TELDAT-CFG-PROTOCOL-IP-MIB

File: TELDAT-CFG-PROTOCOL-IP-MIB.mib (32918 bytes)

Imported modules

RFC1155-SMI RFC-1212 TELDAT-SW-STRUCTURE-MIB

Imported symbols

IpAddress OBJECT-TYPE telProdNpConfProtocol

Defined Types

TelProdNpIPDirEntry  
SEQUENCE    
  telProdNpIPDirInterfazIndex INTEGER
  telProdNpIPDirIndex INTEGER
  telProdNpIPDirStatus INTEGER
  telProdNpIPDirIP IpAddress
  telProdNpIPDirMascara IpAddress
  telProdNpIPDirBroadcastType INTEGER
  telProdNpIPDirBroadcastRell INTEGER

TelProdNpIPRutEntry  
SEQUENCE    
  telProdNpIPRutIndex INTEGER
  telProdNpIPRutStatus INTEGER
  telProdNpIPRutDirIPFinal IpAddress
  telProdNpIPRutMascara IpAddress
  telProdNpIPRutDirIPNext IpAddress
  telProdNpIPRutCost INTEGER

TelProdNpIPCtrlEntry  
SEQUENCE    
  telProdNpIPCtrlIndex INTEGER
  telProdNpIPCtrlStatus INTEGER
  telProdNpIPCtrlPriority INTEGER
  telProdNpIPCtrlAccessType INTEGER
  telProdNpIPCtrlDirIPOrigin IpAddress
  telProdNpIPCtrlMasIPOrigin IpAddress
  telProdNpIPCtrlDirIPFinal IpAddress
  telProdNpIPCtrlMasIPFinal IpAddress
  telProdNpIPCtrlProtStart INTEGER
  telProdNpIPCtrlProtEnd INTEGER
  telProdNpIPCtrlPortStart INTEGER
  telProdNpIPCtrlPortEnd INTEGER
  telProdNpIPCtrlSrcPortStart INTEGER
  telProdNpIPCtrlSrcPortEnd INTEGER

TelProdNpIPFilEntry  
SEQUENCE    
  telProdNpIPFilIndex INTEGER
  telProdNpIPFilStatus INTEGER
  telProdNpIPFilDirIPFinal IpAddress
  telProdNpIPFilMasIPNet IpAddress

TelProdNpIPAggRutEntry  
SEQUENCE    
  telProdNpIPAggRutIndex INTEGER
  telProdNpIPAggRutStatus INTEGER
  telProdNpIPAggRutDirIPFinal IpAddress
  telProdNpIPAggRutMascara IpAddress
  telProdNpIPAggRutCost INTEGER

Defined Values

telProdNpConfProtIP 1.3.6.1.4.1.2007.4.1.1.5.1
OBJECT IDENTIFIER    

telProdNpIPGloGroup 1.3.6.1.4.1.2007.4.1.1.5.1.1
OBJECT IDENTIFIER    

telProdNpIPGloDirIPInternal 1.3.6.1.4.1.2007.4.1.1.5.1.1.1
Internal IP address of the packets.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

telProdNpIPGloRouterID 1.3.6.1.4.1.2007.4.1.1.5.1.1.2
IP address with which router is identified.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

telProdNpIPGloSizeRoutingTable 1.3.6.1.4.1.2007.4.1.1.5.1.1.3
Maximum routing table size. 0 = unlimited. 64..1000000000 = routing table size limit. Default value is 0 (unlimited).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..1000000000  

telProdNpIPGloSizeBuffReassembly 1.3.6.1.4.1.2007.4.1.1.5.1.1.4
Reassembly buffer size. Default value is 12000
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 2048..65535  

telProdNpIPGloSizeRoutingCache 1.3.6.1.4.1.2007.4.1.1.5.1.1.5
Router cache size. Default value is 64.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 64..10000  

telProdNpIPGloDirectBroadcast 1.3.6.1.4.1.2007.4.1.1.5.1.1.6
Direct broadcast activation. Default value of the device is yes(1).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

telProdNpIPGloMultiwayPaquet 1.3.6.1.4.1.2007.4.1.1.5.1.1.7
Multipath activation: (1) Per packet multipath, round-robin strategy. (2) Multipath dissabled. (3) Per source and destination multipath (session). (4) Per packet multipath, relative-weights strategy. Default value is disabled(2).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER per-packet-round-robin(1), disabled(2), per-destination(3), per-packet-relative-weights(4)  

telProdNpIPGloHabAccessControl 1.3.6.1.4.1.2007.4.1.1.5.1.1.8
Access controls activation. If they are disabled, telProdNpIPCtrlTable table does not exist. Default value of the device is NO(2).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

telProdNpIPDelAllDir 1.3.6.1.4.1.2007.4.1.1.5.1.1.9
This variable deletes all rows of the IP addresses table (telProdNpIPDirTable).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER set-ok(1), set-non-ok(2), indeterminate(3)  

telProdNpIPDelAllRut 1.3.6.1.4.1.2007.4.1.1.5.1.1.10
This variable deletes all rows of the IP routes table (telProdNpIPRutTable).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER set-ok(1), set-non-ok(2), indeterminate(3)  

telProdNpIPDelAllFil 1.3.6.1.4.1.2007.4.1.1.5.1.1.11
This variable deletes all rows of the filters table (telProdNpIPFilTable).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER set-ok(1), set-non-ok(2), indeterminate(3)  

telProdNpIPDelAllCtl 1.3.6.1.4.1.2007.4.1.1.5.1.1.12
This variable deletes all rows of the access-controls table (telProdNpIPCtrlTable).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER set-ok(1), set-non-ok(2), indeterminate(3)  

telProdNpIPGloHabIPClassless 1.3.6.1.4.1.2007.4.1.1.5.1.1.15
This variable allows enabling IP Classless. Default value of the device is NO(2).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

telProdNpIPGloDirIPManagement 1.3.6.1.4.1.2007.4.1.1.5.1.1.16
Management IP address for traps.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

telProdNpIPDirTable 1.3.6.1.4.1.2007.4.1.1.5.1.2
Addresses list. There are two table indexes: the interface and the IP address index.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TelProdNpIPDirEntry

telProdNpIPDirEntry 1.3.6.1.4.1.2007.4.1.1.5.1.2.1
Each entry consists of the addresses, the interface number (first address), the IP address index (second index), the table control variable, the IP address, the mask associated to that IP address, the broadcast type and the broadcast stuffing of that IP address.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  TelProdNpIPDirEntry  

telProdNpIPDirInterfazIndex 1.3.6.1.4.1.2007.4.1.1.5.1.2.1.1
Interface number associated to that IP address. It is the first table index. The interfaces of the ROUTER part (from the first (LAN) till Router->Node) are the only possible ones.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpIPDirIndex 1.3.6.1.4.1.2007.4.1.1.5.1.2.1.2
Entry number of the IP address. It is the second table index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpIPDirStatus 1.3.6.1.4.1.2007.4.1.1.5.1.2.1.3
Table control variable. Set to 1 does nothing. Set to 2 adds a new row (IP address) in the table with the default values, and returns 2. If it already existed, it modifies IP address as it is described in the following variable(telProdNpIPDirIP). The new row must be added immediately after the last index. Set to 3 deletes all the table fields corresponding to the index, and returns 3. Get returns 1 if the address exists.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER valid(1), add(2), delete(3)  

telProdNpIPDirIP 1.3.6.1.4.1.2007.4.1.1.5.1.2.1.4
IP address of this entry. If it is the first interface (number 1, LAN), default value is 0.0.0.0. If it is another interface, default value is 0.0.0.(interface number). If it is requested a new row for an interface to which a row whith the default values already has been assigned, then default IP address will be 0.0.0.(number), where number is the highest interface number (which can have IP address) + 1. And if this IP address already exists, the following one to the last one which exists will be assigned to the interface (adding 1 to the fourth byte). If it is tried to realize a SET with an existing address in another interface, then it returns ERROR. It is allowed realizing a SET with the same address. If it is realized a SET to an address whose first byte is zero, then it only allows the 0.0.0.(number) format, where number is just like before. If the address first byte is zero, then the mask is 0.0.0.0.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

telProdNpIPDirMascara 1.3.6.1.4.1.2007.4.1.1.5.1.2.1.5
Mask associated to this IP address. If it is realized a SET to this variable, and the associate IP address has the first byte to zero, then the mask can only be 0.0.0.0. In another case, it returns ERROR. If IP address starts at zero, then default value will be 0.0.0.0. If it isn't so, then default value will be 255.0.0.0.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

telProdNpIPDirBroadcastType 1.3.6.1.4.1.2007.4.1.1.5.1.2.1.6
Broadcast type. Default value is net (1).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER net(1), medium-local(2)  

telProdNpIPDirBroadcastRell 1.3.6.1.4.1.2007.4.1.1.5.1.2.1.7
Broadcast stuffing. Value 0 shows that it is stuffed with zeros. Value 1 shows that it is stuffed with zeros. Default value is 0.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..1  

telProdNpIPRutTable 1.3.6.1.4.1.2007.4.1.1.5.1.4
Routes list. The table index is the route position.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TelProdNpIPRutEntry

telProdNpIPRutEntry 1.3.6.1.4.1.2007.4.1.1.5.1.4.1
Each entry consists of the routes, the route number (table index), the table control variable, the ending IP address, the mask associated to that IP address, the following IP address, the mask associated to to that IP address and the cost.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  TelProdNpIPRutEntry  

telProdNpIPRutIndex 1.3.6.1.4.1.2007.4.1.1.5.1.4.1.1
It is the route position in the table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpIPRutStatus 1.3.6.1.4.1.2007.4.1.1.5.1.4.1.2
Table control variable. Set to 1 does nothing. Set to 2 adds a new row (route) in the table with the default values and returns 2. If it already existed, then it returns error. It must be added immediately after the last index. Set to 3 deletes all table fields corresponding to that route, and returns 3. Get returns 1 if the route exists.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER valid(1), add(2), delete(3)  

telProdNpIPRutDirIPFinal 1.3.6.1.4.1.2007.4.1.1.5.1.4.1.3
Destination IP address. If address is repeated, then it retuns error (it must be repeated the IP address and the corresponding mask.) Default value is 0.0.0.0.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

telProdNpIPRutMascara 1.3.6.1.4.1.2007.4.1.1.5.1.4.1.4
Mask associated to this IP address. If the mask is repeated, then it returns error (it must be repeated the IP address and the corresponding mask.) Default value is 0.0.0.0.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

telProdNpIPRutDirIPNext 1.3.6.1.4.1.2007.4.1.1.5.1.4.1.5
IP address of the next hop. Default value is 0.0.0.0.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

telProdNpIPRutCost 1.3.6.1.4.1.2007.4.1.1.5.1.4.1.6
Hops cost. Default value is 1.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

telProdNpIPCtrlTable 1.3.6.1.4.1.2007.4.1.1.5.1.5
Access control list. The table index is the access control position.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TelProdNpIPCtrlEntry

telProdNpIPCtrlEntry 1.3.6.1.4.1.2007.4.1.1.5.1.5.1
Each entry consists of the access controls information: the access control number (table index), the table control variable, the priority, the access type, the source IP address, the mask associated to source IP address, the destination IP address, the mask associated to destination IP address, the starting protocol, the ending protocol, the starting port and the ending port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  TelProdNpIPCtrlEntry  

telProdNpIPCtrlIndex 1.3.6.1.4.1.2007.4.1.1.5.1.5.1.1
It is the access control position in the table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpIPCtrlStatus 1.3.6.1.4.1.2007.4.1.1.5.1.5.1.2
Table control variable. Set to 1 does nothing. Set to 2 adds a new row (access control) in the table with the default values and returns 2. If it already existed, then it returns error. It must be added immediately after the last index. Set to 3 deletes all table fields corresponding to that access control, and returns 3. Get returns 1 if the control exists.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER valid(1), add(2), delete(3)  

telProdNpIPCtrlPriority 1.3.6.1.4.1.2007.4.1.1.5.1.5.1.3
Access control priority. It coincides with its position in the table. Default value is 1. When realizing a set, the position behind which the access control will be placed, must be indicated.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

telProdNpIPCtrlAccessType 1.3.6.1.4.1.2007.4.1.1.5.1.5.1.4
Access control type. Default value is 1 (inclusive).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER exclusive(1), inclusive(2)  

telProdNpIPCtrlDirIPOrigin 1.3.6.1.4.1.2007.4.1.1.5.1.5.1.5
Source IP address. Default value is 0.0.0.0. If the address is repeated, then it returns error.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

telProdNpIPCtrlMasIPOrigin 1.3.6.1.4.1.2007.4.1.1.5.1.5.1.6
Mask associated to source IP address. If this condition is not fulfilled, SourceIPAddress & (~(SourceMask) )=0, then the mask is inconsistent. Default value is 0.0.0.0.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

telProdNpIPCtrlDirIPFinal 1.3.6.1.4.1.2007.4.1.1.5.1.5.1.7
Destination IP address. Default value is 0.0.0.0. If the address is repeated, then it returns error.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

telProdNpIPCtrlMasIPFinal 1.3.6.1.4.1.2007.4.1.1.5.1.5.1.8
Mask associated to destination IP address. If this condition is not fulfilled, DestinationIPAddress & (~(DestinationMask) )=0, then the mask is inconsistent. Default value is 0.0.0.0.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

telProdNpIPCtrlProtStart 1.3.6.1.4.1.2007.4.1.1.5.1.5.1.9
Starting protocol. If it is tried to introduce a value higher than telProdNpIPCtrlProtEnd, then it returns error. Default value is 0.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

telProdNpIPCtrlProtEnd 1.3.6.1.4.1.2007.4.1.1.5.1.5.1.10
Ending protocol. If it is tried to introduce a value lower than telProdNpIPCtrlProtStart, then it returns error. Default value is 255.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

telProdNpIPCtrlPortStart 1.3.6.1.4.1.2007.4.1.1.5.1.5.1.11
Starting destination port for UDP or TCP protocol and starting code for ICMP protocol. If it is tried to introduce a value higher than telProdNpIPCtrlPortEnd, then it returns error. Default value is 0.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

telProdNpIPCtrlPortEnd 1.3.6.1.4.1.2007.4.1.1.5.1.5.1.12
Ending destination port for UDP or TCP protocol and ending code for ICMP protocol. If it is tried to introduce a value lower than telProdNpIPCtrlPortStart, then it returns error. Default value is 65535.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

telProdNpIPCtrlSrcPortStart 1.3.6.1.4.1.2007.4.1.1.5.1.5.1.13
Starting source port for UDP or TCP protocol and starting type for ICMP protocol. If it is tried to introduce a value higher than telProdNpIPCtrlSrcPortEnd, then it returns error. Default value is 0.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

telProdNpIPCtrlSrcPortEnd 1.3.6.1.4.1.2007.4.1.1.5.1.5.1.14
Ending source port for UDP or TCP protocol and endng type for ICMP protocol. If it is tried to introduce a value lower than telProdNpIPCtrlSrcPortStart, then it returns error. Default value is 65535.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

telProdNpIPFilTable 1.3.6.1.4.1.2007.4.1.1.5.1.6
Filters list. The table index is the filter position.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TelProdNpIPFilEntry

telProdNpIPFilEntry 1.3.6.1.4.1.2007.4.1.1.5.1.6.1
Each entry consists of the filters, the filter number (table index), the table control variable, the destination IP address and the mask associated to that IP address.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  TelProdNpIPFilEntry  

telProdNpIPFilIndex 1.3.6.1.4.1.2007.4.1.1.5.1.6.1.1
It is the filter position in the table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpIPFilStatus 1.3.6.1.4.1.2007.4.1.1.5.1.6.1.2
Table control variable. Set to 1 does nothing. Set to 2 adds a new row (filter) in the table with the default values and returns 2. If it already existed, then it returns error. It must be added immediately after the last index. Set to 3 deletes all table fields corresponding to that filter, and returns 3. Get returns 1 if the filter exists.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER valid(1), add(2), delete(3)  

telProdNpIPFilDirIPFinal 1.3.6.1.4.1.2007.4.1.1.5.1.6.1.3
Destination IP address. Default value is 0.0.0.0. If address is repeated, then it retuns error (it must be repeated the IP address and the corresponding mask).
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

telProdNpIPFilMasIPNet 1.3.6.1.4.1.2007.4.1.1.5.1.6.1.4
Mask associated to this IP address. If mask is repeated, then it retuns error (it must be repeated the IP address and the corresponding mask). Default value is 0.0.0.0.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

telProdNpIPAggRutTable 1.3.6.1.4.1.2007.4.1.1.5.1.8
Aggregation routes table. The table index is the route position.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TelProdNpIPAggRutEntry

telProdNpIPAggRutEntry 1.3.6.1.4.1.2007.4.1.1.5.1.8.1
Each entry consists of the routes, the route number (table index), the table control variable, the ending IP address, the mask associated to that IP address and the cost.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  TelProdNpIPAggRutEntry  

telProdNpIPAggRutIndex 1.3.6.1.4.1.2007.4.1.1.5.1.8.1.1
It is the route position in the table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telProdNpIPAggRutStatus 1.3.6.1.4.1.2007.4.1.1.5.1.8.1.2
Table control variable. Set to 1 does nothing. Set to 2 deletes that route. Get returns 1 if the route exists.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER valid(1), delete(2)  

telProdNpIPAggRutDirIPFinal 1.3.6.1.4.1.2007.4.1.1.5.1.8.1.3
Destination IP address. To introduce a new aggregation route, a SET operation must be carried out, giving this variable a certain value (IP address). The index corresponding to this address must be higher than the entries number of that table. Default value is 0.0.0.0.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

telProdNpIPAggRutMascara 1.3.6.1.4.1.2007.4.1.1.5.1.8.1.4
Mask associated to this IP address. To introduce a new aggregation route, a SET operation must be carried out, giving this variable a certain value (mask). The index corresponding to this address must be higher than the entries number of that table. Default value is 0.0.0.0.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

telProdNpIPAggRutCost 1.3.6.1.4.1.2007.4.1.1.5.1.8.1.5
Hops cost. Default value is 1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor