SWITCH-SYSTEM-MIB

File: SWITCH-SYSTEM-MIB.mib (61274 bytes)

Imported modules

SNMPv2-SMI	SNMPv2-TC	SNMPv2-CONF
RAISECOM-BASE-MIB	IF-MIB	SWITCH-TC

Imported symbols

MODULE-IDENTITY	OBJECT-TYPE	Integer32
Counter32	NOTIFICATION-TYPE	MacAddress
RowStatus	TruthValue	OBJECT-GROUP
iscomSwitch	ifIndex	PortList
EnableVar	Vlanset

Defined Types

RcSlotStateEntry
SEQUENCE
	rcSlotIndex	INTEGER
	rcSlotPortStart	INTEGER
	rcSlotPortNum	INTEGER
	rcSlotType	INTEGER

RcPortEntry
SEQUENCE
	rcPortIndex	Integer32
	rcPortType	INTEGER
	rcSlotTableIndex	INTEGER
	rcSlotPortIndex	INTEGER
	rcPortAdminStatus	INTEGER
	rcPortOperStatus	INTEGER
	rcPortDuplexSpeedSet	INTEGER
	rcPortDuplexSpeedGet	INTEGER
	rcPortFlowControlEnable	EnableVar
	rcPortMacLearningEnable	EnableVar
	rcPortMacThreshold	INTEGER
	rcPortStormControlBcastEnable	EnableVar
	rcPortStormControlMcastEnable	EnableVar
	rcPortStormControlDlfEnable	EnableVar
	rcPortStormControlBurst	INTEGER
	rcPortStormControlLimit	INTEGER
	rcPortStormControlLimitRatio	INTEGER
	rcPortDefaultPriority	INTEGER
	rcPortLoopbackDetectEnable	EnableVar
	rcPortLoopbackDetectSrcPort	INTEGER
	rcPortProtected	EnableVar
	rcPortFlowControlRecvEnable	EnableVar
	rcPortFlowControlSendEnable	EnableVar
	rcPortFlowControlRecvStatus	EnableVar
	rcPortFlowControlSendStatus	EnableVar
	rcPortLoopbackDetectDownTime	INTEGER
	rcPortMediaAttachType	INTEGER
	rcPortMediaAttachCapability	INTEGER
	rcPortMDIXMode	INTEGER
	rcPortMDIXStatus	INTEGER
	rcportDiscPKts	Counter32
	rcPortMacThresholdVlan	INTEGER
	rcPortPhysicalStatus	INTEGER
	rcPortLinkUpDelayTime	INTEGER

RcComboPortEntry
SEQUENCE
	rcComboIndex	INTEGER
	rcComboPortIndex	INTEGER
	rcComboPortType	INTEGER
	rcComboPortMediaAttachType	INTEGER
	rcComboPortActiveStatus	INTEGER
	rcComboPortMediaAttachCapability	INTEGER

RcPortStormControlEntry
SEQUENCE
	rcPortStormControlPortIndex	INTEGER
	rcPortStormControlPktType	INTEGER
	rcPortStormControlUnit	INTEGER
	rcPortStormControlMaxValue	INTEGER

RcUspPortToUspMappingEntry
SEQUENCE
	rcUspPortToUspMappingUnitIndex	INTEGER
	rcUspPortToUspMappingSlotIndex	INTEGER
	rcUspPortToUspMappingPortIndex	INTEGER

RcUspUspToPortMappingEntry
SEQUENCE
	rcUspUspToPortMappingUnitIndex	INTEGER
	rcUspUspToPortMappingSlotIndex	INTEGER
	rcUspUspToPortMappingPortIndex	INTEGER
	rcUspPortIndex	INTEGER

RcUspUnitEntry
SEQUENCE
	rcUspUnitIndex	INTEGER
	rcUspUnitSlotNum	INTEGER
	rcUspUnitPortNum	INTEGER

RcUspSlotEntry
SEQUENCE
	rcUspSlotUnitIndex	INTEGER
	rcUspSlotSlotIndex	INTEGER
	rcUspSlotSlotType	INTEGER
	rcUspSlotRightSubcardType	INTEGER
	rcUspSlotActualSubcardType	INTEGER
	rcUspSlotSerial	OCTET STRING
	rcUspSlotHardVersion	OCTET STRING
	rcUspSlotSoftwareVersion	OCTET STRING
	rcUspSlotPortStart	INTEGER
	rcUspSlotPortNum	INTEGER
	rcUspSlotSlotState	INTEGER

RcUspIfToUspMappingEntry
SEQUENCE
	rcUspIfToUspMappingUnitIndex	INTEGER
	rcUspIfToUspMappingSlotIndex	INTEGER
	rcUspIfToUspMappingPortIndex	INTEGER
	rcUspIfType	INTEGER
	rcUspIfState	INTEGER

RcUspUspToIfMappingEntry
SEQUENCE
	rcUspUspToIfMappingUnitIndex	INTEGER
	rcUspUspToIfMappingSlotIndex	INTEGER
	rcUspUspToIfMappingPortIndex	INTEGER
	rcUspIfTypeIndex	INTEGER
	rcUspIfIndex	INTEGER

Defined Values

rcSystem		1.3.6.1.4.1.8886.6.1.1
iscom switch system Enterprise MIB definition.
MODULE-IDENTITY

rcSwitchInformation		1.3.6.1.4.1.8886.6.1.1.1
OBJECT IDENTIFIER

rcSlotInformation		1.3.6.1.4.1.8886.6.1.1.2
OBJECT IDENTIFIER

rcSwitchConfig		1.3.6.1.4.1.8886.6.1.1.3
OBJECT IDENTIFIER

rcPortInfoConfig		1.3.6.1.4.1.8886.6.1.1.4
OBJECT IDENTIFIER

rcLoopbackTrap		1.3.6.1.4.1.8886.6.1.1.5
OBJECT IDENTIFIER

rcPorConnectorChangeTrap		1.3.6.1.4.1.8886.6.1.1.6
OBJECT IDENTIFIER

rcPortMappingInfoConfig		1.3.6.1.4.1.8886.6.1.1.8
OBJECT IDENTIFIER

rcSwitchRoseVersion		1.3.6.1.4.1.8886.6.1.1.1.1
rose software version .
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

rcSwitchHardwareVersion		1.3.6.1.4.1.8886.6.1.1.1.2
rose hardware version .
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

rcSwitchServiceInfo		1.3.6.1.4.1.8886.6.1.1.1.3
rose software service information version . every bit stand for one type of service and , '0' stand for service is up, '1' stand for not start Qos-- bit(0) Filter -- bit(1) Storm control -- bit(2) Authentication-- bit(3) IGMP Snooping-- bit(4) STP-- bit(5) RIP-- bit(6) OSPF-- bit(7) PIM-DM-- bit(8) PIM-SM-- bit(9) ....
Status: deprecated	Access: read-only
OBJECT-TYPE
	Integer32

rcSwitchLastErrorCode		1.3.6.1.4.1.8886.6.1.1.1.4
This mib object stand for system last error code ,for system analysis 0 for no error 1 ...0x7fffffff for error code
Status: deprecated	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

rcSwitchMaxPhysicalPortNum		1.3.6.1.4.1.8886.6.1.1.1.5
The physical port number which system supports.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

rcSwitchMaxAggregationPortNum		1.3.6.1.4.1.8886.6.1.1.1.6
The aggregation port number which system supports.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

rcSwitchMaxL3IpSubnetNum		1.3.6.1.4.1.8886.6.1.1.1.7
The layer 3 port number which system supports.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

rcSwitchMacTableCapability		1.3.6.1.4.1.8886.6.1.1.1.8
The capability of MAC table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcSwitchMacAddress		1.3.6.1.4.1.8886.6.1.1.1.9
MAC address.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

rcSwitchVlanSpaceSize		1.3.6.1.4.1.8886.6.1.1.1.10
the number of vlans in a vlan
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

rcSwitchPvidSpaceSize		1.3.6.1.4.1.8886.6.1.1.1.11
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

rcSwitchDefaultVlan		1.3.6.1.4.1.8886.6.1.1.1.12
Default vlan
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

rcSwitchBootstrapVersion		1.3.6.1.4.1.8886.6.1.1.1.13
rose bootstrap version .
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

rcSwitchSerialNumber		1.3.6.1.4.1.8886.6.1.1.1.14
The serial number of the motherboard.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

rcSwitchFpgaVersion		1.3.6.1.4.1.8886.6.1.1.1.15
rose fpga version.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

rcSwitchProductVersion		1.3.6.1.4.1.8886.6.1.1.1.16
product version
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

rcSwitchCmpAbName		1.3.6.1.4.1.8886.6.1.1.1.17
manufacturer abbreviated name
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

rcSwitchCmpFullName		1.3.6.1.4.1.8886.6.1.1.1.18
manufacturer full name
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

rcSwitchDeviceName		1.3.6.1.4.1.8886.6.1.1.1.19
device name
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

rcSwitchBackBoardVendorName		1.3.6.1.4.1.8886.6.1.1.1.20
Backboard vendor name.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

rcSwitchBackBoardSerialNumber		1.3.6.1.4.1.8886.6.1.1.1.21
Serial number of the backboard.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

rcSwitchBackBoardName		1.3.6.1.4.1.8886.6.1.1.1.22
Backboard name.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

rcSwitchBackBoardVersion		1.3.6.1.4.1.8886.6.1.1.1.23
Backboard version.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

rcSlotNum		1.3.6.1.4.1.8886.6.1.1.2.1
Total number of slot
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

rcSlotStateTable		1.3.6.1.4.1.8886.6.1.1.2.2
A table of slot .
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcSlotStateEntry

rcSlotStateEntry		1.3.6.1.4.1.8886.6.1.1.2.2.1
A list of slot.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcSlotStateEntry

rcSlotIndex		1.3.6.1.4.1.8886.6.1.1.2.2.1.1
slot index based 0
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER

rcSlotPortStart		1.3.6.1.4.1.8886.6.1.1.2.2.1.2
the start number of port in this slot
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

rcSlotPortNum		1.3.6.1.4.1.8886.6.1.1.2.2.1.3
the number of ports in this slot
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

rcSlotType		1.3.6.1.4.1.8886.6.1.1.2.2.1.4
slot type
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	inexistence(0), fx-DulMode-1000M(1), tx-1000M(2), fx-SigMode-1000M(3), fx-DulMode-100M(4), fx-SigMode-100M(5), tx-100M(6), px-1000M(7)

rcMacAgingTime		1.3.6.1.4.1.8886.6.1.1.3.1
The value based 10 is the aging time for MAC address. Aging will be disable when aging time was (0)
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..2147483647

rcStormControlBcastEnable		1.3.6.1.4.1.8886.6.1.1.3.2
Set the Storm control for broadcast on the interface to enable(1) or disable(2).
Status: mandatory	Access: read-write
OBJECT-TYPE
	EnableVar

rcStormControlMcastEnable		1.3.6.1.4.1.8886.6.1.1.3.3
Set the Storm control for multicast on the interface to enable(1) or disable(2).
Status: mandatory	Access: read-write
OBJECT-TYPE
	EnableVar

rcStormControlDlfEnable		1.3.6.1.4.1.8886.6.1.1.3.4
Set the Storm control for DLF on the interface to enable(1) or disable(2).
Status: mandatory	Access: read-write
OBJECT-TYPE
	EnableVar

rcStormControlpps		1.3.6.1.4.1.8886.6.1.1.3.5
The limit number for storm control on the interface .
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..262143

rcStormControlbps		1.3.6.1.4.1.8886.6.1.1.3.6
The limit number for storm control on the interface .
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..1073741823

rcStormControlRatio		1.3.6.1.4.1.8886.6.1.1.3.7
storm control limit ratio
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..100

rcStormControlBurst		1.3.6.1.4.1.8886.6.1.1.3.8
Set burst length when storm control open on the interface. .
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..512

rcStpEnable		1.3.6.1.4.1.8886.6.1.1.3.9
The enabled/disabled status of STP for the bridge entity.
Status: mandatory	Access: read-write
OBJECT-TYPE
	EnableVar

rcSvlEnable		1.3.6.1.4.1.8886.6.1.1.3.10
share vlan mode enable or disable
Status: mandatory	Access: read-write
OBJECT-TYPE
	EnableVar

rcGarpEnable		1.3.6.1.4.1.8886.6.1.1.3.11
GARP enable or disable
Status: mandatory	Access: read-write
OBJECT-TYPE
	EnableVar

rcLacpEnable		1.3.6.1.4.1.8886.6.1.1.3.12
share vlan mode enable or disable
Status: mandatory	Access: read-write
OBJECT-TYPE
	EnableVar

rcVlanSpaceNum		1.3.6.1.4.1.8886.6.1.1.3.13
The system supports at most rcVlanSpaceSize vlans, so the vlan ID increases at rcVlanSpaceSize step over.
Status: obsolete	Access: read-write
OBJECT-TYPE
	INTEGER	0..4093

rcPvidSpaceNum		1.3.6.1.4.1.8886.6.1.1.3.14
The system supports at most rcPvidSpaceSize vlans, so the vlan ID increases at rcPvidSpaceSize step over.
Status: obsolete	Access: read-write
OBJECT-TYPE
	INTEGER	0..4093

rcLoopbackDetectInterval		1.3.6.1.4.1.8886.6.1.1.3.15
Interval of sending loopback-detect packet.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..65535

rcArpAgingTime		1.3.6.1.4.1.8886.6.1.1.3.16
arp timeout
Status: deprecated	Access: read-write
OBJECT-TYPE
	Integer32	0..2147483647

rcBpduTransPorts		1.3.6.1.4.1.8886.6.1.1.3.17
The ports translating BPDU packets.
Status: current	Access: read-write
OBJECT-TYPE
	PortList

rcDot1xTransPorts		1.3.6.1.4.1.8886.6.1.1.3.18
The ports translating Dot1x packets.
Status: current	Access: read-write
OBJECT-TYPE
	PortList

rcLacpTransPorts		1.3.6.1.4.1.8886.6.1.1.3.19
The ports translating Lacp packets.
Status: current	Access: read-write
OBJECT-TYPE
	PortList

rcGarpTransPorts		1.3.6.1.4.1.8886.6.1.1.3.20
The ports translating Garp packets.
Status: current	Access: read-write
OBJECT-TYPE
	PortList

rcGmrpTransPorts		1.3.6.1.4.1.8886.6.1.1.3.21
The ports translating Gmrp packets.
Status: current	Access: read-write
OBJECT-TYPE
	PortList

rcGvrpTransPorts		1.3.6.1.4.1.8886.6.1.1.3.22
The ports translating Gvrp packets.
Status: current	Access: read-write
OBJECT-TYPE
	PortList

rcIpRouting		1.3.6.1.4.1.8886.6.1.1.3.23
start or stop system routing function . this is a commnd MIB variable .
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	startIpRouting(1), stopIpRouting(2)

rcStaticRouteDistance		1.3.6.1.4.1.8886.6.1.1.3.24
system static route distance value . this is a commnd MIB variable .
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..255

rcFastRoute		1.3.6.1.4.1.8886.6.1.1.3.25
true for fast route and false for normal route .
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rcDlfForwardingEnable		1.3.6.1.4.1.8886.6.1.1.3.26
whether forwarding DLF packets .
Status: mandatory	Access: read-write
OBJECT-TYPE
	EnableVar

rcLoopbackDetectVlan		1.3.6.1.4.1.8886.6.1.1.3.27
loopback-detection packet belongs to which VLAN.
Status: mandatory	Access: read-write
OBJECT-TYPE
	Integer32	1..4094

rcLoopbackDetectDestAddr		1.3.6.1.4.1.8886.6.1.1.3.28
destination MAC address of loopback-detection packet.
Status: mandatory	Access: read-write
OBJECT-TYPE
	MacAddress

rcMaxAllowedFrameLength		1.3.6.1.4.1.8886.6.1.1.3.29
the maximum packet size for the switch.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1500..65535

rcSvlDefaultVlan		1.3.6.1.4.1.8886.6.1.1.3.30
default vlan which the mac address is also learned to.
Status: mandatory	Access: read-write
OBJECT-TYPE
	Integer32	1..4094

rcTelnetMaxSessions		1.3.6.1.4.1.8886.6.1.1.3.31
Max sessions device telnet server permits. '0' indicates that device won't permits any telnet connect.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..5

rcTelnetAcceptPorts		1.3.6.1.4.1.8886.6.1.1.3.32
Ports that access telnet connect request to telnet server on device.
Status: current	Access: read-write
OBJECT-TYPE
	PortList

rcVlanMacLearning		1.3.6.1.4.1.8886.6.1.1.3.33
Enable or disable source MAC address learning on VLAN.
Status: current	Access: read-write
OBJECT-TYPE
	Vlanset

rcConsoleEnable		1.3.6.1.4.1.8886.6.1.1.3.34
Enable or disable console connect.
Status: current	Access: read-write
OBJECT-TYPE
	EnableVar

rcStormControlOperpps		1.3.6.1.4.1.8886.6.1.1.3.35
The actual limit number for storm control on the interface .
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..262143

rcStormControlOperbps		1.3.6.1.4.1.8886.6.1.1.3.36
The actual limit number for storm control on the interface .
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..1073741823

rcOperMaxAllowedFrameLength		1.3.6.1.4.1.8886.6.1.1.3.37
The actual maximum packet size for the switch.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1500..65535

rcTrapBindipEnable		1.3.6.1.4.1.8886.6.1.1.3.38
Enable or disable rapBindip.DEFVAL { disable }
Status: current	Access: read-write
OBJECT-TYPE
	EnableVar

rcPortTable		1.3.6.1.4.1.8886.6.1.1.4.1
A table of switch port and associated properties.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPortEntry

rcPortEntry		1.3.6.1.4.1.8886.6.1.1.4.1.1
Table entry for switch port control and status information.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPortEntry

rcPortIndex		1.3.6.1.4.1.8886.6.1.1.4.1.1.1
An index based 1 that uniquely identifies a system interface.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rcPortType		1.3.6.1.4.1.8886.6.1.1.4.1.1.2
port type,same as slot type.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	inexistence(0), fx-DulMode-1000M(1), tx-1000M(2), fx-SigMode-1000M(3), fx-DulMode-100M(4), fx-SigMode-100M(5), tx-100M(6), px-1000M(7)

rcSlotTableIndex		1.3.6.1.4.1.8886.6.1.1.4.1.1.3
the index of slot which this port is in.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

rcSlotPortIndex		1.3.6.1.4.1.8886.6.1.1.4.1.1.4
index of this port in the slot
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

rcPortAdminStatus		1.3.6.1.4.1.8886.6.1.1.4.1.1.5
The desired state of the interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	up(1), down(2)

rcPortOperStatus		1.3.6.1.4.1.8886.6.1.1.4.1.1.6
The current operational state of the interface.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2)

rcPortDuplexSpeedSet		1.3.6.1.4.1.8886.6.1.1.4.1.1.7
The desired speed and duplex for this interface. If the selected control is not possible on the interface, a value of illegal(99) is returned. If the port type does NOT support the default of autonegotiate(1), then the application initializes the port to a valid value (e.g., 1000full(6)). Note that not all controls are possible for all interfaces. For example, only full-1000(6) is available for Gigabit Ethernet interfaces.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	autonegotiate(1), half-10(2), full-10(3), half-100(4), full-100(5), half-1000(6), full-1000(7)

rcPortDuplexSpeedGet		1.3.6.1.4.1.8886.6.1.1.4.1.1.8
The actual speed and duplex for this interface. If the interface is not configured for an acceptable value, a value of illegal(99) is returned. A value of unknown(1) is returned when the 'rcPortLink' indicates down(2) for this interface.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), half-10(2), full-10(3), half-100(4), full-100(5), half-1000(6), full-1000(7), illegal(99)

rcPortFlowControlEnable		1.3.6.1.4.1.8886.6.1.1.4.1.1.9
Set the flow control on the interface to enable(1) or disable(2).
Status: mandatory	Access: read-write
OBJECT-TYPE
	EnableVar

rcPortMacLearningEnable		1.3.6.1.4.1.8886.6.1.1.4.1.1.10
Set the learning ability on the interface to enable(1) or disable(2).
Status: mandatory	Access: read-write
OBJECT-TYPE
	EnableVar

rcPortMacThreshold		1.3.6.1.4.1.8886.6.1.1.4.1.1.11
The Mac limit number on the interface or interface-vlan.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

rcPortStormControlBcastEnable		1.3.6.1.4.1.8886.6.1.1.4.1.1.12
Set the broadcast storm control on the interface to enable(1) or disable(2).
Status: mandatory	Access: read-write
OBJECT-TYPE
	EnableVar

rcPortStormControlMcastEnable		1.3.6.1.4.1.8886.6.1.1.4.1.1.13
Set the multicast storm control on the interface to enable(1) or disable(2).
Status: mandatory	Access: read-write
OBJECT-TYPE
	EnableVar

rcPortStormControlDlfEnable		1.3.6.1.4.1.8886.6.1.1.4.1.1.14
Set the DLF storm control on the interface to enable(1) or disable(2).
Status: mandatory	Access: read-write
OBJECT-TYPE
	EnableVar

rcPortStormControlBurst		1.3.6.1.4.1.8886.6.1.1.4.1.1.15
Set burst length when storm control open on the interface. .
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..512

rcPortStormControlLimit		1.3.6.1.4.1.8886.6.1.1.4.1.1.16
The limit number for storm control on this port .
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..2621430

rcPortStormControlLimitRatio		1.3.6.1.4.1.8886.6.1.1.4.1.1.17
storm control limit ratio on this port
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..100

rcPortDefaultPriority		1.3.6.1.4.1.8886.6.1.1.4.1.1.18
The received untaged frames are forwarded to a proper queue according to this default priority.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..8

rcPortLoopbackDetectEnable		1.3.6.1.4.1.8886.6.1.1.4.1.1.19
Loopback detect of this port is on or off.
Status: current	Access: read-write
OBJECT-TYPE
	EnableVar

rcPortLoopbackDetectSrcPort		1.3.6.1.4.1.8886.6.1.1.4.1.1.20
The source port(it sends loopback-detect packets) makes of loop with loopback port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

rcPortProtected		1.3.6.1.4.1.8886.6.1.1.4.1.1.21
Traffic between protected port group members are blocked.
Status: mandatory	Access: read-write
OBJECT-TYPE
	EnableVar

rcPortFlowControlRecvEnable		1.3.6.1.4.1.8886.6.1.1.4.1.1.22
Set the flow control on receive direction of the interface to enable(1) or disable(2).
Status: mandatory	Access: read-write
OBJECT-TYPE
	EnableVar

rcPortFlowControlSendEnable		1.3.6.1.4.1.8886.6.1.1.4.1.1.23
Set the flow control on sender direction of the interface to enable(1) or disable(2).
Status: mandatory	Access: read-write
OBJECT-TYPE
	EnableVar

rcPortFlowControlRecvStatus		1.3.6.1.4.1.8886.6.1.1.4.1.1.24
The flow control status on receive direction of the interface to enable(1) or disable(2).
Status: mandatory	Access: read-only
OBJECT-TYPE
	EnableVar

rcPortFlowControlSendStatus		1.3.6.1.4.1.8886.6.1.1.4.1.1.25
The flow control status on sender direction of the interface to enable(1) or disable(2).
Status: mandatory	Access: read-only
OBJECT-TYPE
	EnableVar

rcPortLoopbackDetectDownTime		1.3.6.1.4.1.8886.6.1.1.4.1.1.26
time of loopback port shutdown.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

rcPortMediaAttachType		1.3.6.1.4.1.8886.6.1.1.4.1.1.27
media attachment type of this Ether like interface.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	copper(1), fiber(2), card(3), sfp(4), combo-sfp(5), combo-copper(6)

rcPortMediaAttachCapability		1.3.6.1.4.1.8886.6.1.1.4.1.1.28
Medium type and capability of media attachment units. It is different with rcPortType which identifys the capability of the Ether like interface.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	inexistence(0), copper-1000M(1), copper-100M(2), fiber-1000M(3), fiber-100M(4), unlimited(5)

rcPortMDIXMode		1.3.6.1.4.1.8886.6.1.1.4.1.1.29
Automatic MDI Crossover mode of a port/PHY
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	normal(1), xover(2), auto(3)

rcPortMDIXStatus		1.3.6.1.4.1.8886.6.1.1.4.1.1.30
Automatic MDI Crossover mode of a port/PHY
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	normal(1), xover(2)

rcportDiscPKts		1.3.6.1.4.1.8886.6.1.1.4.1.1.31
The number of packets which were the difference between the total number of packets received on the interface and all packets transmitted out of the interface
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rcPortMacThresholdVlan		1.3.6.1.4.1.8886.6.1.1.4.1.1.32
when the Mac limits mac-thredshold on the interface-vlan, it indicates the VlanId;when the mac limits mac-thredshold on interface, its value is 4095.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..4095

rcPortPhysicalStatus		1.3.6.1.4.1.8886.6.1.1.4.1.1.33
The current physical state of the interface.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	up(1), down(2)

rcPortLinkUpDelayTime		1.3.6.1.4.1.8886.6.1.1.4.1.1.34
The port link delay time.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..60

rcComboPortTable		1.3.6.1.4.1.8886.6.1.1.4.2
A table of Combo port and associated properties.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcComboPortEntry

rcComboPortEntry		1.3.6.1.4.1.8886.6.1.1.4.2.1
Table entry for Combo port status information.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcComboPortEntry

rcComboIndex		1.3.6.1.4.1.8886.6.1.1.4.2.1.1
An index based 1 that uniquely identifies a Ether like interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER

rcComboPortIndex		1.3.6.1.4.1.8886.6.1.1.4.2.1.2
An index for media attachment on Combo that 'rcComboIndex' uniquely identifies a Ether like interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER

rcComboPortType		1.3.6.1.4.1.8886.6.1.1.4.2.1.3
port type identfies capability of Ether like interface.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	inexistence(0), fx-DulMode-1000M(1), tx-1000M(2), fx-SigMode-1000M(3), fx-DulMode-100M(4), fx-SigMode-100M(5), tx-100M(6)

rcComboPortMediaAttachType		1.3.6.1.4.1.8886.6.1.1.4.2.1.4
media attachment type of Combo port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	sfp(1), copper(2)

rcComboPortActiveStatus		1.3.6.1.4.1.8886.6.1.1.4.2.1.5
used to identify whether this Combo port currently be in the active state.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	active(1), inactive(2)

rcComboPortMediaAttachCapability		1.3.6.1.4.1.8886.6.1.1.4.2.1.6
Medium type and capability of media attachment units. It is different with rcComboPortType which identifys the capability of the Ether like interface
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	inexistence(0), copper-1000M(1), copper-100M(2), fiber-1000M(3), fiber-100M(4)

rcPortStormControlTable		1.3.6.1.4.1.8886.6.1.1.4.3
A table of ports' storm control properties.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcPortStormControlEntry

rcPortStormControlEntry		1.3.6.1.4.1.8886.6.1.1.4.3.1
Table entry for ports' storm control information.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcPortStormControlEntry

rcPortStormControlPortIndex		1.3.6.1.4.1.8886.6.1.1.4.3.1.1
An index based 1 that uniquely identifies a Ether like interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER

rcPortStormControlPktType		1.3.6.1.4.1.8886.6.1.1.4.3.1.2
An index that uniquely identifies packet type for storm control.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	broadcast(1), multicast(2), dlf(3)

rcPortStormControlUnit		1.3.6.1.4.1.8886.6.1.1.4.3.1.3
unit of value for storm control.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	pps(1), bps(2)

rcPortStormControlMaxValue		1.3.6.1.4.1.8886.6.1.1.4.3.1.4
Max value for storm control.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

rcLoopbackLinkUpTrap		1.3.6.1.4.1.8886.6.1.1.5.1
A linkDown trap signifies that the port identified by rcPortIndex change to link up state from link down.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcLoopbackLinkDownTrap		1.3.6.1.4.1.8886.6.1.1.5.2
A linkDown trap signifies that the port identified by rcPortIndex change to link down state from link up.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcPortConnectorInsertTrap		1.3.6.1.4.1.8886.6.1.1.6.1
To notify NMS that connector has been inserted. If 'rcPortMediaAttachType' is 'combo' NMS need check 'rcComboPortTable' for deciding which combo port is inserted.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcPortConnectorRemoveTrap		1.3.6.1.4.1.8886.6.1.1.6.2
To notify NMS that connector has been removed. If 'rcPortMediaAttachType' is 'combo' NMS need check 'rcComboPortTable' for deciding which combo port is removed.
Status: current	Access: read-write
NOTIFICATION-TYPE

rcUspPortToUspMappingTable		1.3.6.1.4.1.8886.6.1.1.8.1
The table describes how the port map to the USP.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcUspPortToUspMappingEntry

rcUspPortToUspMappingEntry		1.3.6.1.4.1.8886.6.1.1.8.1.1
Defines an entry in the rcUspPortToUspMappingTable.The index is rcPortIndex,while is unique in raisecom private mib.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcUspPortToUspMappingEntry

rcUspPortToUspMappingUnitIndex		1.3.6.1.4.1.8886.6.1.1.8.1.1.1
The unit index which port is mapped to.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

rcUspPortToUspMappingSlotIndex		1.3.6.1.4.1.8886.6.1.1.8.1.1.2
The slot index which port is mapped to.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

rcUspPortToUspMappingPortIndex		1.3.6.1.4.1.8886.6.1.1.8.1.1.3
The port index which port is mapped to.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

rcUspUspToPortMappingTable		1.3.6.1.4.1.8886.6.1.1.8.2
The table describes how the USP map to the port.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcUspUspToPortMappingEntry

rcUspUspToPortMappingEntry		1.3.6.1.4.1.8886.6.1.1.8.2.1
Defines an entry in the rcUspUspToPortMappingTable.The indexes are rcUspUspToPortMappingUnitIndex,rcUspUspToPortMappingSlotIndex and rcUspUspToPortMappingPortIndex.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcUspUspToPortMappingEntry

rcUspUspToPortMappingUnitIndex		1.3.6.1.4.1.8886.6.1.1.8.2.1.1
The unit index which is mapped to the port.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER

rcUspUspToPortMappingSlotIndex		1.3.6.1.4.1.8886.6.1.1.8.2.1.2
The slot index which is mapped to the port.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER

rcUspUspToPortMappingPortIndex		1.3.6.1.4.1.8886.6.1.1.8.2.1.3
The port index which is mapped to the port.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER

rcUspPortIndex		1.3.6.1.4.1.8886.6.1.1.8.2.1.4
The port index which the USP is mapped to.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

rcUspUnitNum		1.3.6.1.4.1.8886.6.1.1.8.3
The total unit number.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

rcUspUnitTable		1.3.6.1.4.1.8886.6.1.1.8.4
The table describes the detail of unit.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcUspUnitEntry

rcUspUnitEntry		1.3.6.1.4.1.8886.6.1.1.8.4.1
Defines an entry in the rcUspUnitTable.The index is rcUspUnitIndex.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcUspUnitEntry

rcUspUnitIndex		1.3.6.1.4.1.8886.6.1.1.8.4.1.1
The port index which the USP is mapped to.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER

rcUspUnitSlotNum		1.3.6.1.4.1.8886.6.1.1.8.4.1.2
The total slot num which the corresponding unit has.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

rcUspUnitPortNum		1.3.6.1.4.1.8886.6.1.1.8.4.1.3
The total port num which the corresponding unit has.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

rcUspSlotTable		1.3.6.1.4.1.8886.6.1.1.8.5
The table describes the detail of slot.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcUspSlotEntry

rcUspSlotEntry		1.3.6.1.4.1.8886.6.1.1.8.5.1
Defines an entry in the rcUspSlotTable.The indexes are rcUspSlotUnitIndex and rcUspSlotSlotIndex.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcUspSlotEntry

rcUspSlotUnitIndex		1.3.6.1.4.1.8886.6.1.1.8.5.1.1
The unit index which a slot belongs to.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER

rcUspSlotSlotIndex		1.3.6.1.4.1.8886.6.1.1.8.5.1.2
The slot index.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER

rcUspSlotSlotType		1.3.6.1.4.1.8886.6.1.1.8.5.1.3
The slot type.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	other(1), manage(2), manage-backup(3), power(4), fan(5), monite(6), fixed(7), gigabit-ethenet(8), tdm-clock(9), pon(10)

rcUspSlotRightSubcardType		1.3.6.1.4.1.8886.6.1.1.8.5.1.4
The type of subcard which is suitable to the slot.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

rcUspSlotActualSubcardType		1.3.6.1.4.1.8886.6.1.1.8.5.1.5
The type of subcard which is inserted to the slot.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

rcUspSlotSerial		1.3.6.1.4.1.8886.6.1.1.8.5.1.6
The serial number of slot.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

rcUspSlotHardVersion		1.3.6.1.4.1.8886.6.1.1.8.5.1.7
The hard version of slot.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

rcUspSlotSoftwareVersion		1.3.6.1.4.1.8886.6.1.1.8.5.1.8
The soft version of slot.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

rcUspSlotPortStart		1.3.6.1.4.1.8886.6.1.1.8.5.1.9
The global port index this slot starts from.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

rcUspSlotPortNum		1.3.6.1.4.1.8886.6.1.1.8.5.1.10
The number of ports this slot has.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

rcUspSlotSlotState		1.3.6.1.4.1.8886.6.1.1.8.5.1.11
The slot State.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	active(1), empty(2)

rcUspIfToUspMappingTable		1.3.6.1.4.1.8886.6.1.1.8.6
The table describes how the IF map to the USP.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcUspIfToUspMappingEntry

rcUspIfToUspMappingEntry		1.3.6.1.4.1.8886.6.1.1.8.6.1
Defines an entry in the rcUspIfToUspMappingTable.The index is ifIndex,while is unique in raisecom private mib.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcUspIfToUspMappingEntry

rcUspIfToUspMappingUnitIndex		1.3.6.1.4.1.8886.6.1.1.8.6.1.1
The unit index which IF is mapped to.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

rcUspIfToUspMappingSlotIndex		1.3.6.1.4.1.8886.6.1.1.8.6.1.2
The slot index which IF is mapped to.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

rcUspIfToUspMappingPortIndex		1.3.6.1.4.1.8886.6.1.1.8.6.1.3
The port index which IF is mapped to.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

rcUspIfType		1.3.6.1.4.1.8886.6.1.1.8.6.1.4
The IF type which IF is mapped to.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(0), port(1), line(2), client(3), tdm(4), ethernet(5), fastethernet(6), gigaethernet(7), tengigabitethernet(8), aggregator(9), ip(10), loopback(11), outband(12), max(13)

rcUspIfState		1.3.6.1.4.1.8886.6.1.1.8.6.1.5
The IF State.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	active(1), empty(2)

rcUspUspToIfMappingTable		1.3.6.1.4.1.8886.6.1.1.8.7
The table describes how the USP map to the IF.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RcUspUspToIfMappingEntry

rcUspUspToIfMappingEntry		1.3.6.1.4.1.8886.6.1.1.8.7.1
Defines an entry in the rcUspUspToIfMappingTable.The indexes are rcUspUspToIfMappingUnitIndex,rcUspUspToIfMappingSlotIndex,rcUspUspToIfMappingPortIndex and rcUspIfTypeIndex.
Status: current	Access: not-accessible
OBJECT-TYPE
	RcUspUspToIfMappingEntry

rcUspUspToIfMappingUnitIndex		1.3.6.1.4.1.8886.6.1.1.8.7.1.1
The unit index which is mapped to the IF.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER

rcUspUspToIfMappingSlotIndex		1.3.6.1.4.1.8886.6.1.1.8.7.1.2
The slot index which is mapped to the IF.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER

rcUspUspToIfMappingPortIndex		1.3.6.1.4.1.8886.6.1.1.8.7.1.3
The port index which is mapped to the IF.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER

rcUspIfTypeIndex		1.3.6.1.4.1.8886.6.1.1.8.7.1.4
The port type which is mapped to the IF.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	none(0), port(1), line(2), client(3), tdm(4), ethernet(5), fastethernet(6), gigaethernet(7), tengigabitethernet(8), aggregator(9), ip(10), loopback(11), outband(12), max(13)

rcUspIfIndex		1.3.6.1.4.1.8886.6.1.1.8.7.1.5
The If Index which is mapped to the IF.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER