TELDAT-MON-INTERF-ASL-MIB

File: TELDAT-MON-INTERF-ASL-MIB.mib (18564 bytes)

Imported modules

RFC1155-SMI	RFC-1212	RFC1213-MIB
TELDAT-SW-STRUCTURE-MIB

Imported symbols

Counter	OBJECT-TYPE	DisplayString
telProdNpMonInterfRouter

Defined Types

TelProdNpMonIfcASLGlobalEntry
SEQUENCE
	telProdNpMonIfcASLGloIndex	INTEGER
	telProdNpMonIfcASLGloDriverType	DisplayString
	telProdNpMonIfcASLGloSpeed	INTEGER
	telProdNpMonIfcASLGloThrou	INTEGER
	telProdNpMonIfcASLGloLastThrou	INTEGER
	telProdNpMonIfcASLGloBitsChar	INTEGER
	telProdNpMonIfcASLGloStopBits	INTEGER
	telProdNpMonIfcASLGloParitySel	INTEGER
	telProdNpMonIfcASLGloLastResetWeek	INTEGER
	telProdNpMonIfcASLGloLastResetDay	INTEGER
	telProdNpMonIfcASLGloLastResetHour	INTEGER
	telProdNpMonIfcASLGloLastResetMin	INTEGER
	telProdNpMonIfcASLGloLastResetSec	INTEGER
	telProdNpMonIfcASLGloLoopback	INTEGER
	telProdNpMonIfcASLGloEcho	INTEGER
	telProdNpMonIfcASLGloIgnoreCD	INTEGER
	telProdNpMonIfcASLGloDisconnectCD	INTEGER
	telProdNpMonIfcASLGloIgnoreDSR	INTEGER

TelProdNpMonIfcASLRS232Entry
SEQUENCE
	telProdNpMonIfcASLRS232IfcIndex	INTEGER
	telProdNpMonIfcASLRS232CircIndex	INTEGER
	telProdNpMonIfcASLRS232Circuit	INTEGER
	telProdNpMonIfcASLRS232Nickname	DisplayString
	telProdNpMonIfcASLRS232State	DisplayString

TelProdNpMonIfcASLStatsEntry
SEQUENCE
	telProdNpMonIfcASLStatsIndex	INTEGER
	telProdNpMonIfcASLStatsClear	INTEGER
	telProdNpMonIfcASLStatsParityErr	Counter
	telProdNpMonIfcASLStatsDataErr	Counter
	telProdNpMonIfcASLStatsOverrun	Counter

Defined Values

telProdNpMonInterfASL		1.3.6.1.4.1.2007.4.1.2.2.2.16
OBJECT IDENTIFIER

telProdNpMonIfcASLGlobalTable		1.3.6.1.4.1.2007.4.1.2.2.2.16.1
This table contains general information about asynchronous serial line interfaces. There will be one entry per each interface of this kind.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TelProdNpMonIfcASLGlobalEntry

telProdNpMonIfcASLGlobalEntry		1.3.6.1.4.1.2007.4.1.2.2.2.16.1.1
Each entry contains the interface number that will be the table index used to go over the table, the line speed, the throughput in bits per second, the last throughput, the number of bits per character, the number of stop bits, the parity chosen (if it exists), the number of parity errors, data errors, overrun errors, the amount of time passed since the last port reset and variables to indicate if the SCC loopback mode or echo mode are active, if CD or DSR signal states are ignored and if CD signal is disconnected from internal hardware.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	TelProdNpMonIfcASLGlobalEntry

telProdNpMonIfcASLGloIndex		1.3.6.1.4.1.2007.4.1.2.2.2.16.1.1.1
Interface number. The interface must be asynchronous serial line. It is the table index.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

telProdNpMonIfcASLGloDriverType		1.3.6.1.4.1.2007.4.1.2.2.2.16.1.1.2
Type of physical driverP: (1) DCE, (2) DTE. The variable is a string.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

telProdNpMonIfcASLGloSpeed		1.3.6.1.4.1.2007.4.1.2.2.2.16.1.1.3
Speed of the asynchronous serial line. (Clock speed, in bps).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

telProdNpMonIfcASLGloThrou		1.3.6.1.4.1.2007.4.1.2.2.2.16.1.1.4
Throughput in bits per second. It is the mean effective speed.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

telProdNpMonIfcASLGloLastThrou		1.3.6.1.4.1.2007.4.1.2.2.2.16.1.1.5
Last throughput, in bits per second. It is the mean instantaneous speed.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

telProdNpMonIfcASLGloBitsChar		1.3.6.1.4.1.2007.4.1.2.2.2.16.1.1.6
Number of bits per character.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

telProdNpMonIfcASLGloStopBits		1.3.6.1.4.1.2007.4.1.2.2.2.16.1.1.7
Number of stop bits.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

telProdNpMonIfcASLGloParitySel		1.3.6.1.4.1.2007.4.1.2.2.2.16.1.1.8
Parity chosen (if parity has been chosen). The possible values are: (0) if no parity has been selected, (1) odd, (2) space, (3) even, (4) mark.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	none(0), odd(1), space(2), even(3), mark(4)

telProdNpMonIfcASLGloLastResetWeek		1.3.6.1.4.1.2007.4.1.2.2.2.16.1.1.9
Weeks passed since the last port reset.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

telProdNpMonIfcASLGloLastResetDay		1.3.6.1.4.1.2007.4.1.2.2.2.16.1.1.10
Days passed since the last port reset: the remaining days that we get after counting the number of weeks that are not enough to form a week, this implies that the value of the variable must be under 7.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

telProdNpMonIfcASLGloLastResetHour		1.3.6.1.4.1.2007.4.1.2.2.2.16.1.1.11
Hours passed since the last reset of the port. If it has passed more than a week, this variable indicates the number of hours to be added to the number of weeks and days, and its value should be under 24 so as not form a complete day.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

telProdNpMonIfcASLGloLastResetMin		1.3.6.1.4.1.2007.4.1.2.2.2.16.1.1.12
Minutes passed since the last reset of the port. This variable indicates the number of minutes since the last hour was added to the hour counter.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

telProdNpMonIfcASLGloLastResetSec		1.3.6.1.4.1.2007.4.1.2.2.2.16.1.1.13
Seconds passed since the last reset of the port. The total time passed will be calculated by adding weeks, days, hours, minutes and seconds since the last reset.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

telProdNpMonIfcASLGloLoopback		1.3.6.1.4.1.2007.4.1.2.2.2.16.1.1.14
This variable indicates if SCC loopback mode is active: transmitter is connected internally to the receiver.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	active(1), inactive(2)

telProdNpMonIfcASLGloEcho		1.3.6.1.4.1.2007.4.1.2.2.2.16.1.1.15
This variable indicates if SCC echo mode is active: transmitter resends received data.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	active(1), inactive(2)

telProdNpMonIfcASLGloIgnoreCD		1.3.6.1.4.1.2007.4.1.2.2.2.16.1.1.16
This variable indicates if CD signal state is ignored.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	yes(1), no(2)

telProdNpMonIfcASLGloDisconnectCD		1.3.6.1.4.1.2007.4.1.2.2.2.16.1.1.17
This variable indicates if CD signal is disconnected from internal hardware.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	yes(1), no(2)

telProdNpMonIfcASLGloIgnoreDSR		1.3.6.1.4.1.2007.4.1.2.2.2.16.1.1.18
This variable indicates if DSR signal state is ignored.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	yes(1), no(2)

telProdNpMonIfcASLRS232Table		1.3.6.1.4.1.2007.4.1.2.2.2.16.2
This table contains the signals or circuits RS232. It shows wether the signals are active or not. The entry number is determined by the interface number considered.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TelProdNpMonIfcASLRS232Entry

telProdNpMonIfcASLRS232Entry		1.3.6.1.4.1.2007.4.1.2.2.2.16.2.1
Each entry contains the interface number of the node considered, which will be the first index used to go over the table, the order number of the circuit inside that interface (second index), which must be between 1 and a maximum value that depends on the conector type (the highest value will be 7), the circuit number (105, 106, 107, 108, 109, 125, 141), its name (RTS, CTS, DSR, DTR, DCD, RI, LL) and wether it is active or not.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	TelProdNpMonIfcASLRS232Entry

telProdNpMonIfcASLRS232IfcIndex		1.3.6.1.4.1.2007.4.1.2.2.2.16.2.1.1
Interface number, which must be synchronous serial line. It is the first table index.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

telProdNpMonIfcASLRS232CircIndex		1.3.6.1.4.1.2007.4.1.2.2.2.16.2.1.2
Second table index. This value goes between 1 to the number of this type of circuits, that varies depending on the conector type.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..7

telProdNpMonIfcASLRS232Circuit		1.3.6.1.4.1.2007.4.1.2.2.2.16.2.1.3
RS232 circuit number. The possible values are 105, 106, 107, 108, 109, 125 y 141.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	105..141

telProdNpMonIfcASLRS232Nickname		1.3.6.1.4.1.2007.4.1.2.2.2.16.2.1.4
Circuit name.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

telProdNpMonIfcASLRS232State		1.3.6.1.4.1.2007.4.1.2.2.2.16.2.1.5
Signal state (circuit signals): on, off or unknown.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

telProdNpMonIfcASLStatsTable		1.3.6.1.4.1.2007.4.1.2.2.2.16.3
This table contains statistics of asynchronous serial line interfaces.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TelProdNpMonIfcASLStatsEntry

telProdNpMonIfcASLStatsEntry		1.3.6.1.4.1.2007.4.1.2.2.2.16.3.1
Each entry contains the interface number that is the table index, the variable that shows the output from the last table deletion operation (in get operations) or begins the deletion (in set operations), the number of parity errors, the number of data errors and the number of overrun errors.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	TelProdNpMonIfcASLStatsEntry

telProdNpMonIfcASLStatsIndex		1.3.6.1.4.1.2007.4.1.2.2.2.16.3.1.1
Interface number. The interface must be asynchronous serial line to appear in the table. It is the table index.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

telProdNpMonIfcASLStatsClear		1.3.6.1.4.1.2007.4.1.2.2.2.16.3.1.2
This variable when is read shows the output from the last table delete attempt: the value is 2 if the deletion was performed succesfully, 3 if an error ocurred and 4 for an undefined result, that means that nobody has tried to delete the table yet. In set operations, the value 1 (it is the only value that can be assigned by a writing operation) causes a table deletion: frame counters are set to 0.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	delete(1), ok(2), error(3), undefined(4)

telProdNpMonIfcASLStatsParityErr		1.3.6.1.4.1.2007.4.1.2.2.2.16.3.1.3
Number of parity errors.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

telProdNpMonIfcASLStatsDataErr		1.3.6.1.4.1.2007.4.1.2.2.2.16.3.1.4
Number of data errors.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

telProdNpMonIfcASLStatsOverrun		1.3.6.1.4.1.2007.4.1.2.2.2.16.3.1.5
Number of overrun errors.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter