TN-MGMT-TDM-MIB

File: TN-MGMT-TDM-MIB.mib (14593 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC ENTITY-MIB
IF-MIB TN-MGMT-MIB TRANSITION-TC

Imported symbols

MODULE-IDENTITY OBJECT-IDENTITY enterprises
TimeStamp TruthValue DisplayString
entPhysicalIndex InterfaceIndexOrZero InterfaceIndex
tnMgmtNotifications tnInterfaceMgmt CpsConnector

Defined Types

TnIfTDMEntry  
SEQUENCE    
  tnIfTDMAISTransmit INTEGER
  tnIfTDMAISFormat INTEGER
  tnIfTDMAlarmIndicationSignal INTEGER
  tnIfTDMLongHaul INTEGER
  tnIfTDMType INTEGER
  tnIfTDMT1E1LineBuildout INTEGER
  tnIfTDMDS3E3LineBuildout INTEGER
  tnIfTDMConnectorType CpsConnector

TnIfTDMExtEntry  
SEQUENCE    
  tnIfTDMExtId INTEGER
  tnIfTDMExtAISTrasmit INTEGER
  tnIfTDMExtAISFormat INTEGER
  tnIfTDMExtAlarmIndicationSingnal INTEGER
  tnIfTDMExtLoopback INTEGER
  tnIfTDMExtYellowTrasmit INTEGER

TnIfTDM2Entry  
SEQUENCE    
  tnIfTDM2FiberLineNum INTEGER
  tnIfTDM2FiberActiveLine INTEGER
  tnIfTDM2FiberRevertive INTEGER
  tnIfTDM2FiberPrimaryLinkStatus INTEGER
  tnIfTDM2FiberSecondaryLinkStatus INTEGER
  tnIfTDM2InBandLPEnable INTEGER
  tnIfTDM2InBandLPStartPatten DisplayString
  tnIfTDM2InBandLPStopPatten DisplayString
  tnIfTDM2InBandPEERLPEnable INTEGER
  tnIfTDM2InBandPEERLPStartPatten DisplayString
  tnIfTDM2InBandPEERLPStopPatten DisplayString
  tnIfTDM2InBandLPTimeoutEnable INTEGER
  tnIfTDM2InBandLPTimeoutCount INTEGER
  tnIfTDM2InBandPEERLPTimeoutEnable INTEGER
  tnIfTDM2InBandPEERLPTimeoutCount INTEGER

Defined Values

tnIfTDMTable 1.3.6.1.4.1.868.2.5.3.1.2.6
This table has entries for the TDM attributes.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TnIfTDMEntry

tnIfTDMEntry 1.3.6.1.4.1.868.2.5.3.1.2.6.1
A entry in the table represents TDM attributes.
Status: current Access: not-accessible
OBJECT-TYPE    
  TnIfTDMEntry  

tnIfTDMAISTransmit 1.3.6.1.4.1.868.2.5.3.1.2.6.1.1
Transmit AIS(All Ones/BLUE) on Fiber(Copper) as an error signal when Copper interface(Fiber Interface) is down. When this error signal is transmitted, the AIS of the device on the other end is activated, if supported
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3)  

tnIfTDMAISFormat 1.3.6.1.4.1.868.2.5.3.1.2.6.1.2
Transmit AIS(All Ones:1111... sequence/BLUE:0101... sequence) on Fiber(Copper) as an error signal for DS3/E3/STS-1 port
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER allones(1), blue(2), notApplicable(3)  

tnIfTDMAlarmIndicationSignal 1.3.6.1.4.1.868.2.5.3.1.2.6.1.3
When equal to alarm(1), this means that the other end has TAOS enabled and is currently transmitting an alarm condition. when equal to normal, this means no alarm.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER alarm(1), normal(2)  

tnIfTDMLongHaul 1.3.6.1.4.1.868.2.5.3.1.2.6.1.4
This variable indicates the current position of the remote device's Short/Long haul configuration switch.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2), notApplicable(3)  

tnIfTDMType 1.3.6.1.4.1.868.2.5.3.1.2.6.1.5
This variable indicates the type of the current device. T1=1.544MHz; E1=2.048MHz;E3 = 34.4Mb/s; DS3 = 44.7Mb/s; STS-1 = 51.8Mb/s
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(0), t1(1), e1(2), j1(3), dS3(4), e3(5), sts-1(6)  

tnIfTDMT1E1LineBuildout 1.3.6.1.4.1.868.2.5.3.1.2.6.1.6
The characteristics T1E1 card's copper interface.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(0), e13-0V120ohm(1), e12-37V75ohm(2), t1SH-DSX-0-133ANSIT1403(3), t1SH-DSX-133-266(4), t1SH-DSX-266-399(5), t1SH-DSX-399-533(6), t1SH-DSX-533-655(7), t1SH-DSX-6V(8), t1LH-0dB(9), t1LH-m7-5dB(10), t1LH-m15dB(11), t1LH-m22-5dB(12)  

tnIfTDMDS3E3LineBuildout 1.3.6.1.4.1.868.2.5.3.1.2.6.1.7
The characteristics of DS3E3 card's copper interface.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER unknown(0), boost(1), normal(2)  

tnIfTDMConnectorType 1.3.6.1.4.1.868.2.5.3.1.2.6.1.8
The style of connector built into this device.
Status: current Access: read-only
OBJECT-TYPE    
  CpsConnector  

tnIfTDMExtTable 1.3.6.1.4.1.868.2.5.3.1.2.9
This table has entries for the Extral TDM attributes.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TnIfTDMExtEntry

tnIfTDMExtEntry 1.3.6.1.4.1.868.2.5.3.1.2.9.1
A entry in the table represents Extral TDM attributes.
Status: current Access: not-accessible
OBJECT-TYPE    
  TnIfTDMExtEntry  

tnIfTDMExtId 1.3.6.1.4.1.868.2.5.3.1.2.9.1.1
An index that uniquely identifies an entry in the tnIfTDMExtTable. This index permits the same interface to have several different channels
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..99999999  

tnIfTDMExtAISTrasmit 1.3.6.1.4.1.868.2.5.3.1.2.9.1.2
Transmit AIS(All Ones/BLUE) on the Channel as an error signal when Copper interface(Fiber Interface) is down. When this error signal is transmitted, the AIS of the device on the other end is activated, if supported
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3)  

tnIfTDMExtAISFormat 1.3.6.1.4.1.868.2.5.3.1.2.9.1.3
Transmit AIS(All Ones:1111... sequence/BLUE:0101... sequence) on the Channel as an error signal for the pair port
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER allones(1), blue(2), notApplicable(3)  

tnIfTDMExtAlarmIndicationSingnal 1.3.6.1.4.1.868.2.5.3.1.2.9.1.4
When equal to alarm(1), this means that the other end of Channel has AIS enabled and is currently transmitting an alarm condition. when equal to normal(2), this means no alarm. when equal to yellow(3), this means the other end of Channel has YELLOW enabled and is currently transmitting a YELLOW condition. when equal to red(4), this means the local end of Channel has detect a LOS on receiver.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER alarm(1), normal(2), yellow(3), red(4)  

tnIfTDMExtLoopback 1.3.6.1.4.1.868.2.5.3.1.2.9.1.5
This variable indicates the loopback state of the current Channel
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3)  

tnIfTDMExtYellowTrasmit 1.3.6.1.4.1.868.2.5.3.1.2.9.1.6
Transmit Yellow on the Channel as an error signal when Local Copper Interface is down. When this error signal is transmitted.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3)  

tnIfTDM2Table 1.3.6.1.4.1.868.2.5.3.1.2.10
This table has entries for the TDM 2 attributes.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TnIfTDM2Entry

tnIfTDM2Entry 1.3.6.1.4.1.868.2.5.3.1.2.10.1
A entry in the table represents the TDM 2 attributes.
Status: current Access: not-accessible
OBJECT-TYPE    
  TnIfTDM2Entry  

tnIfTDM2FiberLineNum 1.3.6.1.4.1.868.2.5.3.1.2.10.1.1
This variable is indicate the links number of the Fiber Port, maybe single line or dual line
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

tnIfTDM2FiberActiveLine 1.3.6.1.4.1.868.2.5.3.1.2.10.1.2
This variable is indicate the active fiber link, if a multi-fiber line is used for hardware redundancy
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER primary(0), secondary(1)  

tnIfTDM2FiberRevertive 1.3.6.1.4.1.868.2.5.3.1.2.10.1.3
This variable is used to decide whether to revertive the fiber link to primary link if applicable
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3)  

tnIfTDM2FiberPrimaryLinkStatus 1.3.6.1.4.1.868.2.5.3.1.2.10.1.4
This variable indicates the fiber port primary line link status
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), testing(3), unknown(4)  

tnIfTDM2FiberSecondaryLinkStatus 1.3.6.1.4.1.868.2.5.3.1.2.10.1.5
This variable indicates the fiber port secondary line link status
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), testing(3), unknown(4)  

tnIfTDM2InBandLPEnable 1.3.6.1.4.1.868.2.5.3.1.2.10.1.6
This variable indicates whether In-band Loopback detect is enabled
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3)  

tnIfTDM2InBandLPStartPatten 1.3.6.1.4.1.868.2.5.3.1.2.10.1.7
This binary string is used to set the In-band Loopback start Patten, such as 11000 string
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

tnIfTDM2InBandLPStopPatten 1.3.6.1.4.1.868.2.5.3.1.2.10.1.8
This binary string is used to set the In-band Loopback stop Patten, such as 11100 string
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

tnIfTDM2InBandPEERLPEnable 1.3.6.1.4.1.868.2.5.3.1.2.10.1.9
This variable indicates whether the PEER interface In-band Loopback detect is enabled
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3)  

tnIfTDM2InBandPEERLPStartPatten 1.3.6.1.4.1.868.2.5.3.1.2.10.1.10
This binary string is used to set the PEER interface In-band Loopback start Patten, such as 11000 string
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

tnIfTDM2InBandPEERLPStopPatten 1.3.6.1.4.1.868.2.5.3.1.2.10.1.11
This binary string is used to set the PEER interface In-band Loopback stop Patten, such as 11100 string
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

tnIfTDM2InBandLPTimeoutEnable 1.3.6.1.4.1.868.2.5.3.1.2.10.1.12
This variable indicates whether the In-band Loopback timeout watchdog is enabled
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3)  

tnIfTDM2InBandLPTimeoutCount 1.3.6.1.4.1.868.2.5.3.1.2.10.1.13
This variable is used to set the In-band Loopback timeout watchdog value, the unit is minute
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..4095  

tnIfTDM2InBandPEERLPTimeoutEnable 1.3.6.1.4.1.868.2.5.3.1.2.10.1.14
This variable indicates whether the Peer In-band Loopback timeout watchdog is enabled
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), notApplicable(3)  

tnIfTDM2InBandPEERLPTimeoutCount 1.3.6.1.4.1.868.2.5.3.1.2.10.1.15
This variable is used to set the Peer In-band Loopback timeout watchdog value, the unit is minute
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..4095  

tnIfTDMAlarmIndicationSignalEvt 1.3.6.1.4.1.868.2.5.3.0.6
A alarm indication signal event is sent when there is a warning or alarm on TDM port.
Status: current Access: read-write
NOTIFICATION-TYPE    

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor