L2L3-VPN-MULTICAST-MIB
File:
L2L3-VPN-MULTICAST-MIB.mib (10392 bytes)
Imported modules
Imported symbols
Defined Types
L2L3VpnMcastPmsiTunnelAttributeEntry |
|
SEQUENCE |
|
|
|
|
l2L3VpnMcastPmsiTunnelAttributeType |
L2L3VpnMcastProviderTunnelType |
|
|
l2L3VpnMcastPmsiTunnelAttributeId |
L2L3VpnMcastProviderTunnelId |
|
|
l2L3VpnMCastPmsiTunnelLeafInfoRequired |
INTEGER |
|
|
l2L3VpnMcastPmsiTunnelAttributeMplsLabel |
MplsLabel |
|
|
l2L3VpnMcastPmsiTunnelPointer |
RowPointer |
|
|
l2L3VpnMcastPmsiTunnelIf |
RowPointer |
|
Defined Values
l2L3VpnMcastMIB |
1.3.6.1.2.1.245 |
This MIB module defines a table representing the attribute
information of the provider tunnels (P-tunnels) on a PE router.
This MIB module will be used by other MIB modules designed for
monitoring and/or configuring Border Gateway
Protocol/Multiprotocol Label Switching
Layer 2 and Layer 3 Virtual Private
Network that support multicast (L2L3VpnMCast network).
Copyright (c) 2018 IETF Trust and the persons identified
as authors of the code. All rights reserved.
Redistribution and use in source and binary forms, with or
without modification, is permitted pursuant to, and subject
to the license terms contained in, the Simplified BSD License
set forth in Section 4.c of the IETF Trust's Legal Provisions
Relating to IETF Documents
(http://trustee.ietf.org/license-info).
|
MODULE-IDENTITY |
|
|
|
l2L3VpnMcastPmsiTunnelAttributeTable |
1.3.6.1.2.1.245.1.1 |
An entry in this table corresponds to
the attribute information of a specific
P-tunnel on a PE router.
A part of the attributes corresponds to fields in
a Provider Multicast Service Interface (PMSI) Tunnel
attribute advertised and received by a PE router.
The entries will be referred to by other MIB modules
for monitoring and/or configuring L2L3VpnMCast networks.
|
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
L2L3VpnMcastPmsiTunnelAttributeEntry |
|
l2L3VpnMcastPmsiTunnelAttributeEntry |
1.3.6.1.2.1.245.1.1.1 |
A conceptual row corresponding to a specific
P-tunnel on this router.
|
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
L2L3VpnMcastPmsiTunnelAttributeEntry |
|
|
l2L3VpnMcastPmsiTunnelAttributeType |
1.3.6.1.2.1.245.1.1.1.1 |
This object indicates the type of tunneling technology
used to establish the P-tunnel corresponding to this entry.
When BGP-based PMSI signaling is used, the value of
this object corresponds to the Tunnel Type field
in the PMSI Tunnel attribute advertised/received
in a PMSI auto-discovery (A-D) route.
|
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
L2L3VpnMcastProviderTunnelType |
|
|
l2L3VpnMcastPmsiTunnelAttributeId |
1.3.6.1.2.1.245.1.1.1.2 |
This object represents the Tunnel Identifier field, which
uniquely identifies a P-tunnel, in the PMSI Tunnel attribute
of the P-tunnel corresponding to this entry.
The size of the identifier depends on the address family
(IPv4 or IPv6) and the value of the corresponding
l2L3VpnMcastPmsiTunnelAttributeType object, i.e., the type of
tunneling technology used to establish the P-tunnel.
|
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
L2L3VpnMcastProviderTunnelId |
|
|
l2L3VpnMCastPmsiTunnelLeafInfoRequired |
1.3.6.1.2.1.245.1.1.1.3 |
When the value of this object is set to 1 (true),
it indicates that the PE that originated the
PMSI Tunnel attribute of the P-tunnel corresponding
to this entry requests receivers to originate
a new Leaf A-D route.
A value of zero (false) indicates that there is no such
request.
When the P-tunnel does not have a corresponding PMSI
Tunnel attribute, the value of this object will be
2 (notAvailable).
In the case of multicast in MPLS/BGP IP VPNs,
this object represents the 'Leaf Information Required flag'
(RFC 6514) in the Flags field in the PMSI Tunnel attribute
of the P-tunnel corresponding to this entry.
|
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
false(0), true(1), notAvailable(2) |
|
l2L3VpnMcastPmsiTunnelAttributeMplsLabel |
1.3.6.1.2.1.245.1.1.1.4 |
This object represents the MPLS Label in the PMSI Tunnel
attribute of the P-tunnel corresponding to this entry.
When BGP-based PMSI signaling is used, the PMSI Tunnel
attribute of the P-tunnel will be advertised/received
in a PMSI A-D route. The value of
this object corresponds to the MPLS Label in the attribute.
When the P-tunnel does not have a PMSI tunnel
attribute, the value of this object will be zero.
|
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
MplsLabel |
|
|
l2L3VpnMcastPmsiTunnelPointer |
1.3.6.1.2.1.245.1.1.1.5 |
Details of a P-tunnel identified by
l2L3VpnMcastPmsiTunnelAttributeId may be present
in some other table, e.g.,
mplsTunnelTable (RFC 3812). This object specifies
the pointer to the row that pertains to the entry
in the table.
If no such entry exists, the value of this object
will be zeroDotZero.
|
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
RowPointer |
|
|
l2L3VpnMcastPmsiTunnelIf |
1.3.6.1.2.1.245.1.1.1.6 |
If the P-tunnel identified by
l2L3VpnMcastPmsiTunnelAttributeId has a corresponding
entry in ifXTable (RFC 2863), this object will
point to the row in ifXTable that pertains to the entry.
Otherwise, the value of this object will be zeroDotZero.
|
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
RowPointer |
|
|
l2L3VpnMcastCoreCompliance |
1.3.6.1.2.1.245.2.1.1 |
The core compliance statement for SNMP entities
that implement the L2L3-VPN-MULTICAST-MIB module.
|
Status: current |
Access: read-only |
MODULE-COMPLIANCE |
|
|
|
l2L3VpnMcastFullCompliance |
1.3.6.1.2.1.245.2.1.2 |
The full compliance statement for SNMP entities
that implement the L2L3-VPN-MULTICAST-MIB module.
|
Status: current |
Access: read-only |
MODULE-COMPLIANCE |
|
|
|
l2L3VpnMcastCoreGroup |
1.3.6.1.2.1.245.2.2.1 |
Support of these objects is required.
|
Status: current |
Access: read-only |
OBJECT-GROUP |
|
|
|
l2L3VpnMcastOptionalGroup |
1.3.6.1.2.1.245.2.2.2 |
Support of these objects is optional.
|
Status: current |
Access: read-only |
OBJECT-GROUP |
|
|
|