
OBJECT-TYPE
	TItemDescription

tmnxLogApDefault		1.3.6.1.4.1.6527.3.1.2.12.4.1.8
When tmnxLogApDefault has a value of 'true', it indicates that this accounting policy is applied to all service access points (SAPs) that do not have an explicit accounting policy applied. If no accounting policy is associated with a SAP accounting records are produced in accordance with the default policy. Only one accounting policy entry in the tmnxLogApTable can have tmnxLogApDefault set to 'true'. If there is no entry in the tmnxLogApTable with tmnxLogApDefault set to 'true', then the only accounting records collected are those explicitly configured accounting policies.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

tmnxLogApRecord		1.3.6.1.4.1.6527.3.1.2.12.4.1.9
The value of tmnxLogApRecord indicates the type of predefined accounting record type to be written to the accounting file. When tmnxLogApDefaultInterval has a value of 'false', statistics collection interval of the record type will be ignored. The value 'bsxSubscriberAppGroup (22)' was made obsolete in release 7.0 and replaced by 'custom-record-aa (25).'
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	none(0), svcIngressOctet(1), svcEgressOctet(2), svcIngressPkt(3), svcEgressPkt(4), netIngressOctet(5), netEgressOctet(6), netIngressPkt(7), netEgressPkt(8), compactSvcInOctet(9), combinedSvcIngress(10), combinedNetInEgOctet(11), combinedSvcInEgOctet(12), completeSvcInEg(13), combinedSvcSdpInEg(14), completeSvcSdpInEg(15), completeSubscrIngrEgr(16), bsxProtocol(17), bsxApplication(18), bsxAppGroup(19), bsxSubscriberProtocol(20), bsxSubscriberApplication(21), bsxSubscriberAppGroup(22), customRecordSubscriber(23), customRecordService(24), customRecordAa(25), queueGroupOctets(26), queueGroupPackets(27), combinedQueueGroup(28), combinedMplsLspIngress(29), combinedMplsLspEgress(30), combinedLdpLspEgress(31), saa(32), video(33), kpiSystem(34), kpiBearerMgmt(35), kpiBearerTraffic(36), kpiRefPoint(37), kpiPathMgmt(38), kpiIom3(39), kciSystem(40), kciBearerMgmt(41), kciPathMgmt(42), completeKpi(43), completeKci(44), kpiBearerGroup(45), kpiRefPathGroup(46), kpiKciBearerMgmt(47), kpiKciPathMgmt(48), kpiKciSystem(49), completeKpiKci(50), aaPerformance(51), netInfIngressOct(52), netInfIngressPkt(53), combinedNetInfIngress(54), accessEgressPkt(55), accessEgressOct(56), combinedAccessEgress(57), combinedNetEgress(58), combinedSvcEgress(59), combinedSvcInEgPkt(60), combinedNetInEgPkt(61)

tmnxLogApToFileId		1.3.6.1.4.1.6527.3.1.2.12.4.1.10
The value of tmnxLogApToFileId is the index to the entry in the tmnxLogFileIdTable that specifies the file characteristics to be used for the destination of the accounting policy records collected by this accounting policy. The file itself is created the first time this accounting policy is applied to a service access point (SAP). tmnxLogApToFileId must be set along with tmnxLogApToFileType to indicate whether the records will be stored in a file or not. When a destination file is specified, the value of the file is specified by tmnxLogApToFileId and the value of tmnxLogApToFileType should be 'fileId'. When the destination file is not specified, the value of tmnxLogApToFileId should be zero and the value of tmnxLogApToFileType should be 'noFile'.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxLogFileId

tmnxLogApPortType		1.3.6.1.4.1.6527.3.1.2.12.4.1.11
The tmnxLogApPortType variable indicates if this accounting policy's record type is to be associated with a service access port, a network access port, a service destination point, a subscriber or the application-assurance feature.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(0), access(1), network(2), sdp(3), subscriber(4), appAssure(5), qgrp(6), saa(7), mplsLspIngr(8), mplsLspEgr(9), ldpLspEgr(10), video(11), mobileGateway(12), networkIf(13), accessport(14)

tmnxLogApDefaultInterval		1.3.6.1.4.1.6527.3.1.2.12.4.1.12
When tmnxLogApDefaultInterval has a value of 'true', it indicates that tmnxLogApInterval will have a default value. When tmnxLogApDefaultInterval has a value of 'false', user can set the value of tmnxLogApInterval manually.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

tmnxLogApDataLossCount		1.3.6.1.4.1.6527.3.1.2.12.4.1.13
The value of tmnxLogApDataLossCount indicates the number of times a tmnxLogAccountingDataLoss trap was raised against this application policy.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

tmnxLogApLastDataLossTimeStamp		1.3.6.1.4.1.6527.3.1.2.12.4.1.14
The value of tmnxLogApLastDataLossTimeStamp indicates the last time, since system startup that a tmnxLogAccountingDataLoss trap was raised against this application policy.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

tmnxLogApToFileType		1.3.6.1.4.1.6527.3.1.2.12.4.1.15
The value of tmnxLogApToFileType indicates where records of an accounting policy are stored. It should be set along with tmnxLogApToFileId which specifies the destination file index where the accounting records are stored. When the value of tmnxLogApToFileType is 'noFile', it indicates that the accounting records will not to be stored in a file and the value of tmnxLogApToFileId should be set to zero. When the value of tmnxLogApToFileType is 'fileId', it indicates that the accounting records will be stored in a file specified by tmnxLogApToFileId. tmnxLogApOperStatus will transition to 'inService' when the tmnxLogApToFileType is set to 'noFile' or 'fileId'.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	fileId(0), noFile(1)

tmnxLogIdTable		1.3.6.1.4.1.6527.3.1.2.12.5
The Alcatel-Lucent SROS series Log Identification Table contains an entry for each log that specifies the characteristics of that log associated with a log-id number.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TmnxLogIdEntry

tmnxLogIdEntry		1.3.6.1.4.1.6527.3.1.2.12.5.1
Defines an entry in the tmnxLogIdTable. Entries in the tmnxLogIdTable are created and destroyed via SNMP Set requests to tmnxLogIdRowStatus. Default log entries 99 and 100 are created by the agent.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxLogIdEntry

tmnxLogIdIndex		1.3.6.1.4.1.6527.3.1.2.12.5.1.1
The value of tmnxLogIdIndex uniquely identifies an event stream log.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxLogIdIndex

tmnxLogIdRowStatus		1.3.6.1.4.1.6527.3.1.2.12.5.1.2
This object allows entries to be created and deleted in the tmnxLogIdTable. Deletion of an entry in this table will not succeed if tmnxLogIdOperStatus is not 'outOfService'. tmnxLogIdOperStatus will not transition to 'inService' if tmnxLogIdSource and tmnxLogIdDestination and their associated objects have not been set to valid values.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

tmnxLogIdStorageType		1.3.6.1.4.1.6527.3.1.2.12.5.1.3
The storage type for this conceptual row. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row.
Status: current	Access: read-create
OBJECT-TYPE
	StorageType

tmnxLogIdAdminStatus		1.3.6.1.4.1.6527.3.1.2.12.5.1.4
The value of tmnxLogIdAdminStatus indicates the desired administrative state for this log.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxAdminState

tmnxLogIdOperStatus		1.3.6.1.4.1.6527.3.1.2.12.5.1.5
The value of tmnxLogIdOperStatus indicates the current operational status of this log.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxOperState

tmnxLogIdDescription		1.3.6.1.4.1.6527.3.1.2.12.5.1.6
The value of tmnxLogIdDescription is a user provided description string for this log. It can consist of any printable, seven-bit ASCII characters up to 80 characters in length.
Status: current	Access: read-create
OBJECT-TYPE
	TItemDescription

tmnxLogIdFilterId		1.3.6.1.4.1.6527.3.1.2.12.5.1.7
The value of tmnxLogIdFilterId is the index into the tmnxLogFilterTable to the entry the defines a filter to be applied to this log's source event stream to limit the events output to this log's destination. If tmnxLogIdFilterId has a value of 0, then all events in the source log are forwarded to the destination.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxLogFilterId

tmnxLogIdSource		1.3.6.1.4.1.6527.3.1.2.12.5.1.8
The value of tmnxLogIdSource is a bit mask that specifies the log event source stream(s) to be forwarded to the destination specified in tmnxLogIdDestination. Events from more than one source may be forwarded to the log destination. The 'main' event stream consists of all events that are not explicitly directed to any other event stream. The 'security' event stream contains all events that affect attempts to breach system security such as failed login attempts, attempts to access SNMP MIB tables to which the user has not been granted access, or attempts to enter a branch of the CLI for which the user is not authorized. The 'user' activity event stream contains all events that directly affect the configuration or operation of the system. The 'debugTrace' event stream contains all events configured for application or protocol tracing. The 'li' event stream contains all events configured for Lawful Intercept activities. An attempt to set the 'li' event stream will fail with an inconsistentValue error if the requestor does not have access to the 'li' context. An attempt to set the 'li' event stream will fail with an inconsistentValue error if tmnxLogIdDestination has the value 'syslog' or 'file'.
Status: current	Access: read-create
OBJECT-TYPE
	BITS	main(0), security(1), change(2), debugTrace(3), li(4)

tmnxLogIdDestination		1.3.6.1.4.1.6527.3.1.2.12.5.1.9
The value of tmnxLogIdDestination specifies the event log stream destination. Once this object has been set to a value other than the default 'none' it cannot be modified and attempts to reset it to another value will fail with an INCONSISTENT VALUE error. The 'console' destination causes all selected log events to be directed to the system console. If the console is not connected then all entries are dropped. The 'syslog' destination sends all selected log events to the syslog address configured in tmnxSyslogTargetAddress and tmnxSyslogTargetUdpPort in the tmnxSyslogTargetTable row entry pointed to by the value of tmnxLogIdSyslogId. An attempt to set this object ot 'syslog' will fail with an inconsistentValue error if tmnxLogIdSource has the value 'li' set. The 'snmpTraps' destination causes events defined as SNMP traps to be sent to the configured SNMP trap destinations and also to be logged in the NOTIFICATION-LOG-MIB tables. The allocated memory size for the log of transmitted traps is specified in tmnxLogIdMaxMemorySize. The events are logged to memory in a circular fashion. Once the space is full, the oldest entry is replaced with a new entry. The 'file' destination causes all selected log events to be directed to a file on one of the CPM's compact flash discs. Details of the file's configuration are in the tmnxLogFileIdTable entry pointed to by the value of tmnxLogIdFileId. An attempt to set this object ot 'file' will fail with an inconsistentValue error if tmnxLogIdSource has the value 'li' set. The 'memory' destination causes all selected log events to be directed to an in memory storage area. The allocated memory size for the log is specified in tmnxLogIdMaxMemorySize. The events are logged to memory in a circular fashion. Once the space is full, the oldest entry is replaced with a new entry.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	none(0), console(1), syslog(2), snmpTraps(3), file(4), memory(5)

tmnxLogIdFileId		1.3.6.1.4.1.6527.3.1.2.12.5.1.10
The value of tmnxLogIdFileId is the index to the entry in the tmnxLogFileIdTable that specifies the file characteristics to be used for the destination of the log events written to this log. tmnxLogIdOperStatus will not transition to 'inService' until a valid value has been set for tmnxLogIdFileId. This object is valid only if tmnxLogIdDestination is set to 'file'.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxLogFileId

tmnxLogIdSyslogId		1.3.6.1.4.1.6527.3.1.2.12.5.1.11
The value of tmnxLogIdSyslogId is the index into the tmnxSyslogTargetTable for the row entry with the information to format event messages to be sent to a specific syslog collector target. This object is valid only when tmnxLogIdDestination has a value of 'syslog'. If this object has a value of zero (0), then no collector is specified and no messages are sent.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxSyslogIdOrEmpty

tmnxLogIdMaxMemorySize		1.3.6.1.4.1.6527.3.1.2.12.5.1.12
The value of tmnxLogIdMaxMemorySize specifies the amount of memory to allocate for this log. This object is valid only when tmnxLogIdDestination has a value of 'memory' or 'snmpTraps'. If the value tmnxLogIdDestination is neither 'memory' nor 'snmpTraps' a read of this object will return zero (0). Once a memory size has been specified and the log created, any attempt to modify this object will fail with an INCONSISTENT VALUE error.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0 | 50..3000

tmnxLogIdConsoleSession		1.3.6.1.4.1.6527.3.1.2.12.5.1.13
This object exists for the convenience of the Alcatel-Lucent SROS CLI. When set to 'true' it indicates that the 'CONSOLE' log output should be printed to the Telnet session instead of the CONSOLE device. When a tmnxLogIdEntry is created directly via SNMP, setting this object has no meaning and the 'CONSOLE' log output will always be sent to the CONSOLE device.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

tmnxLogIdForwarded		1.3.6.1.4.1.6527.3.1.2.12.5.1.14
The value of tmnxLogIdForwarded is the count of the number of events that have been forwarded to this log's destination. This counter is incremented after an event has been selected by the log filter defined in tmnxLogIdFilterId.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

tmnxLogIdDropped		1.3.6.1.4.1.6527.3.1.2.12.5.1.15
The value of tmnxLogIdDropped is the count of the number of events that have been sent to this logs source(s) and that have not been forwarded to the log destination because they were filtered out by the log filter defined in tmnxLogIdFilterId.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

tmnxLogIdTimeFormat		1.3.6.1.4.1.6527.3.1.2.12.5.1.16
The value of tmnxLogIdTimeFormat specifies the type of timestamp format for events sent to logs where tmnxLogIdDestination has a value of either 'syslog (2)' or 'file (4)'. When tmnxLogIdTimeFormat has a value of 'utc (1)' timestamps are written using the Coordinated Universal Time value. When tmnxLogIdTimeFormat has a value of 'local (2)' timestamps are written in the system's local time.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	utc(1), local(2)

tmnxLogFilterTable		1.3.6.1.4.1.6527.3.1.2.12.6
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TmnxLogFilterEntry

tmnxLogFilterEntry		1.3.6.1.4.1.6527.3.1.2.12.6.1
Information about a particular Log Filter entry. Entries are created by user. Entries are deleted by user. Entry 1001 is created by the agent for default TmnxLogIdIndex 100. There is no StorageType object. Entries have a presumed StorageType of nonVolatile.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxLogFilterEntry

tmnxLogFilterId		1.3.6.1.4.1.6527.3.1.2.12.6.1.1
The value of tmnxLogFilterId is a unique index that identifies a particular entry in the tmnxLogFilterTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxLogFilterId	1..1001

tmnxLogFilterRowStatus		1.3.6.1.4.1.6527.3.1.2.12.6.1.2
Row entries in this table are created and destroyed via SNMP set requests.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

tmnxLogFilterDescription		1.3.6.1.4.1.6527.3.1.2.12.6.1.3
The value of tmnxLogFilterDescription is a user provided description string for this log filter. It can consist of any printable, seven-bit ASCII characters up to 80 characters in length.
Status: current	Access: read-create
OBJECT-TYPE
	TItemDescription

tmnxLogFilterDefaultAction		1.3.6.1.4.1.6527.3.1.2.12.6.1.4
The action to take for packets that do not match any filter entries. the values default(3), and nat(5) are not allowed.
Status: current	Access: read-create
OBJECT-TYPE
	TFilterAction

tmnxLogFilterInUse		1.3.6.1.4.1.6527.3.1.2.12.6.1.5
When tmnxLogFilterInUse has a value of 'true', this filter is attached to a log file configuration. The same tmnxLogFilterEntry can be attached to more than one log file.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

tmnxLogFilterParamsTable		1.3.6.1.4.1.6527.3.1.2.12.7
A table of all log filter match entries for all log filters.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TmnxLogFilterParamsEntry

tmnxLogFilterParamsEntry		1.3.6.1.4.1.6527.3.1.2.12.7.1
Information about a particular Log Filter Parameter entry. Every Log Filter can have zero or more Log Filter Parameter match entries. The Log Filter parameter entries are checked in ascending order by their index value, tmnxLogFilterParamsIndex. Upon the first successful match, the specified actions are applied as indicated by the value of tmnxLogFilterParamsAction. No further checking against remaining tmnxLogFilterParamsEntry rows is done. Therefore, entries in this table should be sequenced from most to least explicit match criterion. It is recommended that multiple parameter entries for a log filter should be created with gaps between their index values. This allows a new entry to be inserted into an existing filter policy without needing to renumber the already existing filter parameters entries. A log filter entry in the tmnxLogFilterTable with no entry in the tmnxLogFilterParamsTable to define its match criteria set will match every log event, and the default action specified by tmnxLogFilterDefaultAction will be taken. Entries are created by user. Entries are deleted by user. There is no StorageType object, entries have a presumed StorageType of nonVolatile.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxLogFilterParamsEntry

tmnxLogFilterParamsIndex		1.3.6.1.4.1.6527.3.1.2.12.7.1.1
Tok_String
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxLogFilterEntryId

tmnxLogFilterParamsRowStatus		1.3.6.1.4.1.6527.3.1.2.12.7.1.2
Row Status for this Log filter's parameter entry.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

tmnxLogFilterParamsDescription		1.3.6.1.4.1.6527.3.1.2.12.7.1.3
The value of tmnxLogFilterParamsDescription is a user provided description string for this log filter match entry. It can consist of any printable, seven-bit ASCII characters up to 80 characters in length.
Status: current	Access: read-create
OBJECT-TYPE
	TItemDescription

tmnxLogFilterParamsAction		1.3.6.1.4.1.6527.3.1.2.12.7.1.4
the action to take for log events that match this filter entry. the value default(3) is allowed. If tmnxLogFilterParamsAction has the value 'default', the action specified by the value of tmnxLogFilterDefaultAction is applied to events that match this filter entry. The value nat(5) is not allowed.
Status: current	Access: read-create
OBJECT-TYPE
	TFilterActionOrDefault

tmnxLogFilterParamsApplication		1.3.6.1.4.1.6527.3.1.2.12.7.1.5
Matches log events with the specified application name. An application is the software entity the reports the log event and includes IP, MPLS, OSPF, CLI, SERVICES, etc.
Status: current	Access: read-create
OBJECT-TYPE
	TNamedItemOrEmpty

tmnxLogFilterParamsApplOperator		1.3.6.1.4.1.6527.3.1.2.12.7.1.6
The value of tmnxLogFilterParamsApplOperator is the comparison operator to use to determine if the log event matches the value of tmnxLogFilterParamsApplication. The only valid values from TmnxLogFilterOperator are 'off', 'equal', and 'notEqual'.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxLogFilterOperator

tmnxLogFilterParamsNumber		1.3.6.1.4.1.6527.3.1.2.12.7.1.7
The value of tmnxLogFilterParamsNumber is the log event number to be matched. Event numbers uniquely identify a certain event within an application but not across applications.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxEventNumber

tmnxLogFilterParamsNumberOperator		1.3.6.1.4.1.6527.3.1.2.12.7.1.8
The value of tmnxLogFilterParamsNumberOperator is the comparison operator to use to determine if the log event matches the value of tmnxLogFilterParamsNumber.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxLogFilterOperator

tmnxLogFilterParamsSeverity		1.3.6.1.4.1.6527.3.1.2.12.7.1.9
The value of tmnxLogFilterParamsSeverity is the log event severity level to be matched.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxPerceivedSeverity

tmnxLogFilterParamsSeverityOperator		1.3.6.1.4.1.6527.3.1.2.12.7.1.10
The value of tmnxLogFilterParamsSeverityOperator is the comparison operator to use to determine if the log event matches the value of tmnxLogFilterParamsSeverity.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxLogFilterOperator

tmnxLogFilterParamsSubject		1.3.6.1.4.1.6527.3.1.2.12.7.1.11
The value of tmnxLogFilterParamsSubject is the log event subject string to be matched. The subject is the entity that the event is reported for, such as a port ID.
Status: current	Access: read-create
OBJECT-TYPE
	TNamedItemOrEmpty

tmnxLogFilterParamsSubjectOperator		1.3.6.1.4.1.6527.3.1.2.12.7.1.12
The value of tmnxLogFilterParamsSubjectOperator is the comparison operator to use to determine if the log event matches the value of tmnxLogFilterParamsSubject. The only valid values of TmnxLogFilterOperator to use for the subject string comparison are 'off', 'equal', and 'notEqual'.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxLogFilterOperator

tmnxLogFilterParamsSubjectRegexp		1.3.6.1.4.1.6527.3.1.2.12.7.1.13
The value of tmnxLogFilterParamsSubjectRegexp specifies the type of string comparison to use to determine if the log event matches the value of tmnxLogFilterParamsSubject. When the value of tmnxLogFilterParamsSubjectRegexp is 'true', the string in tmnxLogFilterParamsSubject is a regular expression string to be matched against the subject string in the log event being filtered. When it has a value of 'false', the string in tmnxLogFilterParamsSubject is matched exactly by the event filter.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

tmnxLogFilterParamsRouter		1.3.6.1.4.1.6527.3.1.2.12.7.1.14
The value of tmnxLogFilterParamsRouter is the log event router context name string to be matched.
Status: current	Access: read-create
OBJECT-TYPE
	TNamedItemOrEmpty

tmnxLogFilterParamsRouterOperator		1.3.6.1.4.1.6527.3.1.2.12.7.1.15
The value of tmnxLogFilterParamsRouterOperator is the comparison operator to use to determine if the log event matches the value of tmnxLogFilterParamsRouter. The only valid values of TmnxLogFilterOperator to use for the router name string comparison are 'off', 'equal', and 'notEqual'.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxLogFilterOperator

tmnxLogFilterParamsRouterRegexp		1.3.6.1.4.1.6527.3.1.2.12.7.1.16
The value of tmnxLogFilterParamsRouterRegexp specifies the type of string comparison to use to determine if the log event matches the value of tmnxLogFilterParamsRouter. When the value of tmnxLogFilterParamsRouterRegexp is 'true', the string in tmnxLogFilterParamsRouter is a regular expression string to be matched against the router name string in the log event being filtered. When it has a value of 'false', the string in tmnxLogFilterParamsRouter is matched exactly by the event filter.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

tmnxSyslogTargetTable		1.3.6.1.4.1.6527.3.1.2.12.8
A table of all remote syslog collectors that this agent is configured to send syslog messages to.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TmnxSyslogTargetEntry

tmnxSyslogTargetEntry		1.3.6.1.4.1.6527.3.1.2.12.8.1
Information about a particular Syslog Target entry. Entries are created by user. Entries are deleted by user. There is no StorageType object, entries have a presumed StorageType of nonVolatile.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxSyslogTargetEntry

tmnxSyslogTargetIndex		1.3.6.1.4.1.6527.3.1.2.12.8.1.1
The value of tmnxSyslogTargetIndex is a unique arbitrary identifier for this syslog collector target.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxSyslogId

tmnxSyslogTargetRowStatus		1.3.6.1.4.1.6527.3.1.2.12.8.1.2
The tmnxSyslogTargetRowStatus object allows for dynamic creation and deletion of row entries in the tmnxSyslogTargetTable as well as the activation and deactivation of these entries. When this object's value is set to 'notInService (2)', no messages will be sent to this target collector and none of its counters will be incremented. Refer to the RowStatus convention for further details on the behavior of this object.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

tmnxSyslogTargetDescription		1.3.6.1.4.1.6527.3.1.2.12.8.1.3
The value of tmnxSyslogTargetDescription is an administratively assigned textual description of this syslog collector target.
Status: current	Access: read-create
OBJECT-TYPE
	TItemDescription

tmnxSyslogTargetAddress		1.3.6.1.4.1.6527.3.1.2.12.8.1.4
The value of tmnxSyslogTargetAddress is the IPv4 address for this syslog message collector target. If the value of this object is '0.0.0.0', then no messages will be sent, nor will any counters be incremented. This object was made obsolete in release 5.0. It is replaced by the InetAddress pair tmnxSyslogTargetAddrType and tmnxSyslogTargetAddr.
Status: obsolete	Access: read-create
OBJECT-TYPE
	IpAddress

tmnxSyslogTargetUdpPort		1.3.6.1.4.1.6527.3.1.2.12.8.1.5
The value of tmnxSyslogTargetUdpPort is the UDP port number that is used to send messages to this syslog collector target.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxUdpPort

tmnxSyslogTargetFacility		1.3.6.1.4.1.6527.3.1.2.12.8.1.6
The value of tmnxSyslogTargetFacility is the syslog facility number that will be encoded in messages sent to this syslog collector target.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxSyslogFacility

tmnxSyslogTargetSeverity		1.3.6.1.4.1.6527.3.1.2.12.8.1.7
The value of tmnxSyslogTargetSeverity is the maximum severity level of the messages that SHOULD be forwarded to this syslog collector target. The higher the level, the lower the severity.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxSyslogSeverity

tmnxSyslogTargetMessagePrefix		1.3.6.1.4.1.6527.3.1.2.12.8.1.8
The value of tmnxSyslogTargetMessagePrefix is a string of ABNF alphanumeric characters to be prepended as the MSG TAG to the syslog MSG CONTENT string and separated from it with a colon and space, ': '.
Status: current	Access: read-create
OBJECT-TYPE
	TNamedItemOrEmpty

tmnxSyslogTargetMessagesDropped		1.3.6.1.4.1.6527.3.1.2.12.8.1.9
The value of tmnxSyslogTargetMessagesDropped is a count of messages not sent to this syslog collector target because the severity level of the message was above tmnxSyslogTargetSeverity; the higher the level, the lower the severity.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

tmnxSyslogTargetAddrType		1.3.6.1.4.1.6527.3.1.2.12.8.1.10
The value of tmnxSyslogTargetAddrType specifies the type of host address to be used for the syslog message collector target. This object indicates the type of address stored in the corresponding tmnxSyslogTargetAddr object. Only 'ipv4', 'ipv6', and 'ipv6z' address types are supported.
Status: current	Access: read-create
OBJECT-TYPE
	InetAddressType

tmnxSyslogTargetAddr		1.3.6.1.4.1.6527.3.1.2.12.8.1.11
The value of tmnxSyslogTargetAddr specifies the IP host address to be used for the syslog message collector target. If no address is specified, ''H, then no messages will be sent nor will any counters be incremented. The syslog target address type is determined by the value of the corresponding tmnxSyslogTargetAddrType object.
Status: current	Access: read-create
OBJECT-TYPE
	InetAddress	Size(0|4|16|20)

tmnxEventAppTable		1.3.6.1.4.1.6527.3.1.2.12.9
A table of all applications that generate TiMOS logger events.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TmnxEventAppEntry

tmnxEventAppEntry		1.3.6.1.4.1.6527.3.1.2.12.9.1
Information about a particular application entry. Entries are created by the agent when the system initializes. There is no StorageType object, entries have a presumed StorageType of permanent.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxEventAppEntry

tmnxEventAppIndex		1.3.6.1.4.1.6527.3.1.2.12.9.1.1
The value of tmnxEventAppIndex is a unique arbitrary identifier for this application event generator.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

tmnxEventAppName		1.3.6.1.4.1.6527.3.1.2.12.9.1.2
The value of tmnxEventAppName is the name string that is used in TiMOS log messages as the application that generated the logged event.
Status: current	Access: read-only
OBJECT-TYPE
	TNamedItem

tmnxEventTable		1.3.6.1.4.1.6527.3.1.2.12.10
A table of all TiMOS events that can be generated.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TmnxEventEntry

tmnxEventEntry		1.3.6.1.4.1.6527.3.1.2.12.10.1
Information about a particular TiMOS event type entry. Entries are created by the agent when the system initializes. There is no StorageType object, entries have a presumed StorageType of permanent.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxEventEntry

tmnxEventID		1.3.6.1.4.1.6527.3.1.2.12.10.1.1
The value of tmnxEventID is a unique arbitrary identifier for indexing event type entries within an event generator application as identified by the value of tmnxEventAppIndex.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

tmnxEventName		1.3.6.1.4.1.6527.3.1.2.12.10.1.2
The value of tmnxEventName is a short name string used to describe this event type.
Status: current	Access: read-only
OBJECT-TYPE
	TNamedItem

tmnxEventSeverity		1.3.6.1.4.1.6527.3.1.2.12.10.1.3
The value of tmnxEventSeverity indicates the severity level that will be associated with this type of event when it is generated.
Status: current	Access: read-write
OBJECT-TYPE
	TmnxPerceivedSeverity

tmnxEventControl		1.3.6.1.4.1.6527.3.1.2.12.10.1.4
The value of tmnxEventControl determines whether or not events of this type will be generated or suppressed. When it has a value of 'true', the event is generated and tmnxEventCounter is incremented. When it has a value of 'false', the event is suppressed and tmnxEventDropCount is incremented.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

tmnxEventCounter		1.3.6.1.4.1.6527.3.1.2.12.10.1.5
The value of tmnxEventCounter is the number of times an event of this type has been generated.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

tmnxEventDropCount		1.3.6.1.4.1.6527.3.1.2.12.10.1.6
The value of tmnxEventDropCount is the number of times and event of this type has been suppressed because tmnxEventControl is set to 'false'. When tmnxEventControl is set to 'true', tmnxEventDropCount indicates the number of events dropped because of logger input queue size overrun or dropped because of throttling when tmnxEventThrottle is set to 'true'.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

tmnxEventReset		1.3.6.1.4.1.6527.3.1.2.12.10.1.7
Setting tmnxEventReset to 'doAction (1)' causes the agent to reset the values of tmnxEventSeverity and tmnxEventControl to the default values for this event type.
Status: current	Access: read-write
OBJECT-TYPE
	TmnxActionType

tmnxEventThrottle		1.3.6.1.4.1.6527.3.1.2.12.10.1.8
The value of tmnxEventThrottle determines whether or not events of this type will be throttled. When it has a value of 'true', the event is throttled at the rate indicated by the value of tmnxEventThrottleLimit and tmnxEventThrottleInterval. When it has a value of 'false', no event throttling is applied.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

tmnxSnmpTrapGroupTable		1.3.6.1.4.1.6527.3.1.2.12.11
A table of all remote SNMP trap collectors to which this agent is configured to send SNMP notifications messages. This table was made obsolete in the 5.0 release and is replace with tmnxSnmpTrapDestTable.
Status: obsolete	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TmnxSnmpTrapGroupEntry

tmnxSnmpTrapGroupEntry		1.3.6.1.4.1.6527.3.1.2.12.11.1
Information about a particular SNMP trap destination entry. The first index instance creates and snmp trap group to be associated with the event log with the same value for tmnxLogIdIndex. The second and third indexes specify a remote SNMP trap destination that will be sent SNMP notification messages from the associated event log. Entries are created by user. Entries are deleted by user. There is no StorageType object, entries have a presumed StorageType of nonVolatile. This table was made obsolete in the 5.0 release and is replaced with the tmnxSnmpTrapDestTable.
Status: obsolete	Access: not-accessible
OBJECT-TYPE
	TmnxSnmpTrapGroupEntry

tmnxStgIndex		1.3.6.1.4.1.6527.3.1.2.12.11.1.1
The value of tmnxStgIndex specifies an snmp trap group to be associated with the event log with the same value for tmnxLogIdIndex. This object was made obsolete in the 5.0 release. It is replaced by tmnxStdIndex.
Status: obsolete	Access: not-accessible
OBJECT-TYPE
	TmnxLogIdIndex

tmnxStgDestAddress		1.3.6.1.4.1.6527.3.1.2.12.11.1.2
The value of tmnxStgDestAddress is the IPv4 address for this remote snmp notification destination. If the value of this object is '0.0.0.0', then no messages will be sent, nor will any counters be incremented. This object was made obsolete in the 5.0 release. It is replaced by the InetAddressType/InetAddress objects tmnxStdDestAddrType and tmnxStdDestAddr.
Status: obsolete	Access: not-accessible
OBJECT-TYPE
	IpAddress

tmnxStgDestPort		1.3.6.1.4.1.6527.3.1.2.12.11.1.3
The value of tmnxStgDestPort is the UDP port number that is used to send messages to this remote SNMP notification destination. This object was made obsolete in the 5.0 release. It is replaced by tmnxStdDestPort.
Status: obsolete	Access: not-accessible
OBJECT-TYPE
	TmnxUdpPort

tmnxStgRowStatus		1.3.6.1.4.1.6527.3.1.2.12.11.1.4
The tmnxStgRowStatus object allows for dynamic creation and deletion of row entries in the tmnxSnmpTrapGroupTable as well as the activation and deactivation of these entries. When this object's value is set to 'notInService (2)', no messages will be sent to this snmp trap group and none of its counters will be incremented. Refer to the RowStatus convention for further details on the behavior of this object. This object was made obsolete in the 5.0 release. It is replaced by tmnxStdRowStatus.
Status: obsolete	Access: read-create
OBJECT-TYPE
	RowStatus

tmnxStgDescription		1.3.6.1.4.1.6527.3.1.2.12.11.1.5
The value of tmnxStgDescription is an administratively assigned textual description of this snmp trap destination. This object was made obsolete in the 5.0 release. It is replaced by tmnxStdDescription.
Status: obsolete	Access: read-create
OBJECT-TYPE
	TItemDescription

tmnxStgVersion		1.3.6.1.4.1.6527.3.1.2.12.11.1.6
The value of tmnxStgVersion specifies the SNMP version that will be used to format notification messages sent to this snmp trap destination. The values supported by the Alcatel-Lucent SROS series SNMP agent are: 0 for SNMPv1 1 for SNMPv2c 3 for SNMPv3 This object was made obsolete in the 5.0 release. It is replaced by tmnxStdVersion.
Status: obsolete	Access: read-create
OBJECT-TYPE
	SnmpMessageProcessingModel

tmnxStgNotifyCommunity		1.3.6.1.4.1.6527.3.1.2.12.11.1.7
The value of tmnxStgNotifyCommunity specifies the SNMPv1 or SNMPv2c community name string or the SNMPv3 security name used when an SNMP notification message is sent to this trap destination. If the value of this object is the empty string, then no messages will be sent nor will any counters be incremented. This object was made obsolete in the 5.0 release. It is replaced by tmnxStdVersion.
Status: obsolete	Access: read-create
OBJECT-TYPE
	OCTET STRING	Size(0..32)

tmnxStgSecurityLevel		1.3.6.1.4.1.6527.3.1.2.12.11.1.8
The value of tmnxStgSecurityLevel specifies the level of security at which SNMP notification messages will be sent to the SNMP trap destination when tmnxStgVersion has a value of '3' for SNMPv3. This object was made obsolete in the 5.0 release. It is replaced by tmnxStdSecurityLevel.
Status: obsolete	Access: read-create
OBJECT-TYPE
	SnmpSecurityLevel

tmnxEventTest		1.3.6.1.4.1.6527.3.1.2.12.12
Setting tmnxEventTest to 'doAction' causes the tmnxTestEvent notification to be generated.
Status: current	Access: read-write
OBJECT-TYPE
	TmnxActionType

tmnxEventThrottleLimit		1.3.6.1.4.1.6527.3.1.2.12.13
The value of tmnxEventThrottleLimit specifies the number of log events that can be logged within the tmnxEventThrottleInterval for a specific entry in the tmnxEventTable. Once the limit has been reached, any additional events of that type will be dropped, i.e. tmnxEventDropCount will be incremented. At the end of the throttle interval if any events have been dropped a tmnxLogEventThrottled notification will be sent.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	1..20000

tmnxEventThrottleInterval		1.3.6.1.4.1.6527.3.1.2.12.14
The value of tmnxEventThrottleInterval specifies the number of seconds that an event throttling interval lasts.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	1..1200

tmnxSnmpSetErrsMax		1.3.6.1.4.1.6527.3.1.2.12.15
The value of tmnxSnmpSetErrsMax indicates the maximum number of entries the agent will create in the tmnxSnmpSetErrsTable. Once the table is full the agent will delete the oldest entry in the table in order to add new entries.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

tmnxSnmpSetErrsTable		1.3.6.1.4.1.6527.3.1.2.12.16
A table of recent SNMP SET failures. Only the SET errs from remote SNMP manager requests are saved in this table. Only SET errs detected by the SNMP engine in the test phase consistency check method functions are saved. SET errors that are caught by the preliminary access and ASN.1 decoding phase are not saved. These are errs such as noAccess, notWritable, wrongType, wrongLength and wrongEncoding. Note that notWritable, wrongType, and wrongLength errs may sometimes be generated by the consistency check; in this case they will be saved in this table. SET errs caused by local CLI sessions are not saved. The tmnxSnmpSetErrsTable is intended to provide an aide to Network Management Systems (NMS) developers. When an SNMP SET fails during the consistency checking test phase, this table may provide more detailed failure reason information than the simple SNMP error code value in the SNMP response PDU.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TmnxSnmpSetErrsEntry

tmnxSnmpSetErrsEntry		1.3.6.1.4.1.6527.3.1.2.12.16.1
Information about a particular SNMP SET error. The first two index instances identify the SNMP manager who sent the SNMP SET request that failed. The third index specifies the SNMP request-id (sequence number) of the SNMP SET request that failed. Entries are created by the agent. Entries are deleted by the agent. There is no StorageType object, entries have a presumed StorageType of volatile.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxSnmpSetErrsEntry

tmnxSseAddressType		1.3.6.1.4.1.6527.3.1.2.12.16.1.1
The value of tmnxSseAddressType indicates the IP address type of address specified in tmnxSseAddress. 'ipv4' and 'ipv6' are the only address type values supported.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddressType

tmnxSseAddress		1.3.6.1.4.1.6527.3.1.2.12.16.1.2
The value of tmnxSseAddress is the IP address of the SNMP manager that sent the SNMP SET request that failed for this error reason.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddress	Size(4|16)

tmnxSseSnmpPort		1.3.6.1.4.1.6527.3.1.2.12.16.1.3
The value of tmnxSseSnmpPort is the UDP port number of the SNMP manager that sent the SNMP SET request that failed for this error reason.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxUdpPort

tmnxSseRequestId		1.3.6.1.4.1.6527.3.1.2.12.16.1.4
The value of tmnxSseRequestId indicates the request-id of the SNMP SNMP SET request that failed for this error reason.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

tmnxSseVersion		1.3.6.1.4.1.6527.3.1.2.12.16.1.5
The value of tmnxSseVersion indicates the SNMP version of the SNMP SET request that failed. The values supported by the Alcatel-Lucent SROS series SNMP agent are: 0 for SNMPv1 1 for SNMPv2c 3 for SNMPv3
Status: current	Access: read-only
OBJECT-TYPE
	SnmpMessageProcessingModel

tmnxSseSeverityLevel		1.3.6.1.4.1.6527.3.1.2.12.16.1.6
The value of tmnxSseSeverityLevel indicates severity level that is associated with this type SNMP SET error.
Status: current	Access: read-only
OBJECT-TYPE
	TmnxPerceivedSeverity

tmnxSseModuleId		1.3.6.1.4.1.6527.3.1.2.12.16.1.7
The value of tmnxSseModuleId indicates a unique arbitrary identified for the TiMOS application module that generated this SNMP SET error. NOTE: This is NOT the same value used for tmnxEventAppIndex.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

tmnxSseModuleName		1.3.6.1.4.1.6527.3.1.2.12.16.1.8
The value of tmnxSseModuleName indicates the name string of the TiMOS application module that generated this SNMP SET error. NOTE: This is NOT the same value used for tmnxEventAppName.
Status: current	Access: read-only
OBJECT-TYPE
	TNamedItem

tmnxSseErrorCode		1.3.6.1.4.1.6527.3.1.2.12.16.1.9
The value of tmnxSseErrorCode indicates the error number associated with this SNMP SET error. The error numbers are unique within a tmnxSseModuleId. They are not unique across all modules so both the module name and error number are required to identify a particular error message.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

tmnxSseErrorName		1.3.6.1.4.1.6527.3.1.2.12.16.1.10
The value of tmnxSseErrorName indicates the error name associated with this SNMP SET error. The error names are unique within a tmnxSseModuleId. They are not unique across all modules so both the module name and error name are required to identify a particular error message.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..64)

tmnxSseErrorMsg		1.3.6.1.4.1.6527.3.1.2.12.16.1.11
The value of tmnxSseErrorMsg indicates the fixed error message text associated with this SNMP SET error identified by the values of tmnxSseModuleId and tmnxSseErrorCode.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..255)

tmnxSseExtraText		1.3.6.1.4.1.6527.3.1.2.12.16.1.12
The value of tmnxSseExtraText indicates the fixed run-time variable message text associated with this SNMP SET error identified by the values of tmnxSseModuleId and tmnxSseErrorCode. If the extra text was truncated to fit into buffer size allowed, the last character will be an asterix (*).
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..320)

tmnxSseTimestamp		1.3.6.1.4.1.6527.3.1.2.12.16.1.13
The value of tmnxSseTimestamp indicates the sysUpTime value when this tmnxSnmpSetErrsEntry was created by the agent.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

tmnxSnmpTrapLogTable		1.3.6.1.4.1.6527.3.1.2.12.17
A table of all remote SNMP trap logs to which this agent is configured to send SNMP notifications messages.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TmnxSnmpTrapLogEntry

tmnxSnmpTrapLogEntry		1.3.6.1.4.1.6527.3.1.2.12.17.1
Each row entry in the tmnxSnmpTrapLogTable represents additional columns for attributes specific to the Alcatel-Lucent SROS series implementation of SNMP-NOTIFICATION-MIB::snmpNotifyTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxSnmpTrapLogEntry

tmnxSnmpTrapLogDescription		1.3.6.1.4.1.6527.3.1.2.12.17.1.1
The value of tmnxSnmpTrapLogDescription is an administratively assigned textual description of this snmp trap log.
Status: current	Access: read-create
OBJECT-TYPE
	TItemDescription

tmnxSnmpTrapDestTable		1.3.6.1.4.1.6527.3.1.2.12.18
A table of all remote SNMP IPv4/v6 trap collectors to which this agent is configured to send SNMP notification messages.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TmnxSnmpTrapDestEntry

tmnxSnmpTrapDestEntry		1.3.6.1.4.1.6527.3.1.2.12.18.1
Information about a particular SNMP notification destination entry. The first index instance creates an snmp notification group to be associated with the event log with the same value for tmnxLogIdIndex. The second index specifies an administrative name to identify a specific SNMP notification target. Entries are created by user. Entries are deleted by user. There is no StorageType object, entries have a presumed StorageType of nonVolatile.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxSnmpTrapDestEntry

tmnxStdIndex		1.3.6.1.4.1.6527.3.1.2.12.18.1.1
The value of tmnxStdIndex specifies an snmp notification group to be associated with the event log with the same value for tmnxLogIdIndex.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxLogIdIndex

tmnxStdName		1.3.6.1.4.1.6527.3.1.2.12.18.1.2
The value of tmnxStdName specifies the name of an snmp notification destination within the snmp notification group specified by tmnxLogIdIndex.
Status: current	Access: not-accessible
OBJECT-TYPE
	SnmpAdminString	Size(1..28)

tmnxStdRowStatus		1.3.6.1.4.1.6527.3.1.2.12.18.1.3
The tmnxStdRowStatus object allows for dynamic creation and deletion of row entries in the tmnxSnmpTrapDestTable as well as the activation and deactivation of these entries. In order for 'createAndGo' row creation to succeed or status to transition to 'active' a value must be set for tmnxStdNotifyCommunity. In order for 'createAndGo' row creation to succeed or status to transition to 'active' an entry must exist in the SNMP-NOTIFICATION-MIB::snmpNotifyTable with an snmpNotifyName index that is the ASCII string representation of the value of tmnxStdIndex. When this object's value is set to 'notInService (2)', no messages will be sent to this snmp notification collector and none of its counters will be incremented. Refer to the RowStatus convention for further details on the behavior of this object.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

tmnxStdRowLastChanged		1.3.6.1.4.1.6527.3.1.2.12.18.1.4
The value of tmnxStdRowLastChanged indicates the sysUpTime when the value of a writable object in this row entry was modified.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

tmnxStdDestAddrType		1.3.6.1.4.1.6527.3.1.2.12.18.1.5
The value of tmnxStdDestAddrType specifies the type of host address to be used for the remote SNMP notification collector. This object indicates the type of address stored in the corresponding tmnxStdDestAddr object. If the value of this object is 'unknown', then no messages will be sent nor will any counters be incremented. If tmnxStdDestAddrType is not set in the same PDU with tmnxStdDestAddr, the set request will fail with an inconsistentValue error.
Status: current	Access: read-create
OBJECT-TYPE
	InetAddressType

tmnxStdDestAddr		1.3.6.1.4.1.6527.3.1.2.12.18.1.6
The value of tmnxStdDestAddr specifies the IP host address to be used for the remote SNMP notification collector. The SNMP notification collector IP address type is determined by the value of the corresponding tmnxStdDestAddrType object. If the value of this object is empty or all NULLs, then no messages will be sent nor will any counters be incremented. If tmnxStdDestAddrType is not set in the same PDU with tmnxStdDestAddr, the set request will fail with an inconsistentValue error.
Status: current	Access: read-create
OBJECT-TYPE
	InetAddress	Size(0|4|16|20)

tmnxStdDestPort		1.3.6.1.4.1.6527.3.1.2.12.18.1.7
The value of tmnxStdDestPort is the UDP port number that is used to send messages to this remote SNMP notification collector.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxUdpPort

tmnxStdDescription		1.3.6.1.4.1.6527.3.1.2.12.18.1.8
The value of tmnxStdDescription is an administratively assigned textual description of this SNMP notification collector.
Status: current	Access: read-create
OBJECT-TYPE
	TItemDescription

tmnxStdVersion		1.3.6.1.4.1.6527.3.1.2.12.18.1.9
The value of tmnxStdVersion specifies the SNMP version that will be used to format notification messages sent to this SNMP notification collector. The values supported by the Alcatel-Lucent SROS series SNMP agent are: 0 for SNMPv1 1 for SNMPv2c 3 for SNMPv3
Status: current	Access: read-create
OBJECT-TYPE
	SnmpMessageProcessingModel

tmnxStdNotifyCommunity		1.3.6.1.4.1.6527.3.1.2.12.18.1.10
The value of tmnxStdNotifyCommunity specifies the SNMPv1 or SNMPv2c community name string or the SNMPv3 security name used when an SNMP notification message is sent to this SNMP notification collector. If the value of this object is the empty string, then no messages will be sent nor will any counters be incremented.
Status: current	Access: read-create
OBJECT-TYPE
	OCTET STRING	Size(0..31)

tmnxStdSecurityLevel		1.3.6.1.4.1.6527.3.1.2.12.18.1.11
The value of tmnxStdSecurityLevel specifies the level of security at which SNMP notification messages will be sent to the SNMP notification collector when tmnxStdVersion has a value of '3' for SNMPv3.
Status: current	Access: read-create
OBJECT-TYPE
	SnmpSecurityLevel

tmnxStdReplay		1.3.6.1.4.1.6527.3.1.2.12.18.1.12
The value of tmnxStdReplay specifies whether or not to resend notifications that were generated while this notification destination did not have a route installed for it in the route tables.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

tmnxStdReplayStart		1.3.6.1.4.1.6527.3.1.2.12.18.1.13
The value of tmnxStdReplayStart indicates the SNMP notification request ID of the first event that cound not be generated because there is no route to this notification target address. Events will be resent when this notification target address is readded to the route tables, on either an in-band or out-of-band interface. The agent searches backwards in the event log and begins resending events from the oldest event that has a timestamp <= 5 hundredths of a second less than the timestamp of the event with this request ID. Note that if the outage is long and a large number of events are generated in the meantime, it is possible that the log memory storage has wrapped and the event data for this request ID is no longer available. In that case, the oldest event saved in the log will be the first event resent. A value of 0 indicates that there are no missed events waiting to be resent.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

tmnxStdReplayLastTime		1.3.6.1.4.1.6527.3.1.2.12.18.1.14
The value of tmnxStdReplayLastTime indicates the sysUpTime when missed events were last replayed to this SNMP notification target address. A value of 0 indicates that no missed events have been replayed to this SNMP notification target address.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

tmnxStdMaxTargets		1.3.6.1.4.1.6527.3.1.2.12.19
The maximum number of tmnxSnmpTrapDestTable row entries that can be created for a specific tmnxStdIndex that represents an snmp notification group.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	10..100

tmnxLogApCustRecordTable		1.3.6.1.4.1.6527.3.1.2.12.20
The Alcatel-Lucent SROS series tmnxLogApCustRecordTable augments tmnxLogApTable. The table allows to configure the layout and setting for a custom accounting record associated with this accounting policy.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TmnxLogApCustRecordEntry

tmnxLogApCustRecordEntry		1.3.6.1.4.1.6527.3.1.2.12.20.1
Defines an entry in the tmnxLogApCustRecordTable. Entries in this table are created and destroyed via SNMP Set requests to the tmnxLogApRowStatus object of the tmnxLogApTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxLogApCustRecordEntry

tmnxLogApCrLastChanged		1.3.6.1.4.1.6527.3.1.2.12.20.1.1
The value of tmnxLogApCrLastChanged indicates the sysUpTime when an object in this table was last modified. A Value 0 means that no change was made to this row since the box was last initialized.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

tmnxLogApCrSignChangeDelta		1.3.6.1.4.1.6527.3.1.2.12.20.1.2
The value of tmnxLogApCrSignChangeDelta specifies the delta change (significant change) that is required for the custom record to be written to the xml file.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

tmnxLogApCrSignChangeQueue		1.3.6.1.4.1.6527.3.1.2.12.20.1.3
The value of tmnxLogApCrSignChangeQueue specifies the reference queue to which the significant change defined in tmnxLogApCrSignChangeDelta applies.
Status: current	Access: read-write
OBJECT-TYPE
	TQueueIdOrAll

tmnxLogApCrSignChangeOCntr		1.3.6.1.4.1.6527.3.1.2.12.20.1.4
The value of tmnxLogApCrSignChangeOCntr specifies the counter-id that will be taken as reference to which the significant change defined in tmnxLogApCrSignChangeDelta applies.
Status: current	Access: read-write
OBJECT-TYPE
	THsmdaCounterIdOrZeroOrAll

tmnxLogApCrSignChangeQICounters		1.3.6.1.4.1.6527.3.1.2.12.20.1.5
The value of tmnxLogApCrSignChangeQICounters specifies the ingress counter Ids in the queue defined by tmnxLogApCrSignChangeQueue to be taken as reference to which the significant change defined in tmnxLogApCrSignChangeDelta applies. A non-zero value of this object is only allowed if the object tmnxLogApCrSignChangeQueue has a non-zero value.
Status: current	Access: read-write
OBJECT-TYPE
	TmnxAccPlcyQICounters

tmnxLogApCrSignChangeQECounters		1.3.6.1.4.1.6527.3.1.2.12.20.1.6
The value of tmnxLogApCrSignChangeQECounters specifies the egress counter Ids in the queue defined by tmnxLogApCrSignChangeQueue to be taken as reference to which the significant change defined in tmnxLogApCrSignChangeDelta applies. A non-zero value of this object is only allowed if the object tmnxLogApCrSignChangeQueue has a non-zero value.
Status: current	Access: read-write
OBJECT-TYPE
	TmnxAccPlcyQECounters

tmnxLogApCrSignChangeOICounters		1.3.6.1.4.1.6527.3.1.2.12.20.1.7
The value of tmnxLogApCrSignChangeOICounters specifies the ingress counter Ids in the counter-group defined by tmnxLogApCrSignChangeOCntr to be taken as reference to which the significant change defined in tmnxLogApCrSignChangeDelta applies. A non-zero value of this object is only allowed if the object tmnxLogApCrSignChangeOCntr has a non-zero value.
Status: current	Access: read-write
OBJECT-TYPE
	TmnxAccPlcyOICounters

tmnxLogApCrSignChangeOECounters		1.3.6.1.4.1.6527.3.1.2.12.20.1.8
The value of tmnxLogApCrSignChangeOECounters specifies the egress counter Ids in the counter-group defined by tmnxLogApCrSignChangeOCntr to be taken as reference to which the significant change defined in tmnxLogApCrSignChangeDelta applies. A non-zero value of this object is only allowed if the object tmnxLogApCrSignChangeOCntr has a non-zero value.
Status: current	Access: read-write
OBJECT-TYPE
	TmnxAccPlcyOECounters

tmnxLogApCrSignChangeAACounters		1.3.6.1.4.1.6527.3.1.2.12.20.1.9
The value of tmnxLogApCrSignChangeAACounters specifies the AA (Application assurance) counter Ids to be taken as reference to which the significant change defined in tmnxLogApCrSignChangeDelta applies. A non-zero value of this object is only allowed if both the objects tmnxLogApCrSignChangeOCntr and tmnxLogApCrSignChangeQueue are zero. Also, a non-zero value for this object is only allowed if the object tmnxLogApCrSignChangeDelta is either 0 or 1.
Status: current	Access: read-write
OBJECT-TYPE
	TmnxAccPlcyAACounters

tmnxLogApCrAACounters		1.3.6.1.4.1.6527.3.1.2.12.20.1.10
The value of tmnxLogApCrQueueECounters indicates the list of AA (application Assurance) counters that need to be collected in this custom record.
Status: current	Access: read-write
OBJECT-TYPE
	TmnxAccPlcyAACounters

tmnxLogApCustRecordQueueTable		1.3.6.1.4.1.6527.3.1.2.12.21
The Alcatel-Lucent SROS series tmnxLogApCustRecordQueueTable allows to create custom record queue information for a given accounting policy. Rows can only be created for existing accounting policies (as defined in tmnxLogApTable).
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TmnxLogApCustRecordQueueEntry

tmnxLogApCustRecordQueueEntry		1.3.6.1.4.1.6527.3.1.2.12.21.1
Defines an entry in the tmnxLogApCustRecordQueueTable. Entries in this table are created and destroyed via SNMP Set requests.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxLogApCustRecordQueueEntry

tmnxLogApCrQueueId		1.3.6.1.4.1.6527.3.1.2.12.21.1.1
The value of tmnxLogApCrQueueId specifies the queue-id for which counters will be collected in this custom record. The counters that will be collected are defined in tmnxLogApCrQueueICounters and tmnxLogApCrQueueECounters.
Status: current	Access: not-accessible
OBJECT-TYPE
	TQueueId	1..32

tmnxLogApCrQueueRowStatus		1.3.6.1.4.1.6527.3.1.2.12.21.1.2
Row Status of the entry. This allows creation/deletion of rows in this table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

tmnxLogApCrQueueLastChanged		1.3.6.1.4.1.6527.3.1.2.12.21.1.3
The value of tmnxLogApCrQueueLastChanged indicates the sysUpTime when an object in this table was last modified. A Value 0 means that no change was made to this row since it was created.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

tmnxLogApCrQueueICounters		1.3.6.1.4.1.6527.3.1.2.12.21.1.4
The value of tmnxLogApCrQueueICounters indicates the list of ingress counters that need to be collected in this custom record. At least one of the objects tmnxLogApCrQueueICounters or tmnxLogApCrQueueECounters must have a non-zero value.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxAccPlcyQICounters

tmnxLogApCrQueueECounters		1.3.6.1.4.1.6527.3.1.2.12.21.1.5
The value of tmnxLogApCrQueueECounters indicates the list of egress counters that need to be collected in this custom record. At least one of the objects tmnxLogApCrQueueICounters or tmnxLogApCrQueueECounters must have a non-zero value.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxAccPlcyQECounters

tmnxLogApCrOverrideCntrTable		1.3.6.1.4.1.6527.3.1.2.12.22
The Alcatel-Lucent SROS series tmnxLogApCrOverrideCntrTable allows to create custom record counter override information for a given accounting policy. Rows can only be created for existing accounting policies (as defined in tmnxLogApTable).
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TmnxLogApCrOverrideCntrEntry

tmnxLogApCrOverrideCntrEntry		1.3.6.1.4.1.6527.3.1.2.12.22.1
Defines an entry in the tmnxLogApCrOverrideCntrTable. Entries in this table are created and destroyed via SNMP Set requests.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxLogApCrOverrideCntrEntry

tmnxLogApCrOverrideCntrId		1.3.6.1.4.1.6527.3.1.2.12.22.1.1
The value of tmnxLogApCrOverrideCntrId specifies the counter group for which counters will be collected in this custom record. The counters that will be collected are defined in tmnxLogApCrOverrideCntrICounters and tmnxLogApCrOverrideCntrECounters.
Status: current	Access: not-accessible
OBJECT-TYPE
	THsmdaCounterIdOrZero	1..8

tmnxLogApCrOverrideCntrRowStatus		1.3.6.1.4.1.6527.3.1.2.12.22.1.2
Row Status of the entry. This allows creation/deletion of rows in this table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

tmnxLogApCrOverrideCntrLastChngd		1.3.6.1.4.1.6527.3.1.2.12.22.1.3
The value of tmnxLogApCrOverrideCntrLastChngd indicates the sysUpTime when an object in this table was last modified. A Value 0 means that no change was made to this row since it was created.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

tmnxLogApCrOverrideCntrICounters		1.3.6.1.4.1.6527.3.1.2.12.22.1.4
The value of tmnxLogApCrOverrideCntrICounters indicates the list of ingress counters that need to be collected in this custom record. At least one of the objects tmnxLogApCrOverrideCntrICounters or tmnxLogApCrOverrideCntrECounters must have a non-zero value.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxAccPlcyOICounters

tmnxLogApCrOverrideCntrECounters		1.3.6.1.4.1.6527.3.1.2.12.22.1.5
The value of tmnxLogApCrOverrideCntrECounters indicates the list of egress counters that need to be collected in this custom record. At least one of the objects tmnxLogApCrOverrideCntrICounters or tmnxLogApCrOverrideCntrECounters must have a non-zero value.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxAccPlcyOECounters

tmnxEventPrimaryRoutePref		1.3.6.1.4.1.6527.3.1.2.12.23
The value of tmnxEventPrimaryRoutePref specifies the primary routing preference for traffic generated for SNMP notifications and syslog messages. A value of 'inband' specifies that the Logging utility will attempt to use the Base routing context to send SNMP notifications and syslog messages to remote destinations. A value of 'outband' specifies that the Logging utility will attempt to use the management routing context to send SNMP notifications and syslog messages to remote destinations. If the remote destination, as specified by tmnxStdDestAddr or tmnxSyslogTargetAddr, is not reachable via the routing context specified by tmnxEventPrimaryRoutePref, the secondary routing preference as specified by tmnxEventSecondaryRoutePref will be attempted.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	inband(1), outband(2)

tmnxEventSecondaryRoutePref		1.3.6.1.4.1.6527.3.1.2.12.24
The value of tmnxEventSecondaryRoutePref specifies the secondary routing preference for traffic generated for SNMP notifications and syslog messages. The routing context specified by the tmnxEventSecondaryRoutePref will be attempted if the remote destination was not reachable by the primary routing preference, specified by tmnxEventPrimaryRoutePref. The value specified for tmnxEventSecondaryRoutePref must be distinct from the value for tmnxEventPrimaryRoutePref. A value of 'inband' specifies that the Logging utility will attempt to use the Base routing context to send SNMP notifications and syslog messages to remote destinations. A value of 'outband' specifies that the Logging utility will attempt to use the management routing context to send SNMP notifications and syslog messages to remote destinations. A value of 'none' specifies that no attempt will be made to send SNMP notifications and syslog messages to remote destinations. If the remote destination, as specified by tmnxStdDestAddr or tmnxSyslogTargetAddr, is not reachable via the routing contexts specified by tmnxEventPrimaryRoutePref and tmnxEventSecondaryRoutePref, the Log utility will fail to send SNMP notifications and syslog messages to the remote destination.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	inband(1), outband(2), none(3)

tmnxLogConfigEventsDamped		1.3.6.1.4.1.6527.3.1.2.12.25
The value of tmnxLogConfigEventsDamped specifies whether or not the module generating tmnxConfigCreate, tmnxConfigDelete, and tmnxConfigModify events applies a damping algorithm. WARNING: While this event damping is original behavior for some modules such as service manager, QoS, and filters it can result in the NMS system database being out of sync because of missed change events. On the other hand, if the damping is disabled, 'false', it may take much longer for a large CLI configuration file to be processed when manually 'execed' after system bootup.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

tmnxLogEventHistoryObjs		1.3.6.1.4.1.6527.3.1.2.12.26
OBJECT IDENTIFIER

tmnxLogEventHistGeneralObjs		1.3.6.1.4.1.6527.3.1.2.12.26.1
OBJECT IDENTIFIER

tmnxLogExRbkOpTblLastChange		1.3.6.1.4.1.6527.3.1.2.12.26.1.1
The value of the object tmnxLogExRbkOpTblLastChange indicates the value of sysUpTime at the time of the last modification of a row entry in the tmnxLogExecRollbackOpTable.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

tmnxLogExRbkOpMaxEntries		1.3.6.1.4.1.6527.3.1.2.12.26.1.2
The value of the object tmnxLogExRbkOpMaxEntries specifies the maximum number of row entries supported in the tmnxLogExecRollbackOpTable.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	0..10

tmnxLogExecRollbackOpTable		1.3.6.1.4.1.6527.3.1.2.12.26.3
The Alcatel-Lucent SROS series tmnxLogExecRollbackOpTable provides a history of up to the last number of 'exec' or rollback revert operations specified by the value of tmnxLogExRbkOpMaxEntries. The tmnxLogExecRollbackOpTable is intended to provide an aide to Network Management Systems (NMS). The 'exec' of a large configuration file via the system's CLI or a large rollback revert operation will generate so many configuration change and other events in a short time that neither the SROS's event logging utility no the NMS can keep up with them. This results in either or both the SROS and NMS dropping events and requires the NMS to perform a costly resynchronization of its management database.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TmnxLogExecRollbackOpEntry

tmnxLogExecRollbackOpEntry		1.3.6.1.4.1.6527.3.1.2.12.26.3.1
Defines a row entry in the tmnxLogExecRollbackOpTable. Entries in this table are created and deleted by the agent.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxLogExecRollbackOpEntry

tmnxLogExRbkOpIndex		1.3.6.1.4.1.6527.3.1.2.12.26.3.1.1
The value of tmnxLogExRbkOpIndex is a unique value that indicates an instance of an exec or rollback revert operation. Only the most recent instances are kept in this table. The maximum number of row entries supported in this table is specified by the value of tmnxLogExRbkOpMaxEntries.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

tmnxLogExRbkOpLastChanged		1.3.6.1.4.1.6527.3.1.2.12.26.3.1.2
The value of tmnxLogExRbkOpLastChanged indicates the sysUpTime when an object in this table was last modified. A Value 0 means that no change was made to this row since it was created.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

tmnxLogExRbkOpType		1.3.6.1.4.1.6527.3.1.2.12.26.3.1.3
The value of tmnxLogExRbkOpType indicates the type of operation this row entry represents.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(0), exec(1), rollback(2)

tmnxLogExRbkOpStatus		1.3.6.1.4.1.6527.3.1.2.12.26.3.1.4
The value of tmnxLogExRbkOpStatus indicates the status of this exec or rollback revert operation.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(0), inProgress(1), success(2), failed(3)

tmnxLogExRbkOpBegin		1.3.6.1.4.1.6527.3.1.2.12.26.3.1.5
The value of tmnxLogExRbkOpBegin indicates the sysUpTime when the exec or rollback revert operation began.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

tmnxLogExRbkOpEnd		1.3.6.1.4.1.6527.3.1.2.12.26.3.1.6
The value of tmnxLogExRbkOpEnd indicates the sysUpTime when the exec or rollback revert operation ended. A value of zero (0) means that the operation has not completed.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

tmnxLogExRbkOpFile		1.3.6.1.4.1.6527.3.1.2.12.26.3.1.7
The value of tmnxLogExRbkOpFile indicates the location and name of the file used for the exec or rollback revert operation.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

tmnxLogExRbkOpUser		1.3.6.1.4.1.6527.3.1.2.12.26.3.1.8
The value of tmnxLogExRbkOpUser indicates the user who initiated the exec or rollback revert operation.
Status: current	Access: read-only
OBJECT-TYPE
	TNamedItem

tmnxLogExRbkOpNumEvents		1.3.6.1.4.1.6527.3.1.2.12.26.3.1.9
The value of tmnxLogExRbkOpNumEvents indicates the number of row entries in the associated tmnxLogExecRollbackEventTable for this exec or rollback revert operation. It is updated only when the exec or rollback revert operation ends. A value of zero (0) means that the operation has not completed.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

tmnxLogExecRollbackEventTable		1.3.6.1.4.1.6527.3.1.2.12.26.4
The Alcatel-Lucent SROS series tmnxLogExecRollbackEventTable provides a history of mib tables modified or specific events generated during an exec or rollback revert operation.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TmnxLogExecRollbackEventEntry

tmnxLogExecRollbackEventEntry		1.3.6.1.4.1.6527.3.1.2.12.26.4.1
Defines a row entry in the tmnxLogExecRollbackEventTable. Each row entry represents either an SNMP table that has been modified or a specific event generated during an exec or rollback revert operation. Entries in this table are created and deleted by the agent.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxLogExecRollbackEventEntry

tmnxLogExRbkEventIndex		1.3.6.1.4.1.6527.3.1.2.12.26.4.1.1
The value of tmnxLogExRbkEventIndex is a unique value that indicates an instance of an event generated during an exec or rollback revert operation.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

tmnxLogExRbkEventOID		1.3.6.1.4.1.6527.3.1.2.12.26.4.1.2
The value of tmnxLogExRbkEventOID indicates the object identifier of either a mib table for which a generic change event was generated or the notification object identifier of a specific event notification generated during the the exec or rollback revert operation. The generic change events are tmnxConfigCreate, tmnxConfigDelete, tmnxConfigModify, and tmnxStateChange notifications. For these event types, the value of tmnxLogExRbkEventOID is the object identifier specified by the tmnxNotifyEntryOID varbind. For specific events generated during an exec or rollback revert, the value of this object is the notification object identifier itself. An object identifier will appear only once in this table.
Status: current	Access: read-only
OBJECT-TYPE
	OBJECT IDENTIFIER

tmnxLogExRbkNotifyObjects		1.3.6.1.4.1.6527.3.1.2.12.26.5
OBJECT IDENTIFIER

tmnxLogExecRollbackOpIndex		1.3.6.1.4.1.6527.3.1.2.12.26.5.1
The value of tmnxLogExecRollbackOpIndex is a unique value that indicates a row entry instance of an exec or rollback revert operation in the tmnxLogExecRollbackOpTable. It is included in the 'exec' and rollback revert start and end notifications.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Unsigned32

tmnxLogColdStartWaitTime		1.3.6.1.4.1.6527.3.1.2.12.27
The value of tmnxLogColdStartWaitTime specifies the time delay that must pass before notifying specific CPM applications that a route is available after a cold reboot.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	0..300

tmnxLogRouteRecoveryWaitTime		1.3.6.1.4.1.6527.3.1.2.12.28
The value of tmnxLogRouteRecoveryWaitTime specifies the time delay that must pass before notifying specific CPM applications after the recovery or change of a route during normal operation.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	0..100

tmnxLogFileDeletedLogId		1.3.6.1.4.1.6527.3.1.2.12.1.1
The value of tmnxLogFileDeletedLogId indicates with which event log-id or accounting-policy-id the deleted file was associated. Note the corresponding entry in the tmnxLogIdTable or tmnxLogApTable may no longer exist.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	TmnxLogIdIndex

tmnxLogFileDeletedFileId		1.3.6.1.4.1.6527.3.1.2.12.1.2
The value of tmnxLogFileDeletedFileId indicates with which event log-id or accounting-policy-id the deleted file was associated. Note that the corresponding entry in the tmnxLogFileIdTable may no longer exist.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	TmnxLogFileId

tmnxLogFileDeletedLogType		1.3.6.1.4.1.6527.3.1.2.12.1.3
The value of tmnxLogFileDeletedLogType indicates whether the deleted file was an 'eventLog' or 'accountingPolicy'.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	TmnxLogFileType

tmnxLogFileDeletedLocation		1.3.6.1.4.1.6527.3.1.2.12.1.4
The value of tmnxLogFileDeletedLocation indicates on which compact flash device the event log or accounting policy file that has been deleted was located.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	TmnxCFlash

tmnxLogFileDeletedName		1.3.6.1.4.1.6527.3.1.2.12.1.5
The value of tmnxLogFileDeletedName indicates the pathname of an event log or accounting policy file that has been deleted because of space contention on a compact flash device.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString

tmnxLogFileDeletedCreateTime		1.3.6.1.4.1.6527.3.1.2.12.1.6
The value of tmnxLogFileDeletedCreateTime indicates the date and time when the deleted file had been created.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DateAndTime

tmnxLogTraceErrorTitle		1.3.6.1.4.1.6527.3.1.2.12.1.7
The value of tmnxLogTraceErrorTitle indicates the title string of the trace error event that generated the tmnxLogTraceError notification.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString	Size(0..50)

tmnxLogTraceErrorSubject		1.3.6.1.4.1.6527.3.1.2.12.1.8
The value of tmnxLogTraceErrorSubject indicates the subject string of the trace error event that generated the tmnxLogTraceError notification. The subject is the entity that originated the event, such as the Slot ID.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString	Size(0..50)

tmnxLogTraceErrorMessage		1.3.6.1.4.1.6527.3.1.2.12.1.9
The value of tmnxLogTraceErrorMessage indicates the message text string of the trace error event that generated the tmnxLogTraceError notification.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString

tmnxLogThrottledEventID		1.3.6.1.4.1.6527.3.1.2.12.1.10
tmnxLogThrottledEventID is used by the tmnxLogEventThrottled notification to indicate the NOTIFICATION-TYPE object identifier of the throttled event.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	OBJECT IDENTIFIER

tmnxLogThrottledEvents		1.3.6.1.4.1.6527.3.1.2.12.1.11
tmnxLogThrottledEvents is used by the tmnxLogEventThrottled notification to indicate the number of events dropped because of event throttling during the last throttle interval.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Unsigned32

tmnxSysLogTargetId		1.3.6.1.4.1.6527.3.1.2.12.1.12
tmnxSysLogTargetId is used by the tmnxSysLogTargetProblem notification to indicate the involved TmnxSyslogId.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	TmnxSyslogId

tmnxSysLogTargetProblemDescr		1.3.6.1.4.1.6527.3.1.2.12.1.13
The value of tmnxSysLogTargetProblemDescr indicates the type of error encountered when trying to deliver events to the destination specified in the TmnxSyslogId.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString

tmnxLogNotifyApInterval		1.3.6.1.4.1.6527.3.1.2.12.1.14
The value of tmnxLogNotifyApInterval indicates how frequently the statistics are collected and written to their destination.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32	5..120

tmnxStdReplayStartEvent		1.3.6.1.4.1.6527.3.1.2.12.1.15
The value of tmnxStdReplayStartEvent indicates the SNMP notification request ID of the first missed event that was replayed when an SNMP notification target address was readded to the RTM following a period when the target address had been removed. It is used by the tmnxStdEventsReplayed notification.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Unsigned32

tmnxStdReplayEndEvent		1.3.6.1.4.1.6527.3.1.2.12.1.16
The value of tmnxStdReplayEndEvent indicates the SNMP notification request ID of the last missed event that was replayed when an SNMP notification target address was readded to the RTM following a period when the target address had been removed. It is used by the tmnxStdEventsReplayed notification.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Unsigned32

tmnxLogSpaceContention		1.3.6.1.4.1.6527.3.1.3.12.0.1
Generated when space contention occurs on the compact flash where a log or billing file creation is being attempted. Space contention exists if: Insufficient space is available on the compact flash to create a file of the same size as the file being rolled over. The first file of this type is being created and less than 10% of the total compact flash space is available. A write operation on a log or billing file is denied due to lack of space.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxLogAdminLocFailed		1.3.6.1.4.1.6527.3.1.3.12.0.2
Generated when an attempt to create a log or billing file at the location specified by tmnxLogFileIdAdminLocation has failed. Indicates that the backup location, if specified, will be used.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxLogBackupLocFailed		1.3.6.1.4.1.6527.3.1.3.12.0.3
Generated when an attempt to create a log or billing file at the location specified by tmnxLogFileIdBackupLoc has failed.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxLogFileRollover		1.3.6.1.4.1.6527.3.1.3.12.0.4
Generated when an event log or accounting policy file's rollover time has expired. The file located as indicated by the value of tmnxLogFileIdOperLocation is closed and a new file is created as specified by tmnxLogFileIdAdminLocation and tmnxLogFileIdBackupLoc.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxLogFileDeleted		1.3.6.1.4.1.6527.3.1.3.12.0.5
Generated when a closed event log or accounting policy file has been deleted as part of the space contention cleanup.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxTestEvent		1.3.6.1.4.1.6527.3.1.3.12.0.6
The tmnxTestEvent notification is generated when the object tmnxEventTest is set to a value of 'doAction'. This event can be used to test that remote log destinations such as syslog and snmp trap destinations are configured correctly.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxLogTraceError		1.3.6.1.4.1.6527.3.1.3.12.0.7
The tmnxLogTraceError notification is generated when a trace error event is detected.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxLogEventThrottled		1.3.6.1.4.1.6527.3.1.3.12.0.8
A tmnxLogEventThrottled notification is generated at the end of the throttling interval when one or more events are dropped because the throttling limit was reached for that interval.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxSysLogTargetProblem		1.3.6.1.4.1.6527.3.1.3.12.0.9
A tmnxSysLogTargetProblem notification is generated when a problem is encountered when trying to deliver data to the syslog destination identfied by the tmnxSysLogTargetId.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxLogAccountingDataLoss		1.3.6.1.4.1.6527.3.1.3.12.0.10
A tmnxLogAccountingDataLoss notification is generated when an accounting file is still being written to when the next interval ends. The collection of statistics for the past interval is immediately stopped and collection is started for the next interval. There are missing records in the file for this past interval.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxStdEventsReplayed		1.3.6.1.4.1.6527.3.1.3.12.0.11
A tmnxStdEventsReplayed notification is generated when an SNMP trap target address is added to the RTM (tmnxVRtrID) following a period when the address had been removed. The value of tmnxStdReplayStartEvent is the SNMP notification request ID of the first event that was replayed. The value of tmnxStdReplayEndEvent is the SNMP notification request ID of the last missed event that was replayed. The value of tmnxStdReplayStart is the request ID of the first event for which there was no route to the trap target address.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxLogEventOverrun		1.3.6.1.4.1.6527.3.1.3.12.0.12
[CAUSE] A tmnxLogEventOverrun notification is generated at the end of the overrun throttling interval when one or more events of the type specified by tmnxLogThrottledEventID were dropped because the logger input stream's input queue limit was exceeded. The overrun throttling interval begins when the input queue limit is first exceeded and ends when the number of events in the input queue has dropped below an internal low watermark. At that point a tmnxLogEventOverrun notification is generated for each event type that had one or more events dropped because of the input queue overrun. The number of dropped events is specified by tmnxLogThrottledEvents. [EFFECT] Logger events have been dropped and were not sent to any log destination. tmnxEventDropCount has been incremented for each event dropped because of input queue overrun. [RECOVERY] The specific event information of dropped events cannot be recovered. The frequency of input queue overruns can be lessened by configuring as few event logs as possible, especially those going to remote destinations such as file, syslog and snmp notification logs.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxLogCompliances		1.3.6.1.4.1.6527.3.1.1.12.1
OBJECT IDENTIFIER

tmnxLogGroups		1.3.6.1.4.1.6527.3.1.1.12.2
OBJECT IDENTIFIER

tmnxLogV4v0Compliance		1.3.6.1.4.1.6527.3.1.1.12.1.4
The compliance statement for revision 4.0 of TIMETRA-LOG-MIB.
Status: obsolete	Access: accessible-for-notify
MODULE-COMPLIANCE

tmnxLogV5v0Compliance		1.3.6.1.4.1.6527.3.1.1.12.1.5
The compliance statement for revision 5.0 of TIMETRA-LOG-MIB.
Status: obsolete	Access: accessible-for-notify
MODULE-COMPLIANCE

tmnxLogV6v0Compliance		1.3.6.1.4.1.6527.3.1.1.12.1.6
The compliance statement for revision 6.0 of TIMETRA-LOG-MIB.
Status: obsolete	Access: accessible-for-notify
MODULE-COMPLIANCE

tmnxLogV6v1Compliance		1.3.6.1.4.1.6527.3.1.1.12.1.7
The compliance statement for revision 6.1 of TIMETRA-LOG-MIB.
Status: current	Access: accessible-for-notify
MODULE-COMPLIANCE

tmnxLogV7v0Compliance		1.3.6.1.4.1.6527.3.1.1.12.1.8
The compliance statement for revision 7.0 of TIMETRA-LOG-MIB.
Status: obsolete	Access: accessible-for-notify
MODULE-COMPLIANCE

tmnxLogV9v0Compliance		1.3.6.1.4.1.6527.3.1.1.12.1.9
The compliance statement for revision 9.0 of TIMETRA-LOG-MIB.
Status: obsolete	Access: accessible-for-notify
MODULE-COMPLIANCE

tmnxLogV8v0Compliance		1.3.6.1.4.1.6527.3.1.1.12.1.10
The compliance statement for revision 7.0 of TIMETRA-LOG-MIB.
Status: obsolete	Access: accessible-for-notify
MODULE-COMPLIANCE

tmnxLogV10v0Compliance		1.3.6.1.4.1.6527.3.1.1.12.1.11
The compliance statement for revision 10.0 of TIMETRA-LOG-MIB.
Status: current	Access: accessible-for-notify
MODULE-COMPLIANCE

tmnxLogGlobalGroup		1.3.6.1.4.1.6527.3.1.1.12.2.1
The group of objects supporting management of event logging capabilities on Alcatel-Lucent SROS series systems.
Status: current	Access: accessible-for-notify
OBJECT-GROUP

tmnxLogAccountingPolicyGroup		1.3.6.1.4.1.6527.3.1.1.12.2.3
The group of objects supporting management of accounting policies capabilities on Alcatel-Lucent SROS series systems.
Status: current	Access: accessible-for-notify
OBJECT-GROUP

tmnxLogFileIdGroup		1.3.6.1.4.1.6527.3.1.1.12.2.4
The group of objects supporting management of Log File destinations on Alcatel-Lucent SROS series systems.
Status: current	Access: accessible-for-notify
OBJECT-GROUP

tmnxLogSyslogGroup		1.3.6.1.4.1.6527.3.1.1.12.2.5
The group of objects supporting management of Log Syslog destinations on Alcatel-Lucent SROS series systems.
Status: obsolete	Access: accessible-for-notify
OBJECT-GROUP

tmnxSnmpTrapGroup		1.3.6.1.4.1.6527.3.1.1.12.2.6
The group of objects supporting management of Log SNMP notification destinations on Alcatel-Lucent SROS series systems.
Status: obsolete	Access: accessible-for-notify
OBJECT-GROUP

tmnxLogEventsR2r1Group		1.3.6.1.4.1.6527.3.1.1.12.2.10
The group of objects supporting management of Log Events on Alcatel-Lucent SROS series systems release 2.1.
Status: obsolete	Access: accessible-for-notify
OBJECT-GROUP

tmnxLogNotifyObjsR3r0Group		1.3.6.1.4.1.6527.3.1.1.12.2.13
The group of objects supporting management of Log notifications on Alcatel-Lucent SROS series systems.
Status: obsolete	Access: accessible-for-notify
OBJECT-GROUP

tmnxLogNotificationR3r0Group		1.3.6.1.4.1.6527.3.1.1.12.2.14
The group of notifications supporting the Log feature on Alcatel-Lucent SROS series systems release 3.0.
Status: obsolete	Access: accessible-for-notify
NOTIFICATION-GROUP

tmnxLogV4v0Group		1.3.6.1.4.1.6527.3.1.1.12.2.15
The group of objects supporting management of event logs on Alcatel-Lucent SROS series systems.
Status: obsolete	Access: accessible-for-notify
OBJECT-GROUP

tmnxSnmpSetErrsGroup		1.3.6.1.4.1.6527.3.1.1.12.2.16
The group of objects supporting management of SNMP SET failure error messages.
Status: current	Access: accessible-for-notify
OBJECT-GROUP

tmnxLogEventsV5v0Group		1.3.6.1.4.1.6527.3.1.1.12.2.17
The group of objects supporting management of Log Events on Alcatel-Lucent SROS series systems release 5.0.
Status: current	Access: accessible-for-notify
OBJECT-GROUP

tmnxLogNotifyObjsV5v0Group		1.3.6.1.4.1.6527.3.1.1.12.2.18
The group of objects supporting management of Log notifications on Alcatel-Lucentx SROS series systems release 5.0.
Status: obsolete	Access: accessible-for-notify
OBJECT-GROUP

tmnxLogNotificationV5v0Group		1.3.6.1.4.1.6527.3.1.1.12.2.19
The group of notifications supporting the Log feature on Alcatel-Lucent SROS series systems release 5.0.
Status: obsolete	Access: accessible-for-notify
NOTIFICATION-GROUP

tmnxLogSyslogV5v0Group		1.3.6.1.4.1.6527.3.1.1.12.2.20
The group of objects supporting management of Log Syslog destinations on Alcatel-Lucent SROS series systems release 5.0.
Status: current	Access: accessible-for-notify
OBJECT-GROUP

tmnxSnmpTrapV5v0Group		1.3.6.1.4.1.6527.3.1.1.12.2.21
The group of objects supporting management of Log SNMP notification destinations on Alcatel-Lucent SROS series systems for release 5.0.
Status: current	Access: accessible-for-notify
OBJECT-GROUP

tmnxLogV5v0Group		1.3.6.1.4.1.6527.3.1.1.12.2.22
The group of objects supporting management of event logs on Alcatel-Lucent SROS series systems in release 5.0.
Status: current	Access: accessible-for-notify
OBJECT-GROUP

tmnxLogObsoleteObjsV5v0Group		1.3.6.1.4.1.6527.3.1.1.12.2.23
The group of objects supporting management of TiMOS logs obsoleted on Alcatel-Lucent SROS series systems in release 5.0.
Status: current	Access: accessible-for-notify
OBJECT-GROUP

tmnxLogNotifyObjsV6v0Group		1.3.6.1.4.1.6527.3.1.1.12.2.24
The group of objects supporting management of Log notifications on Alcatel-Lucent SROS series systems release 6.0.
Status: obsolete	Access: accessible-for-notify
OBJECT-GROUP

tmnxLogNotificationV6v0Group		1.3.6.1.4.1.6527.3.1.1.12.2.25
The group of notifications supporting the Log feature on Alcatel-Lucent SROS series systems release 6.0.
Status: current	Access: accessible-for-notify
NOTIFICATION-GROUP

tmnxSnmpTrapDestV6v0Group		1.3.6.1.4.1.6527.3.1.1.12.2.26
The group of objects added to support SNMP trap destinations in the Alcatel-Lucent SROS series systems release 6.0.
Status: current	Access: accessible-for-notify
OBJECT-GROUP

tmnxLogAccountingPolicyV6v1Group		1.3.6.1.4.1.6527.3.1.1.12.2.27
The group of objects supporting management of accounting policies capabilities on Alcatel-Lucent SROS series systems release 6.1.
Status: current	Access: accessible-for-notify
OBJECT-GROUP

tmnxLogAccountingPolicyCRV7v0Group		1.3.6.1.4.1.6527.3.1.1.12.2.28
The group of objects supporting the creation of a custom record inside a accounting policy on Alcatel-Lucent SROS series systems.
Status: current	Access: accessible-for-notify
OBJECT-GROUP

tmnxLogRoutePreferenceV7v0Group		1.3.6.1.4.1.6527.3.1.1.12.2.29
The group of objects supporting routing preferences of Log Events on Alcatel-Lucent SROS series systems release 7.0.
Status: current	Access: accessible-for-notify
OBJECT-GROUP

tmnxLogNotifyObjsV8v0Group		1.3.6.1.4.1.6527.3.1.1.12.2.30
The group of objects supporting management of Log notifications on Alcatel-Lucent SROS series systems release 8.0.
Status: current	Access: accessible-for-notify
OBJECT-GROUP

tmnxLogNotificationV9v0Group		1.3.6.1.4.1.6527.3.1.1.12.2.31
The group of notifications supporting the Log feature on Alcatel SROS series systems added in release 9.0.
Status: current	Access: accessible-for-notify
NOTIFICATION-GROUP

tmnxLogEventDampedV8v0Group		1.3.6.1.4.1.6527.3.1.1.12.2.32
The group of objects supporting damping of change events on Alcatel-Lucent SROS series systems added in release 8.0r7.
Status: current	Access: accessible-for-notify
OBJECT-GROUP

tmnxLogApV9v0Group		1.3.6.1.4.1.6527.3.1.1.12.2.33
The group of objects extending the application log table on Alcatel-Lucent SROS series systems added in release 9.0.
Status: current	Access: accessible-for-notify
OBJECT-GROUP

tmnxLogExRbkOpGroup		1.3.6.1.4.1.6527.3.1.1.12.2.34
The group of objects managing exec and rollback revert event history.
Status: current	Access: accessible-for-notify
OBJECT-GROUP

tmnxLogNotifyObjsV10v0Group		1.3.6.1.4.1.6527.3.1.1.12.2.35
The group of accessible-for-notify objects added to Alcatel-Lucent SROS series systems release 10.0.
Status: current	Access: accessible-for-notify
OBJECT-GROUP

tmnxLogApExtGroup		1.3.6.1.4.1.6527.3.1.1.12.2.36
The group of objects extending the accounting policy table on Alcatel-Lucent SROS series systems.
Status: current	Access: accessible-for-notify
OBJECT-GROUP

tmnxLogAppRouteNotifV10v0Group		1.3.6.1.4.1.6527.3.1.1.12.2.37
The group of objects supporting notifications on completion of wait time after cold reboot and route recovery on Alcatel-Lucent SROS series systems release 10.0.
Status: current	Access: accessible-for-notify
OBJECT-GROUP