RBN-L2VPN-MIB

Imported modules

SNMPv2-SMI	SNMPv2-CONF	SNMPv2-TC
RBN-TC	SNMP-FRAMEWORK-MIB	IF-MIB
RBN-SMI	INET-ADDRESS-MIB

Imported symbols

MODULE-IDENTITY	OBJECT-TYPE	Unsigned32
IpAddress	Integer32	NOTIFICATION-TYPE
MODULE-COMPLIANCE	OBJECT-GROUP	NOTIFICATION-GROUP
TEXTUAL-CONVENTION	TruthValue	RbnCircuitHandle
SnmpAdminString	InterfaceIndexOrZero	rbnMgmt
InetAddressType	InetAddress	InetPortNumber

Defined Types

RbnVpnVcType
Layer 2 VPN VC types.
TEXTUAL-CONVENTION
	INTEGER	unknown(0), frame(1), aal5(2), atmTransCell(3), vlan(4), ethernet(5), hdlc(6), ppp(7), cem(8), atmVccCell(9), atmVpcCell(10)

RbnVpnXcFlagsType
Layer 2 VPN Cross connect flag values.
TEXTUAL-CONVENTION
	BITS	none(0), inRib(1), deletingSignal(2), deletingConfig(3), inLblmap(4), updating(5), up(6), inLdp(7), fromLdp(8), fromConfig(9), stale(10), expSet(11), ismUp(12), peerUp(13), remoteEncap(14), localCbit(15), remoteCbit(16), primary(17), backup(18), primaryAutoRevert(19), standby(20), cwMismatch(21), sigParamsMatch(22)

RbnVpnPwFlagsType
Layer 2 VPN Pesudowire (PW) flag values.
TEXTUAL-CONVENTION
	BITS	none(0), inRib(1), deletingSignal(2), deletingConfig(3), inLblmap(4), updating(5), up(6), inLdp(7), fromLdp(8), fromConfig(9), stale(10), expSet(11), ismUp(12), peerUp(13), remoteEncap(14), localCbit(15), remoteCbit(16), primary(17), backup(18), primaryAutoRevert(19), standby(20), cwMismatch(21), sigParamsMatch(22), encapError(23)

RbnVpnPwStateType
Layer 2 VPN Cross connect (XC) state.
TEXTUAL-CONVENTION
	INTEGER	unknown(0), up(1), down(2), standby(3)

RbnVpnPsnType
Layer 2 VPN packet switched network(PSN) type.
TEXTUAL-CONVENTION
	INTEGER	unknown(0), ip(1), ipsec(2), mpls(3)

RbnMplsL2VpnStaticEntry
SEQUENCE
	rbnMplsL2VpnStaticInLabel	Unsigned32
	rbnMplsL2VpnStaticPeerAddr	IpAddress
	rbnMplsL2VpnStaticCctHandle	RbnCircuitHandle
	rbnMplsL2VpnStaticVpnCctHandle	RbnCircuitHandle
	rbnMplsL2VpnStaticExpBits	Unsigned32
	rbnMplsL2VpnStaticInputCctUp	TruthValue
	rbnMplsL2VpnStaticXcFlags	RbnVpnXcFlagsType
	rbnMplsL2VpnStaticIfIndexOrZero	InterfaceIndexOrZero
	rbnMplsL2VpnStaticPwFlags	RbnVpnPwFlagsType
	rbnMplsL2VpnStaticPwState	RbnVpnPwStateType
	rbnMplsL2VpnStaticVpnLabel	Unsigned32

RbnMplsL2VpnLdpEntry
SEQUENCE
	rbnMplsL2VpnLdpVcId	Unsigned32
	rbnMplsL2VpnLdpPeerAddr	IpAddress
	rbnMplsL2VpnLdpCctHandle	RbnCircuitHandle
	rbnMplsL2VpnLdpVpnCctHandle	RbnCircuitHandle
	rbnMplsL2VpnLdpInLabel	Unsigned32
	rbnMplsL2VpnLdpVpnLabel	Unsigned32
	rbnMplsL2VpnLdpRemGrpId	Unsigned32
	rbnMplsL2VpnLdpLocEncap	SnmpAdminString
	rbnMplsL2VpnLdpRemEncap	SnmpAdminString
	rbnMplsL2VpnLdpLocVcType	RbnVpnVcType
	rbnMplsL2VpnLdpRemVcType	RbnVpnVcType
	rbnMplsL2VpnLdpLocMtu	Unsigned32
	rbnMplsL2VpnLdpRemMtu	Unsigned32
	rbnMplsL2VpnLdpXcCctUp	TruthValue
	rbnMplsL2VpnLdpExpBits	Unsigned32
	rbnMplsL2VpnLdpInputCctUp	TruthValue
	rbnMplsL2VpnLdpXcFlags	RbnVpnXcFlagsType
	rbnMplsL2VpnLdpIfIndexOrZero	InterfaceIndexOrZero
	rbnMplsL2VpnLdpPwFlags	RbnVpnPwFlagsType
	rbnMplsL2VpnLdpPwState	RbnVpnPwStateType

RbnUdpL2VpnStaticEntry
SEQUENCE
	rbnUdpL2VpnStaticPeerPort	InetPortNumber
	rbnUdpL2VpnStaticPeerAddressType	InetAddressType
	rbnUdpL2VpnStaticPeerAddress	InetAddress
	rbnUdpL2VpnStaticSourceAddressType	InetAddressType
	rbnUdpL2VpnStaticSourceAddress	InetAddress
	rbnUdpL2VpnStaticSourcePort	InetPortNumber
	rbnUdpL2vpnStaticAccessCctHandle	RbnCircuitHandle
	rbnUdpL2VpnStaticVpnCctHandle	RbnCircuitHandle
	rbnUdpL2VpnStaticInputCctUp	TruthValue
	rbnUdpL2VpnStaticIfIndexOrZero	InterfaceIndexOrZero
	rbnUdpL2VpnStaticPwFlags	RbnVpnPwFlagsType
	rbnUdpL2VpnStaticPwState	RbnVpnPwStateType
	rbnUdpL2vpnStaticDscpCode	INTEGER
	rbnUdpL2VpnStaticPsnType	RbnVpnPsnType

RbnL2VpnStaticEntry
SEQUENCE
	rbnL2VpnStaticPeerAddr	IpAddress
	rbnL2VpnStaticVpnLabel	Unsigned32
	rbnL2VpnStaticCctHandle	RbnCircuitHandle
	rbnL2VpnStaticVpnCctHandle	RbnCircuitHandle
	rbnL2VpnStaticExpBits	Unsigned32
	rbnL2VpnStaticInputCctUp	TruthValue
	rbnL2VpnStaticXcFlags	RbnVpnXcFlagsType
	rbnL2VpnStaticIfIndexOrZero	InterfaceIndexOrZero

RbnL2VpnLdpEntry
SEQUENCE
	rbnL2VpnLdpPeerAddr	IpAddress
	rbnL2VpnLdpVcId	Integer32
	rbnL2VpnLdpCctHandle	RbnCircuitHandle
	rbnL2VpnLdpVpnCctHandle	RbnCircuitHandle
	rbnL2VpnLdpInLabel	Unsigned32
	rbnL2VpnLdpVpnLabel	Unsigned32
	rbnL2VpnLdpRemGrpId	Unsigned32
	rbnL2VpnLdpLocEncap	SnmpAdminString
	rbnL2VpnLdpRemEncap	SnmpAdminString
	rbnL2VpnLdpLocVcType	RbnVpnVcType
	rbnL2VpnLdpRemVcType	RbnVpnVcType
	rbnL2VpnLdpLocMtu	Unsigned32
	rbnL2VpnLdpRemMtu	Unsigned32
	rbnL2VpnLdpXcCctUp	TruthValue
	rbnL2VpnLdpExpBits	Unsigned32
	rbnL2VpnLdpInputCctUp	TruthValue
	rbnL2VpnLdpXcFlags	RbnVpnXcFlagsType
	rbnL2VpnLdpIfIndexOrZero	InterfaceIndexOrZero

Defined Values

rbnL2VpnMIB		1.3.6.1.4.1.2352.2.39
This management information base displays Layer 2 Virtual Private Networks(VPN) / Pesudowires(PWs) information.
MODULE-IDENTITY

rbnMplsL2VpnMIBNotifications		1.3.6.1.4.1.2352.2.39.0
OBJECT IDENTIFIER

rbnL2VpnMIBObjects		1.3.6.1.4.1.2352.2.39.1
OBJECT IDENTIFIER

rbnL2VpnMIBConformance		1.3.6.1.4.1.2352.2.39.2
OBJECT IDENTIFIER

rbnMplsL2VpnMIBObjects		1.3.6.1.4.1.2352.2.39.3
OBJECT IDENTIFIER

rbnMplsL2VpnMIBConformance		1.3.6.1.4.1.2352.2.39.4
OBJECT IDENTIFIER

rbnMplsL2VpnMIBScalars		1.3.6.1.4.1.2352.2.39.5
OBJECT IDENTIFIER

rbnUdpL2VpnMIBObjects		1.3.6.1.4.1.2352.2.39.6
OBJECT IDENTIFIER

rbnMplsL2VpnNotificationEnable		1.3.6.1.4.1.2352.2.39.5.1
If this object is true, then it enables the generation of all notifications defined in this MIB. This object's value should be preserved across agent reboots.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

rbnMplsL2VpnStaticTable		1.3.6.1.4.1.2352.2.39.3.3
This table contains objects which identify static Layer 2 VPN circuits. With respect to creation and deletion of entries in this table, rows are created or deleted when the VPN circuit is configured.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RbnMplsL2VpnStaticEntry

rbnMplsL2VpnStaticEntry		1.3.6.1.4.1.2352.2.39.3.3.1
A conceptual row in the rbnMplsL2VpnStaticTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	RbnMplsL2VpnStaticEntry

rbnMplsL2VpnStaticInLabel		1.3.6.1.4.1.2352.2.39.3.3.1.1
This object indicates the unique value assigned to a particular static VPN circuit.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

rbnMplsL2VpnStaticPeerAddr		1.3.6.1.4.1.2352.2.39.3.3.1.2
This object indicates the ip address of the VPN peer.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

rbnMplsL2VpnStaticCctHandle		1.3.6.1.4.1.2352.2.39.3.3.1.3
This object indicates the internal representation of the physical circuit to which this VPN is connected. A hexadecimal value of ff ff ff ff ff ff ff ff indicates an invalid circuit.
Status: current	Access: read-only
OBJECT-TYPE
	RbnCircuitHandle

rbnMplsL2VpnStaticVpnCctHandle		1.3.6.1.4.1.2352.2.39.3.3.1.4
This object indicates the internal representation of VPN pseudo circuit.
Status: current	Access: read-only
OBJECT-TYPE
	RbnCircuitHandle

rbnMplsL2VpnStaticExpBits		1.3.6.1.4.1.2352.2.39.3.3.1.5
This object indicates the number of exp bits configured for this VPN circuit.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rbnMplsL2VpnStaticInputCctUp		1.3.6.1.4.1.2352.2.39.3.3.1.6
This object indicates the status of the VPN attachment circuit. A value of true indicates that the VPN attachment circuit is connected with its remote site. A value of false indicates that the remote site is not presently connected.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rbnMplsL2VpnStaticXcFlags		1.3.6.1.4.1.2352.2.39.3.3.1.7
This object indicates more detailed information on the status of the VPN circuit. This object is a bit field so it may contain one or more of these values.
Status: current	Access: read-only
OBJECT-TYPE
	RbnVpnXcFlagsType

rbnMplsL2VpnStaticIfIndexOrZero		1.3.6.1.4.1.2352.2.39.3.3.1.8
This object indicates whether there is a corresponding entry in the ifTable. A non-zero value indicates the ifIndex of the entry in the ifTable. A value of zero indicates that there is no entry.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndexOrZero

rbnMplsL2VpnStaticPwFlags		1.3.6.1.4.1.2352.2.39.3.3.1.9
This object indicates more detailed information on the status of the VPN circuit. This object is a bit field so it may contain one or more of these values.
Status: current	Access: read-only
OBJECT-TYPE
	RbnVpnPwFlagsType

rbnMplsL2VpnStaticPwState		1.3.6.1.4.1.2352.2.39.3.3.1.10
This object indicates the status of the VPN input circuit. A value of up(1) indicates that the VPN circuit is active i.e. connected with its remote site. A value of down(2) indicates that the remote site is not presently connected. A value of standby(3) indicates the the PW is in pending state to become active(i.e. up)
Status: current	Access: read-only
OBJECT-TYPE
	RbnVpnPwStateType

rbnMplsL2VpnStaticVpnLabel		1.3.6.1.4.1.2352.2.39.3.3.1.11
This object indicates the value used by the remote connection in order to identify this VPN circuit when communicating with the label manager.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	4096..65535

rbnMplsL2VpnLdpTable		1.3.6.1.4.1.2352.2.39.3.4
This table contains objects which identify Layer Distribution Protocol Layer 2 VPN circuits. With respect to creation and deletion of entries in this table, rows are created or deleted when the VPN circuit is configured.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RbnMplsL2VpnLdpEntry

rbnMplsL2VpnLdpEntry		1.3.6.1.4.1.2352.2.39.3.4.1
A conceptual row in the rbnMplsL2VpnLdpTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	RbnMplsL2VpnLdpEntry

rbnMplsL2VpnLdpVcId		1.3.6.1.4.1.2352.2.39.3.4.1.1
This object indicates the unique virtual VPN circuit id assigned to this circuit.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	0..4294967295

rbnMplsL2VpnLdpPeerAddr		1.3.6.1.4.1.2352.2.39.3.4.1.2
This object indicates the ip address if the VPN peer.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

rbnMplsL2VpnLdpCctHandle		1.3.6.1.4.1.2352.2.39.3.4.1.3
This object indicates the internal representation of the physical circuit to which this VPN is connected. A hexadecimal value of ff ff ff ff ff ff ff ff indicates an invalid circuit.
Status: current	Access: read-only
OBJECT-TYPE
	RbnCircuitHandle

rbnMplsL2VpnLdpVpnCctHandle		1.3.6.1.4.1.2352.2.39.3.4.1.4
This object indicates the internal representation of the VPN pseudo circuit.
Status: current	Access: read-only
OBJECT-TYPE
	RbnCircuitHandle

rbnMplsL2VpnLdpInLabel		1.3.6.1.4.1.2352.2.39.3.4.1.5
This object indicates the value setup in the local configuration to identify this VPN circuit.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rbnMplsL2VpnLdpVpnLabel		1.3.6.1.4.1.2352.2.39.3.4.1.6
This object indicates the value used by the remote connection in order to identify this VPN circuit when communicating with the local manager.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rbnMplsL2VpnLdpRemGrpId		1.3.6.1.4.1.2352.2.39.3.4.1.7
This object indicates the remote group of which this VPN circuit is a part.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rbnMplsL2VpnLdpLocEncap		1.3.6.1.4.1.2352.2.39.3.4.1.8
This object indicates the local encaps type associated with this VPN circuit.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString	Size(0..80)

rbnMplsL2VpnLdpRemEncap		1.3.6.1.4.1.2352.2.39.3.4.1.9
This object indicates the remote encaps type associated with this VPN circuit.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString	Size(0..80)

rbnMplsL2VpnLdpLocVcType		1.3.6.1.4.1.2352.2.39.3.4.1.10
This object indicates the type of virtual circuit on the local system.
Status: current	Access: read-only
OBJECT-TYPE
	RbnVpnVcType

rbnMplsL2VpnLdpRemVcType		1.3.6.1.4.1.2352.2.39.3.4.1.11
This object indicates the type of virtual circuit on the remote system.
Status: current	Access: read-only
OBJECT-TYPE
	RbnVpnVcType

rbnMplsL2VpnLdpLocMtu		1.3.6.1.4.1.2352.2.39.3.4.1.12
This object indicates the maximum transmission unit of the local VPN circuit.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rbnMplsL2VpnLdpRemMtu		1.3.6.1.4.1.2352.2.39.3.4.1.13
This object indicates the maximum transmission unit of the remote connection.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rbnMplsL2VpnLdpXcCctUp		1.3.6.1.4.1.2352.2.39.3.4.1.14
This object indicates the status of the VPN cross connect circuit state. A value of true indicates that the VPN circuit is connected with its remote site and attachment circuit is up (rbnMplsL2VpnLdpInputCctUp is true). A value of false indicates that the remote site is not presently connected, this mean that either the PSN is not reachable or the attachment circuit is down or signaling parameters mismatched.
Status: deprecated	Access: read-only
OBJECT-TYPE
	TruthValue

rbnMplsL2VpnLdpExpBits		1.3.6.1.4.1.2352.2.39.3.4.1.15
This object indicates the number of exp bits configured for this VPN circuit.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

rbnMplsL2VpnLdpInputCctUp		1.3.6.1.4.1.2352.2.39.3.4.1.16
This object indicates the status of the VPN attachment circuit. A value of true indicates that the VPN attachment circuit is up. A value of false indicates the attachment circuit state is down.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rbnMplsL2VpnLdpXcFlags		1.3.6.1.4.1.2352.2.39.3.4.1.17
This object indicates more detailed information on the status of the VPN circuit. This object is a bit field so it may contain one or more of these values.
Status: deprecated	Access: read-only
OBJECT-TYPE
	RbnVpnXcFlagsType

rbnMplsL2VpnLdpIfIndexOrZero		1.3.6.1.4.1.2352.2.39.3.4.1.18
This object indicates whether there is a corresponding entry in the ifTable. A non-zero value indicates the ifIndex of the entry in the ifTable. A value of zero indicates that there is no entry.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndexOrZero

rbnMplsL2VpnLdpPwFlags		1.3.6.1.4.1.2352.2.39.3.4.1.19
This object indicates more detailed information on the status of the VPN circuit. This object is a bit field so it may contain one or more of these values.
Status: current	Access: read-only
OBJECT-TYPE
	RbnVpnPwFlagsType

rbnMplsL2VpnLdpPwState		1.3.6.1.4.1.2352.2.39.3.4.1.20
This object indicates the status of the VPN input circuit. A value of up(1) indicates that the VPN circuit is active i.e. connected with its remote site. A value of down(2) indicates that the remote site is not presently connected. A value of standby(3) indicates the the PW is in pending state to become active(i.e. up)
Status: current	Access: read-only
OBJECT-TYPE
	RbnVpnPwStateType

rbnUdpL2VpnStaticTable		1.3.6.1.4.1.2352.2.39.6.1
This table contains objects which identify static UDP Layer 2 VPN circuits. With respect to creation and deletion of entries in this table, rows are created or deleted when the VPN circuit is configured.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RbnUdpL2VpnStaticEntry

rbnUdpL2VpnStaticEntry		1.3.6.1.4.1.2352.2.39.6.1.1
A conceptual row in the rbnUdpL2VpnStaticTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	RbnUdpL2VpnStaticEntry

rbnUdpL2VpnStaticPeerPort		1.3.6.1.4.1.2352.2.39.6.1.1.1
This object indicates the peer port number for this UDP L2 VPN circuit.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetPortNumber

rbnUdpL2VpnStaticPeerAddressType		1.3.6.1.4.1.2352.2.39.6.1.1.2
This object indicates the peer IP address type for this UDP L2 VPN circuit.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddressType

rbnUdpL2VpnStaticPeerAddress		1.3.6.1.4.1.2352.2.39.6.1.1.3
This object indicates the peer IP address for this UDP L2 VPN circuit. The peer address type is determined by the value of the corresponding rbnUdpL2VpnStaticPeerAddressType.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddress

rbnUdpL2VpnStaticSourceAddressType		1.3.6.1.4.1.2352.2.39.6.1.1.4
This object indicates the source IP address type for this UDP L2 VPN circuit.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddressType

rbnUdpL2VpnStaticSourceAddress		1.3.6.1.4.1.2352.2.39.6.1.1.5
This object indicates the source IP address for this UDP L2 VPN circuit. The source address type is determined by the value of the corresponding rbnUdpL2VpnStaticSourceAddressType.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddress

rbnUdpL2VpnStaticSourcePort		1.3.6.1.4.1.2352.2.39.6.1.1.6
This object indicates the source port number for this UDP L2 VPN circuit.
Status: current	Access: read-only
OBJECT-TYPE
	InetPortNumber

rbnUdpL2vpnStaticAccessCctHandle		1.3.6.1.4.1.2352.2.39.6.1.1.7
This object indicates the internal representation of the access circuit for this UDP L2 VPN circuit.
Status: current	Access: read-only
OBJECT-TYPE
	RbnCircuitHandle

rbnUdpL2VpnStaticVpnCctHandle		1.3.6.1.4.1.2352.2.39.6.1.1.8
This object indicates the internal representation of this UDP L2 VPN circuit.
Status: current	Access: read-only
OBJECT-TYPE
	RbnCircuitHandle

rbnUdpL2VpnStaticInputCctUp		1.3.6.1.4.1.2352.2.39.6.1.1.9
This object indicates the status of this UDP L2 VPN circuit. A value of true indicates that the VPN circuit is connected with it's remote site. A value of false indicates that the remote site is not presently connected.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

rbnUdpL2VpnStaticIfIndexOrZero		1.3.6.1.4.1.2352.2.39.6.1.1.10
This object indicates whether there is a corresponding entry of this UDP L2 VPN access circuit in the ifTable. A non-zero value indicates the ifIndex of the entry in the ifTable. A value of zero indicates that there is no entry (for example, a pre-provisioned access circuit is used).
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndexOrZero

rbnUdpL2VpnStaticPwFlags		1.3.6.1.4.1.2352.2.39.6.1.1.11
This object indicates more detailed information on the status of this UDP L2 VPN circuit. This object is a bit field so it may contain one or more of these values.
Status: current	Access: read-only
OBJECT-TYPE
	RbnVpnPwFlagsType

rbnUdpL2vpnStaticDscpCode		1.3.6.1.4.1.2352.2.39.6.1.1.12
Diffserver code for the CES over UDP PW. Default is Zero. The dscp code values are listed as follows: 0..63 Differentiated services codepoint value af11 Assured Forwarding - Class 1/Drop precedence 1 af12 Assured Forwarding - Class 1/Drop precedence 2 af13 Assured Forwarding - Class 1/Drop precedence 3 af21 Assured Forwarding - Class 2/Drop precedence 1 af22 Assured Forwarding - Class 2/Drop precedence 2 af23 Assured Forwarding - Class 2/Drop precedence 3 af31 Assured Forwarding - Class 3/Drop precedence 1 af32 Assured Forwarding - Class 3/Drop precedence 2 af33 Assured Forwarding - Class 3/Drop precedence 3 af41 Assured Forwarding - Class 4/Drop precedence 1 af42 Assured Forwarding - Class 4/Drop precedence 2 af43 Assured Forwarding - Class 4/Drop precedence 3
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

rbnUdpL2VpnStaticPwState		1.3.6.1.4.1.2352.2.39.6.1.1.13
This object indicates the status of this UDP L2 VPN circuit. A value of up(1) indicates that the VPN circuit is active i.e. connected with its remote site. A value of down(2) indicates that the remote site is not presently connected. A value of standby(3) indicates the the PW is in pending state to become active (i.e. up)
Status: current	Access: read-only
OBJECT-TYPE
	RbnVpnPwStateType

rbnUdpL2VpnStaticPsnType		1.3.6.1.4.1.2352.2.39.6.1.1.14
This object indicates the packet switched networks(PSN) type for this UDP L2 VPN circuit.
Status: current	Access: read-only
OBJECT-TYPE
	RbnVpnPsnType

rbnMplsL2VpnLdpPwStateChange		1.3.6.1.4.1.2352.2.39.0.1
This notification is generated when PW state transitions operationally to UP/DOWN/STANDBY.
Status: current	Access: read-only
NOTIFICATION-TYPE

rbnL2VpnMIBGroups		1.3.6.1.4.1.2352.2.39.2.1
OBJECT IDENTIFIER

rbnL2VpnMIBCompliances		1.3.6.1.4.1.2352.2.39.2.2
OBJECT IDENTIFIER

rbnMplsL2VpnMIBGroups		1.3.6.1.4.1.2352.2.39.2.3
OBJECT IDENTIFIER

rbnMplsL2VpnMIBCompliances		1.3.6.1.4.1.2352.2.39.2.4
OBJECT IDENTIFIER

rbnMplsL2VpnPwMIBCompliance		1.3.6.1.4.1.2352.2.39.2.2.2
The compliance statement for the L2VPN MIB.
Status: current	Access: read-only
MODULE-COMPLIANCE

rbnMplsL2VpnPwScalarGroup		1.3.6.1.4.1.2352.2.39.2.1.3
Collection of scalar objects required for L2VPN PW management
Status: current	Access: read-only
OBJECT-GROUP

rbnMplsL2VpnStaticPwGroup		1.3.6.1.4.1.2352.2.39.2.1.4
A collection of objects providing information about the status of static L2 VPN Pesudowires.
Status: current	Access: read-only
OBJECT-GROUP

rbnMplsL2VpnLdpPwGroup		1.3.6.1.4.1.2352.2.39.2.1.5
A collection of objects providing information about the status of L2 VPN Pesudowires using Label Detection Protocol.
Status: current	Access: read-only
OBJECT-GROUP

rbnMplsL2VpnPwNotificationGroup		1.3.6.1.4.1.2352.2.39.2.1.6
Objects required for L2VPN PW notifications.
Status: current	Access: read-only
NOTIFICATION-GROUP

rbnUdpL2VpnPwMIBCompliance		1.3.6.1.4.1.2352.2.39.2.2.3
The compliance statement for the L2VPN MIB.
Status: current	Access: read-only
MODULE-COMPLIANCE

rbnUdpL2VpnStaticPwGroup		1.3.6.1.4.1.2352.2.39.2.1.7
A collection of objects providing information about the status of static L2 VPN Pesudowires.
Status: current	Access: read-only
OBJECT-GROUP

rbnL2VpnStaticTable		1.3.6.1.4.1.2352.2.39.1.1
This table contains objects which identify static Layer 2 VPN circuits. With respect to creation and deletion of entries in this table, rows are created or deleted when the VPN circuit is configured.
Status: obsolete	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RbnL2VpnStaticEntry

rbnL2VpnStaticEntry		1.3.6.1.4.1.2352.2.39.1.1.1
A conceptual row in the rbnL2VpnStaticTable.
Status: obsolete	Access: not-accessible
OBJECT-TYPE
	RbnL2VpnStaticEntry

rbnL2VpnStaticPeerAddr		1.3.6.1.4.1.2352.2.39.1.1.1.1
This object indicates the ip address of the VPN peer.
Status: obsolete	Access: not-accessible
OBJECT-TYPE
	IpAddress

rbnL2VpnStaticVpnLabel		1.3.6.1.4.1.2352.2.39.1.1.1.2
This object indicates the unique value assigned to a particular static VPN circuit.
Status: obsolete	Access: not-accessible
OBJECT-TYPE
	Unsigned32	4096..65535

rbnL2VpnStaticCctHandle		1.3.6.1.4.1.2352.2.39.1.1.1.3
This object indicates the internal representation of the physical circuit to which this VPN is connected. A hexadecimal value of ff ff ff ff ff ff ff ff indicates an invalid circuit.
Status: obsolete	Access: read-only
OBJECT-TYPE
	RbnCircuitHandle

rbnL2VpnStaticVpnCctHandle		1.3.6.1.4.1.2352.2.39.1.1.1.4
This object indicates the internal representation of VPN pseudo circuit.
Status: obsolete	Access: read-only
OBJECT-TYPE
	RbnCircuitHandle

rbnL2VpnStaticExpBits		1.3.6.1.4.1.2352.2.39.1.1.1.5
This object indicates the number of exp bits configured for this VPN circuit.
Status: obsolete	Access: read-only
OBJECT-TYPE
	Unsigned32

rbnL2VpnStaticInputCctUp		1.3.6.1.4.1.2352.2.39.1.1.1.6
This object indicates the status of the VPN input circuit. A value of true indicates that the VPN circuit is connected with it's remote site. A value of false indicates that the remote site is not presently connected.
Status: obsolete	Access: read-only
OBJECT-TYPE
	TruthValue

rbnL2VpnStaticXcFlags		1.3.6.1.4.1.2352.2.39.1.1.1.7
This object indicates more detailed information on the status of the VPN circuit. This object is a bit field so it may contain one or more of these values.
Status: obsolete	Access: read-only
OBJECT-TYPE
	RbnVpnXcFlagsType

rbnL2VpnStaticIfIndexOrZero		1.3.6.1.4.1.2352.2.39.1.1.1.8
This object indicates whether there is a corresponding entry in the ifTable. A non-zero value indicates the ifIndex of the entry in the ifTable. A value of zero indicates that there is no entry.
Status: obsolete	Access: read-only
OBJECT-TYPE
	InterfaceIndexOrZero

rbnL2VpnLdpTable		1.3.6.1.4.1.2352.2.39.1.2
This table contains objects which identify Layer Distribution Protocol Layer 2 VPN circuits. With respect to creation and deletion of entries in this table, rows are created or deleted when the VPN circuit is configured.
Status: obsolete	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RbnL2VpnLdpEntry

rbnL2VpnLdpEntry		1.3.6.1.4.1.2352.2.39.1.2.1
A conceptual row in the rbnL2VpnStaticTable.
Status: obsolete	Access: not-accessible
OBJECT-TYPE
	RbnL2VpnLdpEntry

rbnL2VpnLdpPeerAddr		1.3.6.1.4.1.2352.2.39.1.2.1.1
This object indicates the ip address if the VPN peer.
Status: obsolete	Access: not-accessible
OBJECT-TYPE
	IpAddress

rbnL2VpnLdpVcId		1.3.6.1.4.1.2352.2.39.1.2.1.2
This object indicates the unique virtual VPN circuit id assigned to this circuit.
Status: obsolete	Access: not-accessible
OBJECT-TYPE
	Integer32	0..2147483647

rbnL2VpnLdpCctHandle		1.3.6.1.4.1.2352.2.39.1.2.1.3
This object indicates the internal representation of the physical circuit to which this VPN is connected. A hexadecimal value of ff ff ff ff ff ff ff ff indicates an invalid circuit.
Status: obsolete	Access: read-only
OBJECT-TYPE
	RbnCircuitHandle

rbnL2VpnLdpVpnCctHandle		1.3.6.1.4.1.2352.2.39.1.2.1.4
This object indicates the internal representation of the VPN pseudo circuit.
Status: obsolete	Access: read-only
OBJECT-TYPE
	RbnCircuitHandle

rbnL2VpnLdpInLabel		1.3.6.1.4.1.2352.2.39.1.2.1.5
This object indicates the value setup in the local configuration to identify this VPN circuit.
Status: obsolete	Access: read-only
OBJECT-TYPE
	Unsigned32

rbnL2VpnLdpVpnLabel		1.3.6.1.4.1.2352.2.39.1.2.1.6
This object indicates the value used by the remote connection in order to identify this VPN circuit when communicating with the local manager.
Status: obsolete	Access: read-only
OBJECT-TYPE
	Unsigned32

rbnL2VpnLdpRemGrpId		1.3.6.1.4.1.2352.2.39.1.2.1.7
This object indicates the remote group of which this VPN circuit is a part.
Status: obsolete	Access: read-only
OBJECT-TYPE
	Unsigned32

rbnL2VpnLdpLocEncap		1.3.6.1.4.1.2352.2.39.1.2.1.8
This object indicates the local encaps type associated with this VPN circuit.
Status: obsolete	Access: read-only
OBJECT-TYPE
	SnmpAdminString	Size(0..80)

rbnL2VpnLdpRemEncap		1.3.6.1.4.1.2352.2.39.1.2.1.9
This object indicates the remote encaps type associated with this VPN circuit.
Status: obsolete	Access: read-only
OBJECT-TYPE
	SnmpAdminString	Size(0..80)

rbnL2VpnLdpLocVcType		1.3.6.1.4.1.2352.2.39.1.2.1.10
This object indicates the type of virtual circuit on the local system.
Status: obsolete	Access: read-only
OBJECT-TYPE
	RbnVpnVcType

rbnL2VpnLdpRemVcType		1.3.6.1.4.1.2352.2.39.1.2.1.11
This object indicates the type of virtual circuit on the remote system.
Status: obsolete	Access: read-only
OBJECT-TYPE
	RbnVpnVcType

rbnL2VpnLdpLocMtu		1.3.6.1.4.1.2352.2.39.1.2.1.12
This object indicates the maximum transmission unit of the local VPN circuit.
Status: obsolete	Access: read-only
OBJECT-TYPE
	Unsigned32

rbnL2VpnLdpRemMtu		1.3.6.1.4.1.2352.2.39.1.2.1.13
This object indicates the maximum transmission unit of the remote connection.
Status: obsolete	Access: read-only
OBJECT-TYPE
	Unsigned32

rbnL2VpnLdpXcCctUp		1.3.6.1.4.1.2352.2.39.1.2.1.14
This object indicates the status of the VPN cross connect circuit. A value of true indicates that the VPN circuit is connected with it's remote site. A value of false indicates that the remote site is not presently connected.
Status: obsolete	Access: read-only
OBJECT-TYPE
	TruthValue

rbnL2VpnLdpExpBits		1.3.6.1.4.1.2352.2.39.1.2.1.15
This object indicates the number of exp bits configured for this VPN circuit.
Status: obsolete	Access: read-only
OBJECT-TYPE
	Unsigned32

rbnL2VpnLdpInputCctUp		1.3.6.1.4.1.2352.2.39.1.2.1.16
This object indicates the status of the VPN input circuit. A value of true indicates that the VPN circuit is connected with it's remote site. A value of false indicates that the remote site is not presently connected.
Status: obsolete	Access: read-only
OBJECT-TYPE
	TruthValue

rbnL2VpnLdpXcFlags		1.3.6.1.4.1.2352.2.39.1.2.1.17
This object indicates more detailed information on the status of the VPN circuit. This object is a bit field so it may contain one or more of these values.
Status: obsolete	Access: read-only
OBJECT-TYPE
	RbnVpnXcFlagsType

rbnL2VpnLdpIfIndexOrZero		1.3.6.1.4.1.2352.2.39.1.2.1.18
This object indicates whether there is a corresponding entry in the ifTable. A non-zero value indicates the ifIndex of the entry in the ifTable. A value of zero indicates that there is no entry.
Status: obsolete	Access: read-only
OBJECT-TYPE
	InterfaceIndexOrZero

rbnL2VpnMIBCompliance		1.3.6.1.4.1.2352.2.39.2.2.1
The compliance statement for the L2VPN MIB.
Status: obsolete	Access: read-only
MODULE-COMPLIANCE

rbnMplsL2VpnMIBCompliance		1.3.6.1.4.1.2352.2.39.2.4.1
The compliance statement for the L2VPN MIB.
Status: current	Access: read-only
MODULE-COMPLIANCE

rbnL2VpnStaticGroup		1.3.6.1.4.1.2352.2.39.2.1.1
A collection of objects providing information about the status of static L2 VPN connections.
Status: obsolete	Access: read-only
OBJECT-GROUP

rbnMplsL2VpnStaticGroup		1.3.6.1.4.1.2352.2.39.2.3.1
A collection of objects providing information about the status of static L2 VPN connections.
Status: current	Access: read-only
OBJECT-GROUP

rbnL2VpnLdpGroup		1.3.6.1.4.1.2352.2.39.2.1.2
A collection of objects providing information about the status of L2 VPN connections using Label Detection Protocol.
Status: obsolete	Access: read-only
OBJECT-GROUP

rbnMplsL2VpnLdpGroup		1.3.6.1.4.1.2352.2.39.2.3.2
A collection of objects providing information about the status of L2 VPN connections using Label Detection Protocol.
Status: current	Access: read-only
OBJECT-GROUP