TRANGOM5800S-MIB

File: TRANGOM5800S-MIB.mib (46940 bytes)

Imported modules

RFC1155-SMI RFC-1215 RFC-1212

Imported symbols

enterprises IpAddress Counter
TRAP-TYPE OBJECT-TYPE

Defined Types

DisplayString  
OCTET STRING    

SuInfoEntry  
SEQUENCE    
  suID INTEGER
  suMAC OCTET STRING
  suPolling INTEGER
  suSUtoSU INTEGER
  suCIR INTEGER
  suMIR INTEGER
  suIPAddr IpAddress
  suRemarks DisplayString
  suHWVer OCTET STRING
  suFWVer DisplayString
  suFPGAVer OCTET STRING
  suChecksum OCTET STRING
  suAssociation INTEGER
  suDIstance INTEGER
  suRSSIFromSU INTEGER
  suRSSIFromAP INTEGER
  suTxPower INTEGER
  suEthRxAvgThroughputLog INTEGER
  suEthTxAvgThroughputLog INTEGER
  suRfRxAvgThroughputLog INTEGER
  suRfTxAvgThroughputLog INTEGER
  suRfInOctets Counter
  suRfOutOctets Counter
  suPowerLevel INTEGER
  suTemperature INTEGER
  suReboot INTEGER

AptrpEntry  
SEQUENCE    
  aptrpIndex INTEGER
  aptrpID INTEGER
  aptrpCommStr DisplayString
  aptrpEnable INTEGER

Defined Values

trango 1.3.6.1.4.1.5454
OBJECT IDENTIFIER    

tbw 1.3.6.1.4.1.5454.1
OBJECT IDENTIFIER    

m5800sap 1.3.6.1.4.1.5454.1.10
OBJECT IDENTIFIER    

apsystem 1.3.6.1.4.1.5454.1.10.1
OBJECT IDENTIFIER    

aprf 1.3.6.1.4.1.5454.1.10.2
OBJECT IDENTIFIER    

su 1.3.6.1.4.1.5454.1.10.3
OBJECT IDENTIFIER    

trapconfig 1.3.6.1.4.1.5454.1.10.4
OBJECT IDENTIFIER    

mibinfo 1.3.6.1.4.1.5454.1.10.5
OBJECT IDENTIFIER    

m5800straps 1.3.6.1.4.1.5454.1.10.16
OBJECT IDENTIFIER    

apversion 1.3.6.1.4.1.5454.1.10.1.1
OBJECT IDENTIFIER    

apswitches 1.3.6.1.4.1.5454.1.10.1.13
OBJECT IDENTIFIER    

aptraffic 1.3.6.1.4.1.5454.1.10.1.15
OBJECT IDENTIFIER    

aprftable 1.3.6.1.4.1.5454.1.10.2.3
OBJECT IDENTIFIER    

apism 1.3.6.1.4.1.5454.1.10.2.4
OBJECT IDENTIFIER    

apunii 1.3.6.1.4.1.5454.1.10.2.5
OBJECT IDENTIFIER    

sudb 1.3.6.1.4.1.5454.1.10.3.5
OBJECT IDENTIFIER    

apsysHW 1.3.6.1.4.1.5454.1.10.1.1.1
Hardware version.
OBJECT-TYPE    
  OCTET STRING Size(2)  

apsysFW 1.3.6.1.4.1.5454.1.10.1.1.2
Main firmware version. Format: HD.
OBJECT-TYPE    
  DisplayString Size(0..80)  

apsysFPGA 1.3.6.1.4.1.5454.1.10.1.1.3
FPGA firmware version.
OBJECT-TYPE    
  OCTET STRING Size(4)  

apsysChecksum 1.3.6.1.4.1.5454.1.10.1.1.4
AP firmware checksum.
OBJECT-TYPE    
  OCTET STRING Size(4)  

apsysDeviceId 1.3.6.1.4.1.5454.1.10.1.2
MAC address.
OBJECT-TYPE    
  OCTET STRING Size(6)  

apsysBaseId 1.3.6.1.4.1.5454.1.10.1.3
Cluster that the AP belongs to. All APs and SUs in the same cluster shall have the same Base ID.
OBJECT-TYPE    
  INTEGER 0..127  

apsysAPId 1.3.6.1.4.1.5454.1.10.1.4
AP ID. Each AP in a cluster shall have unique AP ID.
OBJECT-TYPE    
  INTEGER 0..255  

apsysDefOpMode 1.3.6.1.4.1.5454.1.10.1.5
The operation mode (ap or off) the radio is on after reboot/power cycle.
OBJECT-TYPE    
  INTEGER ap(1), off(0)  

apsysCurOpMode 1.3.6.1.4.1.5454.1.10.1.6
Radio's current operation mode.
OBJECT-TYPE    
  INTEGER ap(1), off(0)  

apsysActivateOpmode 1.3.6.1.4.1.5454.1.10.1.7
Engage AP unit to ap operation mode.
OBJECT-TYPE    
  INTEGER deactivated(0), activateapmode(1)  

apsysIPAddr 1.3.6.1.4.1.5454.1.10.1.8
IP address.
OBJECT-TYPE    
  IpAddress  

apsysSubnet 1.3.6.1.4.1.5454.1.10.1.9
Subnet mask.
OBJECT-TYPE    
  IpAddress  

apsysDefaultGateway 1.3.6.1.4.1.5454.1.10.1.10
Default gateway.
OBJECT-TYPE    
  IpAddress  

apsysReadCommStr 1.3.6.1.4.1.5454.1.10.1.11
SNMP agent read community string. It is used for authentication purpose.
OBJECT-TYPE    
  DisplayString Size(0..32)  

apsysWriteCommStr 1.3.6.1.4.1.5454.1.10.1.12
SNMP agent write community string. It is used for authentication purpose.
OBJECT-TYPE    
  DisplayString Size(0..32)  

apsysBlockBroadcastMulticast 1.3.6.1.4.1.5454.1.10.1.13.1
This switch enables or disables the blocking of Ethernet control packet except ICMP and ARP to reduce the amount of uneccessary overhead introduced to the wireless link.
OBJECT-TYPE    
  INTEGER passed(0), blocked(1)  

apsysSUtoSU 1.3.6.1.4.1.5454.1.10.1.13.2
This switch enables or disables the peer-to-peer feature among SUs through the AP. Before this switch is turned on, all SUs that want to communicate with each other have to be assigned to the same group.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

apsysTFTPD 1.3.6.1.4.1.5454.1.10.1.13.4
This switch enables or disables the TFTP operation. When it is turned on, then the AP will be ready for code download.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

apsysHTTPD 1.3.6.1.4.1.5454.1.10.1.13.5
When it is turned on, then the AP is accessible for configuring via web browser (e.g. IE or Nescape).
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

apsysMIRThreshold 1.3.6.1.4.1.5454.1.10.1.14
Maximum Information Rate (in Kbps), the AP allows the network to utilize before enforcing CIR on each subscriber.
OBJECT-TYPE    
  INTEGER disabled(0), fourmbps(4), fivembps(5), sixmbps(6), sevenmbps(7), eightmbps(8)  

apsysEthRxAvgThroughputLog 1.3.6.1.4.1.5454.1.10.1.15.1
Average payload data throughput (in Kbits/sec) received on Ethernet port over the last 60 seconds.
OBJECT-TYPE    
  INTEGER  

apsysEthTxAvgThroughputLog 1.3.6.1.4.1.5454.1.10.1.15.2
Average payload data throughput (in Kbits/sec) transmitted on Ethernet port over the last 60 seconds.
OBJECT-TYPE    
  INTEGER  

apsysRfRxAvgThroughputLog 1.3.6.1.4.1.5454.1.10.1.15.3
Average payload data throughput (in Kbits/sec) received on RF port over the last 60 seconds.
OBJECT-TYPE    
  INTEGER  

apsysRfTxAvgThroughputLog 1.3.6.1.4.1.5454.1.10.1.15.4
Average payload data throughput (in Kbits/sec) transmitted on RF port over the last 60 seconds.
OBJECT-TYPE    
  INTEGER  

apsysEthInOctets 1.3.6.1.4.1.5454.1.10.1.15.5
Number of payload octets received on Ethernet port.
OBJECT-TYPE    
  Counter  

apsysEthOutOctets 1.3.6.1.4.1.5454.1.10.1.15.6
Number of payload octets transmitted on Ethernet port.
OBJECT-TYPE    
  Counter  

apsysRfInOctets 1.3.6.1.4.1.5454.1.10.1.15.7
Number of octets of SUs payload received from RF port.
OBJECT-TYPE    
  Counter  

apsysRfOutOctets 1.3.6.1.4.1.5454.1.10.1.15.8
Number of octets of SUs payload transmitted to RF port.
OBJECT-TYPE    
  Counter  

apsysTemperature 1.3.6.1.4.1.5454.1.10.1.16
Current AP temperature value (in Celsius).
OBJECT-TYPE    
  INTEGER -128..127  

apsysUpdateFlashAndActivate 1.3.6.1.4.1.5454.1.10.1.17
Save system setting values to Flash and activate the settings.
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

apsysReboot 1.3.6.1.4.1.5454.1.10.1.18
Reboot the radio.
OBJECT-TYPE    
  INTEGER deactivated(0), activated(1)  

aprfActiveChannel 1.3.6.1.4.1.5454.1.10.2.1
It specifies the current channel number the radio operates on.
OBJECT-TYPE    
  INTEGER 1..30  

aprfActivePolarization 1.3.6.1.4.1.5454.1.10.2.2
It specifies the current polarization the radio operates on.
OBJECT-TYPE    
  DisplayString Size(1)  

aprfChannel1 1.3.6.1.4.1.5454.1.10.2.3.1
RF channel 1 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
OBJECT-TYPE    
  INTEGER 5260..5340 | 5736..5836  

aprfChannel2 1.3.6.1.4.1.5454.1.10.2.3.2
RF channel 2 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
OBJECT-TYPE    
  INTEGER 5260..5340 | 5736..5836  

aprfChannel3 1.3.6.1.4.1.5454.1.10.2.3.3
RF channel 3 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
OBJECT-TYPE    
  INTEGER 5260..5340 | 5736..5836  

aprfChannel4 1.3.6.1.4.1.5454.1.10.2.3.4
RF channel 4 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
OBJECT-TYPE    
  INTEGER 5260..5340 | 5736..5836  

aprfChannel5 1.3.6.1.4.1.5454.1.10.2.3.5
RF channel 5 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
OBJECT-TYPE    
  INTEGER 5260..5340 | 5736..5836  

aprfChannel6 1.3.6.1.4.1.5454.1.10.2.3.6
RF channel 6 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
OBJECT-TYPE    
  INTEGER 5260..5340 | 5736..5836  

aprfChannel7 1.3.6.1.4.1.5454.1.10.2.3.7
RF channel 7 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
OBJECT-TYPE    
  INTEGER 5260..5340 | 5736..5836  

aprfChannel8 1.3.6.1.4.1.5454.1.10.2.3.8
RF channel 8 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
OBJECT-TYPE    
  INTEGER 5260..5340 | 5736..5836  

aprfChannel9 1.3.6.1.4.1.5454.1.10.2.3.9
RF channel 9 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
OBJECT-TYPE    
  INTEGER 5260..5340 | 5736..5836  

aprfChannel10 1.3.6.1.4.1.5454.1.10.2.3.10
RF channel 10 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
OBJECT-TYPE    
  INTEGER 5260..5340 | 5736..5836  

aprfChannel11 1.3.6.1.4.1.5454.1.10.2.3.11
RF channel 11 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
OBJECT-TYPE    
  INTEGER 5260..5340 | 5736..5836  

aprfChannel12 1.3.6.1.4.1.5454.1.10.2.3.12
RF channel 12 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
OBJECT-TYPE    
  INTEGER 5260..5340 | 5736..5836  

aprfChannel13 1.3.6.1.4.1.5454.1.10.2.3.13
RF channel 13 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
OBJECT-TYPE    
  INTEGER 5260..5340 | 5736..5836  

aprfChannel14 1.3.6.1.4.1.5454.1.10.2.3.14
RF channel 14 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
OBJECT-TYPE    
  INTEGER 5260..5340 | 5736..5836  

aprfChannel15 1.3.6.1.4.1.5454.1.10.2.3.15
RF channel 15 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
OBJECT-TYPE    
  INTEGER 5260..5340 | 5736..5836  

aprfChannel16 1.3.6.1.4.1.5454.1.10.2.3.16
RF channel 16 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
OBJECT-TYPE    
  INTEGER 5260..5340 | 5736..5836  

aprfChannel17 1.3.6.1.4.1.5454.1.10.2.3.17
RF channel 17 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
OBJECT-TYPE    
  INTEGER 5260..5340 | 5736..5836  

aprfChannel18 1.3.6.1.4.1.5454.1.10.2.3.18
RF channel 18 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
OBJECT-TYPE    
  INTEGER 5260..5340 | 5736..5836  

aprfChannel19 1.3.6.1.4.1.5454.1.10.2.3.19
RF channel 19 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
OBJECT-TYPE    
  INTEGER 5260..5340 | 5736..5836  

aprfChannel20 1.3.6.1.4.1.5454.1.10.2.3.20
RF channel 20 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
OBJECT-TYPE    
  INTEGER 5260..5340 | 5736..5836  

aprfChannel21 1.3.6.1.4.1.5454.1.10.2.3.21
RF channel 21 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
OBJECT-TYPE    
  INTEGER 5260..5340 | 5736..5836  

aprfChannel22 1.3.6.1.4.1.5454.1.10.2.3.22
RF channel 22 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
OBJECT-TYPE    
  INTEGER 5260..5340 | 5736..5836  

aprfChannel23 1.3.6.1.4.1.5454.1.10.2.3.23
RF channel 23 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
OBJECT-TYPE    
  INTEGER 5260..5340 | 5736..5836  

aprfChannel24 1.3.6.1.4.1.5454.1.10.2.3.24
RF channel 24 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
OBJECT-TYPE    
  INTEGER 5260..5340 | 5736..5836  

aprfChannel25 1.3.6.1.4.1.5454.1.10.2.3.25
RF channel 25 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
OBJECT-TYPE    
  INTEGER 5260..5340 | 5736..5836  

aprfChannel26 1.3.6.1.4.1.5454.1.10.2.3.26
RF channel 26 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
OBJECT-TYPE    
  INTEGER 5260..5340 | 5736..5836  

aprfChannel27 1.3.6.1.4.1.5454.1.10.2.3.27
RF channel 27 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
OBJECT-TYPE    
  INTEGER 5260..5340 | 5736..5836  

aprfChannel28 1.3.6.1.4.1.5454.1.10.2.3.28
RF channel 28 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
OBJECT-TYPE    
  INTEGER 5260..5340 | 5736..5836  

aprfChannel29 1.3.6.1.4.1.5454.1.10.2.3.29
RF channel 29 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
OBJECT-TYPE    
  INTEGER 5260..5340 | 5736..5836  

aprfChannel30 1.3.6.1.4.1.5454.1.10.2.3.30
RF channel 30 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
OBJECT-TYPE    
  INTEGER 5260..5340 | 5736..5836  

aprfismTxPowerMax 1.3.6.1.4.1.5454.1.10.2.4.1
The maximum ISM Tx power value can be set (in dBm).
OBJECT-TYPE    
  INTEGER -128..127  

aprfismTxPowerMin 1.3.6.1.4.1.5454.1.10.2.4.2
The minimum ISM Tx power value can be set (in dBm).
OBJECT-TYPE    
  INTEGER -128..127  

aprfismTxPower 1.3.6.1.4.1.5454.1.10.2.4.3
ISM RF tx power (in dBm). It specifies the power output of the radio, excluding the antenna gain. Check parameters aprfismTxPowerMax and aprfismTxPowerMin for power setting range.
OBJECT-TYPE    
  INTEGER -128..127  

aprfismServiceRadius 1.3.6.1.4.1.5454.1.10.2.4.4
ISM RF service radius (in mile). It specifies the distance of the furthest SU the AP will serve. Based on this information, the AP will determine the maximum wait time for a SU to response to a poll before it starts to poll the next one.
OBJECT-TYPE    
  INTEGER threemiles(3), tenmiles(10), thirtymiles(20)  

aprfismRxThreshold 1.3.6.1.4.1.5454.1.10.2.4.5
ISM RF rx threshold (in dBm). It specifies the receiver sensitivity of the AP. By default, the radio's sensitivity is -82dBm. The higher the threshold is, the less sensitive the radio will be. In M5800S, the value -90 represents the rfrxthreshold is disabled.
OBJECT-TYPE    
  INTEGER -90 | -85 | -80 | -75 | -70 | -65  

aprfismTargetRSSI 1.3.6.1.4.1.5454.1.10.2.4.6
ISM RF target RSSI (in dBm). It specifies the target RSSI from all SUs to the AP. Based on this parameter, the AP can power level each SU so that it receives same level of signal strength from all SUs, regardless far or near. Note that when you set the Target RSSI from SU, you need to consider AP's RF Rx Threshold value. The Target RSSI from SU must be 5dB higher than the RF Rx Threshold. When the RF Rx Threshold is disabled, the setting of the Target RSSI from SU shall be no less than -75dBm.
OBJECT-TYPE    
  INTEGER -85..-45  

aprfuniiTxPowerMax 1.3.6.1.4.1.5454.1.10.2.5.1
This object is only applicable to M5830S radio. The maximum UNII Tx power value can be set (in dBm).
OBJECT-TYPE    
  INTEGER -128..127  

aprfuniiTxPowerMin 1.3.6.1.4.1.5454.1.10.2.5.2
This object is only applicable to M5830S radio. The minimum UNII Tx power value can be set (in dBm).
OBJECT-TYPE    
  INTEGER -128..127  

aprfuniiTxPower 1.3.6.1.4.1.5454.1.10.2.5.3
This object is only applicable to M5830S radio. UNII RF tx power (in dBm). It specifies the power output of the radio, excluding the antenna gain. Check parameters aprfuniiTxPowerMax and aprfuniiTxPowerMin for power setting range.
OBJECT-TYPE    
  INTEGER -128..127  

aprfuniiServiceRadius 1.3.6.1.4.1.5454.1.10.2.5.4
This object is only applicable to M5830S radio. UNII RF service radius (in mile). It specifies the distance of the furthest SU the AP will serve. Based on this information, the AP will determine the maximum wait time for a SU to response to a poll before it starts to poll the next one.
OBJECT-TYPE    
  INTEGER twomiles(2), threemiles(3), fourmiles(4)  

aprfuniiRxThreshold 1.3.6.1.4.1.5454.1.10.2.5.5
This object is only applicable to M5830S radio. UNII RF rx threshold (in dBm). It specifies the receiver sensitivity of the AP.
OBJECT-TYPE    
  INTEGER -90 | -85 | -80 | -75 | -70 | -65  

aprfuniiTargetRSSI 1.3.6.1.4.1.5454.1.10.2.5.6
This object is only applicable to M5830S radio. UNII RF target RSSI (in dBm). It specifies the target RSSI from all SUs to the AP. Based on this parameter, the AP can power level each SU so that it receives same level of signal strength from all SUs, regardless far or near. Note that when you set the Target RSSI from SU, you need to consider AP's RF Rx Threshold value. The Target RSSI from SU must be 5dB higher than the RF Rx Threshold.
OBJECT-TYPE    
  INTEGER -85..-45  

suSUCount 1.3.6.1.4.1.5454.1.10.3.1
Number of subscriber units in the subscriber database.
OBJECT-TYPE    
  INTEGER 0..500  

suPowerLvlAll 1.3.6.1.4.1.5454.1.10.3.2
It is a feature that is typically found in more elaborate mobile systems such as cellular CDMA networks. Using this feature, all SUs have their RF power output adjusted until the signal strength for each SU as received in the AP is roughly the same.
OBJECT-TYPE    
  INTEGER deactivated(0), activated(1)  

suStatisticsSamplePeriod 1.3.6.1.4.1.5454.1.10.3.3
A period (in minute) AP requests update on SU Info Table from all associated SUs.
OBJECT-TYPE    
  INTEGER 1..60  

suRebootAll 1.3.6.1.4.1.5454.1.10.3.4
AP broadcasts reboot command to all subscriber units.
OBJECT-TYPE    
  INTEGER deactivated(0), activated(1)  

suAddOrDeleteID 1.3.6.1.4.1.5454.1.10.3.5.1
Subscriber unit ID (1..8190). Each subscriber in a sector shall have a unique ID.
OBJECT-TYPE    
  INTEGER 1..8190  

suAddMAC 1.3.6.1.4.1.5454.1.10.3.5.2
It is the MAC address of the subscriber unit, which can be found on the back of the SU.
OBJECT-TYPE    
  OCTET STRING Size(6)  

suAddPolling 1.3.6.1.4.1.5454.1.10.3.5.3
It is service level value, regular or priority, of a SU. The AP will poll priority user more often, thus better network latency as the result. As the network latency varies based on the number of subscriber units the AP serves, priority user is guaranteed that the latency is NOT greater than 100ms regardless of the size of the network.
OBJECT-TYPE    
  INTEGER regular(1), priority(5)  

suAddSUtoSU 1.3.6.1.4.1.5454.1.10.3.5.4
It is peer-to-peer group this SU belongs to. With the SU to SU switch is turned on, SUs in the same peer-to-peer group can communicate to each other via the AP. There are totally 15 groups available. Note that the SU shall be set to priority user for this feature to improve latency.
OBJECT-TYPE    
  INTEGER nullgroup(0), group1(1), group2(2), group3(3), group4(4), group5(5), group6(6), group7(7), group8(8), group9(9), groupA(10), groupB(11), groupC(12), groupD(13), groupE(14), groupF(15)  

suAddCIR 1.3.6.1.4.1.5454.1.10.3.5.5
It is the Committed Information Rate (in Kbps) the AP allocates to SU.
OBJECT-TYPE    
  INTEGER 0..9999  

suAddMIR 1.3.6.1.4.1.5454.1.10.3.5.6
It is the Maximum Information Rate (in Kbps) the AP allocates to SU.
OBJECT-TYPE    
  INTEGER 0..9999  

suAdd 1.3.6.1.4.1.5454.1.10.3.5.7
Add a subscriber (specified in object suAddOrDeleteID) to the subscriber database.
OBJECT-TYPE    
  INTEGER deactivated(0), add(1)  

suDelete 1.3.6.1.4.1.5454.1.10.3.5.8
Delete a subscriber (specified in object suAddOrDeleteID) from the subscriber database.
OBJECT-TYPE    
  INTEGER deactivated(0), delete(1)  

suInfoTable 1.3.6.1.4.1.5454.1.10.3.6
A table that contains subscriber unit entities.
OBJECT-TYPE    
  SEQUENCE OF  
    SuInfoEntry

suInfoEntry 1.3.6.1.4.1.5454.1.10.3.6.1
Information about a specific subscriber unit retrieved by its ID number.
OBJECT-TYPE    
  SuInfoEntry  

suID 1.3.6.1.4.1.5454.1.10.3.6.1.1
Subscriber unit ID. Each subscriber in a sector shall have a unique ID.
OBJECT-TYPE    
  INTEGER 1..8190  

suMAC 1.3.6.1.4.1.5454.1.10.3.6.1.2
Subscriber unit MAC Address. Format: 00 01 DE xx xx xx.
OBJECT-TYPE    
  OCTET STRING Size(6)  

suPolling 1.3.6.1.4.1.5454.1.10.3.6.1.3
It is service level value, regular or priority, of a SU. The AP will poll priority user more often, thus better network latency as the result. As the network latency varies based on the number of subscriber units the AP serves, priority user is guaranteed that the latency is NOT greater than 100ms regardless of the size of the network.
OBJECT-TYPE    
  INTEGER regular(1), priority(5)  

suSUtoSU 1.3.6.1.4.1.5454.1.10.3.6.1.4
It is peer-to-peer group this SU belongs to. With the SU to SU switch is turned on, SUs in the same peer-to-peer group can communicate to each other via the AP. There are totally 15 groups available. Note that the SU shall be set to priority user for this feature to improve latency.
OBJECT-TYPE    
  INTEGER nullgroup(0), group1(1), group2(2), group3(3), group4(4), group5(5), group6(6), group7(7), group8(8), group9(9), groupA(10), groupB(11), groupC(12), groupD(13), groupE(14), groupF(15)  

suCIR 1.3.6.1.4.1.5454.1.10.3.6.1.5
It is the Committed Information Rate (in Kbps) the AP allocates to SU.
OBJECT-TYPE    
  INTEGER 0..9999  

suMIR 1.3.6.1.4.1.5454.1.10.3.6.1.6
It is the Maximum Information Rate (in Kbps) the AP allocates to SU.
OBJECT-TYPE    
  INTEGER 0..9999  

suIPAddr 1.3.6.1.4.1.5454.1.10.3.6.1.7
Subscriber unit IP Address.
OBJECT-TYPE    
  IpAddress  

suRemarks 1.3.6.1.4.1.5454.1.10.3.6.1.8
Subscriber unit Remark.
OBJECT-TYPE    
  DisplayString Size(0..30)  

suHWVer 1.3.6.1.4.1.5454.1.10.3.6.1.9
Subscriber unit Hardware Version.
OBJECT-TYPE    
  OCTET STRING Size(2)  

suFWVer 1.3.6.1.4.1.5454.1.10.3.6.1.10
Subscriber unit main firmware version.
OBJECT-TYPE    
  DisplayString Size(0..32)  

suFPGAVer 1.3.6.1.4.1.5454.1.10.3.6.1.11
Subscriber unit FPGA firmware version.
OBJECT-TYPE    
  OCTET STRING Size(4)  

suChecksum 1.3.6.1.4.1.5454.1.10.3.6.1.12
Subscriber unit firmware checksum.
OBJECT-TYPE    
  OCTET STRING Size(4)  

suAssociation 1.3.6.1.4.1.5454.1.10.3.6.1.13
Subscriber unit association status.
OBJECT-TYPE    
  INTEGER associated(1), notAssociated(0)  

suDIstance 1.3.6.1.4.1.5454.1.10.3.6.1.14
Distance of SU (in mile).
OBJECT-TYPE    
  INTEGER 0..40  

suRSSIFromSU 1.3.6.1.4.1.5454.1.10.3.6.1.15
Subscriber unit RSSI from SU (in dBm).
OBJECT-TYPE    
  INTEGER -128..127  

suRSSIFromAP 1.3.6.1.4.1.5454.1.10.3.6.1.16
Subscriber unit RSSI from AP (in dBm).
OBJECT-TYPE    
  INTEGER -128..127  

suTxPower 1.3.6.1.4.1.5454.1.10.3.6.1.17
Subscriber unit Tx Power Level (in dBm).
OBJECT-TYPE    
  INTEGER -128..127  

suEthRxAvgThroughputLog 1.3.6.1.4.1.5454.1.10.3.6.1.18
Average payload data throughput (in Kbits/sec) received on the Ethernet port over the period specified by suStatisticsSamplePeriod.
OBJECT-TYPE    
  INTEGER  

suEthTxAvgThroughputLog 1.3.6.1.4.1.5454.1.10.3.6.1.19
Average payload data throughput (in Kbits/sec) transmitted on the Ethernet port over the period specified by suStatisticsSamplePeriod.
OBJECT-TYPE    
  INTEGER  

suRfRxAvgThroughputLog 1.3.6.1.4.1.5454.1.10.3.6.1.20
Average payload data throughput (in Kbits/sec) received on the RF port over the period specified by suStatisticsSamplePeriod.
OBJECT-TYPE    
  INTEGER  

suRfTxAvgThroughputLog 1.3.6.1.4.1.5454.1.10.3.6.1.21
Average payload data throughput (in Kbits/sec) transmitted on the RF port over the period specified by suStatisticsSamplePeriod.
OBJECT-TYPE    
  INTEGER  

suRfInOctets 1.3.6.1.4.1.5454.1.10.3.6.1.22
Number of payload octets received on the RF port.
OBJECT-TYPE    
  Counter  

suRfOutOctets 1.3.6.1.4.1.5454.1.10.3.6.1.23
Number of payload octets transmitted on the RF port.
OBJECT-TYPE    
  Counter  

suPowerLevel 1.3.6.1.4.1.5454.1.10.3.6.1.24
It is a feature that is typically found in more elaborate mobile systems such as cellular CDMA networks. Using this feature, the SU has its RF power output adjusted until its signal strength received in the AP is roughly the same.
OBJECT-TYPE    
  INTEGER deactivated(0), activated(1)  

suTemperature 1.3.6.1.4.1.5454.1.10.3.6.1.25
Subscriber Unit temperature reading value (in Celsius).
OBJECT-TYPE    
  INTEGER -128..127  

suReboot 1.3.6.1.4.1.5454.1.10.3.6.1.26
AP issues reboot command to a specific subscriber unit.
OBJECT-TYPE    
  INTEGER deactivated(0), activated(1)  

aptrpCount 1.3.6.1.4.1.5454.1.10.4.1
Types of trap.
OBJECT-TYPE    
  INTEGER 0..255  

aptrpDest1IPAddress 1.3.6.1.4.1.5454.1.10.4.2
Trap destination 1 IP address.
OBJECT-TYPE    
  IpAddress  

aptrpDest2IPAddress 1.3.6.1.4.1.5454.1.10.4.3
Trap destination 2 IP address.
OBJECT-TYPE    
  IpAddress  

aptrpTable 1.3.6.1.4.1.5454.1.10.4.4
A table that contains information of Trango trap events .
OBJECT-TYPE    
  SEQUENCE OF  
    AptrpEntry

aptrpEntry 1.3.6.1.4.1.5454.1.10.4.4.1
Information about a specific Trango trap event.
OBJECT-TYPE    
  AptrpEntry  

aptrpIndex 1.3.6.1.4.1.5454.1.10.4.4.1.1
Trap index.
OBJECT-TYPE    
  INTEGER 1..5  

aptrpID 1.3.6.1.4.1.5454.1.10.4.4.1.2
Specific trap ID.
OBJECT-TYPE    
  INTEGER 7..255  

aptrpCommStr 1.3.6.1.4.1.5454.1.10.4.4.1.3
Specific trap community string.
OBJECT-TYPE    
  DisplayString Size(0..32)  

aptrpEnable 1.3.6.1.4.1.5454.1.10.4.4.1.4
Enable a specific Trango trap event or not.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

mibinfoVersion 1.3.6.1.4.1.5454.1.10.5.1
Trango MIB Version.
OBJECT-TYPE    
  DisplayString Size(0..32)  

suLinkUp 7
The SNMP trap that is generated when a specific SU Associated.
TRAP-TYPE    

suLinkDown 8
The SNMP trap that is generated when a specific SU Powered Off.
TRAP-TYPE    

apOpModeFailure 9
The SNMP trap that is generated when a specific AP not being in ap mode during boot up sequence.
TRAP-TYPE