TELDAT-MON-INTERF-FR-MIB

File: TELDAT-MON-INTERF-FR-MIB.mib (81675 bytes)

Imported modules

RFC1155-SMI RFC-1212 RFC1213-MIB
TELDAT-SW-STRUCTURE-MIB

Imported symbols

IpAddress Counter OBJECT-TYPE
DisplayString telProdNpMonInterfRouter

Defined Types

TelProdNpMonInterfFRGlobalEntry  
SEQUENCE    
  telProdNpMonInterfFRGloIndex INTEGER
  telProdNpMonInterfFRGloDriverType DisplayString
  telProdNpMonInterfFRGloLineSpeed INTEGER
  telProdNpMonInterfFRGloLastResetWeek INTEGER
  telProdNpMonInterfFRGloLastResetDay INTEGER
  telProdNpMonInterfFRGloLastResetHour INTEGER
  telProdNpMonInterfFRGloLastResetMin INTEGER
  telProdNpMonInterfFRGloLastResetSec INTEGER

TelProdNpMonInterfFRRS232Entry  
SEQUENCE    
  telProdNpMonInterfFRRS232Index INTEGER
  telProdNpMonInterfFRRS232CircIndex INTEGER
  telProdNpMonInterfFRRS232Circuit INTEGER
  telProdNpMonInterfFRRS232Nickname DisplayString
  telProdNpMonInterfFRRS232State DisplayString

TelProdNpMonInterfFRFramesEntry  
SEQUENCE    
  telProdNpMonInterfFRFramesIndex INTEGER
  telProdNpMonInterfFRFramesClear INTEGER
  telProdNpMonInterfFRFramesCRCError Counter
  telProdNpMonInterfFRFramesMissed Counter
  telProdNpMonInterfFRFramesAborted Counter
  telProdNpMonInterfFRFramesAlignment Counter
  telProdNpMonInterfFRFramesTooLong Counter
  telProdNpMonInterfFRFramesOverrun Counter
  telProdNpMonInterfFRFramesUnderrun Counter
  telProdNpMonInterfFRFramesTxAbort Counter

TelProdNpMonInterfFRCompStatEntry  
SEQUENCE    
  telProdNpMonInterfFRCStatIfcIndex INTEGER
  telProdNpMonInterfFRCStatDlciIndex INTEGER
  telProdNpMonInterfFRCStatClear INTEGER
  telProdNpMonInterfFRCStatManFrComp Counter
  telProdNpMonInterfFRCStatManByComp Counter
  telProdNpMonInterfFRCStatProcFrComp Counter
  telProdNpMonInterfFRCStatProcByComp Counter
  telProdNpMonInterfFRCStatNotProcFrComp Counter
  telProdNpMonInterfFRCStatNotProcByComp Counter
  telProdNpMonInterfFRCStatErrorFrComp Counter
  telProdNpMonInterfFRCStatOutSeqFrComp Counter
  telProdNpMonInterfFRCStatManFrDecomp Counter
  telProdNpMonInterfFRCStatManByDecomp Counter
  telProdNpMonInterfFRCStatProcFrDecomp Counter
  telProdNpMonInterfFRCStatProcByDecomp Counter
  telProdNpMonInterfFRCStatNotProcFrDecomp Counter
  telProdNpMonInterfFRCStatNotProcByDecomp Counter
  telProdNpMonInterfFRCStatErrorFrDecomp Counter
  telProdNpMonInterfFRCStatOutSeqFrDecomp Counter

TelProdNpMonInterfFRCStatBeginEntry  
SEQUENCE    
  telProdNpMonInterfFRCStatBeginInterfIndex INTEGER
  telProdNpMonInterfFRCStatBeginDay INTEGER
  telProdNpMonInterfFRCStatBeginMonth INTEGER
  telProdNpMonInterfFRCStatBeginYear INTEGER
  telProdNpMonInterfFRCStatBeginHour INTEGER
  telProdNpMonInterfFRCStatBeginMin INTEGER
  telProdNpMonInterfFRCStatBeginSec INTEGER

TelProdNpMonInterfFRCrtpEntry  
SEQUENCE    
  telProdNpMonInterfFRCrtpIfcIndex INTEGER
  telProdNpMonInterfFRCrtpDlciIndex INTEGER
  telProdNpMonInterfFRCrtpClear INTEGER
  telProdNpMonInterfFRCrtpOutRTPPack Counter
  telProdNpMonInterfFRCrtpOutRTPComp Counter
  telProdNpMonInterfFRCrtpSearchConn Counter
  telProdNpMonInterfFRCrtpNoFindConn Counter
  telProdNpMonInterfFRCrtpInRTPunCom Counter
  telProdNpMonInterfFRCrtpInRTPComp Counter
  telProdNpMonInterfFRCrtpInUnknownType Counter
  telProdNpMonInterfFRCrtpContexStatePack Counter

TelProdNpMonInterfFRLmiEntry  
SEQUENCE    
  telProdNpMonInterfFRLmiIndex INTEGER
  telProdNpMonInterfFRLmiClearStat INTEGER
  telProdNpMonInterfFRLmiHab INTEGER
  telProdNpMonInterfFRLmiDlci INTEGER
  telProdNpMonInterfFRLmiType INTEGER
  telProdNpMonInterfFRLmiOrphans INTEGER
  telProdNpMonInterfFRLmiSecInterv INTEGER
  telProdNpMonInterfFRLmiLineAccRate INTEGER
  telProdNpMonInterfFRLmiMTU INTEGER
  telProdNpMonInterfFRLmiCIRAdjust INTEGER
  telProdNpMonInterfFRLmiT1 INTEGER
  telProdNpMonInterfFRLmiN1 INTEGER
  telProdNpMonInterfFRLmiN2 INTEGER
  telProdNpMonInterfFRLmiN3 INTEGER
  telProdNpMonInterfFRLmiIRIncr INTEGER
  telProdNpMonInterfFRLmiIRDecr INTEGER
  telProdNpMonInterfFRLmiIRMin INTEGER
  telProdNpMonInterfFRLmiPTPLine INTEGER
  telProdNpMonInterfFRLmiPTPDlci INTEGER
  telProdNpMonInterfFRLmiProtBroad INTEGER
  telProdNpMonInterfFRLmiEmuMulticast INTEGER
  telProdNpMonInterfFRLmiCongMonit INTEGER
  telProdNpMonInterfFRLmiCIRMonit INTEGER
  telProdNpMonInterfFRLmiEnabPVCBkupRetTime INTEGER
  telProdNpMonInterfFRLmiCurrentRcvSeq INTEGER
  telProdNpMonInterfFRLmiCurrentTxSeq INTEGER
  telProdNpMonInterfFRLmiTotStatusEnq Counter
  telProdNpMonInterfFRLmiTotStatusResp Counter
  telProdNpMonInterfFRLmiTotSeqReq Counter
  telProdNpMonInterfFRLmiTotSeqResp Counter

TelProdNpMonInterfFRPvcStatusEntry  
SEQUENCE    
  telProdNpMonInterfFRPvcStaIfcIndex INTEGER
  telProdNpMonInterfFRPvcStaClear INTEGER
  telProdNpMonInterfFRPvcStaTotAllow INTEGER
  telProdNpMonInterfFRPvcStaTotConfig INTEGER
  telProdNpMonInterfFRPvcStaTotActiv INTEGER
  telProdNpMonInterfFRPvcStaTotCong INTEGER
  telProdNpMonInterfFRPvcStaTotLeftNet INTEGER
  telProdNpMonInterfFRPvcStaTotJoinNet INTEGER

TelProdNpMonInterfFRPvcEntry  
SEQUENCE    
  telProdNpMonInterfFRPvcIfcIndex INTEGER
  telProdNpMonInterfFRPvcDlciIndex INTEGER
  telProdNpMonInterfFRPvcClearStatistics INTEGER
  telProdNpMonInterfFRPvcName DisplayString
  telProdNpMonInterfFRPvcCircStatus INTEGER
  telProdNpMonInterfFRPvcCircType INTEGER
  telProdNpMonInterfFRPvcOrphan INTEGER
  telProdNpMonInterfFRPvcEncrypt INTEGER
  telProdNpMonInterfFRPvcTxFrames INTEGER
  telProdNpMonInterfFRPvcTxBytes INTEGER
  telProdNpMonInterfFRPvcRcvFrames INTEGER
  telProdNpMonInterfFRPvcRcvBytes INTEGER
  telProdNpMonInterfFRPvcQueueOverf INTEGER
  telProdNpMonInterfFRPvcOverrun INTEGER
  telProdNpMonInterfFRPvcTotFECNs INTEGER
  telProdNpMonInterfFRPvcTotBECNs INTEGER
  telProdNpMonInterfFRPvcTimesCong INTEGER
  telProdNpMonInterfFRPvcTimesInact INTEGER
  telProdNpMonInterfFRPvcCIR INTEGER
  telProdNpMonInterfFRPvcVIR INTEGER
  telProdNpMonInterfFRPvcBc INTEGER
  telProdNpMonInterfFRPvcBe INTEGER

TelProdNpMonInterfFRProtAddEntry  
SEQUENCE    
  telProdNpMonInterfFRProtAddIfcIndex INTEGER
  telProdNpMonInterfFRProtAddProtocIndex INTEGER
  telProdNpMonInterfFRProtAddOrdenIndex INTEGER
  telProdNpMonInterfFRProtAddAddress IpAddress
  telProdNpMonInterfFRProtAddDlci INTEGER

TelProdNpMonInterfFRActCallsEntry  
SEQUENCE    
  telProdNpMonInterfFRActCallsIfcIndex INTEGER
  telProdNpMonInterfFRActCallsOrdenIndex INTEGER
  telProdNpMonInterfFRActCallsCircuitName DisplayString
  telProdNpMonInterfFRActCallsDlci INTEGER
  telProdNpMonInterfFRActCallsCalledNum DisplayString
  telProdNpMonInterfFRActCallsCallingNum DisplayString
  telProdNpMonInterfFRActCallsRef INTEGER
  telProdNpMonInterfFRActCallsStartHour INTEGER
  telProdNpMonInterfFRActCallsStartMin INTEGER
  telProdNpMonInterfFRActCallsStartSec INTEGER

TelProdNpMonInterfFRRelCallsEntry  
SEQUENCE    
  telProdNpMonInterfFRRelCallsIndex INTEGER
  telProdNpMonInterfFRRelCallsOrdenIndex INTEGER
  telProdNpMonInterfFRRelCallsClear INTEGER
  telProdNpMonInterfFRRelCallsCircName DisplayString
  telProdNpMonInterfFRRelCallsDlci INTEGER
  telProdNpMonInterfFRRelCallsCalledNum DisplayString
  telProdNpMonInterfFRRelCallsCallingNum DisplayString
  telProdNpMonInterfFRRelCallsCL INTEGER
  telProdNpMonInterfFRRelCallsDL INTEGER
  telProdNpMonInterfFRRelCallsStartHour INTEGER
  telProdNpMonInterfFRRelCallsStartMin INTEGER
  telProdNpMonInterfFRRelCallsStartSec INTEGER
  telProdNpMonInterfFRRelCallsEndHour INTEGER
  telProdNpMonInterfFRRelCallsEndMin INTEGER
  telProdNpMonInterfFRRelCallsEndSec INTEGER

Defined Values

telProdNpMonInterfFR 1.3.6.1.4.1.2007.4.1.2.2.2.9
OBJECT IDENTIFIER    

telProdNpMonInterfFRGlobalTable 1.3.6.1.4.1.2007.4.1.2.2.2.9.1
Table of general information about interfaces Frame Relay. This information is not available for FR-Dial or FR over RDSI interfaces. The entry number is determined by the interface value.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TelProdNpMonInterfFRGlobalEntry

telProdNpMonInterfFRGlobalEntry 1.3.6.1.4.1.2007.4.1.2.2.2.9.1.1
Each entry consists of the interface number of the node, that is the table index, the interface type or physical driver (DTE o DCE) used by Frame Relay, the line speed and the time the last port reset was performed.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  TelProdNpMonInterfFRGlobalEntry  

telProdNpMonInterfFRGloIndex 1.3.6.1.4.1.2007.4.1.2.2.2.9.1.1.1
Node interface number, that indicates the table entry (table index).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRGloDriverType 1.3.6.1.4.1.2007.4.1.2.2.2.9.1.1.2
FR interface type: (1) DCE, (2) DTE.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

telProdNpMonInterfFRGloLineSpeed 1.3.6.1.4.1.2007.4.1.2.2.2.9.1.1.3
Line data rate, expressed in bits per second. The value 0 indicates unknown speed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRGloLastResetWeek 1.3.6.1.4.1.2007.4.1.2.2.2.9.1.1.4
Weeks passed since the last port reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRGloLastResetDay 1.3.6.1.4.1.2007.4.1.2.2.2.9.1.1.5
Days passed since the last port reset: spare days after counting weeks, that do not form a complete week, that means the variable value will be always lower than 7.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRGloLastResetHour 1.3.6.1.4.1.2007.4.1.2.2.2.9.1.1.6
Hours passed since the last port reset. If more than a week has passed, this variable indicates the number hours to add to the number of weeks and days, and its value will be lower than 24 so a complete day can't be formed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRGloLastResetMin 1.3.6.1.4.1.2007.4.1.2.2.2.9.1.1.7
Minutes passed since the last port reset. This variable indicates the number of minutes since the last hour was added to the hour counter.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRGloLastResetSec 1.3.6.1.4.1.2007.4.1.2.2.2.9.1.1.8
Seconds passed since the last port reset. The total time passed will be the addition of weeks, days, hours, minutes and seconds since the last reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRRS232Table 1.3.6.1.4.1.2007.4.1.2.2.2.9.2
Table of RS232 signals or circuits. It shows if the corresponding signal is active. This table does not exist for FR-Dial or FR over ISDN interfaces. The entry number is determined by the interface value.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TelProdNpMonInterfFRRS232Entry

telProdNpMonInterfFRRS232Entry 1.3.6.1.4.1.2007.4.1.2.2.2.9.2.1
Each entry consists of the node interface number, that is the table index, the order number of the circuit in that interface (second index), that goes between 1 and a maximum number that depends on the connector type (maximum 7), the circuit number (105, 106, 107, 108, 109, 125, 141), its name (RTS, CTS, DSR, DTR, DCD, RI, LL) and if it is active or not.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  TelProdNpMonInterfFRRS232Entry  

telProdNpMonInterfFRRS232Index 1.3.6.1.4.1.2007.4.1.2.2.2.9.2.1.1
Node interface number. It is the first table index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRRS232CircIndex 1.3.6.1.4.1.2007.4.1.2.2.2.9.2.1.2
Second table index. It is a number that goes between 1 and the maximum number of this type of circuits, that varies with the connector.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..7  

telProdNpMonInterfFRRS232Circuit 1.3.6.1.4.1.2007.4.1.2.2.2.9.2.1.3
RS232 circuit number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 105..141  

telProdNpMonInterfFRRS232Nickname 1.3.6.1.4.1.2007.4.1.2.2.2.9.2.1.4
Circuit name.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

telProdNpMonInterfFRRS232State 1.3.6.1.4.1.2007.4.1.2.2.2.9.2.1.5
Signal (of the circuits) status: on, off or unknown.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

telProdNpMonInterfFRFramesTable 1.3.6.1.4.1.2007.4.1.2.2.2.9.3
Table of counters of output frames and errors on input frames. This information is not available for FR-Dial or FR over ISDN interfaces. The entry number is determined by the interface (table index).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TelProdNpMonInterfFRFramesEntry

telProdNpMonInterfFRFramesEntry 1.3.6.1.4.1.2007.4.1.2.2.2.9.3.1
Each entry consists of the node interface number, which is the table index, a variable that shows the output of the last table delete attempt (get operation) or performs the delete operation (set operation), CRC errors in incoming frames, alignment errors, lost incoming frames due to overrun, too long frames, aborted frames, number of errors due to DMA/FIFO overrun, number of DMA/FIFO underrun in outgoing frames and aborted outputs sent.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  TelProdNpMonInterfFRFramesEntry  

telProdNpMonInterfFRFramesIndex 1.3.6.1.4.1.2007.4.1.2.2.2.9.3.1.1
Node interface number, which shows the corresponding table entry (it is the table index).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRFramesClear 1.3.6.1.4.1.2007.4.1.2.2.2.9.3.1.2
This variable when is read shows the output from the last table delete attempt: the value is 2 if the deletion was performed succesfully, 3 if an error ocurred and 4 for an undefined result, that means that nobody has tried to delete the table yet. In set operations, the value 1 (it is the only value that can be assigned by a writing operation) causes a table deletion: frame counters are set to 0.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER delete(1), ok(2), error(3), undefined(4)  

telProdNpMonInterfFRFramesCRCError 1.3.6.1.4.1.2007.4.1.2.2.2.9.3.1.3
Number of frames with CRC errors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

telProdNpMonInterfFRFramesMissed 1.3.6.1.4.1.2007.4.1.2.2.2.9.3.1.4
Number of incoming frames lost due to overrun.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

telProdNpMonInterfFRFramesAborted 1.3.6.1.4.1.2007.4.1.2.2.2.9.3.1.5
Number of incoming frames aborted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

telProdNpMonInterfFRFramesAlignment 1.3.6.1.4.1.2007.4.1.2.2.2.9.3.1.6
Number of incoming frames with alignment errors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

telProdNpMonInterfFRFramesTooLong 1.3.6.1.4.1.2007.4.1.2.2.2.9.3.1.7
Number of too long incoming frames.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

telProdNpMonInterfFRFramesOverrun 1.3.6.1.4.1.2007.4.1.2.2.2.9.3.1.8
Number of DMA/FIFO overrun.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

telProdNpMonInterfFRFramesUnderrun 1.3.6.1.4.1.2007.4.1.2.2.2.9.3.1.9
Number of DMA/FIFO overrun.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

telProdNpMonInterfFRFramesTxAbort 1.3.6.1.4.1.2007.4.1.2.2.2.9.3.1.10
Number of aborted outputs sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

telProdNpMonInterfFRCompGroup 1.3.6.1.4.1.2007.4.1.2.2.2.9.4
OBJECT IDENTIFIER    

telProdNpMonInterfFRCompStatTable 1.3.6.1.4.1.2007.4.1.2.2.2.9.4.1
This table contains compression statistics of Frame Relay, FR-Dial and FR over ISDN interfaces. The entry number is determined by the interface value (first table index) and the dlci number whose statistics want to be got (second table index).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TelProdNpMonInterfFRCompStatEntry

telProdNpMonInterfFRCompStatEntry 1.3.6.1.4.1.2007.4.1.2.2.2.9.4.1.1
Each entry consists of the interface number, which is the first table index, the dlci number whose statistics are of interest (second index), a variable that shows the output of the last table delete attempt (get operation) or performs the delete operation (set operation), and the current output from managed, processed and non processed bytes and frames counters, error frames counters and out of sequence in compression and decompression frames counter.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  TelProdNpMonInterfFRCompStatEntry  

telProdNpMonInterfFRCStatIfcIndex 1.3.6.1.4.1.2007.4.1.2.2.2.9.4.1.1.1
Node interface number. It is the first table index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRCStatDlciIndex 1.3.6.1.4.1.2007.4.1.2.2.2.9.4.1.1.2
Dlci number in the interface. It is the second table index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRCStatClear 1.3.6.1.4.1.2007.4.1.2.2.2.9.4.1.1.3
This variable when is read shows the output from the last table delete attempt: the value is 2 if the deletion was performed succesfully, 3 if an error ocurred and 4 for an undefined result, that means that nobody has tried to delete the table yet. In set operations, the value 1 (it is the only value that can be assigned by a writing operation) causes a table deletion: frame counters are set to 0.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER delete(1), ok(2), error(3), undefined(4)  

telProdNpMonInterfFRCStatManFrComp 1.3.6.1.4.1.2007.4.1.2.2.2.9.4.1.1.4
Number of frames managed in compression.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

telProdNpMonInterfFRCStatManByComp 1.3.6.1.4.1.2007.4.1.2.2.2.9.4.1.1.5
Number of bytes managed in compression.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

telProdNpMonInterfFRCStatProcFrComp 1.3.6.1.4.1.2007.4.1.2.2.2.9.4.1.1.6
Number of frames processed in compression.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

telProdNpMonInterfFRCStatProcByComp 1.3.6.1.4.1.2007.4.1.2.2.2.9.4.1.1.7
Number of bytes processed in compression.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

telProdNpMonInterfFRCStatNotProcFrComp 1.3.6.1.4.1.2007.4.1.2.2.2.9.4.1.1.8
Number of frames not processed in compression.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

telProdNpMonInterfFRCStatNotProcByComp 1.3.6.1.4.1.2007.4.1.2.2.2.9.4.1.1.9
Number of bytes not processed in compression.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

telProdNpMonInterfFRCStatErrorFrComp 1.3.6.1.4.1.2007.4.1.2.2.2.9.4.1.1.10
Number of frames with errors in compression.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

telProdNpMonInterfFRCStatOutSeqFrComp 1.3.6.1.4.1.2007.4.1.2.2.2.9.4.1.1.11
Number of frames out of sequence in compression.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

telProdNpMonInterfFRCStatManFrDecomp 1.3.6.1.4.1.2007.4.1.2.2.2.9.4.1.1.12
Number of frames managed in decompression.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

telProdNpMonInterfFRCStatManByDecomp 1.3.6.1.4.1.2007.4.1.2.2.2.9.4.1.1.13
Number of bytes managed in decompression.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

telProdNpMonInterfFRCStatProcFrDecomp 1.3.6.1.4.1.2007.4.1.2.2.2.9.4.1.1.14
Number of frames processed in decompression.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

telProdNpMonInterfFRCStatProcByDecomp 1.3.6.1.4.1.2007.4.1.2.2.2.9.4.1.1.15
Number of bytes processed in decompression.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

telProdNpMonInterfFRCStatNotProcFrDecomp 1.3.6.1.4.1.2007.4.1.2.2.2.9.4.1.1.16
Number of frames not processed in decompression.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

telProdNpMonInterfFRCStatNotProcByDecomp 1.3.6.1.4.1.2007.4.1.2.2.2.9.4.1.1.17
Number of bytes not processed in decompression.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

telProdNpMonInterfFRCStatErrorFrDecomp 1.3.6.1.4.1.2007.4.1.2.2.2.9.4.1.1.18
Number of frames with errors in decompression.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

telProdNpMonInterfFRCStatOutSeqFrDecomp 1.3.6.1.4.1.2007.4.1.2.2.2.9.4.1.1.19
Number of frames out of sequence in decompression.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

telProdNpMonInterfFRCStatBeginTable 1.3.6.1.4.1.2007.4.1.2.2.2.9.4.2
This table contains compression statistics of Frame Relay, FR-Dial and FR over ISDN interfaces. The entry number is determined by the interface value (table index).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TelProdNpMonInterfFRCStatBeginEntry

telProdNpMonInterfFRCStatBeginEntry 1.3.6.1.4.1.2007.4.1.2.2.2.9.4.2.1
Each entry consists of the node interface number, that is the table index, and a variable for each component of the time and date when the statistic counting began.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  TelProdNpMonInterfFRCStatBeginEntry  

telProdNpMonInterfFRCStatBeginInterfIndex 1.3.6.1.4.1.2007.4.1.2.2.2.9.4.2.1.1
Node interface number, that indicates the table entry (table index).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRCStatBeginDay 1.3.6.1.4.1.2007.4.1.2.2.2.9.4.2.1.2
Beginning day of the counting of compression statistics.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRCStatBeginMonth 1.3.6.1.4.1.2007.4.1.2.2.2.9.4.2.1.3
Beginning month of the counting of compression statistics.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRCStatBeginYear 1.3.6.1.4.1.2007.4.1.2.2.2.9.4.2.1.4
Beginning year of the counting of compression statistics.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRCStatBeginHour 1.3.6.1.4.1.2007.4.1.2.2.2.9.4.2.1.5
Beginning hour of the counting of compression statistics.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRCStatBeginMin 1.3.6.1.4.1.2007.4.1.2.2.2.9.4.2.1.6
Beginning minute of the counting of compression statistics.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRCStatBeginSec 1.3.6.1.4.1.2007.4.1.2.2.2.9.4.2.1.7
Beginning second of the counting of compression statistics.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRCompVersGroup 1.3.6.1.4.1.2007.4.1.2.2.2.9.4.3
OBJECT IDENTIFIER    

telProdNpMonInterfFRCompVersRevision 1.3.6.1.4.1.2007.4.1.2.2.2.9.4.3.1
Revision.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

telProdNpMonInterfFRCompVersCard 1.3.6.1.4.1.2007.4.1.2.2.2.9.4.3.2
Card.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

telProdNpMonInterfFRCompVersInterruptMode 1.3.6.1.4.1.2007.4.1.2.2.2.9.4.3.3
It indicates if the Interruption Mode is active (1) or inactive (2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER active(1), inactive(2)  

telProdNpMonInterfFRCrtpTable 1.3.6.1.4.1.2007.4.1.2.2.2.9.5
Table of statistics of CRTP compression of Frame Relay, FR-Dial and FR over RDSI interfaces. The entry number is determined by the interface value (first table index) and the dlci number for the interface of which we want to obtain the statistics (second index).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TelProdNpMonInterfFRCrtpEntry

telProdNpMonInterfFRCrtpEntry 1.3.6.1.4.1.2007.4.1.2.2.2.9.5.1
Each entry consists of the node interface number, which is the table index, the dlci number for the interface of which we want to obtain the statistics (second index),a variable that shows the output of the last table delete attempt (get operation) or performs the delete operation (set operation), and the current output from the counters of outgoing detected RTP packets, outgoing compressed RTP packets, number of searchs of the connection status, number of times the connection status was not found, number of incoming non compressed RTP packets, number of incoming compressed RTP packets, number of incoming unknown RTP packets and number of Context State RTP packets.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  TelProdNpMonInterfFRCrtpEntry  

telProdNpMonInterfFRCrtpIfcIndex 1.3.6.1.4.1.2007.4.1.2.2.2.9.5.1.1
Node interface number. It is the first table index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRCrtpDlciIndex 1.3.6.1.4.1.2007.4.1.2.2.2.9.5.1.2
Dlci number of the interface. It is the second table index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRCrtpClear 1.3.6.1.4.1.2007.4.1.2.2.2.9.5.1.3
This variable when is read shows the output from the last table delete attempt: the value is 2 if the deletion was performed succesfully, 3 if an error ocurred and 4 for an undefined result, that means that nobody has tried to delete the table yet. In set operations, the value 1 (it is the only value that can be assigned by a writing operation) causes a table deletion: frame counters are set to 0.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER delete(1), ok(2), error(3), undefined(4)  

telProdNpMonInterfFRCrtpOutRTPPack 1.3.6.1.4.1.2007.4.1.2.2.2.9.5.1.4
Number of detected outgoing RTP packets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

telProdNpMonInterfFRCrtpOutRTPComp 1.3.6.1.4.1.2007.4.1.2.2.2.9.5.1.5
Number of compressed outgoing RTP packets
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

telProdNpMonInterfFRCrtpSearchConn 1.3.6.1.4.1.2007.4.1.2.2.2.9.5.1.6
Number of searchs of the connection status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

telProdNpMonInterfFRCrtpNoFindConn 1.3.6.1.4.1.2007.4.1.2.2.2.9.5.1.7
Number of times the connection status was not found.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

telProdNpMonInterfFRCrtpInRTPunCom 1.3.6.1.4.1.2007.4.1.2.2.2.9.5.1.8
Number of non compressed incoming RTP packets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

telProdNpMonInterfFRCrtpInRTPComp 1.3.6.1.4.1.2007.4.1.2.2.2.9.5.1.9
Number of compressed incoming RTP packets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

telProdNpMonInterfFRCrtpInUnknownType 1.3.6.1.4.1.2007.4.1.2.2.2.9.5.1.10
Number of unknown incoming RTP packets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

telProdNpMonInterfFRCrtpContexStatePack 1.3.6.1.4.1.2007.4.1.2.2.2.9.5.1.11
Number of Context State RTP packets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

telProdNpMonInterfFRLmiTable 1.3.6.1.4.1.2007.4.1.2.2.2.9.6
LMI table. The entry number is determined by the interface value.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TelProdNpMonInterfFRLmiEntry

telProdNpMonInterfFRLmiEntry 1.3.6.1.4.1.2007.4.1.2.2.2.9.6.1
Each entry consists of the node interface number, that is the table index, a variable that shows the output from the last statistics delete attempt, another variable shows if the LMI management is enabled, the dlci associated to that management, the LMI type, if orphan circuits are allowed, the LMI sequence interval (in seconds), line access rate (bps), the Interface MTU (Maximum Transmission Unit) (in bytes), CIR monitor adjustment, Timer T1 (in seconds), counter N1 increments, LMI N2 error threshold, LMI N3 error window, IR percentage increment, IR percentage decrement, point to point line enabled or not and the point to point DLCI used in this case, protocol broadcast enabled or not, emulate multicast enabled or not for the active PVCs, congestion monitoring enabled or not, CIR monitoring that limits the router transmission speed active or inactive, a variable used to enable the inmediate return of Frame Relay back-up that only allows set operations, number of received sequence, number of transmitted sequence, total number of link status requests and responses to these requests, total number of sequence requests and number of responses to sequence requests.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  TelProdNpMonInterfFRLmiEntry  

telProdNpMonInterfFRLmiIndex 1.3.6.1.4.1.2007.4.1.2.2.2.9.6.1.1
Node interface number, that shows the corresponding table entry (table index).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRLmiClearStat 1.3.6.1.4.1.2007.4.1.2.2.2.9.6.1.2
This variable when is read shows the output from the last table delete attempt: the value is 2 if the deletion was performed succesfully, 3 if an error ocurred and 4 for an undefined result, that means that nobody has tried to delete the table yet. In set operations, the value 1 (it is the only value that can be assigned by a writing operation) causes a table deletion: frame counters are set to 0.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER delete(1), ok(2), error(3), undefined(4)  

telProdNpMonInterfFRLmiHab 1.3.6.1.4.1.2007.4.1.2.2.2.9.6.1.3
LMI enabled or disabled: it shows if Frame Relay management is active (1) or inactive (2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

telProdNpMonInterfFRLmiDlci 1.3.6.1.4.1.2007.4.1.2.2.2.9.6.1.4
LMI DLCI: Management circuit number. It will be 0(ANSI, CCITT) or 1023(LMI).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRLmiType 1.3.6.1.4.1.2007.4.1.2.2.2.9.6.1.5
LMI Type: (1) CCITT, (2) ANSI T.1 617 Annex D, (3) LMI Rev.1. If LMI is not enabled this variable takes the value 0 (disabled-lmi).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled-lmi(0), ccitt(1), ansi(2), lmi(3)  

telProdNpMonInterfFRLmiOrphans 1.3.6.1.4.1.2007.4.1.2.2.2.9.6.1.6
Indicates if all non configured circuits made known by management are available for use, yes or no.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

telProdNpMonInterfFRLmiSecInterv 1.3.6.1.4.1.2007.4.1.2.2.2.9.6.1.7
Indicates the sequence interval that LMI management uses (in seconds).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRLmiLineAccRate 1.3.6.1.4.1.2007.4.1.2.2.2.9.6.1.8
Physical data rate of the Frame Relay interface in bits per second.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRLmiMTU 1.3.6.1.4.1.2007.4.1.2.2.2.9.6.1.9
MTU (maximum transmission unit) of the Frame Relay interface in bytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRLmiCIRAdjust 1.3.6.1.4.1.2007.4.1.2.2.2.9.6.1.10
CIR monitor adjustment.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRLmiT1 1.3.6.1.4.1.2007.4.1.2.2.2.9.6.1.11
Timer T1, in seconds.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 5..30  

telProdNpMonInterfFRLmiN1 1.3.6.1.4.1.2007.4.1.2.2.2.9.6.1.12
Counter N1 increments.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

telProdNpMonInterfFRLmiN2 1.3.6.1.4.1.2007.4.1.2.2.2.9.6.1.13
Allowable errors N2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..10  

telProdNpMonInterfFRLmiN3 1.3.6.1.4.1.2007.4.1.2.2.2.9.6.1.14
Error window N3.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..10  

telProdNpMonInterfFRLmiIRIncr 1.3.6.1.4.1.2007.4.1.2.2.2.9.6.1.15
IR adjustment percentage increment.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..100  

telProdNpMonInterfFRLmiIRDecr 1.3.6.1.4.1.2007.4.1.2.2.2.9.6.1.16
IR adjustment percentage decrement.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..100  

telProdNpMonInterfFRLmiIRMin 1.3.6.1.4.1.2007.4.1.2.2.2.9.6.1.17
Minimum IR as CIR percentage.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRLmiPTPLine 1.3.6.1.4.1.2007.4.1.2.2.2.9.6.1.18
Point to point line enabled (1) or not (2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

telProdNpMonInterfFRLmiPTPDlci 1.3.6.1.4.1.2007.4.1.2.2.2.9.6.1.19
Point to point dlci: used when the net is configured as point to point.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRLmiProtBroad 1.3.6.1.4.1.2007.4.1.2.2.2.9.6.1.20
Broadcast Protocol : Yes (1) or No (2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

telProdNpMonInterfFRLmiEmuMulticast 1.3.6.1.4.1.2007.4.1.2.2.2.9.6.1.21
Emulate Multicast: it shows if multicast emulation is enabled on each active PVC, yes (1) or no(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

telProdNpMonInterfFRLmiCongMonit 1.3.6.1.4.1.2007.4.1.2.2.2.9.6.1.22
Congestion Monitoring: congestion monitoring feature. The variable value may be (1) if it is enabled congestion monitoring or (2) if not.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

telProdNpMonInterfFRLmiCIRMonit 1.3.6.1.4.1.2007.4.1.2.2.2.9.6.1.23
FR CIR monitoring: indicates whether the circuit monitoring feature that enforces the transmission rate is enabled, yes (1) or no (2).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

telProdNpMonInterfFRLmiEnabPVCBkupRetTime 1.3.6.1.4.1.2007.4.1.2.2.2.9.6.1.24
Enable the prompt return from the PVC back-up. This variable only makes sense in a set operation (value 1). It can be enabled, but not disabled. In a read operation we will get the value 2 (ok).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable-prompt-return-from-PVC-back-up(1), ok(2)  

telProdNpMonInterfFRLmiCurrentRcvSeq 1.3.6.1.4.1.2007.4.1.2.2.2.9.6.1.25
Sequence number received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRLmiCurrentTxSeq 1.3.6.1.4.1.2007.4.1.2.2.2.9.6.1.26
Sequence number transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRLmiTotStatusEnq 1.3.6.1.4.1.2007.4.1.2.2.2.9.6.1.27
Total number of link status inquiries.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

telProdNpMonInterfFRLmiTotStatusResp 1.3.6.1.4.1.2007.4.1.2.2.2.9.6.1.28
Total number of link status responses.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

telProdNpMonInterfFRLmiTotSeqReq 1.3.6.1.4.1.2007.4.1.2.2.2.9.6.1.29
Total number of sequence requests.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

telProdNpMonInterfFRLmiTotSeqResp 1.3.6.1.4.1.2007.4.1.2.2.2.9.6.1.30
Total number of sequence responses.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

telProdNpMonInterfFRPvcStatusTable 1.3.6.1.4.1.2007.4.1.2.2.2.9.7
Table of PVC Status. The entry is determined by the interface number. It gives information about the number of allowable PVCs, configured PVCs, active PVCs, congested PVCs, PVCs that have joined the network and PVCs that are no longer on the network.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TelProdNpMonInterfFRPvcStatusEntry

telProdNpMonInterfFRPvcStatusEntry 1.3.6.1.4.1.2007.4.1.2.2.2.9.7.1
Each entry consists of the number of the node interface that is the table index, a variable to delete the table (in get operations shows the output from the last attempt for deleting counters of congested circuits, joined and left, and the set operation begins to delete counters), and the number of allowed PVCs, configured PVCs, active PVCs, congested PVCs, left PVCs (left net) and joined PVCs (join net).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  TelProdNpMonInterfFRPvcStatusEntry  

telProdNpMonInterfFRPvcStaIfcIndex 1.3.6.1.4.1.2007.4.1.2.2.2.9.7.1.1
Number of the node interface, that indicates the corresponding table entry (it is the table index).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRPvcStaClear 1.3.6.1.4.1.2007.4.1.2.2.2.9.7.1.2
This variable when is read shows the output from the last table delete attempt: the value is 2 if the deletion was performed succesfully, 3 if an error ocurred and 4 for an undefined result, that means that nobody has tried to delete the table yet. When we perform a set operation with value 1, the counters of the congested, joined and left circuits are deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER delete(1), ok(2), error(3), undefined(4)  

telProdNpMonInterfFRPvcStaTotAllow 1.3.6.1.4.1.2007.4.1.2.2.2.9.7.1.3
Number of allowable PVCs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..992  

telProdNpMonInterfFRPvcStaTotConfig 1.3.6.1.4.1.2007.4.1.2.2.2.9.7.1.4
Total number of currently configured PVCs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRPvcStaTotActiv 1.3.6.1.4.1.2007.4.1.2.2.2.9.7.1.5
Total number of active PVCs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRPvcStaTotCong 1.3.6.1.4.1.2007.4.1.2.2.2.9.7.1.6
Total number of congested PVCs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRPvcStaTotLeftNet 1.3.6.1.4.1.2007.4.1.2.2.2.9.7.1.7
Total number of left PVCs (left net).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRPvcStaTotJoinNet 1.3.6.1.4.1.2007.4.1.2.2.2.9.7.1.8
Total number of joined PVCs (join net).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRPvcTable 1.3.6.1.4.1.2007.4.1.2.2.2.9.8
Table of PVCs. The entry is determined by the interface number and the circuit number (dlci), that are the table index. It contains information about the circuit status (active, inactive, congested or removed), the type of circuit (permanent, switched or multicast), if the circuit is orphan, if transmitted data are encoded, number of frames and bytes transmitted and received, transmitted frames lost due to queue oveflow, frames lost due to input overrun, total number of FECNs, total number of BECNs, number of times the circuit congested, number of times the circuit was inactive, and circuit CIR, VIR, Bc and Be.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TelProdNpMonInterfFRPvcEntry

telProdNpMonInterfFRPvcEntry 1.3.6.1.4.1.2007.4.1.2.2.2.9.8.1
Each entry contains the number of node interface (first table index), the circuit number (dlci) (second index), a variable to delete the table (in get operations shows the output from the last attempt for deleting statistics, and the set operation begins to delete statistics), the circuit status (active, inactive, congested or removed), if the circuit is orphan, if transmitted data are encoded or not, number of frames and bytes transmitted and received, transmitted frames lost due to queue oveflow, frames lost due to input overrun, total number of FECNs, total number of BECNs, number of times the circuit congested, number of times the circuit was inactive, and circuit CIR, VIR, Bc and Be.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  TelProdNpMonInterfFRPvcEntry  

telProdNpMonInterfFRPvcIfcIndex 1.3.6.1.4.1.2007.4.1.2.2.2.9.8.1.1
Number of the node interface (it is the first table index).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRPvcDlciIndex 1.3.6.1.4.1.2007.4.1.2.2.2.9.8.1.2
Circuit number (dlci) for that interface (second table index).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRPvcClearStatistics 1.3.6.1.4.1.2007.4.1.2.2.2.9.8.1.3
This variable when is read shows the output from the last table delete attempt: the value is 2 if the deletion was performed succesfully, 3 if an error ocurred and 4 for an undefined result, that means that nobody has tried to delete the table yet. When we perform a set operation with value 1, the counters of PVCs statistics included in the table are deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER delete(1), ok(2), error(3), undefined(4)  

telProdNpMonInterfFRPvcName 1.3.6.1.4.1.2007.4.1.2.2.2.9.8.1.4
Circuit name.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

telProdNpMonInterfFRPvcCircStatus 1.3.6.1.4.1.2007.4.1.2.2.2.9.8.1.5
Circuit state: (1) inactive (waiting in LMI), (2) active, (3) congested, (4) removed. If this field stores a value different from the previous ones (active, congested or removed), the circuit is considered inactive.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER inactive(1), active(2), congested(3), removed(4)  

telProdNpMonInterfFRPvcCircType 1.3.6.1.4.1.2007.4.1.2.2.2.9.8.1.6
Type of circuit: (0) unknown, (1) permanent, (2) switched, (3) multicast.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER unknown(0), permanent(1), switched(2), multicast(3)  

telProdNpMonInterfFRPvcOrphan 1.3.6.1.4.1.2007.4.1.2.2.2.9.8.1.7
This variable indicates if the circuit is orphan, yes (1) or no (2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

telProdNpMonInterfFRPvcEncrypt 1.3.6.1.4.1.2007.4.1.2.2.2.9.8.1.8
This variable indicates if data are encoded, yes (1) or no (2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

telProdNpMonInterfFRPvcTxFrames 1.3.6.1.4.1.2007.4.1.2.2.2.9.8.1.9
Transmitted frames.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRPvcTxBytes 1.3.6.1.4.1.2007.4.1.2.2.2.9.8.1.10
Transmitted bytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRPvcRcvFrames 1.3.6.1.4.1.2007.4.1.2.2.2.9.8.1.11
Received frames.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRPvcRcvBytes 1.3.6.1.4.1.2007.4.1.2.2.2.9.8.1.12
Received bytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRPvcQueueOverf 1.3.6.1.4.1.2007.4.1.2.2.2.9.8.1.13
Transmitted frames lost due to queue overflow.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRPvcOverrun 1.3.6.1.4.1.2007.4.1.2.2.2.9.8.1.14
Frames lost due to input overrun. This variable only makes sense if the interface is not FR over ISDN or FR-DIAL, or FR over ISDN is not enabled. In the previous cases, tha variable will take the value 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRPvcTotFECNs 1.3.6.1.4.1.2007.4.1.2.2.2.9.8.1.15
Total FECNs: number of times inbound congestion was notified.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRPvcTotBECNs 1.3.6.1.4.1.2007.4.1.2.2.2.9.8.1.16
Total BECNs: number of times outbound congestion was notified.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRPvcTimesCong 1.3.6.1.4.1.2007.4.1.2.2.2.9.8.1.17
Number of times the circuit became congested.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRPvcTimesInact 1.3.6.1.4.1.2007.4.1.2.2.2.9.8.1.18
Number of times this circuit was inoperable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRPvcCIR 1.3.6.1.4.1.2007.4.1.2.2.2.9.8.1.19
CIR (Committed Information Rate), en bps.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 300..52428800  

telProdNpMonInterfFRPvcVIR 1.3.6.1.4.1.2007.4.1.2.2.2.9.8.1.20
VIR (Current Information Rate).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRPvcBc 1.3.6.1.4.1.2007.4.1.2.2.2.9.8.1.21
Bc (Commited Burst Size), en bits.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 300..52428800  

telProdNpMonInterfFRPvcBe 1.3.6.1.4.1.2007.4.1.2.2.2.9.8.1.22
Be (Excess Burst Size).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..52428800  

telProdNpMonInterfFRProtAddTable 1.3.6.1.4.1.2007.4.1.2.2.2.9.9
Table of protocol addresses. It contains information about the protocol type, the protocol address (it is possible to have several per protocol and interface) and the circuit number (dlci) associated to that address.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TelProdNpMonInterfFRProtAddEntry

telProdNpMonInterfFRProtAddEntry 1.3.6.1.4.1.2007.4.1.2.2.2.9.9.1
Each entry consists of the number of the interface (first table index), the protocol type (second index), the address order number (third index: it is necessary because it is possible to have several addresses associated to each protocol and interface), the protocol address and the dlci associated to that address.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  TelProdNpMonInterfFRProtAddEntry  

telProdNpMonInterfFRProtAddIfcIndex 1.3.6.1.4.1.2007.4.1.2.2.2.9.9.1.1
Number of the interface (first table index).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRProtAddProtocIndex 1.3.6.1.4.1.2007.4.1.2.2.2.9.9.1.2
Protocol type (second table index).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRProtAddOrdenIndex 1.3.6.1.4.1.2007.4.1.2.2.2.9.9.1.3
Address order number (it is possible to have several addresses associated to each protocol and interface). It is the third index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRProtAddAddress 1.3.6.1.4.1.2007.4.1.2.2.2.9.9.1.4
Protocol address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

telProdNpMonInterfFRProtAddDlci 1.3.6.1.4.1.2007.4.1.2.2.2.9.9.1.5
Dlci associated to that address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRActCallsTable 1.3.6.1.4.1.2007.4.1.2.2.2.9.10
Table of active calls. It contains information about the name and number (dlci) of the circuit through which the call is established, called and calling number, call reference and the hour, minute and second of the call beginning.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TelProdNpMonInterfFRActCallsEntry

telProdNpMonInterfFRActCallsEntry 1.3.6.1.4.1.2007.4.1.2.2.2.9.10.1
Each entry contains the number of the node interface (first index), the order number of the call in the table (second index), name and dlci of the circuit through which the call is established, called and calling number, call reference and the hour, minute and second of the call beginning.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  TelProdNpMonInterfFRActCallsEntry  

telProdNpMonInterfFRActCallsIfcIndex 1.3.6.1.4.1.2007.4.1.2.2.2.9.10.1.1
Number of the interface (first table index).
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRActCallsOrdenIndex 1.3.6.1.4.1.2007.4.1.2.2.2.9.10.1.2
Call order or position in the table (second index).
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRActCallsCircuitName 1.3.6.1.4.1.2007.4.1.2.2.2.9.10.1.3
Circuit name.
Status: obsolete Access: read-only
OBJECT-TYPE    
  DisplayString  

telProdNpMonInterfFRActCallsDlci 1.3.6.1.4.1.2007.4.1.2.2.2.9.10.1.4
Dlci Number of the circuit through which the call is established.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRActCallsCalledNum 1.3.6.1.4.1.2007.4.1.2.2.2.9.10.1.5
Called number
Status: obsolete Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..15)  

telProdNpMonInterfFRActCallsCallingNum 1.3.6.1.4.1.2007.4.1.2.2.2.9.10.1.6
Calling number.
Status: obsolete Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..15)  

telProdNpMonInterfFRActCallsRef 1.3.6.1.4.1.2007.4.1.2.2.2.9.10.1.7
Call reference.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRActCallsStartHour 1.3.6.1.4.1.2007.4.1.2.2.2.9.10.1.8
Indicates the hour the call was initialized.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRActCallsStartMin 1.3.6.1.4.1.2007.4.1.2.2.2.9.10.1.9
Indicates the minute the call was initialized.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRActCallsStartSec 1.3.6.1.4.1.2007.4.1.2.2.2.9.10.1.10
Indicates the second the call was initialized.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRRelCallsTable 1.3.6.1.4.1.2007.4.1.2.2.2.9.11
Table of released calls. Contains information about the name and dlci of the circuit through which the call was initialized, called and calling numbers, cause and diagnosis of the release, the hour, minute and second the call finished.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TelProdNpMonInterfFRRelCallsEntry

telProdNpMonInterfFRRelCallsEntry 1.3.6.1.4.1.2007.4.1.2.2.2.9.11.1
Each entry contains the number of the node interface (first index), the order number of the call in the table (second index), name and dlci of the circuit through which the call is established, called and calling number, cause and diagnosis of the release, the hour, minute and second the call finished.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  TelProdNpMonInterfFRRelCallsEntry  

telProdNpMonInterfFRRelCallsIndex 1.3.6.1.4.1.2007.4.1.2.2.2.9.11.1.1
Number of interface (first table index).
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRRelCallsOrdenIndex 1.3.6.1.4.1.2007.4.1.2.2.2.9.11.1.2
Call order or position in the table (second index).
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRRelCallsClear 1.3.6.1.4.1.2007.4.1.2.2.2.9.11.1.3
This variable when is read shows the output from the last table delete attempt: the value is 2 if the deletion was performed succesfully, 3 if an error ocurred and 4 for an undefined result, that means that nobody has tried to delete the buffer of released calls yet. When we perform a set operation with value 1, the buffer of released calls is deleted.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER delete(1), ok(2), error(3), undefined(4)  

telProdNpMonInterfFRRelCallsCircName 1.3.6.1.4.1.2007.4.1.2.2.2.9.11.1.4
Name of the circuit through which the call was established.
Status: obsolete Access: read-only
OBJECT-TYPE    
  DisplayString  

telProdNpMonInterfFRRelCallsDlci 1.3.6.1.4.1.2007.4.1.2.2.2.9.11.1.5
Dlci number of the circuit through which the call was established.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRRelCallsCalledNum 1.3.6.1.4.1.2007.4.1.2.2.2.9.11.1.6
Called number.
Status: obsolete Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..15)  

telProdNpMonInterfFRRelCallsCallingNum 1.3.6.1.4.1.2007.4.1.2.2.2.9.11.1.7
Calling number.
Status: obsolete Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..15)  

telProdNpMonInterfFRRelCallsCL 1.3.6.1.4.1.2007.4.1.2.2.2.9.11.1.8
This indicates why the call has been released.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRRelCallsDL 1.3.6.1.4.1.2007.4.1.2.2.2.9.11.1.9
Indicates the released call diagnosis.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRRelCallsStartHour 1.3.6.1.4.1.2007.4.1.2.2.2.9.11.1.10
Indicates the hour the call was initialized.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRRelCallsStartMin 1.3.6.1.4.1.2007.4.1.2.2.2.9.11.1.11
Indicates the minute the call was initialized.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRRelCallsStartSec 1.3.6.1.4.1.2007.4.1.2.2.2.9.11.1.12
Indicates the second the call was initialized.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRRelCallsEndHour 1.3.6.1.4.1.2007.4.1.2.2.2.9.11.1.13
Indicates the hour the call was released.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRRelCallsEndMin 1.3.6.1.4.1.2007.4.1.2.2.2.9.11.1.14
Indicates the minute the call was released.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpMonInterfFRRelCallsEndSec 1.3.6.1.4.1.2007.4.1.2.2.2.9.11.1.15
Indicates the second the call was released.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER