SYNOLOGY-UPS-MIB

File: SYNOLOGY-UPS-MIB.mib (34759 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC NET-SNMP-TC
SNMPv2-CONF

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Integer32
enterprises DisplayString TEXTUAL-CONVENTION
Float MODULE-COMPLIANCE OBJECT-GROUP

Defined Types

NonNegativeInteger  
This data type is a non-negative value.
TEXTUAL-CONVENTION    
  Integer32 0..2147483647  

Defined Values

synoUPS 1.3.6.1.4.1.6574.4
Characteristics of the ups information
MODULE-IDENTITY    

synology 1.3.6.1.4.1.6574
OBJECT IDENTIFIER    

upsDevice 1.3.6.1.4.1.6574.4.1
OBJECT IDENTIFIER    

upsDeviceModel 1.3.6.1.4.1.6574.4.1.1
Device model
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsDeviceManufacturer 1.3.6.1.4.1.6574.4.1.2
Device manufacturer
OBJECT-TYPE    
  DisplayString Size(0..31)  

upsDeviceSerial 1.3.6.1.4.1.6574.4.1.3
Device serial number.
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsDeviceType 1.3.6.1.4.1.6574.4.1.4
Device type (ups, pdu, scd, psu)
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsDeviceDescription 1.3.6.1.4.1.6574.4.1.5
Device description.
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsDeviceContact 1.3.6.1.4.1.6574.4.1.6
Device administrator name.
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsDeviceLocation 1.3.6.1.4.1.6574.4.1.7
Device physical location.
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsDevicePart 1.3.6.1.4.1.6574.4.1.8
Device part number.
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsDeviceMACAddr 1.3.6.1.4.1.6574.4.1.9
Physical network address of the device.
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsInfo 1.3.6.1.4.1.6574.4.2
OBJECT IDENTIFIER    

upsInfoStatus 1.3.6.1.4.1.6574.4.2.1
UPS status.
OBJECT-TYPE    
  DisplayString Size(0..31)  

upsInfoAlarm 1.3.6.1.4.1.6574.4.2.2
UPS alarms
OBJECT-TYPE    
  DisplayString Size(0..31)  

upsInfoTime 1.3.6.1.4.1.6574.4.2.3
Internal UPS clock time
OBJECT-TYPE    
  DisplayString Size(0..31)  

upsInfoDate 1.3.6.1.4.1.6574.4.2.4
Internal UPS clock date
OBJECT-TYPE    
  DisplayString Size(0..31)  

upsInfoModel 1.3.6.1.4.1.6574.4.2.5
UPS model
OBJECT-TYPE    
  DisplayString Size(0..31)  

upsInfoMfr 1.3.6.1.4.1.6574.4.2.6
OBJECT IDENTIFIER    

upsInfoMfrName 1.3.6.1.4.1.6574.4.2.6.1
UPS manufacturer
OBJECT-TYPE    
  DisplayString Size(0..31)  

upsInfoMfrDate 1.3.6.1.4.1.6574.4.2.6.2
UPS manufacturing date
OBJECT-TYPE    
  DisplayString Size(0..31)  

upsInfoSerial 1.3.6.1.4.1.6574.4.2.7
UPS serial number
OBJECT-TYPE    
  DisplayString Size(0..31)  

upsInfoVendorID 1.3.6.1.4.1.6574.4.2.8
Vendor ID for USB devices
OBJECT-TYPE    
  DisplayString Size(0..31)  

upsInfoProductID 1.3.6.1.4.1.6574.4.2.9
Product ID for USB devices
OBJECT-TYPE    
  DisplayString Size(0..31)  

upsInfoFirmware 1.3.6.1.4.1.6574.4.2.10
OBJECT IDENTIFIER    

upsInfoFirmwareName 1.3.6.1.4.1.6574.4.2.10.1
UPS firmware
OBJECT-TYPE    
  DisplayString Size(0..31)  

upsInfoFirmwareAux 1.3.6.1.4.1.6574.4.2.10.2
Auxiliary device firmware
OBJECT-TYPE    
  DisplayString Size(0..31)  

upsInfoTemperature 1.3.6.1.4.1.6574.4.2.11
UPS temperature (degrees C)
OBJECT-TYPE    
  Float  

upsInfoLoad 1.3.6.1.4.1.6574.4.2.12
OBJECT IDENTIFIER    

upsInfoLoadValue 1.3.6.1.4.1.6574.4.2.12.1
Load on UPS (percent)
OBJECT-TYPE    
  Float  

upsInfoLoadHigh 1.3.6.1.4.1.6574.4.2.12.2
Load when UPS switches to overload condition (OVER) (percent)
OBJECT-TYPE    
  Float  

upsInfoID 1.3.6.1.4.1.6574.4.2.13
UPS system identifier
OBJECT-TYPE    
  DisplayString Size(0..31)  

upsInfoDelay 1.3.6.1.4.1.6574.4.2.14
OBJECT IDENTIFIER    

upsInfoDelayStart 1.3.6.1.4.1.6574.4.2.14.1
Interval to wait before restarting the load (seconds)
OBJECT-TYPE    
  NonNegativeInteger  

upsInfoDelayReboot 1.3.6.1.4.1.6574.4.2.14.2
Interval to wait before rebooting the UPS (seconds)
OBJECT-TYPE    
  NonNegativeInteger  

upsInfoDelayShutdown 1.3.6.1.4.1.6574.4.2.14.3
Interval to wait after shutdown with delay command (seconds)
OBJECT-TYPE    
  NonNegativeInteger  

upsInfoTimer 1.3.6.1.4.1.6574.4.2.15
OBJECT IDENTIFIER    

upsInfoTimerStart 1.3.6.1.4.1.6574.4.2.15.1
Time before the load will be started (seconds)
OBJECT-TYPE    
  NonNegativeInteger  

upsInfoTimerReboot 1.3.6.1.4.1.6574.4.2.15.2
Time before the load will be rebooted (seconds)
OBJECT-TYPE    
  NonNegativeInteger  

upsInfoTimerShutdown 1.3.6.1.4.1.6574.4.2.15.3
Time before the load will be shutdown (seconds)
OBJECT-TYPE    
  NonNegativeInteger  

upsInfoTest 1.3.6.1.4.1.6574.4.2.16
OBJECT IDENTIFIER    

upsInfoTestInterval 1.3.6.1.4.1.6574.4.2.16.1
Interval between self tests
OBJECT-TYPE    
  NonNegativeInteger  

upsInfoTestResult 1.3.6.1.4.1.6574.4.2.16.2
Results of last self test
OBJECT-TYPE    
  DisplayString Size(0..31)  

upsInfoDisplayLanguage 1.3.6.1.4.1.6574.4.2.17
Language to use on front panel
OBJECT-TYPE    
  DisplayString Size(0..31)  

upsInfoContacts 1.3.6.1.4.1.6574.4.2.18
UPS external contact sensors
OBJECT-TYPE    
  DisplayString Size(0..31)  

upsInfoEffciency 1.3.6.1.4.1.6574.4.2.19
Efficiency of the UPS (ratio of the output current on the input current) (percent)
OBJECT-TYPE    
  NonNegativeInteger  

upsInfoPower 1.3.6.1.4.1.6574.4.2.20
OBJECT IDENTIFIER    

upsInfoPowerValue 1.3.6.1.4.1.6574.4.2.20.1
Current value of apparent power (Volt-Amps)
OBJECT-TYPE    
  Float  

upsInfoPowerNominal 1.3.6.1.4.1.6574.4.2.20.2
Nominal value of apparent power (Volt-Amps)
OBJECT-TYPE    
  Float  

upsInfoRealPower 1.3.6.1.4.1.6574.4.2.21
OBJECT IDENTIFIER    

upsInfoRealPowerValue 1.3.6.1.4.1.6574.4.2.21.1
Current value of real power (Watts)
OBJECT-TYPE    
  Float  

upsInfoRealPowerNominal 1.3.6.1.4.1.6574.4.2.21.2
Nominal value of real power (Watts)
OBJECT-TYPE    
  Float  

upsInfoBeeperStatus 1.3.6.1.4.1.6574.4.2.22
UPS beeper status (enabled, disabled or muted)
OBJECT-TYPE    
  DisplayString Size(0..31)  

upsInfoType 1.3.6.1.4.1.6574.4.2.23
UPS type
OBJECT-TYPE    
  DisplayString Size(0..31)  

upsInfoWatchdogStatus 1.3.6.1.4.1.6574.4.2.24
UPS watchdog status (enabled or disabled)
OBJECT-TYPE    
  DisplayString Size(0..31)  

upsInfoStart 1.3.6.1.4.1.6574.4.2.25
OBJECT IDENTIFIER    

upsInfoStartAuto 1.3.6.1.4.1.6574.4.2.25.1
UPS starts when mains is (re)applied
OBJECT-TYPE    
  DisplayString Size(0..31)  

upsInfoStartBattery 1.3.6.1.4.1.6574.4.2.25.2
Allow to start UPS from battery
OBJECT-TYPE    
  DisplayString Size(0..31)  

upsInfoStartReboot 1.3.6.1.4.1.6574.4.2.25.3
UPS coldstarts from battery (enabled or disabled)
OBJECT-TYPE    
  DisplayString Size(0..31)  

upsBattery 1.3.6.1.4.1.6574.4.3
OBJECT IDENTIFIER    

upsBatteryCharge 1.3.6.1.4.1.6574.4.3.1
OBJECT IDENTIFIER    

upsBatteryChargeValue 1.3.6.1.4.1.6574.4.3.1.1
Battery charge
OBJECT-TYPE    
  Float  

upsBatteryChargeLow 1.3.6.1.4.1.6574.4.3.1.2
Remaining battery level when UPS switches to LB (percent)
OBJECT-TYPE    
  Float  

upsBatteryChargeRestart 1.3.6.1.4.1.6574.4.3.1.3
Minimum battery level for UPS restart after power-off
OBJECT-TYPE    
  Float  

upsBatteryChargeWarning 1.3.6.1.4.1.6574.4.3.1.4
Battery level when UPS switches to Warning state (percent)
OBJECT-TYPE    
  Float  

upsBatteryVoltage 1.3.6.1.4.1.6574.4.3.2
OBJECT IDENTIFIER    

upsBatteryVoltageValue 1.3.6.1.4.1.6574.4.3.2.1
The magnitude of the present battery voltage.
OBJECT-TYPE    
  Float  

upsBatteryVoltageNominal 1.3.6.1.4.1.6574.4.3.2.2
Nominal battery voltage.
OBJECT-TYPE    
  Float  

upsBatteryVoltageLow 1.3.6.1.4.1.6574.4.3.2.3
Minimum battery voltage, that triggers FSD status .
OBJECT-TYPE    
  Float  

upsBatteryVoltageHigh 1.3.6.1.4.1.6574.4.3.2.4
Maximum battery voltage (Ie battery.charge = 100).
OBJECT-TYPE    
  Float  

upsBatteryCapacity 1.3.6.1.4.1.6574.4.3.3
Battery capacity (Ah)
OBJECT-TYPE    
  Float  

upsBatteryCurrent 1.3.6.1.4.1.6574.4.3.4
The present battery current.
OBJECT-TYPE    
  Float  

upsBatteryTemperature 1.3.6.1.4.1.6574.4.3.5
The ambient temperature at or near the UPS Battery casing.
OBJECT-TYPE    
  Float  

upsBatteryRuntime 1.3.6.1.4.1.6574.4.3.6
OBJECT IDENTIFIER    

upsBatteryRuntimeValue 1.3.6.1.4.1.6574.4.3.6.1
Battery runtime (seconds)
OBJECT-TYPE    
  NonNegativeInteger  

upsBatteryRuntimeLow 1.3.6.1.4.1.6574.4.3.6.2
Remaining battery runtime when UPS switches to LB (seconds)
OBJECT-TYPE    
  NonNegativeInteger  

upsBatteryRuntimeRestart 1.3.6.1.4.1.6574.4.3.6.3
Minimum battery runtime for UPS restart after power-off (seconds)
OBJECT-TYPE    
  NonNegativeInteger  

upsBatteryAlarmThreshold 1.3.6.1.4.1.6574.4.3.7
Battery alarm threshold
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsBatteryDate 1.3.6.1.4.1.6574.4.3.8
Battery change date
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsBatteryMfrDate 1.3.6.1.4.1.6574.4.3.9
Battery manufacturing date
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsBatteryPacks 1.3.6.1.4.1.6574.4.3.10
Number of battery packs
OBJECT-TYPE    
  NonNegativeInteger  

upsBatteryPacksBad 1.3.6.1.4.1.6574.4.3.11
Number of bad battery packs
OBJECT-TYPE    
  NonNegativeInteger  

upsBatteryType 1.3.6.1.4.1.6574.4.3.12
Battery chemistry
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsBatteryProtection 1.3.6.1.4.1.6574.4.3.13
Prevent deep discharge of battery
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsBatteryEnergySave 1.3.6.1.4.1.6574.4.3.14
Switch off when running on battery and no/low load
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsInput 1.3.6.1.4.1.6574.4.4
OBJECT IDENTIFIER    

upsInputVoltage 1.3.6.1.4.1.6574.4.4.1
OBJECT IDENTIFIER    

upsInputVoltageValue 1.3.6.1.4.1.6574.4.4.1.1
Input voltage
OBJECT-TYPE    
  Float  

upsInputVoltageMax 1.3.6.1.4.1.6574.4.4.1.2
Maximum incoming voltage seen
OBJECT-TYPE    
  Float  

upsInputVoltageMin 1.3.6.1.4.1.6574.4.4.1.3
Minimum incoming voltage seen
OBJECT-TYPE    
  Float  

upsInputVoltageNominal 1.3.6.1.4.1.6574.4.4.1.4
Nominal input voltage
OBJECT-TYPE    
  Float  

upsInputVoltageExtend 1.3.6.1.4.1.6574.4.4.1.5
Extended input voltage range
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsInputVoltageFault 1.3.6.1.4.1.6574.4.4.1.6
Input voltage Fault
OBJECT-TYPE    
  Float  

upsInputTransfer 1.3.6.1.4.1.6574.4.4.2
OBJECT IDENTIFIER    

upsInputTransferReason 1.3.6.1.4.1.6574.4.4.2.1
Reason for last transfer to battery
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsInputTransferLow 1.3.6.1.4.1.6574.4.4.2.2
Low voltage transfer point
OBJECT-TYPE    
  Float  

upsInputTransferHigh 1.3.6.1.4.1.6574.4.4.2.3
High voltage transfer point
OBJECT-TYPE    
  Float  

upsInputTransferLowMin 1.3.6.1.4.1.6574.4.4.2.4
smallest settable low voltage transfer point
OBJECT-TYPE    
  Float  

upsInputTransferLowMax 1.3.6.1.4.1.6574.4.4.2.5
greatest settable low voltage transfer point
OBJECT-TYPE    
  Float  

upsInputTransferHighMin 1.3.6.1.4.1.6574.4.4.2.6
smallest settable high voltage transfer point
OBJECT-TYPE    
  Float  

upsInputTransferHighMax 1.3.6.1.4.1.6574.4.4.2.7
greatest settable high voltage transfer point
OBJECT-TYPE    
  Float  

upsInputTransferBoostLow 1.3.6.1.4.1.6574.4.4.2.8
Low voltage boosting transfer point
OBJECT-TYPE    
  Float  

upsInputTransferBoostHigh 1.3.6.1.4.1.6574.4.4.2.9
High voltage boosting transfer point
OBJECT-TYPE    
  Float  

upsInputTransferTrimLow 1.3.6.1.4.1.6574.4.4.2.10
Low voltage trimming transfer point
OBJECT-TYPE    
  Float  

upsInputTransferTrimHigh 1.3.6.1.4.1.6574.4.4.2.11
High voltage trimming transfer point
OBJECT-TYPE    
  Float  

upsInputSensitivity 1.3.6.1.4.1.6574.4.4.3
Input power sensitivity
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsInputQuality 1.3.6.1.4.1.6574.4.4.4
Input power quality
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsInputCurrent 1.3.6.1.4.1.6574.4.4.5
OBJECT IDENTIFIER    

upsInputCurrentValue 1.3.6.1.4.1.6574.4.4.5.1
Input current (A)
OBJECT-TYPE    
  Float  

upsInputCurrentNominal 1.3.6.1.4.1.6574.4.4.5.2
Nominal input current (A)
OBJECT-TYPE    
  Float  

upsInputFrequency 1.3.6.1.4.1.6574.4.4.6
OBJECT IDENTIFIER    

upsInputFrequencyValue 1.3.6.1.4.1.6574.4.4.6.1
Input line frequency (Hz)
OBJECT-TYPE    
  Float  

upsInputFrequencyNominal 1.3.6.1.4.1.6574.4.4.6.2
Nominal input line frequency (Hz)
OBJECT-TYPE    
  Float  

upsInputFrequencyLow 1.3.6.1.4.1.6574.4.4.6.3
Input line frequency low (Hz)
OBJECT-TYPE    
  Float  

upsInputFrequencyHigh 1.3.6.1.4.1.6574.4.4.6.4
Input line frequency high (Hz)
OBJECT-TYPE    
  Float  

upsInputFrequencyExtend 1.3.6.1.4.1.6574.4.4.6.5
Extended input frequency range
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsOutput 1.3.6.1.4.1.6574.4.5
OBJECT IDENTIFIER    

upsOutputVoltage 1.3.6.1.4.1.6574.4.5.1
OBJECT IDENTIFIER    

upsOutputVoltageValue 1.3.6.1.4.1.6574.4.5.1.1
Output voltage (V)
OBJECT-TYPE    
  Float  

upsOutputVoltageNominal 1.3.6.1.4.1.6574.4.5.1.2
Nominal output voltage (V)
OBJECT-TYPE    
  Float  

upsOutputFrequency 1.3.6.1.4.1.6574.4.5.2
OBJECT IDENTIFIER    

upsOutputFrequencyValue 1.3.6.1.4.1.6574.4.5.2.1
Output frequency (Hz)
OBJECT-TYPE    
  Float  

upsOutputFrequencyNominal 1.3.6.1.4.1.6574.4.5.2.2
Nominal output frequency (Hz)
OBJECT-TYPE    
  Float  

upsOutputCurrent 1.3.6.1.4.1.6574.4.5.3
OBJECT IDENTIFIER    

upsOutputCurrentValue 1.3.6.1.4.1.6574.4.5.3.1
Output current (A)
OBJECT-TYPE    
  Float  

upsOutputCurrentNominal 1.3.6.1.4.1.6574.4.5.3.2
Nominal output current (A)
OBJECT-TYPE    
  Float  

upsAmbient 1.3.6.1.4.1.6574.4.6
OBJECT IDENTIFIER    

upsAmbientTemperature 1.3.6.1.4.1.6574.4.6.1
OBJECT IDENTIFIER    

upsAmbientTemperatureValue 1.3.6.1.4.1.6574.4.6.1.1
Ambient temperature (degrees C)
OBJECT-TYPE    
  Float  

upsAmbientTemperatureAlarm 1.3.6.1.4.1.6574.4.6.1.2
Temperature alarm (enabled/disabled)
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsAmbientTemperatureHigh 1.3.6.1.4.1.6574.4.6.1.3
Temperature threshold high (degrees C)
OBJECT-TYPE    
  Float  

upsAmbientTemperatureLow 1.3.6.1.4.1.6574.4.6.1.4
Temperature threshold low (degrees C)
OBJECT-TYPE    
  Float  

upsAmbientTemperatureMax 1.3.6.1.4.1.6574.4.6.1.5
Maximum temperature seen (degrees C)
OBJECT-TYPE    
  Float  

upsAmbientTemperatureMin 1.3.6.1.4.1.6574.4.6.1.6
Minimum temperature seen (degrees C)
OBJECT-TYPE    
  Float  

upsAmbientHumidity 1.3.6.1.4.1.6574.4.6.2
OBJECT IDENTIFIER    

upsAmbientHumidityValue 1.3.6.1.4.1.6574.4.6.2.1
Ambient relative humidity (percent)
OBJECT-TYPE    
  Float  

upsAmbientHumidityAlarm 1.3.6.1.4.1.6574.4.6.2.2
Relative humidity alarm (enabled/disabled)
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsAmbientHumidityHigh 1.3.6.1.4.1.6574.4.6.2.3
Relative humidity threshold high (percent)
OBJECT-TYPE    
  Float  

upsAmbientHumidityLow 1.3.6.1.4.1.6574.4.6.2.4
Relative humidity threshold low (percent)
OBJECT-TYPE    
  Float  

upsAmbientHumidityMax 1.3.6.1.4.1.6574.4.6.2.5
Maximum relative humidity seen (percent)
OBJECT-TYPE    
  Float  

upsAmbientHumidityMin 1.3.6.1.4.1.6574.4.6.2.6
Minimum relative humidity seen (percent)
OBJECT-TYPE    
  Float  

upsDriver 1.3.6.1.4.1.6574.4.7
OBJECT IDENTIFIER    

upsDriverName 1.3.6.1.4.1.6574.4.7.1
Driver name
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsDriverVersion 1.3.6.1.4.1.6574.4.7.2
Driver version (NUT release)
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsDriverVersionData 1.3.6.1.4.1.6574.4.7.3
Driver version data
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsDriverVersionInternal 1.3.6.1.4.1.6574.4.7.4
Internal driver version (if tracked separately)
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsDriverPollInterval 1.3.6.1.4.1.6574.4.7.5
Poll interval setup in configuration file
OBJECT-TYPE    
  Integer32  

upsDriverPort 1.3.6.1.4.1.6574.4.7.6
Port setup in configuration file
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsDriverPollFrequency 1.3.6.1.4.1.6574.4.7.7
Poll frequency
OBJECT-TYPE    
  Integer32  

upsDriverProductID 1.3.6.1.4.1.6574.4.7.8
Product ID
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsDriverSnmpVersion 1.3.6.1.4.1.6574.4.7.9
Snmp version
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsServer 1.3.6.1.4.1.6574.4.8
OBJECT IDENTIFIER    

upsServerInfo 1.3.6.1.4.1.6574.4.8.1
Server information
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsServerVersion 1.3.6.1.4.1.6574.4.8.2
Server version
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsConformance 1.3.6.1.4.1.6574.4.9
OBJECT IDENTIFIER    

upsCompliances 1.3.6.1.4.1.6574.4.9.1
OBJECT IDENTIFIER    

upsGroups 1.3.6.1.4.1.6574.4.9.2
OBJECT IDENTIFIER    

upsCompliance 1.3.6.1.4.1.6574.4.9.1.1
The compliance statement for synoSystem entities which implement the SYNOLOGY SYSTEM MIB.
MODULE-COMPLIANCE    

upsGroup 1.3.6.1.4.1.6574.4.9.2.1
A collection of objects providing basic information of an synology ups entity.
OBJECT-GROUP