ZXR10-MPLS-L2VPN

File: ZXR10-MPLS-L2VPN.mib (26800 bytes)

Imported modules

SNMPv2-SMI	SNMPv2-TC	RFC1155-SMI
ZXR10-SMI

Imported symbols

MODULE-IDENTITY	OBJECT-TYPE	Integer32
NOTIFICATION-TYPE	Unsigned32	TEXTUAL-CONVENTION
IpAddress	zxr10L2vpn

Defined Types

DisplayString
OCTET STRING

InterfaceIndex
A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization.
TEXTUAL-CONVENTION
	Integer32	1..2147483647

MplsL2vpnType
Mpls L2vpn type
TEXTUAL-CONVENTION
	INTEGER	l2vpn-UNKNOWN(0), l2vpn-VPWS(1), l2vpn-VPLS(2), l2vpn-IPLS(3)

MplsL2vpnPWType
Mpls L2vpn PW type
TEXTUAL-CONVENTION
	INTEGER	pw-UNKNOWN(0), pw-SPOKE(1), pw-HUB(2)

MplsL2vpnPWEncapsulationType
Mpls L2vpn PW encapsulation type
TEXTUAL-CONVENTION
	INTEGER	encap-UNKNOWN(0), encap-FR-DLCI(1), encap-ATM-AAL5(2), encap-ATM-TRANSCELL(3), encap-ETH-VLAN(4), encap-ETH(5), encap-HDLC(6), encap-PPP(7), encap-CEM(8), encap-ATM-VCC(9), encap-ATM-VPC(10)

MplsL2vpnPWCbit
Mpls L2vpn PW type
TEXTUAL-CONVENTION
	INTEGER	cword-DISABLE(0), cword-ENABLE(1)

MplsL2vpnPWPsnType
Mpls L2vpn PW external label encapsulation type
TEXTUAL-CONVENTION
	INTEGER	unknown-tunnel(0), mpls-tunnel(1), te-tunnel(2)

MplsL2vpnPWStatus
Mpls L2vpn PW status
TEXTUAL-CONVENTION
	INTEGER	not-established(0), established(1)

MplsL2vpnTrapLevel
Mpls L2vpn Trap level.
TEXTUAL-CONVENTION
	INTEGER	emergencies(1), alerts(2), critical(3), errors(4), warnings(5), notifications(6), informational(7), debugging(8)

MplsL2vpnTrapDetail
Mpls L2vpn Trap infromation in detail.
TEXTUAL-CONVENTION
	INTEGER	if-phy-down(1), if-proto-down(2), if-admini-down(3), if-disappear(4), if-encap-chg(5), if-mtu-chg(6), link-no-route(7), link-te-tunnel-down(8), link-no-mpls-tunnel(9), link-no-te-tunnel(10), proto-vc-withdraw(11), proto-sess-down(12), proto-no-vpws(13), proto-no-vpls-peer(14), proto-vctype-negotiate-fail(15), proto-mtu-negotiate-fail(16), proto-cbit-negotiate-fail(17), proto-no-vfi(18)

Zxr10MplsL2vpnInstanceEntry
SEQUENCE
	zxr10MplsL2vpnInstanceType	MplsL2vpnType
	zxr10MplsL2vpnInstanceVCId	Unsigned32
	zxr10MplsL2vpnInstanceVpnName	DisplayString
	zxr10MplsL2vpnPwCounts	Unsigned32

Zxr10MplsL2vpnPWEntry
SEQUENCE
	zxr10MplsL2vpnPWVcId	Unsigned32
	zxr10MplsL2vpnPWType	MplsL2vpnPWType
	zxr10MplsL2vpnPWEncapsulationType	MplsL2vpnPWEncapsulationType
	zxr10MplsL2vpnPWVlanid	Integer32
	zxr10MplsL2vpnPWPsnType	MplsL2vpnPWPsnType
	zxr10MplsL2vpnPWTunnelid	Unsigned32
	zxr10MplsL2vpnPWInlabel	Unsigned32
	zxr10MplsL2vpnPWOutlabel	Unsigned32
	zxr10MplsL2vpnPWCbit	MplsL2vpnPWCbit
	zxr10MplsL2vpnPWStatus	MplsL2vpnPWStatus
	zxr10MplsL2vpnPWLocalGroupId	Unsigned32
	zxr10MplsL2vpnPWLocalEncapsulationType	MplsL2vpnPWEncapsulationType
	zxr10MplsL2vpnPWLocalLabel	Unsigned32
	zxr10MplsL2vpnPWLocalCbit	MplsL2vpnPWCbit
	zxr10MplsL2vpnPWLocalPortName	DisplayString
	zxr10MplsL2vpnPWLocalRouterId	IpAddress
	zxr10MplsL2vpnPWLocalIfMtu	Unsigned32
	zxr10MplsL2vpnPWRemoteGroupId	Unsigned32
	zxr10MplsL2vpnPWRemoteEncapsulationType	MplsL2vpnPWEncapsulationType
	zxr10MplsL2vpnPWRemoteLabel	Unsigned32
	zxr10MplsL2vpnPWRemoteCbit	MplsL2vpnPWCbit
	zxr10MplsL2vpnPWRemotePortName	DisplayString
	zxr10MplsL2vpnPWRemoteRouterId	IpAddress
	zxr10MplsL2vpnPWRemoteIfMtu	Unsigned32

Zxr10MplsL2vpnVpwsIfEntry
SEQUENCE
	zxr10MplsL2vpnVpwsIfIndex	InterfaceIndex
	zxr10MplsL2vpnVpwsIfName	DisplayString
	zxr10MplsL2vpnVpwsIfEncapsulationType	MplsL2vpnPWEncapsulationType
	zxr10MplsL2vpnVpwsIfVcid	Unsigned32
	zxr10MplsL2vpnVpwsIfVpnType	MplsL2vpnType

Defined Values

zxr10MplsL2vpnMIB		1.3.6.1.4.1.3902.3.104.1
ZXROS v4.6.03 Mpls L2vpn query and configuration MIB
MODULE-IDENTITY

zxr10MplsL2vpnObjects		1.3.6.1.4.1.3902.3.104.1.0
OBJECT IDENTIFIER

zxr10MplsL2vpnPWObjects		1.3.6.1.4.1.3902.3.104.1.1
OBJECT IDENTIFIER

zxr10MplsL2vpnVpwsIfObjects		1.3.6.1.4.1.3902.3.104.1.2
OBJECT IDENTIFIER

zxr10MplsL2vpnNotifications		1.3.6.1.4.1.3902.3.104.1.3
OBJECT IDENTIFIER

zxr10MplsL2vpnTrapObjects		1.3.6.1.4.1.3902.3.104.1.4
OBJECT IDENTIFIER

zxr10MplsL2vpnInstanceTable		1.3.6.1.4.1.3902.3.104.1.0.1
Mpls L2vpn instance query table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Zxr10MplsL2vpnInstanceEntry

zxr10MplsL2vpnInstanceEntry		1.3.6.1.4.1.3902.3.104.1.0.1.1
Information of Mpls L2vpn instance configured on a PE
Status: current	Access: not-accessible
OBJECT-TYPE
	Zxr10MplsL2vpnInstanceEntry

zxr10MplsL2vpnInstanceType		1.3.6.1.4.1.3902.3.104.1.0.1.1.1
Mpls L2vpn type,including:vpls,vpws and ipls
Status: current	Access: read-only
OBJECT-TYPE
	MplsL2vpnType

zxr10MplsL2vpnInstanceVCId		1.3.6.1.4.1.3902.3.104.1.0.1.1.2
Mpls L2vpn unique vcid value on a PE.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	1..4294967295

zxr10MplsL2vpnInstanceVpnName		1.3.6.1.4.1.3902.3.104.1.0.1.1.3
Name specified for each configured Mpls L2vpn.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..21)

zxr10MplsL2vpnPwCounts		1.3.6.1.4.1.3902.3.104.1.0.1.1.4
Number of PWs that belongs to a certain Mpls L2vpn
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..32

zxr10MplsL2vpnPWTable		1.3.6.1.4.1.3902.3.104.1.1.1
Mpls L2vpn PW query table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Zxr10MplsL2vpnPWEntry

zxr10MplsL2vpnPWEntry		1.3.6.1.4.1.3902.3.104.1.1.1.1
Informatin of Mpls L2vpn PW configured on a PE.
Status: current	Access: not-accessible
OBJECT-TYPE
	Zxr10MplsL2vpnPWEntry

zxr10MplsL2vpnPWVcId		1.3.6.1.4.1.3902.3.104.1.1.1.1.1
VcId of Mpls L2vpn that PW belongs to.It can't be zero.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	1..4294967295

zxr10MplsL2vpnPWType		1.3.6.1.4.1.3902.3.104.1.1.1.1.2
Type of PW:hub or spoke,used in H-VPLS.
Status: current	Access: read-only
OBJECT-TYPE
	MplsL2vpnPWType

zxr10MplsL2vpnPWEncapsulationType		1.3.6.1.4.1.3902.3.104.1.1.1.1.3
Mpls L2vpn PW encapsulation type.
Status: current	Access: read-only
OBJECT-TYPE
	MplsL2vpnPWEncapsulationType

zxr10MplsL2vpnPWVlanid		1.3.6.1.4.1.3902.3.104.1.1.1.1.4
if zxr10MplsL2vpnPWEncapsulationType is eth-vlan type,this value represents vlan id encapsulated for L2vpn interface.It will be zero otherwise.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

zxr10MplsL2vpnPWPsnType		1.3.6.1.4.1.3902.3.104.1.1.1.1.5
Type of external tunnel for this PW to be carried on.
Status: current	Access: read-only
OBJECT-TYPE
	MplsL2vpnPWPsnType

zxr10MplsL2vpnPWTunnelid		1.3.6.1.4.1.3902.3.104.1.1.1.1.6
If zxr10MplsL2vpnPWPsnType is TE tunnel,this value represents Id of TE tunnel for this PW to be carried on. It will be zero otherwise.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

zxr10MplsL2vpnPWInlabel		1.3.6.1.4.1.3902.3.104.1.1.1.1.7
The PW internal label used in the inbound direction,ie label locally allocated. If the label is not yet known,the object should return a value of 0xFFFFFFFF.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	16..1048575

zxr10MplsL2vpnPWOutlabel		1.3.6.1.4.1.3902.3.104.1.1.1.1.8
The PW internal label used in the outbound direction,ie label allocated by remote peer.If the label is not yet known,the object should return a value of 0xFFFFFFFF.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	16..1048575

zxr10MplsL2vpnPWCbit		1.3.6.1.4.1.3902.3.104.1.1.1.1.9
Defines if the control word will be sent with each packet by the local node.
Status: current	Access: read-only
OBJECT-TYPE
	MplsL2vpnPWCbit

zxr10MplsL2vpnPWStatus		1.3.6.1.4.1.3902.3.104.1.1.1.1.10
If PW has finished negotiation with remote peer including internal label and other parameters,then PW will be in established status.
Status: current	Access: read-only
OBJECT-TYPE
	MplsL2vpnPWStatus

zxr10MplsL2vpnPWLocalGroupId		1.3.6.1.4.1.3902.3.104.1.1.1.1.11
Used in the Group ID field sent to peer within the maintenance protocol used for PW setup.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

zxr10MplsL2vpnPWLocalEncapsulationType		1.3.6.1.4.1.3902.3.104.1.1.1.1.12
Local Mpls L2vpn PW encapsulation type.
Status: current	Access: read-only
OBJECT-TYPE
	MplsL2vpnPWEncapsulationType

zxr10MplsL2vpnPWLocalLabel		1.3.6.1.4.1.3902.3.104.1.1.1.1.13
PW internal label locally allocated.If the label is not yet known, the object should return a value of 0xFFFFFFFF.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	16..1048575

zxr10MplsL2vpnPWLocalCbit		1.3.6.1.4.1.3902.3.104.1.1.1.1.14
Local configuration of the control word.
Status: current	Access: read-only
OBJECT-TYPE
	MplsL2vpnPWCbit

zxr10MplsL2vpnPWLocalPortName		1.3.6.1.4.1.3902.3.104.1.1.1.1.15
Name of local interface that PW has been configured on.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..32)

zxr10MplsL2vpnPWLocalRouterId		1.3.6.1.4.1.3902.3.104.1.1.1.1.16
Router ID of local PE.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

zxr10MplsL2vpnPWLocalIfMtu		1.3.6.1.4.1.3902.3.104.1.1.1.1.17
Locally supported MTU size over the interface associated with the PW.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..65535

zxr10MplsL2vpnPWRemoteGroupId		1.3.6.1.4.1.3902.3.104.1.1.1.1.18
Obtained from the Group ID field as received via the signaling protocol used for PW setup.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

zxr10MplsL2vpnPWRemoteEncapsulationType		1.3.6.1.4.1.3902.3.104.1.1.1.1.19
Remote Mpls L2vpn PW encapsulation type.
Status: current	Access: read-only
OBJECT-TYPE
	MplsL2vpnPWEncapsulationType

zxr10MplsL2vpnPWRemoteLabel		1.3.6.1.4.1.3902.3.104.1.1.1.1.20
PW internal label allocated by remote peer.If the label is not yet known, the object should return a value of 0xFFFFFFFF.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

zxr10MplsL2vpnPWRemoteCbit		1.3.6.1.4.1.3902.3.104.1.1.1.1.21
Remote configuration of the control word.
Status: current	Access: read-only
OBJECT-TYPE
	MplsL2vpnPWCbit

zxr10MplsL2vpnPWRemotePortName		1.3.6.1.4.1.3902.3.104.1.1.1.1.22
Name of remote interface that PW has been configured on.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..32)

zxr10MplsL2vpnPWRemoteRouterId		1.3.6.1.4.1.3902.3.104.1.1.1.1.23
Router ID of remote PE.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

zxr10MplsL2vpnPWRemoteIfMtu		1.3.6.1.4.1.3902.3.104.1.1.1.1.24
Supported MTU size of remote peer over the interface associated with the PW.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

zxr10MplsL2vpnVpwsIfTable		1.3.6.1.4.1.3902.3.104.1.2.1
Mpls L2vpn instance query table
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Zxr10MplsL2vpnVpwsIfEntry

zxr10MplsL2vpnVpwsIfEntry		1.3.6.1.4.1.3902.3.104.1.2.1.1
Information of Mpls L2vpn instance configured on a PE
Status: current	Access: not-accessible
OBJECT-TYPE
	Zxr10MplsL2vpnVpwsIfEntry

zxr10MplsL2vpnVpwsIfIndex		1.3.6.1.4.1.3902.3.104.1.2.1.1.1
Index of the VPWS configuration interface.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

zxr10MplsL2vpnVpwsIfName		1.3.6.1.4.1.3902.3.104.1.2.1.1.2
Name of the VPWS configuration interface.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..32)

zxr10MplsL2vpnVpwsIfEncapsulationType		1.3.6.1.4.1.3902.3.104.1.2.1.1.3
Encapsulation type of the VPWS configuration interface.
Status: current	Access: read-only
OBJECT-TYPE
	MplsL2vpnPWEncapsulationType

zxr10MplsL2vpnVpwsIfVcid		1.3.6.1.4.1.3902.3.104.1.2.1.1.4
Vcid of the VPWS configured on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	1..4294967295

zxr10MplsL2vpnVpwsIfVpnType		1.3.6.1.4.1.3902.3.104.1.2.1.1.5
Type of the L2VPN configured on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	MplsL2vpnType

zxr10MplsL2vpnTrapIfIndex		1.3.6.1.4.1.3902.3.104.1.4.1
If a L2vpn configuration interface is down,a interface down trap pdu will be sent;zxr10MplsL2vpnTrapIfIndex is index of this interface in if table.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

zxr10MplsL2vpnTrapIfName		1.3.6.1.4.1.3902.3.104.1.4.2
If a L2vpn configuration interface is down,a interface down trap will be sent;zxr10MplsL2vpnTrapIfName is name of this interface.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..32)

zxr10MplsL2vpnTrapLevel		1.3.6.1.4.1.3902.3.104.1.4.3
Alerting level of Trap pdu.
Status: current	Access: read-only
OBJECT-TYPE
	MplsL2vpnTrapLevel

zxr10MplsL2vpnTrapDetail		1.3.6.1.4.1.3902.3.104.1.4.4
Detailed information of Trap arising.
Status: current	Access: read-only
OBJECT-TYPE
	MplsL2vpnTrapDetail

zxr10MplsL2vpnTrapVcid		1.3.6.1.4.1.3902.3.104.1.4.5
Vcid of L2vpn affected.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	1..4294967295

zxr10MplsL2vpnTrapPeerAddress		1.3.6.1.4.1.3902.3.104.1.4.6
Peer Address of VC affected.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

zxr10MplsL2vpnTrapVpnType		1.3.6.1.4.1.3902.3.104.1.4.7
Peer Address of VC affected.
Status: current	Access: read-only
OBJECT-TYPE
	MplsL2vpnType

zxr10MplsL2vpnTrapTETunnelId		1.3.6.1.4.1.3902.3.104.1.4.8
TE Tunnel Id which VC has been bound to.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	1..4294967295

mplsL2vpnGenericInterfaceTrap		1.3.6.1.4.1.3902.3.104.1.3.1
When one of following conditions happens: (1)Admini,phy or protocol status of a interface is down and it has no children. (2)Interface is off and it has no children. (3)Encapsulation of a interface has changed. (4)MTU of a interface has changed. this type of Trap pdu will be sent.There is only one VPWS type VC affected.
Status: current	Access: read-only
NOTIFICATION-TYPE

mplsL2vpnMatchInterfaceTrap		1.3.6.1.4.1.3902.3.104.1.3.2
When one of following conditions happens: (1)Admini,phy or protocol status of a interface is down and it has children. (2)Interface is off and it has children. this type of Trap pdu will be sent.
Status: current	Access: read-only
NOTIFICATION-TYPE

mplsL2vpnGenericProtocolTrap		1.3.6.1.4.1.3902.3.104.1.3.3
When one of following conditions happens: (1)Receives a VC label withdraw message from remote peer. (2)Deletes a VPWS VC. (3)Delete a VPLS peer. (4)Protocol patameters negotiation fails during VC setup. this type of Trap pdu will be sent.
Status: current	Access: read-only
NOTIFICATION-TYPE

mplsL2vpnSessionDownTrap		1.3.6.1.4.1.3902.3.104.1.3.4
When session to VC peer is down,all the VC that have been bound to mpls Lsp Tunnel will be down;this kind of trap will be sent.
Status: current	Access: read-only
NOTIFICATION-TYPE

mplsL2vpnVplsDeleteTrap		1.3.6.1.4.1.3902.3.104.1.3.5
When delete a VPLS instance.,this kind of trap will be sent.
Status: current	Access: read-only
NOTIFICATION-TYPE

mplsL2vpnLinkTrap		1.3.6.1.4.1.3902.3.104.1.3.6
When one of following conditions happens: (1)The PSN route is off. (2)Can't find outer mpls tunnel label. (3)Can't find outer TE tunnel label. this type of Trap pdu will be sent.
Status: current	Access: read-only
NOTIFICATION-TYPE

mplsL2vpnPsnRouteDownTrap		1.3.6.1.4.1.3902.3.104.1.3.7
When PSN route between PE is down,all the VC between them will be down; this type of Trap pdu will be sent.
Status: current	Access: read-only
NOTIFICATION-TYPE

mplsL2vpnTETunnelDownTrap		1.3.6.1.4.1.3902.3.104.1.3.8
When one TE Tunnel between is dwon,all the VC between them which has been bound to this tunnel will be down;this type of Trap pdu will be sent
Status: current	Access: read-only
NOTIFICATION-TYPE