HM2-DIAGNOSTIC-MIB

File: HM2-DIAGNOSTIC-MIB.mib (79749 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC IF-MIB
HM2-TC-MIB HM2-PWRMGMT-MIB HM2-DEVMGMT-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE NOTIFICATION-TYPE
OBJECT-IDENTITY Integer32 Unsigned32
TEXTUAL-CONVENTION TruthValue ifIndex
hm2ConfigurationMibs HmEnabledStatus HmTimeSeconds1970
hm2PSID hm2IfacePhysIndex

Defined Types

Hm2LedType  
Types of LEDs available
TEXTUAL-CONVENTION    
  INTEGER power(1), status(2), rm(3), envm(4), i1(5), i2(6)  

Hm2LedStatus  
Status of LEDs available
TEXTUAL-CONVENTION    
  INTEGER off(1), greenSolid(2), greenBlink1(3), greenBlink3(4), greenBlink4(5), greenBlink5(6), greenBlink5i(7), yellowSolid(8), yellowBlink1(9), yellowBlink3(10), yellowBlink4(11), yellowBlink5(12), redSolid(13), redBlink1(14), redBlink3(15), redBlink4(16), redBlink5(17)  

Hm2DiagSelftestActionEntry  
SEQUENCE    
  hm2DiagSelftestActionCause INTEGER
  hm2DiagSelftestAction INTEGER

Hm2SigConCommonEntry  
SEQUENCE    
  hm2SigConID Integer32
  hm2SigConTrapEnable HmEnabledStatus
  hm2SigConTrapCause INTEGER
  hm2SigConTrapCauseIndex Integer32
  hm2SigConMode INTEGER
  hm2SigConOperState INTEGER
  hm2SigConOperTimeStamp HmTimeSeconds1970
  hm2SigConManualActivate INTEGER
  hm2SigConSenseLinkFailure HmEnabledStatus
  hm2SigConSenseTemperature HmEnabledStatus
  hm2SigConSenseFan HmEnabledStatus
  hm2SigConSenseModuleRemoval HmEnabledStatus
  hm2SigConSenseExtNvmRemoval HmEnabledStatus
  hm2SigConSenseExtNvmNotInSync HmEnabledStatus
  hm2SigConSenseRingRedundancy HmEnabledStatus

Hm2SigConPSEntry  
SEQUENCE    
  hm2SigConSensePSState HmEnabledStatus

Hm2SigConInterfaceEntry  
SEQUENCE    
  hm2SigConSenseIfLinkAlarm HmEnabledStatus

Hm2SigConModuleEntry  
SEQUENCE    
  hm2SigConModID Integer32
  hm2SigConSenseModule HmEnabledStatus

Hm2SigConStatusEntry  
SEQUENCE    
  hm2SigConStatusIndex Integer32
  hm2SigConStatusTimeStamp HmTimeSeconds1970
  hm2SigConStatusTrapCause INTEGER
  hm2SigConStatusTrapCauseIndex Integer32

Hm2DevMonCommonEntry  
SEQUENCE    
  hm2DevMonID Integer32
  hm2DevMonTrapEnable HmEnabledStatus
  hm2DevMonTrapCause INTEGER
  hm2DevMonTrapCauseIndex Integer32
  hm2DevMonOperState INTEGER
  hm2DevMonOperTimeStamp HmTimeSeconds1970
  hm2DevMonSenseLinkFailure HmEnabledStatus
  hm2DevMonSenseTemperature HmEnabledStatus
  hm2DevMonSenseFan HmEnabledStatus
  hm2DevMonSenseModuleRemoval HmEnabledStatus
  hm2DevMonSenseExtNvmRemoval HmEnabledStatus
  hm2DevMonSenseExtNvmNotInSync HmEnabledStatus
  hm2DevMonSenseRingRedundancy HmEnabledStatus

Hm2DevMonPSEntry  
SEQUENCE    
  hm2DevMonSensePSState HmEnabledStatus

Hm2DevMonInterfaceEntry  
SEQUENCE    
  hm2DevMonSenseIfLinkAlarm HmEnabledStatus

Hm2DevMonModuleEntry  
SEQUENCE    
  hm2DevMonModID Integer32
  hm2DevMonSenseModule HmEnabledStatus

Hm2DevMonStatusEntry  
SEQUENCE    
  hm2DevMonStatusIndex Integer32
  hm2DevMonStatusTimeStamp HmTimeSeconds1970
  hm2DevMonStatusTrapCause INTEGER
  hm2DevMonStatusTrapCauseIndex Integer32

Hm2DevSecInterfaceEntry  
SEQUENCE    
  hm2DevSecSenseIfNoLink HmEnabledStatus

Hm2DevSecStatusEntry  
SEQUENCE    
  hm2DevSecStatusIndex Integer32
  hm2DevSecStatusTimeStamp HmTimeSeconds1970
  hm2DevSecStatusTrapCause INTEGER
  hm2DevSecStatusTrapCauseIndex Integer32

Hm2LedGlobalEntry  
SEQUENCE    
  hm2LedGlobalLedType Hm2LedType
  hm2LedGlobalStatus Hm2LedStatus

Hm2LedPortEntry  
SEQUENCE    
  hm2LedPortStatus Hm2LedStatus
  hm2LedPortPoeStatus Hm2LedStatus
  hm2LedPortSignaling HmEnabledStatus

Hm2DiagIfaceUtilizationEntry  
SEQUENCE    
  hm2DiagIfaceUtilization Integer32
  hm2DiagIfaceUtilizationControlInterval Integer32
  hm2DiagIfaceUtilizationAlarmLowerThreshold Integer32
  hm2DiagIfaceUtilizationAlarmUpperThreshold Integer32
  hm2DiagIfaceUtilizationAlarmCondition TruthValue

Hm2DiagCableTesterCableEntry  
SEQUENCE    
  hm2DiagCableTesterCablePair Integer32
  hm2DiagCableTesterCableStatus INTEGER
  hm2DiagCableTesterCableMinimumLength Unsigned32
  hm2DiagCableTesterCableMaximumLength Unsigned32
  hm2DiagCableTesterCableFailureLocation Unsigned32

Hm2PortMonitorIntfEntry  
SEQUENCE    
  hm2PortMonitorIntfReset TruthValue
  hm2PortMonitorIntfAction INTEGER

Hm2PortMonitorConditionIntfEntry  
SEQUENCE    
  hm2PortMonitorConditionField BITS
  hm2PortMonitorConditionLinkFlapMode TruthValue
  hm2PortMonitorConditionCrcFragmentsMode TruthValue
  hm2PortMonitorConditionDuplexMismatchDetectionMode TruthValue
  hm2PortMonitorConditionOverloadDetectionMode TruthValue
  hm2PortMonitorConditionSpeedDuplexMode TruthValue

Hm2PortMonitorConditionLinkFlapIntfEntry  
SEQUENCE    
  hm2PortMonitorConditionLinkFlapInterval Integer32
  hm2PortMonitorConditionLinkFlapCount Integer32
  hm2PortMonitorConditionLinkFlapCountInterval Integer32
  hm2PortMonitorConditionLinkFlapCountTotal Integer32

Hm2PortMonitorConditionCrcFragmentsIntfEntry  
SEQUENCE    
  hm2PortMonitorConditionCrcFragmentsInterval Integer32
  hm2PortMonitorConditionCrcFragmentsCount Integer32
  hm2PortMonitorConditionCrcFragmentsCountInterval Integer32
  hm2PortMonitorConditionCrcFragmentsCountTotal Integer32

Hm2PortMonitorConditionOvldDetIntfEntry  
SEQUENCE    
  hm2PortMonitorConditionOvldDetTrfcType INTEGER
  hm2PortMonitorConditionOvldDetTholdType INTEGER
  hm2PortMonitorConditionOvldDetLwrTholdVal Integer32
  hm2PortMonitorConditionOvldDetUprTholdVal Integer32
  hm2PortMonitorConditionOvldDetIntvl Integer32
  hm2PortMonitorConditionOvldDetPkgCntAll Integer32
  hm2PortMonitorConditionOvldDetPkgCntBC Integer32
  hm2PortMonitorConditionOvldDetPkgCntMC Integer32
  hm2PortMonitorConditionOvldDetPkgCntKbit Integer32

Hm2PortMonitorConditionSpeedDuplexEntry  
SEQUENCE    
  hm2PortMonitorConditionSpeedDuplexValue BITS

Defined Values

hm2DiagnosticMib 1.3.6.1.4.1.248.11.22
Hirschmann Diagnostic MIB. Copyright (C) 2012. All Rights Reserved.
MODULE-IDENTITY    

hm2DiagnosticMibNotifications 1.3.6.1.4.1.248.11.22.0
OBJECT IDENTIFIER    

hm2DiagnosticMibObjects 1.3.6.1.4.1.248.11.22.1
OBJECT IDENTIFIER    

hm2DiagnosticSNMPExtensionGroup 1.3.6.1.4.1.248.11.22.3
OBJECT IDENTIFIER    

hm2DiagSelftestGroup 1.3.6.1.4.1.248.11.22.1.1
OBJECT IDENTIFIER    

hm2DiagBootGroup 1.3.6.1.4.1.248.11.22.1.2
OBJECT IDENTIFIER    

hm2DiagDeviceMonitorGroup 1.3.6.1.4.1.248.11.22.1.3
OBJECT IDENTIFIER    

hm2DiagLedGroup 1.3.6.1.4.1.248.11.22.1.4
OBJECT IDENTIFIER    

hm2DiagIfaceUtilizationGroup 1.3.6.1.4.1.248.11.22.1.5
OBJECT IDENTIFIER    

hm2DiagCableTesterGroup 1.3.6.1.4.1.248.11.22.1.6
OBJECT IDENTIFIER    

hm2PortMonitorGroup 1.3.6.1.4.1.248.11.22.1.7
OBJECT IDENTIFIER    

hm2DiagResourcesGroup 1.3.6.1.4.1.248.11.22.1.8
OBJECT IDENTIFIER    

hm2DiagSelftestRAM 1.3.6.1.4.1.248.11.22.1.1.1
Controls RAM self-test on cold start of the device. When disabled the device booting time is reduced.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2DiagSelftestBootTime 1.3.6.1.4.1.248.11.22.1.1.2
Internal boot time in Milliseconds until activating ports.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hm2DiagSelftestActionTable 1.3.6.1.4.1.248.11.22.1.1.10
Diag self test action group.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2DiagSelftestActionEntry

hm2DiagSelftestActionEntry 1.3.6.1.4.1.248.11.22.1.1.10.1
Diag self test action entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2DiagSelftestActionEntry  

hm2DiagSelftestActionCause 1.3.6.1.4.1.248.11.22.1.1.10.1.1
The area of the cause for the action the self-test wants to take.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER task(1), resource(2), software(3), hardware(4)  

hm2DiagSelftestAction 1.3.6.1.4.1.248.11.22.1.1.10.1.2
The action that the self-test component should take. The cause is always logged to the system log, additionally a trap can be sent to the management station or a reboot can be performed.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER logOnly(1), sendTrap(2), reboot(3)  

hm2BootSystemMonitor 1.3.6.1.4.1.248.11.22.1.2.1
Enable or disable the System Monitor access during the boot phase. Please note: If the System Monitor is disabled, it is possible to lose access to the device permanently in case of loosing administrator password or misconfiguration.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2BootDefaultConfigOnError 1.3.6.1.4.1.248.11.22.1.2.2
Enable or disable loading of the default configuration in case there is any error loading the configuration during the boot phase. If disabled the system will be halted.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2BootConfigPushButton 1.3.6.1.4.1.248.11.22.1.2.3
Enable or disable the push button functionality on the device.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2SignalContactGroup 1.3.6.1.4.1.248.11.22.1.3.1
OBJECT IDENTIFIER    

hm2SigConCommonTable 1.3.6.1.4.1.248.11.22.1.3.1.1
This table contains all variables to configure the behavior of the signalling contacts.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2SigConCommonEntry

hm2SigConCommonEntry 1.3.6.1.4.1.248.11.22.1.3.1.1.1
The entry of the hm2SigConConfigTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2SigConCommonEntry  

hm2SigConID 1.3.6.1.4.1.248.11.22.1.3.1.1.1.1
This index is used to identify the associated signalling contact.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..2  

hm2SigConTrapEnable 1.3.6.1.4.1.248.11.22.1.3.1.1.1.2
Determines whether a trap shall be sent or not, when the signal contact operating state changes.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2SigConTrapCause 1.3.6.1.4.1.248.11.22.1.3.1.1.1.3
This object identifies the cause for a trap. The index of the entity which produces the trap is specified by hm2SigConTrapCauseIndex.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(1), power-supply(2), link-failure(3), temperature(4), fan-failure(5), module-removal(6), ext-nvm-removal(7), ext-nvm-not-in-sync(8), ring-redundancy(9), password-change(10), password-min-length(11), password-policy-not-configured(12), password-policy-inactive(13), telnet-enabled(14), http-enabled(15), snmp-unsecure(16), sysmon-enabled(17), ext-nvm-update-enabled(18), no-link(19), hidisc-write-enabled(20), ext-nvm-config-load-unsecure(21), https-certificate-warning(23), modbus-tcp-enabled(24), ethernet-ip-enabled(25), profinet-io-enabled(26)  

