SONOMASYSTEMS-SONOMA-ATM-GENERIC-MIB

File: SONOMASYSTEMS-SONOMA-ATM-GENERIC-MIB.mib (64040 bytes)

Imported modules

RFC1155-SMI RFC-1212 SONOMASYSTEMS-SONOMA-MIB

Imported symbols

Counter OBJECT-TYPE sonomaATM

Defined Types

AtmGenPhysEntry  
SEQUENCE    
  atmGenPhysIndex INTEGER
  atmGenPhysAal5Mtu INTEGER
  atmGenPhysAal5CrcErrors Counter
  atmGenPhysAal5OverSizedSDUs Counter
  atmGenPhysAal5DiscardPDU Counter
  atmGenPhysHECErrors Counter
  atmGenPhysUnknownProtocols Counter
  atmGenPhysCellsReceived Counter
  atmGenPhysCellsTransmitted Counter
  atmGenPhysRxBufStarvation Counter
  atmGenPhysRxFreeze Counter
  atmGenPhysTxFreeze Counter

AtmGenRateEntry  
SEQUENCE    
  atmGenRatePhysIndex INTEGER
  atmGenRateQueOne INTEGER
  atmGenRateQueTwo INTEGER
  atmGenRateQueThree INTEGER
  atmGenRateQueFour INTEGER
  atmGenRateQueFive INTEGER
  atmGenRateQueSix INTEGER
  atmGenRateQueSeven INTEGER
  atmGenRateQueEight INTEGER

AtmGenRateQEntry  
SEQUENCE    
  atmGenRateQPhysIndex INTEGER
  atmGenRateQNumber INTEGER
  atmGenRateQueue INTEGER

AtmGenVclEntry  
SEQUENCE    
  atmGenVclIfIndex INTEGER
  atmGenVclVpi INTEGER
  atmGenVclVci INTEGER
  atmGenVclRateQ INTEGER
  atmGenVclAction INTEGER

AtmGenVclTmEntry  
SEQUENCE    
  atmGenVclTmIfIndex INTEGER
  atmGenVclTmVpi INTEGER
  atmGenVclTmVci INTEGER
  atmGenVclTmPCR INTEGER
  atmGenVclTmSCR INTEGER
  atmGenVclTmMBS INTEGER
  atmGenVclTmAction INTEGER

AtmGenVclStatsEntry  
SEQUENCE    
  atmGenVclStatsIfIndex INTEGER
  atmGenVclStatsVpi INTEGER
  atmGenVclStatsVci INTEGER
  atmGenVclStatsCellsReceived Counter
  atmGenVclStatsCellsTransmitted Counter
  atmGenVclStatsOamAisRcvCells Counter
  atmGenVclStatsOamAisXmtCells Counter
  atmGenVclStatsOamRdiRcvCells Counter
  atmGenVclStatsOamRdiXmtCells Counter
  atmGenVclStatsOamLoopbackRcvCells Counter
  atmGenVclStatsOamLoopbackXmtCells Counter

AtmGenLogicalPortEntry  
SEQUENCE    
  atmGenLpIfIndex INTEGER
  atmGenLpPhysIf INTEGER
  atmGenLpLoopTime INTEGER
  atmGenLpProtocol INTEGER
  atmGenLpAal5EncapsType INTEGER
  atmGenLpAal5Mtu INTEGER
  atmGenLpAal5RateQ INTEGER
  atmGenLpAdminStatus INTEGER
  atmGenLpLoopThreshold INTEGER
  atmGenLpLoopTrapTime INTEGER
  atmGenLpOamGeneration INTEGER

CesConfEntry  
SEQUENCE    
  cesAtmPhysPort INTEGER
  cesAtmVpi INTEGER
  cesAtmVci INTEGER
  cesCbrService INTEGER
  cesCbrClockMode INTEGER
  cesCas INTEGER
  cesPartialFill INTEGER
  cesBufMaxSize INTEGER
  cesCdvRxT INTEGER
  cesCellLossIntegrationPeriod INTEGER
  cesConnType INTEGER
  cesDynBw INTEGER
  cesSigType INTEGER
  cesConfAction INTEGER

CesStatsEntry  
SEQUENCE    
  cesStatsAtmPhyPort INTEGER
  cesStatsAtmVpi INTEGER
  cesStatsAtmVci INTEGER
  cesReassCells Counter
  cesHdrErrors Counter
  cesPointerReframes Counter
  cesPointerParityErrors Counter
  cesAal1SeqErrors Counter
  cesLostCells Counter
  cesMisinsertedCells Counter
  cesBufUnderflows Counter
  cesBufOverflows Counter
  cesCellLossStatus INTEGER

CesAttachmentEntry  
SEQUENCE    
  cesAttachmentPhysPort INTEGER
  cesAttachmentBundle INTEGER
  cesAttachmentChan INTEGER
  cesAttachmentAction INTEGER

AtmAsiConfPhyEntry  
SEQUENCE    
  atmAsiConfPhysIndex INTEGER
  atmAsiConfLineType INTEGER
  atmAsiConfLineCoding INTEGER
  atmAsiConfTxClkSelect INTEGER
  atmAsiConfSignalMode INTEGER
  atmAsiConfLIUType INTEGER
  atmAsiConfLBOType INTEGER
  atmAsiConfIdlePattern INTEGER
  atmAsiConfLoopbackMode INTEGER
  atmAsiConfStopMode INTEGER
  atmAsiConfRecoveredClkSource INTEGER
  atmAsiDebugAddr INTEGER
  atmAsiDebugReadValue INTEGER
  atmAsiDebugWriteValue INTEGER
  atmAsiDebugRead INTEGER

AtmAsiStatsEntry  
SEQUENCE    
  atmAsiStatsPhysIndex INTEGER
  atmAsiStatsNoSignals Counter
  atmAsiStatsAISDetects Counter
  atmAsiStatsYelAlarmCount Counter
  atmAsiStatsLCVErrors Counter
  atmAsiStatsPCVErrors Counter
  atmAsiStatsMOSErrors Counter
  atmAsiStatsSyncLossCount Counter
  atmAsiStatsHECErrors Counter
  atmAsiStatsSignalLoss INTEGER
  atmAsiStatsAISDetect INTEGER
  atmAsiStatsYellowAlarm INTEGER
  atmAsiStatsSyncLoss INTEGER
  atmAsiStatsTxClockLoss INTEGER
  atmAsiStatsClearCounters INTEGER

AtmAsmPhyConfEntry  
SEQUENCE    
  atmAsmPhyConfIndex INTEGER
  atmAsmPhyConfAdminLineUsage INTEGER
  atmAsmPhyConfOperLineUsage INTEGER

Defined Values

sonomaGenericATMGroup 1.3.6.1.4.1.2926.25.7.1
OBJECT IDENTIFIER    

atmGenericPhysGroup 1.3.6.1.4.1.2926.25.7.1.1
OBJECT IDENTIFIER    

atmGenericVclGroup 1.3.6.1.4.1.2926.25.7.1.2
OBJECT IDENTIFIER    

atmGenericLpGroup 1.3.6.1.4.1.2926.25.7.1.3
OBJECT IDENTIFIER    

atmCesGroup 1.3.6.1.4.1.2926.25.7.1.4
OBJECT IDENTIFIER    

atmAsiPhysGroup 1.3.6.1.4.1.2926.25.7.1.5
OBJECT IDENTIFIER    

atmAsmPhysGroup 1.3.6.1.4.1.2926.25.7.1.6
OBJECT IDENTIFIER    

atmGenPhysTable 1.3.6.1.4.1.2926.25.7.1.1.1
A table of physical layer status and parameter information for the UNI's physical interface
OBJECT-TYPE    
  SEQUENCE OF  
    AtmGenPhysEntry

atmGenPhysEntry 1.3.6.1.4.1.2926.25.7.1.1.1.1
A entry in the table, containing information about the physical layer of a UNI interface
OBJECT-TYPE    
  AtmGenPhysEntry  

atmGenPhysIndex 1.3.6.1.4.1.2926.25.7.1.1.1.1.1
The physical interface instance.
OBJECT-TYPE    
  INTEGER  

atmGenPhysAal5Mtu 1.3.6.1.4.1.2926.25.7.1.1.1.1.2
The AAL5 MTU capacity for the physical interface, assigned by PM.
OBJECT-TYPE    
  INTEGER  

atmGenPhysAal5CrcErrors 1.3.6.1.4.1.2926.25.7.1.1.1.1.3
The total number of AAL5 CPCS PDUs received with CRC-32 errors at the interface associated with an AAL5 entity.
OBJECT-TYPE    
  Counter  

atmGenPhysAal5OverSizedSDUs 1.3.6.1.4.1.2926.25.7.1.1.1.1.4
The total number of AAL5 CPCS PDUs discarded at the interface associated with an AAL5 entity because the AAL5 SDUs were too large.
OBJECT-TYPE    
  Counter  

atmGenPhysAal5DiscardPDU 1.3.6.1.4.1.2926.25.7.1.1.1.1.5
The total number of AAL5 CPCS PDUs discarded at the interface associated with an AAL5 entity because no receive free buffers were available. Only available with TCOP atm card.
OBJECT-TYPE    
  Counter  

atmGenPhysHECErrors 1.3.6.1.4.1.2926.25.7.1.1.1.1.6
The total number ATM cells dropped out to HEC errors. Only available with TCOP atm card.
OBJECT-TYPE    
  Counter  

atmGenPhysUnknownProtocols 1.3.6.1.4.1.2926.25.7.1.1.1.1.7
The total number cells received with an unknown header. Only available with TCOP atm card.
OBJECT-TYPE    
  Counter  

atmGenPhysCellsReceived 1.3.6.1.4.1.2926.25.7.1.1.1.1.8
The total number ATM cells received with no errors. Only available with TCOP atm card.
OBJECT-TYPE    
  Counter  

atmGenPhysCellsTransmitted 1.3.6.1.4.1.2926.25.7.1.1.1.1.9
The total number ATM cells actually transmitted. Only available with TCOP atm card.
OBJECT-TYPE    
  Counter  

atmGenPhysRxBufStarvation 1.3.6.1.4.1.2926.25.7.1.1.1.1.10
The total number of occurrences when no Rx free buffer is available at the interface associated with an AAL5 entity.
OBJECT-TYPE    
  Counter  

atmGenPhysRxFreeze 1.3.6.1.4.1.2926.25.7.1.1.1.1.11
The total number of occurrences when Rx completion ring overflows at the interface associated with an AAL5 entity.
OBJECT-TYPE    
  Counter  

atmGenPhysTxFreeze 1.3.6.1.4.1.2926.25.7.1.1.1.1.12
The total number of occurrences when Tx completion ring overflows at the interface associated with an AAL5 entity.
OBJECT-TYPE    
  Counter  

atmGenRateTable 1.3.6.1.4.1.2926.25.7.1.1.2
A table of ATM layer configuration for the ATM-DS3/E3/OC3c interface. Only used by earlier version of software.
OBJECT-TYPE    
  SEQUENCE OF  
    AtmGenRateEntry

atmGenRateEntry 1.3.6.1.4.1.2926.25.7.1.1.2.1
A entry in the table, containing information about the rate queues on this physical interface.
OBJECT-TYPE    
  AtmGenRateEntry  

atmGenRatePhysIndex 1.3.6.1.4.1.2926.25.7.1.1.2.1.1
The ATM interface index, for this table the value of this object corresponds to the physical port instance.
OBJECT-TYPE    
  INTEGER 1..256  

atmGenRateQueOne 1.3.6.1.4.1.2926.25.7.1.1.2.1.2
The value of this object can be set to any value in the range 0 to 30720 for E3, the range 0 to 36864 for DS3, and the range 0 to 135150 for OC3. The combination of all the values of all the rate queue objects must equal 30720 for E3, 36864 for DS3, and 135150 for OC3. Thus, if this object has a value of 36864 for DS3, then the values of the rest of the objects cannot be set to anything other than 0. The value of any rate queue object is rounded down to the nearest multiple of 10.
OBJECT-TYPE    
  INTEGER 0..135150  

atmGenRateQueTwo 1.3.6.1.4.1.2926.25.7.1.1.2.1.3
The ATM layer rate queue number two bandwidth.
OBJECT-TYPE    
  INTEGER 0..135150  

atmGenRateQueThree 1.3.6.1.4.1.2926.25.7.1.1.2.1.4
The ATM layer rate queue number three bandwidth.
OBJECT-TYPE    
  INTEGER 0..135150  

atmGenRateQueFour 1.3.6.1.4.1.2926.25.7.1.1.2.1.5
The ATM layer rate queue number four bandwidth.
OBJECT-TYPE    
  INTEGER 0..135150  

atmGenRateQueFive 1.3.6.1.4.1.2926.25.7.1.1.2.1.6
The ATM layer rate queue number five bandwidth.
OBJECT-TYPE    
  INTEGER 0..135150  

atmGenRateQueSix 1.3.6.1.4.1.2926.25.7.1.1.2.1.7
The ATM layer rate queue number six bandwidth.
OBJECT-TYPE    
  INTEGER 0..135150  

atmGenRateQueSeven 1.3.6.1.4.1.2926.25.7.1.1.2.1.8
The ATM layer rate queue number seven bandwidth.
OBJECT-TYPE    
  INTEGER 0..135150  

atmGenRateQueEight 1.3.6.1.4.1.2926.25.7.1.1.2.1.9
The ATM layer rate queue number eight bandwidth.
OBJECT-TYPE    
  INTEGER 0..135150  

atmGenRateQTable 1.3.6.1.4.1.2926.25.7.1.1.3
A table of ATM layer configuration for the ATM-DS3/E3/OC3c interface. Not used with TCOP atm card.
OBJECT-TYPE    
  SEQUENCE OF  
    AtmGenRateQEntry

atmGenRateQEntry 1.3.6.1.4.1.2926.25.7.1.1.3.1
A entry in the table, containing information about the rate queues on this physical interface.
OBJECT-TYPE    
  AtmGenRateQEntry  

atmGenRateQPhysIndex 1.3.6.1.4.1.2926.25.7.1.1.3.1.1
The ATM interface index, for this table the value of this object corresponds to the physical port instance.
OBJECT-TYPE    
  INTEGER 1..256  

atmGenRateQNumber 1.3.6.1.4.1.2926.25.7.1.1.3.1.2
The ATM layer rate queue number.
OBJECT-TYPE    
  INTEGER 1..255  

atmGenRateQueue 1.3.6.1.4.1.2926.25.7.1.1.3.1.3
The value of this object can be set to any value in the range 0 to 30720 for E3, the range 0 to 36864 for DS3, and the range 0 to 135150 for OC3. The combination of all the values of all the rate queue objects must equal 30720 for E3, 36864 for DS3, and 135150 for OC3. Thus, if this object has a value of 36864 for DS3, then the values of the rest of the objects cannot be set to anything other than 0. The value of any rate queue object is rounded down to the nearest multiple of 10.
OBJECT-TYPE    
  INTEGER 0..135150  

atmGenVclTable 1.3.6.1.4.1.2926.25.7.1.2.1
The Virtual Channel Link (VCL) table. A bi-directional VCL is modeled as one entry in this table.
OBJECT-TYPE    
  SEQUENCE OF  
    AtmGenVclEntry

atmGenVclEntry 1.3.6.1.4.1.2926.25.7.1.2.1.1
An entry in the VCL table. This entry is used to model a bi-directional VCL.
OBJECT-TYPE    
  AtmGenVclEntry  

atmGenVclIfIndex 1.3.6.1.4.1.2926.25.7.1.2.1.1.1
The physical interface instance.
OBJECT-TYPE    
  INTEGER  

atmGenVclVpi 1.3.6.1.4.1.2926.25.7.1.2.1.1.2
The VPI value of the VCL, 0 - 255.
OBJECT-TYPE    
  INTEGER 0..255  

atmGenVclVci 1.3.6.1.4.1.2926.25.7.1.2.1.1.3
The VCI value of the VCL. Minimum value of 32 when VPI is 0 and minimum value of 1 for all other VPI. Maximum value of 1023 for 1561 adapter and maximum value of 4095 for 1575 tcop adapter.
OBJECT-TYPE    
  INTEGER 1..1023  

atmGenVclRateQ 1.3.6.1.4.1.2926.25.7.1.2.1.1.4
The Rate Queue used by this virtual circuit.
OBJECT-TYPE    
  INTEGER 1..255  

atmGenVclAction 1.3.6.1.4.1.2926.25.7.1.2.1.1.5
This object is used to create or delete a row in this table. A set request to add a row to this table need only contain this object's value in the PDU. The row created will be defined by the instance passed with the object identifier. Thus, to add the following entry: Logical Port 257, VP 1, VC 36, send a set request with a var bind containing atmGenVclAction.257.1.36 as the object identifier component and 5 as the value of the value component.
OBJECT-TYPE    
  INTEGER create(5), destroy(6)  

atmGenVclTmTable 1.3.6.1.4.1.2926.25.7.1.2.2
The Virtual Channel Link (VCL) table. A bi-directional VCL is modeled as one entry in this table.
OBJECT-TYPE    
  SEQUENCE OF  
    AtmGenVclTmEntry

atmGenVclTmEntry 1.3.6.1.4.1.2926.25.7.1.2.2.1
An entry in the VCL table. This entry is used to model a bi-directional VCL.
OBJECT-TYPE    
  AtmGenVclTmEntry  

atmGenVclTmIfIndex 1.3.6.1.4.1.2926.25.7.1.2.2.1.1
The physical interface instance.
OBJECT-TYPE    
  INTEGER  

atmGenVclTmVpi 1.3.6.1.4.1.2926.25.7.1.2.2.1.2
The VPI value of the VCL, 0 - 255.
OBJECT-TYPE    
  INTEGER 0..255  

atmGenVclTmVci 1.3.6.1.4.1.2926.25.7.1.2.2.1.3
The VCI value of the VCL. Minimum value of 32 when VPI is 0 and minimum value of 1 for all other VPI. Maximum value of 1023 for 1561 adapter and maximum value of 4095 for 1575 tcop adapter.
OBJECT-TYPE    
  INTEGER 1..4095  

atmGenVclTmPCR 1.3.6.1.4.1.2926.25.7.1.2.2.1.4
Specify Peak Cell Rate.
OBJECT-TYPE    
  INTEGER 0..16777215  

atmGenVclTmSCR 1.3.6.1.4.1.2926.25.7.1.2.2.1.5
Specify Sustainable Cell Rate.
OBJECT-TYPE    
  INTEGER 0..16777215  

atmGenVclTmMBS 1.3.6.1.4.1.2926.25.7.1.2.2.1.6
Specify Maximum Burst Size.
OBJECT-TYPE    
  INTEGER 0..16777215  

atmGenVclTmAction 1.3.6.1.4.1.2926.25.7.1.2.2.1.7
This object is used to create or delete a row in this table. A set request to add a row to this table need only contain this object's value in the PDU. The row created will be defined by the instance passed with the object identifier. Thus, to add the following entry: Logical Port 257, VP 1, VC 36, send a set request with a var bind containing atmGenVclAction.257.1.36 as the object identifier component and 5 as the value of the value if you want to create AAL5 VC.
OBJECT-TYPE    
  INTEGER create(5), destroy(6)  

atmGenVclStatsTable 1.3.6.1.4.1.2926.25.7.1.2.3
The Virtual Channel Link (VCL) table. A bi-directional VCL is modeled as one entry in this table.
OBJECT-TYPE    
  SEQUENCE OF  
    AtmGenVclStatsEntry

atmGenVclStatsEntry 1.3.6.1.4.1.2926.25.7.1.2.3.1
An entry in the VCL table.
OBJECT-TYPE    
  AtmGenVclStatsEntry  

atmGenVclStatsIfIndex 1.3.6.1.4.1.2926.25.7.1.2.3.1.1
The physical interface instance.
OBJECT-TYPE    
  INTEGER  

atmGenVclStatsVpi 1.3.6.1.4.1.2926.25.7.1.2.3.1.2
The VPI value of the VCL, 0 - 255.
OBJECT-TYPE    
  INTEGER 0..255  

atmGenVclStatsVci 1.3.6.1.4.1.2926.25.7.1.2.3.1.3
The VCI value of the VCL, 35 - 1023.
OBJECT-TYPE    
  INTEGER 35..1023  

atmGenVclStatsCellsReceived 1.3.6.1.4.1.2926.25.7.1.2.3.1.4
The total number of cells received by this virtual circuit.
OBJECT-TYPE    
  Counter  

atmGenVclStatsCellsTransmitted 1.3.6.1.4.1.2926.25.7.1.2.3.1.5
The total number of cells transmitted by this virtual circuit.
OBJECT-TYPE    
  Counter  

atmGenVclStatsOamAisRcvCells 1.3.6.1.4.1.2926.25.7.1.2.3.1.6
The total number of AIS OAM cells received by this virtual circuit.
OBJECT-TYPE    
  Counter  

atmGenVclStatsOamAisXmtCells 1.3.6.1.4.1.2926.25.7.1.2.3.1.7
The total number of AIS OAM cells transmitted by this virtual circuit.
OBJECT-TYPE    
  Counter  

atmGenVclStatsOamRdiRcvCells 1.3.6.1.4.1.2926.25.7.1.2.3.1.8
The total number of RDI OAM cells received by this virtual circuit.
OBJECT-TYPE    
  Counter  

atmGenVclStatsOamRdiXmtCells 1.3.6.1.4.1.2926.25.7.1.2.3.1.9
The total number of RDI OAM cells transmitted by this virtual circuit.
OBJECT-TYPE    
  Counter  

atmGenVclStatsOamLoopbackRcvCells 1.3.6.1.4.1.2926.25.7.1.2.3.1.10
The total number of Loopback OAM cells received by this virtual circuit.
OBJECT-TYPE    
  Counter  

atmGenVclStatsOamLoopbackXmtCells 1.3.6.1.4.1.2926.25.7.1.2.3.1.11
The total number of Loopback OAM cells transmitted by this virtual circuit.
OBJECT-TYPE    
  Counter  

atmGenLogicalPortTable 1.3.6.1.4.1.2926.25.7.1.3.1
A table of physical layer status and parameter information for the UNI's physical interface
OBJECT-TYPE    
  SEQUENCE OF  
    AtmGenLogicalPortEntry

atmGenLogicalPortEntry 1.3.6.1.4.1.2926.25.7.1.3.1.1
A entry in the table, containing information about the physical layer of a UNI interface
OBJECT-TYPE    
  AtmGenLogicalPortEntry  

atmGenLpIfIndex 1.3.6.1.4.1.2926.25.7.1.3.1.1.1
The logical port index.
OBJECT-TYPE    
  INTEGER 257..512  

atmGenLpPhysIf 1.3.6.1.4.1.2926.25.7.1.3.1.1.2
The physical interface associated with this logical port.
OBJECT-TYPE    
  INTEGER 1..256  

atmGenLpLoopTime 1.3.6.1.4.1.2926.25.7.1.3.1.1.3
The time (in hundredths of a second) to drop a receive frame.
OBJECT-TYPE    
  INTEGER  

atmGenLpProtocol 1.3.6.1.4.1.2926.25.7.1.3.1.1.4
Network layer for the VC's attached to this LP
OBJECT-TYPE    
  INTEGER ethernet(7), ethernetII(8), ethernet8023(9), tokenRing(10), fddi(11)  

atmGenLpAal5EncapsType 1.3.6.1.4.1.2926.25.7.1.3.1.1.5
An instance of this object only exists when the local VCL end-point is also the VCC end-point, and AAL5 is in use. The type of data encapsulation used over the AAL5 SSCS layer. The definitions reference RFC 1483 Multiprotocol Encapsulation over ATM AAL5 and to the ATM Forum LAN Emulation specification.
OBJECT-TYPE    
  INTEGER rfc1483-vc(1), rfc1483-llc(2)  

atmGenLpAal5Mtu 1.3.6.1.4.1.2926.25.7.1.3.1.1.6
The PDU size for the AAL5 CPCS layer that can be processed by the AAL5 entity, 64 - 16K.
OBJECT-TYPE    
  INTEGER  

atmGenLpAal5RateQ 1.3.6.1.4.1.2926.25.7.1.3.1.1.7
The rate queue used by this virtual circuit.
OBJECT-TYPE    
  INTEGER  

atmGenLpAdminStatus 1.3.6.1.4.1.2926.25.7.1.3.1.1.8
The logical port status, just for reference. The Port Manager has control of the status.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

atmGenLpLoopThreshold 1.3.6.1.4.1.2926.25.7.1.3.1.1.9
The number of frames receives before a snmp trap will be sent.
OBJECT-TYPE    
  INTEGER  

atmGenLpLoopTrapTime 1.3.6.1.4.1.2926.25.7.1.3.1.1.10
The time (in seconds) between checks to send out snmp trap.
OBJECT-TYPE    
  INTEGER  

atmGenLpOamGeneration 1.3.6.1.4.1.2926.25.7.1.3.1.1.11
Enable or Disable the generation of OAM cells.
OBJECT-TYPE    
  INTEGER  

cesConfTable 1.3.6.1.4.1.2926.25.7.1.4.1
The CES configuration table used to manage interworking between CBR interfaces or channels and ATM Virtual Channel Links (VCLs). The reverse mapping is shown in the cesMappingTable.
OBJECT-TYPE    
  SEQUENCE OF  
    CesConfEntry

cesConfEntry 1.3.6.1.4.1.2926.25.7.1.4.1.1
An entry in the CES configuration table. There is one entry in the table per ATM Port/VPI/VCI.
OBJECT-TYPE    
  CesConfEntry  

cesAtmPhysPort 1.3.6.1.4.1.2926.25.7.1.4.1.1.1
The value of this object is equal to MIB II's ifIndex value of the ATM Port interface mapped through this CES IWF to a CBR interface. This value is overwritten whenever an active or passive SVC is established. The distinguished value zero indicates that no ATM interface has been specified.
OBJECT-TYPE    
  INTEGER  

cesAtmVpi 1.3.6.1.4.1.2926.25.7.1.4.1.1.2
The value of this object is equal to the VPI used by the ATM VCL mapped through this CES IWF to a CBR interface. This value is overwritten whenever an active or passive SVC is established. The value is not relevant if no ATM interface has been specified (i.e., cesAtmIndex is set to zero).
OBJECT-TYPE    
  INTEGER 0..255  

cesAtmVci 1.3.6.1.4.1.2926.25.7.1.4.1.1.3
The value of this object is equal to the VCI used by the ATM VCL mapped through this CES IWF to a CBR interface. This value is overwritten whenever an active or passive SVC is established. The distinguished value zero indicates that no ATM VCL has been specified.
OBJECT-TYPE    
  INTEGER 1..1023  

cesCbrService 1.3.6.1.4.1.2926.25.7.1.4.1.1.4
Define if DSx/Ex service is structured or unstructured. A structured(2) interface is some nx64kbKbps. An unstructured (1) interface is 1.544Mbps, 2.048Mbps, 6.312Mbps, 44.736 Mbps, or 34.368 Mbps. unstructured(1) passes all bits through the ATM network. strucutured(2) passes data bits through the ATM network, and may also pass signalling bits At this time, only unstructured mode is defined for the 44.736 Mbps and 34.368 Mbps services.
OBJECT-TYPE    
  INTEGER unstructured(1), structured(2)  

cesCbrClockMode 1.3.6.1.4.1.2926.25.7.1.4.1.1.5
Define if DSx/Ex service clocking mode. This maps into transmit clock source of CBR interface. For structured modes this value, if present, must be set to synchronous(1).
OBJECT-TYPE    
  INTEGER synchronous(1), srts-master(2), adaptive(3), srts-slave(4)  

cesCas 1.3.6.1.4.1.2926.25.7.1.4.1.1.6
This parameter selects which AAL1 Format should be used: Without does not carry CAS bits, and uses a single 125 usec frame. With carris CAS bits in a multiframe structure for E1, DS1 SF, or DS1 ESF. This applies to structured interfaces only. Default is without (1). For unstructured interfaces this value, if present, must be set to the default of without (1).
OBJECT-TYPE    
  INTEGER without(1), with(2)  

cesPartialFill 1.3.6.1.4.1.2926.25.7.1.4.1.1.7
If partial cell fill is used, the number of user octets per cell must be set with this parameter. Setting this parameter to zero disables partial cell fill, and causes all cells to be completely filled before they are sent.
OBJECT-TYPE    
  INTEGER 0..47  

cesBufMaxSize 1.3.6.1.4.1.2926.25.7.1.4.1.1.8
Define maximum size in 10 microsecond increments of the reassembly buffer. Some implementations may want allow the maximum buffer size to be programmed to a size less than the physical limit to reduce the maximum delay through a circuit.
OBJECT-TYPE    
  INTEGER 1..65536  

cesCdvRxT 1.3.6.1.4.1.2926.25.7.1.4.1.1.9
The maximum cell arrival jitter in 10 usec increments that the reassembly process will tolerate in the cell stream without producing errors on the CBR service interface.
OBJECT-TYPE    
  INTEGER 1..65535  

cesCellLossIntegrationPeriod 1.3.6.1.4.1.2926.25.7.1.4.1.1.10
The time in milliseconds for the cell loss integration period. If a cells are continuously lost for this period of time, cesCellLossStatus is set to loss (2). The default definition is 2500.
OBJECT-TYPE    
  INTEGER 1000..65535  

cesConnType 1.3.6.1.4.1.2926.25.7.1.4.1.1.11
The type of ATM connectivity between associated CES IWF's. Valid values are: other - none of the types specified below pvc - supporting connectivity is a permanent virtual connection activeSvc - attempt calls whenever none established passiveSvc - accept calls Only pvc is supported in this release.
OBJECT-TYPE    
  INTEGER pvc(2)  

cesDynBw 1.3.6.1.4.1.2926.25.7.1.4.1.1.12
The Sonoma Dynamic Bandwidth feature may be enabled or disabled.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

cesSigType 1.3.6.1.4.1.2926.25.7.1.4.1.1.13
This is the A/B signalling type for dynamic bandwidth Idle detection.
OBJECT-TYPE    
  INTEGER other(1), fxo-loop(2), fxs-loop(3), fxo-ground(4), fxs-ground(5), e-and-m(6), r2(7)  

cesConfAction 1.3.6.1.4.1.2926.25.7.1.4.1.1.14
The value of this object indicates whether the entry, is to be attached or removed from the CES Configuration Table. A value of attach has the effect of adding an entry to this table. A value of remove has the effect of removing an entry from the table.
OBJECT-TYPE    
  INTEGER attach(5), remove(6)  

cesStatsTable 1.3.6.1.4.1.2926.25.7.1.4.3
The CES AAL1 statistical data table.
OBJECT-TYPE    
  SEQUENCE OF  
    CesStatsEntry

cesStatsEntry 1.3.6.1.4.1.2926.25.7.1.4.3.1
An entry in the CES AAL1 Stats table. There is one entry in this table corresponding to each entry in the cesConfTable.
OBJECT-TYPE    
  CesStatsEntry  

cesStatsAtmPhyPort 1.3.6.1.4.1.2926.25.7.1.4.3.1.1
The physical interface instance.
OBJECT-TYPE    
  INTEGER  

cesStatsAtmVpi 1.3.6.1.4.1.2926.25.7.1.4.3.1.2
The VPI value of the VCL, 0 - 255.
OBJECT-TYPE    
  INTEGER 0..255  

cesStatsAtmVci 1.3.6.1.4.1.2926.25.7.1.4.3.1.3
The VCI value of the VCL, 35 - 1023.
OBJECT-TYPE    
  INTEGER 35..1023  

cesReassCells 1.3.6.1.4.1.2926.25.7.1.4.3.1.4
This count gives the number of cells played out to the CES Service Interface. It excludes cells that were discarded for any reason, including cells that were not used due to being declared misinserted, or discarded while the reassembler was waiting to achieve synchronization.
OBJECT-TYPE    
  Counter  

cesHdrErrors 1.3.6.1.4.1.2926.25.7.1.4.3.1.5
The count of the number of AAL1 header errors detected, including those corrected. Header errors include correctable and uncorrectable CRC, plus bad parity.
OBJECT-TYPE    
  Counter  

cesPointerReframes 1.3.6.1.4.1.2926.25.7.1.4.3.1.6
This records the count of the number of events in which the AAL1 reassembler found that an SDT pointer is not where it is expected, and the pointer must be reacquired. This count is only meaningful for structured CES modes, as unstructured CES modes do not use pointers. For unstructured CES modes, this count, if present, should indicate zero.
OBJECT-TYPE    
  Counter  

cesPointerParityErrors 1.3.6.1.4.1.2926.25.7.1.4.3.1.7
This records the count of the number of events in which the AAL1 reassembler detects a parity check failure at the point where a structured data pointer is expected. This count is only meaningful for structured CES modes, as unstructured CES modes do not use pointers. For unstructured CES modes, this count, if present, should indicate zero.
OBJECT-TYPE    
  Counter  

cesAal1SeqErrors 1.3.6.1.4.1.2926.25.7.1.4.3.1.8
Number of times that the sequence number of an incoming AAL1 Type 1 SAR-PDU causes a transition from the 'sync' state to the 'out of sequence' state, as defined by ITU-T I.363.1.
OBJECT-TYPE    
  Counter  

cesLostCells 1.3.6.1.4.1.2926.25.7.1.4.3.1.9
Number of lost cells, as detected by the AAL1 sequence number processing, for example. This records the count of the number of cells detected as lost in the network prior to the destination CES IWF AAL1 layer processing.
OBJECT-TYPE    
  Counter  

cesMisinsertedCells 1.3.6.1.4.1.2926.25.7.1.4.3.1.10
Number of AAL1 sequence violations which the AAL Convergence sublayer interprets as a misinserted cell, as defined by ITU-T I.363.1.
OBJECT-TYPE    
  Counter  

cesBufUnderflows 1.3.6.1.4.1.2926.25.7.1.4.3.1.11
Number of buffer underflows. This records the count of the number of times the CES reassembly buffer underflows. In the case of a continuous underflow caused by a loss of ATM cell flow, a single buffer underflow should be counted. If the CES IWF is implemented with multiple buffers (such as a cell level buffer and a bit level buffer), then either buffer underflow will cause this count to be incremented.
OBJECT-TYPE    
  Counter  

cesBufOverflows 1.3.6.1.4.1.2926.25.7.1.4.3.1.12
Number of buffer overflows. This records the count of the number of times the CES reassembly buffer overflows. If the CES IWF is implemented with multiple buffers (such as a cell level buffer and a bit level buffer, then either buffer overflow will cause this count to be incremented
OBJECT-TYPE    
  Counter  

cesCellLossStatus 1.3.6.1.4.1.2926.25.7.1.4.3.1.13
When cells are continuously lost for the number of milliseconds specified by cesCellLossIntegrationPeriod, the value is set to loss (2). When cells are no longer lost, the value is set to noLoss (1).
OBJECT-TYPE    
  INTEGER noLoss(1), loss(2)  

cesAttachmentTable 1.3.6.1.4.1.2926.25.7.1.4.4
This table is used to attach a bundle to a physical port and DS0 channel.
OBJECT-TYPE    
  SEQUENCE OF  
    CesAttachmentEntry

cesAttachmentEntry 1.3.6.1.4.1.2926.25.7.1.4.4.1
This is an entry in the attach bundle to physical port and DS0 channel table. An entry in this table indicates if the bundle is attached to the physical port and what DS0 channel on the physical port the bundle is attached to, if applicable. To set an entry in this table, ALL the objects in the entry must be present in a single SET PDU.
OBJECT-TYPE    
  CesAttachmentEntry  

cesAttachmentPhysPort 1.3.6.1.4.1.2926.25.7.1.4.4.1.1
The physical port number of the port to which the bundle is being attached.
OBJECT-TYPE    
  INTEGER 1..256  

cesAttachmentBundle 1.3.6.1.4.1.2926.25.7.1.4.4.1.2
The bundle number. The range of settable values for this object is 1025 to 1536.
OBJECT-TYPE    
  INTEGER 1025..1536  

cesAttachmentChan 1.3.6.1.4.1.2926.25.7.1.4.4.1.3
The value of this object indicates the DS0 channel to which the bundle, identified by cesAttachmentBundle, is attached or is to be attached.
OBJECT-TYPE    
  INTEGER 0..32  

cesAttachmentAction 1.3.6.1.4.1.2926.25.7.1.4.4.1.4
The value of this object indicates whether the bundle, is to be attached or removed from the physical port and DS0 channel. A value of attach has the effect of adding an entry to this table, and either to create the bundle, or to attach it to another physical port. A value of remove has the effect of removing an entry from the table and if the DS0 channel is the last one attached to the bundle then the remove action has the effect of deleting the bundle also.
OBJECT-TYPE    
  INTEGER attach(5), remove(6)  

atmAsiConfGroup 1.3.6.1.4.1.2926.25.7.1.5.1
OBJECT IDENTIFIER    

atmAsiStatsGroup 1.3.6.1.4.1.2926.25.7.1.5.2
OBJECT IDENTIFIER    

atmAsiConfPhyTable 1.3.6.1.4.1.2926.25.7.1.5.1.1
A table of physical layer configuration for the ASI interface
OBJECT-TYPE    
  SEQUENCE OF  
    AtmAsiConfPhyEntry

atmAsiConfPhyEntry 1.3.6.1.4.1.2926.25.7.1.5.1.1.1
A entry in the table, containing information about the physical layer of an ASI interface
OBJECT-TYPE    
  AtmAsiConfPhyEntry  

atmAsiConfPhysIndex 1.3.6.1.4.1.2926.25.7.1.5.1.1.1.1
The physical interface index.
OBJECT-TYPE    
  INTEGER  

atmAsiConfLineType 1.3.6.1.4.1.2926.25.7.1.5.1.1.1.2
Configure the line type.
OBJECT-TYPE    
  INTEGER esf(2), d4(3), e1(4), e1-crc(5), e1-cas(6), e1-crc-cas(7)  

atmAsiConfLineCoding 1.3.6.1.4.1.2926.25.7.1.5.1.1.1.4
Configure the line coding.
OBJECT-TYPE    
  INTEGER b8zs(2), hdb3(3), zbtsi(4), ami(5)  

atmAsiConfTxClkSelect 1.3.6.1.4.1.2926.25.7.1.5.1.1.1.5
This parameter configures the source of the Tx clock.
OBJECT-TYPE    
  INTEGER internal(1), line(2), through(3)  

atmAsiConfSignalMode 1.3.6.1.4.1.2926.25.7.1.5.1.1.1.6
This parameter configures the signal mode.
OBJECT-TYPE    
  INTEGER none(1), robbed-bit(2), bit-oriented(3)  

atmAsiConfLIUType 1.3.6.1.4.1.2926.25.7.1.5.1.1.1.7
This parameter configures the Line Interface Unit type.
OBJECT-TYPE    
  INTEGER t1-long(1), itu-120(2), itu-75(3), dsx1-short(4)  

atmAsiConfLBOType 1.3.6.1.4.1.2926.25.7.1.5.1.1.1.8
This parameter configures the Line Build Out.
OBJECT-TYPE    
  INTEGER short-133(1), short-266(2), short-399(3), short-533(4), short-655(5), long-0(8), long-75(9), long-150(10), long-225(11)  

atmAsiConfIdlePattern 1.3.6.1.4.1.2926.25.7.1.5.1.1.1.9
This parameter configures the idle pattern for trunk conditioning.
OBJECT-TYPE    
  INTEGER 0..255  

atmAsiConfLoopbackMode 1.3.6.1.4.1.2926.25.7.1.5.1.1.1.10
This parameter configures the loopback mode.
OBJECT-TYPE    
  INTEGER disable(1), internal(2), external(3)  

atmAsiConfStopMode 1.3.6.1.4.1.2926.25.7.1.5.1.1.1.11
This parameter configures the mode used for stop commands.
OBJECT-TYPE    
  INTEGER immediate(1), on-idle(2)  

atmAsiConfRecoveredClkSource 1.3.6.1.4.1.2926.25.7.1.5.1.1.1.12
This parameter configures the source of the recovered clock used for through timing.
OBJECT-TYPE    
  INTEGER fourth-port(1), third-port(2), second-port(3), first-port(4), phy-port(5)  

atmAsiDebugAddr 1.3.6.1.4.1.2926.25.7.1.5.1.1.1.13
PCI Phy address for DS1 port register.
OBJECT-TYPE    
  INTEGER  

atmAsiDebugReadValue 1.3.6.1.4.1.2926.25.7.1.5.1.1.1.14
Value read from DS1 port register.
OBJECT-TYPE    
  INTEGER  

atmAsiDebugWriteValue 1.3.6.1.4.1.2926.25.7.1.5.1.1.1.15
Value written to DS1 port register.
OBJECT-TYPE    
  INTEGER  

atmAsiDebugRead 1.3.6.1.4.1.2926.25.7.1.5.1.1.1.16
Read or Write of DS1 port register (TRUE = READ).
OBJECT-TYPE    
  INTEGER read(1), write(2)  

atmAsiStatsTable 1.3.6.1.4.1.2926.25.7.1.5.2.1
A table of physical layer statistics information for the ASI interface
OBJECT-TYPE    
  SEQUENCE OF  
    AtmAsiStatsEntry

atmAsiStatsEntry 1.3.6.1.4.1.2926.25.7.1.5.2.1.1
A entry in the table, containing information about the physical layer of an ASI interface
OBJECT-TYPE    
  AtmAsiStatsEntry  

atmAsiStatsPhysIndex 1.3.6.1.4.1.2926.25.7.1.5.2.1.1.1
The physical interface index.
OBJECT-TYPE    
  INTEGER  

atmAsiStatsNoSignals 1.3.6.1.4.1.2926.25.7.1.5.2.1.1.2
No signal error counter.
OBJECT-TYPE    
  Counter  

atmAsiStatsAISDetects 1.3.6.1.4.1.2926.25.7.1.5.2.1.1.3
AIS Detect counter.
OBJECT-TYPE    
  Counter  

atmAsiStatsYelAlarmCount 1.3.6.1.4.1.2926.25.7.1.5.2.1.1.4
A count of the number of Yellow Alarms.
OBJECT-TYPE    
  Counter  

atmAsiStatsLCVErrors 1.3.6.1.4.1.2926.25.7.1.5.2.1.1.5
LCV (Line Code Violation) error counter.
OBJECT-TYPE    
  Counter  

atmAsiStatsPCVErrors 1.3.6.1.4.1.2926.25.7.1.5.2.1.1.6
PCV (Path Code Violation) error counter.
OBJECT-TYPE    
  Counter  

atmAsiStatsMOSErrors 1.3.6.1.4.1.2926.25.7.1.5.2.1.1.7
Multiframe out of sync error counter.
OBJECT-TYPE    
  Counter  

atmAsiStatsSyncLossCount 1.3.6.1.4.1.2926.25.7.1.5.2.1.1.8
Sync Loss counter.
OBJECT-TYPE    
  Counter  

atmAsiStatsHECErrors 1.3.6.1.4.1.2926.25.7.1.5.2.1.1.9
HEC error counter.
OBJECT-TYPE    
  Counter  

atmAsiStatsSignalLoss 1.3.6.1.4.1.2926.25.7.1.5.2.1.1.10
Signal loss indication.
OBJECT-TYPE    
  INTEGER true(1), false(2)  

atmAsiStatsAISDetect 1.3.6.1.4.1.2926.25.7.1.5.2.1.1.11
AIS indication.
OBJECT-TYPE    
  INTEGER true(1), false(2)  

atmAsiStatsYellowAlarm 1.3.6.1.4.1.2926.25.7.1.5.2.1.1.12
Yellow Alarm indication.
OBJECT-TYPE    
  INTEGER true(1), false(2)  

atmAsiStatsSyncLoss 1.3.6.1.4.1.2926.25.7.1.5.2.1.1.13
Loss of sync indication.
OBJECT-TYPE    
  INTEGER true(1), false(2)  

atmAsiStatsTxClockLoss 1.3.6.1.4.1.2926.25.7.1.5.2.1.1.14
Loss of transmit clock indication.
OBJECT-TYPE    
  INTEGER true(1), false(2)  

atmAsiStatsClearCounters 1.3.6.1.4.1.2926.25.7.1.5.2.1.1.15
Clear all counters in this group ONLY.
OBJECT-TYPE    
  INTEGER true(1), false(2)  

atmAsmPhyConfGroup 1.3.6.1.4.1.2926.25.7.1.6.1
OBJECT IDENTIFIER    

atmAsmPhyConfTable 1.3.6.1.4.1.2926.25.7.1.6.1.1
A table of physical layer configuration for the ASM interfaces.
OBJECT-TYPE    
  SEQUENCE OF  
    AtmAsmPhyConfEntry

atmAsmPhyConfEntry 1.3.6.1.4.1.2926.25.7.1.6.1.1.1
A entry in the table, containing information about the physical layer of an ASM interfaces.
OBJECT-TYPE    
  AtmAsmPhyConfEntry  

atmAsmPhyConfIndex 1.3.6.1.4.1.2926.25.7.1.6.1.1.1.1
The physical interface index.
OBJECT-TYPE    
  INTEGER  

atmAsmPhyConfAdminLineUsage 1.3.6.1.4.1.2926.25.7.1.6.1.1.1.2
The desired physical port's line usage. For some port types, the desired line usage will become effective after the system is rebooted.
OBJECT-TYPE    
  INTEGER ces-udt(1), ces-sdt(2), uni(4), ima(5)  

atmAsmPhyConfOperLineUsage 1.3.6.1.4.1.2926.25.7.1.6.1.1.1.3
The physical port's current line usage.
OBJECT-TYPE    
  INTEGER ces-udt(1), ces-sdt(2), uni(4), ima(5)