ZXR10-L2VPN-MIB

Imported modules

Imported symbols

OBJECT-TYPE	MODULE-IDENTITY	Integer32
Counter32	Unsigned32	enterprises
IpAddress	DisplayString	TEXTUAL-CONVENTION

Defined Types

L2vpnPWType
L2vpn PW Type. Assigned values are specified in 'IANA Allocations for Pseudowire Edge to Edge Emulation (PWE3)
TEXTUAL-CONVENTION
	INTEGER	unknown(0), fr-dlci-martini(1), aal5-sdu(2), atm-cell(3), vlan(4), ethernet(5), hdlc(6), ppp(7), sdh-cesom(8), atm-vccn(9), atm-vpcn(10), ip(11), atm-vcc1(12), atm-vpc1(13), aal5-pdu(14), fr-port(15), sdh-ceop(16), e1(17), t1-ds1(18), e3(19), t3-ds3(20), cesopsn(21), tdm-aal1(22), tdm-with-cas(23), tdm-aal2(24), fr-dlct(25)

L2vpnVplsPolicy
L2vpn Vpls Policy.
TEXTUAL-CONVENTION
	INTEGER	tunnelling(1), discarding(2), terminating(3), tunnellingMonitor(4)

Zxr10L2vpnSduEntry
SEQUENCE
	zxr10L2vpnSduServiceName	DisplayString
	zxr10L2vpnSduName	DisplayString
	zxr10L2vpnSduServiceType	INTEGER
	zxr10L2vpnSduRedandancyMgrName	DisplayString
	zxr10L2vpnSduRedundancyPrimaryPwPeer	IpAddress
	zxr10L2vpnSduRedundancyPrimaryPwVcid	Unsigned32
	zxr10L2vpnSduRedundancyPrimaryPwVcType	L2vpnPWType
	zxr10L2vpnSduRedundancyBackupPwPeer	IpAddress
	zxr10L2vpnSduRedundancyBackupPwVcid	Unsigned32
	zxr10L2vpnSduRedundancyBackupPwVcType	L2vpnPWType

Zxr10L2vpnSacEntry
SEQUENCE
	zxr10L2vpnSacServiceName	DisplayString
	zxr10L2vpnSacName	DisplayString
	zxr10L2vpnSacServiceType	INTEGER
	zxr10L2vpnSacServiceDefine	INTEGER
	zxr10L2vpnSacEthSwitchSplitHorizone	INTEGER
	zxr10L2vpnSacEthIngressAdjustType	INTEGER
	zxr10L2vpnSacEthPushedTag	Integer32
	zxr10L2vpnSacEthRewriteTargetTag	Integer32
	zxr10L2vpnSacTdmJitterBuffer	Integer32
	zxr10L2vpnSacTdmDistributePeriod	Integer32
	zxr10L2vpnSacTdmTimeslots	Unsigned32
	zxr10L2vpnSacTdmStructureType	INTEGER
	zxr10L2vpnSacEthSwitchGroupID	Integer32
	zxr10L2vpnSacInterworking	INTEGER
	zxr10L2vpnSacInterworkingIpLocalCeMac	DisplayString

Zxr10L2vpnRedundancyEntry
SEQUENCE
	zxr10L2vpnRedundancyName	DisplayString
	zxr10L2vpnRedundancySduName	DisplayString
	zxr10L2vpnRedundancyProtectMode	INTEGER
	zxr10L2vpnRedundancyPfsNegoMode	INTEGER
	zxr10L2vpnRedundancyProtectPolicy	INTEGER
	zxr10L2vpnRedundancyProtectDelayTime	Integer32
	zxr10L2vpnRedundancyRevertPolicy	INTEGER
	zxr10L2vpnRedundancyRevertDelayTime	Integer32
	zxr10L2vpnRedundancyActivePWs	INTEGER
	zxr10L2vpnRedundancyStandbyPWs	INTEGER
	zxr10L2vpnRedundancyInvalidPWs	INTEGER
	zxr10L2vpnRedundancyProtectionCount	Counter32
	zxr10L2vpnRedundancyLastProtectionTime	Unsigned32

Zxr10L2vpnPwEntry
SEQUENCE
	zxr10L2vpnPwPeer	IpAddress
	zxr10L2vpnPwVcid	Unsigned32
	zxr10L2vpnPwVcType	L2vpnPWType
	zxr10L2vpnPwSduName	DisplayString
	zxr10L2vpnPwServiceName	DisplayString
	zxr10L2vpnPwServiceType	INTEGER
	zxr10L2vpnPwIsMspwSegment	INTEGER
	zxr10L2vpnPwLocalLabel	Integer32
	zxr10L2vpnPwRemoteLabel	Integer32
	zxr10L2vpnPwSignalType	INTEGER
	zxr10L2vpnPwLocalGroupId	Integer32
	zxr10L2vpnPwLocalCbit	INTEGER
	zxr10L2vpnPwLocalMTU	Integer32
	zxr10L2vpnPwLocalDescription	DisplayString
	zxr10L2vpnPwLocalStatusWord	Unsigned32
	zxr10L2vpnPwLocalStatusSignalAbility	INTEGER
	zxr10L2vpnPwRemoteGroupId	Integer32
	zxr10L2vpnPwRemoteCbit	INTEGER
	zxr10L2vpnPwRemoteMTU	Integer32
	zxr10L2vpnPwRemoteDescription	DisplayString
	zxr10L2vpnPwRemoteStatusWord	Unsigned32
	zxr10L2vpnPwRemoteStatusSignalAbility	INTEGER
	zxr10L2vpnPwNegoedCbit	INTEGER
	zxr10L2vpnPwNegoedMTU	Integer32
	zxr10L2vpnPwNegoedStatusSignalAbility	INTEGER
	zxr10L2vpnPwSignalState	INTEGER
	zxr10L2vpnPwVccvLocalParas	Unsigned32
	zxr10L2vpnPwVccvRemoteParas	Unsigned32
	zxr10L2vpnPwVccvNegoedParas	Unsigned32
	zxr10L2vpnPwPsnOutLabelDepth	Integer32
	zxr10L2vpnPwPsnOutLabel1	Integer32
	zxr10L2vpnPwPsnOutLabel2	Integer32
	zxr10L2vpnPwPsnOutLabel3	Integer32
	zxr10L2vpnPwPsnTunnelType	INTEGER
	zxr10L2vpnPwPsnTunnelId	Integer32
	zxr10L2vpnPwSwitchMacWithdraw	INTEGER
	zxr10L2vpnPwServiceState	INTEGER
	zxr10L2vpnPwWorkState	INTEGER
	zxr10L2vpnPwSwitchSplitHorizone	INTEGER
	zxr10L3vpnPwSwitchGroupID	Integer32

Zxr10L2vpnServiceEntry
SEQUENCE
	zxr10L2vpnServiceName	DisplayString
	zxr10L2vpnServiceType	INTEGER
	zxr10L2vpnServiceSac1Name	DisplayString
	zxr10L2vpnServiceSac2Name	DisplayString
	zxr10L2vpnServiceSdu1Name	DisplayString
	zxr10L2vpnServiceSdu2Name	DisplayString
	zxr10L2vpnServiceMTU	Integer32
	zxr10L2vpnServiceMspwFirstPwPeer	IpAddress
	zxr10L2vpnServiceMspwFirstPwVcid	Unsigned32
	zxr10L2vpnServiceMspwFirstPWVcType	L2vpnPWType
	zxr10L2vpnServiceMspwSecondPwPeer	IpAddress
	zxr10L2vpnServiceMspwSecondPwVcid	Unsigned32
	zxr10L2vpnServiceMspwSecondPwVcType	L2vpnPWType

Zxr10L2vpnVplsEntry
SEQUENCE
	zxr10L2vpnVplsName	DisplayString
	zxr10L2vpnVplsApplication	INTEGER
	zxr10L2vpnVplsModelType	INTEGER
	zxr10L2vpnVplsServiceMTU	Integer32
	zxr10L2vpnVplsSwitchMacLearning	INTEGER
	zxr10L2vpnVplsSwitchMacAging	INTEGER
	zxr10L2vpnVplsSwitchStatistics	INTEGER
	zxr10L2vpnVplsSwitchMacWithdraw	INTEGER
	zxr10L2vpnVplsTimerMacAging	Integer32
	zxr10L2vpnVplsAntimovePolicy	INTEGER
	zxr10L2vpnVplsL2ptPolicyLACP	L2vpnVplsPolicy
	zxr10L2vpnVplsL2ptPolicyDot1X	L2vpnVplsPolicy
	zxr10L2vpnVplsL2ptPolicyGARP	L2vpnVplsPolicy
	zxr10L2vpnVplsL2ptPolicySTP	L2vpnVplsPolicy
	zxr10L2vpnVplsL2ptPolicyLLDP	L2vpnVplsPolicy
	zxr10L2vpnVplsL2ptPolicyDot3X	L2vpnVplsPolicy
	zxr10L2vpnVplsL2ptPolicyALL	L2vpnVplsPolicy
	zxr10L2vpnVplsL2ptPolicyAllBridgeMulticast	L2vpnVplsPolicy
	zxr10L2vpnVplsL2ptPolicyZDPZTP	L2vpnVplsPolicy

Defined Values

zte		1.3.6.1.4.1.3902
This MIB contains managed object definitions for the ZXROSng L2vpn
MODULE-IDENTITY

zxr10		1.3.6.1.4.1.3902.3
OBJECT IDENTIFIER

zxr10l2vpn		1.3.6.1.4.1.3902.3.104
OBJECT IDENTIFIER

zxr10l2vpnObjects		1.3.6.1.4.1.3902.3.104.10
OBJECT IDENTIFIER

zxr10l2vpnGlobalPara		1.3.6.1.4.1.3902.3.104.10.10
OBJECT IDENTIFIER

zxr10L2vpnGlobalPWCapatity		1.3.6.1.4.1.3902.3.104.10.10.1
The summary information about max_num of PWs'configuration.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

zxr10L2vpnGlobalPWUsed		1.3.6.1.4.1.3902.3.104.10.10.2
The summary information about current_num of PWs'configuration.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

zxr10L2vpnEnable		1.3.6.1.4.1.3902.3.104.10.20
Enable L2VPN service.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

zxr10L2vpnSduTable		1.3.6.1.4.1.3902.3.104.10.1
Sdu Table. This table contains one entry per sdu table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Zxr10L2vpnSduEntry

zxr10L2vpnSduEntry		1.3.6.1.4.1.3902.3.104.10.1.1
The parameter of a Sdu entity containing
Status: current	Access: not-accessible
OBJECT-TYPE
	Zxr10L2vpnSduEntry

zxr10L2vpnSduServiceName		1.3.6.1.4.1.3902.3.104.10.1.1.1
The name of the service instance.It consists of 'Forwarder' modules connected by pseudowires and Attach Circuit.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

zxr10L2vpnSduName		1.3.6.1.4.1.3902.3.104.10.1.1.2
The name of Service Distribution Unit (SDU).
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

zxr10L2vpnSduServiceType		1.3.6.1.4.1.3902.3.104.10.1.1.3
The type of service instance.There are several types of L2VPNs:(1)Virtual Private LAN Service(VPLS), and (2)Ethernet over PW,and (3)Multi-segment Pseudowire(MSPW), and (4)Enhanced-Ethernet over Pseudowire
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(0), vpls(1), vpws(2), mspw(3), enhanced-vpws(6)

zxr10L2vpnSduRedandancyMgrName		1.3.6.1.4.1.3902.3.104.10.1.1.4
The name of Redundency-manager.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

zxr10L2vpnSduRedundancyPrimaryPwPeer		1.3.6.1.4.1.3902.3.104.10.1.1.5
The PW's remote endpoint address.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

zxr10L2vpnSduRedundancyPrimaryPwVcid		1.3.6.1.4.1.3902.3.104.10.1.1.6
A non-zero 32-bit connection ID that, together with the PW type, identifies a particular PW. Note that the PW ID and the PW type MUST be the same at both endpoints.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

zxr10L2vpnSduRedundancyPrimaryPwVcType		1.3.6.1.4.1.3902.3.104.10.1.1.7
A 15-bit quantity containing a value that represents the type of PW. Assigned values are specified in 'IANA Allocations for Pseudowire Edge to Edge Emulation (PWE3)'.
Status: current	Access: read-only
OBJECT-TYPE
	L2vpnPWType

zxr10L2vpnSduRedundancyBackupPwPeer		1.3.6.1.4.1.3902.3.104.10.1.1.8
The PW's remote endpoint address.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

zxr10L2vpnSduRedundancyBackupPwVcid		1.3.6.1.4.1.3902.3.104.10.1.1.9
A non-zero 32-bit connection ID that, together with the PW type, identifies a particular PW. Note that the PW ID and the PW type MUST be the same at both endpoints.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

zxr10L2vpnSduRedundancyBackupPwVcType		1.3.6.1.4.1.3902.3.104.10.1.1.10
A 15-bit quantity containing a value that represents the type of PW. Assigned values are specified in 'IANA Allocations for Pseudowire Edge to Edge Emulation (PWE3)'.
Status: current	Access: read-only
OBJECT-TYPE
	L2vpnPWType

zxr10L2vpnSacTable		1.3.6.1.4.1.3902.3.104.10.2
Sac Table. This table contains one entry per Sac table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Zxr10L2vpnSacEntry

zxr10L2vpnSacEntry		1.3.6.1.4.1.3902.3.104.10.2.1
The parameter of a Sac entity containing
Status: current	Access: not-accessible
OBJECT-TYPE
	Zxr10L2vpnSacEntry

zxr10L2vpnSacServiceName		1.3.6.1.4.1.3902.3.104.10.2.1.1
The name of the service instance.It consists of 'Forwarder' modules connected by pseudowires and Attach Circuit.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

zxr10L2vpnSacName		1.3.6.1.4.1.3902.3.104.10.2.1.2
The name of Service Attachment Circuit(SAC).
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

zxr10L2vpnSacServiceType		1.3.6.1.4.1.3902.3.104.10.2.1.3
The type of service instance.There are several types of L2VPNs:(1)Virtual Private LAN Service(VPLS), and (2)Virtual Private Wire Service(VPWS),and (3)Virtual Local Switching Service(VLSS),and (4)Enhanced-Virtual Private Wire Service(Enhanced-VPWS) ;
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(0), vpls(1), vpws(2), vlss(4), enhanced-vpws(6)

zxr10L2vpnSacServiceDefine		1.3.6.1.4.1.3902.3.104.10.2.1.4
The parameter of service accesse.There are several parameters of service accesse:(1)ethernt,(2)tdm, (3)ppp,(4)hdlc,(5)fr.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ethernt(1), tdm(2), ppp(3), hdlc(4), fr(5)

zxr10L2vpnSacEthSwitchSplitHorizone		1.3.6.1.4.1.3902.3.104.10.2.1.5
Split-horizon attribute which used in E-tree service includes two types client/server
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	null(0), on(1), off(2)

zxr10L2vpnSacEthIngressAdjustType		1.3.6.1.4.1.3902.3.104.10.2.1.20
The Type of VLAN tag ingress-adjustment.It consists of (1)needless,(2)push,(3)pop-outermost,(4)rewrite
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(0), needless(1), push(2), pop-outermost(3), rewrite(4)

zxr10L2vpnSacEthPushedTag		1.3.6.1.4.1.3902.3.104.10.2.1.21
A service-delimiting tag which pushed onto the incoming packets.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..4094

zxr10L2vpnSacEthRewriteTargetTag		1.3.6.1.4.1.3902.3.104.10.2.1.22
A VLAN tag which rewirted to replace the service-delimiting tags.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..4094

zxr10L2vpnSacTdmJitterBuffer		1.3.6.1.4.1.3902.3.104.10.2.1.23
The jitter-buffer size of TDM emulation.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	2..64

zxr10L2vpnSacTdmDistributePeriod		1.3.6.1.4.1.3902.3.104.10.2.1.24
Tthe period of distributing TDM packets to remote end-point.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..64

zxr10L2vpnSacTdmTimeslots		1.3.6.1.4.1.3902.3.104.10.2.1.25
The time of TDM slots.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

zxr10L2vpnSacTdmStructureType		1.3.6.1.4.1.3902.3.104.10.2.1.26
The structure type of TDM emulation.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	aware(1), agnostic(2), aware-with-cas(3)

zxr10L2vpnSacEthSwitchGroupID		1.3.6.1.4.1.3902.3.104.10.2.1.27
Split-horizon-Group attribute.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..64

zxr10L2vpnSacInterworking		1.3.6.1.4.1.3902.3.104.10.2.1.28
The name of SacInterworking.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(0), ip(1), ethernet(2)

zxr10L2vpnSacInterworkingIpLocalCeMac		1.3.6.1.4.1.3902.3.104.10.2.1.29
The LocalCeMac of SacInterworking.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

zxr10L2vpnRedundancyTable		1.3.6.1.4.1.3902.3.104.10.3
Redundancy Table. This table contains one entry per Redundancy table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Zxr10L2vpnRedundancyEntry

zxr10L2vpnRedundancyEntry		1.3.6.1.4.1.3902.3.104.10.3.1
The parameter of a Redundancy entity containing
Status: current	Access: not-accessible
OBJECT-TYPE
	Zxr10L2vpnRedundancyEntry

zxr10L2vpnRedundancyName		1.3.6.1.4.1.3902.3.104.10.3.1.1
The name of redundency-management.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

zxr10L2vpnRedundancySduName		1.3.6.1.4.1.3902.3.104.10.3.1.2
The name of Service Distribution Unit (SDU) belongs to the exact redundency-management instance.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

zxr10L2vpnRedundancyProtectMode		1.3.6.1.4.1.3902.3.104.10.3.1.3
The protectmode of redundency-management instance. There are two modes: (1)oneByOne, (2)onePlusOne
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	oneByOne(1), onePlusOne(2)

zxr10L2vpnRedundancyPfsNegoMode		1.3.6.1.4.1.3902.3.104.10.3.1.4
Configure the negotiation mode which include four modes :(1) unsupported, (2)independent, (3)master, (4)slave.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unsupported(1), independent(2), master(3), slave(4)

zxr10L2vpnRedundancyProtectPolicy		1.3.6.1.4.1.3902.3.104.10.3.1.5
The protect-policy of transforming primary-pw into backup-pw.There are two policies:(1)immediately, (2)delayed.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	immediately(1), delayed(2)

zxr10L2vpnRedundancyProtectDelayTime		1.3.6.1.4.1.3902.3.104.10.3.1.6
The time of transforming primary-pw into backup-pw.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	10..180

zxr10L2vpnRedundancyRevertPolicy		1.3.6.1.4.1.3902.3.104.10.3.1.7
The protectpolicy of transforming primary-pw from backup-pw. There are two policies:(1)immediately, (2)delayed.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	immediately(1), delayed(2), never(3)

zxr10L2vpnRedundancyRevertDelayTime		1.3.6.1.4.1.3902.3.104.10.3.1.8
The time of transforming primary-pw from backup-pw.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	10..180

zxr10L2vpnRedundancyActivePWs		1.3.6.1.4.1.3902.3.104.10.3.1.9
The statues of current active-pws.There are three statues:(1)primary,(2)backup,(3)none.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	primary(1), backup(2), none(3)

zxr10L2vpnRedundancyStandbyPWs		1.3.6.1.4.1.3902.3.104.10.3.1.10
The statues of current standby-pws.There are three statues:(1)primary,(2)backup,(3)none.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	primary(1), backup(2), none(3)

zxr10L2vpnRedundancyInvalidPWs		1.3.6.1.4.1.3902.3.104.10.3.1.11
The statues of current invalid-pws.There are three statues:(1)primary,(2)backup,(3)none.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	primary(1), backup(2), none(3)

zxr10L2vpnRedundancyProtectionCount		1.3.6.1.4.1.3902.3.104.10.3.1.12
The total number of the pws switchover. Transforming primary-pw into backup-pw or transforming primary-pw from backup-pw means one.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

zxr10L2vpnRedundancyLastProtectionTime		1.3.6.1.4.1.3902.3.104.10.3.1.13
The time of the last switchover, which ransform primary-pw into backup-pw or transform primary-pw from backup-pw.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

zxr10L2vpnPwTable		1.3.6.1.4.1.3902.3.104.10.4
Pw Table. This table contains one entry per pw table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Zxr10L2vpnPwEntry

zxr10L2vpnPwEntry		1.3.6.1.4.1.3902.3.104.10.4.1
The parameter of a pw entity containing statistics information about a particular PW.
Status: current	Access: not-accessible
OBJECT-TYPE
	Zxr10L2vpnPwEntry

zxr10L2vpnPwPeer		1.3.6.1.4.1.3902.3.104.10.4.1.1
The PW's remote endpoint address.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

zxr10L2vpnPwVcid		1.3.6.1.4.1.3902.3.104.10.4.1.2
A non-zero 32-bit connection ID that, together with the PW type, identifies a particular PW. Note that the PW ID and the PW type MUST be the same at both endpoints.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

zxr10L2vpnPwVcType		1.3.6.1.4.1.3902.3.104.10.4.1.3
A 15-bit quantity containing a value that represents the type of PW. Assigned values are specified in 'IANA Allocations for Pseudowire Edge to Edge Emulation (PWE3)'.
Status: current	Access: read-only
OBJECT-TYPE
	L2vpnPWType

zxr10L2vpnPwSduName		1.3.6.1.4.1.3902.3.104.10.4.1.4
The name of Service Distribution Unit (SDU).
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

zxr10L2vpnPwServiceName		1.3.6.1.4.1.3902.3.104.10.4.1.5
The name of the service instance.It consists of 'Forwarder' modules connected by pseudowires and Attach Circuit.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

zxr10L2vpnPwServiceType		1.3.6.1.4.1.3902.3.104.10.4.1.6
The type of service instance.There are several types of L2VPNs:(1)Virtual Private LAN Service(VPLS), and (2)Ethernet over PW,and (3)Multi-segment Pseudowire(MSPW), and (4)Virtual Local Switching Service(VLSS),and (5)Enhanced-Ethernet over Pseudowire
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(0), vpls(1), vpws(2), mspw(3), vlss(4), enhanced-vpws(6)

zxr10L2vpnPwIsMspwSegment		1.3.6.1.4.1.3902.3.104.10.4.1.7
The MSPW's ability weather the PW is MSPW's member.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	first(1), second(2), none(3)

zxr10L2vpnPwLocalLabel		1.3.6.1.4.1.3902.3.104.10.4.1.8
The PW's local label.When egress LER receives a packet over a pseudowire,the PW's local label must be able to determine that the packet was in fact received over a pseudowire associate with a particular pseudowire, and disposites the packet.In an MPLS-enabled IP network, a PW local label is an MPLS label used to identify packet with a PW that belongs to a particular Virtual Private Network.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	16..1048575

zxr10L2vpnPwRemoteLabel		1.3.6.1.4.1.3902.3.104.10.4.1.9
The PW's remote label.When ingress LER sends a Layer 2 PDU to remote egress LER,it creates an MPLS packets by adding the PW's remote label to the packet,thus creating the first entry of the label stack.The PW's remote label is not visible again until the MPLS packet reaches the egress LER.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	16..1048575

zxr10L2vpnPwSignalType		1.3.6.1.4.1.3902.3.104.10.4.1.10
The type of signaling,including (1)static PW,and (2) the Pwid FEC Element(FEC type 128),and the Generlized Pwid FEC Element(FEC type 129).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	static(1), fec128(2), fec129(3)

zxr10L2vpnPwLocalGroupId		1.3.6.1.4.1.3902.3.104.10.4.1.11
The PW's local GroupId value.It is an arbitrary 32-bit value that represents a group of PWs that is used to create groups in the PW space.The group ID is intended to be used as a port index, or a virtual tunnel index.To simplify configuration, a particular PW ID at ingress could be part of the virtual tunnel for transport to the egress router The Group ID is very useful for sending wild card label withdrawals, or PW wild card status notification messages to remote PEs upon physical port failure.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..65535

zxr10L2vpnPwLocalCbit		1.3.6.1.4.1.3902.3.104.10.4.1.12
The PW's local ability weather it is supporting CBit. The bit (C) is used to flag the presence of a control word as follows:C = 1 Control word present on this PW. C = 0 No control word present on this PW.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

zxr10L2vpnPwLocalMTU		1.3.6.1.4.1.3902.3.104.10.4.1.13
The PW's local MTU value.This is the Maximum Transmission Unit, excluding encapsulation overhead, of the egresspacket interface that will be transmitting the decapsulated PDUthat is received from the MPLS-enabled network. This parameter is applicable only to PWs transporting packets and is REQUIRED for these PW types. If this parameter does not match in both directions of a specific PW, that PW MUST NOT be enabled.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..65535

zxr10L2vpnPwLocalDescription		1.3.6.1.4.1.3902.3.104.10.4.1.14
The PW's local descripton. This arbitrary, and OPTIONAL, interface description string is used to send a human-readable administrative string describing the interface to the remote. This parameter is OPTIONAL and is applicable to all PW types. The interface description parameter string length is variable and can be from 0 to 80 octets. Human-readable text MUST be provided in the UTF-8 charset using the Default Language.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

zxr10L2vpnPwLocalStatusWord		1.3.6.1.4.1.3902.3.104.10.4.1.15
The PW's local status value. Each bit in the status code field can be used to indicate a single failure or an event. When a PW is first set up, the PEs MUST attempt to negotiate the usage of the PW status TLV.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

zxr10L2vpnPwLocalStatusSignalAbility		1.3.6.1.4.1.3902.3.104.10.4.1.16
The PW's local status signal ability. Osbits represents support pw operational status notification, PFSbit represents support preferred forwarding status notification, RSSbit represents support requested switchover status notification, None represents do not support any pw status notification.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	osbits(1), pfsbit(2), rssbit(3), none(4)

zxr10L2vpnPwRemoteGroupId		1.3.6.1.4.1.3902.3.104.10.4.1.17
The PW's remote GroupId value.It is an arbitrary 32-bit value that represents a group of PWs that is used to create groups in the PW space.The group ID is intended to be used as a port index, or a virtual tunnel index.To simplify configuration, a particular PW ID at ingress could be part of the virtual tunnel for transport to the egress router The Group ID is very useful for sending wild card label withdrawals, or PW wild card status notification messages to remote PEs upon physical port failure.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..65535

zxr10L2vpnPwRemoteCbit		1.3.6.1.4.1.3902.3.104.10.4.1.18
The PW's remote ability weather it is supporting CBit. The bit (C) is used to flag the presence of a control word as follows:C = 1 Control word present on this PW. C = 0 No control word present on this PW.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

zxr10L2vpnPwRemoteMTU		1.3.6.1.4.1.3902.3.104.10.4.1.19
The PW's remote MTU value.This is the Maximum Transmission Unit, excluding encapsulation overhead, of the egresspacket interface that will be transmitting the decapsulated PDUthat is received from the MPLS-enabled network. This parameter is applicable only to PWs transporting packets and is REQUIRED for these PW types. If this parameter does not match in both directions of a specific PW, that PW MUST NOT be enabled.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..65535

zxr10L2vpnPwRemoteDescription		1.3.6.1.4.1.3902.3.104.10.4.1.20
The PW's remote descripton. This arbitrary, and OPTIONAL, interface description string is used to send a human-readable administrative string describing the interface to the remote. This parameter is OPTIONAL and is applicable to all PW types. The interface description parameter string length is variable and can be from 0 to 80 octets. Human-readable text MUST be provided in the UTF-8 charset using the Default Language.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

zxr10L2vpnPwRemoteStatusWord		1.3.6.1.4.1.3902.3.104.10.4.1.21
The PW's remote status value. Each bit in the status code field can be used to indicate a single failure or an event. When a PW is first set up, the PEs MUST attempt to negotiate the usage of the PW status TLV.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

zxr10L2vpnPwRemoteStatusSignalAbility		1.3.6.1.4.1.3902.3.104.10.4.1.22
The PW's remote status signal ability. Osbits represents support pw operational status notification, PFSbit represents support preferred forwarding status notification, RSSbit represents support requested switchover status notification, None represents do not support any pw status notification.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	osbits(1), pfsbit(2), rssbit(3), none(4)

zxr10L2vpnPwNegoedCbit		1.3.6.1.4.1.3902.3.104.10.4.1.23
The PW's negotiated ability weather it is supporting CBit. The bit (C) is used to flag the presence of a control word as follows:C = 1 Control word present on this PW. C = 0 No control word present on this PW.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

zxr10L2vpnPwNegoedMTU		1.3.6.1.4.1.3902.3.104.10.4.1.24
The PW's negotiated MTU value.This is the Maximum Transmission Unit, excluding encapsulation overhead, of the egresspacket interface that will be transmitting the decapsulated PDUthat is received from the MPLS-enabled network. This parameter is applicable only to PWs transporting packets and is REQUIRED for these PW types. If this parameter does not match in both directions of a specific PW, that PW MUST NOT be enabled.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..65535

zxr10L2vpnPwNegoedStatusSignalAbility		1.3.6.1.4.1.3902.3.104.10.4.1.25
The PW's negotiated status signal ability. Osbits represents support pw operational status notification, PFSbit represents support preferred forwarding status notification, RSSbit represents support requested switchover status notification, None represents do not support any pw status notification.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	osbits(1), pfsbit(2), rssbit(3), none(4)

zxr10L2vpnPwSignalState		1.3.6.1.4.1.3902.3.104.10.4.1.26
The PW's signal state on protocol level.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	down(0), up(1)

zxr10L2vpnPwVccvLocalParas		1.3.6.1.4.1.3902.3.104.10.4.1.27
The PW's local VCCV value. This VCCV capability information indicates to the receiving PE which combinations of Control Channel (CC) andConnectivity Verification (CV) Types it is capable of receiving. Ifthe receiving PE agrees to establish the PW, it will return its capabilities in the subsequent signaling message to indicate which CC and CV Types it is capable of processing.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

zxr10L2vpnPwVccvRemoteParas		1.3.6.1.4.1.3902.3.104.10.4.1.28
The PW's remote VCCV value. This VCCV capability information indicates to the receiving PE which combinations of Control Channel (CC) andConnectivity Verification (CV) Types it is capable of receiving. Ifthe receiving PE agrees to establish the PW, it will return its capabilities in the subsequent signaling message to indicate which CC and CV Types it is capable of processing.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

zxr10L2vpnPwVccvNegoedParas		1.3.6.1.4.1.3902.3.104.10.4.1.29
The PW's negotiated VCCV value. This VCCV capability information indicates to the receiving PE which combinations of Control Channel (CC) andConnectivity Verification (CV) Types it is capable of receiving. Ifthe receiving PE agrees to establish the PW, it will return its capabilities in the subsequent signaling message to indicate which CC and CV Types it is capable of processing.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

zxr10L2vpnPwPsnOutLabelDepth		1.3.6.1.4.1.3902.3.104.10.4.1.30
The layer of MPLS label in the packet when it crosses Core Network.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..3

zxr10L2vpnPwPsnOutLabel1		1.3.6.1.4.1.3902.3.104.10.4.1.31
A 20-bit quantity containing a value that represents the botton of MPLS label stack.In L2VPN network, this label means the VC label.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..1048575

zxr10L2vpnPwPsnOutLabel2		1.3.6.1.4.1.3902.3.104.10.4.1.32
A 20-bit quantity containing a value that represents the second layer of MPLS label stack from the bottom of MPLS label.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..1048575

zxr10L2vpnPwPsnOutLabel3		1.3.6.1.4.1.3902.3.104.10.4.1.33
A 20-bit quantity containing a value that represents the third layer of MPLS label stack from the bottom of MPLS label.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..1048575

zxr10L2vpnPwPsnTunnelType		1.3.6.1.4.1.3902.3.104.10.4.1.34
The tunnel type of Core Network,including (1)LDP label (2)TE label,and (3)BGP label.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ldp(1), te(2), bgp(3)

zxr10L2vpnPwPsnTunnelId		1.3.6.1.4.1.3902.3.104.10.4.1.35
The tunnel ID number of Core Network.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..65535

zxr10L2vpnPwSwitchMacWithdraw		1.3.6.1.4.1.3902.3.104.10.4.1.36
The PW's local ability,whether the PW can send Mac-withdraw message.The bit is used to flag the presence as follows:Switch = 1 can send mac-withdraw message on this PW. Switch = 0 can't sent mac-withdraw message on this PW.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(0)

zxr10L2vpnPwServiceState		1.3.6.1.4.1.3902.3.104.10.4.1.37
The service-state of PW ,including (1)down, and (2) up,and (3)unknown.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(0), down(1), up(2)

zxr10L2vpnPwWorkState		1.3.6.1.4.1.3902.3.104.10.4.1.38
The work-state of PW ,including (1)down, and (2) active,and (3)standby,and (4)unknown.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(0), active(1), standby(2), down(3)

zxr10L2vpnPwSwitchSplitHorizone		1.3.6.1.4.1.3902.3.104.10.4.1.39
Split-horizon attribute which used in E-tree service includes two types on/off
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	null(0), on(1), off(2)

zxr10L3vpnPwSwitchGroupID		1.3.6.1.4.1.3902.3.104.10.4.1.40
Split-horizon-Group attribute .
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..64

zxr10L2vpnServiceTable		1.3.6.1.4.1.3902.3.104.10.5
Service Table. This table contains one entry per Service table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Zxr10L2vpnServiceEntry

zxr10L2vpnServiceEntry		1.3.6.1.4.1.3902.3.104.10.5.1
The parameter of a Service entity containing
Status: current	Access: not-accessible
OBJECT-TYPE
	Zxr10L2vpnServiceEntry

zxr10L2vpnServiceName		1.3.6.1.4.1.3902.3.104.10.5.1.1
The name of the service instance.It consists of 'Forwarder' modules connected by pseudowires and Attach Circuit.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

zxr10L2vpnServiceType		1.3.6.1.4.1.3902.3.104.10.5.1.2
The type of service instance.There are several types of L2VPNs:(1)Virtual Private LAN Service(VPLS), and (2)Virtual Private Wire Service(VPWS) (3)Multi-segment Pseudowire(MSPW),and (4)Virtual Local Switching Service(VLSS),and (5)Enhanced-Virtual Private Wire Service(Enhanced-VPWS)
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(0), vpls(1), vpws(2), mspw(3), vlss(4), enhanced-vpws(6)

zxr10L2vpnServiceSac1Name		1.3.6.1.4.1.3902.3.104.10.5.1.3
The first name of Service Attachment Circuit(SAC).
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

zxr10L2vpnServiceSac2Name		1.3.6.1.4.1.3902.3.104.10.5.1.4
The second name of Service Attachment Circuit(SAC).
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

zxr10L2vpnServiceSdu1Name		1.3.6.1.4.1.3902.3.104.10.5.1.5
The first name of Service Distribution Unit (SDU).
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

zxr10L2vpnServiceSdu2Name		1.3.6.1.4.1.3902.3.104.10.5.1.6
The second name of Service Distribution Unit (SDU).
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

zxr10L2vpnServiceMTU		1.3.6.1.4.1.3902.3.104.10.5.1.7
The VPLS's MTU value.This is the Maximum Transmission Unit,excluding encapsulation overhead, of the egresspacket interface that will be transmitting the decapsulated PDUthat is received from the MPLS-enabled network. This parameter is applicable only to PWs transporting packets and is REQUIRED for these PW types.If this parameter does not match in both directions of a specific PW, that PW MUST NOT be enabled.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	68..9216

zxr10L2vpnServiceMspwFirstPwPeer		1.3.6.1.4.1.3902.3.104.10.5.1.8
The PW's remote endpoint address.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

zxr10L2vpnServiceMspwFirstPwVcid		1.3.6.1.4.1.3902.3.104.10.5.1.9
A non-zero 32-bit connection ID that, together with the PW type, identifies a particular PW. Note that the PW ID and the PW type MUST be the same at both endpoints.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

zxr10L2vpnServiceMspwFirstPWVcType		1.3.6.1.4.1.3902.3.104.10.5.1.10
A 15-bit quantity containing a value that represents the type of PW. Assigned values are specified in 'IANA Allocations for Pseudowire Edge to Edge Emulation (PWE3)'.
Status: current	Access: read-only
OBJECT-TYPE
	L2vpnPWType

zxr10L2vpnServiceMspwSecondPwPeer		1.3.6.1.4.1.3902.3.104.10.5.1.11
The PW's remote endpoint address.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

zxr10L2vpnServiceMspwSecondPwVcid		1.3.6.1.4.1.3902.3.104.10.5.1.12
A non-zero 32-bit connection ID that, together with the PW type, identifies a particular PW. Note that the PW ID and the PW type MUST be the same at both endpoints.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4294967295

zxr10L2vpnServiceMspwSecondPwVcType		1.3.6.1.4.1.3902.3.104.10.5.1.13
A 15-bit quantity containing a value that represents the type of PW. Assigned values are specified in 'IANA Allocations for Pseudowire Edge to Edge Emulation (PWE3)'.
Status: current	Access: read-only
OBJECT-TYPE
	L2vpnPWType

zxr10L2vpnVplsTable		1.3.6.1.4.1.3902.3.104.10.6
Vpls Table. This table contains one entry per Vpls table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Zxr10L2vpnVplsEntry

zxr10L2vpnVplsEntry		1.3.6.1.4.1.3902.3.104.10.6.1
The parameter of a Vpls entity containing
Status: current	Access: not-accessible
OBJECT-TYPE
	Zxr10L2vpnVplsEntry

zxr10L2vpnVplsName		1.3.6.1.4.1.3902.3.104.10.6.1.1
The name of VPLS instance.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

zxr10L2vpnVplsApplication		1.3.6.1.4.1.3902.3.104.10.6.1.2
The type of service instance.There are several types of L2VPNs:(1)Virtual Private LAN Service(VPLS), and (2)Enhanced-Virtual Private LAN Service(Enhanced-VPLS), and (3)Enhanced-Virtual Private Wire Service(Enhanced-VPWS)
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(0), vpls(1), enhanced-vpls(5), enhanced-vpws(6)

zxr10L2vpnVplsModelType		1.3.6.1.4.1.3902.3.104.10.6.1.3
The model of the instance.It consists of (1)rfc4447model2(0) and (2)rfc4447model3(1).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	rfc4664model2(0), rfc4664model3(1)

zxr10L2vpnVplsServiceMTU		1.3.6.1.4.1.3902.3.104.10.6.1.4
The VPLS's MTU value.This is the Maximum Transmission Unit,excluding encapsulation overhead, of the egresspacket interface that will be transmitting the decapsulated PDUthat is received from the MPLS-enabled network. This parameter is applicable only to PWs transporting packets and is REQUIRED for these PW types.If this parameter does not match in both directions of a specific PW, that PW MUST NOT be enabled.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	68..9216

zxr10L2vpnVplsSwitchMacLearning		1.3.6.1.4.1.3902.3.104.10.6.1.5
L2vpn VPLS MAC learning switch.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(0)

zxr10L2vpnVplsSwitchMacAging		1.3.6.1.4.1.3902.3.104.10.6.1.6
L2vpn VPLS MAC aging time switch.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(0)

zxr10L2vpnVplsSwitchStatistics		1.3.6.1.4.1.3902.3.104.10.6.1.7
L2vpn VPLS MAC statistics time switch.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(0)

zxr10L2vpnVplsSwitchMacWithdraw		1.3.6.1.4.1.3902.3.104.10.6.1.8
L2vpn VPLS MAC withdraw time switch.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	on(1), off(0)

zxr10L2vpnVplsTimerMacAging		1.3.6.1.4.1.3902.3.104.10.6.1.9
L2vpn VPLS MAC aging timer.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	60..630

zxr10L2vpnVplsAntimovePolicy		1.3.6.1.4.1.3902.3.104.10.6.1.10
L2vpn VPLS anitmove policy.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unfixed(0), local-fixed(1), remote-fixed(2)

zxr10L2vpnVplsL2ptPolicyLACP		1.3.6.1.4.1.3902.3.104.10.6.1.11
L2vpn VPLS L2pt policy for LACP.
Status: current	Access: read-only
OBJECT-TYPE
	L2vpnVplsPolicy

zxr10L2vpnVplsL2ptPolicyDot1X		1.3.6.1.4.1.3902.3.104.10.6.1.12
L2vpn VPLS L2pt policy for Dot1x.
Status: current	Access: read-only
OBJECT-TYPE
	L2vpnVplsPolicy

zxr10L2vpnVplsL2ptPolicyGARP		1.3.6.1.4.1.3902.3.104.10.6.1.13
L2vpn VPLS L2pt policy for GARP.
Status: current	Access: read-only
OBJECT-TYPE
	L2vpnVplsPolicy

zxr10L2vpnVplsL2ptPolicySTP		1.3.6.1.4.1.3902.3.104.10.6.1.14
L2vpn VPLS L2pt policy for STP.
Status: current	Access: read-only
OBJECT-TYPE
	L2vpnVplsPolicy

zxr10L2vpnVplsL2ptPolicyLLDP		1.3.6.1.4.1.3902.3.104.10.6.1.15
L2vpn VPLS L2pt policy for LLDP.
Status: current	Access: read-only
OBJECT-TYPE
	L2vpnVplsPolicy

zxr10L2vpnVplsL2ptPolicyDot3X		1.3.6.1.4.1.3902.3.104.10.6.1.16
L2vpn VPLS L2pt policy for Dot3X.
Status: current	Access: read-only
OBJECT-TYPE
	L2vpnVplsPolicy

zxr10L2vpnVplsL2ptPolicyALL		1.3.6.1.4.1.3902.3.104.10.6.1.17
L2vpn VPLS L2pt policy for ALL.
Status: current	Access: read-only
OBJECT-TYPE
	L2vpnVplsPolicy

zxr10L2vpnVplsL2ptPolicyAllBridgeMulticast		1.3.6.1.4.1.3902.3.104.10.6.1.18
L2vpn VPLS L2pt policy for AllBridgeMulticast.
Status: current	Access: read-only
OBJECT-TYPE
	L2vpnVplsPolicy

zxr10L2vpnVplsL2ptPolicyZDPZTP		1.3.6.1.4.1.3902.3.104.10.6.1.19
L2vpn VPLS L2pt policy for ZDPZTP.
Status: current	Access: read-only
OBJECT-TYPE
	L2vpnVplsPolicy