HUAWEI-XDSL-COMMON-MIB

File: HUAWEI-XDSL-COMMON-MIB.mib (28970 bytes)

Imported modules

IF-MIB RFC1213-MIB HUAWEI-DEVICE-MIB
SNMPv2-SMI SNMPv2-TC HUAWEI-MIB
HUAWEI-TC-MIB

Imported symbols

ifIndex ifType hwFrameIndex
hwSlotIndex hwSubslotIndex hwPortIndex
hwConfigChangeIP Integer32 Unsigned32
Gauge32 Counter32 OBJECT-TYPE
NOTIFICATION-TYPE MODULE-IDENTITY RowStatus
PhysAddress DateAndTime TEXTUAL-CONVENTION
huaweiUtility hwAlarmId hwAlarmTime
hwAlarmSn hwCauseId hwTrapType

Defined Types

HwXdslLineEntry  
SEQUENCE    
  hwAllChActDataRateDs Unsigned32
  hwAllChActDataRateUs Unsigned32

HwXdslPortFrequentRetrainControlEntry  
SEQUENCE    
  hwXdslPortFrequentRetrainControlTimes Unsigned32
  hwXdslPortFrequentRetrainControlPolicy INTEGER
  hwXdslPortFrequentRetrainControlPostponedTime Unsigned32

Defined Values

hwXdslCommon 1.3.6.1.4.1.2011.6.148
This MIB is used for defining Huawei's XDSL common management MIB objects, which provides XDSL management NMS interfaces.
MODULE-IDENTITY    

hwXdslCommonMib 1.3.6.1.4.1.2011.6.148.1
OBJECT IDENTIFIER    

hwXdslAutoDeleteProfUnused 1.3.6.1.4.1.2011.6.148.1.1
OBJECT IDENTIFIER    

hwXdslAttndrConfig 1.3.6.1.4.1.2011.6.148.1.4
OBJECT IDENTIFIER    

hwXdslADSL1INPAdaptionConfig 1.3.6.1.4.1.2011.6.148.1.5
OBJECT IDENTIFIER    

hwXdslTrapsVbOids 1.3.6.1.4.1.2011.6.148.2
OBJECT IDENTIFIER    

hwXdslTraps 1.3.6.1.4.1.2011.6.148.3
OBJECT IDENTIFIER    

hwXdslCommonTraps 1.3.6.1.4.1.2011.6.148.3.1
OBJECT IDENTIFIER    

hwXdslCommonTrapsPrefix 1.3.6.1.4.1.2011.6.148.3.1.0
OBJECT IDENTIFIER    

hwXdslAlarmTraps 1.3.6.1.4.1.2011.6.148.3.2
OBJECT IDENTIFIER    

hwXdslAlarmTrapsPrefix 1.3.6.1.4.1.2011.6.148.3.2.0
OBJECT IDENTIFIER    

hwXdslAutoDeleteProfUnusedProfType 1.3.6.1.4.1.2011.6.148.1.1.1
The profile type of deleting unused XDSL profile. Options: 1. vdsl2LineConfTemplate(1) - Vdsl line template 2. vdsl2LineConfProf(2) - Vdsl line profile 3. vdsl2ChConfProfile(3) - Vdsl channel profile 4. vdsl2LineAlarmConfTemplate(4) - Vdsl line alarm template 5. vdsl2LineAlarmConfProfile(5) - Vdsl line alarm profile 6. vdsl2ChAlarmConfProfile(6) - Vdsl channel alarm profile 7. vdsl2ServProf(7) - Vdsl service profile (TI mode) 8. vdsl2SpectrumProf(8) - Vdsl spectrum profile (TI mode) 9. vdsl2DpboProf(9) - Vdsl DPBO profile (TI mode) 10. vdsl2UpboProf(10) - Vdsl UPBO profile (TI mode) 11. vdsl2NoiseMarginProf(11) - Vdsl noise-margin profile (TI mode) 12. vdsl2DelayInpProf(12) - Vdsl delay-inp profile (TI mode) 13. vopDataRateConfProf(13) - Xdsl data rate profile (TR165 mode) 14. vopLineSpectrumConfProf(14) - Xdsl line spectrum profile (TR165 mode) 15. vopUPBOConfProf(15) - Xdsl UPBO profile (TR165 mode) 16. vopDPBOConfProf(16) - Xdsl DPBO profile (TR165 mode) 17. vopRFIConfProf(17) - Xdsl RFI profile (TR165 mode) 18. vopSNRMarginConfProf(18) - Xdsl SNR margin profile (TR165 mode) 19. vopINPDelayConfProf(19) - Xdsl INP delay profile (TR165 mode) 20. vopVirtualNoiseConfProf(20) - Xdsl virtual noise profile (TR165 mode) 21. vopModeSpecificPSDConfProf(21) - Xdsl mode specific PSD profile (TR165 mode) 22. adsl2LineConfTemplate(22) - Adsl line template (RFC4706 mode) 23. adsl2LineConfProf(23) - Adsl line profile (RFC4706 mode) 24. adsl2ChConfProfile(24) - Adsl channel profile (RFC4706 mode) 25. adsl2LineAlarmConfTemplate(25) - Adsl line alarm template (RFC4706 mode) 26. adsl2LineAlarmConfProfile(26) - Adsl line alarm profile (RFC4706 mode) 27. adsl2ChAlarmConfProfile(27) - Adsl channel alarm profile (RFC4706 mode) 28. adslLineConfProfile(28) - Adsl line profile (RFC2662 mode) 29. adslLineAlarmConfProfile(29) - Adsl line alarm profile (RFC2662 mode) 30. adslLineExtConfProfile(30) - Adsl line ext profile (RFC2662 mode) 31. shdslLineConfProfile(31) - Shdsl line profile 32. shdslAlarmConfProfile(32) - Shdsl alarm profile 33. vopINMConfProf(33) - Xdsl INM profile (TR165 mode) 34. invalidValue(-1) - Invalid value
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER vdsl2LineConfTemplate(1), vdsl2LineConfProf(2), vdsl2ChConfProfile(3), vdsl2LineAlarmConfTemplate(4), vdsl2LineAlarmConfProfile(5), vdsl2ChAlarmConfProfile(6), vdsl2ServProf(7), vdsl2SpectrumProf(8), vdsl2DpboProf(9), vdsl2UpboProf(10), vdsl2NoiseMarginProf(11), vdsl2DelayInpProf(12), vopDataRateConfProf(13), vopLineSpectrumConfProf(14), vopUPBOConfProf(15), vopDPBOConfProf(16), vopRFIConfProf(17), vopSNRMarginConfProf(18), vopINPDelayConfProf(19), vopVirtualNoiseConfProf(20), vopModeSpecificPSDConfProf(21), adsl2LineConfTemplate(22), adsl2LineConfProf(23), adsl2ChConfProfile(24), adsl2LineAlarmConfTemplate(25), adsl2LineAlarmConfProfile(26), adsl2ChAlarmConfProfile(27), adslLineConfProfile(28), adslLineAlarmConfProfile(29), adslLineExtConfProfile(30), shdslLineConfProfile(31), shdslAlarmConfProfile(32), vopINMConfProf(33), invalidValue(-1)  

hwXdslAutoDeleteProfUnusedOperType 1.3.6.1.4.1.2011.6.148.1.1.2
The operation type of deleting unused xDSL profile. Options: 1. first(1) - Delete the first unused xDSL profile 2. all(2) - Delete all the unused xDSL profile 3. invalidValue(-1) - Invalid value
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER first(1), all(2), invalidValue(-1)  

hwXdslLineTable 1.3.6.1.4.1.2011.6.148.1.2
The table hwXdslLineTable contains status parameters of xDSL line. The index of this table is ifIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwXdslLineEntry

hwXdslLineEntry 1.3.6.1.4.1.2011.6.148.1.2.1
The table hwXdslLineTable contains status parameters of xDSL line. The index of this entry is ifIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwXdslLineEntry  

hwAllChActDataRateDs 1.3.6.1.4.1.2011.6.148.1.2.1.1
The downstream actual net data rate that the bearer channel is operating at, if in L0 power management state. In L1 or L2 states, it relates to the previous L0 state. This is the sum of net date rates that all bearer channels operating at.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwAllChActDataRateUs 1.3.6.1.4.1.2011.6.148.1.2.1.2
The upstream actual net data rate that the bearer channel is operating at, if in L0 power management state. In L1 or L2 states, it relates to the previous L0 state. This is the sum of net date rates that all bearer channels operating at.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwXdslPortFrequentRetrainControlTable 1.3.6.1.4.1.2011.6.148.1.3
The table hwXdslPortFrequentRetrainControlTable contains information of xDSL port frequent retrain control policy. The index of this table is ifIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwXdslPortFrequentRetrainControlEntry

hwXdslPortFrequentRetrainControlEntry 1.3.6.1.4.1.2011.6.148.1.3.1
The table hwXdslPortFrequentRetrainControlTable contains information of xDSL port frequent retrain control policy. The index of this entry is ifIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwXdslPortFrequentRetrainControlEntry  

hwXdslPortFrequentRetrainControlTimes 1.3.6.1.4.1.2011.6.148.1.3.1.1
The times that xDSL port frequent retrain. The invalid value is 4294967295. If board does not support the operation, the invalid value will be returned.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 3..15 | 4294967295  

hwXdslPortFrequentRetrainControlPolicy 1.3.6.1.4.1.2011.6.148.1.3.1.2
The control policy that xDSL port frequent retrain. Options: 1. lock(1) - The port is not allowed to go online within 15 minutes 2. nolimit(2) - The port can go online without the limitation of control policies 3. postponed(3) - The port can go online after a postponed time when the number of frequent resynchronizations on the port reaches the threshold 4. invalidValue(-1) - Invalid value
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER lock(1), nolimit(2), postponed(3), invalidValue(-1)  

hwXdslPortFrequentRetrainControlPostponedTime 1.3.6.1.4.1.2011.6.148.1.3.1.3
The postponed time when control policy of xDSL port frequent retrain is postponed. The invalid value is 4294967295. If board does not support the operation, the invalid value will be returned.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 5..3600 | 4294967295  

hwXdslAttndrMethod 1.3.6.1.4.1.2011.6.148.1.4.1
This parameter specifies the method to be used for the calculation of the ATTNDR in the downstream and upstream direction. The parameter can take three values 0, 1 and 2. Options: 1. attndrMethod0(0) - The basic Attainable Net Data Rate method 2. attndrMethod1(1) - The improved Attainable Net Data Rate method, If the control parameter attndr_method is set to a value of 1, the VTU-O and VTU-R shall use the impulse noise protection limit INP_min0 with value as indicated in O-TPS. If O-TPS configures for dual bearer channel mode, then the highest INP_MINn over the bearer channels shall be used 1 3. attndrMethod2(2) - The improved Attainable Net Data Rate method, If the control parameter attndr_method is set to a value of 2, the VTU-O and VTU-R shall use an impulse noise protection limit INP_MIN0 = 0
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER attndrMethod0(0), attndrMethod1(1), attndrMethod2(2)  

hwXdslADSL1INPAdaption 1.3.6.1.4.1.2011.6.148.1.5.1
Enable/Disable the global ADSL1 INP Adaption configuration. This object is defaulted disable(2). This configuration will take effect after port manually reactivated or board reset. Options: 1. enable(1) - Enable the ADSL1 INP Adaption configuration 2. disable(2) - Disable the ADSL1 INP Adaption configuration
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hwXdslDynamicCollectResult 1.3.6.1.4.1.2011.6.148.2.1
Dynamic information collecting result. Options: 1. noFail(0) - The dynamic info has been collected successful 2. memFull(1) - The memory used for dynamic info collecting is full 3. otherCause(2) - Other collect failure reason
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER noFail(0), memFull(1), otherCause(2)  

hwXdslDynamicCollectTime 1.3.6.1.4.1.2011.6.148.2.2
Time of the Dynamic information file.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DateAndTime  

hwXdslRequestID 1.3.6.1.4.1.2011.6.148.2.3
Request ID.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

hwXdslSeltCompleteResult 1.3.6.1.4.1.2011.6.148.2.4
Selt test complete result. Options: 1. success(1) - Selt test is successful 2. fail(2) - Failed in selt test
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER success(1), fail(2)  

hwAdslProfIDType 1.3.6.1.4.1.2011.6.148.2.5
Type of the adsl template ID. Options: 1. lineTemplate(1) - Indicates line template ID 2. alarmTemplate(2) - Indicates alarm template ID 3. extProfile(3) - Indicates ext profile ID
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER lineTemplate(1), alarmTemplate(2), extProfile(3)  

hwXdslProfName 1.3.6.1.4.1.2011.6.148.2.6
The name of the XDSL profile.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  OCTET STRING Size(1..32)  

hwXdslPortActualUpRate 1.3.6.1.4.1.2011.6.148.2.7
Xdsl port actual upstream rate.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Unsigned32  

hwXdslPortActualDownRate 1.3.6.1.4.1.2011.6.148.2.8
Xdsl port actual downstream rate.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Unsigned32  

hwXdslDelProfIndex 1.3.6.1.4.1.2011.6.148.2.9
Index of the profile which is deleted. If you delete all the profiles unused, this parameter will be 0xffffffff.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Unsigned32  

hwXdslDelProfName 1.3.6.1.4.1.2011.6.148.2.10
Name of the profile which is deleted. If you delete all the profiles unused, this parameter will be a zero string.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  OCTET STRING Size(0..128)  

hwXdslSeltTestStartResult 1.3.6.1.4.1.2011.6.148.2.11
XDSL selt test start result. Options: 1. normal(1) - This notification indicates that a SELT task has been started successfully 2. failed(2) - This notification indicates that a SELT task failed to be started
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER normal(1), failed(2)  

hwXdslDynamicCollectInfoTrap 1.3.6.1.4.1.2011.6.148.3.1.0.1
XDSL dynamic collect trap. This trap message is generated when XDSL dynamic collected.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

hwXdslSeltCompleteResultTrap 1.3.6.1.4.1.2011.6.148.3.1.0.2
Selt test complete result trap. This trap message is generated when selt test completed.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

hwAdslProfIDChangeTrap 1.3.6.1.4.1.2011.6.148.3.1.0.3
Adsl profile ID change trap. This trap message is generated when adsl profile ID changed.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

hwXdslProfDeleteTrap 1.3.6.1.4.1.2011.6.148.3.1.0.4
This trap message is generated when Xdsl unused profile trap deleted.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

hwXdslSeltStartResultTrap 1.3.6.1.4.1.2011.6.148.3.1.0.5
XDSL selt test start trap. This notification indicates trap when xDSL selt test start.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

hwXdslAutoDeactivateLackLicensesAlarmTrap 1.3.6.1.4.1.2011.6.148.3.2.0.1
This trap message is generated when some xDSL ports or all the xDSL ports are automatically deactivated due to lack of licenses.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

hwXdslPortActRateLowerThresholdAlarmTrap 1.3.6.1.4.1.2011.6.148.3.2.0.2
This trap message is generated when the activation rate of the xDSL line is lower than the threshold.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor