TIMETRA-TC-MIB

File: TIMETRA-TC-MIB.mib (265266 bytes)

Imported modules

INET-ADDRESS-MIB SNMPv2-SMI SNMPv2-TC
TIMETRA-GLOBAL-MIB

Imported symbols

InetAddress InetAddressIPv6 InetAddressPrefixLength
InetAddressType Integer32 IpAddress
MODULE-IDENTITY Unsigned32 DisplayString
TEXTUAL-CONVENTION TruthValue timetraModules

Defined Types

InterfaceIndex  
A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub- layer must remain constant at least from one re- initialization of the entity's network management system to the next re-initialization.
TEXTUAL-CONVENTION    
  Integer32  

TmnxPortID  
A portid is a unique 32 bit number with special encoding. Refer to TIMETRA-CHASSIS-MIB::tmnxChassisPortIdScheme for a description of the various port mapping schemes used by the system for physical ports and channels. Virtual ports and LAGs are encoded as: 32 29 | 28 10 | 9 1 | +---------+-------------------+-------+ | 0 1 0 0 | zeros | ID | Virtual Port +---------+-------------------+-------+ 32 29 | 28 11 | 10 1 | +---------+-------------------+-------+ | 0 1 0 1 | zeros | ID | LAG Port +---------+-------------------+-------+ A card port number (cpn) has significance within the context of the card on which it resides(i.e., cpn 2 may exist in one or more cards in the chassis). Whereas, portid is an unique/absolute port number (apn) within a given chassis. An 'invalid portid' is a TmnxPortID with a value of 0x1e000000 as represented below. 32 30 | 29 26 | 25 22 | 21 16 | 15 1 | +-----+-------+-------+-------+-------+ |zero | ones | zero | zero | zero | Invalid Port +-----+-------+-------+-------+-------+
TEXTUAL-CONVENTION    
  Unsigned32  

TmnxEncapVal  
The value of the label used to identify the entity using the specified encapsulation value on a specific port. The format of this object depends on the encapsulation type defined on this port. When the encapsulation is nullEncap the value of this object must be zero. 31 0 +--------+--------+--------+--------+ |00000000 00000000 00000000 00000000| +--------+--------+--------+--------+ When the encapsulation is dot1qEncap the value of this object is equal to the 12-bit IEEE 802.1Q VLAN ID. 31 0 +--------+--------+--------+--------+ |00000000 00000000 0000XXXX XXXXXXXX| +--------+--------+--------+--------+ Bit 31 is set to 0 in the case of tagged-VLAN. Bit 31 is set to 1 in the case of dotq-CP as follows: 31 0 +--------+--------+--------+--------+ |10000000 00000000 0000XXXX XXXXXXXX| +--------+--------+--------+--------+ When the encapsulation is mplsEncap the value of this object is equal to the 20-bit LSP ID. 31 0 +--------+--------+--------+--------+ |00000000 0000XXXX XXXXXXXX XXXXXXXX| +--------+--------+--------+--------+ When the encapsulation is frEncap, the value of this object is equal to the 10-bit Frame Relay DLCI. 31 0 +--------+--------+--------+--------+ |00000000 00000000 000000XX XXXXXXXX| +--------+--------+--------+--------+ When the encapsulation is qinqEncap, the value of the outer 802.1Q VLAN ID is encoded in the least significant 16 bits, and the value of the inner VLAN ID is encoded in the most significant 16 bits. 31 0 +--------+--------+--------+--------+ |0000YYYY YYYYYYYY 0000XXXX XXXXXXXX| +--------+--------+--------+--------+ where: - '*' is represented as 4095. - '0' is represented as 0. - any other value in between as a valid tag. - '*.null' is represented in the following way: 31 0 +--------+--------+--------+--------+ |10000000 00000000 00001111 11111111| +--------+--------+--------+--------+ Bit 30 is set to 0 in the case of tagged-qinq for the bottom tag. Bit 30 is set to 1 in the case of qinq-CP with bottom tag. Bit 15 is set to 0 in the case of tagged-qinq for the top tag. Bit 15 is set to 1 in the case of qinq-CP with top tag as follows: 31 0 +--------+--------+--------+--------+ |0100YYYY YYYYYYYY 0100XXXX XXXXXXXX| +--------+--------+--------+--------+ When the encapsulation is atmEncap, the value of the ATM VCI is encoded in the least significant 16 bits, and the value of the ATM VPI is encoded in the next 12 bits. For ATM VCs, the top 3 bits are 000. The value of the ATM VCI is encoded in the least significant 16 bits, and the value of the ATM VPI is encoded in the next 12 bits. 31 0 +--------+--------+--------+--------+ |0000YYYY YYYYYYYY XXXXXXXX XXXXXXXX| +--------+--------+--------+--------+ For ATM capture VCs, bits 0 and 28 are 1. 31 0 +--------+--------+--------+--------+ |00010000 00000000 00000000 00000001| +--------+--------+--------+--------+ For ATM VPs, the top 3 bits are 010. The value of the ATM VPI is encoded in the least significant 12 bits. 31 0 +--------+--------+--------+--------+ |01000000 00000000 0000XXXX XXXXXXXX| +--------+--------+--------+--------+ For ATM VP ranges, the top 3 bits are 100. The value of the start of the ATM VPI range is encoded in the least significant 12 bits, and the value of the end of the ATM VP range is encoded in the next 12 bits. 31 0 +--------+--------+--------+--------+ |10000000 YYYYYYYY YYYYXXXX XXXXXXXX| +--------+--------+--------+--------+ For ATM ports, the top 3 bits are 110, and the rest of the bits must be zero. 31 0 +--------+--------+--------+--------+ |11000000 00000000 00000000 00000000| +--------+--------+--------+--------+ For ATM CPs, the top 3 bits are 001. The value of the ATM CP is encoded in the least significant 13 bits. 31 0 +--------+--------+--------+--------+ |00100000 00000000 000XXXXX XXXXXXXX| +--------+--------+--------+--------+ When the encapsulation is wanMirrorEncap the value of this object is equal to the 12-bit value. 31 0 +--------+--------+--------+--------+ |00000000 00000000 0000XXXX XXXXXXXX| +--------+--------+--------+--------+ Some ports have a restrictions to the encapsulation types that they can support and hence impose restrictions on the respective formats defined above.
TEXTUAL-CONVENTION    
  Unsigned32  

QTag  
The QTag data type is a 12-bit integer tag used to identify a service. The values 0 and 4095 are not allowed.
TEXTUAL-CONVENTION    
  Integer32 1..4094  

QTagOrZero  
The data type QTagOrZero represents a VLAN tag. The value '0' indicates that no VLAN tag is provisioned, or that its value is unknown.
TEXTUAL-CONVENTION    
  Unsigned32 0..4094  

QTagFullRange  
The data type QTagFullRange represents a VLAN tag. A VLAN tag is 12 bits is size. The data type QTagFullRange covers the whole range of possible values. (0..4095 or 0x0 .. 0xFFF)
TEXTUAL-CONVENTION    
  Unsigned32 0..4095  

QTagFullRangeOrNone  
The data type QTagFullRangeOrNone represents a VLAN tag. A VLAN tag is 12 bits is size. The data type QTagFullRange covers the whole range of possible values. (0..4095 or 0x0 .. 0xFFF). The value '-1' indicates the absence of a VLAN tag.
TEXTUAL-CONVENTION    
  Integer32 -1 | 0..4095  

TmnxSapAASubScope  
The TmnxSapAASubScope data type is an enumerated integer that specifies the scope of the AA subscriber. Values: none (0) - The AA subscriber has no scope. subscriber (1) - The AA subscriber has esm subscriber scope. mac (2) - The AA subscriber has esm MAC host scope.
TEXTUAL-CONVENTION    
  INTEGER none(0), subscriber(1), mac(2)  

TmnxStrSapId  
The value of TmnxStrSapId is a printable string which contains the owner SAP Id or equivalent on a remote system. The string should contain the printable string equivalent of the textual conventions TmnxPortID and TmnxEncapVal in the format specified as TmnxPortID[:TmnxEncapVal]
TEXTUAL-CONVENTION    
  DisplayString Size(0..32)  

IpAddressPrefixLength  
the number of bits to match in an IP address mask.
TEXTUAL-CONVENTION    
  Integer32 0..32  

TmnxActionType  
The TmnxActionType data type is an enumerated integer that describes the values used to support action or operation style commands. Setting a variable of this type to 'doAction' causes the action to occur. GETs and GETNEXTs on this variable return 'not-applicable'.
TEXTUAL-CONVENTION    
  INTEGER doAction(1), notApplicable(2)  

TmnxAdminState  
The TmnxAdminState data type is an enumerated integer that describes the values used to identify the administratively desired state of functional modules.
TEXTUAL-CONVENTION    
  INTEGER noop(1), inService(2), outOfService(3)  

TmnxOperState  
The TmnxOperState data type is an enumerated integer that describes the values used to identify the current operational state of functional modules.
TEXTUAL-CONVENTION    
  INTEGER unknown(1), inService(2), outOfService(3), transition(4)  

TmnxStatus  
The TmnxStatus data type is an enumerated integer that describes the values used to identify the current status of functional modules in the system such as OSPF and MPLS protocols. Setting this variable to 'create' causes instantiation of the feature in the system. Setting it to 'delete' removes the instance and all associated configuration information.
TEXTUAL-CONVENTION    
  INTEGER create(1), delete(2)  

TmnxEnabledDisabledAdminState  
The TmnxEnabledDisabledAdminState data type is an enumerated integer that describes the values used to identify whether an entity is 'enabled' or 'disabled'. It is to be used for admin state leafs.
TEXTUAL-CONVENTION    
  INTEGER enabled(1), disabled(2)  

TmnxEnabledDisabled  
The TmnxEnabledDisabled data type is an enumerated integer that describes the values used to identify whether an entity is 'enabled' or 'disabled'.
TEXTUAL-CONVENTION    
  INTEGER enabled(1), disabled(2)  

TmnxEnabledDisabledOrNA  
An object of type TmnxEnabledDisabledOrNA indicates if an entity is enabled or disabled, or if enabled/disabled is not applicable to the entity.
TEXTUAL-CONVENTION    
  INTEGER enabled(1), disabled(2), notApplicable(3)  

TmnxEnabledDisabledOrInherit  
The TmnxEnabledDisabledOrInherit data type is an enumerated integer that describes the values used to identify whether an entity is 'enabled', 'disabled' or inherits its state from another object that is usually in another mib table.
TEXTUAL-CONVENTION    
  INTEGER enabled(1), disabled(2), inherit(3)  

TmnxTimeInterval  
The TmnxTimeInterval data type is used anywhere the SNMPv2-TC TimeInterval TEXTUAL-CONVENTION can be used when an object requires longer intervals than 248 days. A period of time, measured in units of 0.01 seconds.
TEXTUAL-CONVENTION    
  Unsigned32  

TNamedItem  
The name of an item. When used as an index to a table, the item name uniquely identifies the instance. When used in a reference (TNamedItemOrEmpty) the item name entry must exist in the table. Note, use only NVT ASCII displayable characters here, no control characters, no UTF-8, etc.
TEXTUAL-CONVENTION    
  DisplayString Size(1..32)  

TNamedItemOrEmpty  
The name of an item, or an empty string. When used in a reference (TNamedItemOrEmpty) the item name entry must exist in the table. Note, use only NVT ASCII displayable characters here, no control characters, no UTF-8, etc.
TEXTUAL-CONVENTION    
  DisplayString Size(0|1..32)  

TLNamedItem  
The long name of an item. When used as an index to a table, the item name uniquely identifies the instance. When used in a reference (TLNamedItemOrEmpty) the item name entry must exist in the table. Note, use only NVT ASCII displayable characters here, no control characters, no UTF-8, etc.
TEXTUAL-CONVENTION    
  DisplayString Size(1..64)  

TLNamedItemOrEmpty  
The long name of an item, or an empty string. When used in a reference (TLNamedItemOrEmpty) the item name entry must exist in the table. Note, use only NVT ASCII displayable characters here, no control characters, no UTF-8, etc.
TEXTUAL-CONVENTION    
  DisplayString Size(0|1..64)  

TXLNamedItem  
The extra long name of an item. When used as an index to a table, the item name uniquely identifies the instance. When used in a reference (TXLNamedItemOrEmpty) the item name entry must exist in the table. Note, use only NVT ASCII displayable characters here, no control characters, no UTF-8, etc.
TEXTUAL-CONVENTION    
  DisplayString Size(1..255)  

TXLNamedItemOrEmpty  
The extra long name of an item, or an empty string. When used in a reference (TXLNamedItemOrEmpty) the item name entry must exist in the table. Note, use only NVT ASCII displayable characters here, no control characters, no UTF-8, etc.
TEXTUAL-CONVENTION    
  DisplayString Size(0|1..255)  

TItemDescription  
Description for an item. Note, use only NVT ASCII displayable characters here, no control characters, no UTF-8, etc.
TEXTUAL-CONVENTION    
  DisplayString Size(0..80)  

TItemLongDescription  
Longer description for an item. Note, use only NVT ASCII displayable characters here, no control characters, no UTF-8, etc.
TEXTUAL-CONVENTION    
  DisplayString Size(0..160)  

TRegularExpression  
A regular expression string.
TEXTUAL-CONVENTION    
  DisplayString  

TmnxHttpRedirectUrl  
A string that represents an HTTP URL configured for HTTP redirection. The string may contain a macro '' that specifies substitution of '' by another string; the origin of that string is documented where this textual convention is used. The string may contain a macro '' that specifies substitution of '' by another string, representing a MAC address; the origin of that string is documented where this textual convention is used. The string may contain a macro '' that specifies substitution of '' by another string, representing an IP address; the origin of that string is documented where this textual convention is used. The string may contain a macro '' that specifies substitution of '' by another string, representing an subscriber ID; the origin of that string is documented where this textual convention is used. The string may contain a macro '' that specifies substitution of '' by another string, representing a SAP (Service Access Point); the origin of that string is documented where this textual convention is used. The string may contain a macro '' that specifies substitution of '' by another string; the origin of that string is documented where this textual convention is used. The string may contain a macro '' that specifies substitution of '' by a bytestring, representing a circuit-id or interface-id; the origin of that string is documented where this textual convention is used. The string may contain a macro '' that specifies substitution of '' by a bytestring, representing a remote-id; the origin of that string is documented where this textual convention is used. Not all substitution macro's are supported in every situation; an unsupported macro is ignored (substituted with nothing); the set of supported macro's should be documented where this textual convention is used.
TEXTUAL-CONVENTION    
  DisplayString  

TmnxDisplayStringURL  
A string that represents an URL. If the URL contains login information in the form of 'username:password' this login information will be blanked out in the SNMP get response, by replacing the login information with '*:*'.
TEXTUAL-CONVENTION    
  DisplayString Size(0..180)  

TmnxVRtrID  
A number used to identify a virtual router instance in the system.
TEXTUAL-CONVENTION    
  Integer32 1..10240  

TmnxVRtrIDOrZero  
A number used to identify a virtual router instance in the system. The number 0 will have special significance in the context the TC is used.
TEXTUAL-CONVENTION    
  Integer32 0..10240  

VRtrIgmpHostMcRDstStatType  
The VRtrIgmpHostMcRDstStatType data type is an enumerated integer that indicates a type of IGMP host mcast reporting destination statistics.
TEXTUAL-CONVENTION    
  INTEGER joinTx(1), joinDenyTx(2), dropTx(3), joinLost(4), joinDenyLost(5), dropLost(6)  

TmnxBgpAutonomousSystem  
an autonomous system (AS) number.
TEXTUAL-CONVENTION    
  Integer32 0..65535  

TmnxBgpLocalPreference  
a local route preference value.
TEXTUAL-CONVENTION    
  Unsigned32  

TmnxBgpPreference  
a route preference value.
TEXTUAL-CONVENTION    
  Unsigned32 0..255  

TmnxCustId  
A number used to identify a Customer or Subscriber. This ID must be unique within the Service Domain. The value 0 is used as the null ID.
TEXTUAL-CONVENTION    
  Unsigned32 0 | 1..2147483647  

TmnxCustIdNoZero  
A number used to identify a Customer or Subscriber. This ID must be unique within the Service Domain.
TEXTUAL-CONVENTION    
  Unsigned32 1..2147483647  

BgpPeeringStatus  
The status of the BGP peering session.
TEXTUAL-CONVENTION    
  INTEGER notApplicable(0), installed(1), notInstalled(2), noEnhancedSubmgt(3), wrongAntiSpoof(4), parentItfDown(5), hostInactive(6), noDualHomingSupport(7), invalidRadiusAttr(8), noDynamicPeerGroup(9), duplicatePeer(10), maxPeersReached(11), l2AwNotSupported(12), gtpNotSupported(13), genError(14)  

TmnxRipListenerStatus  
The status of the RIP Listener session.
TEXTUAL-CONVENTION    
  INTEGER notApplicable(0), active(1), inactive(2), noEnhancedSubmgt(3), wrongAntiSpoof(4), parentItfDown(5), hostInactive(6), l2AwNotSupported(7), gtpNotSupported(8), mcStandby(9), ripDisabled(10)  

TmnxServId  
A number used to identify a Service. This ID must be unique within the Service Domain. The value 0 is used as the null ID.
TEXTUAL-CONVENTION    
  Unsigned32 0 | 1..2147483647 | 2147483648 | 2147483649 | 2147483650 | 2147483651..2147483690 | 2147483691..2148007980 | 2148007981..2148012076 | 2148012077..2148016172 | 2148016173..2148278316 | 2148278317 | 2148278318..2148278381  

TmnxExtServId  
A number used to identify an external Service. This ID must be unique within the Service Domain. The value 0 is used as the null ID.
TEXTUAL-CONVENTION    
  Unsigned32 0 | 1..2147483647  

TmnxAdminStateUpDown  
TmnxAdminStateUpDown data type is an enumerated integer that describes the values used to identify the administrative state of a snmp row.
TEXTUAL-CONVENTION    
  INTEGER up(1), down(2)  

TmnxAdminStateTruthValue  
TmnxAdminStateTruthValue data type is an TruthValue object used to identify the administrative state of a snmp row. A value of 'true' means the snmp row is administrative 'up'.
TEXTUAL-CONVENTION    
  TruthValue  

TruthValueNoTypeTranslator  
Represents a boolean value.
TEXTUAL-CONVENTION    
  INTEGER true(1), false(2)  

ServiceAdminStatus  
ServiceAdminStatus data type is an enumerated integer that describes the values used to identify the administrative state of a service.
TEXTUAL-CONVENTION    
  INTEGER up(1), down(2)  

ServiceOperStatus  
ServiceOperStatus data type is an enumerated integer that describes the values used to identify the current operational state of a service.
TEXTUAL-CONVENTION    
  INTEGER up(1), down(2)  

TPolicyID  
The identification number of a policy.
TEXTUAL-CONVENTION    
  Unsigned32 0..65535 | 65536 | 65537 | 65538  

TTmplPolicyID  
The identification number of a policy for template objects.
TEXTUAL-CONVENTION    
  Unsigned32 1..65535  

TQosIngressPolicyID  
The identification number of a QoS ingress policy.
TEXTUAL-CONVENTION    
  TPolicyID  

TSapIngressPolicyID  
The identification number of a SAP ingress policy.
TEXTUAL-CONVENTION    
  TPolicyID  

TSapEgressPolicyID  
The identification number of a SAP egress policy.
TEXTUAL-CONVENTION    
  TPolicyID 1..65535 | 65536 | 65537 | 65538  

TAnyQosPolicyID  
The identification number of QoS policy. Any value greater than 65535 indicates the policy was created by the system. The format is: +--------------------------------+ |<----C-----><-B><------A------->| +--------------------------------+ 31 0 where: A (16 bits) is the base policy identifier. B (4 bits) is the 'policy type'. C (12 bits) is the auxiliary identifier. When policy type = 0 (0000b), the acceptable range for base policy identifier is 1..65535. This is the user configured values. When policy type = 1 (0001b) [NAT/LNS], the acceptable range for base policy identifier is 0..2. These policies are considered 'internal' and cannot be created or modified by the user. When policy type = 2 (0010b) The auxiliary identifier represents internal policies that are created by the system based on dynamic flow based requests from diameter and cannot be modified by the user. These polices ranges from 1..2047. For all other policy types, the auxiliary identifier must be zero.
TEXTUAL-CONVENTION    
  Unsigned32 1..4294967295  

TAnyQosPolicyIDorZero  
The identification number of QoS policy. Refer to the description of the textual convention TAnyQosPolicyID for more info on how this number is to be interpreted.
TEXTUAL-CONVENTION    
  Unsigned32 0 | 1..4294967295  

TSdpIngressPolicyID  
The identification number of a SDP ingress network policy.
TEXTUAL-CONVENTION    
  TPolicyID  

TSdpEgressPolicyID  
The identification number of a SDP egress network policy.
TEXTUAL-CONVENTION    
  TPolicyID  

TQosQGrpInstanceIDorZero  
The identification number of a QoS queue group instance. The value of '0' indicates the system determined default value.
TEXTUAL-CONVENTION    
  Unsigned32 0 | 1..65535  

TmnxCreateOrigin  
The TmnxCreateOrigin indicates the entity that created the entry.
TEXTUAL-CONVENTION    
  INTEGER manual(1), bgp-l2vpn(2), radius(3), bgpSignalL2vpn(4), multiSegmentPW(5), vplsPmsi(6), dynScript(7), bof(8), bgpSignalVpws(9), vsd(12), evpn(13), vsd-sd(14), satellites(15), fpe(16), evpnIsa(17), greBridged(18), tli(19), pdn(20)  

TmnxBsxTransitIpPolicyId  
TmnxBsxTransitIpPolicyId identifies a transit IP policy.
TEXTUAL-CONVENTION    
  Unsigned32 1..65535  

TmnxBsxTransitIpPolicyIdOrZero  
TmnxBsxTransitIpPolicyId identifies a transit ip policy. The value '0' indicates an invalid transit IP policy.
TEXTUAL-CONVENTION    
  Unsigned32 0 | 1..65535  

TmnxBsxTransPrefPolicyId  
TmnxBsxTransPrefPolicyId identifies a transit prefix policy.
TEXTUAL-CONVENTION    
  Unsigned32 1..65535  

TmnxBsxTransPrefPolicyIdOrZero  
TmnxBsxTransPrefPolicyId identifies a transit prefix policy. The value '0' indicates an invalid transit prefix policy.
TEXTUAL-CONVENTION    
  Unsigned32 0 | 1..65535  

TmnxBsxAarpId  
TmnxBsxAarpId identifies an instance of the AA Redundancy Protocol (AARP).
TEXTUAL-CONVENTION    
  Unsigned32 1..65535  

TmnxBsxAarpIdOrZero  
TmnxBsxAarpIdOrZero identifies an instance of the AA Redundancy Protocol (AARP). The value of '0' indicates an invalid AARP instance.
TEXTUAL-CONVENTION    
  Unsigned32 0 | 1..65535  

TmnxBsxAarpServiceRefType  
TmnxBsxAarpServiceRefType identifies the role of the SAP or Spoke SDP service point being referenced by an AARP instance. This reference is made in the context of a AARP instance identified by TmnxBsxAarpIdOrZero. The service reference types are: none(0) - service reference type is not applicable. dualHomed(1) - the service reference point is a SAP or Spoke SDP connected into a dually homed network being protected by the AARP instance. shuntSubscriberSide(2) - the service reference point is a Spoke SDP acting as a subscriber side shunt used by the AARP instance. A subscriber side shunt carries the local from/to subscriber traffic when AA is performed remotely. shuntNetworkSide(3) - the service reference point is a Spoke SDP acting as a network side shunt used by the AARP instance. A network side shunt carries the local from/to network traffic when AA is performed remotely. dualHomedSecondary(4) - the secondary service reference point is a SAP or Spoke SDP connected into a dually homed network being protected by the AARP instance. It functions as a backup to the 'dualHomed(1)' primary reference point. For the case when TmnxBsxAarpIdOrZero refers to the invalid AARP instance '0', the service reference type is 'none(0)'.
TEXTUAL-CONVENTION    
  INTEGER none(0), dualHomed(1), shuntSubscriberSide(2), shuntNetworkSide(3), dualHomedSecondary(4)  

TmnxBsxIsaAaGroupIndexOrZero  
TmnxBsxIsaAaGroupIndexOrZero is an index of a group of BSX MDAs. The value of zero indicates that no BSX MDA group is specified.
TEXTUAL-CONVENTION    
  Unsigned32 0..255  

TmnxBsxAaGrpPartIndexOrZero  
TmnxBsxAaGrpPartIndexOrZero is an index of an Application Assurance partition within an Application Assurance group, and is a unique 32-bit number encoded as follows. | 32 25 | 24 9 | 8 1 | +---------+---------+----------+ | 0 | partidx | groupidx| Partition Index +---------+---------+----------+ - groupidx represents a group of ISA MDAs and has a valid range from 1..255. The corresponding TmnxBsxIsaAaGroupIndex must already exist in the tmnxBsxIsaAaGrpTable. - partidx represents a partition within a group and has a valid range from 0..65535. A partition index of '0' represents group wide information. The value of zero indicates that no Application Assurance partition is specified
TEXTUAL-CONVENTION    
  Unsigned32 0..16777215  

TSapEgrEncapGrpQosPolicyIdOrZero  
TSapEgrEncapGrpQosPolicyIdOrZero identifies SAP egress Encapsulation group QoS policy. The value '0' indicates no QoS policy is set.
TEXTUAL-CONVENTION    
  Unsigned32 0 | 1..65535  

TSapEgrEncapGroupType  
TSapEgrEncapGroupType identifies Encapsulation group type on SAP egress.
TEXTUAL-CONVENTION    
  INTEGER isid(1)  

TSapEgrEncapGroupActionType  
TSapEgrEncapGroupActionType identifies Encapsulation group action type on SAP egress. It is used to create or destroy row entries in an associated table.
TEXTUAL-CONVENTION    
  INTEGER create(1), destroy(2)  

TPerPacketOffset  
The value, in bytes, of the adjustment to make to the size of each packet for accounting.
TEXTUAL-CONVENTION    
  Integer32 -32..31  

TPerPacketOffsetOvr  
The value, in bytes, of the override of the adjustment to make to the size of each packet for accounting. A value of -128 indicates no override.
TEXTUAL-CONVENTION    
  Integer32 -128 | -32..31  

TIngressHsmdaPerPacketOffset  
The value, in bytes, of the adjustment to make to the size of each incoming packet for accounting.
TEXTUAL-CONVENTION    
  Integer32 -32..31  

TIngHsmdaPerPacketOffsetOvr  
The value, in bytes, of the override of the adjustment to make to the size of each incoming packet for accounting. A value of -128 indicates no override.
TEXTUAL-CONVENTION    
  Integer32 -128 | -32..31  

TEgressQPerPacketOffset  
The value, in bytes, of the adjustment to make to the size of each packet for accounting.
TEXTUAL-CONVENTION    
  Integer32 -64..32  

TEgressPerPacketOffset  
The value, in bytes, of the adjustment to make to the size of each packet for accounting.
TEXTUAL-CONVENTION    
  Integer32 -64..31  

TEgressPerPacketOffsetOvr  
The value, in bytes, of the override for the adjustment to make to the size of each packet for accounting. A value of -128 indicates no override.
TEXTUAL-CONVENTION    
  Integer32 -128 | -64..31  

TEgressHsmdaPerPacketOffset  
The value, in bytes, of the adjustment to make to the size of each outgoing packet for accounting.
TEXTUAL-CONVENTION    
  Integer32 -64..31  

TEgrHsmdaPerPacketOffsetOvr  
The value, in bytes, of the override of the adjustment to make to the size of each outgoing packet for accounting. A value of -128 indicates no override.
TEXTUAL-CONVENTION    
  Integer32 -128 | -64..31  

TIngressQPerPacketOffset  
The value, in bytes, of the adjustment to make to the size of each incoming packet for accounting. Only even values are supported.
TEXTUAL-CONVENTION    
  Integer32 -32..30  

THsmdaCounterIdOrZero  
The identification number of a HSMDA counter. The value 0 indicates an undefined counter id.
TEXTUAL-CONVENTION    
  Unsigned32 0 | 1..8  

THsmdaCounterIdOrZeroOrAll  
The identification number of a HSMDA counter. The value (0) indicates an undefined counter id. The value (-1) is used to indicate all counters.
TEXTUAL-CONVENTION    
  Integer32 -1 | 0 | 1..8  

TIngressHsmdaCounterId  
The identification number of a HSMDA ingress counter.
TEXTUAL-CONVENTION    
  Unsigned32 1..8  

TIngressHsmdaCounterIdOrZero  
The identification number of a HSMDA ingress counter. The value 0 indicates an undefined counter id.
TEXTUAL-CONVENTION    
  Unsigned32 0 | 1..8  

TEgressHsmdaCounterId  
The identification number of a HSMDA egress counter.
TEXTUAL-CONVENTION    
  Unsigned32 1..8  

TEgressHsmdaCounterIdOrZero  
The identification number of a HSMDA egress counter. The value 0 indicates an undefined counter id.
TEXTUAL-CONVENTION    
  Unsigned32 0 | 1..8  

TEgrRateModType  
The data type TEgrRateModType represents the type of egress-rate modification that is to be applied.
TEXTUAL-CONVENTION    
  INTEGER none(1), aggRateLimit(2), namedScheduler(3)  

TPolicyStatementName  
The name of a policy statement, when used as index in a table.
TEXTUAL-CONVENTION    
  TNamedItem  

TPolicyStatementNameOrEmpty  
The name of a policy statement, when an object refers to it.
TEXTUAL-CONVENTION    
  TNamedItemOrEmpty  

TLPolicyStatementNameOrEmpty  
The long name of a policy statement, when an object refers to it.
TEXTUAL-CONVENTION    
  TLNamedItemOrEmpty  

TLPolicyNameOrExpOrEmpty  
The long name of a policy statement or an expression or an empty string. A logical expression contains terms and operators and can contain sub-expressions enclosed in round brackets. A term is a string of type TPolicyStatementName. An operator can be the string 'AND', 'OR', and 'NOT'.
TEXTUAL-CONVENTION    
  TLNamedItemOrEmpty  

TXLPolicyNameOrExpOrEmpty  
The extra long name of a policy statement or an expression or an empty string. A logical expression contains terms and operators and can contain sub-expressions enclosed in round brackets. A term is a string of type TPolicyStatementName. An operator can be the string 'AND', 'OR', and 'NOT'.
TEXTUAL-CONVENTION    
  TXLNamedItemOrEmpty  

TmnxVcType  
The value of TmnxVcType is an enumerated integer that indicates a Virtual Circuit (VC) type. 'frDlciMartini(1)' replaces the old 'frDlci' when used over martini tunnels.
TEXTUAL-CONVENTION    
  INTEGER frDlciMartini(1), atmSdu(2), atmCell(3), ethernetVlan(4), ethernet(5), atmVccCell(9), atmVpcCell(10), ipipe(11), satopE1(17), satopT1(18), satopE3(19), satopT3(20), cesopsn(21), cesopsnCas(23), frDlci(25), mirrorDest(4096)  

TmnxVcId  
A 32 bit number is used to identify a VC(Virtual Circuit). The VC ID cannot be 0.
TEXTUAL-CONVENTION    
  Unsigned32 1..4294967295  

TmnxVcIdOrNone  
A 32 bit number is used to identify a VC(Virtual Circuit). A value of 0 indicates no VC ID is configured or available.
TEXTUAL-CONVENTION    
  Unsigned32 0 | 1..4294967295  

Dot1PPriority  
IEEE 802.1p priority. zero is lowest, seven is highest. -1 means not set
TEXTUAL-CONVENTION    
  Integer32 -1 | 0..7  

Dot1PPriorityMask  
IEEE 802.1p priority mask. zero is lowest, seven is highest.
TEXTUAL-CONVENTION    
  Integer32 0..7  

ServiceAccessPoint  
802.2 LLC SAP value, Source and Destination.
TEXTUAL-CONVENTION    
  Integer32 -1 | 0..255  

TLspExpValue  
MPLS Experimental bits. -1 means not set.
TEXTUAL-CONVENTION    
  Integer32 -1 | 0..7  

TIpProtocol  
IP protocol number. well known protocol numbers include ICMP(1), TCP(6), UDP(17). -1 means value not set. -2 indicates protocol wildcard for UDP and TCP.
TEXTUAL-CONVENTION    
  Integer32 -2 | -1 | 0..255  

TIpOption  
IP packet options octet. explanation of the octet bits: IP OPTION NUMBERS The Internet Protocol (IP) has provision for optional header fields identified by an option type field. Options 0 and 1 are exactly one octet which is their type field. All other options have their one octet type field, followed by a one octet length field, followed by length-2 octets of option data. The option type field is subdivided into a one bit copied flag, a two bit class field, and a five bit option number. These taken together form an eight bit value for the option type field. IP options are commonly referred to by this value. Copy Class Number Value Name Reference ---- ----- ------ ----- ------------------------------- --------- 0 0 0 0 EOOL - End of Options List [RFC791,JBP] 0 0 1 1 NOP - No Operation [RFC791,JBP] 1 0 2 130 SEC - Security [RFC1108] 1 0 3 131 LSR - Loose Source Route [RFC791,JBP] 0 2 4 68 TS - Time Stamp [RFC791,JBP] 1 0 5 133 E-SEC - Extended Security [RFC1108] 1 0 6 134 CIPSO - Commercial Security [???] 0 0 7 7 RR - Record Route [RFC791,JBP] 1 0 8 136 SID - Stream ID [RFC791,JBP] 1 0 9 137 SSR - Strict Source Route [RFC791,JBP] 0 0 10 10 ZSU - Experimental Measurement [ZSu] 0 0 11 11 MTUP - MTU Probe [RFC1191]* 0 0 12 12 MTUR - MTU Reply [RFC1191]* 1 2 13 205 FINN - Experimental Flow Control [Finn] 1 0 14 142 VISA - Experimental Access Control [Estrin] 0 0 15 15 ENCODE - ??? [VerSteeg] 1 0 16 144 IMITD - IMI Traffic Descriptor [Lee] 1 0 17 145 EIP - Extended Internet Protocol[RFC1385] 0 2 18 82 TR - Traceroute [RFC1393] 1 0 19 147 ADDEXT - Address Extension [Ullmann IPv7] 1 0 20 148 RTRALT - Router Alert [RFC2113] 1 0 21 149 SDB - Selective Directed Broadcast[Graff] 1 0 22 150 NSAPA - NSAP Addresses [Carpenter] 1 0 23 151 DPS - Dynamic Packet State [Malis] 1 0 24 152 UMP - Upstream Multicast Pkt. [Farinacci] [Note, an asterisk (*) denotes an obsoleted IP Option Number.]
TEXTUAL-CONVENTION    
  Integer32 0..255  

TTcpUdpPort  
The number of a TCP or UDP port. Well known port numbers include ftp-data(20), ftp(21), telnet(23), smtp(25), http(80), pop3(110), nntp(119), snmp(161), snmptrap(162), etc.
TEXTUAL-CONVENTION    
  Integer32 0 | 1..65535  

TOperator  
The operator specifies the manner in which a couple of other MIB objects in the table are supposed to be used. Operator Value1 Value2 ---------------------------------------------------- none(0) Any(0) Any(0) eq(1) Specified Value Any(0) range(2) Starting Value Ending Value lt(3) Specified Value Any(0) gt(4) Specified Value Any(0) 'Any(0)' specifies that, this object can accept any values but would default to 0.
TEXTUAL-CONVENTION    
  INTEGER none(0), eq(1), range(2), lt(3), gt(4)  

TTcpUdpPortOperator  
The operator used for checking on TCP/UDP ports values and ranges
TEXTUAL-CONVENTION    
  TOperator  

TFrameType  
The type of the frame for which this mac filter match criteria is defined.
TEXTUAL-CONVENTION    
  INTEGER e802dot3(0), e802dot2LLC(1), e802dot2SNAP(2), ethernetII(3), atm(5)  

TQueueId  
The value of TQueueId specifies the identification number of a queue. A value of zero (0) indicates that no specific queue identification has been assigned for this object. When an object of type TQueueId is an SNMP table index, an index value of zero (0) is not allowed and a noCreation error will be returned.
TEXTUAL-CONVENTION    
  Integer32 0 | 1..32  

TQueueIdOrAll  
The value of TQueueIdOrAll specifies the identification number of a queue A value of zero (0) indicates that no specific queue identification has been assigned for this object. A value of (-1) indicates 'all queues'.
TEXTUAL-CONVENTION    
  Integer32 -1 | 0 | 1..32  

TIngressQueueId  
The value of TIngressQueueId specifies the identification number of an ingress queue. A value of zero (0) indicates that no specific queue identification has been assigned for this object. When an object of type TIngressQueueId is an SNMP table index, an index value of zero (0) is not allowed and a noCreation error will be returned.
TEXTUAL-CONVENTION    
  Integer32 0 | 1..32  

TEgressQueueId  
The value of TEgressQueueId specifies the identification number of an egress queue. A value of zero (0) indicates that no specific queue identification has been assigned for this object. When an object of type TEgressQueueId is an SNMP table index, an index value of zero (0) is not allowed and a noCreation error will be returned.
TEXTUAL-CONVENTION    
  Integer32 0 | 1..8  

TIngressHsmdaQueueId  
The value of TIngressHsmdaQueueId specifies the identification number of a HSMDA ingress queue. A value of zero (0) indicates that no specific queue identification has been assigned for this object. When an object of type TIngressHsmdaQueueId is an SNMP table index, an index value of zero (0) is not allowed and a noCreation error will be returned.
TEXTUAL-CONVENTION    
  Integer32 0 | 1..8  

TEgressHsmdaQueueId  
The value of TEgressHsmdaQueueId specifies the identification number of a HSMDA egress queue. A value of zero (0) indicates that no specific queue identification has been assigned for this object. When an object of type TEgressHsmdaQueueId is an SNMP table index, an index value of zero (0) is not allowed and a noCreation error will be returned.
TEXTUAL-CONVENTION    
  Integer32 0 | 1..8  

THsmdaSchedulerPolicyGroupId  
The value of THsmdaSchedulerPolicyGroupId specifies the identification number of a HSMDA scheduler policy group. A value of zero (0) indicates that no specific group identification has been assigned for this object. When an object of type THsmdaSchedulerPolicyGroupId is an SNMP table index, an index value of zero (0) is not allowed and a noCreation error will be returned.
TEXTUAL-CONVENTION    
  Integer32 0 | 1..2  

THsmdaPolicyIncludeQueues  
The value of THsmdaPolicyIncludeQueues specifies which queues are to be scheduled in the same class in a HSMDA scheduler.
TEXTUAL-CONVENTION    
  INTEGER q1to2(1), q1to3(2)  

THsmdaPolicyScheduleClass  
The value of THsmdaPolicyScheduleClass the class at which the queues specified by THsmdaPolicyIncludeQueues in a HSMDA scheduler.
TEXTUAL-CONVENTION    
  Integer32 1..3  

TDSCPName  
The name of a Differential Services Code Point value.
TEXTUAL-CONVENTION    
  TNamedItem  

TDSCPNameOrEmpty  
The name of a Differential Services Code Point value.
TEXTUAL-CONVENTION    
  TNamedItemOrEmpty  

TDSCPValue  
The value of a Differential Services Code Point.
TEXTUAL-CONVENTION    
  Integer32 0..63  

TDSCPValueOrNone  
The value of a Differential Services Code Point (DSCP). A value of -1 means that no DSCP value is configured or available.
TEXTUAL-CONVENTION    
  Integer32 -1 | 0..63  

TDSCPFilterActionValue  
The value of a Differential Services Code Point. -1 means not set.
TEXTUAL-CONVENTION    
  Integer32 -1 | 0..255  

TFCName  
The name of a Forwarding Class entry.
TEXTUAL-CONVENTION    
  TNamedItem  

TFCNameOrEmpty  
The name of a Forwarding Class entry.
TEXTUAL-CONVENTION    
  TNamedItemOrEmpty  

TFCSet  
This data type describes a set of Forwarding Classes.
TEXTUAL-CONVENTION    
  BITS be(0), l2(1), af(2), l1(3), h2(4), ef(5), h1(6), nc(7)  

TFCType  
This data type enumerates the Forwarding Classes.
TEXTUAL-CONVENTION    
  INTEGER be(0), l2(1), af(2), l1(3), h2(4), ef(5), h1(6), nc(7)  

TFCTypeOrNone  
This data type enumerates the Forwarding Classes.
TEXTUAL-CONVENTION    
  INTEGER none(-1), be(0), l2(1), af(2), l1(3), h2(4), ef(5), h1(6), nc(7)  

TmnxTunnelType  
The type of this tunnel entity.
TEXTUAL-CONVENTION    
  INTEGER sdp(1), ldp(2), rsvp(3), gre(4), bypass(5), invalid(6), bgp(7)  

TmnxTunnelID  
The identifying value for a BGP-VPRN tunnel. Depending on the tunnel type the associated tunnel id may be an sdp-id, an LSP ID or zero(0).
TEXTUAL-CONVENTION    
  Unsigned32  

TmnxBgpRouteTarget  
TmnxBgpRouteTarget is an readable string that specifies the extended community name to be accepted by a Route Reflector Server or advertised by the router when reflecting any routes. I.e, it does not apply to routes that are not reflected by the router.
TEXTUAL-CONVENTION    
  OCTET STRING Size(1..32)  

TmnxVPNRouteDistinguisher  
The VPRN route distinguisher is a 8-octet object. It contains a 2-octet type field followed by a 6-octet value field. The type field specify how to interpret the value field. Type 0 specifies two subfields as a 2-octet administrative field and a 4-octet assigned number subfield. Type 1 specifies two subfields as a 4-octet administrative field which must contain an IP address and a 2-octet assigned number subfield. Type 2 specifies two subfields as a 4-octet administrative field which contains a 4-octet AS number and a 2-octet assigned number subfield.
TEXTUAL-CONVENTION    
  OCTET STRING Size(8)  

SdpBindId  
The value used to uniquely identify an SDP Binding. The first four octets correspond to the zero-extended 16-bit SDP ID, while the remaining four octets correspond to the 32-bit VC ID, both encoded in network byte order.
TEXTUAL-CONVENTION    
  OCTET STRING Size(8)  

TmnxVRtrMplsLspID  
A unique value for each Label Switched Path in the managed system. The higher range IDs are used for segment routing LSPs. The lower range IDs are used for regular LSPs.
TEXTUAL-CONVENTION    
  Unsigned32 0..65535 | 65536..131070  

TmnxVRtrMplsLspIDNoZero  
A unique value, greater than zero, for each Label Switched Path in the managed system. The higher range IDs are used for segment routing LSPs. The lower range IDs are used for regular LSPs.
TEXTUAL-CONVENTION    
  Unsigned32 1..65535 | 65536..131070  

TPortSchedulerPIR  
The Peak Information Rate (PIR) rate to be used in kbps. The value -1 means maximum rate.
TEXTUAL-CONVENTION    
  Integer32 -1 | 1..100000000  

TPortSchedulerAggRateLimitPIR  
The Peak Information Rate (PIR) rate to be used in kbps. The value -1 means maximum rate.
TEXTUAL-CONVENTION    
  Integer32 -1 | 1..800000000  

TPortSchedulerPIRRate  
The Peak Information Rate (PIR) rate to be used in kbps. The value -1 means maximum rate.
TEXTUAL-CONVENTION    
  Integer32 -1 | 1..800000000  

TPortSchedulerCIR  
The Committed Information Rate (CIR) rate to be used in kbps. The value -1 means maximum rate.
TEXTUAL-CONVENTION    
  Integer32 -1 | 0..800000000  

TWeight  
The weight of the specified entity while feeding into the parent.
TEXTUAL-CONVENTION    
  Integer32 0..100  

TWeightOverride  
The weight of the specified entity while feeding into the parent. A value of -2 specifies no override.
TEXTUAL-CONVENTION    
  Integer32 -2 | 0..100  

TNonZeroWeight  
The weight of the specified entity while feeding into the parent.
TEXTUAL-CONVENTION    
  Integer32 1..100  

TPolicerWeight  
The relative weight of the specified entity while feeding into the parent.
TEXTUAL-CONVENTION    
  Integer32 1..100  

THsWrrWeightOvr  
The THsWrrWeightOvr data type specifies the override weight of the corresponding HS queue feeding into its parent WRR scheduler. A value of -2 specifies no override.
TEXTUAL-CONVENTION    
  Integer32 -2 | 1..127  

THsClassWeightOverride  
The THsClassWeightOverride data type specifies the weight of the corresponding HS class feeding into its parent shaper. A value of -2 specifies no override.
TEXTUAL-CONVENTION    
  Integer32 -2 | 1 | 2 | 4 | 8  

THsmdaWeight  
The weight of the specified HSMDA entity while feeding into the parent.
TEXTUAL-CONVENTION    
  Integer32 1..100  

THsmdaWrrWeight  
The weight of the specified HSMDA entity while feeding into the parent.
TEXTUAL-CONVENTION    
  Integer32 1..32  

THsmdaWeightClass  
The weight of the specified HSMDA entity while feeding into the parent.
TEXTUAL-CONVENTION    
  INTEGER class1(1), class2(2), class4(4), class8(8)  

THsmdaWeightOverride  
The weight of the specified HSMDA entity while feeding into the parent. A value of -2 specifies no override.
TEXTUAL-CONVENTION    
  Integer32 -2 | 1..100  

THsmdaWrrWeightOverride  
The weight of the specified HSMDA entity while feeding into the parent. A value of -2 specifies no override.
TEXTUAL-CONVENTION    
  Integer32 -2 | 1..32  

TCIRRate  
The CIR rate to be used in kbps. The value -1 means maximum rate.
TEXTUAL-CONVENTION    
  Integer32 -1 | 0..100000000  

THPolCIRRate  
The CIR rate to be used in kbps. The value -1 means maximum rate.
TEXTUAL-CONVENTION    
  Integer32 -1 | 0..2000000000  

TRateType  
The type of the PIR/CIR rate. The value 'kbps' means the rate is specified in kbps. The value 'percent' means the rate is specified in percentage
TEXTUAL-CONVENTION    
  INTEGER kbps(1), percent(2)  

TBWRateType  
The type of the PIR/CIR percent rate. The value 'kbps' means the rate is specified in kbps. The value 'percentPortLimit' means the rate is specified in percentage of port limit. The value 'percentLocalLimit' means the rate is specified in percentage of local limit.
TEXTUAL-CONVENTION    
  INTEGER kbps(1), percentPortLimit(2), percentLocalLimit(3)  

TPSPRateType  
The type of the PIR/CIR rate being applied to port scheduler policy. The value of 'kbps' means the rate is specified in kbps. The value of 'percentActivePortLimit' means the rate is specified in percentage of active port bandwidth, that is, bandwidth of active ports in a LAG.
TEXTUAL-CONVENTION    
  INTEGER kbps(1), percentLocal(2), percentLagActive(3)  

TPolicerRateType  
The type of the PIR/CIR percent rate. The value 'kbps' means the rate is specified in kbps. The value 'percentLocalLimit' means the rate is specified in percentage of local limit.
TEXTUAL-CONVENTION    
  INTEGER kbps(1), percentLocalLimit(2)  

TCIRRateOverride  
The CIR rate to be used in kbps. The value -1 means maximum rate. A value of -2 specifies no override.
TEXTUAL-CONVENTION    
  Integer32 -2 | -1 | 0..100000000  

THPolCIRRateOverride  
The CIR rate to be used in kbps. The value -1 means maximum rate. A value of -2 specifies no override.
TEXTUAL-CONVENTION    
  Integer32 -2 | -1 | 0..2000000000  

TCIRPercentOverride  
The CIR percentage rate specified in hundredths of a percent. A value of -2 specifies no override.
TEXTUAL-CONVENTION    
  Integer32 -2 | 0..10000  

THsmdaCIRKRate  
The HSMDA CIR rate to be used in Kbps. The value -1 means maximum rate.
TEXTUAL-CONVENTION    
  Integer32 -1 | 0..100000000  

THsmdaCIRKRateOverride  
The HSMDA CIR rate to be used in Kbps. The value -1 means maximum rate. A value of -2 specifies no override.
TEXTUAL-CONVENTION    
  Integer32 -2 | -1 | 0..100000000  

THsmdaCIRMRate  
The HSMDA CIR rate to be used in Mbps. The value -1 means maximum rate.
TEXTUAL-CONVENTION    
  Integer32 -1 | 0..100000  

THsmdaCIRMRateOverride  
The HSMDA CIR rate to be used in Mbps. The value -1 means maximum rate. A value of -2 specifies no override.
TEXTUAL-CONVENTION    
  Integer32 -2 | -1 | 0..100000  

TPIRRate  
The PIR rate to be used in kbps. The value -1 means maximum rate.
TEXTUAL-CONVENTION    
  Integer32 -1 | 1..100000000  

THPolVirtualSchePIRRate  
The PIR rate to be used in kbps. The value -1 means maximum rate.
TEXTUAL-CONVENTION    
  Integer32 -1 | 1..800000000  

THPolVirtualScheCIRRate  
The CIR rate to be used in kbps. The value -1 means maximum rate.
TEXTUAL-CONVENTION    
  Integer32 -1 | 0..800000000  

TAdvCfgRate  
The PIR rate to be used in kbps.
TEXTUAL-CONVENTION    
  Integer32 0..100000000  

TMaxDecRate  
The Advanced Configuration policy Max-Decrement rate to be used in kbps.
TEXTUAL-CONVENTION    
  Integer32 0 | 1..100000000  

THPolPIRRate  
The PIR rate to be used in kbps. The value -1 means maximum rate.
TEXTUAL-CONVENTION    
  Integer32 -1 | 1..2000000000  

TSecondaryShaper10GPIRRate  
The secondary shaper PIR rate to be used in Mbps. The value -1 means maximum rate.
TEXTUAL-CONVENTION    
  Integer32 -1 | 1..10000  

TExpSecondaryShaperPIRRate  
The expanded secondary shaper PIR rate to be used in Kbps. The value -1 means maximum rate.
TEXTUAL-CONVENTION    
  Integer32 -1 | 1..10000000  

TExpSecondaryShaperClassRate  
The expanded secondary shaper class PIR rate to be used in Kbps. The value -1 means maximum rate.
TEXTUAL-CONVENTION    
  Integer32 -1 | 1..10000000  

TPIRRateOverride  
The PIR rate to be used in kbps. The value -1 means maximum rate. A value of -2 specifies no override.
TEXTUAL-CONVENTION    
  Integer32 -2 | -1 | 1..100000000  

TPIRAggRateLimitOverride  
The PIR rate to be used in kbps. The value -1 means maximum rate. A value of -2 specifies no override.
TEXTUAL-CONVENTION    
  Integer32 -2 | -1 | 1..800000000  

THPolPIRRateOverride  
The PIR rate to be used in kbps. The value -1 means maximum rate. A value of -2 specifies no override.
TEXTUAL-CONVENTION    
  Integer32 -2 | -1 | 1..2000000000  

TPIRPercentOverride  
The PIR percentage rate specified in hundredths of a percent. A value of -2 specifies no override.
TEXTUAL-CONVENTION    
  Integer32 -2 | 1..10000  

TPIRRateOrZero  
The PIR rate to be used in kbps. The value -1 means maximum rate. The value 0 means undefined rate.
TEXTUAL-CONVENTION    
  Integer32 -1 | 0..100000000  

THsmdaPIRKRate  
The HSMDA PIR rate to be used in Kbps. The value -1 means maximum rate.
TEXTUAL-CONVENTION    
  Integer32 -1 | 1..100000000  

THsmdaPIRKRateOverride  
The HSMDA PIR rate to be used in Kbps. The value -1 means maximum rate. A value of -2 specifies no override.
TEXTUAL-CONVENTION    
  Integer32 -2 | -1 | 1..100000000  

THsmdaPIRMRate  
The HSMDA PIR rate to be used in Mbps. The value -1 means maximum rate.
TEXTUAL-CONVENTION    
  Integer32 -1 | 1..100000  

THsmdaPIRMRateOverride  
The HSMDA PIR rate to be used in Mbps. The value -1 means maximum rate. A value of -2 specifies no override.
TEXTUAL-CONVENTION    
  Integer32 -2 | -1 | 1..100000  

TmnxDHCP6MsgType  
The DHCP6 messagetype.
TEXTUAL-CONVENTION    
  INTEGER dhcp6MsgTypeSolicit(1), dhcp6MsgTypeAdvertise(2), dhcp6MsgTypeRequest(3), dhcp6MsgTypeConfirm(4), dhcp6MsgTypeRenew(5), dhcp6MsgTypeRebind(6), dhcp6MsgTypeReply(7), dhcp6MsgTypeRelease(8), dhcp6MsgTypeDecline(9), dhcp6MsgTypeReconfigure(10), dhcp6MsgTypeInfoRequest(11), dhcp6MsgTypeRelayForw(12), dhcp6MsgTypeRelayReply(13), dhcp6MsgTypeLeasequery(14), dhcp6MsgTypeLeasequeryReply(15)  

TmnxIgpInstance  
An object of type TmnxIgpInstance identifies an instance of an Interior Gateway Protocol (IGP). Supported IGPs are Intermediate System to Intermediate System (IS-IS) and Open Shortest Path First (OSPF). The supported range varies with the IGP and address family, as follows. IGP Address Family Supported Range ------ -------------- --------------- IS-IS all 0..31 OSPFv2 all 0..31 OSPFv3 IPv4 unicast 64..95 OSPFv3 IPv6 unicast 0..31
TEXTUAL-CONVENTION    
  Unsigned32 0..31 | 64..95  

TmnxOspfInstance  
A number used to identify an instance of OSPF, For OSPFv2 only 0..31 is supported, For OSPFv3 the range is divided in address families as follows: 0..31 ipv6-unicast address family (supported) 32..63 ipv6-multicast address family (not supported) 64..95 ipv4-unicast address family (supported) 96..127 ipv4-multicast address family (not supported)
TEXTUAL-CONVENTION    
  Unsigned32 0..127  

TmnxBGPFamilyType  
The value of TmnxBGPFamilyType specifies the AFI-SAFI family for BGP peer.
TEXTUAL-CONVENTION    
  BITS ipv4Unicast(0), ipv4Multicast(1), ipv4UastMcast(2), ipv4MplsLabel(3), ipv4Vpn(4), ipv6Unicast(5), ipv6Multicast(6), ipv6UcastMcast(7), ipv6MplsLabel(8), ipv6Vpn(9), l2Vpn(10), ipv4Mvpn(11), msPw(12), ipv4Flow(13), mdtSafi(14), routeTarget(15), mcastVpnIpv4(16), mvpnIpv6(17), ipv6Flow(18), evpn(19), bgpLs(20), mcastVpnIpv6(21)  

TmnxIgmpGroupFilterMode  
The data type TmnxIgmpGroupFilterMode describes the filter-mode of a group. In 'include(1)' mode, reception of packets sent to the specified multicast address is requested only from those IPv4 Source addresses listed in the corresponding source-list. In 'exclude(2)' mode, reception of packets sent to the given multicast address is requested from all IPv4 Source addresses, except those listed in the corresponding source-list (if any).
TEXTUAL-CONVENTION    
  INTEGER include(1), exclude(2)  

TmnxIgmpGroupType  
The data type TmnxIgmpGroupType describes how a multicast group is learned.
TEXTUAL-CONVENTION    
  INTEGER static(1), dynamic(2)  

TmnxIgmpVersion  
The data type TmnxIgmpVersion denotes the version of the IGMP protocol: - 'version1(1)': means version 1 of the IGMP protocol - 'version2(2)': means version 2 of the IGMP protocol - 'version3(3)': means version 3 of the IGMP protocol.
TEXTUAL-CONVENTION    
  INTEGER version1(1), version2(2), version3(3)  

TmnxMldGroupFilterMode  
The data type TmnxMldGroupFilterMode describes the filter-mode of a group. In 'include(1)' mode, reception of packets sent to the specified multicast address is requested only from those IPv6 source addresses listed in the corresponding source-list. In 'exclude(2)' mode, reception of packets sent to the given multicast address is requested from all IPv6 source addresses, except those listed in the corresponding source-list (if any).
TEXTUAL-CONVENTION    
  INTEGER include(1), exclude(2)  

TmnxMldGroupType  
The data type TmnxMldGroupType describes how a multicast group is learned.
TEXTUAL-CONVENTION    
  INTEGER static(1), dynamic(2)  

TmnxMldVersion  
The data type TmnxMldVersion denotes the version of the MLD protocol: - 'version1(1)': means version 1 of the MLD protocol - 'version2(2)': means version 2 of the MLD protocol
TEXTUAL-CONVENTION    
  INTEGER version1(1), version2(2)  

TmnxManagedRouteStatus  
The data type TmnxManagedRouteStatus denotes the status of a Managed Route.
TEXTUAL-CONVENTION    
  INTEGER installed(0), notYetInstalled(1), wrongAntiSpoofType(2), outOfMemory(3), shadowed(4), routeTableFull(5), parentInterfaceDown(6), hostInactive(7), enhancedSubMgmtRequired(8), deprecated1(9), l2AwNotSupported(10), nextHopLimitExceeded(11), notApplicable(12), noNextHop(13), gtpNotSupported(14)  

TmnxTunnelTypeExt  
The type of this tunnel entity.
TEXTUAL-CONVENTION    
  INTEGER invalid(1), sdp(2), rsvp(3), ldp(4), ospf(5), isis(6), bypass(7), gre(8), bgp(9), srTe(10), fpe(11), udp(12)  

TmnxIgpSCFamilyType  
The data type to specify IGP shortcut tunnel next hop family.
TEXTUAL-CONVENTION    
  INTEGER ipv4(0), ipv6(1), srv4(2), srv6(3)  

TmnxAdjacencySetFamilyType  
The data type to specify Adjacency Set family.
TEXTUAL-CONVENTION    
  INTEGER ipv4(0), ipv6(1)  

TmnxAncpString  
The TmnxAncpString data type contains a valid ancp string.
TEXTUAL-CONVENTION    
  DisplayString Size(1..63)  

TmnxAncpStringOrZero  
The TmnxAncpStringOrZero data type contains a valid ancp string. An empty string indicates that no ANCP string is defined.
TEXTUAL-CONVENTION    
  DisplayString Size(0..63)  

TmnxMulticastAddrFamily  
The data type TmnxMulticastAddrFamily denotes the family for multicast protocol.
TEXTUAL-CONVENTION    
  INTEGER ipv4Multicast(0), ipv6Multicast(1)  

TmnxNatIsaGrpId  
The TmnxNatIsaGrpId data type contains an identification number for a Network Address Translation Integrated Service Adaptor group.
TEXTUAL-CONVENTION    
  Unsigned32 1..4  

TmnxNatIsaGrpIdOrZero  
The TmnxNatIsaGrpIdOrZero data type contains an identification number for a Network Address Translation Integrated Service Adaptor (ISA) group. The value zero means that no NAT ISA Group is defined.
TEXTUAL-CONVENTION    
  Unsigned32 0..4  

TmnxNatSubscriberType  
TmnxNatSubscriberType is an enumerated integer that specifies the NAT subscriber type. The possible values are 'classicLsnSub' and 'dsliteLsnSub' for classic and Dual Stack Lite Large Scale NAT subscribers respectively, 'l2AwareSub' for Layer-2-Aware NAT subscribers, and 'nat64LsnSub' for NAT-64 subscribers respectively.
TEXTUAL-CONVENTION    
  INTEGER l2AwareSub(1), classicLsnSub(2), dsliteLsnSub(3), nat64LsnSub(4)  

TmnxNatSubscriberTypeOrNone  
TmnxNatSubscriberTypeOrNone is an enumerated integer that specifies the NAT subscriber type. The value 'none' indicates that NAT subscriber type is not specified. The values 'classicLsnSub' and 'dsliteLsnSub' are for classic and Dual Stack Lite Large Scale NAT subscribers respectively. The value 'l2AwareSub' is for Layer-2-Aware NAT subscribers, and the value 'nat64LsnSub' is for NAT-64 subscribers.
TEXTUAL-CONVENTION    
  INTEGER none(0), l2AwareSub(1), classicLsnSub(2), dsliteLsnSub(3), nat64LsnSub(4)  

TmnxAuthPassword  
The TmnxAuthPassword data type contains a password used for authentication of subscribers.
TEXTUAL-CONVENTION    
  DisplayString Size(0..64)  

TmnxAsciiSpecification  
The data type TmnxAsciiSpecification is a format string that specifies how to form a target ASCII string. The format is as follows: ::= + ::= | ::= '%' refers to a printable ASCII character. Examples and supported char-origin specifiers are supplied with the object definitions.
TEXTUAL-CONVENTION    
  DisplayString Size(0..255)  

TmnxMacSpecification  
The data type TmnxMacSpecification is a string of ASCII characters that specifies how to format a string that represents a MAC address. The format is as follows: ::= [] ::= + | + ::= 'A' | 'B' | 'B' ... | 'Z' ::= 'a' | 'b' | 'c' ... | 'z' any ASCII character that is not an or a decimal digit Only the number of alphabetic characters and the case is relevant. Examples: 'ab:' 00:0c:f1:99:85:b8 Nokia SROS style 'XY-' 00-0C-F1-99-85-B8 IEEE canonical style 'mmmm.' 0002.03aa.abff Cisco style. 'xx' 000cf19985b8
TEXTUAL-CONVENTION    
  DisplayString Size(0..17)  

TmnxBinarySpecification  
The data type TmnxBinarySpecification is a string of ASCII characters that specifies how to form a binary number. The format is as follows: ::= + ::= '0' | '1' | ::= '*' ::= [1..32] Examples and supported bit-origin specifiers are supplied with the object definitions.
TEXTUAL-CONVENTION    
  DisplayString Size(0..255)  

TmnxDefSubIdSource  
The data type TmnxDefSubIdSource specifies what will be used as the default subscriber identification. This value is used in case no other source (like RADIUS) provides a subscriber identification string. If the value of this object is set to 'useSapId', the SAP-id will be used as the default subscriber identification string. If the value of this object is set to 'useAutoId', the auto-generated subscriber identification string, as defined in tmnxSubMgmtAutoSubIdObjs, is used as the default subscriber identification string. If the value of this object is set to 'useString', the value of the string contained in another object will be used as the default subscriber identification string; that object must be identified where this datatype is used.
TEXTUAL-CONVENTION    
  INTEGER useSapId(1), useString(2), useAutoId(3)  

TmnxSubAuthPlcyUserNameOp  
The TmnxSubAuthPlcyUserNameOp data type is an enumerated integer that specifies the operation to perform on the user-name before sending it to the RADIUS server.
TEXTUAL-CONVENTION    
  INTEGER noOperation(0), appendDomain(1), stripDomain(2), replaceDomain(3), defaultDomain(4)  

TmnxSubCallingStationIdType  
The TmnxSubCallingStationIdType data type is an enumerated integer that specifies what string will be put in the RADIUS or DIAMETER Calling-Station-Id attribute: - sapString (1): the value of TIMETRA-SAP-MIB::sapCallingStationId of the subscriber host SAP; - mac (2): the subscriber host MAC address, formatted as a lower case ASCII string with octet values separated by a ':'; - sapId (3): the subscriber host SAP identifier, formatted as an ASCII string. - remoteId (4): the intermediate agent Remote ID as received by means of, for example, a PPPoE vendor-specific tag, a DHCP Agent Remote ID Sub-option or an L2TP Access Line Agent-Remote-Id AVP. - llid (5): the logical link identifier as received during pre-authentication.
TEXTUAL-CONVENTION    
  INTEGER sapString(1), mac(2), sapId(3), remoteId(4), llid(5)  

TmnxSubAcctSessionId  
The data type TmnxSubAcctSessionId contains a string that identifies a subscriber for the purposes of accounting.
TEXTUAL-CONVENTION    
  DisplayString Size(0..22)  

TmnxSubIdentString  
The data type TmnxSubIdentString denotes the subscriber identification string.
TEXTUAL-CONVENTION    
  DisplayString Size(1..32)  

TmnxSubIdentStringOrEmpty  
The data type TmnxSubIdentStringOrEmpty denotes the subscriber identification string. The empty string denotes the absence of a subscriber identification string.
TEXTUAL-CONVENTION    
  DisplayString Size(0..32)  

TmnxSubRadServAlgorithm  
The TmnxSubRadServAlgorithm data type is an enumerated integer that indicates the algorithm used to access the list of configured RADIUS servers: - direct (1): The first server will be used as primary server for all requests, the second as secondary and so on. - roundRobin (2): The first server will be used as primary server for the first request, the second server as primary for the second request, and so on. If the router gets to the end of the list, it starts again with the first server. - hashBased (3): The server will be selected based on a specified hash value.
TEXTUAL-CONVENTION    
  INTEGER direct(1), roundRobin(2), hashBased(3)  

TmnxSubRadiusAttrType  
The TmnxSubRadiusAttrType data type contains a number that indicates a RADIUS attribute type.
TEXTUAL-CONVENTION    
  Unsigned32 0..255  

TmnxSubRadiusVendorId  
The TmnxSubRadiusVendorId data type contains a number that indicates a RADIUS Vendor-Id.
TEXTUAL-CONVENTION    
  Unsigned32 0..16777215  

TmnxSubRadiusDisplayString  
The TmnxSubRadiusOctetString data type contains a character string that corresponds to a Radius attribute.
TEXTUAL-CONVENTION    
  DisplayString Size(0..253)  

TmnxSubRadiusOctetString  
The TmnxSubRadiusOctetString data type contains an octet string that corresponds to a Radius attribute
TEXTUAL-CONVENTION    
  OCTET STRING Size(253)  

TmnxSubSlaMode  
The TmnxSubSlaMode data type is an enumerated integer that specifies the handling of SLA profile instances for a subscriber. - Expanded sla-mode: a subscriber is allowed to have multiple SLA profile instances, using different SLA profiles and/or different VLANs. - Single sla-mode: only 1 single SLA profile instance is allowed for a subscriber. This restriction has 2 implications: - Last SLA profile wins: if a new host is added with an SLA profile that is different from the existing hosts of the subscriber, or an existing host is changed to use a different SLA profile, then all existing hosts of that subscriber will be changed to the new SLA profile. - First VLAN wins: All hosts of a subscriber must use the same VLAN, i.e. a new host on different VLAN is rejected.
TEXTUAL-CONVENTION    
  INTEGER expanded(0), single(1)  

TmnxRadiusPendingReqLimit  
The TmnxRadiusPendingReqLimit data type is a number that specifies the limit to the number of pending RADIUS request messages.
TEXTUAL-CONVENTION    
  Unsigned32 1..4096  

TmnxRadiusServerOperState  
The TmnxRadiusServerOperState data type is an enumerated integer that describes the values used to identify the operational state of a RADIUS server.
TEXTUAL-CONVENTION    
  INTEGER unknown(1), inService(2), outOfService(3), transition(4), overloaded(5), probing(6)  

TmnxSubShcvAction  
The TmnxSubShcvAction data type is an enumerated integer that describes the values used to identify the action taken when Subscriber Host Connectivity Verification (SHCV) failed.
TEXTUAL-CONVENTION    
  INTEGER alarm(1), remove(2)  

TmnxSubShcvInterval  
The TmnxSubShcvInterval data type is a number that specifies the interval in minutes between connectivity checks. The value zero means no connectivity checking.
TEXTUAL-CONVENTION    
  Unsigned32 0..6000  

TmnxSubShcvRetryCount  
The TmnxSubShcvRetryTimeout data type is a number that specifies the number of connectivity check retransmissions. Setting the value to n specifies that, for any given host, at most (n+1) probes are done each interval, and (n+1) missed replies are considered as a connectivity failure.
TEXTUAL-CONVENTION    
  Unsigned32 2..29  

TmnxSubShcvRetryTimeout  
The TmnxSubShcvRetryTimeout data type is a number that specifies the timeout in seconds before a connectivity check retransmission.
TEXTUAL-CONVENTION    
  Unsigned32 10..60  

TmnxSubShcvSrcIpOrigin  
The TmnxSubShcvSrcIpOrigin data type is an enumerated integer that describes the values used to identify the origin of the source IP address used for connectivity verification in a layer-3 service (IES or VPRN). The value 'interface' means that the IP address of the interface is used. The value 'vrrp' means that the primary IP address of the Virtual Router Redundancy Protocol (VRRP) is used.
TEXTUAL-CONVENTION    
  INTEGER interface(1), vrrp(2)  

TmnxReferenceBandwidth  
The TmnxRadiusPendingReqLimit data type is a number that specifies the reference bandwidth used for cost calculation. The formula is: Cost = reference-bandwidth / bandwidth. The unit is 1000 bps. The value zero specifies that no reference-bandwidth is configured.
TEXTUAL-CONVENTION    
  Unsigned32 0..4000000000  

TmnxSubProfileString  
The data type TmnxSubProfileString denotes the subscriber profile string.
TEXTUAL-CONVENTION    
  DisplayString Size(1..16)  

TmnxSubProfileStringOrEmpty  
The data type TmnxSubProfileStringOrEmpty denotes the subscriber profile string. The empty string denotes the absence of a subscriber profile.
TEXTUAL-CONVENTION    
  DisplayString Size(0..16)  

TmnxSlaProfileString  
The data type TmnxSlaProfileString denotes the SLA profile string.
TEXTUAL-CONVENTION    
  DisplayString Size(1..16)  

TmnxSlaProfileStringOrEmpty  
The data type TmnxSlaProfileStringOrEmpty denotes the SLA profile string. The empty string denotes the absence of a SLA profile.
TEXTUAL-CONVENTION    
  DisplayString Size(0..16)  

TmnxAppProfileString  
The data type TmnxAppProfileString denotes the application profile string.
TEXTUAL-CONVENTION    
  DisplayString Size(1..16)  

TmnxAppProfileStringOrEmpty  
The data type TmnxAppProfileStringOrEmpty denotes the application profile string. The empty string denotes the absence of a application profile.
TEXTUAL-CONVENTION    
  DisplayString Size(0..16)  

TmnxSubMgtIntDestIdOrEmpty  
The data type TmnxSubMgtIntDestIdOrEmpty denotes the intermediate destination id. The empty string denotes the absence of an intermediate destination id.
TEXTUAL-CONVENTION    
  DisplayString Size(0..32)  

TmnxSubMgtIntDestId  
The data type TmnxSubMgtIntDestId denotes the intermediate destination id.
TEXTUAL-CONVENTION    
  TmnxSubMgtIntDestIdOrEmpty Size(1..32)  

TmnxDefInterDestIdSource  
The data type TmnxDefInterDestIdSource specifies what will be used as the default intermediate destination identifier. This value is used in case no other source (like RADIUS) provides an intermediate destination identifier. If the value of this object is set to 'useString', the value of the string contained in another object will be used as the default intermediate destination identifier; that object must be identified where this datatype is used. If the value of this object is set to 'useTopQTag', the top q-tag of the ingress SAP will be used as the default subscriber intermediate destination identifier. If the value of this object is set to 'useVpi', the ATM VPI of the ingress SAP will be used as the default subscriber intermediate destination identifier.
TEXTUAL-CONVENTION    
  INTEGER useString(1), useTopQTag(2), useVpi(3)  

TmnxSubNasPortSuffixType  
The TmnxSubNasPortSuffixType data type is an enumerated integer that specifies what suffix will be added to the RADIUS NAS-Port attribute: - none (0): No suffix will be added. - circuitId (1): If available, the circuit-id will be added. - remoteId (2): If available, the remote-id will be added.
TEXTUAL-CONVENTION    
  INTEGER none(0), circuitId(1), remoteId(2)  

TmnxSubNasPortPrefixType  
The TmnxSubNasPortPrefixType data type is an enumerated integer that specifies what prefix will be added to the RADIUS NAS-Port attribute: - none (0): No prefix will be added. - userString (1): A user configurable string will be added.
TEXTUAL-CONVENTION    
  INTEGER none(0), userString(1)  

TmnxSubNasPortTypeType  
The TmnxSubNasPortTypeType data type is an enumerated integer that specifies what value will be put in the NAS-Port-Type attribute of RADIUS or DIAMETER messages: - standard (1): according to the RADIUS specification RFC 2865 section 5.41 NAS-Port-Type and RFC 4603 Additional Values for the NAS-Port-Type Attribute; - config (2): a configured value.
TEXTUAL-CONVENTION    
  INTEGER standard(1), config(2)  

TmnxSubCreditVolumeUnit  
The TmnxSubCreditVolumeUnit data type is an enumerated integer that specifies the unit in which the volume-credit is expressed.
TEXTUAL-CONVENTION    
  INTEGER bytes(0), kilobytes(1), megabytes(2), gigabytes(3)  

TmnxPccRuleFilterForwardAction  
The TmnxPccRuleFilterForwardAction data type is an enumerated integer that specifies the filter action taken in a PCC rule. The value redirNhOrFwd (5) means: forward to the specified next hop, but if no next-hop ip address or service id is given then just forward.
TEXTUAL-CONVENTION    
  INTEGER none(0), forward(1), drop(2), redirUrl(3), redirNh(4), redirNhOrFwd(5)  

TmnxPccRuleQosForwardAction  
The TmnxPccRuleQosForwardAction data type is an enumerated integer that specifies the qos action taken in a PCC rule.
TEXTUAL-CONVENTION    
  BITS rateLimit(0), fcRemark(1), monitor(2), account(3), forward(4)  

TmnxRadiusFramedRouteMetric  
The TmnxRadiusFramedRouteMetric data type is a number that represents the value of the metric in a RADIUS Framed-Route option Text field.
TEXTUAL-CONVENTION    
  Unsigned32 0..65535  

TmnxRadiusFramedRoutePreference  
The TmnxRadiusFramedRouteMetric data type is a number that represents the value of the preference in a RADIUS Framed-Route option Text field.
TEXTUAL-CONVENTION    
  Unsigned32 0..255  

TmnxRadiusFramedRouteTag  
The TmnxRadiusFramedRouteMetric data type is a number that represents the value of the tag in a RADIUS Framed-Route option Text field.
TEXTUAL-CONVENTION    
  Unsigned32 0..4294967295  

TmnxSubMgtOrgStrOrZero  
The data type TmnxSubMgtOrgStrOrZero denotes the organization string. The empty string denotes the absence of an organization string.
TEXTUAL-CONVENTION    
  DisplayString Size(0..32)  

TmnxSubMgtOrgString  
The data type TmnxSubMgtOrgStrOrZero denotes the organization string.
TEXTUAL-CONVENTION    
  TmnxSubMgtOrgStrOrZero Size(1..32)  

TmnxFilterProfileStringOrEmpty  
The data type TmnxFilterProfileStringOrEmpty denotes the filter profile string. The empty string denotes the absence of a filter profile.
TEXTUAL-CONVENTION    
  DisplayString Size(0..16)  

TmnxFpeId  
The data type TmnxFpeId is a number that uniquely identifies a Forward Path Extension (FPE).
TEXTUAL-CONVENTION    
  Unsigned32 1..64  

TmnxFpeIdOrZero  
The data type TmnxFpeIdOrZero is a number that either uniquely identifies a Forward Path Extension (FPE), or is equal to zero.
TEXTUAL-CONVENTION    
  Unsigned32 0..64  


TmnxAccessLoopEncaps1  
The data type TmnxAccessLoopEncaps1 specifies the encapsulation used by the subscriber on the DSL access loop.
TEXTUAL-CONVENTION    
  INTEGER notAvailable(0), untaggedEthernet(1), singleTaggedEthernet(2)  

TmnxAccessLoopEncaps2  
The data type TmnxAccessLoopEncaps2 specifies the encapsulation used by the subscriber on the DSL access loop.
TEXTUAL-CONVENTION    
  INTEGER notAvailable(0), pppoaLlc(1), pppoaNull(2), ipoaLlc(3), ipoaNull(4), ethernetOverAal5LlcFcs(5), ethernetOverAal5LlcNoFcs(6), ethernetOverAal5NullFcs(7), ethernetOverAal5NullNoFcs(8)  

TmnxSubAleOffsetMode  
The data type TmnxSubAleOffsetMode specifies the way the encapsulation offset of the subscriber in the DSL access loop is learned by the 7xxx system. This offset is used in 7xxx egress shaping, adjusting the subscriber aggregate rate to account for the fixed encapsulation offset and per packet variable expansion of the last mile for the specific session used by the subscriber host. The value 'none' disables the adjustment. While the value is 'auto', the encapsulation offset will be learned for example from the encapsulation type value signaled in the Access-loop-encapsulation sub-TLV in the Vendor-Specific PPPoE Tags or DHCP Relay Options [rfc4679].
TEXTUAL-CONVENTION    
  INTEGER none(0), auto(1)  

TmnxSubAleOffset  
The data type TmnxSubAleOffset specifies the encapsulation offset value of the subscriber in the DSL access loop as used by the 7xxx system. This offset is used in 7xxx egress shaping in order to accurately shape the end user payload.
TEXTUAL-CONVENTION    
  INTEGER none(0), pppoaLlc(1), pppoaNull(2), pppoeoaLlc(3), pppoeoaLlcFcs(4), pppoeoaLlcTagged(5), pppoeoaLlcTaggedFcs(6), pppoeoaNull(7), pppoeoaNullFcs(8), pppoeoaNullTagged(9), pppoeoaNullTaggedFcs(10), ipoaLlc(11), ipoaNull(12), ipoeoaLlc(13), ipoeoaLlcFcs(14), ipoeoaLlcTagged(15), ipoeoaLlcTaggedFcs(16), ipoeoaNull(17), ipoeoaNullFcs(18), ipoeoaNullTagged(19), ipoeoaNullTaggedFcs(20), pppoe(21), pppoeTagged(22), ipoe(23), ipoeTagged(24)  

TmnxDhcpOptionType  
The data type TmnxDhcpOptionType represents how the value of this option is encoded: - 'ipv4 (1)' : this option contains an IPv4 address (4 octets) - 'ascii(2)' : this option contains seven-bit ASCII characters - 'hex (3)' : this option contains octets. It must be displayed in hexadecimal format because it contains non-printable characters. - 'ipv6 (4)' : this option contains an IPv6 address (16 octets) - 'domain (5)': this option contains a domain name that will be encoded as specified by RFC 1035 section 3.1.
TEXTUAL-CONVENTION    
  INTEGER ipv4(1), ascii(2), hex(3), ipv6(4), domain(5)  

TmnxDhcpServerDUIDTypeCode  
The data type TmnxDhcpServerDUIDTypeCode represents the type code of the DHCP Unique Identifier (DUID) as specified by RFC 3315 section 9.1.
TEXTUAL-CONVENTION    
  INTEGER duidEnterprise(2), duidLinkLocal(3)  

TmnxPppoeUserName  
The data type TmnxPppoeUserName denotes the PPPoE username.
TEXTUAL-CONVENTION    
  DisplayString Size(1..253)  

TmnxPppoeUserNameOrEmpty  
The data type TmnxPppoeUserNameOrEmpty denotes the PPPoE username.
TEXTUAL-CONVENTION    
  DisplayString Size(0..253)  

TCpmProtPolicyID  
The data type TCpmProtPolicyID represents the identification number of a CPM Protection policy. The value '0' indicates that no CPM Protection policy is provisioned.
TEXTUAL-CONVENTION    
  Unsigned32 0..255  

TCpmProtPolicyIDOrDefault  
The data type TCpmProtPolicyIDOrDefault represents the identification number of a CPM Protection policy. The value of '-1' indicates the system determined default value.
TEXTUAL-CONVENTION    
  Integer32 -1 | 1..255  

TMlpppQoSProfileId  
This textual convention uniquely identifies MLPPP Bundle QoS profile in the ingress and egress MLPPP QoS profile tables. The value 0 indicates default MLPPP QoS Profile as applicable to a given H/W
TEXTUAL-CONVENTION    
  Unsigned32 0..65535  

TMcFrQoSProfileId  
This textual convention uniquely identifies Multi-class Frame relay QoS profiles in the ingress and egress multi-class frame relay QoS profile tables. The value 0 indicates a default QoS Profile as applicable to a given hardware.
TEXTUAL-CONVENTION    
  Unsigned32 0..65535  

TmnxPppoeSessionId  
The TmnxPppoeSessionId indicates the 16 bit wide PPPoE session Id.
TEXTUAL-CONVENTION    
  Unsigned32 0..65535  

TmnxPppoePadoDelay  
The data type TmnxPppoePadoDelay specifies the delay timeout in deci-seconds before sending a PADO (PPPoE Active Discovery Offer).
TEXTUAL-CONVENTION    
  Unsigned32 0 | 1..30  

TmnxPppoeSessionInfoOrigin  
The TmnxPppoeSessionInfoOrigin indicates the originator of the provided information.
TEXTUAL-CONVENTION    
  INTEGER none(0), default(1), radius(2), localUserDb(3), dhcp(4), midSessionChange(5), tags(6), l2tp(7), localPool(8), diameterNasreq(9), diameterGx(10), gtp(11), python(12), bonding(13)  

TmnxPppoeSessionType  
The TmnxPppoeSessionType indicates the type of PPPoE session.
TEXTUAL-CONVENTION    
  INTEGER local(1), localWholesale(2), localRetail(3), l2tp(4)  

TmnxPppNcpProtocol  
The TmnxPppNcpProtocol data type represents the PPP Network Control Protocol.
TEXTUAL-CONVENTION    
  INTEGER ipcp(1), ipv6cp(2)  

TmnxDiamCcFailureHndlng  
The TmnxDiamCcFailureHndlng data type is an enumerated integer that describes the different actions that can be taken after a DCCA (Diameter Credit Control Application) session failure has occurred.
TEXTUAL-CONVENTION    
  INTEGER terminate(1), continue(2), retryAndTerminate(3)  

TmnxMlpppEpClass  
The TmnxMlpppEpClass type represents the address class of the MLPPP Endpoint Discriminator option.
TEXTUAL-CONVENTION    
  INTEGER null(0), local(1), ipv4Address(2), macAddress(3), magicNumber(4), directoryNumber(5)  

TNetworkPolicyID  
the identification number of a network policy.
TEXTUAL-CONVENTION    
  TPolicyID 1..65535 | 65536 | 65537 | 65538  

TItemScope  
This textual convention determines some aspects of an item's behavior regarding creation and use, unused entry garbage collection, and automated promulgation by Element Management System to other systems in the service domain. TItemScope applies to SAP-ingress, SAP-egress, and Network policies, and to IP filters and MAC filters. exclusive: When the scope of an item is defined as exclusive, the item can only be applied once, for example to a single SAP. Attempting to assign the policy to a second SAP is not allowed and will result in an error. If the item is removed from the exclusive SAP, it will become available for assignment to another exclusive SAP. A non-applied exclusive scope policy is a candidate to be removed from the system by a TBD garbage collection command. The system default policies cannot be put into the exclusive scope. An error will be generated if scope exclusive is executed in any policies with a policy-id equal to 1. template: When the scope of an item is defined as template, the item can be applied any number of times. Policies with template scope will not be considered for deletion by a TBD garbage collection command; all items of scope 'template' must be deleted explicitly. The system default policies will always be scope template. An error will occur if a policy-id 1 is attempted to be set to scope exclusive.
TEXTUAL-CONVENTION    
  INTEGER exclusive(1), template(2)  

TItemMatch  
when set to off, the item is not matched. when set to false, packets without the item match the filter. when set to true, packets with the item match the filter.
TEXTUAL-CONVENTION    
  INTEGER off(1), false(2), true(3)  

TPriority  
the priority to apply to a packet
TEXTUAL-CONVENTION    
  INTEGER low(1), high(2)  

TPriorityOrDefault  
the priority to apply to a packet. when set to default(3), the priority from the default action is used.
TEXTUAL-CONVENTION    
  INTEGER low(1), high(2), default(3)  

TPriorityOrUndefined  
the priority to apply to a packet. when set to undefined(0), the priority is not applicable.
TEXTUAL-CONVENTION    
  INTEGER undefined(0), low(1), high(2)  

TProfile  
the profile marking of a packet at the ingress.
TEXTUAL-CONVENTION    
  INTEGER in(1), out(2)  

TProfileOrNone  
Profile marking of a packet.
TEXTUAL-CONVENTION    
  INTEGER none(0), in(1), out(2)  

TDEProfile  
This textual convention specifies the profile marking of a packet. Value of 'in' specifies the in-profile marking. Value of 'out' specifies the out-profile marking. Value of 'de' specifies that the profile marking will be based on the DE (Drop-Eligible) bit. DE bit-value of '0' specifies in-profile and DE bit value of '1' specifies out-profile marking.
TEXTUAL-CONVENTION    
  INTEGER in(1), out(2), de(3)  

TEgressProfile  
The profile marking of a packet. Value of 'in' specifies in-profile marking. Value of 'out' specifies out-profile marking. Value of 'none' specifies the profile marking of the packet will be inherited from the existing enqueuing priority derived from earlier matches in the classification hierarchy.
TEXTUAL-CONVENTION    
  INTEGER in(1), out(2), exceed(4), inplus(5)  

TEgressProfileOrNone  
The profile marking of a packet. Value of 'in' specifies in-profile marking. Value of 'out' specifies out-profile marking. Value of 'de' specifies that the profile marking of the packet will be based on the DE (Drop-Eligible) bit of the packet. DE bit value of '0' specifies in-profile and DE bit value of '1' specifies out-profile marking. Value of 'none' specifies the profile marking of the packet will be inherited from the existing enqueuing priority derived from earlier matches in the classification hierarchy.
TEXTUAL-CONVENTION    
  INTEGER none(0), in(1), out(2), de(3), exceed(4), inplus(5)  

TAdaptationRule  
The adaptation rule to be applied to calculate the operational values for the specified entity.
TEXTUAL-CONVENTION    
  INTEGER max(1), min(2), closest(3)  

TAdaptationRuleOverride  
The adaptation rule to be applied to calculate the operational values for the specified entity.
TEXTUAL-CONVENTION    
  INTEGER noOverride(0), max(1), min(2), closest(3)  

TRemarkType  
The remarking to be used.
TEXTUAL-CONVENTION    
  INTEGER none(1), dscp(2), precedence(3)  

TPrecValue  
The precedence bits as used in the IPv4 header. This constitutes of 3 bits and hence can hold the values from 0 to 7.
TEXTUAL-CONVENTION    
  Integer32 0..7  

TPrecValueOrNone  
The precedence bits as used in the IPv4 header. This constitutes of 3 bits and hence can hold the values from 0 to 7. The value '-1' specifies that the precedence value is undefined/unused.
TEXTUAL-CONVENTION    
  Integer32 -1 | 0..7  

TCpmFilterBurstSize  
The amount of buffer space (in kbytes) assigned to a queue. The value -1 means that the actual value is derived from the corresponding buffer policy's default value.
TEXTUAL-CONVENTION    
  Integer32 -1 | 0..131072  

TBurstSize  
The amount of buffer space (in kbytes) assigned to a queue. The value -1 means that the actual value is derived from the corresponding buffer policy's default value.
TEXTUAL-CONVENTION    
  Integer32 -1 | 0..1048576  

TBurstSizeOverride  
The amount of buffer space (in kbytes) assigned to a queue. The value -1 means that the actual value is derived from the corresponding buffer policy's default value. A value of -2 specifies no override.
TEXTUAL-CONVENTION    
  Integer32 -2 | -1 | 0..1048576  

TBurstSizeBytesOvr  
The amount of buffer space (in bytes) assigned to a queue. The value -1 means that the actual value is derived from the corresponding buffer policy's default value. A value of -2 specifies no override.
TEXTUAL-CONVENTION    
  Integer32 -2 | -1 | 0..1073741824  

TBurstPercent  
The percentage of buffer space assigned to a queue that is reserved for some purpose.
TEXTUAL-CONVENTION    
  Integer32 0..100  

TBurstHundredthsOfPercent  
The percentage of buffer space assigned to a queue that is reserved for some purpose, defined to two decimal places.
TEXTUAL-CONVENTION    
  Integer32 0..10000  

TBurstPercentOrDefault  
The percentage of buffer space assigned to a queue that is reserved for some purpose. The value -1 means that the actual value is derived from the corresponding buffer policy's default value.
TEXTUAL-CONVENTION    
  Integer32 -1 | 0..100  

TBurstPercentOrDefaultOverride  
The percentage of buffer space assigned to a queue that is reserved for some purpose. The value -1 means that the actual value is derived from the corresponding buffer policy's default value. A value of -2 specifies no override.
TEXTUAL-CONVENTION    
  Integer32 -2 | -1 | 0..100  

TRatePercent  
The percentage of maximum rate allowed.
TEXTUAL-CONVENTION    
  Integer32 0..100  

TPIRRatePercent  
The percentage of maximum PIR rate allowed. A value of 0 is not acceptable, so the range begins at 1.
TEXTUAL-CONVENTION    
  Integer32 1..100  

TLevel  
The level of the specified entity while feeding into the parent.
TEXTUAL-CONVENTION    
  Integer32 1..8  

TPortSchedLevel  
The priority level for the specified port scheduler entity.
TEXTUAL-CONVENTION    
  Integer32 1..8  

TLevelOrDefault  
The level of the specified entity while feeding into the parent. The value 0 is used to denote a default value.
TEXTUAL-CONVENTION    
  Integer32 0 | 1..8  

TQueueMode  
The mode in which the queue is operating. If the queue is operating in the 'priority' mode, it is capable of handling traffic differently with two distinct priorities. These priorities are assigned by the stages preceding the queueing framework in the system. When the queue is operating in the 'profile' mode, in other words the color aware mode, the queue tries to provide the appropriate bandwidth to the packets with different profiles. The profiles are assigned according to the configuration of the forwarding class or the sub-forwarding class. In 'priority' mode, the queue does not have the functionality to support the profiled traffic and in such cases the queue will have a degraded performance. However, the converse is not valid and a queue in 'profile' mode should be capable of supporting the different priorities of traffic.
TEXTUAL-CONVENTION    
  INTEGER priority(1), profile(2)  

TQueueStatModeFormat  
The mode in which the queue stats are collected. In 'priority' mode separate stats are collected for high and low priority packets/octets. In 'profile' mode separate stats are collected for in profile and out of profile packets/octets. In 'v4V6' mode separate stats are collected for IPv4 and IPv6 packets/octets
TEXTUAL-CONVENTION    
  INTEGER priority(1), profile(2), v4V6(3)  

TEntryIndicator  
Uniquely identifies an entry in a policy or filter table. The value 0 is not a valid entry-id. When used as insertion point the value 0 indicates that entries must be inserted at the very beginning, i.e.before the first entry defined.
TEXTUAL-CONVENTION    
  Unsigned32 0..65535  

TEntryId  
uniquely identifies an entry in a policy or filter table. to facilitate insertion of entries in the tables, we recommend assigning entry IDs by 10s: 10, 20, 30, etc.
TEXTUAL-CONVENTION    
  TEntryIndicator 1..65535  

TMatchCriteria  
determines whether the entry matches traffic using IP match entries or MAC match entries.
TEXTUAL-CONVENTION    
  INTEGER ip(1), mac(2), none(3)  

TmnxMdaQos  
TmnxMdaQos is an enumerated integer whose value specifies the Quality of Service support of a Media Dependent Adapter (MDA).
TEXTUAL-CONVENTION    
  INTEGER unknown(0), mda(1), hsmda1(2), hsmda2(3), hs(4)  

TAtmTdpDescrType  
The TAtmTdpDescrType is an enumerated integer whose value indicates the types of cell loss priority to be used in conjunction with traffic parameters. The following values are outlined: Integer Value Interpretation ------------- ------------------------ clp0And1pcr PCR applies to CLP 0 and CLP 1 cell flows clp0And1pcrPlusClp0And1scr PCR applies to CLP 0 and CLP 1 cell flows. SCR applies to CLP 0 and CLP 1 cell flows. clp0And1pcrPlusClp0scr PCR applies to CLP 0 and CLP 1 cell flows. SCR applies to CLP 0 cell flows. clp0And1pcrPlusClp0scrTag PCR applies to CLP 0 and CLP 1 cell flows. SCR applies to CLP 0 cell flows.
TEXTUAL-CONVENTION    
  INTEGER clp0And1pcr(0), clp0And1pcrPlusClp0And1scr(1), clp0And1pcrPlusClp0scr(2), clp0And1pcrPlusClp0scrTag(3)  

TDEValue  
This textual convention specifies the DE (Drop Eligible) bit value. The value of '-1' means DE value is not specified.
TEXTUAL-CONVENTION    
  Integer32 -1 | 0..1  

TQGroupType  
This textual convention specifies the type of the Queue-Group.
TEXTUAL-CONVENTION    
  INTEGER port(0), vpls(1)  

TQosOverrideType  
This textual convention specifies the type of the Qos Override.
TEXTUAL-CONVENTION    
  INTEGER queue(1), policer(2), aggRateLimit(3), arbiter(4), scheduler(5), slaAggRateLimit(6), wrrGroup(7)  

TQosOverrideTypeId  
This textual convention indicates the identifier of the queue or policer that is overridden, or zero if the item that is overridden is not a queue or a policer.
TEXTUAL-CONVENTION    
  Integer32 0..63  

TmnxIPsecTunnelTemplateId  
A number used to identify an entry in the tIPsecTnlTempTable.
TEXTUAL-CONVENTION    
  Unsigned32 1..2048  

TmnxIPsecTunnelTemplateIdOrZero  
A number used to identify an entry in the tIPsecTnlTempTable or zero.
TEXTUAL-CONVENTION    
  Unsigned32 0..2048  

TmnxIpSecIsaOperFlags  
The value of TmnxIpSecIsaOperFlags specifies the operational flags that determine the status of the MDAs associated with IPsec ISA.
TEXTUAL-CONVENTION    
  BITS adminDown(0), noActive(1), noResources(2), mcAdminDown(3)  

TmnxIkePolicyAuthMethod  
TmnxIkePolicyAuthMethod data type is an enumerated integer that describes the type of authentication method used.
TEXTUAL-CONVENTION    
  INTEGER psk(1), hybridX509XAuth(2), plainX509XAuth(3), plainPskXAuth(4), cert(5), pskRadius(6), certRadius(7), eap(8), autoEapRadius(9), autoEap(10)  

TmnxIkePolicyAutoEapMethod  
TmnxIkePolicyAutoEapMethod data type is an enumerated integer that describes the type of fallback authentication method use in conjunction with the automatic EAP authentication method.
TEXTUAL-CONVENTION    
  INTEGER psk(1), cert(2), pskOrCert(3)  

TmnxIkePolicyAutoEapOwnMethod  
TmnxIkePolicyAutoEapOwnMethod data type is an enumerated integer that describes the type of fallback authentication method use in conjunction with the automatic EAP authentication method on its own side.
TEXTUAL-CONVENTION    
  INTEGER psk(1), cert(2)  

TmnxIkePolicyOwnAuthMethod  
TmnxIkePolicyOwnAuthMethod data type is an enumerated integer that describes the type of authentication method used for its own side.
TEXTUAL-CONVENTION    
  INTEGER symmetric(0), psk(1), cert(5), eapOnly(8)  

TmnxRsvpDSTEClassType  
TmnxRsvpDSTEClassType is an unsigned integer in the range of (0..7) that defines the class type (CT).
TEXTUAL-CONVENTION    
  Unsigned32 0..7  

TmnxAccPlcyQICounters  
This data type describes a set ingress counters for which accounting data can be collected associated with a given queue.
TEXTUAL-CONVENTION    
  BITS hpo(0), lpo(1), ucp(2), hoo(3), loo(4), uco(5), apo(6), aoo(7), hpd(8), lpd(9), hod(10), lod(11), ipf(12), opf(13), iof(14), oof(15)  

TmnxAccPlcyQECounters  
This data type describes a set egress counters for which accounting data can be collected associated with a given queue.
TEXTUAL-CONVENTION    
  BITS ipf(0), ipd(1), opf(2), opd(3), iof(4), iod(5), oof(6), ood(7)  

TmnxAccPlcyOICounters  
This data type describes a set ingress counters for which accounting data can be collected associated with a given counter.
TEXTUAL-CONVENTION    
  BITS apo(0), aoo(1), hpd(2), lpd(3), hod(4), lod(5), ipf(6), opf(7), iof(8), oof(9)  

TmnxAccPlcyOECounters  
This data type describes a set egress counters for which accounting data can be collected associated with a given counter.
TEXTUAL-CONVENTION    
  BITS ipf(0), ipd(1), opf(2), opd(3), iof(4), iod(5), oof(6), ood(7)  

TmnxAccPlcyAACounters  
This data type describes a set of AA (Application Assurance) counters for which accounting data can be collected. The bits are defined as follows: any (0) - enables reporting when there is a change to any counter sfa (1) - allowed flows from sub nfa (2) - allowed flows to sub sfd (3) - denied flows from sub nfd (4) - denied flows to sub saf (5) - active flows from sub naf (6) - active flows to sub spa (7) - total packets from sub npa (8) - total packets to sub sba (9) - total bytes from sub nba (10) - total bytes to sub spd (11) - total discard packets from sub npd (12) - total discard packets to sub sbd (13) - total discard bytes from sub nbd (14) - total discard bytes to sub sdf (15) - short duration flows mdf (16) - medium duration flows ldf (17) - long duration flows tfd (18) - total flow duration tfc (19) - total flows completed sbm (20) - max throughput in bytes from sub spm (21) - max throughput in packets from sub smt (22) - max throughput timestamp from sub nbm (23) - max throughput in bytes to sub npm (24) - max throughput in packets to sub nmt (25) - max throughput timestamp to sub sfc (26) - forwarding class from sub nfc (27) - forwarding class to sub
TEXTUAL-CONVENTION    
  BITS any(0), sfa(1), nfa(2), sfd(3), nfd(4), saf(5), naf(6), spa(7), npa(8), sba(9), nba(10), spd(11), npd(12), sbd(13), nbd(14), sdf(15), mdf(16), ldf(17), tfd(18), tfc(19), sbm(20), spm(21), smt(22), nbm(23), npm(24), nmt(25), sfc(26), nfc(27)  

TmnxAccPlcyAASubAttributes  
This data type describes a set of AA (Application Assurance) subscriber attributes which must be included in accounting data. The bits are defined as follows: appProfile (0) - application profile appServiceOption (1) - application service option
TEXTUAL-CONVENTION    
  BITS appProfile(0), appServiceOption(1)  

TmnxIsaBbGrpId  
The TmnxIsaBbGrpId data type contains an identification number for an ISA-BB group. An ISA-BB group is a set of MDA of type 'isa-bb' that together performs a particular function such as NAT (Network Address Translation) or IP datagram fragment reassembly. The value zero means that no ISA-BB Group is defined.
TEXTUAL-CONVENTION    
  Unsigned32 0..4  

TmnxVdoGrpIdIndex  
TmnxVdoGrpIdIndex data type describes the id of a TIMETRA-VIDEO-MIB::tmnxVdoGrpEntry and is the primary index for the table.
TEXTUAL-CONVENTION    
  Unsigned32 1..4  

TmnxVdoGrpId  
TmnxVdoGrpId data type describes the identifier for a video group.
TEXTUAL-CONVENTION    
  Unsigned32 0..4  

TmnxVdoGrpIdOrInherit  
The data type describes the identifier for a video group. A value of '-1' indicates that identifier will be inherited from another object that is usually in another mib table.
TEXTUAL-CONVENTION    
  Integer32 -1 | 0..4  

TmnxVdoFccServerMode  
The TmnxVdoFccServerMode data type is an enumerated integer that describes the mode of the Fast Channel Change (FCC) server. A value of 'burst' indicates that the FCC server is enabled and will send the channel at a nominally faster rate than the channel was received based on the TIMETRA-MCAST-PATH-MGMT-MIB::tmnxMcPathVdoPlcyFCCBurst setting. A value of 'dent' indicates that the FCC server will selectively discard frames from the original stream based on the value of TIMETRA-MCAST-PATH-MGMT-MIB::tmnxMcPathVdoPlcyFCCDentThd. A value of 'hybrid' indicates that the FCC server will use combination of 'burst' and 'dent' to send the unicast stream to the client. A value of 'none' indicates that FCC server is disabled.
TEXTUAL-CONVENTION    
  INTEGER none(0), burst(1), dent(2), hybrid(3)  

TmnxVdoPortNumber  
The data type describes the port number of an Internet transport layer protocol.
TEXTUAL-CONVENTION    
  Unsigned32 1024..5999 | 6251..65535  

TmnxVdoIfName  
The data type describes the name of a video interface. The name of a video interface must always start with a letter.
TEXTUAL-CONVENTION    
  TNamedItem  

TmnxTimeInSec  
The data type TmnxTimeInSec describes the Tariff Time for the Charging Data Record (CDR).
TEXTUAL-CONVENTION    
  Unsigned32 0..86400  

TmnxReasContextVal  
The value of the label used to identify the entity using the specified context value on a specific port. 31 0 +--------+--------+--------+--------+ |00000000 00000000 00000000 000XXXXX| +--------+--------+--------+--------+ The value of this object is encoded in the least significant 5 bits and represents the context value.
TEXTUAL-CONVENTION    
  Unsigned32 0..31  

TmnxVdoStatInt  
The data type TmnxVdoStatInt is an enumerated integer that specifies the time duration for which the video statistics are being counted. Setting a variable of this type to 'current' causes the time duration to be set to one second which is the least allowed value. A value of 'interval' makes it necessary for some other MIB object to actually quantify the time interval.
TEXTUAL-CONVENTION    
  INTEGER current(1), interval(2)  

TmnxVdoOutputFormat  
The data type TmnxVdoOutputFormat is an enumerated integer that specifies the output format of the video stream. Setting a variable of this type to 'udp' causes the video stream to be of type 'udp' whereas setting a value of 'rtp-udp' causes the video stream to be of type 'rtp-udp'.
TEXTUAL-CONVENTION    
  INTEGER udp(1), rtp-udp(2)  

TmnxVdoAnalyzerAlarm  
The data type TmnxVdoAnalyzerAlarm is an enumerated integer that specifies the severity of the analyzer state alarm. Setting a variable of this type to 'none' indicates no error level. A value of 'tnc' indicates a TNC (Tech Non-Conformance) error level.A value of 'qos' indicates a QOS (Quality of Service) error level. A value of 'poa' indicates a POA (Program off Air) error level.
TEXTUAL-CONVENTION    
  INTEGER none(0), tnc(1), qos(2), poa(3)  

TmnxVdoAnalyzerAlarmStates  
The data type TmnxVdoAnalyzerAlarmStates is an octet string that represents the analyzer state for the past 10 seconds. Setting a variable of this type to 'good'(00) indicates either there was no alarm during that second or the state of the stream has been cleared from a prior errored state. A value of 'tnc'(01)indicates a TNC (Tech Non-Conformance) error occurred during that second. A value of 'qos'(02) indicates a QOS (Quality of Service) error occurred during that second. A value of 'poa'(03) indicates a POA (Program off Air) error occurred during that second. Since the octet string is 10 bytes long, the 10th byte indicates the most recent state of the stream. Below is how an example stream would appear. Each byte in the stream holds an alarm state for a second. good (00), -- stream was good during 1st second tnc (01), -- stream had tnc error during 2nd second qos (02), -- stream had qos error during 3rd second qos (02), -- stream had qos error during 4th second qos (02), -- stream had qos error during 5th second good (00), -- stream error was cleared during 6th second good (00), -- stream was good during 7th second tnc (01), -- stream had tnc error during 8th second poa (03), -- stream had poa error during 9th second good (00) -- stream error was cleared during 10th second.
TEXTUAL-CONVENTION    
  OCTET STRING Size(10)  

SvcISID  
The SvcISID specifies a 24 bit (0..16777215) service instance identifier for the service. As part of the Provider Backbone Bridging frames, it is used at the destination PE as a demultiplexor field. The value of -1 is used to indicate the value of this object is unspecified.
TEXTUAL-CONVENTION    
  Integer32 -1 | 0..16777215  

TmnxISID  
The TmnxISID specifies a 24 bit (1..16777215) service instance identifier for the service. As part of the Shortest Path Bridging (SPB) frames, it is used at the destination PE as a demultiplexor field. The value of 0 is used to indicate the value of this object is unspecified.
TEXTUAL-CONVENTION    
  Integer32 0 | 1..16777215  

TIngPolicerId  
The data type describes the QoS control policer identifier on ingress side.
TEXTUAL-CONVENTION    
  Integer32 1..32  

TIngPolicerIdOrNone  
The data type describes the QoS control policer identifier on ingress side or zero when not specified.
TEXTUAL-CONVENTION    
  Integer32 0 | 1..32  

TIngressPolicerId  
The data type describes the QoS control policer identifier on ingress side.
TEXTUAL-CONVENTION    
  Integer32 1..63  

TIngressPolicerIdOrNone  
The data type describes the QoS control policer identifier on ingress side or zero when not specified.
TEXTUAL-CONVENTION    
  Integer32 0 | 1..63  

TIngDynPolicerIdOrNone  
The data type describes the QoS dynamic policer identifier on ingress side or zero when not specified.
TEXTUAL-CONVENTION    
  Integer32 0 | 1..63  

TEgrPolicerId  
The data type describes the QoS control policer identifier on egress side.
TEXTUAL-CONVENTION    
  Integer32 1..8  

TEgrPolicerIdOrNone  
The data type describes the QoS control policer identifier on egress side or zero when not specified.
TEXTUAL-CONVENTION    
  Integer32 0 | 1..8  

TEgressPolicerId  
The data type describes the QoS control policer identifier on egress side.
TEXTUAL-CONVENTION    
  Integer32 1..63  

TEgressPolicerIdOrNone  
The data type describes the QoS control policer identifier on egress side or zero when not specified.
TEXTUAL-CONVENTION    
  Integer32 0 | 1..63  

TEgrDynPolicerIdOrNone  
The data type describes the QoS dynamic policer identifier on egress side or zero when not specified.
TEXTUAL-CONVENTION    
  Integer32 0 | 1..63  

TFIRRate  
The static fair rate to be used in kbps. The value -1 means maximum rate.
TEXTUAL-CONVENTION    
  Integer32 -1 | 1..100000000  

TBurstSizeBytes  
The amount of buffer space (in bytes) assigned to a queue. The value -1 means that the actual value is derived from the corresponding buffer policy's default value.
TEXTUAL-CONVENTION    
  Integer32 -1 | 0..1073741824  

THSMDABurstSizeBytes  
The amount of buffer space (in bytes) assigned to a HSMDA queue. The value -1 means that the actual value is derived from the corresponding buffer policy's default value.
TEXTUAL-CONVENTION    
  Integer32 -1 | 0..2688000  

THSMDAQueueBurstLimit  
An explicit shaping burst size of a HSMDA queue. The value -1 means that the actual value is derived from the corresponding queue's default value.
TEXTUAL-CONVENTION    
  Integer32 -1 | 1..1000000  

TClassBurstLimit  
An explicit shaping burst size for a class. The value -1 means that the actual value is derived from the corresponding class's default value.
TEXTUAL-CONVENTION    
  Integer32 -1 | 1..327680  

TPlcrBurstSizeBytes  
The amount of buffer space (in bytes) assigned to a queue by policer. The value -1 means that the actual value is derived from the corresponding buffer policy's default value.
TEXTUAL-CONVENTION    
  Integer32 -1 | 0..16777216  

TBurstSizeBytesOverride  
The amount of buffer space (in bytes) assigned to a queue. The value -1 means that the actual value is derived from the corresponding buffer policy's default value. A value of -2 specifies no override.
TEXTUAL-CONVENTION    
  Integer32 -2 | -1 | 0..134217728  

THSMDABurstSizeBytesOverride  
The amount of buffer space (in bytes) assigned to a HSMDA queue. The value -1 means that the actual value is derived from the corresponding buffer policy's default value. A value of -2 specifies no override.
TEXTUAL-CONVENTION    
  Integer32 -2 | -1 | 0..2688000  

TPlcrBurstSizeBytesOverride  
The amount of buffer space (in bytes) assigned to a queue by policer. The value -1 means that the actual value is derived from the corresponding buffer policy's default value. A value of -2 specifies no override.
TEXTUAL-CONVENTION    
  Integer32 -2 | -1 | 0..16777216  

TmnxBfdSessionProtocols  
This data type indicates what protocols are using a BFD session.
TEXTUAL-CONVENTION    
  BITS ospfv2(0), pim(1), isis(2), staticRoute(3), mcRing(4), rsvp(5), bgp(6), vrrp(7), srrp(8), mcep(9), ldp(10), ipsecTunnel(11), ospfv3(12), mcIpsec(13), mcMobile(14), mplsTp(15), lag(16), opergrp(17), vccv(18), rsvpLsp(19), ldpLsp(20), bgpLsp(21), rip(22), ripng(23)  

TmnxBfdSessOperState  
The TmnxBfdSessOperState data type is an enumerated integer that describes the values used to identify the operational state of a BFD session the instance is relying upon for its fast triggering mechanism.
TEXTUAL-CONVENTION    
  INTEGER unknown(1), connected(2), broken(3), peerDetectsDown(4), notConfigured(5), noResources(6)  

TmnxBfdOnLspSessFecType  
An object of type TmnxBfdOnLspSessFecType indicates the Forwarding Equivalence Class (FEC) type of a Bidirectional Forwarding Detection (BFD) session running on an LSP.
TEXTUAL-CONVENTION    
  INTEGER rsvp(1), ldp(2), bgp(3)  

TmnxIngPolicerStatMode  
TmnxIngPolicerStatMode specifies the mode of statistics collected by this ingress policer.
TEXTUAL-CONVENTION    
  INTEGER noStats(0), minimal(1), offeredProfileNoCIR(2), offeredTotalCIR(3), offeredPriorityNoCIR(4), offeredProfileCIR(5), offeredPriorityCIR(6), offeredLimitedProfileCIR(7), offeredProfileCappedCIR(8), offeredLimitedCappedCIR(9)  

TmnxIngPolicerStatModeOverride  
TmnxIngPolicerStatModeOverride specifies the override mode of statistics collected by this ingress policer.
TEXTUAL-CONVENTION    
  INTEGER noOverride(-1), noStats(0), minimal(1), offeredProfileNoCIR(2), offeredTotalCIR(3), offeredPriorityNoCIR(4), offeredProfileCIR(5), offeredPriorityCIR(6), offeredLimitedProfileCIR(7), offeredProfileCappedCIR(8), offeredLimitedCappedCIR(9)  

TmnxEgrPolicerStatMode  
TmnxEgrPolicerStatMode specifies the mode of statistics collected by this egress policer.
TEXTUAL-CONVENTION    
  INTEGER noStats(0), minimal(1), offeredProfileNoCIR(2), offeredTotalCIR(3), offeredProfileCIR(4), offeredLimitedCappedCIR(5), offeredProfileCappedCIR(6), offeredTotalCirExceed(8), offeredFourProfileNoCir(9), offeredTotalCirFourProfile(10)  

TmnxEgrPolicerStatModeOverride  
TmnxEgrPolicerStatModeOverride specifies the override mode of statistics collected by this egress policer.
TEXTUAL-CONVENTION    
  INTEGER noOverride(-1), noStats(0), minimal(1), offeredProfileNoCIR(2), offeredTotalCIR(3), offeredProfileCIR(4), offeredLimitedCappedCIR(5), offeredProfileCappedCIR(6), offeredTotalCirExceed(8), offeredFourProfileNoCir(9), offeredTotalCirFourProfile(10)  

TmnxTlsGroupId  
A number used to identify a TLS Group. This ID must be unique within that Service Domain.
TEXTUAL-CONVENTION    
  Unsigned32 1..4094  

TSubHostId  
A number used to uniquely identify a subscriber host in the system
TEXTUAL-CONVENTION    
  Unsigned32  

TDirection  
TDirection denotes a direction.
TEXTUAL-CONVENTION    
  INTEGER both(0), ingress(1), egress(2)  

TDirectionIngEgr  
TDirectionIngEgr denotes a direction.
TEXTUAL-CONVENTION    
  INTEGER ingress(1), egress(2)  

TBurstLimit  
An explicit shaping burst size for a queue. The value of -1 specifies system default value.
TEXTUAL-CONVENTION    
  Integer32 -1 | 1..14000000  

TMacFilterType  
A type containing the possible types of MAC filters provided by the system
TEXTUAL-CONVENTION    
  INTEGER normal(1), isid(2), vid(3)  

TIPFilterType  
A type containing the possible types of IP/IPv6 filters provided by the system.
TEXTUAL-CONVENTION    
  INTEGER normal(1), vxlanVni(2)  

TmnxPwGlobalId  
A number used to identify a global pseudo-wire routing identifier.
TEXTUAL-CONVENTION    
  Unsigned32 1..4294967295  

TmnxPwGlobalIdOrZero  
A number used to identify a global pseudo-wire routing identifier or zero.
TEXTUAL-CONVENTION    
  Unsigned32  

TmnxPwPathHopId  
A number used to identify a specific hop associated with pseudo-wire routing path.
TEXTUAL-CONVENTION    
  Unsigned32 1..16  

TmnxPwPathHopIdOrZero  
A number used to identify a specific hop associated with pseudo-wire routing path.
TEXTUAL-CONVENTION    
  Unsigned32 0..16  

TmnxSpokeSdpId  
A number used to identify a multi-segment pseudo-wire provider-edge identifier.
TEXTUAL-CONVENTION    
  Unsigned32 1..4294967295  

TmnxSpokeSdpIdOrZero  
A number used to identify a multi-segment pseudo-wire provider-edge identifier.
TEXTUAL-CONVENTION    
  Unsigned32  

TmnxMsPwPeSignaling  
A number used to identify a multi-segment pseudo-wire provider-edge signaling type.
TEXTUAL-CONVENTION    
  INTEGER auto(1), master(2)  

TmnxLdpFECType  
TmnxLdpFECType determines the kind of FEC that the label mapping, withdraw, release and request messages are referring to.
TEXTUAL-CONVENTION    
  INTEGER addrWildcard(1), addrPrefix(2), addrHost(3), vll(128), vpws(129), vpls(130)  

TmnxSvcOperGrpCreationOrigin  
A number used to identify creation origin for the service operational group.
TEXTUAL-CONVENTION    
  INTEGER manual(1), mvrp(2)  

TmnxOperGrpHoldUpTime  
TmnxOperGrpHoldUpTime indicates time-interval in seconds for the service operational-group hold uptime.
TEXTUAL-CONVENTION    
  Unsigned32 0..3600  

TmnxOperGrpHoldDownTime  
TmnxOperGrpHoldDownTime indicates time-interval in seconds for the service operational-group hold down time.
TEXTUAL-CONVENTION    
  Unsigned32 0..3600  

TmnxSrrpPriorityStep  
TmnxSrrpPriorityStep indicates the range of the priority steps used by the operational group to monitor SRRP.
TEXTUAL-CONVENTION    
  Integer32 0..10  

TmnxAiiType  
TmnxAiiType indicates LDP FEC 129 Attachment Individual Identifier (AII) type.
TEXTUAL-CONVENTION    
  INTEGER aiiType1(1), aiiType2(2)  

TmnxSpbFid  
TmnxSpbFid indicates Shortest Path Bridging forwarding database identifier.
TEXTUAL-CONVENTION    
  Integer32 1..4095  

TmnxSpbFidOrZero  
TmnxSpbFid indicates Shortest Path Bridging forwarding database identifier.
TEXTUAL-CONVENTION    
  Integer32 0..4095  

TmnxSpbBridgePriority  
TmnxSpbFid indicates the bridge priority for Shortest Path Bridging.
TEXTUAL-CONVENTION    
  Integer32 0..15  

TmnxSlopeMap  
TmnxSlopeMap indicates the mapping style of the slope.
TEXTUAL-CONVENTION    
  INTEGER none(0), low(1), high(2), highLow(3)  

TmnxCdrType  
The TmnxCdrType is an enumerated integer that describes the current charging type in Charging Data Record (CDR). pgwCdr - indicates Packet data network Gateway CDR gCdr - indicates Gateway GPRS Support Node (GGSN) CDR, where GPRS stands for General Packet Radio Service. eGCdr - indicates Enhanced Gateway GPRS Support Node (GGSN) CDR.
TEXTUAL-CONVENTION    
  INTEGER pgwCdr(1), gCdr(2), eGCdr(3)  

TmnxThresholdGroupType  
The TmnxThresholdGroupType is an enumerated integer that describes the group type in threshold based monitoring. brMgmtLimit - indicates the group for bearer management limit brMgmtCfSuccess - indicates the group for bearer management call flow success brMgmtCfFailure - indicates the group for bearer management call flow failure brMgmtTraffic - indicates the group for bearer management traffic pathMgmt - indicates the group for path management mgIsmSystem - indicates the group for the system of mobile gateway integrated service module pdnConnections - indicates the group for the Packet Data Network (PDN) connections.
TEXTUAL-CONVENTION    
  INTEGER brMgmtLimit(1), brMgmtCfSuccess(2), brMgmtCfFailure(3), brMgmtTraffic(4), pathMgmt(5), pdnConnections(6), mgIsmSystem(7)  

TmnxVpnIpBackupFamily  
The value of TmnxVpnIpBackupFamily specifies the respective vpn family for which backup paths would be enabled.
TEXTUAL-CONVENTION    
  BITS ipv4(0), ipv6(1)  

TmnxTunnelGroupId  
The value of TmnxTunnelGroupId specifies the tunnel-group identifier.
TEXTUAL-CONVENTION    
  Unsigned32 1..16  

TmnxTunnelGroupIdOrZero  
The value of TmnxTunnelGroupId specifies the tunnel-group identifier including zero indicating that group-id is not specified.
TEXTUAL-CONVENTION    
  Unsigned32 0..16  

TmnxQosBytesHex  
Represents the QoS bytes that has been requested for the bearer context of an User Equipment (UE).
TEXTUAL-CONVENTION    
  OCTET STRING Size(0..30)  

TSiteOperStatus  
TSiteOperStatus data type is an enumerated integer that describes the values used to identify the current operational state of a site.
TEXTUAL-CONVENTION    
  INTEGER up(1), down(2), outOfResource(3)  

TmnxSpbFdbLocale  
TmnxSpbFdbLocale data type is an enumerated integer that describes the values used to indicate source of forwarding database (FDB) entry for Shortest Path Bridging (SPB).
TEXTUAL-CONVENTION    
  INTEGER local(1), sap(2), sdp(3), unknown(4)  

TmnxSpbFdbState  
TmnxSpbFdbState data type is an enumerated integer that describes the values used to indicate state of the forwarding database FDB entry for Shortest Path Bridging (SPB).
TEXTUAL-CONVENTION    
  INTEGER ok(0), addModPending(1), delPending(2), sysFdbLimit(3), noFateShared(4), svcFdbLimit(5), noUcast(6)  

TmnxCdrDiagnosticAction  
The TmnxCdrDiagnosticAction is an enumerated integer that describes whether the Diagnostics should be included or excluded in the Charging Data Record (CDR).
TEXTUAL-CONVENTION    
  INTEGER included(1), excluded(2)  

TmnxLinkMapProfileId  
The data type TmnxLinkMapProfileId describes the link map profile identifier.
TEXTUAL-CONVENTION    
  Integer32 1..64  

TmnxLinkMapProfileIdOrZero  
The data type TmnxLinkMapProfileId describes the link map profile identifier or zero.
TEXTUAL-CONVENTION    
  Integer32 0 | 1..64  

TmnxDayOfWeek  
The TmnxDayOfWeek is an enumerated integer that describes the day of the week.
TEXTUAL-CONVENTION    
  INTEGER unspecified(0), sunday(1), monday(2), tuesday(3), wednesday(4), thursday(5), friday(6), saturday(7)  

TmnxDayOfWeekList  
The TmnxDayOfWeekList describes days of the week in a bitset format.
TEXTUAL-CONVENTION    
  BITS sunday(0), monday(1), tuesday(2), wednesday(3), thursday(4), friday(5), saturday(6)  

TmnxMplsTpGlobalID  
The value of TmnxMplsTpGlobalID specifies the MPLS-TP global identifier.
TEXTUAL-CONVENTION    
  Unsigned32  

TmnxMplsTpNodeID  
The value of TmnxMplsTpNodeID specifies the MPLS-TP node identifier.
TEXTUAL-CONVENTION    
  Unsigned32  

TmnxMplsTpTunnelType  
The type of this MPLS-TP tunnel entity.
TEXTUAL-CONVENTION    
  INTEGER mplsTpStatic(1)  

TmnxDistCpuProtPacketRateLimit  
A packet rate limit expressed in packets per second for Distributed CPU Protection Policy parameters. The value -1 means max rate.
TEXTUAL-CONVENTION    
  Integer32 -1 | 0..255  

TmnxDistCpuProtRate  
A kbps limiting rate in kilobits-per-second for Distributed CPU Protection Policy parameters. The value -1 means max rate.
TEXTUAL-CONVENTION    
  Integer32 -1 | 1..20000000  

TmnxDistCpuProtBurstSize  
The amount of buffer space (in kilobytes) assigned to a queue by policer for Distributed CPU Protection Policy parameters.
TEXTUAL-CONVENTION    
  Integer32 -1 | 0..4194304  

TmnxDistCpuProtActionDuration  
An exceed action rate in seconds for Distributed CPU Protection Policy parameters determining hold-down duration for specified exceed-action. The value of 0 means no hold-down and value of -1 means indefinite hold-down duration.
TEXTUAL-CONVENTION    
  Integer32 -1 | 0 | 1..10080  

TmnxDistCpuProtAction  
The TmnxDistCpuProtAction data type is an enumerated integer that describes the values used to specify the action to be taken on the traffic when the filter entry matches. discard (1) packets matching the filter entry are discarded low-priority (2) packets matching the filter entry are marked as low-priority none (3) no action is taken.
TEXTUAL-CONVENTION    
  INTEGER discard(1), low-priority(2), none(3)  

TmnxDistCpuProtEnforceType  
The TmnxDistCpuProtEnforceType data type is an enumerated integer that describes the values used to specify the enforcement type.
TEXTUAL-CONVENTION    
  INTEGER static(1), dynamic(2)  

TmnxDistCpuProtProtocolId  
The TmnxDistCpuProtProtocolId data type is an enumerated integer that indicates the protocols supported for the Distributed CPU Protection Policy.
TEXTUAL-CONVENTION    
  INTEGER arp(1), dhcp(2), http-redirect(3), icmp(4), igmp(5), mld(6), ndis(7), pppoe-pppoa(8), all-unspecified(9), mpls-ttl(10), bfd-cpm(11), bgp(12), eth-cfm(13), isis(14), ldp(15), ospf(16), pim(17), rsvp(18)  

TmnxDistCpuProtRateType  
The TmnxDistCpuProtRateType data type is an enumerated integer that describes the rate type being applied by the policer for the Distributed CPU Protection Policy.
TEXTUAL-CONVENTION    
  INTEGER packets(1), kbps(2)  

TmnxDistCpuProtLogEventType  
The TmnxDistCpuProtLogEventType data type is an enumerated integer that describes the state of log events for Distributed CPU Protection Policy. none (0) indicates log events is disabled enable (1) indicates log events is enabled verbose (2) indicates generation of additional log events to be used for debug/tuning/investigations which would have not been generated when TmnxDistCpuProtLogEventType is set to 'enable'.
TEXTUAL-CONVENTION    
  INTEGER none(0), enable(1), verbose(2)  

TmnxDistCpuProtState  
The TmnxDistCpuProtState data type is an enumerated integer that describes the state of the policer for the Distributed CPU Protection Policy.
TEXTUAL-CONVENTION    
  INTEGER exceed(1), conform(2), not-applicable(3)  

TmnxIsidMFibStatus  
The TmnxIsidMFibStatus data type describes the MFIB status of the ISID.
TEXTUAL-CONVENTION    
  BITS ok(0), addPending(1), delPending(2), sysMFibLimit(3), useDefMCTree(4)  

TmnxBfdIntfSessOperState  
The TmnxBfdIntfSessOperState data type is an enumerated integer that describes the values used to identify the operational state of a BFD session is relying upon for its fast triggering mechanism.
TEXTUAL-CONVENTION    
  INTEGER unknown(1), connected(2), broken(3), peerDetectsDown(4), notConfigured(5), noResources(6)  

TmnxBfdEncap  
The TmnxBfdEncap data type is an enumerated integer indicating encapsulation used for in the BFD operation.
TEXTUAL-CONVENTION    
  INTEGER ipv4(1)  

TLDisplayString  
The TLDisplayString is DisplayString of 1022 characters. Any object defined using this syntax may not exceed 1022 characters in length.
TEXTUAL-CONVENTION    
  OCTET STRING Size(0..1022)  

IPv6FlowLabel  
The flow identifier or Flow Label in an IPv6 packet header that may be used to discriminate traffic flows. (RFC3595). The value -1 indicates 'no flowLabel'
TEXTUAL-CONVENTION    
  Integer32 -1 | 0..1048575  

IPv6FlowLabelMask  
IPv6 flow label mask
TEXTUAL-CONVENTION    
  Unsigned32 0..1048575  

TmnxWlanGwIsaGrpId  
The TmnxWlanGwIsaGrpId data type contains an identification number for a Wireless Local Access Network Gateway Integrated Service Adaptor group.
TEXTUAL-CONVENTION    
  Unsigned32 1..4  

TmnxWlanGwIsaGrpIdOrZero  
The TmnxWlanGwIsaGrpIdOrZero data type contains an identification number for a Wireless Local Access Network Gateway Integrated Service Adaptor (ISA) group. The value zero means that no WLAN Gateway ISA Group is defined.
TEXTUAL-CONVENTION    
  Unsigned32 0..4  

TmnxMplsLdpNgIdType  
A value that represents the type of LDP identifier ipv4(1) An IPv4 identifier type as defined by the InetAddressIPv4 textual convention. ipv6(2) An IPv6 identifier type as defined by the InetAddressIPv6 textual convention. Each definition of a concrete TmnxMplsLdpNgIdType value must be accompanied by a definition of a textual convention for use with that TmnxMplsLdpNgIdType. Implementations must ensure that TmnxMplsLdpNgIdType objects and any dependent objects (e.g., TmnxMplsLdpNgIdentifier objects) are consistent. An inconsistentValue error must be generated if an attempt to change an TmnxMplsLdpNgIdType object would, for example, lead to an undefined TmnxMplsLdpNgIdentifier value. In particular, TmnxMplsLdpNgIdType/TmnxMplsLdpNgIdentifier pairs must be changed together if the identifier type changes (e.g., from ipv6(2) to ipv4(1)).
TEXTUAL-CONVENTION    
  INTEGER ipv4(1), ipv6(2)  

TmnxMplsLdpNgIdentifier  
The LDP identifier is a eighteen octet quantity which is used to identify a Label Switch Router (LSR) label space. When the LDP Id type is 'ipv4', the first four octets encode an IP address assigned to the LSR, and next two octets identify a specific label space within the LSR assigned to the LSR. When the LDP Id type is 'ipv6', the first sixteen octets encode an IP address an assigned to the LSR, and last two octets identify a specific label space within the LSR.
TEXTUAL-CONVENTION    
  OCTET STRING Size(0..18)  

TmnxMplsLsrNgIdentifier  
The Label Switch Router (LSR) identifier is the first 16 bytes or the Router Id component of the IPv6 Label Distribution Protocol (LDP) identifier.
TEXTUAL-CONVENTION    
  OCTET STRING Size(16)  

TmnxLagPerLinkHashClass  
The TmnxLagPerLinkHashClass is the class of traffic which along with the relative weight is used in the egress hashing on the LAG.
TEXTUAL-CONVENTION    
  Integer32 1..3  

TmnxLagPerLinkHashClassOrNone  
The TmnxLagPerLinkHashClass is the class of traffic which along with the relative weight is used in the egress hashing on the LAG.
TEXTUAL-CONVENTION    
  Integer32 0..3  

TmnxLagPerLinkHashWeight  
The TmnxLagPerLinkHashWeight is the relative weight of the traffic which along with the class is used in the egress hashing on the LAG.
TEXTUAL-CONVENTION    
  Integer32 1..1024  

BgpConnectRetryTime  
The value of BgpConnectRetryTime is a time interval in seconds for a 'ConnectRetry' timer.default is 120 seconds.
TEXTUAL-CONVENTION    
  Integer32 1..65535  

BgpHoldTime  
The value of BgpHoldTime is a time interval in seconds for Hold Timer.
TEXTUAL-CONVENTION    
  Integer32 0 | 3..65535  

TmnxInternalSchedWeightMode  
The value of TmnxInternalSchedWeightMode specifies the weight-mode applied to queues using internal-scheduler. Various modes can be enumerated as follows: noOverride (1) - follows queue behavior specified at the card level. default (2) - queues are equally weighted except for mixed-speed LAG (when the value of TIMETRA-LAG-MIB.mib::tLagPerFpIngQueuing is set to 'false (2)') where queues are weighted based on port-speed. forceEqual (3) - all queues are always equally weighted. offeredLoad (4) - queues are weighted based on offered load. cappedOfferedLoad (5) - queues are weighted based on offered load capped by admin PIR.
TEXTUAL-CONVENTION    
  INTEGER noOverride(1), default(2), forceEqual(3), offeredLoad(4), cappedOfferedLoad(5)  

TmnxHigh32  
The upper 32 bits of a 64 bit value.
TEXTUAL-CONVENTION    
  Unsigned32  

TmnxLow32  
The lower 32 bits of a 64 bit value.
TEXTUAL-CONVENTION    
  Unsigned32  

TQosQueuePIRRate  
The PIR rate to be used in kbps. The value -1 means maximum rate.
TEXTUAL-CONVENTION    
  Integer32 -1 | 1..2000000000  

TQosQueueCIRRate  
The CIR rate to be used in kbps. The value -1 means maximum rate.
TEXTUAL-CONVENTION    
  Integer32 -1 | 0..2000000000  

TQosQueuePIRRateOverride  
The PIR rate to be used in kbps. The value -1 means maximum rate. A value of -2 specifies no override.
TEXTUAL-CONVENTION    
  Integer32 -2 | -1 | 1..2000000000  

TQosQueueCIRRateOverride  
The CIR rate to be used in kbps. The value -1 means maximum rate. A value of -2 specifies no override.
TEXTUAL-CONVENTION    
  Integer32 -2 | -1 | 0..2000000000  

TResolveStatus  
The TResolveStatus indicates resolution status of the tunnels.
TEXTUAL-CONVENTION    
  INTEGER disabled(0), filter(1), any(2), match-family-ip(3)  

LAGInterfaceNumber  
The unique number identifying a LAG interface. There are maximum 64 LAG interfaces, when the value of TIMETRA-CHASSIS-MIB::tmnxChassisType is '5' (ESS-1/SR-1).
TEXTUAL-CONVENTION    
  Integer32 1..800  

LAGInterfaceNumberOrZero  
LAGInterfaceNumberOrZero is similar to LAGInterfaceNumber but includes zero indicating invalid LAG identifier.
TEXTUAL-CONVENTION    
  Integer32 0 | 1..800  

TmnxRouteTargetOrigin  
TmnxRouteTargetOrigin indicates the origin of the route-target policy.
TEXTUAL-CONVENTION    
  INTEGER none(0), configured(1), derivedVpls(2), derivedEvi(3), vsi(4)  

TmnxRouteDistType  
TmnxRouteDistType indicates the type of the route-distinguisher.
TEXTUAL-CONVENTION    
  INTEGER none(0), configured(1), derivedVpls(2), derivedEvi(3), auto(4), default(5)  

TmnxScriptAuthType  
The tmnxCliScriptAuthUserType datatype is an enumerated integer that indicates the type of module executing a CLI command script.
TEXTUAL-CONVENTION    
  INTEGER none(0), cron(1), xmpp(2), event-script(3), vsd(4)  

TmnxISIDNoZero  
The TmnxISID specifies a 24 bit (1..16777215) service instance identifier for the service. As part of the Shortest Path Bridging (SPB) frames, it is used at the destination PE as a demultiplexor field.
TEXTUAL-CONVENTION    
  Integer32 1..16777215  

TmnxSvcEvi  
The TmnxSvcEvi specifies an ethernet EVPN identifier value.
TEXTUAL-CONVENTION    
  Integer32 1..65535  

TmnxSvcEviOrZero  
The TmnxSvcEviOrZero specifies an ethernet EVPN identifier value. Zero indicates no such value specified.
TEXTUAL-CONVENTION    
  Integer32 0..65535  

TmnxSubTerminationType  
The TmnxSubTerminationType indicates how the subscriber host or session is terminated.
TEXTUAL-CONVENTION    
  INTEGER local(1), localWholesale(2), localRetail(3)  

TmnxLongDisplayString  
The TmnxLongDisplayString indicates a long DisplayString.
TEXTUAL-CONVENTION    
  OCTET STRING Size(0..1024)  

TmnxLongDisplayStringToBinary  
The TmnxLongDisplayString indicates a long DisplayString.
TEXTUAL-CONVENTION    
  TmnxLongDisplayString  

TmnxLongDisplayStringLegacyBinary  
The TmnxLongDisplayString indicates a long DisplayString.
TEXTUAL-CONVENTION    
  OCTET STRING Size(0..900)  

TmnxProxyEntryType  
The TmnxProxyEntryType indicates type of proxy ARP or ND entry.
TEXTUAL-CONVENTION    
  INTEGER evpn(1), stat(2), dyn(3), dup(4)  

TmnxCBFClasses  
The TmnxCBFClasses indicates a set of forwarding classes.
TEXTUAL-CONVENTION    
  BITS be(0), l2(1), af(2), l1(3), h2(4), ef(5), h1(6), nc(7), defaultLsp(8)  

TmnxUserPassword  
The value of TmnxUserPassword indicates a password as a plaintext string, or as a bcrypt encrypted hash. The value of TmnxUserPassword cannot be more than 56 characters if it is a plaintext string. Any GET request on this type of object returns an empty string.
TEXTUAL-CONVENTION    
  DisplayString Size(0..60)  

TmnxUdpPort  
The value of TmnxUdpPort is the port used to send messages to an event collector target. 514 is the IANA assigned port number for syslog. 162 is the IANA assigned port number for SNMP notifications.
TEXTUAL-CONVENTION    
  Integer32 0..65535  

TmnxUuid  
The value of TmnxUuid specifies the Universally Unique Identifier (UUID). The UUID consists of 32 hexadecimal digits.
TEXTUAL-CONVENTION    
  OCTET STRING Size(16)  

TmnxSyslogFacility  
The value of TmnxSyslogFacility is an enumerated integer that specifies which syslog facility is the intended destination for the log event stream.
TEXTUAL-CONVENTION    
  INTEGER kernel(0), user(1), mail(2), systemd(3), auth(4), syslogd(5), printer(6), netnews(7), uucp(8), cron(9), authpriv(10), ftp(11), ntp(12), logaudit(13), logalert(14), cron2(15), local0(16), local1(17), local2(18), local3(19), local4(20), local5(21), local6(22), local7(23)  

TmnxSyslogSeverity  
The value of TmnxSyslogSeverity is an enumerated integer that specifies the severity levels of syslog messages.
TEXTUAL-CONVENTION    
  INTEGER emergency(0), alert(1), critical(2), error(3), warning(4), notice(5), info(6), debug(7)  

TmnxEvpnMultiHomingState  
The value of TmnxEvpnMultiHomingState indicates multi-homing state of the element.
TEXTUAL-CONVENTION    
  INTEGER disabled(0), singleActive(1), singleActiveNoEsiLabel(2), allActive(3)  

TmnxBgpEvpnAcEthTag  
The TmnxBgpEvpnAcEthTag indicates ethernet tag value of the BGP EVPN attachment circuit.
TEXTUAL-CONVENTION    
  Integer32 0..16777215  

TmnxL2tpTunnelGroupName  
The TmnxL2tpTunnelGroupName data type contains a valid string to identify a Layer Two Tunneling Protocol Tunnel Group.
TEXTUAL-CONVENTION    
  DisplayString Size(1..63)  

TmnxL2tpTunnelGroupNameOrEmpty  
The TmnxL2tpTunnelGroupNameOrEmpty data type contains a valid string to identify a Layer Two Tunneling Protocol Tunnel Group. An empty string indicates that no Tunnel Group is defined.
TEXTUAL-CONVENTION    
  DisplayString Size(0..63)  

TFilterID  
The identification number of a filter. 0 indicates an invalid filter-id.
TEXTUAL-CONVENTION    
  Unsigned32 0..65535  

TIPFilterID  
The identification number of an IP filter.
TEXTUAL-CONVENTION    
  TFilterID  

TDHCPFilterID  
The identification number of a DHCP filter.
TEXTUAL-CONVENTION    
  TFilterID  

TEntryIdOrZero  
uniquely identifies an entry in a policy or filter table. to facilitate insertion of entries in the tables, we recommend assigning entry IDs by 10s: 10, 20, 30, etc. The value 0, means that the object does not refer to a filter entry at this time.
TEXTUAL-CONVENTION    
  TEntryIndicator 0..65535  

MciBoolean  
This provides MCI type to for the objects which do not have well defined defaults
TEXTUAL-CONVENTION    
  INTEGER mciTrue(1), mciFalse(2)  

TmnxPppCpState  
The TmnxPppCpState data type is an enumerated integer that describes the current status of a PPP link. It can be applied to both LCP and NCP links.
TEXTUAL-CONVENTION    
  INTEGER initial(1), starting(2), closed(3), stopped(4), closing(5), stopping(6), requestSent(7), ackReceived(8), ackSent(9), opened(10)  

TmnxRipNgAuthType  
The TmnxRipNgAuthType TC defines the authentication method to be used for RIP/RIP-NG. Allowed values are : noAuthentication(1) - No authentication method simplePassword(2) - Simple password based authentication md5(3) - 16 byte MD5 Authentication md20(4) - 20 byte MD5 Authentication.
TEXTUAL-CONVENTION    
  INTEGER noAuthentication(1), simplePassword(2), md5(3), md20(4)  

TmnxRipNgAuthKey  
The TmnxRipNgAuthKey TC defines the authentication key to be used when the authentication type has been configured to either simplePassword(2), md5(3) or md20(4) (RIP_AUTH_EXTENSION) {or md16(5) or md5-20(6) }(see TmnxRipNgAuthType).
TEXTUAL-CONVENTION    
  OCTET STRING Size(0..16)  

TmnxAddressAndPrefixType  
Tok_String
TEXTUAL-CONVENTION    
  InetAddressType  

TmnxAddressAndPrefixAddress  
Tok_String
TEXTUAL-CONVENTION    
  InetAddress  

TmnxAddressAndPrefixPrefix  
Tok_String
TEXTUAL-CONVENTION    
  InetAddressPrefixLength  

TmnxIpv6AddressAndPrefixAddress  
Tok_String
TEXTUAL-CONVENTION    
  InetAddressIPv6  

TmnxIpv6AddressAndPrefixPrefix  
Tok_String
TEXTUAL-CONVENTION    
  InetAddressPrefixLength  

TmnxIpv4AddressAndMaskOrPrefixAddress  
Tok_String
TEXTUAL-CONVENTION    
  IpAddress  

TmnxIpv4AddressAndMaskOrPrefixMask  
Tok_String
TEXTUAL-CONVENTION    
  IpAddress  

TmnxIpv4AddressAndMaskOrPrefixPrefix  
Tok_String
TEXTUAL-CONVENTION    
  IpAddressPrefixLength  

TmnxIpv4AddressAndPrefixAddress  
Tok_String
TEXTUAL-CONVENTION    
  IpAddress  

TmnxIpv4AddressAndPrefixPrefix  
Tok_String
TEXTUAL-CONVENTION    
  IpAddressPrefixLength  

TmnxIpv6AddressAndMaskOrPrefixAddress  
Tok_String
TEXTUAL-CONVENTION    
  InetAddressIPv6  

TmnxIpv6AddressAndMaskOrPrefixMask  
Tok_String
TEXTUAL-CONVENTION    
  InetAddressIPv6  

TmnxIpv6AddressAndMaskOrPrefixPrefix  
Tok_String
TEXTUAL-CONVENTION    
  InetAddressPrefixLength  

TmnxAddressAndMaskOrPrefixType  
Tok_String
TEXTUAL-CONVENTION    
  InetAddressType  

TmnxAddressAndMaskOrPrefixAddress  
Tok_String
TEXTUAL-CONVENTION    
  InetAddress  

TmnxAddressAndMaskOrPrefixPrefix  
Tok_String
TEXTUAL-CONVENTION    
  InetAddressPrefixLength  

TmnxAddressAndMaskOrPrefixMask  
Tok_String
TEXTUAL-CONVENTION    
  InetAddress  

TmnxAddressWithZoneType  
Tok_String
TEXTUAL-CONVENTION    
  InetAddressType  

TmnxAddressWithZoneAddress  
Tok_String
TEXTUAL-CONVENTION    
  InetAddress  

THsPirRate  
The HS PIR rate to be used in Mbps. The value of 4294967295(0xFFFFFFFF) means maximum rate.
TEXTUAL-CONVENTION    
  Unsigned32 1..100000 | 4294967295  

THsPirRateOverride  
The HS PIR rate to be used in Mbps. The value of 4294967295(0xFFFFFFFF) means maximum rate. The value of 4294967294(0xFFFFFFFE) means no override.
TEXTUAL-CONVENTION    
  Unsigned32 1..100000 | 4294967294 | 4294967295  

THsSchedulerPolicyGroupId  
The value of THsSchedulerPolicyGroupId specifies the identification number of a HS scheduler policy group. A value of zero (0) indicates that no specific group identification has been assigned for this object. When an object of type THsSchedulerPolicyGroupId is an SNMP table index, an index value of zero (0) is not allowed and a noCreation error will be returned.
TEXTUAL-CONVENTION    
  Integer32 0 | 1  

THsSchedulerPolicyWeight  
The weight of the specified HS entity while feeding into the parent.
TEXTUAL-CONVENTION    
  Integer32 1..127  

THsSchedulerPolicyWeightOverride  
The weight of the specified HS entity while feeding into the parent. A value of -2 specifies no override.
TEXTUAL-CONVENTION    
  Integer32 -2 | 1..127  

TmnxWaveKey  
The value of TmnxWaveKey specifies the Wavelength to be transmitted on the interface's optical signal. The following table describes the possible values based on ITU channel. Key1 and Key2 must match in modulo 2 with each other. Index ITU Key 1 Key 2 channel First Last First Last ------------------------------------------- 0 61 1548 1548 2032 2032 // 1696 Test Channel // Original Tropic Channels (index 1 to 32) 1 59 1 15 545 559 2 58 18 32 562 576 3 57 35 49 579 593 4 56 52 66 596 610 5 54 69 83 613 627 6 53 86 100 630 644 7 52 103 117 647 661 8 51 120 134 664 678 9 49 137 151 681 695 10 48 154 168 698 712 11 47 171 185 715 729 12 46 188 202 732 746 13 44 205 219 749 763 14 43 222 236 766 780 15 42 239 253 783 797 16 41 256 270 800 814 17 39 273 287 817 831 18 38 290 304 834 848 19 37 307 321 851 865 20 36 324 338 868 882 21 34 341 355 885 899 22 33 358 372 902 916 23 32 375 389 919 933 24 31 392 406 936 950 25 29 409 423 953 967 26 28 426 440 970 984 27 27 443 457 987 1001 28 26 460 474 1004 1018 29 24 477 491 1021 1035 30 23 494 508 1038 1052 31 22 511 525 1055 1069 32 21 528 542 1072 1086 // 1696 Extension 42 channels (index 33 to 42) 33 60 1089 1103 1573 1587 34 55 1106 1120 1590 1604 35 50 1123 1137 1607 1621 36 45 1140 1154 1624 1638 37 40 1157 1171 1641 1655 38 35 1174 1188 1658 1672 39 30 1191 1205 1675 1689 40 25 1208 1222 1692 1706 41 20 1225 1239 1709 1723 42 19 1242 1256 1726 1740 // 1830 Extension to 44 channels (index 43 and 44) 43 18 1259 1273 1743 1757 44 17 1276 1290 1760 1774 // 1830 Extension to 88 channels (index 45 to 88) 45 595 1293 1307 1777 1791 46 585 1310 1324 1794 1808 47 575 1327 1341 1811 1825 48 565 1344 1358 1828 1842 49 545 1361 1375 1845 1859 50 535 1378 1392 1862 1876 51 525 1395 1409 1879 1893 52 515 1412 1426 1896 1910 53 495 1429 1443 1913 1927 54 485 1446 1460 1930 1944 55 475 1463 1477 1947 1961 56 465 1480 1494 1964 1978 57 445 1497 1511 1981 1995 58 435 1514 1528 1998 2012 59 425 1531 1545 2015 2029 60 415 1548 1562 2032 2046 61 395 3585 3599 2049 2063 62 385 3602 3616 2066 2080 63 375 3619 3633 2083 2097 64 365 3636 3650 2100 2114 65 345 3653 3667 2117 2131 66 335 3670 3684 2134 2148 67 325 3687 3701 2151 2165 68 315 3704 3718 2168 2182 69 295 3721 3735 2185 2199 70 285 3738 3752 2202 2216 71 275 3755 3769 2219 2233 72 265 3772 3786 2236 2250 73 245 3789 3803 2253 2267 74 235 3806 3820 2270 2284 75 225 3823 3837 2287 2301 76 215 3840 3854 2304 2318 77 605 3857 3871 2321 2335 78 555 3874 3888 2338 2352 79 505 3891 3905 2355 2369 80 455 3908 3922 2372 2386 81 405 3434 3448 3946 3960 82 355 3451 3465 3963 3977 83 305 3468 3482 3980 3994 84 255 3485 3499 3997 4011 85 205 3502 3516 4014 4028 86 195 3519 3533 4031 4045 87 185 3536 3550 4048 4062 88 175 3553 3567 4065 4079 -------------------------------------------
TEXTUAL-CONVENTION    
  Unsigned32 0..4095  

TmnxSubBondingConnIdOrEmpty  
The data type TmnxSubBondingConnId represents the index of the bonding connection. The value '0' means that index is not specified.
TEXTUAL-CONVENTION    
  Unsigned32 0 | 1..2  

TBurstLimitOverride  
An explicit shaping burst size for a queue. or scheduler or aggregate-rate-limit. The value -1 means that the actual value is derived from the corresponding buffer policy's default value. A value of -2 specifies no override.
TEXTUAL-CONVENTION    
  Integer32 -2 | -1 | 1..14000000  

TmnxEvpnMHEthSegStatus  
The TmnxEvpnMHEthSegStatus data type is an enumerated integer that describes the status of an ethernet segment associated with the given SAP or SDP binding.
TEXTUAL-CONVENTION    
  INTEGER df(1), ndf(2), notesmanaged(3)  

TmnxVxlanInstance  
The TmnxVxlanInstance data type indicates range for the VXLAN instance.
TEXTUAL-CONVENTION    
  Unsigned32 1  

TmnxSvcEvpnMplsTransportType  
The type of this transport entity.
TEXTUAL-CONVENTION    
  INTEGER invalid(0), local(1), static(2), rsvp(3), ldp(4), ospf(5), isis(6), bgp(7), srTe(8), udp(9)  

TmnxMplsLabel  
The TmnxMplsLabel data type indicates range for MPLS label.
TEXTUAL-CONVENTION    
  Unsigned32 32..1048575  

TmnxMplsLabelOrZero  
The TmnxMplsLabelOrZero data type indicates range for MPLS label. The value 0 indicates that no MPLS label is specified.
TEXTUAL-CONVENTION    
  Unsigned32 0 | 32..1048575  

TmnxVni  
The TmnxVni data type indicates range for VNI.
TEXTUAL-CONVENTION    
  Unsigned32 1..16777215  

TProfileUseDEOrNone  
This textual-convention specifies the profile marking of a packet. Value of 'in' specifies in-profile marking. Value of 'out' specifies out-profile marking. Value of 'de' specifies that the profile marking of the packet will be based on the DE (Drop-Eligible) bit of the packet. DE bit value of '0' specifies in-profile and DE bit value of '1' specifies out-profile marking. Value of 'none' specifies the profile marking of the packet will be inherited from the existing enqueuing priority derived from earlier matches in the classification hierarchy.
TEXTUAL-CONVENTION    
  INTEGER none(0), in(1), out(2), de(3)  

TProfileOrDei  
the profile marking of a packet at the ingress.
TEXTUAL-CONVENTION    
  INTEGER in(1), out(2), use-dei(13)  

TDEProfileOrDei  
This textual-convention specifies the profile marking of a packet. Value of 'in' specifies the in-profile marking. Value of 'out' specifies the out-profile marking. Value of 'de' specifies that the profile marking will be based on the DE (Drop-Eligible) bit. DE bit-value of '0' specifies in-profile and DE bit value of '1' specifies out-profile marking.
TEXTUAL-CONVENTION    
  INTEGER in(1), out(2), de(3), use-dei(13)  

TmnxMobGwId  
The data type TmnxMobGwId identifies mobile gateways.
TEXTUAL-CONVENTION    
  Unsigned32 1..8  

TmnxMobGwType  
The data type TmnxMobGwType describes the mobile gateway type.
TEXTUAL-CONVENTION    
  INTEGER sgw(1), pgw(2), wlanGw(3)  

TmnxMobNode  
The data type TmnxMobNode describes the name of a mobile gateway which consists of Mobile Country Code (MCC), Mobile Network Code (MNC), Region string, Group Id, Node Id. A mobile gateway name can be described as follows: ..... MCC : 3 digits (000-999) MNC : 2 or 3 digits Application Type : SGW or PGW (3 characters) Region String : 10 characters Group Id : 3 characters Node Id : 3 characters
TEXTUAL-CONVENTION    
  DisplayString Size(0..30)  

TmnxMobProfName  
The data type TmnxMobProfName describes the name of a profile used by mobile gateways.
TEXTUAL-CONVENTION    
  TNamedItem  

TmnxMobPathMgmtState  
The data type TmnxMobPathMgmtState describes the state of a path for a reference point. A value of 'reqTimeOut' indicates that the peer is not replying to the Echo Request messages the SGW is sending out.
TEXTUAL-CONVENTION    
  INTEGER disabled(0), up(1), reqTimeOut(2), fault(3), idle(4), restart(5)  

TmnxMobPeerType  
The data type TmnxMobPeerType describes the type of the mobile gateway peer as Serving Gateway (SGW), Packet Data Network Gateway (PGW) or High Rate Packet Data (HRPD) Serving Gateway (HSGW).
TEXTUAL-CONVENTION    
  INTEGER sgw(1), pgw(2), hsgw(3)  

TmnxMobDiaPathMgmtState  
The data type TmnxMobDiaPathMgmtState describes the state of a path for a diameter connection.
TEXTUAL-CONVENTION    
  INTEGER shutDown(0), shuttingDown(1), inactive(2), active(3)  

TmnxMobDiaDetailPathMgmtState  
The data type TmnxMobDiaDetailPathMgmtState describes the detail state of a path for a diameter connection.
TEXTUAL-CONVENTION    
  INTEGER error(0), idle(1), closed(2), localShutdown(3), remoteClosing(4), waitConnAck(5), waitCea(6), open(7), openCoolingDown(8), waitDns(9)  

TmnxMobDfPeerId  
The data type TmnxMobDfPeerId identifies Delivery Function (DF) peer for the mobile gateways.
TEXTUAL-CONVENTION    
  Unsigned32 1..16  

TmnxMobLiTargetType  
The data type TmnxMobLiTargetType describes the types of target in Lawful Interception (LI).
TEXTUAL-CONVENTION    
  INTEGER imsi(1), msisdn(2), imei(3)  

TmnxMobLiTarget  
The data type TmnxMobLiTarget describes the target for the interception. The target can be of type International Mobile Subscriber Identity (IMSI), Mobile Subscriber Integrated Services Digital Network (MSISDN) or International Mobile Equipment Identity (IMEI). IMSI is defined as a number consisting of up to 15 BCD digits. The first 3 digits are the Mobile Country Code (MCC). The next 2 or 3 digits are the Mobile Network Code (MNC). The value of MCC determines whether the MNC is 2 digits or 3 digits. The remaining digits are the Mobile Subscriber Identification Number (MSIN). The internal representation of the IMSI is as follows: Bits 63-62 are reserved. Bits 61-60 indicate the length of the MNC field: 10 indicates a 2-digit MNC while 11 indicates a 3-digit MNC. Bits 59-0 hold the 15 IMSI BCD digits D1-15. When the total number of digits in the IMSI is less than 15, the nibble 0xf is used a filler. IMSI encoding for a 2-digit MNC: 63 55 47 39 0 +-----------+-----------+-----------+-------------------------+ | 0010| MCC1| MCC2| MCC3| MNC1| MNC2| MSIN (up to 10 digits) +-----------+-----------+-----------+-------------------------+ IMSI encoding for a 3-digit MNC: 63 55 47 39 35 0 +-----------+-----------+-----------+-------------------------+ | 0011| MCC1| MCC2| MCC3| MNC1| MNC2| MNC3| MSIN (up to 9 digits) +-----------+-----------+-----------+-------------------------+ Bits 63-56 of the IMSI are carried in octet number 1 of the octet string and bits 7-0 are carried in octet number 8 of the octet string.
TEXTUAL-CONVENTION    
  OCTET STRING Size(8)  

TmnxMobBufferLimit  
The data type TmnxMobBufferLimit describes the buffer limit in bytes.
TEXTUAL-CONVENTION    
  Unsigned32 1000..12000  

TmnxMobQueueLimit  
The data type TmnxMobQueueLimit describes the queue limit in bytes.
TEXTUAL-CONVENTION    
  Unsigned32 1000..12000  

TmnxMobDiaTransTimer  
The data type TmnxMobDiaTransTimer describes the diameter peer transaction timer value in seconds.
TEXTUAL-CONVENTION    
  Unsigned32 1..180  

TmnxMobProfIpTtl  
The data type TmnxMobProfIpTtl describes the Time-To-Live (TTL) value.
TEXTUAL-CONVENTION    
  Unsigned32 1..255  

TmnxMobProfNameOrEmpty  
The data type TmnxMobProfNameOrEmpty describes the name of a profile used by mobile gateways.
TEXTUAL-CONVENTION    
  TNamedItemOrEmpty  

TmnxMobDiaPeerHost  
The data type TmnxMobDiaPeerHost describes the name of a destination realm, originating realm and originating host.
TEXTUAL-CONVENTION    
  DisplayString Size(0..80)  

TmnxMobMcc  
The data type TmnxMobMcc describes the Mobile Country Code (MCC) of an User Equipment (UE).
TEXTUAL-CONVENTION    
  DisplayString Size(3)  

TmnxMobMnc  
The data type TmnxMobMnc describes the Mobile Network Code (MNC) of an User Equipment (UE).
TEXTUAL-CONVENTION    
  DisplayString Size(2|3)  

TmnxMobQciValueOrZero  
The data type TmnxMobQciValueOrZero describes the QoS Class Identifier (QCI) value.
TEXTUAL-CONVENTION    
  Unsigned32 0..9  

TmnxMobArpValueOrZero  
The data type TmnxMobArpValueOrZero describes the Allocation and Retention Priority (ARP) value.
TEXTUAL-CONVENTION    
  Unsigned32 0..15  

TmnxMobStaticPolPrecedenceOrZero  
The data type TmnxMobStaticPolPrecedence describes the precedence value for a static policy configured in the system.
TEXTUAL-CONVENTION    
  Unsigned32 0..65535  

TmnxMobQciValue  
The data type TmnxMobQciValue describes the QoS Class Identifier (QCI) value.
TEXTUAL-CONVENTION    
  Unsigned32 1..9  

TmnxMobArpValue  
The data type TmnxMobArpValue describes the Allocation and Retention Priority (ARP) value.
TEXTUAL-CONVENTION    
  Unsigned32 1..15  

TmnxMobMccOrEmpty  
The data type TmnxMobMccOrEmpty describes the Mobile Country Code (MCC) of an User Equipment (UE).
TEXTUAL-CONVENTION    
  DisplayString Size(0|3)  

TmnxMobMncOrEmpty  
The data type TmnxMobMncOrEmpty describes the Mobile Network Code (MNC) of an User Equipment (UE).
TEXTUAL-CONVENTION    
  DisplayString Size(0|2|3)  

TmnxMobChargingProfile  
The data type TmnxMobChargingProfile describes the charging trigger rules applied for generating Charging Data Records (CDR) for subscribers.
TEXTUAL-CONVENTION    
  Unsigned32 0..255  

TmnxMobProfGbrRate  
The data type TmnxMobProfGbrRate describes the Guaranteed Bit Rate (GBR) value in kilo-bits per second(kbps).
TEXTUAL-CONVENTION    
  Unsigned32 0..100000  

TmnxMobProfMbrRate  
The data type TmnxMobProfMbrRate describes the Maximum Bit Rate (MBR) value in kilo-bits per second(kbps).
TEXTUAL-CONVENTION    
  Unsigned32 0..100000  

TmnxMobProfPolReportingLevel  
TmnxMobProfPolReportingLevel data type is an enumerated integer that describes the Reporting level for the Policy and Charging Control (PCC) rule.
TEXTUAL-CONVENTION    
  INTEGER servId(1), ratingGrp(2)  

TmnxMobProfPolChargingMethod  
TmnxMobProfPolChargingMethod data type is an enumerated integer that describes the Charging Method for the Policy and Charging Control (PCC) rule. A variable of this type could be set to 'online' charging method, 'offline' charging method or 'both'. If the variable is set to 'profChargingMtd' the charging method is set to 'offline' if 'tmnxMobProfPgwChrgOffLineState' is set to 'enabled', the charging method is set to 'online' if 'tmnxMobProfPgwChrgGyState' is set to 'enabled' and the charging method is set to 'both' if both 'tmnxMobProfPgwChrgOffLineState' and 'tmnxMobProfPgwChrgGyState' are set to 'enabled'.
TEXTUAL-CONVENTION    
  INTEGER profChargingMtd(0), online(1), offline(2), both(3)  

TmnxMobProfPolMeteringMethod  
TmnxMobProfPolMeteringMethod data type is an enumerated integer that describes the Metering Method for the Policy and Charging Control (PCC) rule.
TEXTUAL-CONVENTION    
  INTEGER timeBased(1), volBased(2), both(3)  

TmnxMobStaticPolPrecedence  
The data type TmnxMobStaticPolPrecedence describes the precedence value for a static policy configured in the system.
TEXTUAL-CONVENTION    
  Unsigned32 1..65536  

TmnxMobRtrAdvtInterval  
The data type TmnxMobRtrAdvtInterval describes the router advertisement interval in minutes.
TEXTUAL-CONVENTION    
  Unsigned32 1..60  

TmnxMobRtrAdvtLifeTime  
The data type TmnxMobRtrAdvtLifeTime describes the router advertisement life time in hours.
TEXTUAL-CONVENTION    
  Unsigned32 1..24  

TmnxMobAddrScheme  
The data type TmnxMobAddrScheme describes the addressing scheme. If the value is set to 'stateful', User Equipment (UE) uses DHCPv6 to get IPv6 address. If the value is set to 'stateless', UE uses ICMPv6 to get IPv6 address.
TEXTUAL-CONVENTION    
  INTEGER stateful(1), stateless(2)  

TmnxMobDiaRetryCount  
The data type TmnxMobDiaRetryCount describes the diameter peer retry count value.
TEXTUAL-CONVENTION    
  Unsigned32 0..8  

TmnxMobDualStackPref  
The data type TmnxMobDualStackPref describes the preference in a dual IP stack. The value 'useCplane' specifies that the value is inherited from the preference in a dual IP stack on control plane.
TEXTUAL-CONVENTION    
  INTEGER ipv4(1), ipv6(2), useCplane(3)  

TmnxMobRfAcctLevel  
TmnxMobRfAcctLevel data type is an enumerated integer that describes the accounting level.
TEXTUAL-CONVENTION    
  INTEGER pdnLevel(1), qciLevel(2)  

TmnxMobApn  
The data type TmnxMobApn describes the Access Point Name (APN) associated with an User Equipment (UE).
TEXTUAL-CONVENTION    
  DisplayString Size(1..80)  

TmnxMobChargingProfileOrInherit  
The data type TmnxMobChargingProfileOrInherit describes the charging trigger rules applied for generating Charging Data Records (CDR) for subscribers. A value of '-1' indicates that identifier will be inherited from another object that is usually in another mib table.
TEXTUAL-CONVENTION    
  Integer32 -1 | 0..255  

TmnxMobUeId  
The data type TmnxMobUeId describes the identity of an User Equipment. TmnxMobUeId can be of the following types: International Mobile Subscriber Identity (IMSI), International Mobile station Equipment Identity (IMEI), Mobile Subscriber Integrated Services Digital network Number (MSISDN). IMSI, IMEI, MSISDN are defined in 3GPP TS 23.003. IMSI is defined as a number consisting of up to 15 BCD digits. The first 3 digits are the Mobile Country Code (MCC). The next 2 or 3 digits are the Mobile Network Code (MNC). The value of MCC determines whether the MNC is 2 digits or 3 digits. The remaining digits are the Mobile Subscriber Identification Number (MSIN). IMEI is defined as a number consisting of up to 16 BCD digits. The first 8 digits consists of Type Allocation Code (TAC). The next 6 digits consist of Serial Number (SNR) which could be followed by a Check Digit (CD) or Spare Digit (SD) of size 1 digit or by a Software Version Number (SVN) of size 2 digits. MSISDN is defined as a number consisting of 9 to 15 BCD digits. MSISDN consists of Country Code (CC) followed by National Destination Code (NDC) and Subscriber Number (SN). Bits 63-56 of the IMSI or IMEI or MSISDN are carried in octet number 1 of the octet string and bits 7-0 are carried in octet number 8 of the octet string. The internal representation of the IMSI is as follows: Bits 63-62 are reserved. Bits 61-60 indicate the length of the MNC field: 10 indicates a 2-digit MNC while 11 indicates a 3-digit MNC. Bits 59-0 hold the 15 IMSI BCD digits D1-15. When the total number of digits in the IMSI is less than 15, the nibble 0xf is used a filler. IMSI encoding for a 2-digit MNC: 63 55 47 39 0 +-----------+-----------+-----------+-------------------------+ | 0010| MCC1| MCC2| MCC3| MNC1| MNC2| MSIN (up to 10 digits) +-----------+-----------+-----------+-------------------------+ IMSI encoding for a 3-digit MNC: 63 55 47 39 35 0 +-----------+-----------+-----------+-------------------------+ | 0011| MCC1| MCC2| MCC3| MNC1| MNC2| MNC3| MSIN (up to 9 digits) +-----------+-----------+-----------+-------------------------+ The internal representation of the IMEI and MSISDN is as follows: IMEI encoding: 63 55 31 7 0 +-----------+-----------+----------------------+-------+ | TAC | SNR | SNV | |N2|N1|N4|N3|N6|N5|N8|N7|N10|N9|N12|N11|N14|N13|N16|N15| +-----------+-----------+-----------+------------------+ MSISDN encoding: 63 55 31 7 0 +-----------+-----------+----------------------+-------+ | CC | NDC | SN | |N2|N1|N4|N3|N6|N5|N8|N7|N10|N9|N12|N11|N14|N13|N16|N15| +-----------+-----------+-----------+------------------+ When the total number of digits in the IMEI or MSISDN is less than 15, the nibble 0x0 is used a filler. In each byte both nibbles are swapped and it is stored as shown in the above format. For example, in the format N3 & N4 present the nibble number 3 and 4 respectively and they are stored in reverse order. When the total number of digits are odd in IMEI and MSISDB, the last digit will be paired with nibble 0xf.
TEXTUAL-CONVENTION    
  OCTET STRING Size(8)  

TmnxMobMsisdn  
The data type TmnxMobMsisdn describes the Mobile Subscriber Integrated Services Digital Network (MSISDN) number of an User Equipment (UE).
TEXTUAL-CONVENTION    
  DisplayString Size(0..15)  

TmnxMobImei  
The data type TmnxMobImei describes the International Mobile Equipment Identity (IMEI) of an User Equipment (UE).
TEXTUAL-CONVENTION    
  DisplayString Size(0|16)  

TmnxMobNai  
The data type TmnxMobNai describes the Network Address Identifier (NAI) of an User Equipment (UE).
TEXTUAL-CONVENTION    
  DisplayString Size(0..72)  

TmnxMobMnc  
The data type TmnxMobMnc describes the Mobile Network Code (MNC) of an User Equipment (UE).
TEXTUAL-CONVENTION    
  DisplayString Size(2|3)  

TmnxMobUeState  
The data type TmnxMobUeState describes the state of an User Equipment (UE).
TEXTUAL-CONVENTION    
  INTEGER idle(1), active(2), paging(3), init(4), suspend(5), ddnDamp(6)  

TmnxMobUeRat  
The data type TmnxMobUeRat describes the Radio Access Type (RAT) of an User Equipment (UE).
TEXTUAL-CONVENTION    
  INTEGER utran(1), geran(2), wlan(3), gan(4), hspa(5), eutran(6), ehrpd(7), hrpd(8), oneXrtt(9), umb(10)  

TmnxMobUeSubType  
The data type TmnxMobUeSubType describes the subscription type of User Equipment (UE).
TEXTUAL-CONVENTION    
  INTEGER homer(1), roamer(2), visitor(3)  

TmnxMobPdnType  
The data type TmnxMobPdnType describes the type of a Pakcet Data Network (PDN).
TEXTUAL-CONVENTION    
  INTEGER ipv4(1), ipv6(2), ipv4v6(3)  

TmnxMobPgwSigProtocol  
The data type TmnxMobPgwSigProtocol describes the signaling protocol used on S5 or S8 reference point.
TEXTUAL-CONVENTION    
  INTEGER gtp(1), pmip(2)  

TmnxMobPdnSessionState  
The data type TmnxMobPdnSessionState describes the feedback signaling message (FSM) state of a Packet Data Network (PDN) session.
TEXTUAL-CONVENTION    
  INTEGER invalid(0), init(1), waitPcrfResponse(2), waitPgwResponse(3), waitEnodebUpdate(4), connected(5), ulDelPending(6), dlDelPending(7), idleMode(8), pageMode(9), dlHandover(10), incomingHandover(11), outgoingHandover(12), stateMax(13)  

TmnxMobPdnSessionEvent  
The data type TmnxMobPdnSessionEvent describes the feedback signaling message (FSM) event of a Packet Data Network (PDN) session.
TEXTUAL-CONVENTION    
  INTEGER sessionInvalid(0), gtpCreateSessReq(1), gtpUpdateBearerReq(2), gtpDeleteSessReq(3), gtpDeleteBearerResp(4), gtpUpdateBearerResp(5), gtpModifyActiveToIdle(6), gtpResrcAllocCmd(7), gtpModifyQosCmd(8), gtpX1eNodeBTeidUpdate(9), gtpX2SrcSgwDeleteSessReq(10), gtpS1CreateIndirectTunnel(11), dlPktRecvIndication(12), dlPktNotificationAck(13), dlPktNotificationFail(14), pcrfSessEstResp(15), pcrfSessTerminateRsp(16), pcrfProvQosRules(17), pmipSessResp(18), pmipSessUpdate(19), pmipSessDeleteRsp(20), pmipSessDeleteReq(21), eventMax(22)  

TmnxMobUeIdType  
The data type TmnxMobUeIdType describes the types of identification for User Equipment (UE).
TEXTUAL-CONVENTION    
  INTEGER imsi(0), imei(1), msisdn(2)  

TmnxMobImsiStr  
The data type TmnxMobImsiStr describes the International Mobile Subscriber Identity (IMSI) of a User Equipment (UE).
TEXTUAL-CONVENTION    
  DisplayString Size(0|9..15)  

TmnxMobBearerId  
The data type TmnxMobBearerId describes the bearer identifier.
TEXTUAL-CONVENTION    
  Unsigned32 1..15  

TmnxMobBearerType  
The data type TmnxMobBearerType describes the type of a bearer.
TEXTUAL-CONVENTION    
  INTEGER default(1), dedicated(2)  

TmnxMobQci  
The data type TmnxMobQci describes the QoS Class Identifier.
TEXTUAL-CONVENTION    
  Unsigned32 0..9  

TmnxMobArp  
The data type TmnxMobArp describes the QoS parameter, Allocation and Retention Priority (ARP).
TEXTUAL-CONVENTION    
  Unsigned32 0..15  

TmnxMobSdf  
The data type TmnxMobSdf describes the number of Service Data Flows (SDFs).
TEXTUAL-CONVENTION    
  Unsigned32 0..255  

TmnxMobSdfFilter  
The data type TmnxMobSdfFilter describes a IP filter in a Service Data Flow (SDF) or Traffic Flow Template (TFT).
TEXTUAL-CONVENTION    
  Unsigned32 0..16  

TmnxMobSdfFilterNum  
The data type TmnxMobSdfFilterNum describes the number of IP filters.
TEXTUAL-CONVENTION    
  Unsigned32 0..16  

TmnxMobSdfRuleName  
The data type TmnxMobSdfRuleName describes the policy rule name of a Service Data Flow (SDF).
TEXTUAL-CONVENTION    
  DisplayString Size(1..64)  

TmnxMobSdfFilterDirection  
The data type TmnxMobSdfFilterDirection describes the direction on which a Service Data Flow (SDF) filter rule is valid.
TEXTUAL-CONVENTION    
  INTEGER preRel7(0), downLink(1), upLink(2), biDir(3)  

TmnxMobSdfFilterProtocol  
The data type TmnxMobSdfFilterProtocol describes IPv4 protocol or IPv6 next header on which Service Data Flow (SDF) filter matches.
TEXTUAL-CONVENTION    
  INTEGER any(-1), ipv6HopByOpOpt(0), icmp(1), igmp(2), ggp(3), ip(4), st(5), tcp(6), cbt(7), egp(8), igp(9), bbnRccMon(10), nvp2(11), pup(12), argus(13), emcon(14), xnet(15), chaos(16), udp(17), mux(18), dcnMeas(19), hmp(20), prm(21), xnsIdp(22), trunk1(23), trunk2(24), leaf1(25), leaf2(26), rdp(27), irdp(28), isoTp4(29), netblt(30), mfeNsp(31), meritInp(32), dccp(33), pc3(34), idpr(35), xtp(36), ddp(37), idprCmtp(38), tpplusplus(39), il(40), ipv6(41), sdrp(42), ipv6Route(43), ipv6Frag(44), idrp(45), rsvp(46), gre(47), dsr(48), bna(49), esp(50), ah(51), iNlsp(52), swipe(53), narp(54), mobile(55), tlsp(56), skip(57), ipv6Icmp(58), ipv6NoNxt(59), ipv6Opts(60), anyHostIntl(61), cftp(62), anyLocalNet(63), satExpak(64), kryptolan(65), rvd(66), ippc(67), anyDFS(68), satMon(69), visa(70), ipcv(71), cpnx(72), cphb(73), wsn(74), pvp(75), brSatMon(76), sunNd(77), wbMon(78), wbExpak(79), isoIp(80), vmtp(81), secureVmpt(82), vines(83), ttp(84), nsfnetIgp(85), dgp(86), tcf(87), eiGrp(88), ospfIgp(89), spriteRpc(90), larp(91), mtp(92), ax25(93), ipip(94), micp(95), sccSp(96), etherIp(97), encap(98), anyPEC(99), gmtp(100), ifmp(101), pnni(102), pim(103), aris(104), scps(105), qnx(106), activeNet(107), ipComp(108), snp(109), compaqPeer(110), ipxInIp(111), vrrp(112), pgm(113), any0hop(114), l2tp(115), ddx(116), iatp(117), stp(118), srp(119), uti(120), smp(121), sm(122), ptp(123), isis(124), fire(125), crtp(126), crudp(127), sscopmce(128), iplt(129), sps(130), pipe(131), sctp(132), fc(133), rsvpE2eIgnore(134), mobHeader(135), udpLite(136), mplsInIp(137), manet(138), hip(139), shim6(140)  

TmnxMobServerState  
The data type TmnxMobServerState describes the state of a server connected with a mobile gateway.
TEXTUAL-CONVENTION    
  INTEGER na(0), up(1), down(2)  

TmnxMobChargingBearerType  
The data type TmnxMobChargingBearerType describes the type of a bearer context used in charging applications.
TEXTUAL-CONVENTION    
  INTEGER home(1), visiting(2), roaming(3)  

TmnxMobChargingLevel  
The data type TmnxMobChargingLevel describes the level where the charging is done.
TEXTUAL-CONVENTION    
  INTEGER pdn(1), bearer(2)  

TmnxMobIpCanType  
The data type TmnxMobIpCanType describes the type of Internet Protocol Connectivity Access Network (IP-CAN) session as Evolved Packet Core (epc3gpp) or GPRS (gprs3gpp).
TEXTUAL-CONVENTION    
  INTEGER epc3gpp(1), gprs3gpp(2)  

TmnxMobServRefPointType  
The data type TmnxMobServRefPointType describes the types of reference point.
TEXTUAL-CONVENTION    
  INTEGER s5(1), s8(2), s2a(4)  

TmnxMobAccessType  
The data type TmnxMobAccessType describes the various access types. eps - evolved packet system. gprs - general packet radio services. non3gpp - trusted non-3gpp network such as evolved High Rate Packet Data (eHRPD) and untrusted non-3gpp network.
TEXTUAL-CONVENTION    
  INTEGER eps(1), gprs(2), non3gpp(3)  

TmnxMobUeStrPrefix  
The data type TmnxMobUeStrPrefix describes the prefix for International Mobile Subscriber Identity (IMSI) or Mobile Subscriber Integrated Services Digital Network (MSISDN) of an User Equipment (UE).
TEXTUAL-CONVENTION    
  DisplayString Size(4..15)  

TmnxMobApnOrZero  
The data type TmnxMobApnOrZero describes the Access Point Name (APN) associated with an User Equipment (UE).
TEXTUAL-CONVENTION    
  DisplayString Size(0..80)  

TmnxMobAuthType  
The data type TmnxMobAuthType describes the authentication type used by mobile gateways.
TEXTUAL-CONVENTION    
  INTEGER radius(1), diameter(2)  

TmnxMobAuthUserName  
The data type TmnxMobAuthUserName describes the user name used in authentication requests by mobile gateways.
TEXTUAL-CONVENTION    
  INTEGER imsi(1), msisdn(2), pco(3)  

TmnxMobPdnRefPointType  
The data type TmnxMobPdnRefPointType describes the types of reference point.
TEXTUAL-CONVENTION    
  INTEGER s5(1), s8(2), gn(3), s2a(4), gp(5)  

TmnxMobRatingGrpState  
The data type TmnxMobRatingGrpState describes the state of a rating group. allowFlow - Allow the traffic to flow disallowFlow - Disallow the traffic to Flow redWebPortal - Redirect the traffic to web portal allowResRules - Allow restricted rules iom1stPktTrigger - Get the trigger from on IOM on arrival of 1st packet dis1stPktTrigger - Disable 1st packet trigger and allow the traffic creditsToppedUp - Credits topped up waitForFpt - Unblocked and waiting for First Packet Trigger (FPT)
TEXTUAL-CONVENTION    
  INTEGER allowFlow(1), disallowFlow(2), redWebPortal(3), allowResRules(4), iom1stPktTrigger(5), dis1stPktTrigger(6), creditsToppedUp(7), waitForFpt(8)  

TmnxMobPresenceState  
The data type TmnxMobPresenceState describes the whether the given field is present.
TEXTUAL-CONVENTION    
  INTEGER absent(0), present(1)  

TmnxMobPdnGyChrgTriggerType  
The data type TmnxMobPdnGyChrgTriggerType describes type of the trigger activated by the Online Charging System (OCS). sgsnIpAddrRecvd - Change in Serving GPRS Support Node (SGSN) IP address qosRecvd - Change in Quality of Service (QoS) locRecvd - Location Change ratRecvd - Router Advertisement Trigger (RAT) Change qosTrfClsRecvd - Change in QoS Traffic class qosRlbClsRecvd - Change in QoS Reliability class qosDlyClsRecvd - Change in QoS Delay class qosPeakThrptRecvd - Change in QoS Peak Throughput qosPrcClsRecvd - Change in QoS Precedence class qosMeanTrptRecvd - Change in QoS Mean Throughput qosMxBtRtUplnkRecvd - Change in QoS MBR for Uplink qosMxBtRtDllnkRecvd - Change in QoS MBR for Downlink qosResBerRecvd - Change in QoS Residual Bit Error Rate (BER) qosSduErrRatRecvd - Change in QoS Service Data Unit (SDU) Error Ratio class qosTransDelayRecvd - Change in QoS Transfer Delay qosTrfHndPriRecvd - Change in QoS Traffic Handling Priority qosGrtBtRtUplnkRecvd - Change in QoS Guaranteed Bit Rate (GBR) for Uplink qosGrtBtRtDllnkRecvd - Change in QoS GBR for Downlink locMccRecvd - Change in Location Mobile Country Code (MCC) locMncRecvd - Change in Location Mobile Network Code (MNC) locRacRecvd - Change in Location Routing Area Code (RAC) locLacRecvd - Change in Location Location Area Code (LAC) locCellIdRecvd - Change in Location Cell ID medCompRecvd - Change in Media Composition partcNmbRecvd - Change in Participants' number thrldPartcNmbRecvd - Change in Threshold of Participants' number usrPartcTypeRecvd - Change in User Participating Type servCondRecvd - Change in Service Condition servNodeRecvd - Change in Service Node usrCsgInfoRecvd - Change in User Closed Subscription Group (CSG) Information
TEXTUAL-CONVENTION    
  INTEGER sgsnIpAddrRecvd(0), qosRecvd(1), locRecvd(2), ratRecvd(3), qosTrfClsRecvd(4), qosRlbClsRecvd(5), qosDlyClsRecvd(6), qosPeakThrptRecvd(7), qosPrcClsRecvd(8), qosMeanTrptRecvd(9), qosMxBtRtUplnkRecvd(10), qosMxBtRtDllnkRecvd(11), qosResBerRecvd(12), qosSduErrRatRecvd(13), qosTransDelayRecvd(14), qosTrfHndPriRecvd(15), qosGrtBtRtUplnkRecvd(16), qosGrtBtRtDllnkRecvd(17), locMccRecvd(18), locMncRecvd(19), locRacRecvd(20), locLacRecvd(21), locCellIdRecvd(22), medCompRecvd(23), partcNmbRecvd(24), thrldPartcNmbRecvd(25), usrPartcTypeRecvd(26), servCondRecvd(27), servNodeRecvd(28), usrCsgInfoRecvd(29)  

TMplsLspExpProfMapID  
The identification number of a MPLS LSP EXP profile.
TEXTUAL-CONVENTION    
  TPolicyID 1..65535  

TSysResource  
The resource allocated for a particular application. The value -1 means maximum rate.
TEXTUAL-CONVENTION    
  Integer32 -1 | 0..11  

ServObjDesc  
ASCII string used to describe various service objects.
TEXTUAL-CONVENTION    
  DisplayString Size(0..80)  

TSapIngressMeterId  
Ingress Meter Id
TEXTUAL-CONVENTION    
  INTEGER 0 | 1..32  

TNetworkIngressMeterId  
Ingress Meter Id
TEXTUAL-CONVENTION    
  INTEGER 0 | 1..16  

TmnxVwmCardType  
The TmnxVwmCardType data type is an enumerated integer that describes the values used to identify the VWM Shelf Card type.
TEXTUAL-CONVENTION    
  INTEGER not-provisioned(0), not-equipped(1), sfc1A(2), sfc1B(3), sfc1C(4), sfc1D(5), sfc1E(6), sfc1F(7), sfc1G(8), sfc1H(9), sfc2AandB(10), sfc2CandD(11), sfc2EandF(12), sfc2GandH(13), sfc4A-D(14), sfc4E-H(15), sfc8(16), sfd8A-R(17), sfd8B-R(18), sfd8C-R(19), sfd8D-R(20), sfd4A-R(21), sfd4B-R(22), sfd4C-R(23), sfd4D-R(24), sfd4E-R(25), sfd4F-R(26), sfd4G-R(27), sfd4H-R(28), sfd2A-R(29), sfd2B-R(30), sfd2C-R(31), sfd2D-R(32), sfd2E-R(33), sfd2F-R(34), sfd2G-R(35), sfd2H-R(36), sfd2I-R(37), sfd2L-R(38), sfd2M-R(39), sfd2N-R(40), sfd2O-R(41), sfd2P-R(42), sfd2Q-R(43), sfd2R-R(44)  

Defined Values

timetraTCMIBModule 1.3.6.1.4.1.6527.1.1.2
This document is the SNMP MIB module for the SNMP Textual Conventions (TCs) used in the Nokia SROS manageability instrumentation. Copyright 2003-2017 Nokia. All rights reserved. Reproduction of this document is authorized on the condition that the foregoing copyright notice is included. This SNMP MIB module (Specification) embodies Nokia's proprietary intellectual property. Nokia retains all title and ownership in the Specification, including any revisions. Nokia grants all interested parties a non-exclusive license to use and distribute an unmodified copy of this Specification in connection with management of Nokia products, and without fee, provided this copyright notice and license appear on all copies. This Specification is supplied `as is', and Nokia makes no warranty, either express or implied, as to the use, operation, condition, or performance of the Specification.
MODULE-IDENTITY