hm2SigConTrapCauseIndex 1.3.6.1.4.1.248.11.22.1.3.1.1.1.4
This attribute specifies the entity which produces the trap. power-supply: index of power-supply table link-failure: index of interface table temperature: 0 ext-nvm-removal: (1) sd, (2) usb, (3) serial (not supported yet) ext-nvm-not-in-sync: (1) sd, (2) usb, (3) serial (not supported yet) ring-redundancy: (1) MRP, (2) PRP, (3) HSR, (4) DLR ext-nvm-update-enabled: (1) sd, (2) usb, (3) serial (not supported yet) no-link: index of interface table 0: other errors
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hm2SigConMode 1.3.6.1.4.1.248.11.22.1.3.1.1.1.5
This attribute specifies the behavior of the relay contact. The factory settings for signal contact 1 is monitoring the correct operation of entries specified to be survived. When the device has also a second signal contact, the factory setting for it is the manual mode.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER manual(1), monitor(2), deviceState(3), deviceSecurity(4), deviceStateAndSecurity(5)  

hm2SigConOperState 1.3.6.1.4.1.248.11.22.1.3.1.1.1.6
This attribute shows the current operating state of the signal contact.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER open(1), close(2)  

hm2SigConOperTimeStamp 1.3.6.1.4.1.248.11.22.1.3.1.1.1.7
This attribute shows local system time (hm2SystemLocalTime) of the last hm2SigConOperState change.
Status: current Access: read-only
OBJECT-TYPE    
  HmTimeSeconds1970  

hm2SigConManualActivate 1.3.6.1.4.1.248.11.22.1.3.1.1.1.8
When operating in manual mode, the signal contact state can be set by this attribute.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER open(1), close(2)  

hm2SigConSenseLinkFailure 1.3.6.1.4.1.248.11.22.1.3.1.1.1.9
Sets the monitoring of the network connection(s).
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2SigConSenseTemperature 1.3.6.1.4.1.248.11.22.1.3.1.1.1.10
Sets the monitoring of the device temperature.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2SigConSenseFan 1.3.6.1.4.1.248.11.22.1.3.1.1.1.11
Sets the monitoring of the device fan. (currently not supported)
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2SigConSenseModuleRemoval 1.3.6.1.4.1.248.11.22.1.3.1.1.1.12
Sets the monitoring of module removal (platform dependant).
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2SigConSenseExtNvmRemoval 1.3.6.1.4.1.248.11.22.1.3.1.1.1.13
Sets the monitoring of the external non-volatile memory removal.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2SigConSenseExtNvmNotInSync 1.3.6.1.4.1.248.11.22.1.3.1.1.1.14
Sets the monitoring whether the external non-volatile memory is in sync with the configuration in NVRAM.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2SigConSenseRingRedundancy 1.3.6.1.4.1.248.11.22.1.3.1.1.1.15
Sets the monitoring of the ring redundancy.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2SigConPSTable 1.3.6.1.4.1.248.11.22.1.3.1.2
This table contains the configuration of all power supply states.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2SigConPSEntry

hm2SigConPSEntry 1.3.6.1.4.1.248.11.22.1.3.1.2.1
The entry of the hm2SigConPSTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2SigConPSEntry  

hm2SigConSensePSState 1.3.6.1.4.1.248.11.22.1.3.1.2.1.1
Sets the monitoring of the power supply state.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2SigConInterfaceTable 1.3.6.1.4.1.248.11.22.1.3.1.3
This table contains all variables to mask an alarm for the signalling relay, produced by a link. The index for a link corresponds with ifIndex. The table is also used for the device monitoring configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2SigConInterfaceEntry

hm2SigConInterfaceEntry 1.3.6.1.4.1.248.11.22.1.3.1.3.1
The entry of the hm2SigConLinkTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2SigConInterfaceEntry  

hm2SigConSenseIfLinkAlarm 1.3.6.1.4.1.248.11.22.1.3.1.3.1.1
Indicates whether an alarm for the signalling relay of the associated link will be produced or not, so you can mask the value of ifMauMediaAvailable.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2SigConModuleTable 1.3.6.1.4.1.248.11.22.1.3.1.4
This table contains all variables to mask a module for the signaling relay. The index for a module corresponds with the slot number.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2SigConModuleEntry

hm2SigConModuleEntry 1.3.6.1.4.1.248.11.22.1.3.1.4.1
The entry of the hm2SigConModuleTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2SigConModuleEntry  

hm2SigConModID 1.3.6.1.4.1.248.11.22.1.3.1.4.1.1
This index is used to identify the associated module.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..7  

hm2SigConSenseModule 1.3.6.1.4.1.248.11.22.1.3.1.4.1.2
Indicates whether an alarm for the signalling relay of the associated module will be produced or not.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2SigConStatusTable 1.3.6.1.4.1.248.11.22.1.3.1.10
This table shows the current monitored entities for which there is a trap cause (hm2SigConTrapCause) active.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2SigConStatusEntry

hm2SigConStatusEntry 1.3.6.1.4.1.248.11.22.1.3.1.10.1
The entry of the hm2SigConStatusTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2SigConStatusEntry  

hm2SigConStatusIndex 1.3.6.1.4.1.248.11.22.1.3.1.10.1.1
This index is used to identify the occured event.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

hm2SigConStatusTimeStamp 1.3.6.1.4.1.248.11.22.1.3.1.10.1.2
This attribute shows the local system time (hm2SystemLocalTime) of occuration the event.
Status: current Access: read-only
OBJECT-TYPE    
  HmTimeSeconds1970  

hm2SigConStatusTrapCause 1.3.6.1.4.1.248.11.22.1.3.1.10.1.3
This object identifies the cause for a trap. The index of the entity which produces the trap is specified by hm2SigConTrapCauseIndex.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(1), power-supply(2), link-failure(3), temperature(4), fan-failure(5), module-removal(6), ext-nvm-removal(7), ext-nvm-not-in-sync(8), ring-redundancy(9), password-change(10), password-min-length(11), password-policy-not-configured(12), password-policy-inactive(13), telnet-enabled(14), http-enabled(15), snmp-unsecure(16), sysmon-enabled(17), ext-nvm-update-enabled(18), no-link(19), hidisc-write-enabled(20), ext-nvm-config-load-unsecure(21), iec61850-mms-enabled(22), https-certificate-warning(23), modbus-tcp-enabled(24), ethernet-ip-enabled(25), profinet-io-enabled(26)  

hm2SigConStatusTrapCauseIndex 1.3.6.1.4.1.248.11.22.1.3.1.10.1.4
This attribute specifies the entity which produces the trap. power-supply: index of power-supply table link-failure: index of interface table temperature: 0 ext-nvm-removal: (1) sd, (2) usb, (3) serial (not supported yet) ext-nvm-not-in-sync: (1) sd, (2) usb, (3) serial (not supported yet) ring-redundancy: (1) MRP, (2) PRP, (3) HSR, (4) DLR ext-nvm-update-enabled: (1) sd, (2) usb, (3) serial (not supported yet) no-link: index of interface table 0: other errors
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hm2DeviceMonitorGroup 1.3.6.1.4.1.248.11.22.1.3.2
OBJECT IDENTIFIER    

hm2DevMonCommonTable 1.3.6.1.4.1.248.11.22.1.3.2.1
This table contains all variables to configure the behavior of the signalling contacts.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2DevMonCommonEntry

