ATT-CNM-DS3-MIB
File:
ATT-CNM-DS3-MIB.mib (13735 bytes)
Imported modules
Imported symbols
Defined Types
AttCNMds3ConfigEntry |
|
SEQUENCE |
|
|
|
|
attCNMds3ConfigIndex |
INTEGER |
|
|
attCNMds3LineType |
INTEGER |
|
|
attCNMds3ZeroCoding |
INTEGER |
|
|
attCNMds3ErrorsMaxIntervals |
INTEGER |
|
|
attCNMds3ErrorsIntervalLen |
INTEGER |
|
AttCNMds3StatusEntry |
|
SEQUENCE |
|
|
|
|
attCNMds3StatusIndex |
INTEGER |
|
|
attCNMds3LineStatus |
INTEGER |
|
AttCNMds3ErrorsEntry |
|
SEQUENCE |
|
|
|
|
attCNMds3ErrorsIndex |
INTEGER |
|
|
attCNMds3ErrorsInterval |
INTEGER |
|
|
attCNMds3ErrorsTimeStamp |
INTEGER |
|
|
attCNMds3ErrorsLocalTime |
DisplayString |
|
|
attCNMds3LCVs |
Gauge |
|
|
attCNMds3LESs |
Gauge |
|
|
attCNMds3LSESs |
Gauge |
|
|
attCNMds3CVs |
Gauge |
|
|
attCNMds3ESs |
Gauge |
|
|
attCNMds3SESs |
Gauge |
|
|
attCNMds3SEFSs |
Gauge |
|
|
attCNMds3UASs |
Gauge |
|
Defined Values
att-2 |
1.3.6.1.4.1.74 |
OBJECT IDENTIFIER |
|
|
|
att-mgmt |
1.3.6.1.4.1.74.2 |
OBJECT IDENTIFIER |
|
|
|
att-cnm |
1.3.6.1.4.1.74.2.15 |
OBJECT IDENTIFIER |
|
|
|
attCNMds3ConfigTable |
1.3.6.1.4.1.74.2.15.4.1 |
A list of entries containing configuration
information for all DS3 interfaces managed by
this system. |
Status: mandatory |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
AttCNMds3ConfigEntry |
|
attCNMds3ConfigEntry |
1.3.6.1.4.1.74.2.15.4.1.1 |
An entry containing configuration information
for a particular DS3 interface. |
Status: mandatory |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
AttCNMds3ConfigEntry |
|
|
attCNMds3ConfigIndex |
1.3.6.1.4.1.74.2.15.4.1.1.1 |
A unique value for each DS3 interface. The interface
identified by a particular value of this index is
the same interface as identified by the same value
of an attCNMifConfigIndex object instance. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
attCNMds3LineType |
1.3.6.1.4.1.74.2.15.4.1.1.2 |
This variable indicates the variety of DS3 C-bit
application supported by this interface.
For SMDS, this variable will have the value
ds3ClearChannel, denoting that this interface supports
the clear-channel with C-bit usage unspecified as
specified by ANSI. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
other(1), ds3M23(2), ds3SYNTRAN(3), ds3CbitParity(4), ds3ClearChannel(5) |
|
attCNMds3ZeroCoding |
1.3.6.1.4.1.74.2.15.4.1.1.3 |
This variable describes the variety of zero
code suppression/substitution used on the DS3
interface its characteristics. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
ds3other(1), ds3B3ZS(2) |
|
attCNMds3ErrorsMaxIntervals |
1.3.6.1.4.1.74.2.15.4.1.1.4 |
This variable identifies the maximum number
of measurement intervals supported for the
error counts maintained by this DS3 interface
in the attCNMds3ErrorsTable. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
attCNMds3ErrorsIntervalLen |
1.3.6.1.4.1.74.2.15.4.1.1.5 |
This variable identifies the number of seconds
that make up one complete measurement interval for
the error counts maintained by this DS3 interface
in the attCNMds3ErrorsTable. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
attCNMds3StatusTable |
1.3.6.1.4.1.74.2.15.4.2 |
A list of entries containing status information
for all DS3 interfaces managed by this system. |
Status: mandatory |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
AttCNMds3StatusEntry |
|
attCNMds3StatusEntry |
1.3.6.1.4.1.74.2.15.4.2.1 |
An entry containing status information for a
particular DS3 interface. |
Status: mandatory |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
AttCNMds3StatusEntry |
|
|
attCNMds3StatusIndex |
1.3.6.1.4.1.74.2.15.4.2.1.1 |
A unique value for each DS3 interface. The interface
identified by a particular value of this index is
the same interface as identified by the same value
of an attCNMifConfigIndex object instance. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
attCNMds3LineStatus |
1.3.6.1.4.1.74.2.15.4.2.1.2 |
This variable indicates the most Line Status
of this interface. This object is a bit map
represented as a sum, therefore, it can represent
multiple failures (alarms) simultaneously. The
various bit positions are:
1 No Alarm Present
2 Yellow Alarm
4 Near End Alarm-Indication-Signal
8 Near End Loss-Of-Frame
16 Near End Loss-Of-Signal
For example, for an interface that has LOF and
LOS outstanding, this object will have a value
of 24. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
attCNMds3ErrorsTable |
1.3.6.1.4.1.74.2.15.4.3 |
A list of entries containing protocol error counts,
maintained during the specified measurement interval,
for all DS3 interfaces managed by this system. |
Status: mandatory |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
AttCNMds3ErrorsEntry |
|
attCNMds3ErrorsEntry |
1.3.6.1.4.1.74.2.15.4.3.1 |
An entry containing protocol error counts,
maintained during the specified measurement interval,
for a particular DS3 interface. |
Status: mandatory |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
AttCNMds3ErrorsEntry |
|
|
attCNMds3ErrorsIndex |
1.3.6.1.4.1.74.2.15.4.3.1.1 |
A unique value for each DS3 interface. The interface
identified by a particular value of this index is
the same interface as identified by the same value
of an attCNMifConfigIndex object instance. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
attCNMds3ErrorsInterval |
1.3.6.1.4.1.74.2.15.4.3.1.2 |
This variable identifies the measurement interval
number for which measurement is provided. It is a
number between 1 and XX, where 1 identifies the most
recently completed measurement interval and XX is
the least recently completed measurement interval.
The value of XX is specified by the
attCNMds3ErrorsMaxIntervals object given in the
attCNMds3ConfigTable.
The maximum length of each measurement interval is
specified by the attCNMds3ErrorsIntervalLen object
given in the attCNMds3ConfigTable. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
attCNMds3ErrorsTimeStamp |
1.3.6.1.4.1.74.2.15.4.3.1.3 |
The time stamp corresponding to the end of the
specified measurement interval, as measured in
seconds from 00:00:00 UTC (Coordinated Universal
Time) January 1, 1970. Any fraction is rounded up. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
attCNMds3ErrorsLocalTime |
1.3.6.1.4.1.74.2.15.4.3.1.4 |
The time stamp corresponding to the end of the
specified measurement interval. Any fraction is
rounded up. It is given as a printable ASCII string
showing the local time at the end of the interval. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
DisplayString |
Size(0..255) |
|
attCNMds3LCVs |
1.3.6.1.4.1.74.2.15.4.3.1.5 |
The counter associated with the number of Line
Code Violations encountered by a DS3 interface
during the specified measurement interval.
For a B3ZS-coded signal, a Line Code Violation is
the occurrence of a received bipolar violation that
is not part of a zero-substitution code. For a B3ZS
signal, an LCV may also include other error patterns
such as: three consecutive zeros and incorrect parity.
The Bipolar Violation Rate is generally viewed as
approximating the Bit Error Rate. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Gauge |
|
|
attCNMds3LESs |
1.3.6.1.4.1.74.2.15.4.3.1.6 |
The counter associated with the number of Line
Errored Seconds encountered by a DS3 interface
during the specified measurement interval.
A Line Errored Second is any second with at least
one Line Code Violation. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Gauge |
|
|
attCNMds3LSESs |
1.3.6.1.4.1.74.2.15.4.3.1.7 |
The counter associated with the number of Line
Severely Errored Seconds encountered by a DS3
interface during the specified measurement interval.
A Line Severely Errored Second is any second with
45 or more Line Code Violations monitored at the
DS3 rate. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Gauge |
|
|
attCNMds3CVs |
1.3.6.1.4.1.74.2.15.4.3.1.8 |
The counter associated with the number of Code
Violations encountered by a DS3 interface during
the specified measurement interval.
For SMDS, a DS3 Code Violation is an occurrence of
a P-bit error. Excessive Coding Violations signifies
a faulty transmission line. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Gauge |
|
|
attCNMds3ESs |
1.3.6.1.4.1.74.2.15.4.3.1.9 |
The counter associated with the number of Errored
Seconds encountered by a DS3 interface during the
specified measurement interval.
For SMDS DS3 signals, this is the number of seconds
during which at least one error occurred which is a
P-bit error or a Severely Errored Framing event. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Gauge |
|
|
attCNMds3SESs |
1.3.6.1.4.1.74.2.15.4.3.1.10 |
The counter associated with the number of Severely
Errored Seconds encountered by a DS3 interface
during the specified measurement interval.
For SMDS DS3 signals, this is the number of seconds
during which 44 or more P-bit errors occurred or at
least one Severely Errored Framing event occurred.
All Severely Errored Seconds are also counted as
Errored Seconds. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Gauge |
|
|
attCNMds3SEFSs |
1.3.6.1.4.1.74.2.15.4.3.1.11 |
The counter associated with the number of Severely
Errored Framing Seconds encountered by a DS3
interface during the specified measurement interval.
A Severely Errored Framing Second is any second
during which one or more Severely Errored Framing
(SEF) events occurred. A Severely Errored Framing
event is declared when 3 or more errors in 16 or fewer
consecutive F-bits occur within a DS3 M-frame. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Gauge |
|
|
attCNMds3UASs |
1.3.6.1.4.1.74.2.15.4.3.1.12 |
The counter associated with the number of
Unavailable Seconds encountered by a DS3
interface during the specified measurement interval.
An Unavailable Second is any second during which
the DS3 interface was unavailable to offer service. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Gauge |
|
|