HUAWEI-VECTOR-MIB

File: HUAWEI-VECTOR-MIB.mib (48202 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC HUAWEI-MIB
IF-MIB HUAWEI-DEVICE-MIB HUAWEI-VDSL2-LINE-TC-MIB
HUAWEI-XDSL-COMMON-MIB

Imported symbols

enterprises Integer32 Unsigned32
Gauge32 OBJECT-TYPE MODULE-IDENTITY
OBJECT-IDENTITY NOTIFICATION-TYPE RowStatus
TruthValue TEXTUAL-CONVENTION huaweiUtility
ifIndex hwFrameIndex hwSlotIndex
hwPortIndex hwConfigChangeIP Vdsl2Direction
hwXdslRequestID hwXdslPortFrequentRetrainControlTimes

Defined Types

HwVectoringGroupEntry  
SEQUENCE    
  hwVectoringGroupIndex Unsigned32
  hwVectoringGroupNotReqBandsUs OCTET STRING
  hwVectoringGroupNotReqBandsDs OCTET STRING
  hwVectoringGroupLinkList OCTET STRING
  hwVectoringGroupRowStatus RowStatus
  hwVectoringGroupProtectionOfNotReqBandsDs INTEGER
  hwVectoringGroupProtectionOfNotReqBandsUs INTEGER

HwVectoringConfProfEntry  
SEQUENCE    
  hwVectoringProfName OCTET STRING
  hwVectoringEnableUs INTEGER
  hwVectoringEnableDs INTEGER
  hwVectoringProfRowStatus RowStatus

HwVectoringPortEntry  
SEQUENCE    
  hwVectoringLinkCfgProf OCTET STRING
  hwVectoringLinkBelongedVceId Unsigned32
  hwVectoringLinkVcePortIndex Unsigned32
  hwVectoringLinkBandPlanCompatible INTEGER
  hwVectoringLinkCPEType INTEGER

HwVectoringAutoGroupingEntry  
SEQUENCE    
  hwVectoringAutoGroupingGroupIndex Unsigned32
  hwVectoringAutoGroupingGroupLinkList OCTET STRING

HwVectoringCrosstalkCouplingMatrixEntry  
SEQUENCE    
  hwVectoringCrosstalkCouplingMatrixDirection Vdsl2Direction
  hwVectoringCrosstalkCoupingMatrixOperType INTEGER
  hwVectoringCrosstalkCoupingMatrixOperResult INTEGER
  hwVectoringCrosstalkCouplingMatrixPortIfindexList OCTET STRING
  hwVectoringCrosstalkCouplingMatrixAverageMagnitudeList OCTET STRING
  hwVectoringCrosstalkCouplingMatrixCancellationStatusList OCTET STRING

HwVectoringBoardVectoringStateEntry  
SEQUENCE    
  hwVectoringVpVectoringInterfaceState INTEGER
  hwVectoringVdslVectoringInterfaceState INTEGER
  hwVectoringVdslVectoringSyncState INTEGER

Defined Values

hwVectoringMIB 1.3.6.1.4.1.2011.6.171
This mib is used for defining huawei's vectoring management MIB objects. The MIB is used for vectoring, vectoring is a transmission method that employs the coordination of line signals for reduction of crosstalk levels and improvement of performance.
MODULE-IDENTITY    

hwVectoringGlobalConfig 1.3.6.1.4.1.2011.6.171.1
OBJECT IDENTIFIER    

hwVectoringSwitch 1.3.6.1.4.1.2011.6.171.1.1
Enable/Disable the global vectoring configuration. Default values:disable. Options: 1. enable(1) - Enables the global vectoring configuration 2. disable(2) - Disables the global vectoring configuration
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hwVectoringLegacyCpeActivatePolicy 1.3.6.1.4.1.2011.6.171.1.2
Vectoring legacy cpe activate policy. Default values:limit. Options: 1. no-limit(1) - The legacy cpe is allowed to activated in G.993.2 operation mode 2. block(2) - The legacy cpe is not allowed to activated in G.993.2 operation mode 3. limit(3) - The legacy cpe is allowed to activated in G.993.2 operation mode, with PSD auto shaped to eliminate the self-FEXT to vectoring lines 4. forceFriendlyDsLimitUs(4) - Force friendly is used in the downstream direction, and PSD automatic shaping is used in the upstream direction 5. forceFriendlyDsNoLimitUs(5) - Force friendly is used in the downstream direction, and no restriction is set for the upstream direction
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER no-limit(1), block(2), limit(3), forceFriendlyDsLimitUs(4), forceFriendlyDsNoLimitUs(5)  

hwVectoringBandplanType 1.3.6.1.4.1.2011.6.171.1.3
Vectoring global frequency plan types. Default values:bandplan998ade. Options: 1. bandplanAnnexa(1) - The frequency plan types for the vectoring feature is Annex A 2. bandplanAnnexc(2) - The frequency plan types for the vectoring feature is Annex C 3. bandplan997e(3) - The frequency plan types for the vectoring feature is 997E 4. bandplan998ade(4) - The frequency plan types for the vectoring feature is 998ADE 5. bandplan998e(5) - The frequency plan types for the vectoring feature is 998E 6. bandplanHPE(6) - The frequency plan types for the vectoring feature is HPE
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER bandplanAnnexa(1), bandplanAnnexc(2), bandplan997e(3), bandplan998ade(4), bandplan998e(5), bandplanHPE(6)  

hwVectoringUs0Type 1.3.6.1.4.1.2011.6.171.1.4
Vectoring us0 type. Default values:us0TypeA. Options: 1. us0TypeA(1) - US0 type is US0-type A 2. us0TypeB(2) - US0 type is US0-type B 3. us0TypeM(3) - US0 type is US0-type M 4. us0TypeN(4) - US0 type is US0-type N/A 5. invalidValue(-1) - US0 type return -1 when vectoring frequency plan types is Annex A/Annex C
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER us0TypeA(1), us0TypeB(2), us0TypeM(3), us0TypeN(4), invalidValue(-1)  

hwVectoringAnnexALimitMask 1.3.6.1.4.1.2011.6.171.1.5
AnnexA limit mask. Options: 1. d32(1) - AnnexA limit mask is D-32 2. d48(2) - AnnexA limit mask is D-48 3. d64(3) - AnnexA limit mask is D-64 4. d128(4) - AnnexA limit mask is D-128 5. invalidValue(-1) - AnnexA limit mask return -1 when vectoring frequency plan types is not Annex A
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER d32(1), d48(2), d64(3), d128(4), invalidValue(-1)  

hwVectoringLegacyCpeReservedBand 1.3.6.1.4.1.2011.6.171.1.6
This object is used to set the reserved band of a legacy CPE. This object takes effect when hwVectoringLegacyCpeActivatePolicy is set to limit. Range of the subcarrier IDs: 0-6956. Two subcarriers are separated by a comma (,). The format is: start subcarrier ID-end subcarrier ID. The start subcarrier ID cannot be greater than the end subcarrier ID. Only eight reserved band is supported, for example, 880-900,1000-1100. The settings of hwVectoringLegacyCpeReservedBand and hwVectoringLegacyCpeToneBlackoutBand cannot overlap with each other.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..79)  

hwVectoringLegacyCpeToneBlackoutBand 1.3.6.1.4.1.2011.6.171.1.7
This object is used to set the blackout band of a legacy CPE. This object takes effect when hwVectoringLegacyCpeActivatePolicy is set to limit. Range of the subcarrier IDs: 0-6956. Two subcarriers are separated by a comma (,). The format is: start subcarrier ID-end subcarrier ID. The start subcarrier ID cannot be greater than the end subcarrier ID. Only eight tone blackout band is supported, for example, 1300-1320,1400-1500. The settings of hwVectoringLegacyCpeReservedBand and hwVectoringLegacyCpeToneBlackoutBand cannot overlap with each other.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..79)  

hwVectoringGroupTable 1.3.6.1.4.1.2011.6.171.2
The table hwVectoringGroupTable contains the vectoring group configuration. The index of this table is hwVectoringGroupIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwVectoringGroupEntry

hwVectoringGroupEntry 1.3.6.1.4.1.2011.6.171.2.1
The table hwVectoringGroupTable contains the vectoring group configuration. The index of this entry is hwVectoringGroupIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwVectoringGroupEntry  

hwVectoringGroupIndex 1.3.6.1.4.1.2011.6.171.2.1.1
This object identifies a row in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..96  

hwVectoringGroupNotReqBandsUs 1.3.6.1.4.1.2011.6.171.2.1.2
This configuration parameter shall be an array of pairs of sub-carrier indices for uptream . Each pair represents the start and stop sub-carrier index of a frequency band in which FEXT cancellation is not required. Up to 8 frequency bands may be configured. for example :880-900,1000-1020
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..79)  

hwVectoringGroupNotReqBandsDs 1.3.6.1.4.1.2011.6.171.2.1.3
This configuration parameter shall be an array of pairs of sub-carrier indices for downstream . Each pair represents the start and stop sub-carrier index of a frequency band in which FEXT cancellation is not required. Up to 8 frequency bands may be configured. for example :1300-1320,1400-1450
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..79)  


hwVectoringGroupRowStatus 1.3.6.1.4.1.2011.6.171.2.1.5
This object is used to create a new row or delete an existing row in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hwVectoringGroupProtectionOfNotReqBandsDs 1.3.6.1.4.1.2011.6.171.2.1.6
This object enable/disable the protection of vectoring lines downstream. Options: 1. enable(1)- The protection of vectoring lines downstream is enabled 2. disable(2) - The protection of vectoring lines downstream is disabled
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hwVectoringGroupProtectionOfNotReqBandsUs 1.3.6.1.4.1.2011.6.171.2.1.7
This object enable/disable the protection of vectoring lines upstream. Options: 1. enable(1)- The protection of vectoring lines upstream is enabled 2. disable(2) - The protection of vectoring lines upstream is disabled
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hwVectoringConfProfTable 1.3.6.1.4.1.2011.6.171.3
The table hwVectoringConfProfTable contains the vectoring profile configuration. A default profile with an index of 'DEFVAL' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document. The index of this table is hwVectoringProfName.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwVectoringConfProfEntry

hwVectoringConfProfEntry 1.3.6.1.4.1.2011.6.171.3.1
The table hwVectoringConfProfTable contains the vectoring profile configuration. A default profile with an index of 'DEFVAL' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document. The index of this entry is hwVectoringProfName.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwVectoringConfProfEntry  

hwVectoringProfName 1.3.6.1.4.1.2011.6.171.3.1.1
This object identifies a row in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  OCTET STRING Size(1..32)  

hwVectoringEnableUs 1.3.6.1.4.1.2011.6.171.3.1.2
Enable/Disable FEXT cancellation control upstream. Default values: enable. Options: 1. enable(1) - Enable FEXT cancellation in the upstream direction from all the other vectoring lines into the line in the vectoring group 2. disable(2) - Disable FEXT cancellation in the upstream direction from all the other vectoring lines into the line in the vectoring group.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hwVectoringEnableDs 1.3.6.1.4.1.2011.6.171.3.1.3
Enable/Disable FEXT cancellation control downstream. Default values: enable. Options: 1. enable(1) - Enable FEXT cancellation in the downstream direction from all the other vectoring lines into the line in the vectoring group 2. disable(2) - Disable FEXT cancellation in the downstream direction from all the other vectoring lines into the line in the vectoring group
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hwVectoringProfRowStatus 1.3.6.1.4.1.2011.6.171.3.1.4
This object is used to create a new row or delete an existing row in this table. Before a profile can be deleted, it must be not referenced from all VDSL ports.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hwVectoringPortTable 1.3.6.1.4.1.2011.6.171.4
The table hwVectoringPortTable contains port configuration about vectoring. The index of this table is ifIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwVectoringPortEntry

hwVectoringPortEntry 1.3.6.1.4.1.2011.6.171.4.1
The table hwVectoringPortTable contains port configuration about vectoring. The index of this entry is ifIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwVectoringPortEntry  

hwVectoringLinkCfgProf 1.3.6.1.4.1.2011.6.171.4.1.1
This object configures the vectoring link profile name.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

hwVectoringLinkBelongedVceId 1.3.6.1.4.1.2011.6.171.4.1.2
The VCE ID uniquely identifies the VCE that manages and controls the vectored group to which the line belongs. It consists of one octet and valid ranges are from 1 to 96. The special value 0 means the line is not in a vectored group.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..96  

hwVectoringLinkVcePortIndex 1.3.6.1.4.1.2011.6.171.4.1.3
The VCE port index is the physical index that uniquely identifies the VCE port to which the line is connected. It is an integer from 1 to the maximum number of lines supported by the VCE. The special value 0 means the VCE port index is not valid
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..512  

hwVectoringLinkBandPlanCompatible 1.3.6.1.4.1.2011.6.171.4.1.4
Options: 1. compatible(1) - The vectoring line configured band plan is compatible with the vectoring band configuration 2. incompatible(2) - The vectoring line configured band plan is not compatible with the vectoring band configuration
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER compatible(1), incompatible(2)  

hwVectoringLinkCPEType 1.3.6.1.4.1.2011.6.171.4.1.5
Options: 1. vectoring(1) - The CPE type is vectoring 2. fullFriendly(2) - The CPE type is vectoring full friendly 3. friendlyDs(3) - The CPE type is vectoring friendly ds 4. legacyVdsl2(4) - The CPE type is vdsl2 5. adsl(5) - The CPE type is adsl/2/2+ 6. unknown(6) - The CPE type is unknown
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER vectoring(1), fullFriendly(2), friendlyDs(3), legacyVdsl2(4), adsl(5), unknown(6)  

hwVectoringAutoGroupingTable 1.3.6.1.4.1.2011.6.171.5
The table hwVectoringAutoGroupingTable contains the vectoring auto group result. The indexes of this table are hwVectoringGroupIndex and hwVectoringAutoGroupingGroupIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwVectoringAutoGroupingEntry

hwVectoringAutoGroupingEntry 1.3.6.1.4.1.2011.6.171.5.1
The table hwVectoringAutoGroupingTable contains the vectoring auto group result. The indexes of this entry are hwVectoringGroupIndex and hwVectoringAutoGroupingGroupIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwVectoringAutoGroupingEntry  

hwVectoringAutoGroupingGroupIndex 1.3.6.1.4.1.2011.6.171.5.1.1
This object identifies auto group index.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..96  


hwVectoringCrosstalkCouplingMatrixTable 1.3.6.1.4.1.2011.6.171.6
The table hwVectoringCrosstalkCouplingMatrixTable contains information of vectoring crosstalk coupling matrix about a port in a vectoring group. The indexes of this table are ifIndex and hwVectoringCrosstalkCouplingMatrixDirection.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwVectoringCrosstalkCouplingMatrixEntry

hwVectoringCrosstalkCouplingMatrixEntry 1.3.6.1.4.1.2011.6.171.6.1
The table hwVectoringCrosstalkCouplingMatrixTable contains information of vectoring crosstalk coupling matrix about a port in a vectoring group. The indexes of this entry are ifIndex and hwVectoringCrosstalkCouplingMatrixDirection.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwVectoringCrosstalkCouplingMatrixEntry  

hwVectoringCrosstalkCouplingMatrixDirection 1.3.6.1.4.1.2011.6.171.6.1.1
The direction of the vectoring crosstalk coupling matrix either upstream or downstream.
Status: current Access: not-accessible
OBJECT-TYPE    
  Vdsl2Direction  

hwVectoringCrosstalkCoupingMatrixOperType 1.3.6.1.4.1.2011.6.171.6.1.2
This object is used to start the vectoring crosstalk coupling matrix. Options: 1. start(1) - start the vectoring crosstalk coupling matrix 2. stop(2) - stop the vectoring crosstalk coupling matrix
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER start(1), stop(2)  

hwVectoringCrosstalkCoupingMatrixOperResult 1.3.6.1.4.1.2011.6.171.6.1.3
This object identifies the crosstalk coupling matrix operation result. Options: 1. normal(1) - The crosstalk coupling matrix operation result is normal. 2. fail(2) - The crosstalk coupling matrix operation result is fail.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER normal(1), fail(2)  

hwVectoringCrosstalkCouplingMatrixPortIfindexList 1.3.6.1.4.1.2011.6.171.6.1.4
Ifindex list of port that effect another port in the same vectoring group. This is a string of 4 bytes of values indicates the port ifindex.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..2048)  

hwVectoringCrosstalkCouplingMatrixAverageMagnitudeList 1.3.6.1.4.1.2011.6.171.6.1.5
In this matrix must be seen all vectoring subscribers with disturberline. This is a string of 4 bytes of values indicates the port average magnitude. The units is 0.1 dBm/Hz.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..2048)  

hwVectoringCrosstalkCouplingMatrixCancellationStatusList 1.3.6.1.4.1.2011.6.171.6.1.6
This is a string of 1 bytes of values indicates the port crosstalk another. The byte value indicates: 1. yes(1) - counteract 2. no(2) - not counteract 3. invalidValue(-1) - invalid value
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..512)  

hwVectoringBoardVectoringStateTable 1.3.6.1.4.1.2011.6.171.7
The table hwVectoringBoardVectoringStateTable contains the vectoring current running information. The indexes of this table are hwFrameIndex and hwSlotIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwVectoringBoardVectoringStateEntry

hwVectoringBoardVectoringStateEntry 1.3.6.1.4.1.2011.6.171.7.1
The table hwVectoringBoardVectoringStateTable contains the vectoring current running information. The indexes of this entry are hwFrameIndex and hwSlotIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwVectoringBoardVectoringStateEntry  

hwVectoringVpVectoringInterfaceState 1.3.6.1.4.1.2011.6.171.7.1.1
The object indicates VCE vectoring interface state. Options: 1. down(1) - vectoring interface state is abnormal 2. up(2) - vectoring interface state is normal 3. invalidValue(-1) - invalid value
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER down(1), up(2), invalidValue(-1)  

hwVectoringVdslVectoringInterfaceState 1.3.6.1.4.1.2011.6.171.7.1.2
The object indicates VDSL vectoring interface state. Options: 1. down(1) - vectoring interface state is abnormal 2. up(2) - vectoring interface state is normal 3. invalidValue(-1) - invalid value
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER down(1), up(2), invalidValue(-1)  

hwVectoringVdslVectoringSyncState 1.3.6.1.4.1.2011.6.171.7.1.3
The object indicates Sync state between VCE and VDSL vectoring interface. Options: 1. noSync(1) - communication between VCE and VDSL is abnormal 2. sync(2) - communication between VCE and VDSL is normal 3. invalidValue(-1) - invalid value
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER noSync(1), sync(2), invalidValue(-1)  

hwVectoringTraps 1.3.6.1.4.1.2011.6.171.8
OBJECT IDENTIFIER    

hwVectoringAlarmTraps 1.3.6.1.4.1.2011.6.171.8.1
OBJECT IDENTIFIER    

hwVectoringAlarmTrapsPrefix 1.3.6.1.4.1.2011.6.171.8.1.1
OBJECT IDENTIFIER    

hwVectoringCommonTraps 1.3.6.1.4.1.2011.6.171.8.2
OBJECT IDENTIFIER    

hwVectoringCommonTrapsPrefix 1.3.6.1.4.1.2011.6.171.8.2.1
OBJECT IDENTIFIER    

hwVectoringFaultAlarmTrap 1.3.6.1.4.1.2011.6.171.8.1.1.1
This notification indicates that the vectoring service on the board fails.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwVectoringRecoveryAlarmTrap 1.3.6.1.4.1.2011.6.171.8.1.1.2
This notification indicates that the vectoring service on the board recovers.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwVectoringVictCoefAbnormalVariationAlarmTrap 1.3.6.1.4.1.2011.6.171.8.1.1.3
This notification indicates that the port receives abnormal crosstalk from other ports.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwVectoringDistCoefAbnormalVariationAlarmTrap 1.3.6.1.4.1.2011.6.171.8.1.1.4
This notification indicates that the port causes abnormal crosstalk to other ports.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwVectoringReceivedESAbnormalAlarmTrap 1.3.6.1.4.1.2011.6.171.8.1.1.5
This notification indicates that the port receives abnormal error sample messages.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwvdsl2LegacyCpeActivatedAlarmTrap 1.3.6.1.4.1.2011.6.171.8.1.1.6
This notification indicates that the port is activated in none-vectoring mode.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwvdsl2FrequentlyRetrainTimesReachThresholdAlarmTrap 1.3.6.1.4.1.2011.6.171.8.1.1.7
This notification indicates that the port frequently retrain times in 15 minutes reach the threshold.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwVectoringReceivedESRecoverAlarmTrap 1.3.6.1.4.1.2011.6.171.8.1.1.8
This notification indicates that the port error sample feedback recovers.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwVectoringPSConfigAbnormalAlarmTrap 1.3.6.1.4.1.2011.6.171.8.1.1.9
This notification indicates that the port receives abnormal pilot Sequence messages.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwVectoringPSConfigRecoverAlarmTrap 1.3.6.1.4.1.2011.6.171.8.1.1.10
This notification indicates that the port pilot sequence recovers.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwVectoringGlobalConfigChangeTrap 1.3.6.1.4.1.2011.6.171.8.2.1.1
This notification indicates that the vectoring global configuration is changed.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwVectoringCrosstalkCoupingMatrixOperResultTrap 1.3.6.1.4.1.2011.6.171.8.2.1.2
This notification indicates that the vectoring crosstalk coupling matrix calculation result.
Status: current Access: read-only
NOTIFICATION-TYPE    

hwVectoringFastJoinConfig 1.3.6.1.4.1.2011.6.171.9
OBJECT IDENTIFIER    

hwVectoringGainPhase 1.3.6.1.4.1.2011.6.171.9.1
This object is used to set the mode for obtaining the vectoring gain during port activation. Default values:atInit. Options: 1. atInit(1) - The vectoring gain is obtained during port activation except board startup 2. trigger(2) - The vectoring gain is obtained in some condition 3. duringShowtime(3) - The port is activated and then the vectoring gain is obtained during tracking
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER atInit(1), trigger(2), duringShowtime(3)  

hwVectoringTriggerAfterBoardReset 1.3.6.1.4.1.2011.6.171.9.2
The vectoring gain is not obtained during port activation in board reset, but obtained during tracking in SRA. Default values:enable. Options: 1. enable(1) - Enables the vectoring gain achieved in showtime after board reset 2. disable(2) - Disables the vectoring gain achieved in showtime after board reset 3. invalidValue(-1) - invalid value
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2), invalidValue(-1)  

hwVectoringTriggerDuringBulkNum 1.3.6.1.4.1.2011.6.171.9.3
The vectoring gain achieved in showtime when the number of ports join in at a time exceeds the configured bulk init number. It ranges from 2 to 256. The invalid value is 4294967295. Default values:64.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

hwVectoringJoinMaxWaitTime 1.3.6.1.4.1.2011.6.171.9.4
This object is used to set the total time for a joined port to wait for other ports in the batch to join. Default values:15.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..60  

hwVectoringJoinGapWaitTime 1.3.6.1.4.1.2011.6.171.9.5
This object is used to set the interval for a joined port to wait for a single port in the batch to join. Default values:5.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..60  

hwVectoringTrackingPeriod 1.3.6.1.4.1.2011.6.171.9.6
Vectoring tracking period. Default values:30.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..240  

hwVectoringHistoryCoefficient 1.3.6.1.4.1.2011.6.171.9.7
This object is used to set whether to use a historical coefficient. Default values:both. Options: 1. disable(1) - Indicates that a historical coefficient is not used 2. upstream(2) - Indicates that a historical coefficient is used in upstream direction 3. downstream(3) - Indicates that a historical coefficient is used in downstream direction 4. both(4) - Indicates that a historical coefficient is used
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), upstream(2), downstream(3), both(4)  

hwVectoringTrapsVbOids 1.3.6.1.4.1.2011.6.171.10
OBJECT IDENTIFIER    

hwVectoringPortFrequentRetrainTimes 1.3.6.1.4.1.2011.6.171.10.1
The times that Xdsl port frequent retrain in 15 minutes.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Unsigned32  

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor