MY-NTP-MIB
File:
MY-NTP-MIB.mib (9289 bytes)
Imported modules
Imported symbols
Defined Types
NTPLeapIndicator |
|
INTEGER |
noWarning(0), addSecond(1), subtractSecond(2), alarm(3) |
|
|
Defined Values
myNtpMIB |
1.3.6.1.4.1.4881.1.1.10.2.49 |
This module defines my ntp mibs. |
MODULE-IDENTITY |
|
|
|
myntpSystem |
1.3.6.1.4.1.4881.1.1.10.2.49.1.1 |
OBJECT IDENTIFIER |
|
|
|
myntpSysLeap |
1.3.6.1.4.1.4881.1.1.10.2.49.1.1.1 |
Two-bit code warning of an impending leap second to
be inserted in the NTP timescale. This object can be
set only when the myntpSysStratum has a value of 1. |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
NTPLeapIndicator |
|
|
myntpSysStratum |
1.3.6.1.4.1.4881.1.1.10.2.49.1.1.2 |
The stratum of the local clock. If the value is set
to 1, i.e., this is a primary reference, then the
Primary-Clock procedure described in Section 3.4.6,
in RFC-1305 is invoked. |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
NTPStratum |
|
|
myntpSysPrecision |
1.3.6.1.4.1.4881.1.1.10.2.49.1.1.3 |
Signed integer indicating the precision
of the system clock, in seconds to the nearest
power of two. The value must be rounded to the
next larger power of two; for instance, a 50-Hz
(20 ms) or 60-Hz (16.67 ms) power-frequency clock
would be assigned the value -5 (31.25 ms), while a
1000-Hz (1 ms) crystal-controlled clock would be
assigned the value -9 (1.95 ms). |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
-24..24 |
|
myntpSysRootDelay |
1.3.6.1.4.1.4881.1.1.10.2.49.1.1.4 |
A signed fixed-point number indicating the total
round-trip delay in seconds, to the primary reference
source at the root of the synchronization subnet. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
NTPSignedTimeValue |
|
|
myntpSysRootDispersion |
1.3.6.1.4.1.4881.1.1.10.2.49.1.1.5 |
The maximum error in seconds, relative to the
primary reference source at the root of the
synchronization subnet. Only positive values greater
than zero are possible. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
NTPUnsignedTimeValue |
|
|
myntpSysRefId |
1.3.6.1.4.1.4881.1.1.10.2.49.1.1.6 |
The reference identifier of the local clock. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
NTPRefId |
|
|
myntpSysRefTime |
1.3.6.1.4.1.4881.1.1.10.2.49.1.1.7 |
The local time when the local clock was last
updated. If the local clock has never been
synchronized, the value is zero. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
NTPTimeStamp |
|
|
myNtpSysGroup |
1.3.6.1.4.1.4881.1.1.10.2.49.2.2.1 |
The NTP system variables. |
Status: current |
Access: read-only |
OBJECT-GROUP |
|
|
|
myNtpMIBCompliance |
1.3.6.1.4.1.4881.1.1.10.2.49.2.1.1 |
The compliance statement for agents which implement the NTP MIB. |
Status: current |
Access: read-only |
MODULE-COMPLIANCE |
|
|
|