HM2-DEVMGMT-MIB

Imported modules

SNMPv2-SMI	SNMPv2-TC	SNMP-FRAMEWORK-MIB
IF-MIB	HM2-TC-MIB	IANAifType-MIB

Imported symbols

MODULE-IDENTITY	OBJECT-TYPE	Integer32
Unsigned32	NOTIFICATION-TYPE	TEXTUAL-CONVENTION
DisplayString	TruthValue	SnmpAdminString
ifIndex	InterfaceIndexOrZero	HmEnabledStatus
HmTimeSeconds1970	hm2ConfigurationMibs	IANAifType

Defined Types

Hm2DeviceExtNVMType
Type of an external non volatile memory device.
TEXTUAL-CONVENTION
	INTEGER	none(0), sd(1), usb(2), serial(3)

Hm2DevMgmtSwVersEntry
SEQUENCE
	hm2DevMgmtSwFileLocation	INTEGER
	hm2DevMgmtSwFileType	INTEGER
	hm2DevMgmtSwFileIdx	Integer32
	hm2DevMgmtSwFileName	DisplayString
	hm2DevMgmtSwVersion	DisplayString
	hm2DevMgmtSwMajorRelNum	Integer32
	hm2DevMgmtSwMinorRelNum	Integer32
	hm2DevMgmtSwBugfixRelNum	Integer32

Hm2DevMgmtLogicVersEntry
SEQUENCE
	hm2DevMgmtLogicIdx	Integer32
	hm2DevMgmtLogicAddress	DisplayString
	hm2DevMgmtLogicVersion	DisplayString

Hm2IfaceEntry
SEQUENCE
	hm2IfacePhysIndex	Integer32
	hm2IfacePortCapabilityBits	BITS
	hm2IfaceCableCrossing	INTEGER
	hm2IfacePowerState	HmEnabledStatus
	hm2IfaceAutoPowerDown	INTEGER
	hm2IfaceOperAdminStatus	INTEGER

Hm2IfaceLayoutEntry
SEQUENCE
	hm2IfaceLayoutIndex	Integer32
	hm2IfaceLayoutStartIfIndex	InterfaceIndexOrZero
	hm2IfaceLayoutEndIfIndex	InterfaceIndexOrZero
	hm2IfaceLayoutModuleCapacity	Unsigned32
	hm2IfaceLayoutModulePortCapacity	Unsigned32
	hm2IfaceLayoutFormat	SnmpAdminString
	hm2IfaceLayoutIfIndexType	IANAifType

Hm2IfaceExtEntry
SEQUENCE
	hm2IfaceExtIfRole	INTEGER

Hm2SfpInfoEntry
SEQUENCE
	hm2SfpModuleType	INTEGER
	hm2SfpMediaType	INTEGER
	hm2SfpConnector	INTEGER
	hm2SfpVendorName	SnmpAdminString
	hm2SfpVendorOUI	OCTET STRING
	hm2SfpPartNumber	SnmpAdminString
	hm2SfpPartRev	SnmpAdminString
	hm2SfpSerialNum	SnmpAdminString
	hm2SfpDateCode	SnmpAdminString
	hm2SfpInfoVersion	Integer32
	hm2SfpInfoPartNumber	SnmpAdminString
	hm2SfpInfoPartId	SnmpAdminString
	hm2SfpBitRateNominal	Integer32
	hm2SfpBitRateMin	Integer32
	hm2SfpBitRateMax	Integer32
	hm2SfpMaxLength-fiber-9	Integer32
	hm2SfpMaxLength-fiber-50	Integer32
	hm2SfpMaxLength-fiber-e50	Integer32
	hm2SfpMaxLength-fiber-62-5	Integer32
	hm2SfpMaxLength-copper	Integer32
	hm2SfpWaveLength	Integer32
	hm2SfpWaveLengthTolerance	Integer32
	hm2SfpEnhancedOptions	BITS
	hm2SfpSupported	TruthValue
	hm2SfpSupportedReason	INTEGER

Hm2SfpDiagEntry
SEQUENCE
	hm2SfpCurrentBitRate	Integer32
	hm2SfpCurrentTemperature	Integer32
	hm2SfpCurrentTxPower	Integer32
	hm2SfpCurrentRxPower	Integer32
	hm2SfpCurrentTxPowerdBm	SnmpAdminString
	hm2SfpCurrentRxPowerdBm	SnmpAdminString
	hm2SfpCurrentRxPowerState	INTEGER

Hm2SfpThresholdEntry
SEQUENCE
	hm2SfpTemperatureHighAlarm	Integer32
	hm2SfpTemperatureHighWarning	Integer32
	hm2SfpTemperatureLowAlarm	Integer32
	hm2SfpTemperatureLowWarning	Integer32
	hm2SfpTxPowerHighAlarm	Integer32
	hm2SfpTxPowerHighWarning	Integer32
	hm2SfpTxPowerLowAlarm	Integer32
	hm2SfpTxPowerLowWarning	Integer32
	hm2SfpRxPowerHighAlarm	Integer32
	hm2SfpRxPowerHighWarning	Integer32
	hm2SfpRxPowerLowAlarm	Integer32
	hm2SfpRxPowerLowWarning	Integer32
	hm2SfpTxPowerdBmHighAlarm	SnmpAdminString
	hm2SfpTxPowerdBmHighWarning	SnmpAdminString
	hm2SfpTxPowerdBmLowAlarm	SnmpAdminString
	hm2SfpTxPowerdBmLowWarning	SnmpAdminString
	hm2SfpRxPowerdBmHighAlarm	SnmpAdminString
	hm2SfpRxPowerdBmHighWarning	SnmpAdminString
	hm2SfpRxPowerdBmLowAlarm	SnmpAdminString
	hm2SfpRxPowerdBmLowWarning	SnmpAdminString

Hm2ExtNvmEntry
SEQUENCE
	hm2ExtNvmTableIndex	Hm2DeviceExtNVMType
	hm2ExtNvmStatus	INTEGER
	hm2ExtNvmManufacturerId	DisplayString
	hm2ExtNvmHWRevision	DisplayString
	hm2ExtNvmProductName	DisplayString
	hm2ExtNvmVersion	DisplayString
	hm2ExtNvmSerialNum	DisplayString
	hm2ExtNvmAutomaticSoftwareLoad	HmEnabledStatus
	hm2ExtNvmConfigLoadPriority	INTEGER
	hm2ExtNvmConfigSave	HmEnabledStatus
	hm2ExtNvmWritable	HmEnabledStatus
	hm2ExtNvmAutomaticSshKeyLoad	HmEnabledStatus

Hm2AutoDisableIntfEntry
SEQUENCE
	hm2AutoDisableIntfRemainingTime	Unsigned32
	hm2AutoDisableIntfComponentName	SnmpAdminString
	hm2AutoDisableIntfErrorReason	INTEGER
	hm2AutoDisableIntfTimer	Unsigned32
	hm2AutoDisableIntfReset	TruthValue
	hm2AutoDisableIntfOperState	INTEGER
	hm2AutoDisableIntfErrorTime	HmTimeSeconds1970

Hm2AutoDisableReasonEntry
SEQUENCE
	hm2AutoDisableReasons	INTEGER
	hm2AutoDisableReasonOperation	HmEnabledStatus
	hm2AutoDisableReasonCategory	INTEGER

Hm2UnitEntry
SEQUENCE
	hm2UnitIndex	Integer32
	hm2UnitMaxModuleCapacity	Integer32
	hm2UnitMaxModulePortCapacity	Integer32

Hm2ModuleEntry
SEQUENCE
	hm2ModuleIndex	Integer32
	hm2ModuleId	OBJECT IDENTIFIER
	hm2ModuleDescription	SnmpAdminString
	hm2ModuleProductCode	SnmpAdminString
	hm2ModuleVersion	SnmpAdminString
	hm2ModuleNumOfPorts	Integer32
	hm2ModuleFirstMauIndex	Integer32
	hm2ModuleStatus	INTEGER
	hm2ModuleSerialNum	SnmpAdminString
	hm2ModuleMinSWVersion	Integer32
	hm2ModuleCapability	BITS
	hm2ModuleInternalID	Integer32
	hm2ModuleInternalIDVariant	Integer32
	hm2ModuleFirstIfIndex	Integer32
	hm2ModuleAdminState	HmEnabledStatus

Defined Values

hm2DeviceMgmtMib		1.3.6.1.4.1.248.11.10
Hirschmann Device Management MIB. Copyright (C) 2012. All Rights Reserved.
MODULE-IDENTITY

hm2DeviceMgmtMibNotifications		1.3.6.1.4.1.248.11.10.0
OBJECT IDENTIFIER

hm2DeviceMgmtMibObjects		1.3.6.1.4.1.248.11.10.1
OBJECT IDENTIFIER

hm2DeviceMgmtGroup		1.3.6.1.4.1.248.11.10.1.1
OBJECT IDENTIFIER

hm2DeviceMgmtActionGroup		1.3.6.1.4.1.248.11.10.1.2
OBJECT IDENTIFIER

hm2DeviceMgmtSoftwareGroup		1.3.6.1.4.1.248.11.10.1.3
OBJECT IDENTIFIER

hm2DeviceMgmtHardwareGroup		1.3.6.1.4.1.248.11.10.1.4
OBJECT IDENTIFIER

hm2DeviceMgmtTemperatureGroup		1.3.6.1.4.1.248.11.10.1.5
OBJECT IDENTIFIER

hm2IfaceGroup		1.3.6.1.4.1.248.11.10.1.6
OBJECT IDENTIFIER

hm2SfpGroup		1.3.6.1.4.1.248.11.10.1.7
OBJECT IDENTIFIER

hm2ExtNvmGroup		1.3.6.1.4.1.248.11.10.1.8
OBJECT IDENTIFIER

hm2AutoDisableGroup		1.3.6.1.4.1.248.11.10.1.9
OBJECT IDENTIFIER

hm2UnitGroup		1.3.6.1.4.1.248.11.10.1.10
OBJECT IDENTIFIER

hm2ModuleGroup		1.3.6.1.4.1.248.11.10.1.11
OBJECT IDENTIFIER

hm2DevMgmtProductId		1.3.6.1.4.1.248.11.10.1.1.1
Manufacturer-defined product identifier (product family + product ID). Example:Objekt-ID 1.3.6.1.4.1.248.11.2.1.1 is the hm2ProductFamily EES and Objekt-ID 1.3.6.1.4.1.248.11.2.1.1.2 is the Product ID for ees25-0600
Status: current	Access: read-only
OBJECT-TYPE
	OBJECT IDENTIFIER

hm2DevMgmtProductDescr		1.3.6.1.4.1.248.11.10.1.1.2
Manufacturer-defined product description.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

hm2DevMgmtSerialNumber		1.3.6.1.4.1.248.11.10.1.1.3
Manufacturer-defined serial number of the device.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

hm2DevMgmtActionReset		1.3.6.1.4.1.248.11.10.1.2.1
Setting the object to 'reset' has the same effect as a power-on sequence (cold start) Reading the object always returns 'other'.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), reset(2)

hm2DevMgmtActionFlushFDB		1.3.6.1.4.1.248.11.10.1.2.2
Setting the object to 'flushFDB' will flush the forwarding database of the switch. Reading the object always returns 'other'.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), flushFDB(2)

hm2DevMgmtActionFlushARP		1.3.6.1.4.1.248.11.10.1.2.3
Setting the object to 'flushARP' will flush the ARP cache. Reading the object always returns 'other'.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), flushARP(2)

hm2DevMgmtActionFlushIGS		1.3.6.1.4.1.248.11.10.1.2.4
Setting the object to 'flushIGS' will flush all dynamically learnt IGMP snooping entries. Reading the object always returns 'other'.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), flushIGS(2)

hm2DevMgmtActionFlushPortStats		1.3.6.1.4.1.248.11.10.1.2.5
Setting the object to 'flushPortStats' will flush all port statistics. Reading the object always returns 'other'.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), flushPortStats(2)

hm2DevMgmtActionFlushEmailLogStats		1.3.6.1.4.1.248.11.10.1.2.6
Setting the object to 'flushEmailLogCounters' will flush all email logging statistics. Reading the object always returns 'other'.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), flushEmailLogCounters(2)

hm2DevMgmtActionFlushMMRP		1.3.6.1.4.1.248.11.10.1.2.7
Setting the object to 'flushMMRP' will flush all MMRP counters. Reading the object always returns 'other'.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), flushMMRP(2)

hm2DevMgmtActionFlushMVRP		1.3.6.1.4.1.248.11.10.1.2.8
Setting the object to 'flushMVRP' will flush all MVRP counters. Reading the object always returns 'other'.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), flushMVRP(2)

hm2DevMgmtActionFlushMSRP		1.3.6.1.4.1.248.11.10.1.2.9
Setting the object to 'flushMSRP' will flush all MSRP counters. Reading the object always returns 'other'.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), flushMSRP(2)

hm2DevMgmtActionFlushIeee8021AS		1.3.6.1.4.1.248.11.10.1.2.10
Setting the object to 'flushIeee8021AS' will flush all IEEE8021AS related counters. Reading the object always returns 'other'.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), flushIeee8021AS(2)

hm2DevMgmtActionFlushDnsClientCache		1.3.6.1.4.1.248.11.10.1.2.11
Setting the object to 'flushDnsClientCache' will flush all DNS client cache records. Reading the object always returns 'other'.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), flushDnsClientCache(2)

hm2DevMgmtActionFlushDnsCachingServerCache		1.3.6.1.4.1.248.11.10.1.2.12
Setting the object to 'flushDnsCachingServerCache' will flush all DNS caching server cache records. Reading the object always returns 'other'.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), flushDnsCachingServerCache(2)

hm2DevMgmtActionFlushIpUdpHelperStats		1.3.6.1.4.1.248.11.10.1.2.13
Setting the object to 'flushIpUdpHelperStats' will flush all ip udp helper statistics. Reading the object always returns 'other'.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), flushIpUdpHelperStats(2)

hm2DevMgmtActionFlushAclStats		1.3.6.1.4.1.248.11.10.1.2.14
Setting the object to 'flushAclStats' will flush all acl statistics from the AgentAclRuleTable. Setting the object to 'flushAclMacStats' will flush all acl statistics from the AgentAclMacRuleTable. Reading the object always returns 'other'.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), flushAclStats(2), flushAclMacStats(3)

hm2DevMgmtActionFlushLdapUserCache		1.3.6.1.4.1.248.11.10.1.2.15
Setting the object to 'flushLdapUserCache' will flush all cached users from LDAP queries to an Active Directory Server. Reading the object always returns 'other'.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), flushLdapUserCache(2)

hm2DevMgmtActionDelayPreset		1.3.6.1.4.1.248.11.10.1.2.100
Time in seconds until a reset that was triggered over the hm2DevMgmtActionReset object is executed. Writing a zero will cancel any scheduled reset.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..2147483

hm2DevMgmtActionDelayCurrent		1.3.6.1.4.1.248.11.10.1.2.101
If a delayed reset is scheduled this object will decrement from the start value to zero.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483

hm2DeviceMgmtSoftwareVersionGroup		1.3.6.1.4.1.248.11.10.1.3.1
OBJECT IDENTIFIER

hm2DevMgmtSwVersBootcode		1.3.6.1.4.1.248.11.10.1.3.1.1
Software version of the boot code.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

hm2DevMgmtSwVersTable		1.3.6.1.4.1.248.11.10.1.3.1.10
This table contains all information related to running and stored software versions on the device. The limit are 24 firmware (*.bin) files in up to 5 directory levels.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hm2DevMgmtSwVersEntry

hm2DevMgmtSwVersEntry		1.3.6.1.4.1.248.11.10.1.3.1.10.1
The entry of the hm2DevMgmtSwVersTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hm2DevMgmtSwVersEntry

hm2DevMgmtSwFileLocation		1.3.6.1.4.1.248.11.10.1.3.1.10.1.1
Indicates the file location (ram, flash, sd-card or usb).
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	ram(1), flash(2), sd-card(3), usb(4)

hm2DevMgmtSwFileType		1.3.6.1.4.1.248.11.10.1.3.1.10.1.2
Indicates the file type (firmware, applet, logic).
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	firmware(1), applet(2), logic(3)

hm2DevMgmtSwFileIdx		1.3.6.1.4.1.248.11.10.1.3.1.10.1.3
Indicates the index. For flash the index has the following meaning: - flash.xxx.1 = bootable version in flash (ROM) - flash.xxx.2 = backup version in flash (BAK)
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..25

hm2DevMgmtSwFileName		1.3.6.1.4.1.248.11.10.1.3.1.10.1.4
Indicates the file name.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

hm2DevMgmtSwVersion		1.3.6.1.4.1.248.11.10.1.3.1.10.1.5
Version of the stored software.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

hm2DevMgmtSwMajorRelNum		1.3.6.1.4.1.248.11.10.1.3.1.10.1.6
Shows the major release number of the firmware.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hm2DevMgmtSwMinorRelNum		1.3.6.1.4.1.248.11.10.1.3.1.10.1.7
Shows the minor release number of the firmware.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hm2DevMgmtSwBugfixRelNum		1.3.6.1.4.1.248.11.10.1.3.1.10.1.8
Shows the bug fix release number of the firmware.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hm2DevMgmtHwVersion		1.3.6.1.4.1.248.11.10.1.4.1
Version of the device hardware.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

hm2DevMgmtSwitchingCoreVersion		1.3.6.1.4.1.248.11.10.1.4.2
Version of the device hardware.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

hm2DeviceMgmtLogicVersionGroup		1.3.6.1.4.1.248.11.10.1.4.5
OBJECT IDENTIFIER

hm2DevMgmtLogicVersTable		1.3.6.1.4.1.248.11.10.1.4.5.1
The table displays all versions of supported logic modules.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hm2DevMgmtLogicVersEntry

hm2DevMgmtLogicVersEntry		1.3.6.1.4.1.248.11.10.1.4.5.1.1
The entry of the hm2DevMgmtLogicVersTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hm2DevMgmtLogicVersEntry

hm2DevMgmtLogicIdx		1.3.6.1.4.1.248.11.10.1.4.5.1.1.1
Index of the module to display.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..32

hm2DevMgmtLogicAddress		1.3.6.1.4.1.248.11.10.1.4.5.1.1.2
Address of the logic module in fpga.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

hm2DevMgmtLogicVersion		1.3.6.1.4.1.248.11.10.1.4.5.1.1.3
Version of the logic module in fpga.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

hm2DevMgmtTemperature		1.3.6.1.4.1.248.11.10.1.5.1
This object is used to identify the temperature within a device in units of centigrade (Celsius).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hm2DevMgmtTemperatureUpperLimit		1.3.6.1.4.1.248.11.10.1.5.2
This object is used to define a maximum level for the temperature within a device. If the temperature rises above this upper limit, the management station will be notified by a hm2DevMgmtTemperature trap.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	-99..99

hm2DevMgmtTemperatureLowerLimit		1.3.6.1.4.1.248.11.10.1.5.3
This object is used to define a minimum level for the temperature within a device. If the temperature falls below this lower limit, the management station will be notified by a hm2DevMgmtTemperature trap.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	-99..99

hm2IfaceTable		1.3.6.1.4.1.248.11.10.1.6.1
This table contains extended PHY capabilities and configuration options.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hm2IfaceEntry

hm2IfaceEntry		1.3.6.1.4.1.248.11.10.1.6.1.1
Entry with the configuration options and supported features of a port.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hm2IfaceEntry

hm2IfacePhysIndex		1.3.6.1.4.1.248.11.10.1.6.1.1.1
The index of the available physical interfaces.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

hm2IfacePortCapabilityBits		1.3.6.1.4.1.248.11.10.1.6.1.1.2
manual-mdix - port supports MDIX and MDI auto-mdix - port supports MDIX and Auto-MDIX auto-power-down - port can enter low power mode if no link is established energy-efficient-ethernet - port supports EEE cable-test - port supports cable testing
Status: current	Access: read-only
OBJECT-TYPE
	BITS	manual-mdix(0), auto-mdix(1), auto-power-down(2), energy-efficient-ethernet(3), cable-test(4)

hm2IfaceCableCrossing		1.3.6.1.4.1.248.11.10.1.6.1.1.3
This variable configures the cable crossing on twisted pair cables. When set to 'mdi', the device does not swap the send and receive line pairs of the TP cable for this port. When set to 'mdix', the device swaps the send and receive line pairs of the TP cable for this port. When set to 'auto-mdix', the port uses the auto crossover mode. 'Unsupported' is shown, if a port does not support cable crossing or auto-negotiation is disabled. It is not possible to set 'unsupported' to any type of port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	mdi(1), mdix(2), auto-mdix(3), unsupported(4)

hm2IfacePowerState		1.3.6.1.4.1.248.11.10.1.6.1.1.4
This variable configures the power on the interface. When set to 'enable' that means the interface-power is on (power up) When set to 'disable' that means the interface-power is off (power down) The interface power state settings have no effect if the interface admin state (ifAdminStatus) is enabled
Status: current	Access: read-write
OBJECT-TYPE
	HmEnabledStatus

hm2IfaceAutoPowerDown		1.3.6.1.4.1.248.11.10.1.6.1.1.5
This variable configures the automatic power save mode on the interface. When set to 'auto-power-down', the port goes in a low power mode if no link is detected. When set to 'no-power-save', the port does not use the automatic power save mode. When set to 'energy-efficient-ethernet', the port uses energy-efficient-ethernet mode to save the power. 'Unsupported' is shown, if a port does not support automatic power save mode.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	auto-power-down(1), no-power-save(2), energy-efficient-ethernet(3), unsupported(4)

hm2IfaceOperAdminStatus		1.3.6.1.4.1.248.11.10.1.6.1.1.6
This variable shows the operational admin state of a specific interface. The operational state could be different to the ifAdminStatus if the interface is forced to down by other means like hm2AutoDisableIntfOperState.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2)

hm2IfaceLayoutTable		1.3.6.1.4.1.248.11.10.1.6.2
This table does contain the layout of the interface modules or blocks. It contains all possible physical and logical items. This table can be used to determine any interface index according to 'IfEntry' that may exist and the name of this interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hm2IfaceLayoutEntry

hm2IfaceLayoutEntry		1.3.6.1.4.1.248.11.10.1.6.2.1
An entry of a module or block of interfaces.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hm2IfaceLayoutEntry

hm2IfaceLayoutIndex		1.3.6.1.4.1.248.11.10.1.6.2.1.1
The index used for this table.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32

hm2IfaceLayoutStartIfIndex		1.3.6.1.4.1.248.11.10.1.6.2.1.2
It specifies the first interface index of this block or module.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndexOrZero

hm2IfaceLayoutEndIfIndex		1.3.6.1.4.1.248.11.10.1.6.2.1.3
It specifies the last interface index of this block or module that can exist for this particular device. The amount of interfaces between first and last may not be equal than to the maximum interface per module.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndexOrZero

hm2IfaceLayoutModuleCapacity		1.3.6.1.4.1.248.11.10.1.6.2.1.4
It is the Number of modules in that block. Currently not used and it is always 0.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hm2IfaceLayoutModulePortCapacity		1.3.6.1.4.1.248.11.10.1.6.2.1.5
Number of interfaces that one module can contain. Currently not used and it is always 0
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hm2IfaceLayoutFormat		1.3.6.1.4.1.248.11.10.1.6.2.1.6
This specifies a format string that can be used to determine the textual representation of an interface in this block. following wildcards are supported: %i the absolute interface number according to 'IfEntry'. %p the relative number based on hm2IfaceLayoutStartIfIndex %s the block number from 'hm2IfaceLayoutIndex' %vid the vlan of the routing interface %lre the name of the redundancy port (prp or hsr)
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString

hm2IfaceLayoutIfIndexType		1.3.6.1.4.1.248.11.10.1.6.2.1.7
Type of the interfaces in that block according to IANA-Type table.
Status: current	Access: read-only
OBJECT-TYPE
	IANAifType

hm2IfaceExtTable		1.3.6.1.4.1.248.11.10.1.6.3
This table contains additional information about the interfaces.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hm2IfaceExtEntry

hm2IfaceExtEntry		1.3.6.1.4.1.248.11.10.1.6.3.1
.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hm2IfaceExtEntry

hm2IfaceExtIfRole		1.3.6.1.4.1.248.11.10.1.6.3.1.1
The current role of the interface.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ethernetCsmacd(6), softwareLoopback(24), l3ipvlan(136), ieee8023adLag(161), shdsl(169), ringPort(1001), subringPort(1002), couplingPort(1003), routerPort(1004), probePort(1005), cpuPort(1006), servicePort(1007), outOfBandMgmtPort(1008), lagMember(1101), lreMember(1102), lreInterface(1201), ringLagInterface(1202)

hm2SfpInfoTable		1.3.6.1.4.1.248.11.10.1.7.1
This table contains variables for each SFP.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hm2SfpInfoEntry

hm2SfpInfoEntry		1.3.6.1.4.1.248.11.10.1.7.1.1
Entry for a detected SFP.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hm2SfpInfoEntry

hm2SfpModuleType		1.3.6.1.4.1.248.11.10.1.7.1.1.1
Type of the module. SFP or SFP+ (3), XFP (6).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	sfp(3), xfp(6)

hm2SfpMediaType		1.3.6.1.4.1.248.11.10.1.7.1.1.2
The SFP's Media Type
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ge-1000-base-sx(1), ge-1000-base-lx(2), ge-1000-base-cx(4), fe-100base-lx(5), fe-100base-fx(6), ge-1000-base-t(8), unsupported(9), oc3-mm-sr(10), oc3-sm-ir(11), oc3-sm-lr(12), oc12-mm-sr(13), oc12-sm-ir(14), oc12-sm-lr(15), oc48-sr(16), oc48-ir(17), oc48-lr(18), xfp-10gbase-sr(30), xfp-10gbase-lr(31), xfp-10gbase-er(32), microfx(40), pof(41), m-sfp-2500(50)

hm2SfpConnector		1.3.6.1.4.1.248.11.10.1.7.1.1.3
The SFP's Connector Type.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	nonSfp(1), fiberjack(6), lc(7), mtrj(8), opticalPigtail(11), copperPigtail(33), rj45(34), vendorSpecific(128)

hm2SfpVendorName		1.3.6.1.4.1.248.11.10.1.7.1.1.4
The SFP's vendor name (ASCII).
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString

hm2SfpVendorOUI		1.3.6.1.4.1.248.11.10.1.7.1.1.5
The vendor organizationally unique identifier field (OUI).
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

hm2SfpPartNumber		1.3.6.1.4.1.248.11.10.1.7.1.1.6
The part number of the module (ASCII).
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString

hm2SfpPartRev		1.3.6.1.4.1.248.11.10.1.7.1.1.7
The revision number of the module (ASCII).
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString

hm2SfpSerialNum		1.3.6.1.4.1.248.11.10.1.7.1.1.8
The SFP's serial number provided by vendor (ASCII).
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString

hm2SfpDateCode		1.3.6.1.4.1.248.11.10.1.7.1.1.9
The SFP's vendor manufacturing date code. Format is YY:MM:DD.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString

hm2SfpInfoVersion		1.3.6.1.4.1.248.11.10.1.7.1.1.10
Version of SFP's Hirschmann information. Contains -1 in case of a device read error.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hm2SfpInfoPartNumber		1.3.6.1.4.1.248.11.10.1.7.1.1.11
Part Number of SFP's Hirschmann information.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString	Size(0..11)

hm2SfpInfoPartId		1.3.6.1.4.1.248.11.10.1.7.1.1.12
Part Identifier of SFP's Hirschmann information.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString	Size(0..16)

hm2SfpBitRateNominal		1.3.6.1.4.1.248.11.10.1.7.1.1.13
The SFP's nominal bitrate in units of MBits/sec. Contains -1 in case of a device read error.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hm2SfpBitRateMin		1.3.6.1.4.1.248.11.10.1.7.1.1.14
The minimum bit rate is specified in units of 100 Megabits per second, rounded off to the nearest 100 Megabits per second. A value of 0 indicates that the minimum bit rate is not specified.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hm2SfpBitRateMax		1.3.6.1.4.1.248.11.10.1.7.1.1.15
The maximum bit rate is specified in units of 100 Megabits per second, rounded off to the nearest 100 Megabits per second. A value of 0 indicates that the maximum bit rate is not specified.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hm2SfpMaxLength-fiber-9		1.3.6.1.4.1.248.11.10.1.7.1.1.16
Max. usable length for the cable type '9/125 micrometer fiber' with this SFP in units of meters.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hm2SfpMaxLength-fiber-50		1.3.6.1.4.1.248.11.10.1.7.1.1.17
Max. usable length for the cable type '50/125 micrometer fiber' with this SFP in units of meters.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hm2SfpMaxLength-fiber-e50		1.3.6.1.4.1.248.11.10.1.7.1.1.18
Max. usable length for the cable type 'EBW 50/125 micrometer fiber' with this SFP in units of meters or -1 if not supported.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hm2SfpMaxLength-fiber-62-5		1.3.6.1.4.1.248.11.10.1.7.1.1.19
Max. usable length for the cable type '62.5/125 micrometer fiber' with this SFP in units of meters.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hm2SfpMaxLength-copper		1.3.6.1.4.1.248.11.10.1.7.1.1.20
Max. usable length for the cable type 'copper' with this SFP in units of meters.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hm2SfpWaveLength		1.3.6.1.4.1.248.11.10.1.7.1.1.21
Nominal transmitter output wavelength at room temperature. The laser wavelength in nm (units of 0.05nm).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hm2SfpWaveLengthTolerance		1.3.6.1.4.1.248.11.10.1.7.1.1.22
The +/- range of transmitter output wavelength under normal operating conditions or -1 if not supported.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hm2SfpEnhancedOptions		1.3.6.1.4.1.248.11.10.1.7.1.1.23
Not supported.
Status: current	Access: read-only
OBJECT-TYPE
	BITS	none(0)

hm2SfpSupported		1.3.6.1.4.1.248.11.10.1.7.1.1.24
The SFP is supported by the device (true) or not (false).
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

hm2SfpSupportedReason		1.3.6.1.4.1.248.11.10.1.7.1.1.25
The reason why this SFP is supported.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	hirschmannID(1), whiteList(2), wrongSpeed(3), noneEthernet(4), tpSfpNotSupported(5)

hm2SfpDiagTable		1.3.6.1.4.1.248.11.10.1.7.2
This table contains variables for each SFP.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hm2SfpDiagEntry

hm2SfpDiagEntry		1.3.6.1.4.1.248.11.10.1.7.2.1
Entry for a detected SFP.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hm2SfpDiagEntry

hm2SfpCurrentBitRate		1.3.6.1.4.1.248.11.10.1.7.2.1.1
The current bit rate in units of Megabits per second.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hm2SfpCurrentTemperature		1.3.6.1.4.1.248.11.10.1.7.2.1.2
This signed integer is used to identify the temperature within the SFP in units of centigrade (Celsius). Contains -1000 in case of a device read error.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hm2SfpCurrentTxPower		1.3.6.1.4.1.248.11.10.1.7.2.1.3
The SFP's internally measured Tx Power in units of 1/10 microwatt or -1 if it is not supported.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hm2SfpCurrentRxPower		1.3.6.1.4.1.248.11.10.1.7.2.1.4
The SFP's internally measured Rx Power in units of 1/10 microWatts or -10000 if not supportted.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hm2SfpCurrentTxPowerdBm		1.3.6.1.4.1.248.11.10.1.7.2.1.5
The SFP's internally measured Tx Power in units of dBm. (ASCII representation of a floating point number). - if not supported.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString

hm2SfpCurrentRxPowerdBm		1.3.6.1.4.1.248.11.10.1.7.2.1.6
The SFP's internally measured Rx Power in units of dBm. (ASCII representation of a floating point number). - if not supported.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString

hm2SfpCurrentRxPowerState		1.3.6.1.4.1.248.11.10.1.7.2.1.7
The state of the SFP's internally measured Rx.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ok(1), warning(2), alarm(3), unsupported(4)

hm2SfpWLGroup		1.3.6.1.4.1.248.11.10.1.7.3
OBJECT IDENTIFIER

hm2SfpWLStatus		1.3.6.1.4.1.248.11.10.1.7.3.1
Status of the SFP White List. present(1): a white list is present on the device absent(2): no white list is present on the device not-supported(3): white list feature is not supported in this device
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	present(1), absent(2), not-supported(3)

hm2SfpThresholdTable		1.3.6.1.4.1.248.11.10.1.7.4
This table contains the thresholds for each SFP.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hm2SfpThresholdEntry

hm2SfpThresholdEntry		1.3.6.1.4.1.248.11.10.1.7.4.1
Entry for a detected SFP.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hm2SfpThresholdEntry

hm2SfpTemperatureHighAlarm		1.3.6.1.4.1.248.11.10.1.7.4.1.1
The SFP's Temperature High Alarm threshold in units of centigrade (Celsius). It is -1000 if the SFP device does not support it or in case of a device read error.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hm2SfpTemperatureHighWarning		1.3.6.1.4.1.248.11.10.1.7.4.1.2
The SFP's Temperature High Warning threshold in units of centigrade (Celsius). It is -1000 if the SFP device does not support it or in case of a device read error.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hm2SfpTemperatureLowAlarm		1.3.6.1.4.1.248.11.10.1.7.4.1.3
The SFP's Temperature Low Alarm threshold in units of centigrade (Celsius). It is -1000 if the SFP device does not support it or in case of a device read error.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hm2SfpTemperatureLowWarning		1.3.6.1.4.1.248.11.10.1.7.4.1.4
The SFP's Temperature Low Warning threshold in units of centigrade (Celsius). It is -1000 if the SFP device does not support it or in case of a device read error.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hm2SfpTxPowerHighAlarm		1.3.6.1.4.1.248.11.10.1.7.4.1.5
The SFP's Tx Power High Alarm threshold in units of 0.1uW. It is -10000 if the SFP device does not support it or in case of a device read error.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hm2SfpTxPowerHighWarning		1.3.6.1.4.1.248.11.10.1.7.4.1.6
The SFP's Tx Power High Warning threshold in units of 0.1uW. It is -10000 if the SFP device does not support it or in case of a device read error.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hm2SfpTxPowerLowAlarm		1.3.6.1.4.1.248.11.10.1.7.4.1.7
The SFP's Tx Power Low Alarm threshold in units of 0.1uW. It is -10000 if the SFP device does not support it or in case of a device read error.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hm2SfpTxPowerLowWarning		1.3.6.1.4.1.248.11.10.1.7.4.1.8
The SFP's Tx Power Low Warning threshold in units of 0.1uW. It is -10000 if the SFP device does not support it or in case of a device read error.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hm2SfpRxPowerHighAlarm		1.3.6.1.4.1.248.11.10.1.7.4.1.9
The SFP's Rx Power High Alarm threshold in units of 0.1uW. It is -10000 if the SFP device does not support it or in case of a device read error.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hm2SfpRxPowerHighWarning		1.3.6.1.4.1.248.11.10.1.7.4.1.10
The SFP's Rx Power High Warning threshold in units of 0.1uW. It is -10000 if the SFP device does not support it or in case of a device read error.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hm2SfpRxPowerLowAlarm		1.3.6.1.4.1.248.11.10.1.7.4.1.11
The SFP's Rx Power Low Alarm threshold in units of 0.1uW. It is -10000 if the SFP device does not support it or in case of a device read error.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hm2SfpRxPowerLowWarning		1.3.6.1.4.1.248.11.10.1.7.4.1.12
The SFP's Rx Power Low Warning threshold in units of 0.1uW. It is -10000 if the SFP device does not support it or in case of a device read error.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hm2SfpTxPowerdBmHighAlarm		1.3.6.1.4.1.248.11.10.1.7.4.1.13
The SFP's Tx Power High Alarm threshold in units of dBm (ASCII representation of floating point number). It is N/A if the SFP device does not support it or in case of a device read error.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString

hm2SfpTxPowerdBmHighWarning		1.3.6.1.4.1.248.11.10.1.7.4.1.14
The SFP's Tx Power High Warning threshold in units of dBm (ASCII representation of floating point number). It is N/A if the SFP device does not support it or in case of a device read error.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString

hm2SfpTxPowerdBmLowAlarm		1.3.6.1.4.1.248.11.10.1.7.4.1.15
The SFP's Tx Power Low Alarm threshold in units of dBm (ASCII representation of floating point number). It is N/A if the SFP device does not support it or in case of a device read error.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString

hm2SfpTxPowerdBmLowWarning		1.3.6.1.4.1.248.11.10.1.7.4.1.16
The SFP's Tx Power Low Warning threshold in units of dBm (ASCII representation of floating point number). It is N/A if the SFP device does not support it or in case of a device read error.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString

hm2SfpRxPowerdBmHighAlarm		1.3.6.1.4.1.248.11.10.1.7.4.1.17
The SFP's Rx Power High Alarm threshold in units of dBm (ASCII representation of floating point number). It is N/A if the SFP device does not support it or in case of a device read error.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString

hm2SfpRxPowerdBmHighWarning		1.3.6.1.4.1.248.11.10.1.7.4.1.18
The SFP's Rx Power High Warning threshold in units of dBm (ASCII representation of floating point number). It is N/A if the SFP device does not support it or in case of a device read error.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString

hm2SfpRxPowerdBmLowAlarm		1.3.6.1.4.1.248.11.10.1.7.4.1.19
The SFP's Rx Power Low Alarm threshold in units of dBm (ASCII representation of floating point number). It is N/A if the SFP device does not support it or in case of a device read error.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString

hm2SfpRxPowerdBmLowWarning		1.3.6.1.4.1.248.11.10.1.7.4.1.20
The SFP's Rx Power Low Warning threshold in units of dBm (ASCII representation of floating point number). It is N/A if the SFP device does not support it or in case of a device read error.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString

hm2ExtNvmGeneralGroup		1.3.6.1.4.1.248.11.10.1.8.1
OBJECT IDENTIFIER

hm2ExtNvmChooseActive		1.3.6.1.4.1.248.11.10.1.8.1.1
The user can choose which external NV memory to use for file operations.
Status: current	Access: read-write
OBJECT-TYPE
	Hm2DeviceExtNVMType

hm2ExtNvmLogDevice		1.3.6.1.4.1.248.11.10.1.8.1.2
The user can choose which external NV memory to use for persistent logging.
Status: current	Access: read-write
OBJECT-TYPE
	Hm2DeviceExtNVMType

hm2ExtNvmAdminMode		1.3.6.1.4.1.248.11.10.1.8.1.3
Switches the USB bus between High Speed (normal) and Full Speed (compatibility). This setting only takes effect after a reboot.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	normal(1), compatibility(2)

hm2ExtNvmOperMode		1.3.6.1.4.1.248.11.10.1.8.1.4
Shows the USB mode the device is currently operating in.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	normal(1), compatibility(2)

hm2ExtNvmTable		1.3.6.1.4.1.248.11.10.1.8.2
This table contains variables for each nvram.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hm2ExtNvmEntry

hm2ExtNvmEntry		1.3.6.1.4.1.248.11.10.1.8.2.1
Entry for an external nvram.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hm2ExtNvmEntry

hm2ExtNvmTableIndex		1.3.6.1.4.1.248.11.10.1.8.2.1.1
Index
Status: current	Access: not-accessible
OBJECT-TYPE
	Hm2DeviceExtNVMType

hm2ExtNvmStatus		1.3.6.1.4.1.248.11.10.1.8.2.1.2
Status of the external non-volatile memory. notPresent(1): external non-volatile memory has not been detected. removed(2): external non-volatile memory was removed in running mode of the agent. ok(3): external non-volatile memory is present and OK. outOfMemory(4): external non-volatile memory is full. genericErr(5): Any other failure, e.g. hardware malfunction.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notPresent(1), removed(2), ok(3), outOfMemory(4), genericErr(5)

hm2ExtNvmManufacturerId		1.3.6.1.4.1.248.11.10.1.8.2.1.3
The manufacturer ID.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

hm2ExtNvmHWRevision		1.3.6.1.4.1.248.11.10.1.8.2.1.4
The application ID.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

hm2ExtNvmProductName		1.3.6.1.4.1.248.11.10.1.8.2.1.5
The product name.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

hm2ExtNvmVersion		1.3.6.1.4.1.248.11.10.1.8.2.1.6
The version.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

hm2ExtNvmSerialNum		1.3.6.1.4.1.248.11.10.1.8.2.1.7
The serial number provided by vendor (ASCII).
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

hm2ExtNvmAutomaticSoftwareLoad		1.3.6.1.4.1.248.11.10.1.8.2.1.8
Enable or disable Automatic loading of a software image from the external non-volatile memory. A file named 'startup.txt' must be present on the external non-volatile memory and contain the line 'autoUpdate=filename'.
Status: current	Access: read-write
OBJECT-TYPE
	HmEnabledStatus

hm2ExtNvmConfigLoadPriority		1.3.6.1.4.1.248.11.10.1.8.2.1.9
Set the priority of this external non-volatile memory for loading the configuration while booting. The configuration on the device with the lowest priority is loaded. Setting this variable to 0 disables loading of a configuration from this device.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(0), first(1), second(2), third(3)

hm2ExtNvmConfigSave		1.3.6.1.4.1.248.11.10.1.8.2.1.10
Enable or disable Automatic saving of the configuration to the external non-volatile memory. If this is enabled, saving the configuration of the device to its internal nvram also stores in on this external nvram.
Status: current	Access: read-write
OBJECT-TYPE
	HmEnabledStatus

hm2ExtNvmWritable		1.3.6.1.4.1.248.11.10.1.8.2.1.11
Shows if writing to the device is possible, i.e. if it is write protected.
Status: current	Access: read-only
OBJECT-TYPE
	HmEnabledStatus

hm2ExtNvmAutomaticSshKeyLoad		1.3.6.1.4.1.248.11.10.1.8.2.1.12
Enable or disable automatic loading of a SSH key from the external non-volatile memory. A file named 'startup.txt' must be present on the external non-volatile memory and contain the line 'autoUpdateRSA=' and/or 'autoUpdateDSA='.
Status: current	Access: read-write
OBJECT-TYPE
	HmEnabledStatus

hm2AutoDisableIntfTable		1.3.6.1.4.1.248.11.10.1.9.1
Port Auto Disable interface table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hm2AutoDisableIntfEntry

hm2AutoDisableIntfEntry		1.3.6.1.4.1.248.11.10.1.9.1.1
Port Auto Disable interface entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hm2AutoDisableIntfEntry

hm2AutoDisableIntfRemainingTime		1.3.6.1.4.1.248.11.10.1.9.1.1.1
Remaining time in seconds until the re-activation of the port.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hm2AutoDisableIntfComponentName		1.3.6.1.4.1.248.11.10.1.9.1.1.2
Name of the component that triggered the error
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString

hm2AutoDisableIntfErrorReason		1.3.6.1.4.1.248.11.10.1.9.1.1.3
Error disable reason
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(0), link-flap(1), crc-error(2), duplex-mismatch(3), dhcp-snooping(4), arp-rate(5), bpdu-rate(6), mac-based-port-security(7), overload-detection(8), speed-duplex(9)

hm2AutoDisableIntfTimer		1.3.6.1.4.1.248.11.10.1.9.1.1.4
Timer value in seconds after a deactivated port is activated again. Possible values are: 30-4294967295. A value of 0 disables the timer.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	0 \| 30..4294967295

hm2AutoDisableIntfReset		1.3.6.1.4.1.248.11.10.1.9.1.1.5
Port Auto Disable interface reset.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

hm2AutoDisableIntfOperState		1.3.6.1.4.1.248.11.10.1.9.1.1.6
Status of Auto Disable interface admin state. Active means that a component has encountered an error and Auto-Disable has turned off the interface. Inactive means that currently there is no error
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	active(1), inactive(2)

hm2AutoDisableIntfErrorTime		1.3.6.1.4.1.248.11.10.1.9.1.1.7
Local system time (hm2SystemLocalTime) when the error occured.
Status: current	Access: read-only
OBJECT-TYPE
	HmTimeSeconds1970

hm2AutoDisableReasonTable		1.3.6.1.4.1.248.11.10.1.9.2
Possible reasons for Auto Disable
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hm2AutoDisableReasonEntry

hm2AutoDisableReasonEntry		1.3.6.1.4.1.248.11.10.1.9.2.1
Port Auto Disable interface entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hm2AutoDisableReasonEntry

hm2AutoDisableReasons		1.3.6.1.4.1.248.11.10.1.9.2.1.1
Reason for deactivation a port
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	link-flap(1), crc-error(2), duplex-mismatch(3), dhcp-snooping(4), arp-rate(5), bpdu-rate(6), mac-based-port-security(7), overload-detection(8), speed-duplex(9)

hm2AutoDisableReasonOperation		1.3.6.1.4.1.248.11.10.1.9.2.1.2
Enables/disables recovery by resaon on this device.
Status: current	Access: read-write
OBJECT-TYPE
	HmEnabledStatus

hm2AutoDisableReasonCategory		1.3.6.1.4.1.248.11.10.1.9.2.1.3
Auto Disable Reason Category
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	other(1), port-monitor(2), network-security(3), l2-redundancy(4)

hm2UnitTable		1.3.6.1.4.1.248.11.10.1.10.100
This table contains unit capabilities and configuration options.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hm2UnitEntry

hm2UnitEntry		1.3.6.1.4.1.248.11.10.1.10.100.1
Entry with the configuration options and supported features of a unit.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hm2UnitEntry

hm2UnitIndex		1.3.6.1.4.1.248.11.10.1.10.100.1.1
The index of the available unit.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

hm2UnitMaxModuleCapacity		1.3.6.1.4.1.248.11.10.1.10.100.1.2
Maximum number of modules that this unit can contain in this system.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hm2UnitMaxModulePortCapacity		1.3.6.1.4.1.248.11.10.1.10.100.1.3
Maximum number of ports that a module can contain in this unit.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hm2ModuleTable		1.3.6.1.4.1.248.11.10.1.11.100
This table contains capabilities and configuration options of device modules.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hm2ModuleEntry

hm2ModuleEntry		1.3.6.1.4.1.248.11.10.1.11.100.1
Entry with the configuration options and supported features of a device module.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hm2ModuleEntry

hm2ModuleIndex		1.3.6.1.4.1.248.11.10.1.11.100.1.1
The index of the available module.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

hm2ModuleId		1.3.6.1.4.1.248.11.10.1.11.100.1.2
Manufacturer-defined product identifier (module family + product ID). Example: Object-ID 1.3.6.1.4.1.248.11.2.2.1 is the hm2ModuleFamily MSM and Object-ID 1.3.6.1.4.1.248.11.2.2.1.1 is the Product ID for msm-4tx
Status: current	Access: read-only
OBJECT-TYPE
	OBJECT IDENTIFIER

hm2ModuleDescription		1.3.6.1.4.1.248.11.10.1.11.100.1.3
Description of the module. This value cannot be written by external entities (only for internal purposes).
Status: current	Access: read-write
OBJECT-TYPE
	SnmpAdminString

hm2ModuleProductCode		1.3.6.1.4.1.248.11.10.1.11.100.1.4
Product Code of the module.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString

hm2ModuleVersion		1.3.6.1.4.1.248.11.10.1.11.100.1.5
Version of the module.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString

hm2ModuleNumOfPorts		1.3.6.1.4.1.248.11.10.1.11.100.1.6
The numberOfPorts is the number of ports contained within the module. Within each module, the ports are uniquely numbered in the range from 1 to numberOfPorts.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hm2ModuleFirstMauIndex		1.3.6.1.4.1.248.11.10.1.11.100.1.7
Value of the first mauIndex used by the module. NOTE: This object is obsolete in favour of hm2ModuleFirstIfIndex.
Status: obsolete	Access: read-only
OBJECT-TYPE
	Integer32

hm2ModuleStatus		1.3.6.1.4.1.248.11.10.1.11.100.1.8
Status of the module. If the value is physical(1), then the module is plugged in, if the value is configurable, the ports can be configured, but the card is absent, with the value remove(3) written to the agent the card can be logically removed. The value fix(4) is for modules which cannot be removed.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	physical(1), configurable(2), remove(3), fix(4)

hm2ModuleSerialNum		1.3.6.1.4.1.248.11.10.1.11.100.1.9
The serial number provided by vendor (ASCII).
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString

hm2ModuleMinSWVersion		1.3.6.1.4.1.248.11.10.1.11.100.1.10
The minimum software version required to support this module.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hm2ModuleCapability		1.3.6.1.4.1.248.11.10.1.11.100.1.11
poe - module supports Power over Ethernet, fpga - module has a FPGA, ptp - module supports PTP, io-module - module is an IO module. This value cannot be written by external entities (only for internal purposes).
Status: current	Access: read-write
OBJECT-TYPE
	BITS	poe(0), fpga(1), ptp(2), io-module(3)

hm2ModuleInternalID		1.3.6.1.4.1.248.11.10.1.11.100.1.12
An internal ID of the Module. This value cannot be written by external entities (only for internal purposes).
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

hm2ModuleInternalIDVariant		1.3.6.1.4.1.248.11.10.1.11.100.1.13
An internal variant ID of the Module. NOTE: This object is obsolete.
Status: obsolete	Access: read-write
OBJECT-TYPE
	Integer32

hm2ModuleFirstIfIndex		1.3.6.1.4.1.248.11.10.1.11.100.1.14
Value of the first ifIndex used by the module.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hm2ModuleAdminState		1.3.6.1.4.1.248.11.10.1.11.100.1.15
Enable or disable the module. If disabled, module plugged in this slot will not be activated.
Status: current	Access: read-write
OBJECT-TYPE
	HmEnabledStatus

hm2SfpChangeTrap		1.3.6.1.4.1.248.11.10.0.1
This trap is sent when a SFP has been added or removed. It is also sent for an otherwise unsupported SFP.
Status: current	Access: read-write
NOTIFICATION-TYPE

hm2AutoDisablePortTrap		1.3.6.1.4.1.248.11.10.0.2
This trap is sent if the port has been disabled or enabled by auto disable feature.
Status: current	Access: read-write
NOTIFICATION-TYPE

hm2ModulePluggedTrap		1.3.6.1.4.1.248.11.10.0.3
This trap is sent if a module is plugged into a unit.
Status: current	Access: read-write
NOTIFICATION-TYPE

hm2ModuleRemovedTrap		1.3.6.1.4.1.248.11.10.0.4
This trap is sent if a module is removed from a unit.
Status: current	Access: read-write
NOTIFICATION-TYPE

hm2SFPRxPowerChangeTrap		1.3.6.1.4.1.248.11.10.0.5
This trap is sent when the state (hm2SfpCurrentRxPowerState) of the rx power of a SFP changes.
Status: current	Access: read-write
NOTIFICATION-TYPE