TN-QOS-EXT-MIB

File: TN-QOS-EXT-MIB.mib (84995 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
INET-ADDRESS-MIB ENTITY-MIB Q-BRIDGE-MIB
IF-MIB TRANSITION-SMI

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Counter32
Counter64 TruthValue TimeInterval
MacAddress RowStatus TEXTUAL-CONVENTION
MODULE-COMPLIANCE OBJECT-GROUP InetAddress
InetAddressType entPhysicalIndex VlanIndex
PortList InterfaceIndexOrZero InterfaceIndex
ifIndex tnProducts

Defined Types

TnQosExtRateUnitType  
T
TEXTUAL-CONVENTION    
  INTEGER kbps(1), fps(2), mbps(3), kfps(4)  

TnQosExtRateInFps  
T
TEXTUAL-CONVENTION    
  INTEGER fps1(1), fps2(2), fps4(3), fps8(4), fps16(5), fps32(6), fps64(7), fps128(8), fps256(9), fps512(10), fps1k(11), fps2k(12), fps4k(13), fps8k(14), fps16k(15), fps32k(16), fps64k(17), fps128k(18), fps256k(19), fps512k(20), fps1024k(21), fps2048k(22), fps4096k(23), fps8192k(24), fps16384k(25), fps32768k(26)  

TnQosExtPortPolicerEntry  
SEQUENCE    
  tnQosExtPortPolicerStatus INTEGER
  tnQosExtPortPolicerRate INTEGER
  tnQosExtPortPolicerUnit TnQosExtRateUnitType
  tnQosExtPortPolicerFlowControl INTEGER

TnQosExtPortQueuePolicerEntry  
SEQUENCE    
  tnQosExtPortQueuePolicerQid INTEGER
  tnQosExtPortQueuePolicerStatus INTEGER
  tnQosExtPortQueuePolicerRate INTEGER
  tnQosExtPortQueuePolicerUnit TnQosExtRateUnitType

TnQosExtPortSchedulerEntry  
SEQUENCE    
  tnQosExtPortSchedulerMode INTEGER
  tnQosExtPortSchedulerQueueMask BITS

TnQosExtPortSchedulerWeightEntry  
SEQUENCE    
  tnQosExtPortSchedulerWeightQid INTEGER
  tnQosExtPortSchedulerWeightVal INTEGER
  tnQosExtPortSchedulerWeightPercent INTEGER

TnQosExtPortShaperEntry  
SEQUENCE    
  tnQosExtPortShaperStatus INTEGER
  tnQosExtPortShaperRate INTEGER
  tnQosExtPortShaperUnit TnQosExtRateUnitType

TnQosExtPortQueueShaperEntry  
SEQUENCE    
  tnQosExtPortQueueShaperQid INTEGER
  tnQosExtPortQueueShaperStatus INTEGER
  tnQosExtPortQueueShaperRate INTEGER
  tnQosExtPortQueueShaperUnit TnQosExtRateUnitType
  tnQosExtPortQueueShaperExcess INTEGER

TnQosExtPortStormControlEntry  
SEQUENCE    
  tnQosExtPortStormControlUnicastStatus INTEGER
  tnQosExtPortStormControlUnicastRate TnQosExtRateInFps
  tnQosExtPortStormControlMulticastStatus INTEGER
  tnQosExtPortStormControlMulticastRate TnQosExtRateInFps
  tnQosExtPortStormControlBroadcastStatus INTEGER
  tnQosExtPortStormControlBroadcastRate TnQosExtRateInFps

TnQosExtPortStormControl2Entry  
SEQUENCE    
  tnQosExtPortStormControl2FrameType INTEGER
  tnQosExtPortStormControl2Rate INTEGER
  tnQosExtPortStormControl2RateUnit TnQosExtRateUnitType
  tnQosExtPortStormControl2Status TruthValue

TnQosExtPortWredEntry  
SEQUENCE    
  tnQosExtPortWredQid INTEGER
  tnQosExtPortWredEnable TruthValue
  tnQosExtPortWredThresholdMin INTEGER
  tnQosExtPortWredMaxDp1 INTEGER
  tnQosExtPortWredMaxDp2 INTEGER
  tnQosExtPortWredMaxDp3 INTEGER
  tnQosExtPortWredMaxThresh INTEGER
  tnQosExtPortWredMaxUnit INTEGER

TnQosExtPortPolicerOrderEntry  
SEQUENCE    
  tnQosExtPortPolicerOrder INTEGER

TnQosExtL2CosIfClassifDefaultEntry  
SEQUENCE    
  tnQosExtL2CosIfClassifDefaultClass INTEGER
  tnQosExtL2CosIfClassifDefaultDpl INTEGER
  tnQosExtL2CosIfClassifDefaultPcp INTEGER
  tnQosExtL2CosIfClassifDefaultDei INTEGER

TnQosExtL2CosIfClassifTagEntry  
SEQUENCE    
  tnQosExtL2CosIfClassifTagMode INTEGER

TnQosExtL2CosIfClassifTagMapEntry  
SEQUENCE    
  tnQosExtL2CosIfClassifTagMapPcp INTEGER
  tnQosExtL2CosIfClassifTagMapDei INTEGER
  tnQosExtL2CosIfClassifTagMapClass INTEGER
  tnQosExtL2CosIfClassifTagMapDpl INTEGER

TnQosExtL2CosIfTagRemarkingModeEntry  
SEQUENCE    
  tnQosExtL2CosIfTagRemarkingMode INTEGER

TnQosExtL2CosIfTagRemarkingDefaultEntry  
SEQUENCE    
  tnQosExtL2CosIfTagRemarkingDefaultPcp INTEGER
  tnQosExtL2CosIfTagRemarkingDefaultDei INTEGER

TnQosExtL2CosIfTagRemarkingMappingEntry  
SEQUENCE    
  tnQosExtL2CosIfTagRemarkingClass INTEGER
  tnQosExtL2CosIfTagRemarkingDpl INTEGER
  tnQosExtL2CosIfTagRemarkingPcp INTEGER
  tnQosExtL2CosIfTagRemarkingDei INTEGER

TnQosExtL2CosIfTagRemarkingDplMappingEntry  
SEQUENCE    
  tnQosExtL2CosIfTagRemarkingDplMappingClassifDpl INTEGER
  tnQosExtL2CosIfTagRemarkingDplMappingDpl INTEGER

TnQosExtDscpIfClassifBaseEntry  
SEQUENCE    
  tnQosExtDscpIfClassifBaseDscp INTEGER

TnQosExtDscpIfTransEntry  
SEQUENCE    
  tnQosExtDscpIfTransMode INTEGER

TnQosExtDscpIfTransMapEntry  
SEQUENCE    
  tnQosExtDscpIfTransMapDscp INTEGER
  tnQosExtDscpIfTransMapToDscp INTEGER

TnQosExtDscpClassifMapEntry  
SEQUENCE    
  tnQosExtDscpClassifMapDscp INTEGER
  tnQosExtDscpClassifMapTrust INTEGER
  tnQosExtDscpClassifMapClass INTEGER
  tnQosExtDscpClassifMapDpl INTEGER

TnQosExtDscpIfClassifExtEntry  
SEQUENCE    
  tnQosExtDscpIfClassifExtMode INTEGER

TnQosExtDscpIfClassifExtDscpEntry  
SEQUENCE    
  tnQosExtDscpIfClassifExtDscp INTEGER
  tnQosExtDscpIfClassifExtDscpMode INTEGER

TnQosExtDscpIfClassifExtMapEntry  
SEQUENCE    
  tnQosExtDscpIfClassifExtMapClass INTEGER
  tnQosExtDscpIfClassifExtMapDpl INTEGER
  tnQosExtDscpIfClassifExtMapDscp INTEGER

TnQosExtDscpIfEgressRemarkEntry  
SEQUENCE    
  tnQosExtDscpIfEgressRemarkMode INTEGER

TnQosExtDscpIfEgressRemarkMapEntry  
SEQUENCE    
  tnQosExtDscpIfEgressRemarkMapDscp INTEGER
  tnQosExtDscpIfEgressRemarkMapDpl INTEGER
  tnQosExtDscpIfEgressRemarkMapToDscp INTEGER

TnQosExtQclEntry  
SEQUENCE    
  tnQosExtQclIndex INTEGER
  tnQosExtQclId INTEGER
  tnQosExtQclNextQclId INTEGER
  tnQosExtQclPortList PortList
  tnQosExtQclTagType INTEGER
  tnQosExtQclTagVlanType INTEGER
  tnQosExtQclTagVlanVal VlanIndex
  tnQosExtQclTagVlanMin VlanIndex
  tnQosExtQclTagVlanMax VlanIndex
  tnQosExtQclTagPcp BITS
  tnQosExtQclTagDei INTEGER
  tnQosExtQclSMacType INTEGER
  tnQosExtQclSMac MacAddress
  tnQosExtQclDMacType INTEGER
  tnQosExtQclFrameType INTEGER
  tnQosExtQclActClassDefault INTEGER
  tnQosExtQclActClass INTEGER
  tnQosExtQclActDplDefault INTEGER
  tnQosExtQclActDpl INTEGER
  tnQosExtQclActDscpDefault INTEGER
  tnQosExtQclActDscp INTEGER
  tnQosExtQclConflict INTEGER
  tnQosExtQclStatus RowStatus

TnQosExtQclL2Entry  
SEQUENCE    
  tnQosExtQclEtherType INTEGER
  tnQosExtQclEtherVal INTEGER
  tnQosExtQclLlcSsapType INTEGER
  tnQosExtQclLlcSsapVal INTEGER
  tnQosExtQclLlcDsapType INTEGER
  tnQosExtQclLlcDsapVal INTEGER
  tnQosExtQclLlcControlType INTEGER
  tnQosExtQclLlcControlVal INTEGER
  tnQosExtQclSnapPidType INTEGER
  tnQosExtQclSnapPidVal INTEGER

TnQosExtQclIpEntry  
SEQUENCE    
  tnQosExtQclProtoType INTEGER
  tnQosExtQclProtoVal INTEGER
  tnQosExtQclDscpType INTEGER
  tnQosExtQclDscpVal INTEGER
  tnQosExtQclDscpMin INTEGER
  tnQosExtQclDscpMax INTEGER
  tnQosExtQclSrcIpType INTEGER
  tnQosExtQclSrcIpAddrType InetAddressType
  tnQosExtQclSrcIpAddr InetAddress
  tnQosExtQclSrcIpMaskType InetAddressType
  tnQosExtQclSrcIpMask InetAddress
  tnQosExtQclIpv4Fragment INTEGER
  tnQosExtQclTcpUdpSportType INTEGER
  tnQosExtQclTcpUdpSportVal INTEGER
  tnQosExtQclTcpUdpSportMin INTEGER
  tnQosExtQclTcpUdpSportMax INTEGER
  tnQosExtQclTcpUdpDportType INTEGER
  tnQosExtQclTcpUdpDportVal INTEGER
  tnQosExtQclTcpUdpDportMin INTEGER
  tnQosExtQclTcpUdpDportMax INTEGER

Defined Values

tnQosExtMIB 1.3.6.1.4.1.868.2.5.9
The mib module for managing extra QoS features in TN platform products.
MODULE-IDENTITY    

tnQosExtMIBObjects 1.3.6.1.4.1.868.2.5.9.1
OBJECT IDENTIFIER    

tnQosExtPortMgmt 1.3.6.1.4.1.868.2.5.9.1.1
OBJECT IDENTIFIER    

tnQosExtL2CosMgmt 1.3.6.1.4.1.868.2.5.9.1.2
OBJECT IDENTIFIER    

tnQosExtDscpMgmt 1.3.6.1.4.1.868.2.5.9.1.3
OBJECT IDENTIFIER    

tnQosExtQclMgmt 1.3.6.1.4.1.868.2.5.9.1.4
OBJECT IDENTIFIER    

tnQosExtPortPolicerTable 1.3.6.1.4.1.868.2.5.9.1.1.1
A port policer table can limit the bandwidth of received frames per port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TnQosExtPortPolicerEntry

tnQosExtPortPolicerEntry 1.3.6.1.4.1.868.2.5.9.1.1.1.1
An entry in the table controls the bandwidth of received frames per port. It is located in front of the ingress queue.
Status: current Access: not-accessible
OBJECT-TYPE    
  TnQosExtPortPolicerEntry  

tnQosExtPortPolicerStatus 1.3.6.1.4.1.868.2.5.9.1.1.1.1.1
Controls the per port policer status. The policer can limit the bandwidth of received frames. It is located in front of the Ingress queue.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

tnQosExtPortPolicerRate 1.3.6.1.4.1.868.2.5.9.1.1.1.1.2
Controls the rate for the port policer. The rate unit is defined in tnQosExtPortPolicerUnit.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

tnQosExtPortPolicerUnit 1.3.6.1.4.1.868.2.5.9.1.1.1.1.3
the rate unit for the port policer. Depend on the implement, some unit type may not be supported.
Status: current Access: read-write
OBJECT-TYPE    
  TnQosExtRateUnitType  

tnQosExtPortPolicerFlowControl 1.3.6.1.4.1.868.2.5.9.1.1.1.1.4
Controls the port policer flow control. If policer flow control is enabled and the port is in flow control mode, then pause frames are sent instead of discarding frames.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

tnQosExtPortQueuePolicerTable 1.3.6.1.4.1.868.2.5.9.1.1.2
A port queue policer table can limit the bandwidth of received frames per port per queue.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TnQosExtPortQueuePolicerEntry

tnQosExtPortQueuePolicerEntry 1.3.6.1.4.1.868.2.5.9.1.1.2.1
An entry in the table controls the bandwidth of received frames per port per queue. It is located in front of the ingress queue.
Status: current Access: not-accessible
OBJECT-TYPE    
  TnQosExtPortQueuePolicerEntry  

tnQosExtPortQueuePolicerQid 1.3.6.1.4.1.868.2.5.9.1.1.2.1.1
The ingress queue id for queue policer. tnQosExtPortQueuePolicerQid is a number in the range (0..(dot1dPortNumTrafficClasses-1))
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..11111  

tnQosExtPortQueuePolicerStatus 1.3.6.1.4.1.868.2.5.9.1.1.2.1.2
Controls whether the policer is enabled on the specific queue.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

tnQosExtPortQueuePolicerRate 1.3.6.1.4.1.868.2.5.9.1.1.2.1.3
Controls the rate for the queue policer. The rate unit is defined in tnQosExtPortQueuePolicerUnit.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

tnQosExtPortQueuePolicerUnit 1.3.6.1.4.1.868.2.5.9.1.1.2.1.4
The rate unit for the queue policer. Depend on the implement, some unit type may not be supported.
Status: current Access: read-write
OBJECT-TYPE    
  TnQosExtRateUnitType  

tnQosExtPortSchedulerTable 1.3.6.1.4.1.868.2.5.9.1.1.3
A port scheduler table controls the egress queue scheduler method per port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TnQosExtPortSchedulerEntry

tnQosExtPortSchedulerEntry 1.3.6.1.4.1.868.2.5.9.1.1.3.1
An entry in the table controls the egress queue scheduler method per port.
Status: current Access: not-accessible
OBJECT-TYPE    
  TnQosExtPortSchedulerEntry  

tnQosExtPortSchedulerMode 1.3.6.1.4.1.868.2.5.9.1.1.3.1.1
Controls the port egress scheduler mode, strict or weighted.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER strict(1), weighted(2)  

tnQosExtPortSchedulerQueueMask 1.3.6.1.4.1.868.2.5.9.1.1.3.1.2
Controls the queues mask which is in the weighted schedule mode. Other queues are in strict mode.
Status: current Access: read-write
OBJECT-TYPE    
  BITS none(0)  

tnQosExtPortSchedulerWeightTable 1.3.6.1.4.1.868.2.5.9.1.1.4
A port scheduler weight table controls the egress queue weight value in weighted scheduler mode per port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TnQosExtPortSchedulerWeightEntry

tnQosExtPortSchedulerWeightEntry 1.3.6.1.4.1.868.2.5.9.1.1.4.1
An entry in the table controls the egress queue weight value in weighted scheduler mode per port.
Status: current Access: not-accessible
OBJECT-TYPE    
  TnQosExtPortSchedulerWeightEntry  

tnQosExtPortSchedulerWeightQid 1.3.6.1.4.1.868.2.5.9.1.1.4.1.1
The egress queue id for scheduler. tnQosExtPortSchedulerWeightQid is a number in the range (0..(dot1dPortNumTrafficClasses-1))
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..11111  

tnQosExtPortSchedulerWeightVal 1.3.6.1.4.1.868.2.5.9.1.1.4.1.2
The egress queue weight value. the value range is from 1 to 100.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..100  

tnQosExtPortSchedulerWeightPercent 1.3.6.1.4.1.868.2.5.9.1.1.4.1.3
The egress queue weight in percent view.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

tnQosExtPortShaperTable 1.3.6.1.4.1.868.2.5.9.1.1.5
A port shaper table can limit the bandwidth of egress frames per port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TnQosExtPortShaperEntry

tnQosExtPortShaperEntry 1.3.6.1.4.1.868.2.5.9.1.1.5.1
An entry in the table controls the bandwidth of egress frames per port.
Status: current Access: not-accessible
OBJECT-TYPE    
  TnQosExtPortShaperEntry  

tnQosExtPortShaperStatus 1.3.6.1.4.1.868.2.5.9.1.1.5.1.1
Controls the per port shaper status. The shaper can limit the bandwidth of transmit frames in egress side.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

tnQosExtPortShaperRate 1.3.6.1.4.1.868.2.5.9.1.1.5.1.2
Controls the rate for the port shaper. The rate unit is defined in tnQosExtPortShaperUnit.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

tnQosExtPortShaperUnit 1.3.6.1.4.1.868.2.5.9.1.1.5.1.3
the rate unit for the port shaper. Depend on the implement, some unit type may not be supported.
Status: current Access: read-write
OBJECT-TYPE    
  TnQosExtRateUnitType  

tnQosExtPortQueueShaperTable 1.3.6.1.4.1.868.2.5.9.1.1.6
A port queue shaper table can limit the bandwidth of egress frames per port per queue.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TnQosExtPortQueueShaperEntry

tnQosExtPortQueueShaperEntry 1.3.6.1.4.1.868.2.5.9.1.1.6.1
An entry in the table controls the bandwidth of egress frames per port per queue.
Status: current Access: not-accessible
OBJECT-TYPE    
  TnQosExtPortQueueShaperEntry  

tnQosExtPortQueueShaperQid 1.3.6.1.4.1.868.2.5.9.1.1.6.1.1
The egress queue id for queue shaper. tnQosExtPortQueueShaperQid is a number in the range (0..(dot1dPortNumTrafficClasses-1))
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..11111  

tnQosExtPortQueueShaperStatus 1.3.6.1.4.1.868.2.5.9.1.1.6.1.2
Controls whether the shaper is enabled on the specific queue.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

tnQosExtPortQueueShaperRate 1.3.6.1.4.1.868.2.5.9.1.1.6.1.3
Controls the rate for the queue shaper. The rate unit is defined in tnQosExtPortQueueShaperUnit.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

tnQosExtPortQueueShaperUnit 1.3.6.1.4.1.868.2.5.9.1.1.6.1.4
The rate unit for the queue shaper. Depend on the implement, some unit type may not be supported.
Status: current Access: read-write
OBJECT-TYPE    
  TnQosExtRateUnitType  

tnQosExtPortQueueShaperExcess 1.3.6.1.4.1.868.2.5.9.1.1.6.1.5
Controls whether the queue is allowed to use excess bandwidth.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

tnQosExtPortStormControlTable 1.3.6.1.4.1.868.2.5.9.1.1.7
Storm control settings table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TnQosExtPortStormControlEntry

tnQosExtPortStormControlEntry 1.3.6.1.4.1.868.2.5.9.1.1.7.1
An entry in the table represents the storm control settings on an interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  TnQosExtPortStormControlEntry  

tnQosExtPortStormControlUnicastStatus 1.3.6.1.4.1.868.2.5.9.1.1.7.1.1
Enable or disable the storm control status for unicast.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

tnQosExtPortStormControlUnicastRate 1.3.6.1.4.1.868.2.5.9.1.1.7.1.2
The rate unit is packets per second (pps).
Status: current Access: read-write
OBJECT-TYPE    
  TnQosExtRateInFps  

tnQosExtPortStormControlMulticastStatus 1.3.6.1.4.1.868.2.5.9.1.1.7.1.3
Enable or disable the storm control status for multicast.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

tnQosExtPortStormControlMulticastRate 1.3.6.1.4.1.868.2.5.9.1.1.7.1.4
The rate unit is packets per second (pps).
Status: current Access: read-write
OBJECT-TYPE    
  TnQosExtRateInFps  

tnQosExtPortStormControlBroadcastStatus 1.3.6.1.4.1.868.2.5.9.1.1.7.1.5
Enable or disable the storm control status for broadcast.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

tnQosExtPortStormControlBroadcastRate 1.3.6.1.4.1.868.2.5.9.1.1.7.1.6
The rate unit is packets per second (pps).
Status: current Access: read-write
OBJECT-TYPE    
  TnQosExtRateInFps  

tnQosExtPortStormControl2Table 1.3.6.1.4.1.868.2.5.9.1.1.8
Storm control settings table 2.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TnQosExtPortStormControl2Entry

tnQosExtPortStormControl2Entry 1.3.6.1.4.1.868.2.5.9.1.1.8.1
An entry in the table represents the storm control settings on an interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  TnQosExtPortStormControl2Entry  

tnQosExtPortStormControl2FrameType 1.3.6.1.4.1.868.2.5.9.1.1.8.1.1
The frame type that storm control takes effect. Implement may use values like: unicast - unicast frame broadcast - broadcast frame unknown - unknown(flooding) frame
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER unicast(1), broadcast(2), unknown(3)  

tnQosExtPortStormControl2Rate 1.3.6.1.4.1.868.2.5.9.1.1.8.1.2
Controls the rate for the storm control. The rate unit is defined in tnQosExtPortStormControl2RateUnit
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

tnQosExtPortStormControl2RateUnit 1.3.6.1.4.1.868.2.5.9.1.1.8.1.3
Controls the rate unit for the storm control. The rate is defined in tnQosExtPortStormControl2Rate
Status: current Access: read-write
OBJECT-TYPE    
  TnQosExtRateUnitType  

tnQosExtPortStormControl2Status 1.3.6.1.4.1.868.2.5.9.1.1.8.1.4
Enable or disable the storm control status for the certain frame type.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

tnQosExtPortWredTable 1.3.6.1.4.1.868.2.5.9.1.1.9
A table used to configure the Weighted Random Early Detection feature.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TnQosExtPortWredEntry

tnQosExtPortWredEntry 1.3.6.1.4.1.868.2.5.9.1.1.9.1
An entry in the table used to configure the Weighted Random Early Detection feature.
Status: current Access: not-accessible
OBJECT-TYPE    
  TnQosExtPortWredEntry  

tnQosExtPortWredQid 1.3.6.1.4.1.868.2.5.9.1.1.9.1.1
The queue id for the weighted random early detection.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..11111  

tnQosExtPortWredEnable 1.3.6.1.4.1.868.2.5.9.1.1.9.1.2
Enable or disable the weighted random early detection for a certain traffic queue.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

tnQosExtPortWredThresholdMin 1.3.6.1.4.1.868.2.5.9.1.1.9.1.3
Controls the lower RED threshold for a certain traffic queue. If the average queue filling level is below this threshold, the drop probability is zero. This value is restricted to 0-100.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

tnQosExtPortWredMaxDp1 1.3.6.1.4.1.868.2.5.9.1.1.9.1.4
Controls the drop probability for frames marked with Drop Precedence Level 1 when the average queue filling level is 100%. This value is restricted to 0-100.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

tnQosExtPortWredMaxDp2 1.3.6.1.4.1.868.2.5.9.1.1.9.1.5
Controls the drop probability for frames marked with Drop Precedence Level 2 when the average queue filling level is 100%. This value is restricted to 0-100.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

tnQosExtPortWredMaxDp3 1.3.6.1.4.1.868.2.5.9.1.1.9.1.6
Controls the drop probability for frames marked with Drop Precedence Level 3 when the average queue filling level is 100%. This value is restricted to 0-100.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

tnQosExtPortWredMaxThresh 1.3.6.1.4.1.868.2.5.9.1.1.9.1.7
Controls the upper RED drop probability or fill level threshold for frames marked with Drop Precedence Level 1 (yellow frames). This value is restricted to 1-100%.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

tnQosExtPortWredMaxUnit 1.3.6.1.4.1.868.2.5.9.1.1.9.1.8
Selects the unit for Max. Threshold. Possible values are: Drop Probability: Max. Threshold controls the drop probability just below 100% fill level. Fill Level: Max. Threshold controls the fill level where drop probability reaches 100%.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER drop(1), fill(2)  

tnQosExtPortPolicerOrderTable 1.3.6.1.4.1.868.2.5.9.1.1.10
A table used to configure the QoS Policer Order per port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TnQosExtPortPolicerOrderEntry

tnQosExtPortPolicerOrderEntry 1.3.6.1.4.1.868.2.5.9.1.1.10.1
An entry in the table used to configure the QoS Policer Order per port.
Status: current Access: not-accessible
OBJECT-TYPE    
  TnQosExtPortPolicerOrderEntry  

tnQosExtPortPolicerOrder 1.3.6.1.4.1.868.2.5.9.1.1.10.1.1
QoS policer order on the entry. depend on implement, the valid policer order would be: 1 - in this mode, QoS policer order is Port Queue Policer first, then Port Policer, ACL Policer is the last (default). 2 - in this mode, QoS policer order is ACL Policer first, then Port Queue Policer, Port Policer is the last.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

tnQosExtL2CosIfClassifDefaultTable 1.3.6.1.4.1.868.2.5.9.1.2.1
Qos layer 2 default Ingress Classification table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TnQosExtL2CosIfClassifDefaultEntry

tnQosExtL2CosIfClassifDefaultEntry 1.3.6.1.4.1.868.2.5.9.1.2.1.1
An entry in the table represents the QoS layer 2 default Ingress Classification settings on an interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  TnQosExtL2CosIfClassifDefaultEntry  

tnQosExtL2CosIfClassifDefaultClass 1.3.6.1.4.1.868.2.5.9.1.2.1.1.1
Controls the default QoS class (the QoS class for frames not classified in any other way). There is a one to one mapping between QoS class, queue and priority. A QoS class of 0 (zero) has the lowest priority. tnQosExtL2CosIfClassifDefaultClass is a number in the range (0..(dot1dPortNumTrafficClasses-1))
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

tnQosExtL2CosIfClassifDefaultDpl 1.3.6.1.4.1.868.2.5.9.1.2.1.1.2
Controls the default DP (Drop Precedence) level for frames not classified in any other way.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

tnQosExtL2CosIfClassifDefaultPcp 1.3.6.1.4.1.868.2.5.9.1.2.1.1.3
Controls the default PCP for untagged frames. PCP (Priority Code Point) is a 3-bit field storing the priority level for the 802.1Q frame. It is also known as User Priority.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

tnQosExtL2CosIfClassifDefaultDei 1.3.6.1.4.1.868.2.5.9.1.2.1.1.4
Controls the default DEI for untagged frames. DEI (Drop Eligible Indicator) is a 1-bit field in the VLAN tag.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..1  

tnQosExtL2CosIfClassifTagTable 1.3.6.1.4.1.868.2.5.9.1.2.2
Layer 2 Cos ingress priority-tagged frame classification mode Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TnQosExtL2CosIfClassifTagEntry

tnQosExtL2CosIfClassifTagEntry 1.3.6.1.4.1.868.2.5.9.1.2.2.1
An entry in the table represents the Layer 2 Cos ingress priority-tagged frame classification mode on an interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  TnQosExtL2CosIfClassifTagEntry  

tnQosExtL2CosIfClassifTagMode 1.3.6.1.4.1.868.2.5.9.1.2.2.1.1
Controls the classification mode for priority tagged frames on this interface. Disabled - Use default QoS class and DP level for priority tagged frames. Enabled - Use mapped value of PCP and DEI for priority tagged frames.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

tnQosExtL2CosIfClassifTagMapTable 1.3.6.1.4.1.868.2.5.9.1.2.3
classified (PCP, DEI) to (QoS class, DP level) mapping table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TnQosExtL2CosIfClassifTagMapEntry

tnQosExtL2CosIfClassifTagMapEntry 1.3.6.1.4.1.868.2.5.9.1.2.3.1
An entry in the table represents the mapping of the classified (PCP, DEI) to (QoS class, DP level) values. This mapping is valid when tnQosExtL2CosIfClassifTagMode is set to Enabled.
Status: current Access: not-accessible
OBJECT-TYPE    
  TnQosExtL2CosIfClassifTagMapEntry  

tnQosExtL2CosIfClassifTagMapPcp 1.3.6.1.4.1.868.2.5.9.1.2.3.1.1
The carried Pcp (Priority Code Point) field value if recieved frame is IEEE tagged frame.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 0..7  

tnQosExtL2CosIfClassifTagMapDei 1.3.6.1.4.1.868.2.5.9.1.2.3.1.2
The carried Dei (Drop Eligible Indicator) field value if recieved frame is IEEE tagged frame.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 0..1  

tnQosExtL2CosIfClassifTagMapClass 1.3.6.1.4.1.868.2.5.9.1.2.3.1.3
The Traffic Class the received frame is mapped to. tnQosExtL2CosIfClassifTagMapClass is a number in the range (0..(dot1dPortNumTrafficClasses-1)).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

tnQosExtL2CosIfClassifTagMapDpl 1.3.6.1.4.1.868.2.5.9.1.2.3.1.4
The DP (Drop Precedence) level the received frame is mapped to.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

tnQosExtL2CosIfTagRemarkingModeTable 1.3.6.1.4.1.868.2.5.9.1.2.4
A table can control the egress frame tag remarking mode on an interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TnQosExtL2CosIfTagRemarkingModeEntry

tnQosExtL2CosIfTagRemarkingModeEntry 1.3.6.1.4.1.868.2.5.9.1.2.4.1
An entry in the table controls the egress frame tag remarking mode on an interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  TnQosExtL2CosIfTagRemarkingModeEntry  

tnQosExtL2CosIfTagRemarkingMode 1.3.6.1.4.1.868.2.5.9.1.2.4.1.1
Controls the tag remarking mode for this port. Classified - Use classified PCP/DEI values. Default - Use default PCP/DEI values. Mapped - Use mapped versions of QoS class and DP level.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER classified(1), default(2), mapped(3)  

tnQosExtL2CosIfTagRemarkingDefaultTable 1.3.6.1.4.1.868.2.5.9.1.2.5
A table represents the egress frame tag remarking mapping per port, when tnQosExtL2CosIfTagRemarkingMode is set to default mode.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TnQosExtL2CosIfTagRemarkingDefaultEntry

tnQosExtL2CosIfTagRemarkingDefaultEntry 1.3.6.1.4.1.868.2.5.9.1.2.5.1
An entry in the table represents the egress frame tag remarking mapping per port, when tnQosExtL2CosIfTagRemarkingMode is set to default mode.
Status: current Access: not-accessible
OBJECT-TYPE    
  TnQosExtL2CosIfTagRemarkingDefaultEntry  

tnQosExtL2CosIfTagRemarkingDefaultPcp 1.3.6.1.4.1.868.2.5.9.1.2.5.1.1
Default PCP (Priority Code Point) is a 3-bit field storing the priority level for the 802.1Q frame. It is also known as User Priority. The valid range is 0 - 7. The default is 0.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

tnQosExtL2CosIfTagRemarkingDefaultDei 1.3.6.1.4.1.868.2.5.9.1.2.5.1.2
Default DEI (Drop Eligible Indicator) is a 1-bit field in the VLAN tag. The valid range is 0 - 1. The default is 0.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..1  

tnQosExtL2CosIfTagRemarkingMappingTable 1.3.6.1.4.1.868.2.5.9.1.2.6
A table represents the egress frame tag remarking mapping per port, when tnQosExtL2CosIfTagRemarkingMode is set to mapping mode.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TnQosExtL2CosIfTagRemarkingMappingEntry

tnQosExtL2CosIfTagRemarkingMappingEntry 1.3.6.1.4.1.868.2.5.9.1.2.6.1
An entry in the table represents the egress frame tag remarking mapping per port, when tnQosExtL2CosIfTagRemarkingMode is set to mapping mode.
Status: current Access: not-accessible
OBJECT-TYPE    
  TnQosExtL2CosIfTagRemarkingMappingEntry  

tnQosExtL2CosIfTagRemarkingClass 1.3.6.1.4.1.868.2.5.9.1.2.6.1.1
The traffic class of the transmit frame belongs to. tnQosExtIfTagRemarkingClass is a number in the range (0..(dot1dPortNumTrafficClasses-1)).
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..11111  

tnQosExtL2CosIfTagRemarkingDpl 1.3.6.1.4.1.868.2.5.9.1.2.6.1.2
The DP (Drop Precedence) level of the transmit frame belongs to.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..11111  

tnQosExtL2CosIfTagRemarkingPcp 1.3.6.1.4.1.868.2.5.9.1.2.6.1.3
PCP (Priority Code Point) is a 3-bit field storing the priority level for the 802.1Q frame. It is also known as User Priority. The valid range is 0 - 7.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

tnQosExtL2CosIfTagRemarkingDei 1.3.6.1.4.1.868.2.5.9.1.2.6.1.4
DEI (Drop Eligible Indicator) is a 1-bit field in the VLAN tag. The valid range is 0 - 1.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..1  

tnQosExtL2CosIfTagRemarkingDplMappingTable 1.3.6.1.4.1.868.2.5.9.1.2.7
A table represents the egress frame tag remarking DP level mapping per port, when tnQosExtL2CosIfTagRemarkingMode is set to mapping mode.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TnQosExtL2CosIfTagRemarkingDplMappingEntry

tnQosExtL2CosIfTagRemarkingDplMappingEntry 1.3.6.1.4.1.868.2.5.9.1.2.7.1
An entry in the table represents the egress frame tag remarking dpl mapping per port, when tnQosExtL2CosIfTagRemarkingMode is set to mapping mode.
Status: current Access: not-accessible
OBJECT-TYPE    
  TnQosExtL2CosIfTagRemarkingDplMappingEntry  

tnQosExtL2CosIfTagRemarkingDplMappingClassifDpl 1.3.6.1.4.1.868.2.5.9.1.2.7.1.1
The Classified DP (Drop Precedence) level of the transmit frame belongs to.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..11111  

tnQosExtL2CosIfTagRemarkingDplMappingDpl 1.3.6.1.4.1.868.2.5.9.1.2.7.1.2
The DP (Drop Precedence) level used for tag remarking process.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

tnQosExtDscpIfClassifBaseTable 1.3.6.1.4.1.868.2.5.9.1.3.1
A table represents the QoS classification mode basis on an interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TnQosExtDscpIfClassifBaseEntry

tnQosExtDscpIfClassifBaseEntry 1.3.6.1.4.1.868.2.5.9.1.3.1.1
An entry in the table represents the QoS classification mode basis on an interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  TnQosExtDscpIfClassifBaseEntry  

tnQosExtDscpIfClassifBaseDscp 1.3.6.1.4.1.868.2.5.9.1.3.1.1.1
Controls whether the QoS classification mode is based on DSCP value in IP frames on an interface. Disabled - Disable DSCP based classification. Enabled - Enable DSCP based classification.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

tnQosExtDscpIfTransTable 1.3.6.1.4.1.868.2.5.9.1.3.2
A table represents the DSCP ingress translation mode on an interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TnQosExtDscpIfTransEntry

tnQosExtDscpIfTransEntry 1.3.6.1.4.1.868.2.5.9.1.3.2.1
An entry in the table represents the DSCP ingress translation mode on an interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  TnQosExtDscpIfTransEntry  

tnQosExtDscpIfTransMode 1.3.6.1.4.1.868.2.5.9.1.3.2.1.1
Controls the ingress DSCP translation setting on an interface.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

tnQosExtDscpIfTransMapTable 1.3.6.1.4.1.868.2.5.9.1.3.3
A table perform the ingress DSCP translation on an interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TnQosExtDscpIfTransMapEntry

tnQosExtDscpIfTransMapEntry 1.3.6.1.4.1.868.2.5.9.1.3.3.1
A entry in this table perform the ingress DSCP translation on an interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  TnQosExtDscpIfTransMapEntry  

tnQosExtDscpIfTransMapDscp 1.3.6.1.4.1.868.2.5.9.1.3.3.1.1
The received frame carried DSCP value, used for DSCP transmit input. DSCP (Differentiated Services Code Point) is a field in the header of IP packets for packet classification purposes. The valid range is 0 - 63
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 0..63  

tnQosExtDscpIfTransMapToDscp 1.3.6.1.4.1.868.2.5.9.1.3.3.1.2
The mapping DSCP value from the frame DSCP value, used for DSCP classification. DSCP (Differentiated Services Code Point) is a field in the header of IP packets for packet classification purposes. The valid range is 0 - 63
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..63  

tnQosExtDscpClassifMapTable 1.3.6.1.4.1.868.2.5.9.1.3.4
A table represents the DSCP-Based QoS ingress classification mapping on an interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TnQosExtDscpClassifMapEntry

tnQosExtDscpClassifMapEntry 1.3.6.1.4.1.868.2.5.9.1.3.4.1
An entry in the table represents the DSCP-Based QoS ingress classification mapping on an interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  TnQosExtDscpClassifMapEntry  

tnQosExtDscpClassifMapDscp 1.3.6.1.4.1.868.2.5.9.1.3.4.1.1
DSCP value used to map Qos class and DPL is either translated DSCP value or incoming frame DSCP value.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 0..63  

tnQosExtDscpClassifMapTrust 1.3.6.1.4.1.868.2.5.9.1.3.4.1.2
Controls whether a specific DSCP value is trusted. Only frames with trused DSCP values are mapped to a specific QoS class and DPL. Frames with untrusted DSCP values are treated as a non-IP frame. Enabled - Set DSCP as trusted DSCP. Disabled - Set DSCP as un-trusted DSCP.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

tnQosExtDscpClassifMapClass 1.3.6.1.4.1.868.2.5.9.1.3.4.1.3
The traffic class of the recieved frame mapped to. tnQosExtDscpClassifMapClass is a number in the range (0..(dot1dPortNumTrafficClasses-1)).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

tnQosExtDscpClassifMapDpl 1.3.6.1.4.1.868.2.5.9.1.3.4.1.4
The DP (Drop Precedence) level of the transmit frame mapped to
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

tnQosExtDscpIfClassifExtTable 1.3.6.1.4.1.868.2.5.9.1.3.5
A table represents the DSCP classification based on QoS class and DP level on an interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TnQosExtDscpIfClassifExtEntry

tnQosExtDscpIfClassifExtEntry 1.3.6.1.4.1.868.2.5.9.1.3.5.1
An entry in the table represents the DSCP classification based on QoS class and DP level on an interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  TnQosExtDscpIfClassifExtEntry  

tnQosExtDscpIfClassifExtMode 1.3.6.1.4.1.868.2.5.9.1.3.5.1.1
Controls the ingress DSCP classification setting on an interface. Disable - No Ingress DSCP Classification. DSCP=0 - Classify if incoming (or translated if enabled) DSCP is 0. Selected: Classify only selected DSCP for which classification is enabled. All: Classify all DSCP.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), dscp0(2), selected(3), all(4)  

tnQosExtDscpIfClassifExtDscpTable 1.3.6.1.4.1.868.2.5.9.1.3.6
A table represents the DSCP classification mode per DSCP value.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TnQosExtDscpIfClassifExtDscpEntry

tnQosExtDscpIfClassifExtDscpEntry 1.3.6.1.4.1.868.2.5.9.1.3.6.1
An entry in the table represents the DSCP classification mode per DSCP value.
Status: current Access: not-accessible
OBJECT-TYPE    
  TnQosExtDscpIfClassifExtDscpEntry  

tnQosExtDscpIfClassifExtDscp 1.3.6.1.4.1.868.2.5.9.1.3.6.1.1
DSCP (Differentiated Services Code Point) is a field in the header of IP packets for packet classification purposes. The valid range is 0 - 63
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 0..63  

tnQosExtDscpIfClassifExtDscpMode 1.3.6.1.4.1.868.2.5.9.1.3.6.1.2
Control the DSCP ingress classification mode on an interface. If port DSCP classification is 'selected', DSCP will be classified based on QoS class and DP level only for DSCP value with classification mode 'enabled'. DSCP may be translated DSCP if translation is enabled for the port. Enabled - Enable DSCP ingress classification. Disabled - Disable DSCP ingress classification.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

tnQosExtDscpIfClassifExtMapTable 1.3.6.1.4.1.868.2.5.9.1.3.7
A table config the Dscp ingress classification mapping.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TnQosExtDscpIfClassifExtMapEntry

tnQosExtDscpIfClassifExtMapEntry 1.3.6.1.4.1.868.2.5.9.1.3.7.1
An entry in this table perform the Dscp ingress classification mapping.
Status: current Access: not-accessible
OBJECT-TYPE    
  TnQosExtDscpIfClassifExtMapEntry  

tnQosExtDscpIfClassifExtMapClass 1.3.6.1.4.1.868.2.5.9.1.3.7.1.1
The Traffic Class the received frame is mapped to. tnQosExtDscpIfClassifExtMapClass is a number in the range (0..(dot1dPortNumTrafficClasses-1)).
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..11111  

tnQosExtDscpIfClassifExtMapDpl 1.3.6.1.4.1.868.2.5.9.1.3.7.1.2
The DP (Drop Precedence) level the received frame is mapped to.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..11111  

tnQosExtDscpIfClassifExtMapDscp 1.3.6.1.4.1.868.2.5.9.1.3.7.1.3
The Classified DSCP from QoS class and DP level. The DSCP which needs to be classified depends on interface DSCP classification and DSCP classification mode. Incoming frame DSCP may be translated before using the value for classification.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..63  

tnQosExtDscpIfEgressRemarkTable 1.3.6.1.4.1.868.2.5.9.1.3.8
A table represents the DSCP egress remark mode on an interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TnQosExtDscpIfEgressRemarkEntry

tnQosExtDscpIfEgressRemarkEntry 1.3.6.1.4.1.868.2.5.9.1.3.8.1
An entry in the table represents the DSCP egress remark mode on an interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  TnQosExtDscpIfEgressRemarkEntry  

tnQosExtDscpIfEgressRemarkMode 1.3.6.1.4.1.868.2.5.9.1.3.8.1.1
Controls the egress frame DSCP field rewrite setting per port. Disable: No Egress rewrite. Enable: Rewrite enable without remapped. Remap DP Unaware: DSCP from analyzer is remapped and frame is remarked with remapped DSCP value. Remap DP Aware: DSCP from analyzer is remapped and frame is remarked with remapped DSCP value.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2), remapDpUnaware(3), remapDpAware(4)  

tnQosExtDscpIfEgressRemarkMapTable 1.3.6.1.4.1.868.2.5.9.1.3.9
A table represents the DSCP egress remark map on an interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TnQosExtDscpIfEgressRemarkMapEntry

tnQosExtDscpIfEgressRemarkMapEntry 1.3.6.1.4.1.868.2.5.9.1.3.9.1
An entry in the table represents the DSCP egress remark map on an interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  TnQosExtDscpIfEgressRemarkMapEntry  

tnQosExtDscpIfEgressRemarkMapDscp 1.3.6.1.4.1.868.2.5.9.1.3.9.1.1
The classified DSCP value of the specific IP frame, used for DSCP egress remark. DSCP valid range is 0 - 63
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 0..63  

tnQosExtDscpIfEgressRemarkMapDpl 1.3.6.1.4.1.868.2.5.9.1.3.9.1.2
The classified DP (Drop Precedence) level of the specific frame, used for DSCP egress remark.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..11111  

tnQosExtDscpIfEgressRemarkMapToDscp 1.3.6.1.4.1.868.2.5.9.1.3.9.1.3
The DSCP value to which you want to remap for the egress side. This remap is based on classified DSCP and DP level.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..63  

tnQosExtQclTable 1.3.6.1.4.1.868.2.5.9.1.4.1
A table used to configure the QoS Control List settings.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TnQosExtQclEntry

tnQosExtQclEntry 1.3.6.1.4.1.868.2.5.9.1.4.1.1
An entry in the table used to configure the QoS Control List settings.
Status: current Access: not-accessible
OBJECT-TYPE    
  TnQosExtQclEntry  

tnQosExtQclIndex 1.3.6.1.4.1.868.2.5.9.1.4.1.1.1
The row index of the QCL.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..11111  

tnQosExtQclId 1.3.6.1.4.1.868.2.5.9.1.4.1.1.2
The identifier of the QCL.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

tnQosExtQclNextQclId 1.3.6.1.4.1.868.2.5.9.1.4.1.1.3
Specify the created ECE is placed before which QCL.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

tnQosExtQclPortList 1.3.6.1.4.1.868.2.5.9.1.4.1.1.4
The list of port members for the QCL.
Status: current Access: read-create
OBJECT-TYPE    
  PortList  

tnQosExtQclTagType 1.3.6.1.4.1.868.2.5.9.1.4.1.1.5
The frame tag type for matching the QCL. The possible values are: tagged: The QCL will match tagged frames only. untagged: The QCL will match untagged frames only. any: The QCL will match both tagged and untagged frames.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER tagged(1), untagged(2), any(3)  

tnQosExtQclTagVlanType 1.3.6.1.4.1.868.2.5.9.1.4.1.1.6
The VLAN ID filter type for matching the QCL. It is only significant if tnQosExtQclTagType is 'tagged' or 'any'. The possible values are: any: No VLAN ID filter is specified. (VLAN ID filter status is 'don't-care'.) specific: If you want to filter a specific VLAN ID value with this QCL, choose this value. A field for entering a specific value appears. range: If you want to filter a specific VLAN ID range filter with this QCL, choose this value. A field for entering a range appears.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER any(1), specific(2), range(3)  

tnQosExtQclTagVlanVal 1.3.6.1.4.1.868.2.5.9.1.4.1.1.7
The Specific VLAN ID filter for matching the QCL. It is only significant if tnQosExtQclTagVlanType is selected 'specific'.
Status: current Access: read-create
OBJECT-TYPE    
  VlanIndex  

tnQosExtQclTagVlanMin 1.3.6.1.4.1.868.2.5.9.1.4.1.1.8
The Start of Range VLAN ID filter for matching the QCL. It is only significant if tnQosExtQclTagVlanType is selected 'range'. this value should be lower than tnQosExtQclTagVlanMax value.
Status: current Access: read-create
OBJECT-TYPE    
  VlanIndex  

tnQosExtQclTagVlanMax 1.3.6.1.4.1.868.2.5.9.1.4.1.1.9
The End of Range VLAN ID filter for matching the QCL. It is only significant if tnQosExtQclTagVlanType is selected 'range'. this value should be higher than tnQosExtQclTagVlanMin value.
Status: current Access: read-create
OBJECT-TYPE    
  VlanIndex  

tnQosExtQclTagPcp 1.3.6.1.4.1.868.2.5.9.1.4.1.1.10
The PCP value for mataching the QCL. It is only significant if tnQosExtQclTagType is 'tagged' or 'any'. The possible values are: any: The QCL will match any PCP value(all bits will be set to 1). specific: each bit matchs a specific PCP of QCL(from bit0 to bit7). range: The QCL will match PCP values in the selected range, valid range is depend on the specific implement. e.g: for S3280, the valid range are bit0-bit1, bit2-bit3, bit4-bit5, bit6-bit7, bit0-bit3 or bit4-bit7.
Status: current Access: read-create
OBJECT-TYPE    
  BITS none(0)  

tnQosExtQclTagDei 1.3.6.1.4.1.868.2.5.9.1.4.1.1.11
The DEI value for mataching the QCL. It is only significant if tnQosExtQclTagType is 'tagged' or 'any'. The possible values are: 'any', 'dei0' or 'dei1'.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER any(1), dei0(2), dei1(3)  

tnQosExtQclSMacType 1.3.6.1.4.1.868.2.5.9.1.4.1.1.12
The source MAC address filter type for matching the QCL. The possible values are: any: No source MAC address filter is specified. (source MAC address filter status is 'don't-care'.) specific: choose this value to filter a specific source MAC address value with this QCL.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER any(1), specific(2)  

tnQosExtQclSMac 1.3.6.1.4.1.868.2.5.9.1.4.1.1.13
The source MAC address filter for matching the QCL. In S3280 implement, only MAC OUI(first three octets) are used for MAC address matching process.
Status: current Access: read-create
OBJECT-TYPE    
  MacAddress  

tnQosExtQclDMacType 1.3.6.1.4.1.868.2.5.9.1.4.1.1.14
The destination MAC address filter for matching the QCL. The possible values are: any: No destination MAC address filter is specified. (destination MAC address filter status is 'don't-care'.) unicast: Match the unicast destination MAC address for the QCL. multicast: Match the multicast destination MAC address for the QCL. broadcast: Match the broadcast destination MAC address for the QCL.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER any(1), unicast(2), multicast(3), broadcast(4)  

tnQosExtQclFrameType 1.3.6.1.4.1.868.2.5.9.1.4.1.1.15
The frame type for the QCL. The possible values are: any: The QCL will match any frame type. ethernet: The QCL will match Ethernet frame type. llc: The QCL will match LLC frame type. snap: The QCL will match SNAP frame type. ipv4: The QCL will match IPv4 frames. ipv6: The QCL will match IPv6 frames.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER any(1), ethernet(2), llc(3), snap(4), ipv4(5), ipv6(6)  

tnQosExtQclActClassDefault 1.3.6.1.4.1.868.2.5.9.1.4.1.1.16
Determe the type of matched frame traffic class modification. default: QCL do not change the traffic class of the matched received frames. specific: QCL will change the traffic class to the specific value of the matched received frames.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER default(1), specific(2)  

tnQosExtQclActClass 1.3.6.1.4.1.868.2.5.9.1.4.1.1.17
If a frame matches the QCE it will be put in the queue. It is only significant if tnQosExtQclActClassDefault is selected 'specific' value. tnQosExtQclActClass is a number in the range (0..(dot1dPortNumTrafficClasses-1)).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

tnQosExtQclActDplDefault 1.3.6.1.4.1.868.2.5.9.1.4.1.1.18
Determe the type of matched frame traffic DP (Drop Precedence) level modification. default: QCL do not change the DP (Drop Precedence) level of the matched received frames. specific: QCL will change the DP (Drop Precedence) level to the specific value of the matched received frames.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER default(1), specific(2)  

tnQosExtQclActDpl 1.3.6.1.4.1.868.2.5.9.1.4.1.1.19
If a frame matches the QCE then DP level will set to the value. It is only significant if tnQosExtQclActDplDefault is selected 'specific' value.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

tnQosExtQclActDscpDefault 1.3.6.1.4.1.868.2.5.9.1.4.1.1.20
Determe the type of matched frame DSCP modification. default: QCL do not change the DSCP of the matched received frames. specific: QCL will change the DSCP to the specific value of the matched received frames.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER default(1), specific(2)  

tnQosExtQclActDscp 1.3.6.1.4.1.868.2.5.9.1.4.1.1.21
If a frame matches the QCE then DSCP will be classified with the value. It is only significant if tnQosExtQclActDscpDefault is selected 'specific' value.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..63  

tnQosExtQclConflict 1.3.6.1.4.1.868.2.5.9.1.4.1.1.22
QCE status. It may be that resources required to add a QCE may not be available; in that case it shows conflict status as 'yes', otherwise it is always 'no'.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

tnQosExtQclStatus 1.3.6.1.4.1.868.2.5.9.1.4.1.1.23
The status of this conceptual row entry of QCL table. This object isused to manage the creation and deletion of conceptual rows. The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. For a detailed description of this object, please refer to SNMPv2-TC MIB.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

tnQosExtQclL2Table 1.3.6.1.4.1.868.2.5.9.1.4.2
A table used to configure the QoS Control List layer 2 frame settings.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TnQosExtQclL2Entry

tnQosExtQclL2Entry 1.3.6.1.4.1.868.2.5.9.1.4.2.1
An entry in the table used to configure the QoS Control List layer 2 fram settings.
Status: current Access: not-accessible
OBJECT-TYPE    
  TnQosExtQclL2Entry  

tnQosExtQclEtherType 1.3.6.1.4.1.868.2.5.9.1.4.2.1.1
The Ether type filter for matching the QCL. It is only significant if tnQosExtQclFrameType 'ethernet' is selected. The possible values are: any: No Ether type filter is specified. (Ether type filter status is 'don't-care'.) specific: Choose this value to filter a specific Ether type value with this QCL.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER any(1), specific(2)  

tnQosExtQclEtherVal 1.3.6.1.4.1.868.2.5.9.1.4.2.1.2
When tnQosExtQclEtherType is selected 'Specific' value, you can enter a specific value. The allowed value is from 0x0600 through 0xFFFF. If implement supports ipv4 or ipv6 selection in tnQosExtQclFrameType, the value 0x0800(ipv4) or 0x86DD(ipv6) are reserved from setting.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1536..65535  

tnQosExtQclLlcSsapType 1.3.6.1.4.1.868.2.5.9.1.4.2.1.3
The LLC SSAP type filter for matching the QCL. It is only significant if tnQosExtQclFrameType 'llc' is selected. The possible values are: any: No SSAP type filter is specified. (SSAP type filter status is 'don't-care'.) specific: Choose this value to filter a specific SSAP type value with this QCL.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER any(1), specific(2)  

tnQosExtQclLlcSsapVal 1.3.6.1.4.1.868.2.5.9.1.4.2.1.4
When tnQosExtQclLlcSsapType is selected 'Specific' value, you can enter a specific value. The allowed value is from 0 through 255.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

tnQosExtQclLlcDsapType 1.3.6.1.4.1.868.2.5.9.1.4.2.1.5
The LLC DSAP type filter for matching the QCL. It is only significant if tnQosExtQclFrameType 'llc' is selected. The possible values are: any: No DSAP type filter is specified. (DSAP type filter status is 'don't-care'.) specific: Choose this value to filter a specific DSAP type value with this QCL.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER any(1), specific(2)  

tnQosExtQclLlcDsapVal 1.3.6.1.4.1.868.2.5.9.1.4.2.1.6
When tnQosExtQclLlcDsapType is selected 'Specific' value, you can enter a specific value. The allowed value is from 0 through 255.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

tnQosExtQclLlcControlType 1.3.6.1.4.1.868.2.5.9.1.4.2.1.7
The LLC Control type filter for matching the QCL. It is only significant if tnQosExtQclFrameType 'llc' is selected. The possible values are: any: No Control type filter is specified. (Control type filter status is 'don't-care'.) specific: Choose this value to filter a specific Control type value with this QCL.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER any(1), specific(2)  

tnQosExtQclLlcControlVal 1.3.6.1.4.1.868.2.5.9.1.4.2.1.8
When tnQosExtQclLlcControlType is selected 'Specific' value, you can enter a specific value. The allowed value is from 0 through 255.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

tnQosExtQclSnapPidType 1.3.6.1.4.1.868.2.5.9.1.4.2.1.9
The SNAP PID type filter for matching the QCL. It is only significant if tnQosExtQclFrameType 'snap' is selected. The possible values are: any: No SNAP PIDtype filter is specified. (SNAP PID type filter status is 'don't-care'.) specific: Choose this value to filter a specific SNAP PID type value with this QCL.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER any(1), specific(2)  

tnQosExtQclSnapPidVal 1.3.6.1.4.1.868.2.5.9.1.4.2.1.10
When tnQosExtQclSnapPidType is selected 'Specific' value, you can enter a specific value. The allowed value is from 0x600 through 0xFFFF. If implement supports ipv4 or ipv6 selection in tnQosExtQclFrameType, the value 0x0800(ipv4) or 0x86DD(ipv6) are reserved from setting.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1536..65535  

tnQosExtQclIpTable 1.3.6.1.4.1.868.2.5.9.1.4.3
A table used to configure the QoS Control List IP settings.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TnQosExtQclIpEntry

tnQosExtQclIpEntry 1.3.6.1.4.1.868.2.5.9.1.4.3.1
An entry in the table used to configure the QoS Control List IP settings.
Status: current Access: not-accessible
OBJECT-TYPE    
  TnQosExtQclIpEntry  

tnQosExtQclProtoType 1.3.6.1.4.1.868.2.5.9.1.4.3.1.1
The IP protocol for matching the QCL.The possible values are: any: No protocol filter is specified. (Protocol filter status is 'don't-care'.) udp: Specify the UDP for matching the QCL. tcp: Specify the TCP for matching the QCL. specific: Choose this value to filter a specific protocol value with this QCL.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER any(1), udp(2), tcp(3), specific(4)  

tnQosExtQclProtoVal 1.3.6.1.4.1.868.2.5.9.1.4.3.1.2
When tnQosExtQclProtoType is selected 'Specific' value, you can enter a specific value. The allowed value is from 0 through 255. If implement supports udp or tcp selection in tnQosExtQclProtoType, the value 6(tcp) or 17(udp) are reserved from setting.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

tnQosExtQclDscpType 1.3.6.1.4.1.868.2.5.9.1.4.3.1.3
The DSCP filter for matching the QCL. The possible values are: any: No DSCP filter is specified. (DSCP filter status is 'don't-care'.) specific: choose this value to filter a specific DSCP value with this QCL. range: Choose this value to filter a specific DSCP range filter with this QCL.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER any(1), specific(2), range(3)  

tnQosExtQclDscpVal 1.3.6.1.4.1.868.2.5.9.1.4.3.1.4
When tnQosExtQclDscpType is selected 'Specific' value, you can enter a specific value. The allowed value is from 0 through 63.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..63  

tnQosExtQclDscpMin 1.3.6.1.4.1.868.2.5.9.1.4.3.1.5
When tnQosExtQclDscpType is selected 'Range' value, you can enter a specific range. this value should be lower than tnQosExtQclDscpMax value. The allowed range start is from 0 through 63.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..63  

tnQosExtQclDscpMax 1.3.6.1.4.1.868.2.5.9.1.4.3.1.6
When tnQosExtQclDscpType is selected 'Range' value, you can enter a specific range. this value should be higher than tnQosExtQclDscpMin value. The allowed range end is from 0 through 63.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..63  

tnQosExtQclSrcIpType 1.3.6.1.4.1.868.2.5.9.1.4.3.1.7
The source IP address type filter for matching the QCL. The possible values are: any: No source IP address filter is specified. (source IP address filter status is 'don't-care'.) specific: Choose this value to filter a specific source IP address with this QCL.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER any(1), specific(2)  

tnQosExtQclSrcIpAddrType 1.3.6.1.4.1.868.2.5.9.1.4.3.1.8
Specify the tnQosExtQclSrcIpAddr type.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddressType  

tnQosExtQclSrcIpAddr 1.3.6.1.4.1.868.2.5.9.1.4.3.1.9
When tnQosExtQclSrcIpType is selected 'Specific' value, you can enter a specific host or network address.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddress  

tnQosExtQclSrcIpMaskType 1.3.6.1.4.1.868.2.5.9.1.4.3.1.10
Specify the tnQosExtQclSrcIpMask type.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddressType  

tnQosExtQclSrcIpMask 1.3.6.1.4.1.868.2.5.9.1.4.3.1.11
When tnQosExtQclSrcIpType is selected 'Specific' value, you can enter a specific network mask for the source IP address.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddress  

tnQosExtQclIpv4Fragment 1.3.6.1.4.1.868.2.5.9.1.4.3.1.12
The IPv4 Fragment for matching the QCL. This involves the settings for the More Fragments (MF) bit and the Fragment Offset (FRAG OFFSET) field for an IPv4 frame. The possible values are: any: The QCL will match any MF bit. fragment: IPv4 frames where the MF bit is set or the FRAG OFFSET field is greater than zero must be able to match this entry. nonfragment: IPv4 frames where the MF bit is set or the FRAG OFFSET field is greater than zero must not be able to match this entry.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER any(1), fragment(2), nonfragment(3)  

tnQosExtQclTcpUdpSportType 1.3.6.1.4.1.868.2.5.9.1.4.3.1.13
The TCP/UDP source port for matching the QCL. It is only significant if protocol filter 'UDP' or 'TCP' is selected. The possible values are: any: No TCP/UDP source port filter is specified. (Source port filter status is 'don't-care'.) specific: Choose this value to filter a specific TCP/UDP source port No. with this QCL. range: Choose this value to filter a specific TCP/UDP source port range filter with this QCL.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER any(1), specific(2), range(3)  

tnQosExtQclTcpUdpSportVal 1.3.6.1.4.1.868.2.5.9.1.4.3.1.14
When tnQosExtQclTcpUdpSportType is selected 'Specific' value, you can enter a specific value. The allowed value is from 0 through 65535.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

tnQosExtQclTcpUdpSportMin 1.3.6.1.4.1.868.2.5.9.1.4.3.1.15
When tnQosExtQclTcpUdpSportType is selected 'Range' value, you can enter a specific range. this value should be lower than tnQosExtQclTcpUdpSportMax value. The allowed range start is from 0 through 65535.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

tnQosExtQclTcpUdpSportMax 1.3.6.1.4.1.868.2.5.9.1.4.3.1.16
When tnQosExtQclTcpUdpSportType is selected 'Range' value, you can enter a specific range. this value should be higher than tnQosExtQclTcpUdpSportMin value. The allowed range end is from 0 through 65535.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

tnQosExtQclTcpUdpDportType 1.3.6.1.4.1.868.2.5.9.1.4.3.1.17
The TCP/UDP destination port for matching the QCL. It only significant if protocol filter 'UDP' or 'TCP' is selected. The possible values are: any: No TCP/UDP destination port filter is specified. (Source port filter status is 'don't-care'.) specific: Choose this value to filter a specific TCP/UDP source port No. with this QCL. range: Choose this value to filter a specific TCP/UDP source port range filter with this QCL.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER any(1), specific(2), range(3)  

tnQosExtQclTcpUdpDportVal 1.3.6.1.4.1.868.2.5.9.1.4.3.1.18
When tnQosExtQclTcpUdpDportVal is selected 'Specific' value, you can enter a specific value. The allowed value is from 0 through 65535.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

tnQosExtQclTcpUdpDportMin 1.3.6.1.4.1.868.2.5.9.1.4.3.1.19
When tnQosExtQclTcpUdpDportVal is selected 'Range' value, you can enter a specific range. this value should be lower than tnQosExtQclTcpUdpDportMax value. The allowed range start is from 0 through 65535.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

tnQosExtQclTcpUdpDportMax 1.3.6.1.4.1.868.2.5.9.1.4.3.1.20
When tnQosExtQclTcpUdpDportVal is selected 'Range' value, you can enter a specific range. this value should be higher than tnQosExtQclTcpUdpDportMin value. The allowed range end is from 0 through 65535.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor