Juniper-MPLS-MIB

File: Juniper-MPLS-MIB.mib (112815 bytes)

Imported modules

SNMPv2-SMI	SNMPv2-TC	SNMPv2-CONF
IF-MIB	Juniper-MIBs	Juniper-TC

Imported symbols

MODULE-IDENTITY	OBJECT-TYPE	Integer32
IpAddress	Unsigned32	RowStatus
DisplayString	TruthValue	TEXTUAL-CONVENTION
MODULE-COMPLIANCE	OBJECT-GROUP	InterfaceIndex
InterfaceIndexOrZero	juniMibs	JuniNextIfIndex

Defined Types

JuniMajorCfgVciRanges
Generic VCI label range specifier for both resource reservation protocol (RSVP) and label distribution protocol (LDP).
TEXTUAL-CONVENTION
	Integer32	33..65535

JuniMajorCfgVpiRanges
Generic VPI label range specifier for both resource reservation protocol (RSVP) and label distribution protocol (LDP).
TEXTUAL-CONVENTION
	Integer32	0..255

JuniMinorCfgBWRanges
Specifies bandwidth requirements for each MPLS tunnel.
TEXTUAL-CONVENTION
	Unsigned32

JuniMinorCfgHoldingAndSetupPriorityRanges
Each LSP has a setup and hold priority before setting it up or preempting it relative to the other LSPs. This convention specifies those ranges.
TEXTUAL-CONVENTION
	Integer32	0..7

JuniMinorCfgRetryTimesAndNorouteRanges
RSVP/LDP will have a number of retries for successfully setting up a tunnel. This value specifies retry value ranges for LDP/RSVP with or without no-route notification.
TEXTUAL-CONVENTION
	Integer32	0..65535

JuniMinorCfgRetryIntervalAndNorouteRanges
RSVP/LDP will have time interval between two successive retries for setting up tunnel successfully. This value specifies the interval ranges for LDP/RSVP with or without no-route notification.
TEXTUAL-CONVENTION
	Integer32	0..60

JuniProfileCfgBWRanges
Bandwidth range specified for each tunnel in tunnel profiling.
TEXTUAL-CONVENTION
	Unsigned32

JuniProfileCfgHoldingAndSetupPriorityRanges
Tunnel setup and hold priority range specified for each tunnel in tunnel profile configuration.
TEXTUAL-CONVENTION
	Integer32	0..7

JuniProfileCfgRetryTimesAndNorouteRanges
Range specified for number of retries for tunnel with or without no-route notification for RSVP/LDP.
TEXTUAL-CONVENTION
	Integer32	0..65535

JuniProfileCfgRetryIntervalAndNorouteRanges
Range specified for retry interval for tunnel with or without no-route notification for RSVP/LDP.
TEXTUAL-CONVENTION
	Integer32	0..60

JuniMplsGroupTargetedHelloSendEntry
SEQUENCE
	juniMplsGroupTargetedHelloSendAddress	IpAddress
	juniMplsGroupLdpTargetedHelloSendMode	INTEGER

JuniMplsGroupTargetedHelloReceiveEntry
SEQUENCE
	juniMplsGroupTargetedHelloReceiveAddress	IpAddress
	juniMplsGroupLdpTargetedHelloReceiveMode	INTEGER

JuniMplsGroupLdpLabelAdverRouteListEntry
SEQUENCE
	juniMplsGroupLdpLabelAdverRouteListName	DisplayString
	juniMplsGroupLdpLabelAdverNbrListName	DisplayString
	juniMplsGroupLabelAdverListMode	INTEGER

JuniMplsGroupLdpProfileEntry
SEQUENCE
	juniMplsGroupLdpProfileName	DisplayString
	juniMplsGroupLdpProfileHelloHoldTime	Integer32
	juniMplsGroupLdpProfileCrLdpAdminState	INTEGER
	juniMplsGroupLdpProfileRowStatus	RowStatus

JuniMplsGroupRsvpProfileEntry
SEQUENCE
	juniMplsGroupRsvpProfileName	DisplayString
	juniMplsGroupRsvpProfileRefreshPeriod	Unsigned32
	juniMplsGroupRsvpProfileCleanupTimeoutFactor	Integer32
	juniMplsGroupRsvpProfileRowStatus	RowStatus

JuniMplsIfMajorEntry
SEQUENCE
	juniMplsIfMajorIndex	InterfaceIndex
	juniMplsIfMajorRowStatus	RowStatus
	juniMplsIfMajorLowerIfIndex	InterfaceIndexOrZero
	juniMplsIfMajorAdminStatus	INTEGER
	juniMplsIfMajorLdpAdminStatus	INTEGER
	juniMplsIfMajorLdpProfileName	DisplayString
	juniMplsIfMajorLdpVpiStart	JuniMajorCfgVpiRanges
	juniMplsIfMajorLdpVpiStop	JuniMajorCfgVpiRanges
	juniMplsIfMajorLdpVciStart	JuniMajorCfgVciRanges
	juniMplsIfMajorLdpVciStop	JuniMajorCfgVciRanges
	juniMplsIfMajorRsvpAdminStatus	INTEGER
	juniMplsIfMajorRsvpProfileName	DisplayString
	juniMplsIfMajorRsvpVpiStart	JuniMajorCfgVpiRanges
	juniMplsIfMajorRsvpVpiStop	JuniMajorCfgVpiRanges
	juniMplsIfMajorRsvpVciStart	JuniMajorCfgVciRanges
	juniMplsIfMajorRsvpVciStop	JuniMajorCfgVciRanges
	juniMplsIfMajorLabelSpaceType	INTEGER
	juniMplsIfMajorOpState	INTEGER
	juniMplsIfMajorCrLdpAdminState	INTEGER

JuniMplsIfMinorEntry
SEQUENCE
	juniMplsIfMinorIndex	InterfaceIndex
	juniMplsIfMinorRowStatus	RowStatus
	juniMplsIfMinorLowerIfIndex	InterfaceIndexOrZero
	juniMplsIfMinorAdminStatus	INTEGER
	juniMplsIfMinorEndpointAddress	IpAddress
	juniMplsIfMinorEndpointDstMask	IpAddress
	juniMplsIfMinorTunnelMetricMode	INTEGER
	juniMplsIfMinorAbsoluteTunnelMetric	Unsigned32
	juniMplsIfMinorRelativeTunnelMetric	Integer32
	juniMplsIfMinorLabelDistProto	INTEGER
	juniMplsIfMinorAnnounceToOspf	TruthValue
	juniMplsIfMinorAnnounceToIsis	TruthValue
	juniMplsIfMinorAnnounceToBgp	TruthValue
	juniMplsIfMinorBandwidth	JuniMinorCfgBWRanges
	juniMplsIfMinorAffinity	OCTET STRING
	juniMplsIfMinorAffinityMask	OCTET STRING
	juniMplsIfMinorSetupPriority	JuniMinorCfgHoldingAndSetupPriorityRanges
	juniMplsIfMinorHoldingPriority	JuniMinorCfgHoldingAndSetupPriorityRanges
	juniMplsIfMinorTunnelName	DisplayString
	juniMplsIfMinorTunnelRetryTimes	JuniMinorCfgRetryTimesAndNorouteRanges
	juniMplsIfMinorTunnelRetryInterval	JuniMinorCfgRetryIntervalAndNorouteRanges
	juniMplsIfMinorTunnelRetryTimesNoroute	JuniMinorCfgRetryTimesAndNorouteRanges
	juniMplsIfMinorTunnelRetryIntervalNoroute	JuniMinorCfgRetryIntervalAndNorouteRanges
	juniMplsIfMinorBaseTunnelName	DisplayString
	juniMplsIfMinorVpnOuiNumber	Integer32
	juniMplsIfMinorVpnIndex	IpAddress
	juniMplsIfMinorTunnelOpState	INTEGER
	juniMplsIfMinorTargetedDynamicTunnel	TruthValue
	juniMplsIfMinorReoptimization	TruthValue

JuniMplsIfMinorPathOptionEntry
SEQUENCE
	juniMplsIfMinorPathOptionIndex	InterfaceIndex
	juniMplsIfMinorPathOptionNumber	Integer32
	juniMplsIfMinorPathOptionProtocol	INTEGER
	juniMplsIfMinorPathOptionLockdown	TruthValue
	juniMplsIfMinorPathOptionPathName	DisplayString
	juniMplsIfMinorPathOptionPathId	Integer32
	juniMplsIfMinorPathOptionRowStatus	RowStatus

JuniMplsTunnelProfileEntry
SEQUENCE
	juniMplsTunnelProfileName	DisplayString
	juniMplsTunnelProfileAdminStatus	INTEGER
	juniMplsTunnelProfileBaseTunnelName	DisplayString
	juniMplsTunnelProfileIpProfileName	DisplayString
	juniMplsTunnelProfileLabelDistProto	INTEGER
	juniMplsTunnelProfileAnnounceToOspf	TruthValue
	juniMplsTunnelProfileAnnounceToIsis	TruthValue
	juniMplsTunnelProfileAnnounceToBgp	TruthValue
	juniMplsTunnelProfileMetricMode	INTEGER
	juniMplsTunnelProfileAbsoluteMetric	Unsigned32
	juniMplsTunnelProfileRelativeMetric	Integer32
	juniMplsTunnelProfileBandwidth	JuniProfileCfgBWRanges
	juniMplsTunnelProfileAffinity	OCTET STRING
	juniMplsTunnelProfileAffinityMask	OCTET STRING
	juniMplsTunnelProfileSetupPriority	JuniProfileCfgHoldingAndSetupPriorityRanges
	juniMplsTunnelProfileHoldingPriority	JuniProfileCfgHoldingAndSetupPriorityRanges
	juniMplsTunnelProfileRetryTimes	JuniProfileCfgRetryTimesAndNorouteRanges
	juniMplsTunnelProfileRetryInterval	JuniProfileCfgRetryIntervalAndNorouteRanges
	juniMplsTunnelProfileRetryTimesNoroute	JuniProfileCfgRetryTimesAndNorouteRanges
	juniMplsTunnelProfileRetryIntervalNoroute	JuniProfileCfgRetryIntervalAndNorouteRanges
	juniMplsTunnelProfileVpnOuiNumber	Integer32
	juniMplsTunnelProfileVpnIndex	IpAddress
	juniMplsTunnelProfileRowStatus	RowStatus
	juniMplsTunnelProfileTargetedDynamicTunnel	TruthValue

JuniMplsTunnelProfilePathOptionEntry
SEQUENCE
	juniMplsTunnelProfileNamePathOption	DisplayString
	juniMplsTunnelProfilePathOptionNumber	Integer32
	juniMplsTunnelProfilePathOptionProtocol	INTEGER
	juniMplsTunnelProfilePathOptionLockdown	TruthValue
	juniMplsTunnelProfilePathOptionPathName	DisplayString
	juniMplsTunnelProfilePathOptionPathId	Integer32
	juniMplsTunnelProfilePathOptionRowStatus	RowStatus

JuniMplsTunnelProfileDynamicEndpointEntry
SEQUENCE
	juniMplsTunnelProfileNameDynamicEndpoint	DisplayString
	juniMplsTunnelProfileDynamicEndpointType	INTEGER
	juniMplsTunnelProfileDynamicEndpointPolicyListType	INTEGER
	juniMplsTunnelProfileDynamicEndpointListName	DisplayString
	juniMplsTunnelProfileDynamicEndpointRowStatus	RowStatus

JuniMplsTunnelProfileTunnelEndpointEntry
SEQUENCE
	juniMplsTunnelProfileNameTunnelEndpoint	DisplayString
	juniMplsTunnelProfileTunnelEndpointAddress	IpAddress
	juniMplsTunnelProfileTunnelEndpointDstMask	IpAddress
	juniMplsTunnelProfileTunnelEndpointRowStatus	RowStatus

JuniMplsExplicitPathEntry
SEQUENCE
	juniMplsExplicitPathName	DisplayString
	juniMplsExplicitPathAdminState	INTEGER
	juniMplsExplicitPathRowStatus	RowStatus

JuniMplsExplicitPathNodeEntry
SEQUENCE
	juniMplsExplicitPathNodeName	DisplayString
	juniMplsExplicitPathNodeIndexNumber	Integer32
	juniMplsExplicitPathNodeLoose	TruthValue
	juniMplsExplicitPathNodeHopAddress	IpAddress
	juniMplsExplicitPathNodeHopAddressMask	IpAddress
	juniMplsExplicitPathNodeRowStatus	RowStatus

Defined Values

juniMplsMIB		1.3.6.1.4.1.4874.2.2.54
The MultiProtocol Label Switching (MPLS) MIB for the Juniper Networks enterprise. This MIB contains managed objects for basic MPLS configuration of: 1. Global tasks - common MPLS usage configurations on a given label switching router (LSR). 2. Interface tasks - MPLS interface (major interface) configurations. 3. Tunnel tasks - tunnel interface (minor interface) configurations. 4. Tunnel profile tasks - configured to be used by multiple MPLS tunnels. 5. Explicit paths - supports dynamic and manual configurations of explicit paths. 6. VPNs - supports constraint-based routing label distribution protocol (CR-LDP) and BGP/MPLS virtual private network (VPN) configurations.
MODULE-IDENTITY

juniMplsObjects		1.3.6.1.4.1.4874.2.2.54.1
OBJECT IDENTIFIER

juniMplsLsrGlobalConfig		1.3.6.1.4.1.4874.2.2.54.1.1
OBJECT IDENTIFIER

juniMplsMajorLayer		1.3.6.1.4.1.4874.2.2.54.1.2
OBJECT IDENTIFIER

juniMplsMinorLayer		1.3.6.1.4.1.4874.2.2.54.1.3
OBJECT IDENTIFIER

juniMplsTunnelProfile		1.3.6.1.4.1.4874.2.2.54.1.4
OBJECT IDENTIFIER

juniMplsExplicitPath		1.3.6.1.4.1.4874.2.2.54.1.5
OBJECT IDENTIFIER

juniMplsGroup		1.3.6.1.4.1.4874.2.2.54.1.1.1
OBJECT IDENTIFIER

juniMplsGroupList		1.3.6.1.4.1.4874.2.2.54.1.1.2
OBJECT IDENTIFIER

juniMplsIfMajorLayer		1.3.6.1.4.1.4874.2.2.54.1.2.1
OBJECT IDENTIFIER

juniMplsIfMinorLayer		1.3.6.1.4.1.4874.2.2.54.1.3.1
OBJECT IDENTIFIER

juniMplsMinorLayerList		1.3.6.1.4.1.4874.2.2.54.1.3.2
OBJECT IDENTIFIER

juniMplsTunnelProfileGroup		1.3.6.1.4.1.4874.2.2.54.1.4.1
OBJECT IDENTIFIER

juniMplsTunnelProfileList		1.3.6.1.4.1.4874.2.2.54.1.4.2
OBJECT IDENTIFIER

juniMplsExplicitPathGroup		1.3.6.1.4.1.4874.2.2.54.1.5.1
OBJECT IDENTIFIER

juniMplsGroupMplsEnable		1.3.6.1.4.1.4874.2.2.54.1.1.1.1
Enables or disables MPLS on the virtual router. When MPLS is created on the virtual router (VR), it remains adminstratively disabled untill it is enabled explicitly. Without administratively enabling the MPLS on VR, it won't function as an LSR even though it holds the MPLS configurations until the MPLS context is destroyed for the VR.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

juniMplsGroupReopTimer		1.3.6.1.4.1.4874.2.2.54.1.1.1.2
All LSPs setup in MPLS domain are reoptimized for better LSPs as and when available. This object allows configuration of the frequency of reoptimization in time interval.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..604800

juniMplsGroupLabelRangeLow		1.3.6.1.4.1.4874.2.2.54.1.1.1.3
The lower end of the range of the platform label space from which the interfaces on a given LSR derive their label space. Ethernet interfaces can use only platform label space while ATM interfaces can use either platform or interface label space. For the successful configuration of the label range both lower and higher end values must be set cuncurrently.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	16..1048576

juniMplsGroupLabelRangeHigh		1.3.6.1.4.1.4874.2.2.54.1.1.1.4
The higher end of the range of the platform label space from which the interfaces on a given LSR derive their label space. Ethernet interfaces can use only platform label space while ATM interfaces can use either platform or interface label space. For the successful configuration of the label range both lower and higher end values must be set cuncurrently.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	16..1048576

juniMplsGroupLspRetryTimesNoroute		1.3.6.1.4.1.4874.2.2.54.1.1.1.5
This object configures the number of retries for LSP setup after a failure due to no available route.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..65535

juniMplsGroupLspRetryIntervalNoroute		1.3.6.1.4.1.4874.2.2.54.1.1.1.6
This object configures the time interval between two successive LSP setup retries after a failure due to no available route.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..60

juniMplsGroupLspRetryTimes		1.3.6.1.4.1.4874.2.2.54.1.1.1.7
Use this object to configure number of retries for LSP setup after a failure other than one due to no available route.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..65535

juniMplsGroupLspRetryInterval		1.3.6.1.4.1.4874.2.2.54.1.1.1.8
Use this object to configure the time interval between two LSP setup retries after a failure other than one due to no available route.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..60

juniMplsGroupLdpRetryTimesNoroute		1.3.6.1.4.1.4874.2.2.54.1.1.1.9
Use this object to configure the number of retries for LDP to setup LSP after a failure due to no available route.
Status: obsolete	Access: read-write
OBJECT-TYPE
	Integer32	0..65535

juniMplsGroupLdpRetryIntervalNoroute		1.3.6.1.4.1.4874.2.2.54.1.1.1.10
Use this object to configure the time interval between two successive LSP setup retries by LDP after a failure due to no available route.
Status: obsolete	Access: read-write
OBJECT-TYPE
	Integer32	0..60

juniMplsGroupLdpRetryTimes		1.3.6.1.4.1.4874.2.2.54.1.1.1.11
Use this object to configure LSP setup retries by LDP after a failure other than one due to no available route.
Status: obsolete	Access: read-write
OBJECT-TYPE
	Integer32	0..65535

juniMplsGroupLdpRetryInterval		1.3.6.1.4.1.4874.2.2.54.1.1.1.12
Use this object to configure time interval between two LSP setup retries by LDP after a failure other than one due to no available route.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..60

juniMplsGroupLdpSessionRetries		1.3.6.1.4.1.4874.2.2.54.1.1.1.13
Use this object to configure the number of LDP session retries.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..65535

juniMplsGroupLdpSessionRetryTimer		1.3.6.1.4.1.4874.2.2.54.1.1.1.14
Use this object to configure the time interval between two LDP session retries.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..60

juniMplsGroupTopologyDrivenIpProfileName		1.3.6.1.4.1.4874.2.2.54.1.1.1.15
Usually IP interfaces are stacked on top of the MPLS tunnels. The profiled tunnels are associated with IP interfaces with profile of IP interfaces. This object configures the name for the IP profile.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

juniMplsGroupTopologyDrivenLdpEgressIpIntf		1.3.6.1.4.1.4874.2.2.54.1.1.1.16
This object allows enabling/disabling of IP interfaces created over egress LSPs setup by topology driven LSP setup configurations.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

juniMplsGroupTopologyDrivenLdpIngressIpIntf		1.3.6.1.4.1.4874.2.2.54.1.1.1.17
This object allows enabling/disabling of IP interfaces created over ingress LSPs setup by topology driven LSP setup configurations.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

juniMplsGroupTopologyDrivenLdpEgressIpIntfHostOnly		1.3.6.1.4.1.4874.2.2.54.1.1.1.18
This object allows enabling/disabling of IP interfaces created over egress LSPs to host only IP addresses setup by topology driven LSP setup configurations.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

juniMplsGroupTopologyDrivenLdpIngressIpIntfHostOnly		1.3.6.1.4.1.4874.2.2.54.1.1.1.19
This object allows enabling/disabling of IP interfaces created over ingress LSPs to host only IP addresses setup by topology driven LSP setup configurations.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

juniMplsGroupTopologyDrivenLdpEgressIpIntfPolicyListType		1.3.6.1.4.1.4874.2.2.54.1.1.1.20
There are two types of policy list type defined for the locally defined labels advertisement to neighbors; viz. accessList and prefixList. This object allows configuration of the egress side of LSR for topology driven LSPs. Set the list type and list name cuncurrently.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	accessList(1), prefixList(2), noPolicyList(3)

juniMplsGroupTopologyDrivenLdpIngressIpIntfPolicyListType		1.3.6.1.4.1.4874.2.2.54.1.1.1.21
There are two types of policy list type defined for the locally defined labels advertisement to neighbors; viz. accessList and prefixList. This object allows configuration of the ingress side of LSR for topology driven LSPs. Set the list type and list name cuncurrently.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	accessList(1), prefixList(2), noPolicyList(3)

juniMplsGroupTopologyDrivenLdpEgressIpIntfPolicyList		1.3.6.1.4.1.4874.2.2.54.1.1.1.22
This object used to configure egress list name of topology driven LSPs over IP interfaces. For successful configurations the egress list name must be set cunncurently with egress list type. Set the list type and list name cuncurrently.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

juniMplsGroupTopologyDrivenLdpIngressIpIntfPolicyList		1.3.6.1.4.1.4874.2.2.54.1.1.1.23
This object used to configure ingress list name of topology driven LSPs over IP interfaces. For successful configurations ingress listname set cunncurently with ingress list type. Set the list type and list name cuncurrently.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

juniMplsGroupTopologyDrivenLdp		1.3.6.1.4.1.4874.2.2.54.1.1.1.24
LDP is used for label distributions control for setting up the LSPs. Topology driven LSPs also setup using LDP label distribution control. This object allows to enable/disable LDP admin state used for topology driven LSPs setup.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

juniMplsGroupLspLabelDistCtrlMode		1.3.6.1.4.1.4874.2.2.54.1.1.1.25
Some FECs correspond to address prefixes which are distributed via a dynamic routing algorithm. The setup of the LSPs for these FECs can be done in one of two ways: Independent LSP Control or Ordered LSP Control. This object displays the LSP lable distribution control mode.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ordered(0), independent(1), undefined(2)

juniMplsGroupLdpAdvHostOnly		1.3.6.1.4.1.4874.2.2.54.1.1.1.26
This object allows to enable/disable LDP label advertisement mode for host only LSPs.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

juniMplsGroupLsrState		1.3.6.1.4.1.4874.2.2.54.1.1.1.27
This object value displays the status of MPLS enabled LSR such as state is up or down etc.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

juniMplsGroupReopNow		1.3.6.1.4.1.4874.2.2.54.1.1.1.28
All LSPs setup in MPLS domain are reoptimized for better LSPs as and when available. Setting this object forces an immediate check for better paths for the existing LSPs.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

juniMplsGroupIpTtlPropagate		1.3.6.1.4.1.4874.2.2.54.1.1.1.29
Indicate the IP TTL propagation status on ingress LSPs. none - Not set to anything. hideForwardedAndLocal - Hide LSP topology from local and forwarded traffic. hideForwarded - Hide LSP topology from forwarded traffic only. hideLocal - Hide LSP topology from local traffic only.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(0), hideForwardedAndLocal(1), hideForwarded(2), hideLocal(3)

juniMplsGroupTargetedHelloSendTable		1.3.6.1.4.1.4874.2.2.54.1.1.2.1
This table contains list of send side IP addresses for LDP targeted hello messages.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		JuniMplsGroupTargetedHelloSendEntry

juniMplsGroupTargetedHelloSendEntry		1.3.6.1.4.1.4874.2.2.54.1.1.2.1.1
Each entry represents send IP address for targeted hello message.
Status: current	Access: not-accessible
OBJECT-TYPE
	JuniMplsGroupTargetedHelloSendEntry

juniMplsGroupTargetedHelloSendAddress		1.3.6.1.4.1.4874.2.2.54.1.1.2.1.1.1
Configure the send side address for targeted hello messages.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

juniMplsGroupLdpTargetedHelloSendMode		1.3.6.1.4.1.4874.2.2.54.1.1.2.1.1.2
Select mode to add/delete to the list of IP addresses for targeted hello messages.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	add(0), delete(1), none(2)

juniMplsGroupTargetedHelloReceiveTable		1.3.6.1.4.1.4874.2.2.54.1.1.2.2
This table contains list of receive side IP addresses for LDP targeted hello messages.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		JuniMplsGroupTargetedHelloReceiveEntry

juniMplsGroupTargetedHelloReceiveEntry		1.3.6.1.4.1.4874.2.2.54.1.1.2.2.1
Each entry represents receive IP address for targeted hello message.
Status: current	Access: not-accessible
OBJECT-TYPE
	JuniMplsGroupTargetedHelloReceiveEntry

juniMplsGroupTargetedHelloReceiveAddress		1.3.6.1.4.1.4874.2.2.54.1.1.2.2.1.1
Configure the receive side address for targeted hello messages.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

juniMplsGroupLdpTargetedHelloReceiveMode		1.3.6.1.4.1.4874.2.2.54.1.1.2.2.1.2
Select mode to add/delete to the list of IP addresses for targeted hello messages.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	add(0), delete(1), none(2)

juniMplsGroupLdpLabelAdverRouteListTable		1.3.6.1.4.1.4874.2.2.54.1.1.2.3
Table is a list of LDP label advertisement entries.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		JuniMplsGroupLdpLabelAdverRouteListEntry

juniMplsGroupLdpLabelAdverRouteListEntry		1.3.6.1.4.1.4874.2.2.54.1.1.2.3.1
Each entry represents access list pairs for the LDP peers label advertisement.
Status: current	Access: not-accessible
OBJECT-TYPE
	JuniMplsGroupLdpLabelAdverRouteListEntry

juniMplsGroupLdpLabelAdverRouteListName		1.3.6.1.4.1.4874.2.2.54.1.1.2.3.1.1
This LDP label advertisement route list name for which this entry contains information.
Status: current	Access: not-accessible
OBJECT-TYPE
	DisplayString	Size(0..32)

juniMplsGroupLdpLabelAdverNbrListName		1.3.6.1.4.1.4874.2.2.54.1.1.2.3.1.2
The LDP label advertisement neighbor route list name for which this entry contains information.
Status: current	Access: not-accessible
OBJECT-TYPE
	DisplayString	Size(0..32)

juniMplsGroupLabelAdverListMode		1.3.6.1.4.1.4874.2.2.54.1.1.2.3.1.3
This object selects the mode of addition/deletion to the list.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	add(0), delete(1), none(2)

juniMplsGroupLdpProfileTable		1.3.6.1.4.1.4874.2.2.54.1.1.2.4
Table is a list of LDP Profile entries.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		JuniMplsGroupLdpProfileEntry

juniMplsGroupLdpProfileEntry		1.3.6.1.4.1.4874.2.2.54.1.1.2.4.1
Each entry represents one LDP profile settings.
Status: current	Access: not-accessible
OBJECT-TYPE
	JuniMplsGroupLdpProfileEntry

juniMplsGroupLdpProfileName		1.3.6.1.4.1.4874.2.2.54.1.1.2.4.1.1
LDP profile name identifies unique entry in the table.
Status: current	Access: not-accessible
OBJECT-TYPE
	DisplayString	Size(0..20)

juniMplsGroupLdpProfileHelloHoldTime		1.3.6.1.4.1.4874.2.2.54.1.1.2.4.1.2
Configure the LDP peers hello hold time period.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..120

juniMplsGroupLdpProfileCrLdpAdminState		1.3.6.1.4.1.4874.2.2.54.1.1.2.4.1.3
Enable or disable the constraint-based routing label distribution protocol (CR-LDP) admin state.
Status: obsolete	Access: read-create
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

juniMplsGroupLdpProfileRowStatus		1.3.6.1.4.1.4874.2.2.54.1.1.2.4.1.4
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: juniMplsGroupLdpProfileCrLdpAdminState juniMplsGroupLdpProfileRowStatus
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

juniMplsGroupRsvpProfileTable		1.3.6.1.4.1.4874.2.2.54.1.1.2.5
Table is a list of LDP Profile entries.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		JuniMplsGroupRsvpProfileEntry

juniMplsGroupRsvpProfileEntry		1.3.6.1.4.1.4874.2.2.54.1.1.2.5.1
Each entry represents one LDP profile settings.
Status: current	Access: not-accessible
OBJECT-TYPE
	JuniMplsGroupRsvpProfileEntry

juniMplsGroupRsvpProfileName		1.3.6.1.4.1.4874.2.2.54.1.1.2.5.1.1
The RSVP profile name identifies unique entry in the table.
Status: current	Access: not-accessible
OBJECT-TYPE
	DisplayString	Size(0..20)

juniMplsGroupRsvpProfileRefreshPeriod		1.3.6.1.4.1.4874.2.2.54.1.1.2.5.1.2
Configure the time out period between the generation of two refresh messages.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	1..1000000000

juniMplsGroupRsvpProfileCleanupTimeoutFactor		1.3.6.1.4.1.4874.2.2.54.1.1.2.5.1.3
Confgure the number of refresh messages can be lost before PATH or RESV state is ended.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..10

juniMplsGroupRsvpProfileRowStatus		1.3.6.1.4.1.4874.2.2.54.1.1.2.5.1.4
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry object MUST be explicitly configured: juniMplsGroupRsvpProfileRowStatus
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

juniMplsIfMajorNextIfIndex		1.3.6.1.4.1.4874.2.2.54.1.2.1.1
Coordinate ifIndex value allocation for entries in the juniMplsIfMajorTable. A GET of this object returns the next available ifIndex value to be used to create an entry in the associated interface table; or zero, if no valid ifIndex value is available. This object also returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that ifIndex allocation is unintended. Successive GETs will typically return different values, thus avoiding collisions among cooperating management clients seeking to create table entries simultaneously.
Status: current	Access: read-only
OBJECT-TYPE
	JuniNextIfIndex

juniMplsIfMajorTable		1.3.6.1.4.1.4874.2.2.54.1.2.1.2
This table contains entries for MPLS Major interfaces present in the system.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		JuniMplsIfMajorEntry

juniMplsIfMajorEntry		1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1
Each entry describes the characteristics of an MPLS Major interface. Creating/deleting entries in this table causes corresponding entries to be created/deleted in ifTable/ifXTable/juniIfTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	JuniMplsIfMajorEntry

juniMplsIfMajorIndex		1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.1
The ifIndex of the MPLS Major interface. When creating entries in this table, suitable values for this object are determined by reading juniMplsIfMajorNextIfIndex.
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndex

juniMplsIfMajorRowStatus		1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.2
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: juniMplsIfMajorRowStatus juniMplsIfMajorLowerIfIndex In addition, when creating an entry the following conditions must hold: A value for juniMplsIfMajorIndex must have been determined previously, by reading juniMplsIfMajorNextIfIndex. A corresponding entry in ifTable/ifXTable/juniIfTable is created/ destroyed as a result of creating/destroying an entry in this table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

juniMplsIfMajorLowerIfIndex		1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.3
The ifIndex of an interface over which this MPLS Major interface to be layered. A value of zero indicates no layering. An implementation may choose to require that a nonzero value be configured at entry creation.
Status: current	Access: read-create
OBJECT-TYPE
	InterfaceIndexOrZero

juniMplsIfMajorAdminStatus		1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.4
Use this object to create MPLS major interface stacked over any link layer interface. Lower layer(index) over which major stacks has to be specified for successful creation of the major interface.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

juniMplsIfMajorLdpAdminStatus		1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.5
This object enables/disables LDP admin status on the MPLS interface.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

juniMplsIfMajorLdpProfileName		1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.6
All the LDP settings on the MPLS interface be will associated with the profile. This object allows to associate those configured settings to interface by using the LDP profile name.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..20)

juniMplsIfMajorLdpVpiStart		1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.7
This object is defined to support configurations of interface label space. This configures the start range of the LDP VPI. For successful configuration of interface label space LDP VPI ranges, set this object with the stop range cunncurrently.
Status: current	Access: read-create
OBJECT-TYPE
	JuniMajorCfgVpiRanges

juniMplsIfMajorLdpVpiStop		1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.8
This object is defined to support configurations of interface label space. This configures the stop range of the LDP VPI. For successful configuration of interface label space LDP VPI ranges, set this object with the start range cunncurrently.
Status: current	Access: read-create
OBJECT-TYPE
	JuniMajorCfgVpiRanges

juniMplsIfMajorLdpVciStart		1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.9
This object is defined to support configurations of interface label space. This configures the start range of the LDP VCI. For successful configuration of interface label space LDP VCI ranges, set this object with the stop range cunncurrently.
Status: current	Access: read-create
OBJECT-TYPE
	JuniMajorCfgVciRanges

juniMplsIfMajorLdpVciStop		1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.10
This object is defined to support configurations of interface label space. This configures the stop range of the LDP VCI. For successful configuration of interface label space LDP VCI ranges, set this object with the start range cunncurrently.
Status: current	Access: read-create
OBJECT-TYPE
	JuniMajorCfgVciRanges

juniMplsIfMajorRsvpAdminStatus		1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.11
This object configures RSVP admin status for MPLS interface.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

juniMplsIfMajorRsvpProfileName		1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.12
All the RSVP settings on the MPLS interface be will associated with the profile. This object allows to associate those configured settings to interface by using the RSVP profile name.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..20)

juniMplsIfMajorRsvpVpiStart		1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.13
This object is defined to support configurations of interface label space. This configures the start range of the RSVP VPI. For successful configuration of interface label space RSVP VPI ranges, set this object with the stop range cunncurrently.
Status: current	Access: read-create
OBJECT-TYPE
	JuniMajorCfgVpiRanges

juniMplsIfMajorRsvpVpiStop		1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.14
This object is defined to support configurations of interface label space. This configures the stop range of the RSVP VPI. For successful configuration of interface label space RSVP VPI ranges, set this object with the start range cunncurrently.
Status: current	Access: read-create
OBJECT-TYPE
	JuniMajorCfgVpiRanges

juniMplsIfMajorRsvpVciStart		1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.15
This object is defined to support configurations of interface label space. This configures the start range of the RSVP VCI. For successful configuration of interface label space RSVP VCI ranges, set this object with the stop range cunncurrently.
Status: current	Access: read-create
OBJECT-TYPE
	JuniMajorCfgVciRanges

juniMplsIfMajorRsvpVciStop		1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.16
This object is defined to support configurations of interface label space. This configures the stop range of the RSVP VCI. For successful configuration of interface label space RSVP VCI ranges, set this object with the start range cunncurrently.
Status: current	Access: read-create
OBJECT-TYPE
	JuniMajorCfgVciRanges

juniMplsIfMajorLabelSpaceType		1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.17
Displays the label space type for the MPLS interface.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(0), rsvpVpiVci(1), rsvpVpi(2), rsvpVci(3), ldpVpiVci(4), ldpVpi(5), ldpVci(6)

juniMplsIfMajorOpState		1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.18
This object displays MPLS major interface operation state.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	lowerLayerNotAvailable(0), lowerLayerDown(1), up(2), configIncompleteInterfaceEnabled(3), configIncompleteInterfaceDisabled(4), interfaceDisabled(5)

juniMplsIfMajorCrLdpAdminState		1.3.6.1.4.1.4874.2.2.54.1.2.1.2.1.19
This object displays the admin state of CR-LDP.
Status: obsolete	Access: read-only
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

juniMplsIfMinorNextIfIndex		1.3.6.1.4.1.4874.2.2.54.1.3.1.1
Coordinates ifIndex value allocation for entries in the juniMplsIfMinorTable. A GET of this object returns the next available ifIndex value to be used to create an entry in the associated interface table; or zero, if no valid ifIndex value is available. This object also returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that ifIndex allocation is unintended. Successive GETs will typically return different values, thus avoiding collisions among cooperating management clients seeking to create table entries simultaneously.
Status: current	Access: read-only
OBJECT-TYPE
	JuniNextIfIndex

juniMplsIfMinorTable		1.3.6.1.4.1.4874.2.2.54.1.3.1.2
This table contains entries for MPLS Minor interfaces present in the system.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		JuniMplsIfMinorEntry

juniMplsIfMinorEntry		1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1
Each entry describes the characteristics of an MPLS Minor interface. Creating/deleting entries in this table causes corresponding entries for be created/deleted in ifTable/ifXTable/juniIfTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	JuniMplsIfMinorEntry

juniMplsIfMinorIndex		1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.1
The ifIndex of the MPLS Minor interface. When creating entries in this table, suitable values for this object are determined by reading juniMplsMinorNextIfIndex.
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndex

juniMplsIfMinorRowStatus		1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.2
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create/delete an entry in this table, the following entry objects MUST be explicitly configured: juniMplsIfMinorRowStatus juniMplsIfMinorTunnelName In addition, when creating an entry the following conditions must hold: A value for juniMplsIfMinorIndex must have been determined previously, by reading juniMplsMinorNextIfIndex. A corresponding entry in ifTable/ifXTable/juniIfTable is created/ destroyed as a result of creating/destroying an entry in this table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

juniMplsIfMinorLowerIfIndex		1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.3
The ifIndex of an interface over which this MPLS Minor interface is to be layered. A value of zero indicates no layering. As minor interface can be created without stacking on major interface, as and when it stacks on major interface by signalling protocol, it's value can be read.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndexOrZero

juniMplsIfMinorAdminStatus		1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.4
With this object minor interface admin status can be enabled/disabled.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

juniMplsIfMinorEndpointAddress		1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.5
This object configures the IP address of the tunnel destination. This object can be set along with the juniMplsIfMinorEndpointDstMask to configure the tunnel destination mask, but it is optional.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

juniMplsIfMinorEndpointDstMask		1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.6
This object configures the tunnel destination mask. It can be set along with the juniMplsIfMinorEndpointAddress.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

juniMplsIfMinorTunnelMetricMode		1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.7
Select the relative or absolute mode to configure the absolute or relative tunnel metric. To set the tunnel to relative metric, juniMplsIfMinorRelativeTunnelMetric has to be set along with this object option as relative. To set the tunnel to absolute metric, juniMplsIfMinorAbsoluteTunnelMetric has to be set along with this object option as absolute.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	absolute(0), relative(1)

juniMplsIfMinorAbsoluteTunnelMetric		1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.8
This object allows configuration of absolute metric values. Refer to juniMplsIfMinorTunnelMetricMode for how set it.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	1..4294967295

juniMplsIfMinorRelativeTunnelMetric		1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.9
This object allows configuration of relative metric values. Refer to juniMplsIfMinorTunnelMetricMode for how set it.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	-10..10

juniMplsIfMinorLabelDistProto		1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.10
This object allows to select label distribution protocol. Label distribution protocols are used by two LSRs to negotiate label to FEC binding to set up tunnels.
Status: obsolete	Access: read-create
OBJECT-TYPE
	INTEGER	crLdp(0), rsvpTe(1), undefined(2)

juniMplsIfMinorAnnounceToOspf		1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.11
This object allows to register LSP endpoints to OSPF to next hop calculation.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

juniMplsIfMinorAnnounceToIsis		1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.12
This object allows to register LSP endpoints to IS-IS for next hop calculation.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

juniMplsIfMinorAnnounceToBgp		1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.13
This object allows to register LSP endpoints to BGP for next hop calculation.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

juniMplsIfMinorBandwidth		1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.14
This object allows configuration of bandwidth requirements for the tunnel.
Status: current	Access: read-create
OBJECT-TYPE
	JuniMinorCfgBWRanges

juniMplsIfMinorAffinity		1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.15
This object allows configuration of resource class affinity for the tunnel.
Status: current	Access: read-create
OBJECT-TYPE
	OCTET STRING	Size(0..4)

juniMplsIfMinorAffinityMask		1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.16
This allows to set the resource class affinity mask. Since it is a mask, set along with the affinity for successful configurations.
Status: current	Access: read-create
OBJECT-TYPE
	OCTET STRING	Size(0..4)

juniMplsIfMinorSetupPriority		1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.17
This object allows configuration of preemption setup priority for the tunnel before and after it has been established. Lower the value higher the priority.
Status: current	Access: read-create
OBJECT-TYPE
	JuniMinorCfgHoldingAndSetupPriorityRanges

juniMplsIfMinorHoldingPriority		1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.18
This object allows configuration of the preemption holding priority for the tunnel before and after it has been established. Lower the value higher the priority.
Status: current	Access: read-create
OBJECT-TYPE
	JuniMinorCfgHoldingAndSetupPriorityRanges

juniMplsIfMinorTunnelName		1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.19
This object allows configuration of the tunnel name to be associated with tunnel settings.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..20)

juniMplsIfMinorTunnelRetryTimes		1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.20
This object allows configuration of the number of retries for tunnel setup.
Status: current	Access: read-create
OBJECT-TYPE
	JuniMinorCfgRetryTimesAndNorouteRanges

juniMplsIfMinorTunnelRetryInterval		1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.21
This object allows configuration of retry interval for tunnel setup.
Status: current	Access: read-create
OBJECT-TYPE
	JuniMinorCfgRetryIntervalAndNorouteRanges

juniMplsIfMinorTunnelRetryTimesNoroute		1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.22
This object allows configuration of the tunnel retries when no route notifications are received.
Status: current	Access: read-create
OBJECT-TYPE
	JuniMinorCfgRetryTimesAndNorouteRanges

juniMplsIfMinorTunnelRetryIntervalNoroute		1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.23
This object allows configuration of the tunnel retry interval when no route notifications are received.
Status: current	Access: read-create
OBJECT-TYPE
	JuniMinorCfgRetryIntervalAndNorouteRanges

juniMplsIfMinorBaseTunnelName		1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.24
This object allows configuration of the base tunnel name over which all the tunnels are stacked over.
Status: obsolete	Access: read-create
OBJECT-TYPE
	DisplayString

juniMplsIfMinorVpnOuiNumber		1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.25
This object allows configuration of the OUI part of VPN ID.
Status: obsolete	Access: read-create
OBJECT-TYPE
	Integer32	0..16777215

juniMplsIfMinorVpnIndex		1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.26
This object allows configuration of the index part of VPN ID.
Status: obsolete	Access: read-create
OBJECT-TYPE
	IpAddress

juniMplsIfMinorTunnelOpState		1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.27
This object displays the tunnel operation state. established : Tunnel established teNegotiation : TE Negotiation up : Tunnel Up down : Tunnel Down cfgChanged : Tunnel config changed cfgIncEn : Tunnel incomplete Config Admin State Enable cfgIncDis : Tunnel incomplete Config Admin State Disable disabled : Tunnel disabled rel : noChange : Tunnel state no change
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	established(0), teNegotiation(1), up(2), down(3), cfgChanged(4), cfgIncEn(5), cfgIncDis(6), disabled(7), rel(8), noChange(9)

juniMplsIfMinorTargetedDynamicTunnel		1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.28
Configure targeted dynamic tunnel.
Status: obsolete	Access: read-create
OBJECT-TYPE
	TruthValue

juniMplsIfMinorReoptimization		1.3.6.1.4.1.4874.2.2.54.1.3.1.2.1.29
Configure tunnel reoptimization.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

juniMplsIfMinorPathOptionTable		1.3.6.1.4.1.4874.2.2.54.1.3.2.1
Table is a list of different LSP paths as option for each LSP setup.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		JuniMplsIfMinorPathOptionEntry

juniMplsIfMinorPathOptionEntry		1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1
Each entry represents one path option for the LSP.
Status: current	Access: not-accessible
OBJECT-TYPE
	JuniMplsIfMinorPathOptionEntry

juniMplsIfMinorPathOptionIndex		1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.1
Minor interface unique ID.
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndex

juniMplsIfMinorPathOptionNumber		1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.2
Unique number to identify each path option configured.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..1000

juniMplsIfMinorPathOptionProtocol		1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.3
Select the each path option explicit routing protocol.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	hopByHop(0), isis(1), ospf(2), none(3)

juniMplsIfMinorPathOptionLockdown		1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.4
Enable/disable each configured path option reoptimization.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

juniMplsIfMinorPathOptionPathName		1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.5
Configure the name for each path option.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..20)

juniMplsIfMinorPathOptionPathId		1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.6
Configure the path option ID. Either the name or ID will be associated with a path at a time. If the path name and ID are set at a same time for the path, the name will have precedence over ID.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..65535

juniMplsIfMinorPathOptionRowStatus		1.3.6.1.4.1.4874.2.2.54.1.3.2.1.1.7
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: juniMplsIfMinorPathOptionRowStatus.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

juniMplsTunnelProfileTable		1.3.6.1.4.1.4874.2.2.54.1.4.1.1
Table is a list of tunnel profiles for a given VR.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		JuniMplsTunnelProfileEntry

juniMplsTunnelProfileEntry		1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1
Each entry represents one tunnel profile.
Status: current	Access: not-accessible
OBJECT-TYPE
	JuniMplsTunnelProfileEntry

juniMplsTunnelProfileName		1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.1
Associate a name for the configured tunnel profile settings.
Status: current	Access: not-accessible
OBJECT-TYPE
	DisplayString	Size(0..20)

juniMplsTunnelProfileAdminStatus		1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.2
Enable/disable the adminstatus of the tunnel profile.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

juniMplsTunnelProfileBaseTunnelName		1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.3
Configure the base tunnel name in tunnel profile settings. This base tunnel is the one over which all the other tunnels are stacked over. Configured base tunnel name in profile settings will be associated with the actual configured base tunnel name.
Status: obsolete	Access: read-create
OBJECT-TYPE
	DisplayString

juniMplsTunnelProfileIpProfileName		1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.4
Configures the name for IP profile settings for the IP interfaces over which MPLS tunnels are stacked.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..20)

juniMplsTunnelProfileLabelDistProto		1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.5
Configure the label distribution protocol to associate with a tunnel profile. Label distribution protocols are used by two LSRs to negotiate label to FEC binding to set up tunnels.
Status: obsolete	Access: read-create
OBJECT-TYPE
	INTEGER	crLdp(0), rsvpTe(1), undefined(2)

juniMplsTunnelProfileAnnounceToOspf		1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.6
Configure the routing protocol for next hop calculations as OSPF.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

juniMplsTunnelProfileAnnounceToIsis		1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.7
Configure routing protocol for next hop calculations as ISIS.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

juniMplsTunnelProfileAnnounceToBgp		1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.8
Configure routing protocol for next hop calculations as BGP.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

juniMplsTunnelProfileMetricMode		1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.9
Select the relative or absolute mode to configure the absolute or relative tunnel profile metric. To set the tunnel profile to relative metric, juniMplsTunnelProfileRelativeMetric has to be set along with this object option as relative. To set the tunnel profile to absolute metric, juniMplsTunnelProfileAbsoluteMetric has to be set along with this object option as absolute.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	absolute(0), relative(1)

juniMplsTunnelProfileAbsoluteMetric		1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.10
This object allows configuration of the absolute metric values. Refer to juniMplsTunnelProfileMetricMode for how set it.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	1..4294967295

juniMplsTunnelProfileRelativeMetric		1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.11
This object allows configuration of the relative metric values. Refer to juniMplsTunnelProfileMetricMode for how set it.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	-10..10

juniMplsTunnelProfileBandwidth		1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.12
This object allows configuration of bandwidth requirements for the tunnel.
Status: current	Access: read-create
OBJECT-TYPE
	JuniProfileCfgBWRanges

juniMplsTunnelProfileAffinity		1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.13
This object allows configuration of the resource class affinity for the tunnel. This can set independently of juniMplsTunnelProfileAffinityMask.
Status: current	Access: read-create
OBJECT-TYPE
	OCTET STRING	Size(0..4)

juniMplsTunnelProfileAffinityMask		1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.14
This allows configuration of which bits in the affinity must match the resource class bits. Can't be set independently; always with juniMplsTunnelProfileAffinity. Specify the value in bit mask format.
Status: current	Access: read-create
OBJECT-TYPE
	OCTET STRING	Size(0..4)

juniMplsTunnelProfileSetupPriority		1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.15
This object configuration of the preemption setup priority for the tunnel before and after it has been established. Lower the value higher the priority.
Status: current	Access: read-create
OBJECT-TYPE
	JuniProfileCfgHoldingAndSetupPriorityRanges

juniMplsTunnelProfileHoldingPriority		1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.16
This object allows configuration of the preemption holding priority for the tunnel before and after it has been established. Lower the value higher the priority.
Status: current	Access: read-create
OBJECT-TYPE
	JuniProfileCfgHoldingAndSetupPriorityRanges

juniMplsTunnelProfileRetryTimes		1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.17
This object allows configuration of the number of retries for the tunnel setup.
Status: current	Access: read-create
OBJECT-TYPE
	JuniProfileCfgRetryTimesAndNorouteRanges

juniMplsTunnelProfileRetryInterval		1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.18
This object allows configuration of retry interval for tunnel setup.
Status: current	Access: read-create
OBJECT-TYPE
	JuniProfileCfgRetryIntervalAndNorouteRanges

juniMplsTunnelProfileRetryTimesNoroute		1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.19
This object allows configuration of the tunnel retries when no route notifications are received.
Status: current	Access: read-create
OBJECT-TYPE
	JuniProfileCfgRetryTimesAndNorouteRanges

juniMplsTunnelProfileRetryIntervalNoroute		1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.20
This object allows configuration of the tunnel retry interval when no route notifications are received.
Status: current	Access: read-create
OBJECT-TYPE
	JuniProfileCfgRetryIntervalAndNorouteRanges

juniMplsTunnelProfileVpnOuiNumber		1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.21
This object allows configuration of the OUI part of VPN ID.
Status: obsolete	Access: read-create
OBJECT-TYPE
	Integer32	0..16777215

juniMplsTunnelProfileVpnIndex		1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.22
This object allows configuration of the index part of VPN ID.
Status: obsolete	Access: read-create
OBJECT-TYPE
	IpAddress

juniMplsTunnelProfileRowStatus		1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.23
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: juniMplsTunnelProfileRowStatus
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

juniMplsTunnelProfileTargetedDynamicTunnel		1.3.6.1.4.1.4874.2.2.54.1.4.1.1.1.24
Configure targeted dynamic tunnel.
Status: obsolete	Access: read-create
OBJECT-TYPE
	TruthValue

juniMplsTunnelProfilePathOptionTable		1.3.6.1.4.1.4874.2.2.54.1.4.2.1
Table is a list of different LSP paths as option for each LSP setup, configured as part of tunnel profile settings
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		JuniMplsTunnelProfilePathOptionEntry

juniMplsTunnelProfilePathOptionEntry		1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1
Each entry represents one path option for the LSP setup, configured as a part of tunnel profile settings.
Status: current	Access: not-accessible
OBJECT-TYPE
	JuniMplsTunnelProfilePathOptionEntry

juniMplsTunnelProfileNamePathOption		1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.1
Name of the path option.
Status: current	Access: not-accessible
OBJECT-TYPE
	DisplayString	Size(0..20)

juniMplsTunnelProfilePathOptionNumber		1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.2
Unique identifier for the path option.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..1000

juniMplsTunnelProfilePathOptionProtocol		1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.3
Path selection option protocol.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	hopByHop(0), isis(1), ospf(2), none(3)

juniMplsTunnelProfilePathOptionLockdown		1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.4
Enable/disable path selection option reoptimization.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

juniMplsTunnelProfilePathOptionPathName		1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.5
Associate a name with each explicit path.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..20)

juniMplsTunnelProfilePathOptionPathId		1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.6
Each explicit path can be associated either name or ID. This object allows configuration of the ID for the explicit path.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..65535

juniMplsTunnelProfilePathOptionRowStatus		1.3.6.1.4.1.4874.2.2.54.1.4.2.1.1.7
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: juniMplsTunnelProfilePathOptionRowStatus.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

juniMplsTunnelProfileDynamicEndpointTable		1.3.6.1.4.1.4874.2.2.54.1.4.2.2
This table contains entries for the dynamic endpoints configured for each tunnel profile.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		JuniMplsTunnelProfileDynamicEndpointEntry

juniMplsTunnelProfileDynamicEndpointEntry		1.3.6.1.4.1.4874.2.2.54.1.4.2.2.1
Dynamic endpoint entries for each tunnel profile.
Status: current	Access: not-accessible
OBJECT-TYPE
	JuniMplsTunnelProfileDynamicEndpointEntry

juniMplsTunnelProfileNameDynamicEndpoint		1.3.6.1.4.1.4874.2.2.54.1.4.2.2.1.1
Configure the tunnel dynamic endpoint in tunnel profile settings.
Status: current	Access: not-accessible
OBJECT-TYPE
	DisplayString	Size(0..20)

juniMplsTunnelProfileDynamicEndpointType		1.3.6.1.4.1.4874.2.2.54.1.4.2.2.1.2
Configure the dynamic endpoint type for the tunnel.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	isisLevel2(0), ospfBorder(1)

juniMplsTunnelProfileDynamicEndpointPolicyListType		1.3.6.1.4.1.4874.2.2.54.1.4.2.2.1.3
This object allows configuration of the dynamic tunnel policy type selection.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	accessList(1), prefixList(2), noPolicyList(3)

juniMplsTunnelProfileDynamicEndpointListName		1.3.6.1.4.1.4874.2.2.54.1.4.2.2.1.4
This object allows configuration of the dynamic endpoints access list name.
Status: current	Access: not-accessible
OBJECT-TYPE
	DisplayString	Size(0..20)

juniMplsTunnelProfileDynamicEndpointRowStatus		1.3.6.1.4.1.4874.2.2.54.1.4.2.2.1.5
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry object MUST be explicitly configured: juniMplsTunnelProfileDynamicEndpointRowStatus.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

juniMplsTunnelProfileTunnelEndpointTable		1.3.6.1.4.1.4874.2.2.54.1.4.2.3
Table contains list of tunnel static enpoints configured for each tunnel profile.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		JuniMplsTunnelProfileTunnelEndpointEntry

juniMplsTunnelProfileTunnelEndpointEntry		1.3.6.1.4.1.4874.2.2.54.1.4.2.3.1
Each entry represents one static endpoint configuration for the tunnel.
Status: current	Access: not-accessible
OBJECT-TYPE
	JuniMplsTunnelProfileTunnelEndpointEntry

juniMplsTunnelProfileNameTunnelEndpoint		1.3.6.1.4.1.4874.2.2.54.1.4.2.3.1.1
This object configures the tunnel profile name.
Status: current	Access: not-accessible
OBJECT-TYPE
	DisplayString	Size(0..20)

juniMplsTunnelProfileTunnelEndpointAddress		1.3.6.1.4.1.4874.2.2.54.1.4.2.3.1.2
This object configures the IP address of the tunnel destination.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

juniMplsTunnelProfileTunnelEndpointDstMask		1.3.6.1.4.1.4874.2.2.54.1.4.2.3.1.3
This object configures the tunnel destination mask. A value of 255.255.255.255 is expected.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

juniMplsTunnelProfileTunnelEndpointRowStatus		1.3.6.1.4.1.4874.2.2.54.1.4.2.3.1.4
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: juniMplsTunnelProfileTunnelEndpointRowStatus.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

juniMplsExplicitPathTable		1.3.6.1.4.1.4874.2.2.54.1.5.1.1
Table is a list of hops configurations for explicit paths.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		JuniMplsExplicitPathEntry

juniMplsExplicitPathEntry		1.3.6.1.4.1.4874.2.2.54.1.5.1.1.1
Each entry represents one hop configuration for the particular explicit path.
Status: current	Access: not-accessible
OBJECT-TYPE
	JuniMplsExplicitPathEntry

juniMplsExplicitPathName		1.3.6.1.4.1.4874.2.2.54.1.5.1.1.1.1
Configure the name for the explicit path used as table index.
Status: current	Access: not-accessible
OBJECT-TYPE
	DisplayString	Size(0..20)

juniMplsExplicitPathAdminState		1.3.6.1.4.1.4874.2.2.54.1.5.1.1.1.2
Enable/disable explicit path adminstatus.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

juniMplsExplicitPathRowStatus		1.3.6.1.4.1.4874.2.2.54.1.5.1.1.1.3
Creation/deletion of the explicit path is done through setting this object.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

juniMplsExplicitPathNodeTable		1.3.6.1.4.1.4874.2.2.54.1.5.1.2
Table is a list of configured explicit paths.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		JuniMplsExplicitPathNodeEntry

juniMplsExplicitPathNodeEntry		1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1
Each entry represents one hop in a particular explicit path.
Status: current	Access: not-accessible
OBJECT-TYPE
	JuniMplsExplicitPathNodeEntry

juniMplsExplicitPathNodeName		1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1.1
Configure the name for the explicit path used in the table index.
Status: current	Access: not-accessible
OBJECT-TYPE
	DisplayString	Size(0..20)

juniMplsExplicitPathNodeIndexNumber		1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1.2
Each explicit path hop will have an index associated with it. Configure each path hop index using this object.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..255

juniMplsExplicitPathNodeLoose		1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1.3
Configure the explicit path hop as strict or loose. Set along with HopAddress.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

juniMplsExplicitPathNodeHopAddress		1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1.4
Configure the hop IP address to setup explicit path. Explicit path next hop will be created when the mentioned hop IP address doesn't belong to any of the existing hop even without setting the rowStatus createAndGo value. The rowStatus value is used to destroy the node.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

juniMplsExplicitPathNodeHopAddressMask		1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1.5
Configure the hop IP address mask. Set along with hop address.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

juniMplsExplicitPathNodeRowStatus		1.3.6.1.4.1.4874.2.2.54.1.5.1.2.1.6
Use this object for deletion of the node. For node creation, this value have no effect. Setting the node with IP address create the node. To delete the node set only this object.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

juniMplsConformance		1.3.6.1.4.1.4874.2.2.54.2
OBJECT IDENTIFIER

juniMplsCompliances		1.3.6.1.4.1.4874.2.2.54.2.1
OBJECT IDENTIFIER

juniMplsConfGroups		1.3.6.1.4.1.4874.2.2.54.2.2
OBJECT IDENTIFIER

juniMplsCompliance		1.3.6.1.4.1.4874.2.2.54.2.1.1
Obsolete compliance statement for entities which implement the Juniper MPLS MIB. This statement became obsolete when RowStatus support was added to some of the minor layer and tunnel profile tables.
Status: obsolete	Access: read-create
MODULE-COMPLIANCE

juniMplsCompliance2		1.3.6.1.4.1.4874.2.2.54.2.1.2
Obsolete compliance statement for entities which implement the Juniper MPLS MIB. This statement became obsolete when the juniMplsGroupIpTtlPropagate object was added to the juniMplsGroup scalar group.
Status: obsolete	Access: read-create
MODULE-COMPLIANCE

juniMplsCompliance3		1.3.6.1.4.1.4874.2.2.54.2.1.3
Obsolete compliance statement for entities which implement the Juniper MPLS MIB. This statement become obsolete when the objects juniMplsIfMajorCrLdpAdminState, juniMplsIfMinorLabelDistProto, juniMplsIfMinorBaseTunnelName, juniMplsIfMinorVpnOuiNumber, juniMplsIfMinorVpnIndex, juniMplsIfMinorTargetedDynamicTunnel, juniMplsTunnelProfileBaseTunnelName, juniMplsTunnelProfileLabelDistProto, juniMplsTunnelProfileVpnOuiNumber, juniMplsTunnelProfileVpnIndex, juniMplsTunnelProfileTargetedDynamicTunnel, juniMplsGroupLdpRetryTimesNoroute, juniMplsGroupLdpRetryTimes, juniMplsGroupLdpRetryIntervalNoroute and juniMplsGroupLdpProfileCrLdpAdminState became obsolete.
Status: obsolete	Access: read-create
MODULE-COMPLIANCE

juniMplsCompliance4		1.3.6.1.4.1.4874.2.2.54.2.1.4
The compliance statement for entities which implement the Juniper MPLS MIB.
Status: current	Access: read-create
MODULE-COMPLIANCE

juniMplsLsrGlobalConfGroup		1.3.6.1.4.1.4874.2.2.54.2.2.1
Obsolete collection of objects providing management of MPLS global configurations in a Juniper product. This group became obsolete when the object juniMplsGroupIpTtlPropagate was added.
Status: obsolete	Access: read-create
OBJECT-GROUP

juniMplsMajorLayerConfGroup		1.3.6.1.4.1.4874.2.2.54.2.2.2
A collection of objects providing management of major MPLS interfaces in a Juniper product. This group became obsolete when the object juniMplsIfMajorCrLdpAdminState became obsolete.
Status: obsolete	Access: read-create
OBJECT-GROUP

juniMplsMinorLayerConfGroup		1.3.6.1.4.1.4874.2.2.54.2.2.3
Obsolete collection of objects providing management of minor MPLS (tunnel) in a Juniper product. This group became obsolete when the juniMplsIfMinorPathOptionRowStatus object was added.
Status: obsolete	Access: read-create
OBJECT-GROUP

juniMplsTunnelProfileConfGroup		1.3.6.1.4.1.4874.2.2.54.2.2.4
Obsolete collection of objects providing management of MPLS tunnel profiles in a Juniper product. This group became obsolete when RowStatus objects were added to some of the tables.
Status: obsolete	Access: read-create
OBJECT-GROUP

juniMplsExplicitPathConfGroup		1.3.6.1.4.1.4874.2.2.54.2.2.5
A collection of objects providing management of MPLS explicit paths in a Juniper product.
Status: current	Access: read-create
OBJECT-GROUP

juniMplsMinorLayerConfGroup2		1.3.6.1.4.1.4874.2.2.54.2.2.6
A collection of objects providing management of minor MPLS (tunnel) interfaces in a Juniper product. This group became obsolete when the objects juniMplsIfMinorLabelDistProto, juniMplsIfMinorBaseTunnelName, juniMplsIfMinorVpnOuiNumber, juniMplsIfMinorVpnIndex, juniMplsIfMinorTargetedDynamicTunnel became obsolete.
Status: obsolete	Access: read-create
OBJECT-GROUP

juniMplsTunnelProfileConfGroup2		1.3.6.1.4.1.4874.2.2.54.2.2.7
A collection of objects providing management of MPLS tunnel profiles in a Juniper product. This group became oboslete when the objects juniMplsTunnelProfileBaseTunnelName, juniMplsTunnelProfileLabelDistProto, juniMplsTunnelProfileVpnOuiNumber, juniMplsTunnelProfileVpnIndex, juniMplsTunnelProfileTargetedDynamicTunnel became obsolete.
Status: obsolete	Access: read-create
OBJECT-GROUP

juniMplsLsrGlobalConfGroup2		1.3.6.1.4.1.4874.2.2.54.2.2.8
A collection of objects providing management of MPLS label switching routers (LSRs) in a Juniper product. This group became obsolete when the object juniMplsGroupLdpRetryTimesNoroute, juniMplsGroupLdpRetryIntervalNoroute, juniMplsGroupLdpRetryTimes and juniMplsGroupLdpProfileCrLdpAdminState became obsolete.
Status: obsolete	Access: read-create
OBJECT-GROUP

juniMplsLsrGlobalConfGroup3		1.3.6.1.4.1.4874.2.2.54.2.2.9
A collection of objects providing management of MPLS label switching routers (LSRs) in a Juniper product.
Status: current	Access: read-create
OBJECT-GROUP

juniMplsMajorLayerConfGroup2		1.3.6.1.4.1.4874.2.2.54.2.2.10
A collection of objects providing management of major MPLS interfaces in a Juniper product.
Status: current	Access: read-create
OBJECT-GROUP

juniMplsMinorLayerConfGroup3		1.3.6.1.4.1.4874.2.2.54.2.2.11
A collection of objects providing management of minor MPLS (tunnel) interfaces in a Juniper product.
Status: current	Access: read-create
OBJECT-GROUP

juniMplsTunnelProfileConfGroup3		1.3.6.1.4.1.4874.2.2.54.2.2.12
A collection of objects providing management of MPLS tunnel profiles in a Juniper product
Status: current	Access: read-create
OBJECT-GROUP