AirPairv2cTrap-MIB
File:
AirPairv2cTrap-MIB.mib (27304 bytes)
Imported modules
Imported symbols
Defined Values
coldStartV2c |
1.3.6.1.4.1.7262.1.26.0.0 |
A coldStart trap signifies that the sending protocol entity
is reinitializing itself such that the agent's configuration
or the protocol entity implementation may be altered. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
linkDownV2c |
1.3.6.1.4.1.7262.1.26.0.1 |
A linkDown trap signifies that the sending protocol entity
recognizes a failure in one of the communication links
represented in the agent's configuration. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
linkUpV2c |
1.3.6.1.4.1.7262.1.26.0.2 |
A linkUp trap signifies that the sending protocol entity
recognizes that one of the communication links represented
in the agent's configuration has come up. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
explicitAuthenticationFailureV2c |
1.3.6.1.4.1.7262.1.26.0.3 |
Authentication of the peer AirPair node has failed. The
severity is critical, the probable cause is an incorrect
authentication configuration on AirPair faulty cable
between the modem and radio, and recommended course of
action is to check both ends of the link. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
autoNegotiationDuplexMismatchV2c |
1.3.6.1.4.1.7262.1.26.0.4 |
The AirPair ethernet interface has a mismatch in duplex. The
severity is major, the probable cause is an incorrect
configuration of the switch or router connected to AirPair,
or the AirPair autonegotion settings. The recommended course
of action is to check the connection. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
modemLossOfSignalLockFromDemodulatorV2c |
1.3.6.1.4.1.7262.1.26.0.5 |
Loss of signal lock from the demodulator. The severity is
critical, the probable cause is lost synchronization with
the far end, and recommended course of action is to check
the operational state of both ends of the link. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
modemUncorrectedBerThresholdExceededV2c |
1.3.6.1.4.1.7262.1.26.0.6 |
The uncorrected BER threshold has been exceeded. The severity is major,
the probable cause is physical interference in the air link
or misalignment of the radios or severe weather conditions,
and recommended course of action is to check the line of site
between the air pair nodes. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
modemModulatorPllLockFailureV2c |
1.3.6.1.4.1.7262.1.26.0.7 |
Modulator PLL failure. The severity is critical, the probable
cause a faulty modem card within AirPair, and recommended
course of action is to replace the modem unit. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
modemModulatorLossOfSyncBytesV2c |
1.3.6.1.4.1.7262.1.26.0.8 |
Loss of sync bytes at the input of the modulator. The severity
is critical, the probable cause is physical interference in the
air link, and recommended course of action is to check the line
of site between the air pair nodes. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
modemSnrBelowThresholdV2c |
1.3.6.1.4.1.7262.1.26.0.11 |
The demodulator SNR performance worse than programmed levels. The
severity is major, the probable cause is physical interference in the
air link path or misalignment of the radios or severe weather conditions,
and recommended course of action is to check the line of site between
the air pair nodes. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
radioPLDROLostLockV2c |
1.3.6.1.4.1.7262.1.26.0.12 |
The PLDRO/LO has lost lock on the radio. The severity is critical, the
probable cause a faulty radio unit within AirPair, and recommended course
of action is to replace the radio unit. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
radioLostCommunicationV2c |
1.3.6.1.4.1.7262.1.26.0.13 |
RS232 communication lost between AIRPAIR and the radio. The severity is
critical, the probable cause is a faulty cable between the modem and radio,
and recommended course of action is to check the connection. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
radioMismatchV2c |
1.3.6.1.4.1.7262.1.26.0.14 |
The radio connected to the AIRPAIR modem does not match the frequency
programmed into the modem unit. The severity is major, the probable cause
is an incorrectly programmed modem or an incorrect radio type connected to
the modem, and recommended course of action is to check the modem frequency
settings and radio hardware version number or serial number. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
radioPowerAmpV2c |
1.3.6.1.4.1.7262.1.26.0.15 |
The power amplifier on the radio is not operating within normal operating
specifications. The severity is critical, the probable cause a faulty radio
unit within AirPair, and recommended course of action is to replace the
radio unit. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
ifTxSynthUnlockedV2c |
1.3.6.1.4.1.7262.1.26.0.16 |
The IF card within the modem unit has a Transmit Synthesizer which is not
locked and as a result will not transmit. The severity is critical, the
probable cause an incorrectly programmed frequency setting in the modem
or a faulty IF card, and recommended course of action is to check frequency
setting in the modem or to replace the modem unit. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
ifRxSynthUnlockedV2c |
1.3.6.1.4.1.7262.1.26.0.17 |
The IF card within the modem unit has a Receive Synthesizer which is not
locked. The severity is critical, the probable cause an incorrectly
programmed frequency setting in the modem or a faulty IF card, and
recommended course of action is to check frequency setting in the modem
or to replace the modem unit. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
ttySessionCommencedV2c |
1.3.6.1.4.1.7262.1.26.0.18 |
A person has successfully gained access to the ascii management port (telnet,
local management port, or HTTP). The username is included in the Trap. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
ttySessionTerminatedV2c |
1.3.6.1.4.1.7262.1.26.0.19 |
A person has logged out of an ascii management port (telnet, local management
port, or HTTP). The username is included in the Trap. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
rslBelowThresholdV2c |
1.3.6.1.4.1.7262.1.26.0.20 |
The RSL has been detected below its minimum threshold. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
droppedFramesThresholdExceededV2c |
1.3.6.1.4.1.7262.1.26.0.21 |
The ethernet dropped frames threshold has been detected above its threshold value. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
bwUtilizationThresholdExceededV2c |
1.3.6.1.4.1.7262.1.26.0.22 |
The ethernet bandwidth threshold has been detected above its threshold value. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
explicitAuthFailureClearedV2c |
1.3.6.1.4.1.7262.1.26.0.23 |
The condition has cleared. The peer node is now authenticated. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
autoNegDuplexMismatchClearedV2c |
1.3.6.1.4.1.7262.1.26.0.24 |
The condition has cleared. The Ethernet connection is not experiencing
auto-negotiation duplex mismatch. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
lossOfSyncSigFromDemoClearedV2c |
1.3.6.1.4.1.7262.1.26.0.25 |
The condition has cleared. The demodulator is synchronized. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
uncorrectedBerThresExceededClearedV2c |
1.3.6.1.4.1.7262.1.26.0.26 |
The condition has cleared. The demodulator uncorrected BER is now below its minimum
threshold value. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
modemModPLLFailureClearedV2c |
1.3.6.1.4.1.7262.1.26.0.27 |
The condition has cleared. The modem PLL is not failing. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
modemModLossOfSyncBytesClearedV2c |
1.3.6.1.4.1.7262.1.26.0.28 |
The condition has cleared. The modem is not experiencing loss of synch bytes. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
snrBelowThresholdClearedV2c |
1.3.6.1.4.1.7262.1.26.0.31 |
The condition has cleared. SNR is now above its minimum threshold value. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
radioPLDROLostLockClearedV2c |
1.3.6.1.4.1.7262.1.26.0.32 |
The condition has cleared. The radio PLDRO/LO lost lock condition has cleared. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
radioLostCommunicationClearedV2c |
1.3.6.1.4.1.7262.1.26.0.33 |
The condition has cleared. RS232 communication has been re-establisted between
AIRPAIR and the radio. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
radioMismatchClearedV2c |
1.3.6.1.4.1.7262.1.26.0.34 |
The condtion has cleared. The radio matches the programmed parameters in the modem. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
radioPowerAmpClearedV2c |
1.3.6.1.4.1.7262.1.26.0.35 |
The condtion has cleared. The radio Power Amp is not in the failed state. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
ifTxSynthUnlockedClearedV2c |
1.3.6.1.4.1.7262.1.26.0.36 |
The condtion has cleared. The IF stage transmit synthesizer is now locked. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
ifRxSynthUnlockedClearedV2c |
1.3.6.1.4.1.7262.1.26.0.37 |
The condtion has cleared. The IF stage receive synthesizer is now locked. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
rslBelowThresholdClearedV2c |
1.3.6.1.4.1.7262.1.26.0.38 |
The condition has cleared. RSL is now above its minimum threshold. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
droppedFramesThresholdExceededClearedV2c |
1.3.6.1.4.1.7262.1.26.0.39 |
The condition has cleared.The ethernet dropped frames threshold is now
below its threshold value. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
bwUtilizationThresholdExceededClearedV2c |
1.3.6.1.4.1.7262.1.26.0.40 |
The condition has cleared. The ethernet bandwidth threshold is now below
its threshold value. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
rxIfCableLossExceededV2c |
1.3.6.1.4.1.7262.1.26.0.41 |
The Rx cable loss has exceeded limit. This trap is only valid when the
AirPair installation type is IDU-ODU split. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
rxIfCableLossExceededClearedV2c |
1.3.6.1.4.1.7262.1.26.0.42 |
The condition has cleared. The Rx cable loss is now within limit. This trap
is only valid when the AirPair installation type is IDU-ODU split |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
txIfCableLossExceededV2c |
1.3.6.1.4.1.7262.1.26.0.43 |
The Tx cable loss has exceeded limit. This trap is only valid when the AirPair
installation type is IDU-ODU split |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
txIfCableLossExceededClearedV2c |
1.3.6.1.4.1.7262.1.26.0.44 |
The condition has cleared. The Tx cable loss is now within limit. This trap is
only valid when the AirPair installation type is IDU-ODU split |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
fan1FailedV2c |
1.3.6.1.4.1.7262.1.26.0.45 |
The Fan1 has failed. This trap is only valid when the AirPair installation
type is IDU-ODU split |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
fan1FailedClearedV2c |
1.3.6.1.4.1.7262.1.26.0.46 |
The condition has cleared. The fan1 is running normally. This trap is only
valid when the AirPair installation type is IDU-ODU split |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
fan2FailedV2c |
1.3.6.1.4.1.7262.1.26.0.47 |
The Fan2 has failed. This trap is only valid when the AirPair installation
type is IDU-ODU split |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
fan2FailedClearedV2c |
1.3.6.1.4.1.7262.1.26.0.48 |
The condition has cleared. The fan2 is running normally. This trap is only valid
when the AirPair installation type is IDU-ODU split |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
modemCardMismatchedHardwareFirmwareV2c |
1.3.6.1.4.1.7262.1.26.0.49 |
The modem card has incompatible hardware and firmware. The firmware will not run properly on this card. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
modemCardMismatchedHardwareFirmwareClearedV2c |
1.3.6.1.4.1.7262.1.26.0.50 |
The condition has cleared. The modem card has compatible hardware and firmware. The firmware will run properly on this card. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
atpcConfigMismatchV2c |
1.3.6.1.4.1.7262.1.26.0.51 |
ATPC configuration mismatch in the Airpair systems. ATPC is
enabled at one system, but ATPC is not enabled at the other
system. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
atpcConfigMismatchClearedV2c |
1.3.6.1.4.1.7262.1.26.0.52 |
ATPC configuration mismatch in the Airpair systems is cleared.
Both systems enabled ATPC. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
radioHiPwrOptM1V2c |
1.3.6.1.4.1.7262.1.26.0.53 |
When hi-power radio is used, hi-power gate M1 drain current is
out of lower or upper limits. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
radioHiPwrOptM1ClearedV2c |
1.3.6.1.4.1.7262.1.26.0.54 |
When hi-power radio is used, hi-power gate M1 drain current
is between lower and upper limits. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
radioHiPwrOptM2V2c |
1.3.6.1.4.1.7262.1.26.0.55 |
When hi-power radio is used, hi-power gate M2 drain current is
out of lower or upper limits. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
radioHiPwrOptM2ClearedV2c |
1.3.6.1.4.1.7262.1.26.0.56 |
When hi-power radio is used, hi-power gate M2 drain current
is between lower and upper limits. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
radioHiPwrTxDetectorV2c |
1.3.6.1.4.1.7262.1.26.0.57 |
When hi-power radio is used, hi-power tx detector dBm value
is smaller than limit. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
radioHiPwrTxDetectorClearedV2c |
1.3.6.1.4.1.7262.1.26.0.58 |
When hi-power radio is used, hi-power tx detector dBm
value is not smaller than limit. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
sntpServersUnreachableV2c |
1.3.6.1.4.1.7262.1.26.0.59 |
Can't reach any of the sntp servers |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
rlsMismatchV2c |
1.3.6.1.4.1.7262.1.26.0.61 |
RLS mismatch |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
rlsMismatchClearedV2c |
1.3.6.1.4.1.7262.1.26.0.62 |
RLS mismatch cleared |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
rLSShutdownActivatedV2c |
1.3.6.1.4.1.7262.1.26.0.63 |
RLS shutdown is activated |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
frequencyFileInvalidV2c |
1.3.6.1.4.1.7262.1.26.0.65 |
When the executing frequency file is invalid,
this trap is generated. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
optionalParaNotEntFreqFileV2c |
1.3.6.1.4.1.7262.1.26.0.66 |
when the optional parameters are not entered in frequency file,
and the system boots up, this trap is generated. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
progRadioBandNotFoundFreqFileV2c |
1.3.6.1.4.1.7262.1.26.0.67 |
when the executing frequency file doesn't contain the info related to programmed
radio band, this trap is generated. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
redundancyNoAtpcSupportV2c |
1.3.6.1.4.1.7262.1.26.0.70 |
Radio does not support atpc |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
redundancyInvalidFirmwareV2c |
1.3.6.1.4.1.7262.1.26.0.72 |
Radio firmware on radio and on modem card mismatch |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
aamConfigMisMatchV2c |
1.3.6.1.4.1.7262.1.26.0.76 |
Automatic Adaptive modulation configuration mismatch |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
aamConfigMisMatchClearV2c |
1.3.6.1.4.1.7262.1.26.0.77 |
Automatic Adaptive modulation configuration mismatch cleared |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
aamQpskActiveV2c |
1.3.6.1.4.1.7262.1.26.0.78 |
Automatic Adaptive modulation running on QPSK modulation |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
aamQpskActiveClearedV2c |
1.3.6.1.4.1.7262.1.26.0.79 |
Automatic Adaptive modulation running on higher modulation |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
primaryRadioFaultyV2c |
1.3.6.1.4.1.7262.1.26.0.80 |
Primary radio is faulty. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
primaryRadioFaultyClearedV2c |
1.3.6.1.4.1.7262.1.26.0.81 |
primary radio is not faulty anymore. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
radioSerialNumberMismatchV2c |
1.3.6.1.4.1.7262.1.26.0.82 |
Redundancy, Radio Serial number mismatch. |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|