hm2DevMonCommonEntry 1.3.6.1.4.1.248.11.22.1.3.2.1.1
The entry of the hm2DevMonConfigTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2DevMonCommonEntry  

hm2DevMonID 1.3.6.1.4.1.248.11.22.1.3.2.1.1.1
This index is used to identify the associated device monitoring group. Currently only one group is supported
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..1  

hm2DevMonTrapEnable 1.3.6.1.4.1.248.11.22.1.3.2.1.1.2
Determines whether a trap shall be sent or not when the signal contact operating state changes.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2DevMonTrapCause 1.3.6.1.4.1.248.11.22.1.3.2.1.1.3
This object identifies the cause for a trap. The index of the entity which produces the trap is specified by hm2DevMonTrapCauseIndex.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(1), power-supply(2), link-failure(3), temperature(4), fan-failure(5), module-removal(6), ext-nvm-removal(7), ext-nvm-not-in-sync(8), ring-redundancy(9)  

hm2DevMonTrapCauseIndex 1.3.6.1.4.1.248.11.22.1.3.2.1.1.4
This attribute specifies the entity which produces the trap. power-supply: index of power supply table link-failure: index of interface table temperature: 0 ext-nvm-removal: (1) sd, (2) usb, (3) Serial (not supported yet) ext-nvm-not-in-sync: (1) sd, (2) usb, (3) Serial (not supported yet) ring-redundancy: (1) MRP, (2) PRP, (3), HSR, (4) DLR 0: other errors
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hm2DevMonOperState 1.3.6.1.4.1.248.11.22.1.3.2.1.1.5
This attribute shows the current operating state of the signal contact.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER noerror(1), error(2)  

hm2DevMonOperTimeStamp 1.3.6.1.4.1.248.11.22.1.3.2.1.1.6
This attribute shows the local system time (hm2SystemLocalTime) of the last hm2DevMonOperState change.
Status: current Access: read-only
OBJECT-TYPE    
  HmTimeSeconds1970  

hm2DevMonSenseLinkFailure 1.3.6.1.4.1.248.11.22.1.3.2.1.1.7
Sets the monitoring of the network connection(s).
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2DevMonSenseTemperature 1.3.6.1.4.1.248.11.22.1.3.2.1.1.8
Sets the monitoring of the device temperature.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2DevMonSenseFan 1.3.6.1.4.1.248.11.22.1.3.2.1.1.9
Sets the monitoring of the device fan. (currently not supported)
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2DevMonSenseModuleRemoval 1.3.6.1.4.1.248.11.22.1.3.2.1.1.10
Sets the monitoring of module removal (platform dependent).
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2DevMonSenseExtNvmRemoval 1.3.6.1.4.1.248.11.22.1.3.2.1.1.11
Sets the monitoring of the external non-volatile memory removal.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2DevMonSenseExtNvmNotInSync 1.3.6.1.4.1.248.11.22.1.3.2.1.1.12
Sets the monitoring whether the external non-volatile memory is in sync with the configuration in NVRAM.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2DevMonSenseRingRedundancy 1.3.6.1.4.1.248.11.22.1.3.2.1.1.13
Sets the monitoring of the ring redundancy.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2DevMonPSTable 1.3.6.1.4.1.248.11.22.1.3.2.2
This table contains the configuration of all power supply states.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2DevMonPSEntry

hm2DevMonPSEntry 1.3.6.1.4.1.248.11.22.1.3.2.2.1
The entry of the hm2DevMonPSTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2DevMonPSEntry  

hm2DevMonSensePSState 1.3.6.1.4.1.248.11.22.1.3.2.2.1.1
Sets the monitoring of the power supply state.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2DevMonInterfaceTable 1.3.6.1.4.1.248.11.22.1.3.2.3
This table contains all variables to mask an alarm for the signalling relay, produced by a link. The index for a link corresponds with ifIndex. The table is also used for the device monitoring configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2DevMonInterfaceEntry

hm2DevMonInterfaceEntry 1.3.6.1.4.1.248.11.22.1.3.2.3.1
The entry of the hm2DevMonLinkTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2DevMonInterfaceEntry  

hm2DevMonSenseIfLinkAlarm 1.3.6.1.4.1.248.11.22.1.3.2.3.1.1
Indicates whether an alarm for the signalling relay of the associated link will be produced or not, so you can mask the value of ifMauMediaAvailable.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2DevMonModuleTable 1.3.6.1.4.1.248.11.22.1.3.2.4
This table contains all variables to mask a module for the device status. The index for a module corresponds with the slot number.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2DevMonModuleEntry

hm2DevMonModuleEntry 1.3.6.1.4.1.248.11.22.1.3.2.4.1
The entry of the hm2DevMonModuleTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2DevMonModuleEntry  

hm2DevMonModID 1.3.6.1.4.1.248.11.22.1.3.2.4.1.1
This index is used to identify the associated module.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..7  

hm2DevMonSenseModule 1.3.6.1.4.1.248.11.22.1.3.2.4.1.2
Indicates whether an alarm for the device status of the associated module will be produced or not.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2DevMonStatusTable 1.3.6.1.4.1.248.11.22.1.3.2.10
This table shows the current monitored entities in the hm2DeviceMonitorGroup for which there is a trap cause (hm2DevMonStatusTrapCause) active.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2DevMonStatusEntry

hm2DevMonStatusEntry 1.3.6.1.4.1.248.11.22.1.3.2.10.1
The entry of the hm2DevMonStatusTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2DevMonStatusEntry  

hm2DevMonStatusIndex 1.3.6.1.4.1.248.11.22.1.3.2.10.1.1
This index is used to identify the occured event.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

hm2DevMonStatusTimeStamp 1.3.6.1.4.1.248.11.22.1.3.2.10.1.2
This attribute shows the local system time (hm2SystemLocalTime) of occuration the event.
Status: current Access: read-only
OBJECT-TYPE    
  HmTimeSeconds1970  

hm2DevMonStatusTrapCause 1.3.6.1.4.1.248.11.22.1.3.2.10.1.3
This object identifies the cause for a trap. The index of the entity which produces the trap is specified by hm2DevMonTrapCauseIndex.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(1), power-supply(2), link-failure(3), temperature(4), fan-failure(5), module-removal(6), ext-nvm-removal(7), ext-nvm-not-in-sync(8), ring-redundancy(9)  

hm2DevMonStatusTrapCauseIndex 1.3.6.1.4.1.248.11.22.1.3.2.10.1.4
This attribute specifies the entity which produces the trap. power-supply: index of power supply table link-failure: index of interface table temperature: 0 ext-nvm-removal: (1) sd, (2) usb, (3) Serial (not supported yet) ext-nvm-not-in-sync: (1) sd, (2) usb, (3) Serial (not supported yet) ring-redundancy: (1) MRP, (2) PRP, (3) HSR, (4) DLR 0: other errors
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hm2DeviceSecurityGroup 1.3.6.1.4.1.248.11.22.1.3.3
OBJECT IDENTIFIER    

hm2DevSecConfigGroup 1.3.6.1.4.1.248.11.22.1.3.3.1
OBJECT IDENTIFIER    

hm2DevSecTrapEnable 1.3.6.1.4.1.248.11.22.1.3.3.1.1
Determines whether a trap shall be sent or not, when the device security operating state changes.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2DevSecTrapCause 1.3.6.1.4.1.248.11.22.1.3.3.1.2
This object identifies the cause for a trap. The index of the entity which produces the trap is specified by hm2DevMonTrapCauseIndex.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(1), password-change(10), password-min-length(11), password-policy-not-configured(12), password-policy-inactive(13), telnet-enabled(14), http-enabled(15), snmp-unsecure(16), sysmon-enabled(17), ext-nvm-update-enabled(18), no-link(19), hidisc-write-enabled(20), ext-nvm-config-load-unsecure(21), iec61850-mms-enabled(22), https-certificate-warning(23), modbus-tcp-enabled(24), ethernet-ip-enabled(25), profinet-io-enabled(26)  

hm2DevSecTrapCauseIndex 1.3.6.1.4.1.248.11.22.1.3.3.1.3
This attribute specifies the entity which produces the trap. ext-nvm-update-enabled: (1) sd, (2) usb, (3) serial (not supported yet) no-link: index of interface table 0: other errors.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hm2DevSecOperState 1.3.6.1.4.1.248.11.22.1.3.3.1.4
This attribute shows the current operating state of the signal contact.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER noerror(1), error(2)  

hm2DevSecOperTimeStamp 1.3.6.1.4.1.248.11.22.1.3.3.1.5
This attribute shows the local system time (hm2SystemLocalTime) of the last hm2DevSecOperState change.
Status: current Access: read-only
OBJECT-TYPE    
  HmTimeSeconds1970  

hm2DevSecSensePasswordChange 1.3.6.1.4.1.248.11.22.1.3.3.1.6
Enable or disable to check if default passwords for 'user' and 'admin' are not changed.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2DevSecSensePasswordMinLength 1.3.6.1.4.1.248.11.22.1.3.3.1.7
Enable or disable to check if configured minimum password length is < 8 characters.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2DevSecSensePasswordStrengthNotConfigured 1.3.6.1.4.1.248.11.22.1.3.3.1.8
Enable or disable minimum password strength to check if (1 uppercase, 1 lowercase, 1 number, 1 non-alphanumeric) is not configured.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2DevSecSenseBypassPasswordStrength 1.3.6.1.4.1.248.11.22.1.3.3.1.9
Enable or disable to check if at least one user is configured to bypass strength check.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2DevSecSenseTelnetEnabled 1.3.6.1.4.1.248.11.22.1.3.3.1.10
Enable or disable to check if telnet is enabled on the switch.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2DevSecSenseHttpEnabled 1.3.6.1.4.1.248.11.22.1.3.3.1.11
Enable or disable to check if HTTP is enabled on the switch.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2DevSecSenseSnmpUnsecure 1.3.6.1.4.1.248.11.22.1.3.3.1.12
Enable or disable to check if SNMP v1/v2 is enabled or v3 encryption is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2DevSecSenseSysmonEnabled 1.3.6.1.4.1.248.11.22.1.3.3.1.13
Enable or disable to check if sysmon1 access is not disabled.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2DevSecSenseExtNvmUpdateEnabled 1.3.6.1.4.1.248.11.22.1.3.3.1.14
Enable or disable to check if external non-volatile memory update is not disabled.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2DevSecSenseNoLinkEnabled 1.3.6.1.4.1.248.11.22.1.3.3.1.15
Enable or disable to check if at least one port has no link but admin state is up.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2DevSecSenseHiDiscoveryEnabled 1.3.6.1.4.1.248.11.22.1.3.3.1.16
Enable or disable to check if HiDiscovery is enabled and the mode is 'read-write'.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2DevSecSenseExtNvmConfigLoadUnsecure 1.3.6.1.4.1.248.11.22.1.3.3.1.17
Enable or disable to check if the configuration load from external NVM is unsecure. (The configuration priority of the external NVM is set to 'first', 'second' or 'third' and the configuration encryption is not active.)
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2DevSecSenseIec61850MmsEnabled 1.3.6.1.4.1.248.11.22.1.3.3.1.18
Enable or disable to check if IEC 61850 MMS is enabled on the switch.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2DevSecSenseHttpsCertificateWarning 1.3.6.1.4.1.248.11.22.1.3.3.1.19
Enable or disable to check for the presence of the auto generated self-signed HTTPS certificate.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2DevSecSenseModbusTcpEnabled 1.3.6.1.4.1.248.11.22.1.3.3.1.20
Enable or disable to check if Modbus/TCP server is enabled on the switch.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2DevSecSenseEtherNetIpEnabled 1.3.6.1.4.1.248.11.22.1.3.3.1.21
Enable or disable to check if EtherNet/IP protocol is enabled on the switch.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2DevSecSenseProfinetIOEnabled 1.3.6.1.4.1.248.11.22.1.3.3.1.22
Enable or disable to check if ProfinetIO protocol is enabled on the switch.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2DevSecInterfaceTable 1.3.6.1.4.1.248.11.22.1.3.3.2
This table contains all variables to mask an alarm for the signalling relay, produced by a link. The index for a link corresponds with ifIndex. The table is also used for the device monitoring configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2DevSecInterfaceEntry

hm2DevSecInterfaceEntry 1.3.6.1.4.1.248.11.22.1.3.3.2.1
The entry of the hm2DevSecLinkTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2DevSecInterfaceEntry  


hm2DevSecStatusTable 1.3.6.1.4.1.248.11.22.1.3.3.10
This table shows the current monitored entities in the hm2DevSecConfigGroup for which there is a trap cause (hm2DevSecStatusTrapCause) active.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2DevSecStatusEntry

hm2DevSecStatusEntry 1.3.6.1.4.1.248.11.22.1.3.3.10.1
The entry of the hm2DevSecStatusTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2DevSecStatusEntry  

hm2DevSecStatusIndex 1.3.6.1.4.1.248.11.22.1.3.3.10.1.1
This index is used to identify the occured event.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

hm2DevSecStatusTimeStamp 1.3.6.1.4.1.248.11.22.1.3.3.10.1.2
This attribute shows the local system time (hm2SystemLocalTime) of occuration the event.
Status: current Access: read-only
OBJECT-TYPE    
  HmTimeSeconds1970  

hm2DevSecStatusTrapCause 1.3.6.1.4.1.248.11.22.1.3.3.10.1.3
This object identifies the cause for a trap. The index of the entity which produces the trap is specified by hm2DevSecTrapCauseIndex.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(1), password-change(10), password-min-length(11), password-policy-not-configured(12), password-policy-inactive(13), telnet-enabled(14), http-enabled(15), snmp-unsecure(16), sysmon-enabled(17), ext-nvm-update-enabled(18), no-link(19), hidisc-write-enabled(20), ext-nvm-config-load-unsecure(21), iec61850-mms-enabled(22), https-certificate-warning(23), modbus-tcp-enabled(24), ethernet-ip-enabled(25), profinet-io-enabled(26)  

hm2DevSecStatusTrapCauseIndex 1.3.6.1.4.1.248.11.22.1.3.3.10.1.4
This attribute specifies the entity which produces the trap. ext-nvm-update-enabled: (1) sd, (2) usb, (3) serial (not supported yet) no-link: index of interface table 0: other errors.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hm2LedGlobalTable 1.3.6.1.4.1.248.11.22.1.4.1
.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2LedGlobalEntry

hm2LedGlobalEntry 1.3.6.1.4.1.248.11.22.1.4.1.1
.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2LedGlobalEntry  

hm2LedGlobalLedType 1.3.6.1.4.1.248.11.22.1.4.1.1.1
.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2LedType  

hm2LedGlobalStatus 1.3.6.1.4.1.248.11.22.1.4.1.1.2
.
Status: current Access: read-only
OBJECT-TYPE    
  Hm2LedStatus  

hm2LedPortTable 1.3.6.1.4.1.248.11.22.1.4.2
.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2LedPortEntry

hm2LedPortEntry 1.3.6.1.4.1.248.11.22.1.4.2.1
.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2LedPortEntry  

hm2LedPortStatus 1.3.6.1.4.1.248.11.22.1.4.2.1.1
.
Status: current Access: read-only
OBJECT-TYPE    
  Hm2LedStatus  

hm2LedPortPoeStatus 1.3.6.1.4.1.248.11.22.1.4.2.1.2
.
Status: current Access: read-only
OBJECT-TYPE    
  Hm2LedStatus  

hm2LedPortSignaling 1.3.6.1.4.1.248.11.22.1.4.2.1.3
Enable for LED port signaling.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2LedControlGroup 1.3.6.1.4.1.248.11.22.1.4.3
OBJECT IDENTIFIER    

hm2LedPortMode 1.3.6.1.4.1.248.11.22.1.4.3.1
Switch LED signalling between the port LEDs on front side (port panel) and the port LEDs on the back side (service panel) of the device.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER portpanel(0), servicepanel(1)  

hm2DiagIfaceUtilizationTable 1.3.6.1.4.1.248.11.22.1.5.1
This table contains variables for each interface of the switch.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2DiagIfaceUtilizationEntry

hm2DiagIfaceUtilizationEntry 1.3.6.1.4.1.248.11.22.1.5.1.1
The entry of the hm2DiagIfaceUtilizationTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2DiagIfaceUtilizationEntry  

hm2DiagIfaceUtilization 1.3.6.1.4.1.248.11.22.1.5.1.1.1
The best estimate of the mean physical layer network utilization on this interface during the last sampling interval, in hundredth of one percent. The first historyControlInterval (rfc1757) of this interface is used as sampling interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..10000  

hm2DiagIfaceUtilizationControlInterval 1.3.6.1.4.1.248.11.22.1.5.1.1.2
The interval in seconds over which the data is sampled for hmIfaceUtilization. This interval can be any number of seconds between 1 and 3600 (1 hour). The first historyControlInterval (rfc1757) of this interface is used as sampling interval.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..3600  

hm2DiagIfaceUtilizationAlarmLowerThreshold 1.3.6.1.4.1.248.11.22.1.5.1.1.3
Surveys the interface utilization hm2InfaceUtilization and generates an alarm for this interfaces, if the utilization value is below the given limit. A value of 0 disables the alarm generation.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..10000  

hm2DiagIfaceUtilizationAlarmUpperThreshold 1.3.6.1.4.1.248.11.22.1.5.1.1.4
Surveys the interface utilization hm2DiagIfaceUtilization and generates an alarm for this interfaces, if the given limit is exceeded. A value of 0 disables the alarm generation.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..10000  

hm2DiagIfaceUtilizationAlarmCondition 1.3.6.1.4.1.248.11.22.1.5.1.1.5
The alarm condition is given (true), if the given hm2DiagIfaceUtilizationAlarmUpperThreshold limit is exceeded by the interface utilization or if the utilization value falls below hm2DiagIfaceUtilizationAlarmLowerThreshold limit. The alarm condition will be removed, when the interface utilization value falls in between hm2DiagIfaceUtilizationAlarmLowerThreshold hm2DiagIfaceUtilizationAlarmUpperThreshold.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

hm2DiagCableTesterStatus 1.3.6.1.4.1.248.11.22.1.6.1
Status of the Virtual Cable Tester active(1) - Cable testing is in progress. Set to this value to start the test. success(2) - A successful test was performed. Cannot be set. failure(3) - A failure was encountered during the test. Cannot be set. uninitialized(4) - No test has been performed yet. Cannot be set.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER active(1), success(2), failure(3), uninitialized(4)  

hm2DiagCableTesterIfIndex 1.3.6.1.4.1.248.11.22.1.6.2
Determines on which port to perform the cable test. Limited to copper based ports.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

hm2DiagCableTesterCableTable 1.3.6.1.4.1.248.11.22.1.6.10
This table contains variables for each pair of the cable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2DiagCableTesterCableEntry

hm2DiagCableTesterCableEntry 1.3.6.1.4.1.248.11.22.1.6.10.1
The entry of the hm2DiagCableTesterCableTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2DiagCableTesterCableEntry  

hm2DiagCableTesterCablePair 1.3.6.1.4.1.248.11.22.1.6.10.1.1
Index of the hm2DiagCableTesterCableTable. If a PHY does not support the measurement per pair, the first index is used to show the values.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..4  

hm2DiagCableTesterCableStatus 1.3.6.1.4.1.248.11.22.1.6.10.1.2
Indicates the results of the Cable Test. normal(1) - The cable is working correctly. open(2) - The cable is disconnected or there is a faulty connector. short(3) - There is an electrical short in the cable. unknown(4) - No test has been performed yet, or a test is currently in progress.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER normal(1), open(2), short(3), unknown(4)  

hm2DiagCableTesterCableMinimumLength 1.3.6.1.4.1.248.11.22.1.6.10.1.3
The estimated length of the cable in meters. This value indicates the shortest length estimated. This object will return 0 if hm2DiagCableTesterStatus is not success(2) or the cable length is unknown.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hm2DiagCableTesterCableMaximumLength 1.3.6.1.4.1.248.11.22.1.6.10.1.4
The estimated length of the cable in meters. This value indicates the longest length estimated. This object will return 0 if hm2DiagCableTesterStatus is not success(2) or the cable length is unknown.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hm2DiagCableTesterCableFailureLocation 1.3.6.1.4.1.248.11.22.1.6.10.1.5
The estimated distance in meters from the end of the cable to the failure location. This object will return 0 if hm2DiagCableTesterStatus is not success(2).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hm2PortMonitorAdminMode 1.3.6.1.4.1.248.11.22.1.7.1
Global switch to enable / disable the port state actions, which are performed if a condition becomes true
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

hm2PortMonitorIntfTable 1.3.6.1.4.1.248.11.22.1.7.2
Port state mode interface table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2PortMonitorIntfEntry

hm2PortMonitorIntfEntry 1.3.6.1.4.1.248.11.22.1.7.2.1
Port state mode interface entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2PortMonitorIntfEntry  

hm2PortMonitorIntfReset 1.3.6.1.4.1.248.11.22.1.7.2.1.2
Port monitor interface reset.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

hm2PortMonitorIntfAction 1.3.6.1.4.1.248.11.22.1.7.2.1.3
Interface link disable state.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER port-disable(1), trap-only(2), auto-disable(3)  

hm2PortMonitorConditionGroup 1.3.6.1.4.1.248.11.22.1.7.3
OBJECT IDENTIFIER    

hm2KbpsUnitTrafficTypeInvalid 1.3.6.1.4.1.248.11.22.1.7.4
Interface {0}: 'Kbps' unit can only be used for traffic type 'all'.
Status: current Access: read-write
OBJECT-IDENTITY    

hm2PortMonitorConditionIntfTable 1.3.6.1.4.1.248.11.22.1.7.3.1
Port state condition interface table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2PortMonitorConditionIntfEntry

hm2PortMonitorConditionIntfEntry 1.3.6.1.4.1.248.11.22.1.7.3.1.1
Port state action interface entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2PortMonitorConditionIntfEntry  

hm2PortMonitorConditionField 1.3.6.1.4.1.248.11.22.1.7.3.1.1.1
Condition type field.
Status: current Access: read-only
OBJECT-TYPE    
  BITS none(0), link-flap(1), crcFragments(2), duplexMismatch(3), overload-detection(4), speed-duplex(5)  

hm2PortMonitorConditionLinkFlapMode 1.3.6.1.4.1.248.11.22.1.7.3.1.1.2
Interface link flap mode.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

hm2PortMonitorConditionCrcFragmentsMode 1.3.6.1.4.1.248.11.22.1.7.3.1.1.3
Interface CrcFragments mode.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

hm2PortMonitorConditionDuplexMismatchDetectionMode 1.3.6.1.4.1.248.11.22.1.7.3.1.1.4
Interface duplex mismatch detection mode.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

hm2PortMonitorConditionOverloadDetectionMode 1.3.6.1.4.1.248.11.22.1.7.3.1.1.5
Interface Overload Detection mode.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

hm2PortMonitorConditionSpeedDuplexMode 1.3.6.1.4.1.248.11.22.1.7.3.1.1.6
Interface Speed and Duplex monitor mode.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

hm2PortMonitorConditionLinkFlapGroup 1.3.6.1.4.1.248.11.22.1.7.3.2
OBJECT IDENTIFIER    

hm2PortMonitorConditionLinkFlapIntfTable 1.3.6.1.4.1.248.11.22.1.7.3.2.1
Port condition link flap interface table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2PortMonitorConditionLinkFlapIntfEntry

hm2PortMonitorConditionLinkFlapIntfEntry 1.3.6.1.4.1.248.11.22.1.7.3.2.1.1
Port condition link flap interface entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2PortMonitorConditionLinkFlapIntfEntry  

hm2PortMonitorConditionLinkFlapInterval 1.3.6.1.4.1.248.11.22.1.7.3.2.1.1.1
Measure interval in seconds (1-180s) for link flap detection.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..180  

hm2PortMonitorConditionLinkFlapCount 1.3.6.1.4.1.248.11.22.1.7.3.2.1.1.2
Link flap counter (1-100).
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..100  

hm2PortMonitorConditionLinkFlapCountInterval 1.3.6.1.4.1.248.11.22.1.7.3.2.1.1.3
Link flap count that occured in last interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hm2PortMonitorConditionLinkFlapCountTotal 1.3.6.1.4.1.248.11.22.1.7.3.2.1.1.4
Total link flap count.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hm2PortMonitorConditionCrcFragmentsGroup 1.3.6.1.4.1.248.11.22.1.7.3.3
OBJECT IDENTIFIER    

hm2PortMonitorConditionCrcFragmentsIntfTable 1.3.6.1.4.1.248.11.22.1.7.3.3.1
Port condition CrcFragments interface table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2PortMonitorConditionCrcFragmentsIntfEntry

hm2PortMonitorConditionCrcFragmentsIntfEntry 1.3.6.1.4.1.248.11.22.1.7.3.3.1.1
Port condition CrcFragments interface entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2PortMonitorConditionCrcFragmentsIntfEntry  

hm2PortMonitorConditionCrcFragmentsInterval 1.3.6.1.4.1.248.11.22.1.7.3.3.1.1.1
Measure interval in seconds (5-180s) for CrcFragments detection.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 5..180  

hm2PortMonitorConditionCrcFragmentsCount 1.3.6.1.4.1.248.11.22.1.7.3.3.1.1.2
CrcFragments counter (1-1000000).
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..1000000  

hm2PortMonitorConditionCrcFragmentsCountInterval 1.3.6.1.4.1.248.11.22.1.7.3.3.1.1.3
CrcFragments count that occured in last interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hm2PortMonitorConditionCrcFragmentsCountTotal 1.3.6.1.4.1.248.11.22.1.7.3.3.1.1.4
Total CrcFragments count.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hm2PortMonitorConditionOverloadDetectionGroup 1.3.6.1.4.1.248.11.22.1.7.3.4
OBJECT IDENTIFIER    

hm2PortMonitorConditionOvldDetIntfTable 1.3.6.1.4.1.248.11.22.1.7.3.4.1
Port condition overload detection interface table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2PortMonitorConditionOvldDetIntfEntry

hm2PortMonitorConditionOvldDetIntfEntry 1.3.6.1.4.1.248.11.22.1.7.3.4.1.1
Port condition overload detection interface entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2PortMonitorConditionOvldDetIntfEntry  

hm2PortMonitorConditionOvldDetTrfcType 1.3.6.1.4.1.248.11.22.1.7.3.4.1.1.1
Overload detection condition traffic type.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER all(1), bc(2), bc-mc(3)  

hm2PortMonitorConditionOvldDetTholdType 1.3.6.1.4.1.248.11.22.1.7.3.4.1.1.2
Overload detection conditon threshold type.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER pps(1), kbps(2)  

hm2PortMonitorConditionOvldDetLwrTholdVal 1.3.6.1.4.1.248.11.22.1.7.3.4.1.1.3
Overload detection condition lower threshold value.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..10000000  

hm2PortMonitorConditionOvldDetUprTholdVal 1.3.6.1.4.1.248.11.22.1.7.3.4.1.1.4
Overload detection condition upper threshold value.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..10000000  

hm2PortMonitorConditionOvldDetIntvl 1.3.6.1.4.1.248.11.22.1.7.3.4.1.1.5
Measure interval in seconds (1-20s) for overload detection.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..20  

hm2PortMonitorConditionOvldDetPkgCntAll 1.3.6.1.4.1.248.11.22.1.7.3.4.1.1.6
All package count from last interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hm2PortMonitorConditionOvldDetPkgCntBC 1.3.6.1.4.1.248.11.22.1.7.3.4.1.1.7
Broadcast package count from last interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hm2PortMonitorConditionOvldDetPkgCntMC 1.3.6.1.4.1.248.11.22.1.7.3.4.1.1.8
Overload detection condition lower threshold value.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hm2PortMonitorConditionOvldDetPkgCntKbit 1.3.6.1.4.1.248.11.22.1.7.3.4.1.1.9
Overload detection condition lower threshold value.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hm2PortMonitorConditionSpeedDuplexGroup 1.3.6.1.4.1.248.11.22.1.7.3.5
OBJECT IDENTIFIER    

hm2PortMonitorConditionSpeedDuplexTable 1.3.6.1.4.1.248.11.22.1.7.3.5.1
Port condition speed-duplex interface table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2PortMonitorConditionSpeedDuplexEntry

hm2PortMonitorConditionSpeedDuplexEntry 1.3.6.1.4.1.248.11.22.1.7.3.5.1.1
Port condition speed-duplex interface entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2PortMonitorConditionSpeedDuplexEntry  

hm2PortMonitorConditionSpeedDuplexValue 0.1.2.3.4.5.6.1.3.6.1.4.1.248.11.22.1.7.3.5.1.1.1
Speed and duplex combination allowed by port-monitor.
Status: current Access: read-write
OBJECT-TYPE    
  BITS hdx-10(0), fdx-10(1), hdx-100(2), fdx-100(3), hdx-1000(4), fdx-1000(5), fdx-2500(6)  

hm2DiagEnableMeasurement 1.3.6.1.4.1.248.11.22.1.8.1
Enable or disable the resources measurement If disabled, the task - needed for measurement - is also deleted.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2DiagCpuResourcesGroup 1.3.6.1.4.1.248.11.22.1.8.10
OBJECT IDENTIFIER    

hm2DiagCpuUtilization 1.3.6.1.4.1.248.11.22.1.8.10.1
The current cpu utilization of the device in percent.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..100  

hm2DiagCpuAverageUtilization 1.3.6.1.4.1.248.11.22.1.8.10.2
The average cpu utilization of the device in percent, max. measured over the last 30 minutes.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..100  

hm2DiagCpuRunningProcesses 1.3.6.1.4.1.248.11.22.1.8.10.3
The current number of processes running.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..32768  

hm2DiagCpuMaxRunningProcesses 1.3.6.1.4.1.248.11.22.1.8.10.4
The maximum number of processes running, max. since the last 30 minutes.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..32768  

hm2DiagMemoryResourcesGroup 1.3.6.1.4.1.248.11.22.1.8.11
OBJECT IDENTIFIER    

hm2DiagMemoryRamAllocated 1.3.6.1.4.1.248.11.22.1.8.11.1
The current allocated RAM of the device in kBytes.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..2147483647  

hm2DiagMemoryRamFree 1.3.6.1.4.1.248.11.22.1.8.11.2
The current free RAM of the device in kBytes.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..2147483647  

hm2DiagMemoryRamAllocatedAverage 1.3.6.1.4.1.248.11.22.1.8.11.3
The average allocated RAM of the device in kBytes, measured over the last 30 minutes.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..2147483647  

hm2DiagMemoryRamFreeAverage 1.3.6.1.4.1.248.11.22.1.8.11.4
The average free RAM of the device in kBytes, measured over the last 30 minutes.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..2147483647  

hm2DiagMemoryRawFlashMainAllocated 1.3.6.1.4.1.248.11.22.1.8.11.10
The current allocated flash memory for the main software image in kBytes.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..2147483647  

hm2DiagMemoryRawFlashMainFree 1.3.6.1.4.1.248.11.22.1.8.11.11
The current free flash memory for the main software image in kBytes.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..2147483647  

hm2DiagMemoryFlashFileSystemAllocated 1.3.6.1.4.1.248.11.22.1.8.11.12
The current allocated memory within the flash file system in kBytes.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..2147483647  

hm2DiagMemoryFlashFileSystemFree 1.3.6.1.4.1.248.11.22.1.8.11.13
The current free memory within the flash file system in kBytes.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..2147483647  

hm2DiagNetworkResourcesGroup 1.3.6.1.4.1.248.11.22.1.8.12
OBJECT IDENTIFIER    

hm2DiagNetworkCpuIfUtilization 1.3.6.1.4.1.248.11.22.1.8.12.1
The current network utilization of the internal cpu interface in percent.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..100  

hm2DiagNetworkCpuIfAverageUtilization 1.3.6.1.4.1.248.11.22.1.8.12.2
The average network utilization of the internal cpu interface in percent, measured over the last 30 minutes.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..100  

hm2SigConStateChangeTrap 1.3.6.1.4.1.248.11.22.0.1
This trap is sent if the value of hm2SigConState changes its value.
Status: current Access: read-only
NOTIFICATION-TYPE    

hm2DevMonStateChangeTrap 1.3.6.1.4.1.248.11.22.0.2
This trap is sent if the value of hm2DevMonState changes its value.
Status: current Access: read-only
NOTIFICATION-TYPE    

hm2DevSecStateChangeTrap 1.3.6.1.4.1.248.11.22.0.3
This trap is sent if the value of hm2DevSecState changes its value.
Status: current Access: read-only
NOTIFICATION-TYPE    

hm2DiagSelftestActionTrap 1.3.6.1.4.1.248.11.22.0.4
This trap is sent if a self-test action is performed and hm2DiagSelftestAction is configured to sendTrap(2).
Status: current Access: read-only
NOTIFICATION-TYPE    

hm2DiagIfaceUtilizationTrap 1.3.6.1.4.1.248.11.22.0.5
This trap is sent if the value of hmIfaceUtilization exceeds or falls back below the interface utilization thresholds hmIfaceUtilizationAlarmConditionThreshold and hmIfaceUtilizationAlarmRemovalThreshold.
Status: current Access: read-only
NOTIFICATION-TYPE    

hm2PortMonitorPortTrap 1.3.6.1.4.1.248.11.22.0.6
This trap is sent if the a port has been disabled by port disable action by port monitor.
Status: current Access: read-only
NOTIFICATION-TYPE    

hm2PortMonitorSpeedDuplexErrorReturn 1.3.6.1.4.1.248.11.22.3.1
Indicates that the specified speed value is not supported by the port capabilities
Status: current Access: read-only
OBJECT-IDENTITY    

hm2PortMonitorCndOvldDetInconsistenTholdVal 1.3.6.1.4.1.248.11.22.3.2
Indicates that the configured upper and lower threshold values are inconsistent
Status: current Access: read-only
OBJECT-IDENTITY    

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor