CENTILLION-BRIDGEGROUP-MIB
File:
CENTILLION-BRIDGEGROUP-MIB.mib (12422 bytes)
Imported modules
Imported symbols
Defined Types
BridgeGroupEntry |
|
SEQUENCE |
|
|
|
|
bridgeGroupIdentifier |
BridgeGroupId |
|
|
bridgeGroupStatus |
StatusIndicator |
|
|
bridgeGroupBaseType |
INTEGER |
|
|
bridgeGroupStpProtocol |
INTEGER |
|
|
bridgeGroupPortType |
INTEGER |
|
|
bridgeGroupNextPortIndex |
INTEGER |
|
|
bridgeGroupTbRifEnable |
EnableIndicator |
|
|
bridgeGroupTbRifRing |
INTEGER |
|
BridgeGroupPortEntry |
|
SEQUENCE |
|
|
|
|
bridgeGroupPortGroupId |
BridgeGroupId |
|
|
bridgeGroupPortIndex |
INTEGER |
|
|
bridgeGroupPortStatus |
StatusIndicator |
|
|
bridgeGroupPortIfIndex |
INTEGER |
|
|
bridgeGroupPortSpanMode |
INTEGER |
|
|
bridgeGroupPortFastStart |
EnableIndicator |
|
Defined Values
dot1dBaseGroupIdentifier |
1.3.6.1.4.1.930.2.1.2.24.1 |
The spanning tree group identifier for which the standard
bridging MIBS apply. Modifications of the spanning tree group
through the standard bridging MIBs effect this spanning tree
group only. This object is super governed by specific SET
community string. For example if a network management station
uses SET community string setcommunitystring@bg3, all
related SET requests will effect spanning tree group 3 only. |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
BridgeGroupId |
|
|
bridgeGroupTable |
1.3.6.1.4.1.930.2.1.2.24.2 |
A specific spanning tree group. A spanning tree group consists
of a number of bridging ports running the same spanning tree
protocol. |
Status: mandatory |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
BridgeGroupEntry |
|
bridgeGroupEntry |
1.3.6.1.4.1.930.2.1.2.24.2.1 |
An entry in the spanning tree group table. Spanning tree
groups are added by specifying a bridgeGroupIdentifier,
bridgeGroupBaseType, bridgeGroupStpProtocol and a
bridgeGroupPortType with a value of valid(1) in
bridgeGroupStatus. Entries may be deleted by specifying
an entry with an value of invalid(2) in bridgeGroupStatus. |
Status: mandatory |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
BridgeGroupEntry |
|
|
bridgeGroupIdentifier |
1.3.6.1.4.1.930.2.1.2.24.2.1.1 |
The unique spanning tree group identifier of this spanning
tree group. |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
BridgeGroupId |
|
|
bridgeGroupStatus |
1.3.6.1.4.1.930.2.1.2.24.2.1.2 |
The current status of the spanning tree group. Spanning tree
groups may be added by specifiying a valid status, and removed
by specifying an invalid status. |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
StatusIndicator |
|
|
bridgeGroupBaseType |
1.3.6.1.4.1.930.2.1.2.24.2.1.3 |
Indicates the type of bridging this spanning tree group is
performing.A value of none(1) implies that switching is
performed between ports in this spanning tree group. A value
of unknown(2) implies that some unknown bridging rules are
applied on the ports in this spanning tree group. Modifying
the bridgeGroupBaseType requires a complete reset of the
spanning tree group. This value must be specified during
spanning tree group creation. |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
none(1), unknown(2), transparent-only(3), sourceroute-only(4), srt(5), translation(6) |
|
bridgeGroupStpProtocol |
1.3.6.1.4.1.930.2.1.2.24.2.1.4 |
An indication of the version of the Spanning Tree Protocol
is being run, if the value of bridgeGroupBaseType is not
none(1). This field may be ignored if the bridgeGroupBaseType
value is none(1). |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
none(1), unknown(2), decLb100(3), ieee8021d(4), ibm(5) |
|
bridgeGroupPortType |
1.3.6.1.4.1.930.2.1.2.24.2.1.5 |
Indicates the type of the spanning tree group ports. This
value may only be altered if there are no spanning tree group
ports currentlyin the spanning tree group. This value must be
specified during spanning tree group creation. |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
unknown(1), token-ring(2), ethernet(3) |
|
bridgeGroupNextPortIndex |
1.3.6.1.4.1.930.2.1.2.24.2.1.6 |
The value of the next spanning tree group port number which
will be assigned by the switch. When adding spanning tree
group ports bridging mode, the specified bridgeGroupPortIndex
must match this value. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
bridgeGroupTbRifEnable |
1.3.6.1.4.1.930.2.1.2.24.2.1.7 |
Enables the learning of Rif's by Token Ring Transparent
Bridging spanning tree groups and processing of LE_ARP's for
route descrptors. |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
EnableIndicator |
|
|
bridgeGroupTbRifRing |
1.3.6.1.4.1.930.2.1.2.24.2.1.8 |
The value of the ring used for learning RIF's when
bridgeGroupTbRifEnable is set. |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..4095 |
|
bridgeGroupPortTable |
1.3.6.1.4.1.930.2.1.2.24.3 |
A table that contains information about each port that is
associated with this spanning tree group. |
Status: mandatory |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
BridgeGroupPortEntry |
|
bridgeGroupPortEntry |
1.3.6.1.4.1.930.2.1.2.24.3.1 |
A list of information for each port of the spanning tree
group. These entries are created and deleted by switch. |
Status: mandatory |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
BridgeGroupPortEntry |
|
|
bridgeGroupPortGroupId |
1.3.6.1.4.1.930.2.1.2.24.3.1.1 |
The spanning tree group identifier to which this port
belongs. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
BridgeGroupId |
|
|
bridgeGroupPortIndex |
1.3.6.1.4.1.930.2.1.2.24.3.1.2 |
The value of the instance of the dot1dBasePort object,
defined in the Bridge MIB, for the spanning tree group
port corresponding to this port. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
bridgeGroupPortStatus |
1.3.6.1.4.1.930.2.1.2.24.3.1.3 |
The current status of the spanning tree group port entry.
Spanning tree group ports is added or deleted when a virtual
segment port is added to or deleted from a virtual segment. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
StatusIndicator |
|
|
bridgeGroupPortIfIndex |
1.3.6.1.4.1.930.2.1.2.24.3.1.4 |
The value of the instance of the ifIndex object, defined
in MIB-II, for the interface corresponding to this port.
Spanning tree group ports are added by specifying the
ifIndex instance for the spanning tree group port. |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
bridgeGroupPortSpanMode |
1.3.6.1.4.1.930.2.1.2.24.3.1.5 |
In SR mode, this object determines how this port behaves
when presented with a Spanning Tree Explorer frame. The
value 'disabled(2)' indicates that the port will not accept
or send Spanning Tree Explorer packets; any STE packets
received will be silently discarded. The value 'forced(3)'
indicates the port will always accept and propagate Spanning
Tree Explorer frames. This allows a manually configured
Spanning Tree for this class of packet to be configured.
Note that unlike transparent bridging, this is not
catastrophic to the network if there are loops.
The value 'auto-span(1)' can only be returned by a bridge
that both implements the Spanning Tree Protocol and has use
of the protocol enabled on this port. The behavior of the
port for Spanning Tree Explorer frames is determined by the
state of dot1dStpPortState. If the port is in the 'forwarding'
state, the frame will be accepted or propagated. Otherwise,
it will be silently discarded.
In TB mode, this object provides the means to statically
configure a port to forwarding/blocking modes. 'disabled(2)'
indicates that the port is statically configured to blocking
mode. 'forced(3)' indicates that the port is statically
configured to forwarding mode. 'auto-span(1)' indicates that
STP protocol is running. |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
auto-span(1), disabled(2), forced(3) |
|
bridgeGroupPortFastStart |
1.3.6.1.4.1.930.2.1.2.24.3.1.6 |
When FastStart is enabled, a port uses the minimum of hello
time and forward delay time for transition from listening to
learning to forwarding state. Once the port is in forwarding
state, it will behave as a normal spanning tree port. |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
EnableIndicator |
|
|