DGS3324SRi-SWL2MGMT-MIB
File:
DGS3324SRi-SWL2MGMT-MIB.mib (65839 bytes)
Imported modules
Imported symbols
Defined Types
SwDevModuleInfoEntry |
|
SEQUENCE |
|
|
|
|
swDevModuleInfoUnitID |
INTEGER |
|
|
swDevModuleInfoModuleName |
DisplayString |
|
|
swDevModuleInfoReversion |
DisplayString |
|
|
swDevModuleInfoSerial |
DisplayString |
|
|
swDevModuleInfoDescription |
DisplayString |
|
SwL2PortInfoEntry |
|
SEQUENCE |
|
|
|
|
swL2PortInfoPortIndex |
INTEGER |
|
|
swL2PortInfoUnitID |
INTEGER |
|
|
swL2PortInfoType |
INTEGER |
|
|
swL2PortInfoLinkStatus |
INTEGER |
|
|
swL2PortInfoNwayStatus |
INTEGER |
|
SwL2PortCtrlEntry |
|
SEQUENCE |
|
|
|
|
swL2PortCtrlPortIndex |
INTEGER |
|
|
swL2PortCtrlUnitIndex |
INTEGER |
|
|
swL2PortCtrlAdminState |
INTEGER |
|
|
swL2PortCtrlNwayState |
INTEGER |
|
|
swL2PortCtrlFlowCtrlState |
INTEGER |
|
|
swL2PortCtrlLockState |
INTEGER |
|
|
swL2PortCtrlMACNotifyState |
INTEGER |
|
SwL2QOSBandwidthControlEntry |
|
SEQUENCE |
|
|
|
|
swL2QOSBandwidthPortIndex |
INTEGER |
|
|
swL2QOSBandwidthRxRate |
INTEGER |
|
|
swL2QOSBandwidthTxRate |
INTEGER |
|
SwL2QOSSchedulingEntry |
|
SEQUENCE |
|
|
|
|
swL2QOSSchedulingClassIndex |
INTEGER |
|
|
swL2QOSSchedulingMaxPkts |
INTEGER |
|
|
swL2QOSSchedulingMechanism |
INTEGER |
|
SwL2QOS8021pUserPriorityEntry |
|
SEQUENCE |
|
|
|
|
swL2QOS8021pUserPriorityIndex |
INTEGER |
|
|
swL2QOS8021pUserPriorityClass |
INTEGER |
|
SwL2QOS8021pDefaultPriorityEntry |
|
SEQUENCE |
|
|
|
|
swL2QOS8021pDefaultPriorityIndex |
INTEGER |
|
|
swL2QOS8021pDefaultPriority |
INTEGER |
|
SwL2PortSecurityControlEntry |
|
SEQUENCE |
|
|
|
|
swL2PortSecurityPortIndex |
INTEGER |
|
|
swL2PortSecurityMaxLernAddr |
INTEGER |
|
|
swL2PortSecurityMode |
INTEGER |
|
|
swL2PortSecurityAdmState |
INTEGER |
|
SwL2TrunkCtrlEntry |
|
SEQUENCE |
|
|
|
|
swL2TrunkIndex |
INTEGER |
|
|
swL2TrunkName |
DisplayString |
|
|
swL2TrunkMasterPort |
INTEGER |
|
|
swL2TrunkMember |
PortList |
|
|
swL2TrunkFloodingPort |
INTEGER |
|
|
swL2TrunkType |
INTEGER |
|
|
swL2TrunkState |
RowStatus |
|
SwL2IGMPCtrlEntry |
|
SEQUENCE |
|
|
|
|
swL2IGMPCtrlVid |
INTEGER |
|
|
swL2IGMPQueryInterval |
INTEGER |
|
|
swL2IGMPMaxResponseTime |
INTEGER |
|
|
swL2IGMPRobustness |
INTEGER |
|
|
swL2IGMPLastMemberQueryInterval |
INTEGER |
|
|
swL2IGMPHostTimeout |
INTEGER |
|
|
swL2IGMPRouteTimeout |
INTEGER |
|
|
swL2IGMPLeaveTimer |
INTEGER |
|
|
swL2IGMPQueryState |
INTEGER |
|
|
swL2IGMPCurrentState |
INTEGER |
|
|
swL2IGMPCtrlState |
INTEGER |
|
|
swL2IGMPFastLeaveState |
INTEGER |
|
SwL2IGMPQueryInfoEntry |
|
SEQUENCE |
|
|
|
|
swL2IGMPInfoVid |
INTEGER |
|
|
swL2IGMPInfoQueryCount |
INTEGER |
|
|
swL2IGMPInfoTxQueryCount |
INTEGER |
|
SwL2IGMPInfoEntry |
|
SEQUENCE |
|
|
|
|
swL2IGMPVid |
INTEGER |
|
|
swL2IGMPGroupIpAddr |
IpAddress |
|
|
swL2IGMPMacAddr |
MacAddress |
|
|
swL2IGMPPortMap |
PortList |
|
|
swL2IGMPIpGroupReportCount |
INTEGER |
|
SwL2TrafficCtrlEntry |
|
SEQUENCE |
|
|
|
|
swL2TrafficCtrlGroupIndex |
INTEGER |
|
|
swL2TrafficCtrlUnitIndex |
INTEGER |
|
|
swL2TrafficCtrlBMStromthreshold |
INTEGER |
|
|
swL2TrafficCtrlBcastStromCtrl |
INTEGER |
|
|
swL2TrafficCtrlMcastStromCtrl |
INTEGER |
|
|
swL2TrafficCtrlDlfStromCtrl |
INTEGER |
|
SwL2TrafficSegEntry |
|
SEQUENCE |
|
|
|
|
swL2TrafficSegPort |
INTEGER |
|
|
swL2TrafficSegForwardPorts |
PortList |
|
Defined Values
swL2MgmtMIB |
1.3.6.1.4.1.171.11.59.4.2 |
The Structure of Layer 2 Network Management Information. |
MODULE-IDENTITY |
|
|
|
swL2DevMgmt |
1.3.6.1.4.1.171.11.59.4.2.1 |
OBJECT IDENTIFIER |
|
|
|
swL2QOSMgmt |
1.3.6.1.4.1.171.11.59.4.2.6 |
OBJECT IDENTIFIER |
|
|
|
swL2DevInfo |
1.3.6.1.4.1.171.11.59.4.2.1.1 |
OBJECT IDENTIFIER |
|
|
|
swDevInfoTotalNumOfPort |
1.3.6.1.4.1.171.11.59.4.2.1.1.1 |
The number of ports within this switch. This value is the sum
of the ports within this switch. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..65535 |
|
swDevInfoNumOfPortInUse |
1.3.6.1.4.1.171.11.59.4.2.1.1.2 |
The number of ports in this switch connected to the segment or
the end stations. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..65535 |
|
swDevModuleInfoEntry |
1.3.6.1.4.1.171.11.59.4.2.1.1.3.1 |
A list of management information for each unit in the system. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SwDevModuleInfoEntry |
|
|
swDevModuleInfoUnitID |
1.3.6.1.4.1.171.11.59.4.2.1.1.3.1.1 |
This object indicates the specific unit ID in the stacking/chassis
table. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
1..12 |
|
swDevModuleInfoSerial |
1.3.6.1.4.1.171.11.59.4.2.1.1.3.1.5 |
A textual string containing serial of the module. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
DisplayString |
Size(0..9) |
|
swL2DevCtrl |
1.3.6.1.4.1.171.11.59.4.2.1.2 |
OBJECT IDENTIFIER |
|
|
|
swL2DevCtrlStpState |
1.3.6.1.4.1.171.11.59.4.2.1.2.1 |
This object can be enabled or disabled spanning tree algorithm
during runtime of the system. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
other(1), disabled(2), enabled(3) |
|
swL2DevCtrlIGMPSnooping |
1.3.6.1.4.1.171.11.59.4.2.1.2.2 |
This object indicates layer 2 Internet Group Management
Protocol (IGMP) capture function is enabled or disabled. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
other(1), disabled(2), enabled(3) |
|
swL2DevCtrlRmonState |
1.3.6.1.4.1.171.11.59.4.2.1.2.3 |
This object can be enabled or disabled RMON. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
other(1), disabled(2), enabled(3) |
|
swL2DevCtrlCleanAllStatisticCounter |
1.3.6.1.4.1.171.11.59.4.2.1.2.4 |
As the object is set to active, all the statistic counters will
be cleared. If set to normal, do nothing. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
normal(1), active(2) |
|
swL2DevCtrlVlanIdOfFDBTbl |
1.3.6.1.4.1.171.11.59.4.2.1.2.5 |
Indicates the VLAN ID which the Dot1dTpFdbTable belongs to ;
The default value is DEFAULT_VLAN_ID of system . |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
VlanId |
|
|
swL2MACNotifyState |
1.3.6.1.4.1.171.11.59.4.2.1.2.6 |
This object can enabled or disabled MAC Notification. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
other(1), disabled(2), enabled(3) |
|
swL2MACNotifyHistorySize |
1.3.6.1.4.1.171.11.59.4.2.1.2.7 |
This object indicates the history size of variation MAC in address table.
The default value is 1 . |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
1..500 |
|
swL2MACNotifyInterval |
1.3.6.1.4.1.171.11.59.4.2.1.2.8 |
This object indicates the time interval in second for trigger the MAC notify message. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
1..2147483647 |
|
swL2DevCtrlAsymVlanState |
1.3.6.1.4.1.171.11.59.4.2.1.2.13 |
This object can enabl or disabl asymmetric vlan
during runtime of the system. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
other(1), disabled(2), enabled(3) |
|
swL2DevCtrlTelnetState |
1.3.6.1.4.1.171.11.59.4.2.1.2.14.1 |
This object control telnet status. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
other(1), disabled(2), enabled(3) |
|
swL2DevCtrlTelnetTcpPort |
1.3.6.1.4.1.171.11.59.4.2.1.2.14.2 |
This object can designate tcp port.
When telnet disable this object can't accessible. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
1..65535 |
|
swL2DevAlarm |
1.3.6.1.4.1.171.11.59.4.2.1.3 |
OBJECT IDENTIFIER |
|
|
|
swL2DevAlarmNewRoot |
1.3.6.1.4.1.171.11.59.4.2.1.3.1 |
When the device has become the new root of the Spanning Tree,
this object decide whether to send a new root trap. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
other(1), disabled(2), enabled(3) |
|
swL2DevAlarmTopologyChange |
1.3.6.1.4.1.171.11.59.4.2.1.3.2 |
This object determine to send a trap or not when the switch
topology was changed. If the object is enabled(3),
the topologyChange trap is sent by the device when any of its
configured ports transitions from the Learning state to the
Forwarding state, or from the Forwarding state to the Blocking
state. For the same port tranition, the device doesn't send the
trap if this object value is disabled or other. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
other(1), disabled(2), enabled(3) |
|
swL2DevAlarmLinkChange |
1.3.6.1.4.1.171.11.59.4.2.1.3.3 |
This object determine to send a trap or not when the link
was changed. If the object is enabled(3), the Link Change
trap is sent by the device when any of its ports link change.
The device doesn't send the trap if this object value is
disabled or other. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
other(1), disabled(2), enabled(3) |
|
swL2PortInfoTable |
1.3.6.1.4.1.171.11.59.4.2.3.1 |
A table that contains information about every port. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
SwL2PortInfoEntry |
|
swL2PortInfoEntry |
1.3.6.1.4.1.171.11.59.4.2.3.1.1 |
A list of information for each port of the device. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SwL2PortInfoEntry |
|
|
swL2PortInfoPortIndex |
1.3.6.1.4.1.171.11.59.4.2.3.1.1.1 |
This object indicates the module's port number.(1..Max port
number in the module) |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..65535 |
|
swL2PortInfoUnitID |
1.3.6.1.4.1.171.11.59.4.2.3.1.1.2 |
Indicates ID of the unit in the system |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..65535 |
|
swL2PortInfoType |
1.3.6.1.4.1.171.11.59.4.2.3.1.1.3 |
This object indicates the connector type of this port. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
portType-100Base-TX(1), portType-100Base-FX(2), portType-100Base-FL(3), portType-1000Base-TX(4), portType-1000Base-SX(5), portType-1000Base-LX(6), portType-1000Base-SX-GBIC(7), portType-1000Base-LX-GBIC(8), portType-1000Base-TX-GBIC(9), portType-1000Base-1394(10), portType-1000Base-TX-GBIC-COMBO(11), portType-1000Base-none-GBIC(12), portType-1000Base-SX-MGBIC(13), portType-1000Base-LX-MGBIC(14), portType-1000Base-TX-MGBIC(15), portType-1000Base-none-MGBIC(16), portType-SIO(17), portType-10G(18), portType-none(19) |
|
swL2PortInfoLinkStatus |
1.3.6.1.4.1.171.11.59.4.2.3.1.1.4 |
This object indicates the port link status. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
other(1), link-pass(2), link-fail(3) |
|
swL2PortInfoNwayStatus |
1.3.6.1.4.1.171.11.59.4.2.3.1.1.5 |
This object indicates the port speed and duplex mode. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
other(0), empty(1), link-down(2), half-10Mbps(3), full-10Mbps(4), half-100Mbps(5), full-100Mbps(6), half-1Gigabps(7), full-1Gigabps(8), full-10Gigabps(9) |
|
swL2PortCtrlTable |
1.3.6.1.4.1.171.11.59.4.2.3.2 |
A table that contains control information about every port. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
SwL2PortCtrlEntry |
|
swL2PortCtrlEntry |
1.3.6.1.4.1.171.11.59.4.2.3.2.1 |
A list of control information for each port of the device. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SwL2PortCtrlEntry |
|
|
swL2PortCtrlPortIndex |
1.3.6.1.4.1.171.11.59.4.2.3.2.1.1 |
This object indicates the module's port number.(1..Max port
number in the module) |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..65535 |
|
swL2PortCtrlUnitIndex |
1.3.6.1.4.1.171.11.59.4.2.3.2.1.2 |
Indicates ID of the unit in the device |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..65535 |
|
swL2PortCtrlAdminState |
1.3.6.1.4.1.171.11.59.4.2.3.2.1.3 |
This object decide the port enabled or disabled. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
other(1), disabled(2), enabled(3) |
|
swL2PortCtrlNwayState |
1.3.6.1.4.1.171.11.59.4.2.3.2.1.4 |
Chose the port speed, duplex mode, and N-Way function mode. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
other(1), nway-enabled(2), nway-disabled-10Mbps-Half(3), nway-disabled-10Mbps-Full(4), nway-disabled-100Mbps-Half(5), nway-disabled-100Mbps-Full(6), nway-disabled-1Gigabps-Half(7), nway-disabled-1Gigabps-Full(8), nway-disabled-1Gigabps-Full-master(9), nway-disabled-1Gigabps-Full-slave(10) |
|
swL2PortCtrlFlowCtrlState |
1.3.6.1.4.1.171.11.59.4.2.3.2.1.5 |
The flow control mechanism is different between full duplex
mode and half duplex mode. For half duplex mode, the jamming
signal is asserted. For full duplex mode, IEEE 802.3x flow
control function sends PAUSE frames and receives PAUSE frames. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
other(1), disabled(2), enabled(3) |
|
swL2PortCtrlLockState |
1.3.6.1.4.1.171.11.59.4.2.3.2.1.6 |
This object decide the port is locked or not. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
other(1), disabled(2), enabled(3) |
|
swL2PortCtrlMACNotifyState |
1.3.6.1.4.1.171.11.59.4.2.3.2.1.7 |
This object set each poet MAC notification state. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
other(1), disabled(2), enabled(3) |
|
swL2PortCtrlJumboFrame |
1.3.6.1.4.1.171.11.59.4.2.3.3 |
This object configure the switch's jumbo frame settings. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
other(1), disabled(2), enabled(3) |
|
swL2QOSBandwidthControlEntry |
1.3.6.1.4.1.171.11.59.4.2.6.1.1 |
A list of information contained in swL2QOSBandwidthControlTable. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SwL2QOSBandwidthControlEntry |
|
|
swL2QOSBandwidthPortIndex |
1.3.6.1.4.1.171.11.59.4.2.6.1.1.1 |
Indicates the port . |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
1..768 |
|
swL2QOSBandwidthRxRate |
1.3.6.1.4.1.171.11.59.4.2.6.1.1.2 |
Indicates RX Rate(Mbit/sec) of the specifed port. Value 10000 means no limit. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
1..10000 |
|
swL2QOSBandwidthTxRate |
1.3.6.1.4.1.171.11.59.4.2.6.1.1.3 |
Indicates TX Rate(Mbit/sec) of the specifed port. Value 10000 means no limit. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
1..10000 |
|
swL2QOSSchedulingEntry |
1.3.6.1.4.1.171.11.59.4.2.6.2.1 |
A list of information contained in swL2QOSSchedulingTable. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SwL2QOSSchedulingEntry |
|
|
swL2QOSSchedulingClassIndex |
1.3.6.1.4.1.171.11.59.4.2.6.2.1.1 |
Indicates the hardware queue number. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..7 |
|
swL2QOSSchedulingMaxPkts |
1.3.6.1.4.1.171.11.59.4.2.6.2.1.2 |
Indicates the maximum number of packets the hardware priority queue will be allowed
to transmit before allowing the next lowest priority queue to transmit its packets.
a value between 0 and 15 can be specified. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..15 |
|
swL2QOSSchedulingMechanism |
1.3.6.1.4.1.171.11.59.4.2.6.2.1.3 |
Indicates the mechanism of QOS scheduling. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
strict(1), roundrobin(2), weightfair(3) |
|
swL2QOS8021pUserPriorityEntry |
1.3.6.1.4.1.171.11.59.4.2.6.3.1 |
A list of information contained in swL2QOS8021pUserPriorityTable. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SwL2QOS8021pUserPriorityEntry |
|
|
swL2QOS8021pUserPriorityIndex |
1.3.6.1.4.1.171.11.59.4.2.6.3.1.1 |
The 802.1p user priority . |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..7 |
|
swL2QOS8021pUserPriorityClass |
1.3.6.1.4.1.171.11.59.4.2.6.3.1.2 |
The number of the switch's hardware priority queue. The switch has four hardware
priority queues available. They are numbered between 0 (the lowest priority)
and 6 (the highest priority). |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..6 |
|
swL2QOS8021pDefaultPriorityEntry |
1.3.6.1.4.1.171.11.59.4.2.6.4.1 |
A list of information contained in swL2QOS8021pDefaultPriorityTable. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SwL2QOS8021pDefaultPriorityEntry |
|
|
swL2QOS8021pDefaultPriority |
1.3.6.1.4.1.171.11.59.4.2.6.4.1.2 |
The priority value to assign to untagged packets received by the
switch ports on the switch.. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..7 |
|
swL2QOSSchedulingMechanismCtrl |
1.3.6.1.4.1.171.11.59.4.2.6.5 |
This object can control QOS scheduling Mechanism. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
strict(1), roundrobin(2), weightfair(3) |
|
swL2QOSHolPreventionCtrl |
1.3.6.1.4.1.171.11.59.4.2.6.6 |
Control QOS Hol Prevention |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
other(1), disabled(2), enabled(3) |
|
swL2PortSecurityControlTable |
1.3.6.1.4.1.171.11.59.4.2.7.1 |
port security feature which controls the address leaning capability and the
traffic forwarding decision. Each port can have this function enabled or disabled.
When it is enabled and a number is given said N, which allows N addresses to be
learned at this port, the first N learned addresses are locked at this port as
static entry. When the learned addresses number reach N, any coming packet with
not learned source addresses are discarded (e.g. dropped) and no more new addresses
can be learned at this port. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
SwL2PortSecurityControlEntry |
|
swL2PortSecurityControlEntry |
1.3.6.1.4.1.171.11.59.4.2.7.1.1 |
A list of information contained in swL2PortSecurityControlTable. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SwL2PortSecurityControlEntry |
|
|
swL2PortSecurityPortIndex |
1.3.6.1.4.1.171.11.59.4.2.7.1.1.1 |
Indicates the secured port to lock address learning. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
1..768 |
|
swL2PortSecurityMaxLernAddr |
1.3.6.1.4.1.171.11.59.4.2.7.1.1.2 |
Indicates allowable number of addresses to be learned at this port. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..65535 |
|
swL2PortSecurityMode |
1.3.6.1.4.1.171.11.59.4.2.7.1.1.3 |
Indicates the mode of locking address.
In deleteOnTimeout(3) mode - the locked addresses can be aged out after aging timer
expire. In this mode, when the locked address is aged
out, the number of address can be learned has to be
increased by one.
In deleteOnReset(4) mode - never age out the locked addresses unless restart
the system to prevent from port movement or intrusion. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
other(1), permanent(2), deleteOnTimeout(3), deleteOnReset(4) |
|
swL2PortSecurityAdmState |
1.3.6.1.4.1.171.11.59.4.2.7.1.1.4 |
Indicates administration state of locking address. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
other(1), enable(2), disable(3) |
|
swL2PortSecurityDelPort |
1.3.6.1.4.1.171.11.59.4.2.7.2.2 |
Indicates the port. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
1..768 |
|
swL2TrunkMaxSupportedEntries |
1.3.6.1.4.1.171.11.59.4.2.9.1 |
Maximum number of entries in the trunk configuration table
(swL2TrunkCtrlTable). |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..65535 |
|
swL2TrunkCurrentNumEntries |
1.3.6.1.4.1.171.11.59.4.2.9.2 |
Current actived number of entries in the trunk configuration
table. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..65535 |
|
swL2TrunkCtrlTable |
1.3.6.1.4.1.171.11.59.4.2.9.3 |
This table specifys which ports group a set of ports(up to 8)
into a single logical link. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
SwL2TrunkCtrlEntry |
|
swL2TrunkCtrlEntry |
1.3.6.1.4.1.171.11.59.4.2.9.3.1 |
A list of information specifies which ports group a set of
ports(up to 8) into a single logical link. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SwL2TrunkCtrlEntry |
|
|
swL2TrunkIndex |
1.3.6.1.4.1.171.11.59.4.2.9.3.1.1 |
The index of logical port trunk. The trunk group number depend
on the existence of unit and module. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..65535 |
|
swL2TrunkName |
1.3.6.1.4.1.171.11.59.4.2.9.3.1.2 |
The name of logical port trunk. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
DisplayString |
Size(0..12) |
|
swL2TrunkMasterPort |
1.3.6.1.4.1.171.11.59.4.2.9.3.1.3 |
The object indicates the master port number of the port trunk
entry. When using Port Trunk, you can not configure the other
ports of the group except the master port.
Their configuration must be same as the master port (e.g. speed,
duplex, enabled/disabled, flow control, and so on). |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
INTEGER |
1..65535 |
|
swL2TrunkMember |
1.3.6.1.4.1.171.11.59.4.2.9.3.1.4 |
Indicate how many number of ports is included in this Trunk.
The trunk port number depend on the existence of module.
The maximum number of ports is 8 for one trunks. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
PortList |
|
|
swL2TrunkFloodingPort |
1.3.6.1.4.1.171.11.59.4.2.9.3.1.5 |
The object indicates the flooding port number of the port trunk
entry. The first port of the trunk is implicitly configured to
be the flooding port. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
1..65535 |
|
swL2TrunkType |
1.3.6.1.4.1.171.11.59.4.2.9.3.1.6 |
This object indicated that type of the trunk group.
static : is static trunk group
lacp : is LACP trunk group . |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
INTEGER |
other(1), static(2), lacp(3) |
|
swL2TrunkState |
1.3.6.1.4.1.171.11.59.4.2.9.3.1.7 |
This object indicates the status of this entry. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
RowStatus |
|
|
swL2TrunkAlgorithm |
1.3.6.1.4.1.171.11.59.4.2.9.4 |
This object configures to part of the packet examined by the
switch when selecting the egress port for transmitting
load-sharing data. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
other(1), mac-source(2), mac-destination(3), mac-source-dest(4), ip-source(5), ip-destination(6), ip-source-dest(7) |
|
swL2MirrorLogicTargetPort |
1.3.6.1.4.1.171.11.59.4.2.10.1 |
This object indicates switch which port will sniff another
port. A trunk port member cannot be configured as a target
Snooping port. The port number is the sequential (logical)
number which is also applied to bridge MIB, etc. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..65535 |
|
swL2MirrorPortSourceIngress |
1.3.6.1.4.1.171.11.59.4.2.10.2 |
The represent the ingress into the source port packet to
sniffed. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
PortList |
|
|
swL2MirrorPortSourceEgress |
1.3.6.1.4.1.171.11.59.4.2.10.3 |
The represent the egress from the source port packet to
sniffed. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
PortList |
|
|
swL2MirrorPortState |
1.3.6.1.4.1.171.11.59.4.2.10.4 |
This object indicates the port mirroring state.
other(1) - this entry is currently in use but the conditions
under which it will remain so are different from each of the
following values.
disabled(2) - writing this value to the object, and then the
corresponding entry will be removed from the table.
enabled(3) - this entry is reside in the table. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
other(1), disabled(2), enabled(3) |
|
swL2IGMPMaxSupportedVlans |
1.3.6.1.4.1.171.11.59.4.2.11.1 |
Maximum number of Vlans in the layer 2 IGMP control table
(swL2IGMPCtrlTable). |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..65535 |
|
swL2IGMPMaxIpGroupNumPerVlan |
1.3.6.1.4.1.171.11.59.4.2.11.2 |
Maximum number of multicast ip group per Vlan in the layer 2
IGMP information table (swL2IGMPQueryInfoTable). |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..65535 |
|
swL2IGMPCtrlTable |
1.3.6.1.4.1.171.11.59.4.2.11.3 |
The table controls the Vlan's IGMP function. Its scale depends
on current VLAN state (swL2VlanInfoStatus). If VLAN is disabled
mode, there is only one entry in the table, with index 1. If
VLAN is in Port-Base or 802.1q mode, the number of entries can
be up to 12, with index range from 1 to 12. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
SwL2IGMPCtrlEntry |
|
swL2IGMPCtrlEntry |
1.3.6.1.4.1.171.11.59.4.2.11.3.1 |
The entry in IGMP control table (swL2IGMPCtrlTable). The entry
is effective only when IGMP capture switch
(swL2DevCtrlIGMPSnooping) is enabled. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SwL2IGMPCtrlEntry |
|
|
swL2IGMPCtrlVid |
1.3.6.1.4.1.171.11.59.4.2.11.3.1.1 |
This object indicates the IGMP control entry's VLAN id. If VLAN
is disabled, the Vid is always 0 and cannot be changed by
management users. If VLAN is in Port-Base mode, the Vid is
arranged from 1 to 12, fixed form. If VLAN is in 802.1q mode,
the Vid setting can vary from 1 to 4094 by management user, and
the Vid in each entry must be unique in the IGMP Control Table. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..65535 |
|
swL2IGMPQueryInterval |
1.3.6.1.4.1.171.11.59.4.2.11.3.1.2 |
The frequency at which IGMP Host-Query packets are
transmitted on this switch. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
1..65535 |
|
swL2IGMPMaxResponseTime |
1.3.6.1.4.1.171.11.59.4.2.11.3.1.3 |
The maximum query response time on this switch. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
1..25 |
|
swL2IGMPRobustness |
1.3.6.1.4.1.171.11.59.4.2.11.3.1.4 |
The Robustness Variable allows tuning for the expected
packet loss on a subnet. If a subnet is expected to be
lossy, the Robustness Variable may be increased. IGMP is
robust to (Robustness Variable-1) packet losses. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
1..255 |
|
swL2IGMPLastMemberQueryInterval |
1.3.6.1.4.1.171.11.59.4.2.11.3.1.5 |
The Last Member Query Interval is the Max Response Time
inserted into Group-Specific Queries sent in response to
Leave Group messages, and is also the amount of time between
Group-Specific Query messages. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
1..25 |
|
swL2IGMPHostTimeout |
1.3.6.1.4.1.171.11.59.4.2.11.3.1.6 |
The timer value for sending IGMP query packet when none was
sent by the host in the LAN. The timer works in per-VLAN basis.
Our device will be activated to send the query message if the
timer is expired. Please reference RFC2236-1997. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
1..16711450 |
|
swL2IGMPRouteTimeout |
1.3.6.1.4.1.171.11.59.4.2.11.3.1.7 |
The Router Timeout is how long a host must wait after hearing
a Query before it may send any IGMPv2 messages. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
1..16711450 |
|
swL2IGMPLeaveTimer |
1.3.6.1.4.1.171.11.59.4.2.11.3.1.8 |
When a querier receives a Leave Group message for a group that
has group members on the reception interface, it sends
Group-Specific Queries every swL2IGMPLeaveTimer to the group
being left. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
1..16711450 |
|
swL2IGMPQueryState |
1.3.6.1.4.1.171.11.59.4.2.11.3.1.9 |
This object decide the IGMP query enabled or disabled. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
other(1), disabled(2), enabled(3) |
|
swL2IGMPCurrentState |
1.3.6.1.4.1.171.11.59.4.2.11.3.1.10 |
This object indicates the current IGMP query state. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
other(1), querier(2), non-querier(3) |
|
swL2IGMPCtrlState |
1.3.6.1.4.1.171.11.59.4.2.11.3.1.11 |
This object indicates the status of this entry.
other(1) - this entry is currently in use but the conditions under
which it will remain so are different from each of the following
values.
disable(2) - IGMP funtion is disabled for this entry.
enable(3) - IGMP funtion is enabled for this entry. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
other(1), disable(2), enable(3) |
|
swL2IGMPFastLeaveState |
1.3.6.1.4.1.171.11.59.4.2.11.3.1.12 |
This object indicates the fast_leave status of this entry.
other(1) - this entry is currently in use but the conditions under
which it will remain so are different from each of the following
values.
disable(2) - IGMP fast-leave funtion is disabled for this entry.
enable(3) - IGMP fast-leave funtion is enabled for this entry. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
other(1), disable(2), enable(3) |
|
swL2IGMPQueryInfoTable |
1.3.6.1.4.1.171.11.59.4.2.11.4 |
The table contains the number current IGMP query packets which
is captured by this device, as well as the IGMP query packets
sent by the device. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
SwL2IGMPQueryInfoEntry |
|
swL2IGMPQueryInfoEntry |
1.3.6.1.4.1.171.11.59.4.2.11.4.1 |
Information about current IGMP query information, provided that
swL2DevCtrlIGMPSnooping and swL2IGMPCtrState of associated VLAN
entry are all enabled. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SwL2IGMPQueryInfoEntry |
|
|
swL2IGMPInfoVid |
1.3.6.1.4.1.171.11.59.4.2.11.4.1.1 |
This object indicates the Vid of associated IGMP info table
entry. It follows swL2IGMPCtrlVid in the associated entry of
IGMP control table (swL2IGMPCtrlTable). |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..65535 |
|
swL2IGMPInfoQueryCount |
1.3.6.1.4.1.171.11.59.4.2.11.4.1.2 |
This object indicates the number of query packets received
since the IGMP function enabled, in per-VLAN basis. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..65535 |
|
swL2IGMPInfoTxQueryCount |
1.3.6.1.4.1.171.11.59.4.2.11.4.1.3 |
This object indicates the send count of IGMP query messages, in
per-VLAN basis. In case of IGMP timer expiration, the switch
sends IGMP query packets to related VLAN member ports and
increment this object by 1. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..65535 |
|
swL2IGMPInfoTable |
1.3.6.1.4.1.171.11.59.4.2.11.5 |
The table containing current IGMP information which captured by
this device, provided that swL2DevCtrlIGMPSnooping and
swL2IGMPCtrlState of associated VLAN entry are all enabled. Note
that the priority of IGMP table entries is lower than Filtering
Table, i.e. if there is a table hash collision between the
entries of IGMP Table and Filtering Table inside the switch H/W
address table, then Filtering Table entry overwrite the
colliding entry of IGMP Table. See swL2FilterMgmt description
also. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
SwL2IGMPInfoEntry |
|
swL2IGMPInfoEntry |
1.3.6.1.4.1.171.11.59.4.2.11.5.1 |
Information about current IGMP information which captured by
this device, provided that swL2DevCtrlIGMPSnooping and
swL2IGMPCtrlState of associated VLAN entry are all enabled. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SwL2IGMPInfoEntry |
|
|
swL2IGMPVid |
1.3.6.1.4.1.171.11.59.4.2.11.5.1.1 |
This object indicates the Vid of individual IGMP table entry.
It shows the Vid of IGMP report information captured on
network. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..65535 |
|
swL2IGMPGroupIpAddr |
1.3.6.1.4.1.171.11.59.4.2.11.5.1.2 |
This object is identify group ip address which is captured from
IGMP packet, in per-Vlan basis. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
IpAddress |
|
|
swL2IGMPMacAddr |
1.3.6.1.4.1.171.11.59.4.2.11.5.1.3 |
This object is identify mac address which is corresponding
to swL2IGMPGroupIpAddr, in per-Vlan basis. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
MacAddress |
|
|
swL2IGMPPortMap |
1.3.6.1.4.1.171.11.59.4.2.11.5.1.4 |
This object indicates which ports are belong to the same
multicast group, in per-Vlan basis. Each multicast group has a
octect string to indicate with port map. The most significant
bit represents the lowest numbered port, and the least
significant bit represents the highest numbered port. Thus, each
port of the switch is represented by a single bit within the
value of this object. If that bit has a value of '1' then that
port is included in the set of ports; the port is not included
if its bit has a value of '0'(Note that the setting of the bit
corresponding to the port from which a frame is received is
irrelevant). The 4 octets is represent one unit port according
its logic port. If the unit less 32 port, the other port don't
care just fill zero. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
PortList |
|
|
swL2IGMPIpGroupReportCount |
1.3.6.1.4.1.171.11.59.4.2.11.5.1.5 |
This object indicate how much report packet was receive by our
device corresponding with this entry from IGMP function enabled,
in per-Vlan basis. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..65535 |
|
swL2TrafficCtrlEntry |
1.3.6.1.4.1.171.11.59.4.2.13.1.1 |
A list of information specifies the storm traffic control
configuration. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SwL2TrafficCtrlEntry |
|
|
swL2TrafficCtrlGroupIndex |
1.3.6.1.4.1.171.11.59.4.2.13.1.1.1 |
The index of logical port trunk. The trunk group number depend
on the existence of unit and module. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..65535 |
|
swL2TrafficCtrlUnitIndex |
1.3.6.1.4.1.171.11.59.4.2.13.1.1.2 |
Indicates ID of the unit in the device |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..65535 |
|
swL2TrafficCtrlBMStromthreshold |
1.3.6.1.4.1.171.11.59.4.2.13.1.1.3 |
This object to decide how much thousand packets per second
broadcast/multicast (depend on swL2TrafficCtrlBcastStromCtrl,
swL2TrafficCtrlMcastStromCtrl or swL2TrafficCtrlDlfStromCtrl
objects whether is enabled) will active storm control. Whenever
a port reaches its configured amount of packets in the one
second time interval, the device will start dropping that type
of packet, until the time interval has expired. Once the time
interval has expired, the device will start forwarding that type
of packet. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..255 |
|
swL2TrafficCtrlBcastStromCtrl |
1.3.6.1.4.1.171.11.59.4.2.13.1.1.4 |
This object indicates broadcast storm control function is
enabled or disabled. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
other(1), disabled(2), enabled(3) |
|
swL2TrafficCtrlMcastStromCtrl |
1.3.6.1.4.1.171.11.59.4.2.13.1.1.5 |
This object indicates multicast storm control function is
enabled or disabled. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
other(1), disabled(2), enabled(3) |
|
swL2TrafficCtrlDlfStromCtrl |
1.3.6.1.4.1.171.11.59.4.2.13.1.1.6 |
This object indicates destination lookup fail function is
enabled or disabled. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
other(1), disabled(2), enabled(3) |
|
swL2TrafficSegTable |
1.3.6.1.4.1.171.11.59.4.2.14.1 |
This table specifys the port just can forward traffic to the
specific port list. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
SwL2TrafficSegEntry |
|
swL2TrafficSegEntry |
1.3.6.1.4.1.171.11.59.4.2.14.1.1 |
A list of information specifies the port with its traffic
forward list. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SwL2TrafficSegEntry |
|
|
swL2TrafficSegPort |
1.3.6.1.4.1.171.11.59.4.2.14.1.1.1 |
The port number of the logical port. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..65535 |
|
swL2TrafficSegForwardPorts |
1.3.6.1.4.1.171.11.59.4.2.14.1.1.2 |
The port list that the specific port can forward traffic. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
PortList |
|
|
swL2Notify |
1.3.6.1.4.1.171.11.59.4.2.15.1 |
OBJECT IDENTIFIER |
|
|
|
swL2macNotification |
1.3.6.1.4.1.171.11.59.4.2.15.1.2.0.1 |
This trap indicates the mac addresses variation in address table . |
Status: current |
Access: read-write |
NOTIFICATION-TYPE |
|
|
|
swL2macNotifyInfo |
1.3.6.1.4.1.171.11.59.4.2.15.1.2.1.1 |
This object indicates the last time reboot information. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
OCTET STRING |
Size(0..1024) |
|