PowerConnect3248-MIB
File:
PowerConnect3248-MIB.mib (110346 bytes)
Imported modules
Imported symbols
Defined Types
| ValidStatus |
|
| A simple status value for the object to create and destroy
a table entry. This is a simplified variant of RowStatus as it
supports only two values. Setting it to valid(1) creates an entry.
Setting it to invalid(2) destroys an entry. |
| TEXTUAL-CONVENTION |
|
|
|
| |
INTEGER |
valid(1), invalid(2) |
|
| SwitchInfoEntry |
|
| SEQUENCE |
|
|
|
| |
swUnitIndex |
Integer32 |
|
| |
swHardwareVer |
DisplayString |
|
| |
swMicrocodeVer |
DisplayString |
|
| |
swLoaderVer |
DisplayString |
|
| |
swBootRomVer |
DisplayString |
|
| |
swOpCodeVer |
DisplayString |
|
| |
swPortNumber |
Integer32 |
|
| |
swPowerStatus |
INTEGER |
|
| |
swRoleInSystem |
INTEGER |
|
| |
swSerialNumber |
DisplayString |
|
| |
swExpansionSlot1 |
INTEGER |
|
| |
swExpansionSlot2 |
INTEGER |
|
| |
swServiceTag |
DisplayString |
|
| SwitchIndivPowerEntry |
|
| SEQUENCE |
|
|
|
| |
swIndivPowerUnitIndex |
Integer32 |
|
| |
swIndivPowerIndex |
INTEGER |
|
| |
swIndivPowerStatus |
INTEGER |
|
| PortEntry |
|
| SEQUENCE |
|
|
|
| |
portIndex |
Integer32 |
|
| |
portName |
DisplayString |
|
| |
portType |
INTEGER |
|
| |
portSpeedDpxCfg |
INTEGER |
|
| |
portFlowCtrlCfg |
INTEGER |
|
| |
portCapabilities |
BITS |
|
| |
portAutonegotiation |
INTEGER |
|
| |
portSpeedDpxStatus |
INTEGER |
|
| |
portFlowCtrlStatus |
INTEGER |
|
| |
portTrunkIndex |
Integer32 |
|
| TrunkEntry |
|
| SEQUENCE |
|
|
|
| |
trunkIndex |
Integer32 |
|
| |
trunkPorts |
PortList |
|
| |
trunkCreation |
INTEGER |
|
| |
trunkStatus |
INTEGER |
|
| LacpPortEntry |
|
| SEQUENCE |
|
|
|
| |
lacpPortIndex |
Integer32 |
|
| |
lacpPortStatus |
INTEGER |
|
| StaPortEntry |
|
| SEQUENCE |
|
|
|
| |
staPortIndex |
Integer32 |
|
| |
staPortFastForward |
EnabledStatus |
|
| |
staPortProtocolMigration |
TruthValue |
|
| |
staPortAdminEdgePort |
TruthValue |
|
| |
staPortOperEdgePort |
TruthValue |
|
| |
staPortAdminPointToPoint |
INTEGER |
|
| |
staPortOperPointToPoint |
TruthValue |
|
| |
staPortLongPathCost |
Integer32 |
|
| XstInstanceCfgEntry |
|
| SEQUENCE |
|
|
|
| |
xstInstanceCfgIndex |
Integer32 |
|
| |
xstInstanceCfgPriority |
Integer32 |
|
| |
xstInstanceCfgTimeSinceTopologyChange |
Integer32 |
|
| |
xstInstanceCfgTopChanges |
Integer32 |
|
| |
xstInstanceCfgDesignatedRoot |
BridgeId |
|
| |
xstInstanceCfgRootCost |
Integer32 |
|
| |
xstInstanceCfgRootPort |
Integer32 |
|
| |
xstInstanceCfgMaxAge |
Timeout |
|
| |
xstInstanceCfgHelloTime |
Timeout |
|
| |
xstInstanceCfgHoldTime |
Timeout |
|
| |
xstInstanceCfgForwardDelay |
Timeout |
|
| |
xstInstanceCfgBridgeMaxAge |
Timeout |
|
| |
xstInstanceCfgBridgeHelloTime |
Timeout |
|
| |
xstInstanceCfgBridgeForwardDelay |
Timeout |
|
| |
xstInstanceCfgTxHoldCount |
Integer32 |
|
| |
xstInstanceCfgPathCostMethod |
INTEGER |
|
| XstInstancePortEntry |
|
| SEQUENCE |
|
|
|
| |
xstInstancePortInstance |
Integer32 |
|
| |
xstInstancePortPort |
Integer32 |
|
| |
xstInstancePortPriority |
Integer32 |
|
| |
xstInstancePortState |
INTEGER |
|
| |
xstInstancePortEnable |
EnabledStatus |
|
| |
xstInstancePortPathCost |
Integer32 |
|
| |
xstInstancePortDesignatedRoot |
BridgeId |
|
| |
xstInstancePortDesignatedCost |
Integer32 |
|
| |
xstInstancePortDesignatedBridge |
BridgeId |
|
| |
xstInstancePortDesignatedPort |
OCTET STRING |
|
| |
xstInstancePortForwardTransitions |
Counter32 |
|
| |
xstInstancePortPortRole |
INTEGER |
|
| MirrorEntry |
|
| SEQUENCE |
|
|
|
| |
mirrorDestinationPort |
Integer32 |
|
| |
mirrorSourcePort |
Integer32 |
|
| |
mirrorType |
INTEGER |
|
| |
mirrorStatus |
INTEGER |
|
| IgmpSnoopRouterCurrentEntry |
|
| SEQUENCE |
|
|
|
| |
igmpSnoopRouterCurrentVlanIndex |
Unsigned32 |
|
| |
igmpSnoopRouterCurrentPorts |
PortList |
|
| |
igmpSnoopRouterCurrentStatus |
PortList |
|
| IgmpSnoopRouterStaticEntry |
|
| SEQUENCE |
|
|
|
| |
igmpSnoopRouterStaticVlanIndex |
Unsigned32 |
|
| |
igmpSnoopRouterStaticPorts |
PortList |
|
| |
igmpSnoopRouterStaticStatus |
INTEGER |
|
| IgmpSnoopMulticastCurrentEntry |
|
| SEQUENCE |
|
|
|
| |
igmpSnoopMulticastCurrentVlanIndex |
Unsigned32 |
|
| |
igmpSnoopMulticastCurrentIpAddress |
IpAddress |
|
| |
igmpSnoopMulticastCurrentPorts |
PortList |
|
| |
igmpSnoopMulticastCurrentStatus |
PortList |
|
| IgmpSnoopMulticastStaticEntry |
|
| SEQUENCE |
|
|
|
| |
igmpSnoopMulticastStaticVlanIndex |
Unsigned32 |
|
| |
igmpSnoopMulticastStaticIpAddress |
IpAddress |
|
| |
igmpSnoopMulticastStaticPorts |
PortList |
|
| |
igmpSnoopMulticastStaticStatus |
INTEGER |
|
| NetConfigEntry |
|
| SEQUENCE |
|
|
|
| |
netConfigIfIndex |
Integer32 |
|
| |
netConfigIPAddress |
IpAddress |
|
| |
netConfigSubnetMask |
IpAddress |
|
| |
netConfigPrimaryInterface |
INTEGER |
|
| |
netConfigUnnumbered |
INTEGER |
|
| |
netConfigStatus |
RowStatus |
|
| BcastStormEntry |
|
| SEQUENCE |
|
|
|
| |
bcastStormIfIndex |
Integer32 |
|
| |
bcastStormStatus |
INTEGER |
|
| |
bcastStormSampleType |
INTEGER |
|
| |
bcastStormPktRate |
INTEGER |
|
| |
bcastStormOctetRate |
INTEGER |
|
| |
bcastStormPercent |
INTEGER |
|
| VlanEntry |
|
| SEQUENCE |
|
|
|
| |
vlanIndex |
Unsigned32 |
|
| |
vlanAddressMethod |
INTEGER |
|
| VlanPortEntry |
|
| SEQUENCE |
|
|
|
| |
vlanPortIndex |
Integer32 |
|
| |
vlanPortMode |
INTEGER |
|
| PrioIpPrecEntry |
|
| SEQUENCE |
|
|
|
| |
prioIpPrecPort |
Integer32 |
|
| |
prioIpPrecValue |
Integer32 |
|
| |
prioIpPrecCos |
INTEGER |
|
| PrioIpDscpEntry |
|
| SEQUENCE |
|
|
|
| |
prioIpDscpPort |
Integer32 |
|
| |
prioIpDscpValue |
Integer32 |
|
| |
prioIpDscpCos |
INTEGER |
|
| PrioIpPortEntry |
|
| SEQUENCE |
|
|
|
| |
prioIpPortPhysPort |
Integer32 |
|
| |
prioIpPortValue |
Integer32 |
|
| |
prioIpPortCos |
INTEGER |
|
| |
prioIpPortStatus |
INTEGER |
|
| PrioWrrEntry |
|
| SEQUENCE |
|
|
|
| |
prioWrrTrafficClass |
INTEGER |
|
| |
prioWrrWeight |
INTEGER |
|
| TrapDestEntry |
|
| SEQUENCE |
|
|
|
| |
trapDestAddress |
IpAddress |
|
| |
trapDestCommunity |
OCTET STRING |
|
| |
trapDestStatus |
INTEGER |
|
| |
trapDestVersion |
INTEGER |
|
| PortSecPortEntry |
|
| SEQUENCE |
|
|
|
| |
portSecPortIndex |
Integer32 |
|
| |
portSecPortStatus |
EnabledStatus |
|
| |
portSecAction |
INTEGER |
|
| SshConnInfoEntry |
|
| SEQUENCE |
|
|
|
| |
sshConnID |
Integer32 |
|
| |
sshConnMajorVersion |
Integer32 |
|
| |
sshConnMinorVersion |
Integer32 |
|
| |
sshConnStatus |
INTEGER |
|
| |
sshConnEncryptionType |
INTEGER |
|
| |
sshConnUserName |
OCTET STRING |
|
| |
sshDisconnect |
INTEGER |
|
| RemoteLogServerEntry |
|
| SEQUENCE |
|
|
|
| |
remoteLogServerIp |
IpAddress |
|
| |
remoteLogServerStatus |
ValidStatus |
|
Defined Values
| private |
1.3.6.1.4 |
| OBJECT IDENTIFIER |
|
|
|
| dell |
1.3.6.1.4.1.674 |
| OBJECT IDENTIFIER |
|
|
|
| dellLan |
1.3.6.1.4.1.674.10895 |
| OBJECT IDENTIFIER |
|
|
|
| powerConnect3248MIB |
1.3.6.1.4.1.674.10895.3 |
| The private MIB module definition for the Dell
PowerConnect 3248 Network Switch. |
| MODULE-IDENTITY |
|
|
|
| switchMgt |
1.3.6.1.4.1.674.10895.3.1.1 |
| OBJECT IDENTIFIER |
|
|
|
| portMgt |
1.3.6.1.4.1.674.10895.3.1.2 |
| OBJECT IDENTIFIER |
|
|
|
| trunkMgt |
1.3.6.1.4.1.674.10895.3.1.3 |
| OBJECT IDENTIFIER |
|
|
|
| lacpMgt |
1.3.6.1.4.1.674.10895.3.1.4 |
| OBJECT IDENTIFIER |
|
|
|
| staMgt |
1.3.6.1.4.1.674.10895.3.1.5 |
| OBJECT IDENTIFIER |
|
|
|
| tftpMgt |
1.3.6.1.4.1.674.10895.3.1.6 |
| OBJECT IDENTIFIER |
|
|
|
| restartMgt |
1.3.6.1.4.1.674.10895.3.1.7 |
| OBJECT IDENTIFIER |
|
|
|
| mirrorMgt |
1.3.6.1.4.1.674.10895.3.1.8 |
| OBJECT IDENTIFIER |
|
|
|
| ipMgt |
1.3.6.1.4.1.674.10895.3.1.10 |
| OBJECT IDENTIFIER |
|
|
|
| vlanMgt |
1.3.6.1.4.1.674.10895.3.1.12 |
| OBJECT IDENTIFIER |
|
|
|
| priorityMgt |
1.3.6.1.4.1.674.10895.3.1.13 |
| OBJECT IDENTIFIER |
|
|
|
| trapDestMgt |
1.3.6.1.4.1.674.10895.3.1.14 |
| OBJECT IDENTIFIER |
|
|
|
| securityMgt |
1.3.6.1.4.1.674.10895.3.1.17 |
| OBJECT IDENTIFIER |
|
|
|
| sysLogMgt |
1.3.6.1.4.1.674.10895.3.1.19 |
| OBJECT IDENTIFIER |
|
|
|
| lineMgt |
1.3.6.1.4.1.674.10895.3.1.20 |
| OBJECT IDENTIFIER |
|
|
|
| switchManagementVlan |
1.3.6.1.4.1.674.10895.3.1.1.1 |
| The VLAN on which management is done. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..4094 |
|
| switchNumber |
1.3.6.1.4.1.674.10895.3.1.1.2 |
| The total number of switches present on this system. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| switchInfoTable |
1.3.6.1.4.1.674.10895.3.1.1.3 |
| Table of descriptive and status information about
switches in this system. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
SwitchInfoEntry |
|
| switchInfoEntry |
1.3.6.1.4.1.674.10895.3.1.1.3.1 |
| An entry in the table, containing information
about a single switch in this system. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SwitchInfoEntry |
|
|
| swUnitIndex |
1.3.6.1.4.1.674.10895.3.1.1.3.1.1 |
| This object identifies the switch within the system
for which this entry contains information. This
value can never be greater than switchNumber. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| swHardwareVer |
1.3.6.1.4.1.674.10895.3.1.1.3.1.2 |
| Hardware version of the main board. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
Size(0..20) |
|
| swMicrocodeVer |
1.3.6.1.4.1.674.10895.3.1.1.3.1.3 |
| Microcode version of the main board. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
Size(0..20) |
|
| swLoaderVer |
1.3.6.1.4.1.674.10895.3.1.1.3.1.4 |
| Loader version of the main board. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
Size(0..20) |
|
| swBootRomVer |
1.3.6.1.4.1.674.10895.3.1.1.3.1.5 |
| Boot ROM code version of the main board. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
Size(0..20) |
|
| swOpCodeVer |
1.3.6.1.4.1.674.10895.3.1.1.3.1.6 |
| Operation code version of the main board. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
Size(0..20) |
|
| swPortNumber |
1.3.6.1.4.1.674.10895.3.1.1.3.1.7 |
| The total port number of this switch
(including expansion slot). |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| swPowerStatus |
1.3.6.1.4.1.674.10895.3.1.1.3.1.8 |
| Indicates the switch using internalPower(1),
redundantPower(2) or both(3) |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
internalPower(1), redundantPower(2), internalAndRedundantPower(3) |
|
| swRoleInSystem |
1.3.6.1.4.1.674.10895.3.1.1.3.1.9 |
| Indicates the switch is master(1), backupMaster(2)
or slave(3) in this system. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
master(1), backupMaster(2), slave(3) |
|
| swSerialNumber |
1.3.6.1.4.1.674.10895.3.1.1.3.1.10 |
| Serial number of the switch. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
Size(0..80) |
|
| swExpansionSlot1 |
1.3.6.1.4.1.674.10895.3.1.1.3.1.11 |
| Type of expansion module in this switch slot 1. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
notPresent(1), other(2), hundredBaseFxScMmf(3), hundredBaseFxScSmf(4), hundredBaseFxMtrjMmf(5), thousandBaseSxScMmf(6), thousandBaseSxMtrjMmf(7), thousandBaseXGbic(8), thousandBaseLxScSmf(9), thousandBaseT(10), stackingModule(11), thousandBaseSfp(12) |
|
| swExpansionSlot2 |
1.3.6.1.4.1.674.10895.3.1.1.3.1.12 |
| Type of expansion module in this switch slot 2. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
notPresent(1), other(2), hundredBaseFxScMmf(3), hundredBaseFxScSmf(4), hundredBaseFxMtrjMmf(5), thousandBaseSxScMmf(6), thousandBaseSxMtrjMmf(7), thousandBaseXGbic(8), thousandBaseLxScSmf(9), thousandBaseT(10), stackingModule(11), thousandBaseSfp(12) |
|
| swServiceTag |
1.3.6.1.4.1.674.10895.3.1.1.3.1.13 |
| Service tag serial-number of the switch. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
Size(0..80) |
|
| switchOperState |
1.3.6.1.4.1.674.10895.3.1.1.4 |
| Global operation state of the switch. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
other(1), unknown(2), ok(3), noncritical(4), critical(5), nonrecoverable(6) |
|
| swProdName |
1.3.6.1.4.1.674.10895.3.1.1.5.1 |
| Tok_String |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
Size(0..127) |
|
| swProdUrl |
1.3.6.1.4.1.674.10895.3.1.1.5.5 |
| Tok_String |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
Size(0..127) |
|
| swIdentifier |
1.3.6.1.4.1.674.10895.3.1.1.5.6 |
| A unique identifier of which switch in the chassis is currently
being looked at. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| swChassisServiceTag |
1.3.6.1.4.1.674.10895.3.1.1.5.7 |
| The service tag of the chassis this switch resides in. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
Size(0..80) |
|
| switchIndivPowerEntry |
1.3.6.1.4.1.674.10895.3.1.1.6.1 |
| Table about statuses of individual powers. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SwitchIndivPowerEntry |
|
|
| swIndivPowerIndex |
1.3.6.1.4.1.674.10895.3.1.1.6.1.2 |
| 1 means internal power. 2 means external power. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..2 |
|
| swIndivPowerStatus |
1.3.6.1.4.1.674.10895.3.1.1.6.1.3 |
| notPresent(1) means not present. green(2) means
up. red(3) means down. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
notPresent(1), green(2), red(3) |
|
| portTable |
1.3.6.1.4.1.674.10895.3.1.2.1 |
| Table of descriptive and status information about
configuration of each switch port (including expansion slot)
in this system. This table also contains information
about each trunk (similar to Cisco's EtherChannel). |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
PortEntry |
|
| portEntry |
1.3.6.1.4.1.674.10895.3.1.2.1.1 |
| An entry in the table, containing information
about configuration in one switch port of the switch. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
PortEntry |
|
|
| portIndex |
1.3.6.1.4.1.674.10895.3.1.2.1.1.1 |
| This is defined as ifIndex in the IF-MIB. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| portName |
1.3.6.1.4.1.674.10895.3.1.2.1.1.2 |
| Indicates the port name. This is same as
ifAlias in the IF-MIB (RFC2863 or later). |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
Size(0..64) |
|
| portType |
1.3.6.1.4.1.674.10895.3.1.2.1.1.3 |
| Indicates the port type. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
other(1), hundredBaseTX(2), hundredBaseFX(3), thousandBaseSX(4), thousandBaseLX(5), thousandBaseT(6), thousandBaseGBIC(7), thousandBaseSfp(8) |
|
| portSpeedDpxCfg |
1.3.6.1.4.1.674.10895.3.1.2.1.1.4 |
| Set the port speed and duplex mode as follows:
halfDuplex10(2) - 10Mbps and half duplex mode
fullDuplex10(3) - 10Mbps and full duplex mode
halfDuplex100(4) - 100Mbps and half duplex mode
fullDuplex100(5) - 100Mbps and full duplex mode
halfDuplex1000(6) - 1000Mbps and half duplex mode
fullDuplex1000(7) - 1000Mbps and full duplex mode
hundredBaseTX port can be set as
halfDuplex10(2)
fullDuplex10(3)
halfDuplex100(4)
fullDuplex100(5)
hundredBaseFX port can be set as
halfDuplex100(4)
fullDuplex100(5)
thousandBaseSX port can be set as
halfDuplex1000(6)
fullDuplex1000(7)
The actual operating speed and duplex of the port
is given by portSpeedDpxStatus. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
reserved(1), halfDuplex10(2), fullDuplex10(3), halfDuplex100(4), fullDuplex100(5), halfDuplex1000(6), fullDuplex1000(7) |
|
| portFlowCtrlCfg |
1.3.6.1.4.1.674.10895.3.1.2.1.1.5 |
| (1) Flow control mechanism is enabled.
If the port type is hundredBaseTX or thousandBaseSX:
When the port is operating in halfDuplex mode, the
port uses backPressure flow control mechanism. When
the port is operating in fullDuplex mode, the port
uses IEEE 802.3x flow control mechanism.
If the port type is hundredBaseFX:
When the port is operating in halfDuplex mode, the
port uses backPressure flow control mechanism. When
the port is operating in fullDuplex mode, Flow
control mechanism will not function.
(2) Flow control mechanism is disabled.
(3) Flow control mechanism is backPressure.
when the port is in fullDuplex mode.This flow control
mechanism will not function.
(4) Flow control mechanism is IEEE 802.3x flow control.
when the port is in halfDuplex mode.This flow control
mechanism will not function.
hundredBaseTX and thousandBaseSX port can be set as:
enabled(1),
disabled(2),
backPressure(3),
dot3xFlowControl(4).
hundredBaseFX port can be set as:
enabled(1),
disabled(2),
backPressure(3).
The actual flow control mechanism is used given by
portFlowCtrlStatus. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2), backPressure(3), dot3xFlowControl(4) |
|
| portCapabilities |
1.3.6.1.4.1.674.10895.3.1.2.1.1.6 |
| Port capabilities. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
BITS |
portCap10half(0), portCap10full(1), portCap100half(2), portCap100full(3), portCap1000half(4), portCap1000full(5), reserved6(6), reserved7(7), reserved8(8), reserved9(9), reserved10(10), reserved11(11), reserved12(12), reserved13(13), portCapSym(14), portCapFlowCtrl(15) |
|
| portAutonegotiation |
1.3.6.1.4.1.674.10895.3.1.2.1.1.7 |
| Whether autonegotiation is enabled. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| portSpeedDpxStatus |
1.3.6.1.4.1.674.10895.3.1.2.1.1.8 |
| The operating speed and duplex mode of the
switched port. If this index is a trunk,
the speed is the speed of its individual members.
If this index is a trunk and the result
is inconsistent among its member ports, this value is
error(1). |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
error(1), halfDuplex10(2), fullDuplex10(3), halfDuplex100(4), fullDuplex100(5), halfDuplex1000(6), fullDuplex1000(7) |
|
| portFlowCtrlStatus |
1.3.6.1.4.1.674.10895.3.1.2.1.1.9 |
| (2) BackPressure flow control machanism is used.
(3) IEEE 802.3 flow control machanism is used.
(4) Flow control mechanism is disabled.
If this index is a trunk and the result
is inconsistent among its member ports, this value is
error(1). |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
error(1), backPressure(2), dot3xFlowControl(3), none(4) |
|
| portTrunkIndex |
1.3.6.1.4.1.674.10895.3.1.2.1.1.10 |
| The trunk to which this port belongs. A value of 0
means that this port does not belong to any trunk.
A value greater than zero means that this port
belongs to trunk at trunkIndex, defined by the
corresponding trunkPorts. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| trunkMaxId |
1.3.6.1.4.1.674.10895.3.1.3.1 |
| The maximum number for a trunk identifier. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| trunkValidNumber |
1.3.6.1.4.1.674.10895.3.1.3.2 |
| The number of valid trunks. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| trunkTable |
1.3.6.1.4.1.674.10895.3.1.3.3 |
| Table of descriptive and status information about
configuration of each trunk,
similar to Cisco EtherChannel. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
TrunkEntry |
|
| trunkEntry |
1.3.6.1.4.1.674.10895.3.1.3.3.1 |
| An entry in the table, containing information
about configuration in one trunk of the switch. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
TrunkEntry |
|
|
| trunkIndex |
1.3.6.1.4.1.674.10895.3.1.3.3.1.1 |
| This object identifies the trunk within the switch
for which this entry contains information. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| trunkPorts |
1.3.6.1.4.1.674.10895.3.1.3.3.1.2 |
| The complete set of ports currently associated with
this trunk. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
PortList |
|
|
| trunkCreation |
1.3.6.1.4.1.674.10895.3.1.3.3.1.3 |
| A value of static(1) means a statically configured trunk.
A value of lacp(2) means an LACP-configured trunk. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
static(1), lacp(2) |
|
| trunkStatus |
1.3.6.1.4.1.674.10895.3.1.3.3.1.4 |
| Writing this to valid(1) creates an entry.
Writing this to invalid(2) destroys an entry. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
valid(1), invalid(2) |
|
| lacpPortTable |
1.3.6.1.4.1.674.10895.3.1.4.1 |
| Table for LACP port configuration. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
LacpPortEntry |
|
| lacpPortEntry |
1.3.6.1.4.1.674.10895.3.1.4.1.1 |
| Entry for LACP port configuration. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
LacpPortEntry |
|
|
| lacpPortIndex |
1.3.6.1.4.1.674.10895.3.1.4.1.1.1 |
| This is defined as ifIndex in the IF-MIB. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| lacpPortStatus |
1.3.6.1.4.1.674.10895.3.1.4.1.1.2 |
| Whether 802.3ad LACP is enabled. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| staSystemStatus |
1.3.6.1.4.1.674.10895.3.1.5.1 |
| Global spanning tree status.
(1) Spanning tree protocol is enabled.
(2) Spanning tree protocol is disabled. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
EnabledStatus |
|
|
| staPortTable |
1.3.6.1.4.1.674.10895.3.1.5.2 |
| The table manages port settings for Spanning Tree
Protocol 802.1d, 802.1w or 802.1s depending on the
value specified by staProtocolType. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
StaPortEntry |
|
| staPortEntry |
1.3.6.1.4.1.674.10895.3.1.5.2.1 |
| The conceptual entry of staPortTable. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
StaPortEntry |
|
|
| staPortIndex |
1.3.6.1.4.1.674.10895.3.1.5.2.1.1 |
| The port and the trunk (excluding trunk member ports)
interface of the staPortTable. The interface identified
by a particular value of this index is the same interface
as identified by the same value of dot1dStpPort in the
BRIDGE-MIB. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| staPortProtocolMigration |
1.3.6.1.4.1.674.10895.3.1.5.2.1.3 |
| When operating in RSTP (version 2) mode, writing TRUE(1)
to this object forces this port to transmit RSTP BPDUs.
Any other operation on this object has no effect and
it always returns FALSE(2) when read. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
TruthValue |
|
|
| staPortAdminEdgePort |
1.3.6.1.4.1.674.10895.3.1.5.2.1.4 |
| The administrative value of the Edge Port parameter. A
value of TRUE(1) indicates that this port should be
assumed as an edge-port and a value of FALSE(2) indicates
that this port should be assumed as a non-edge-port. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
TruthValue |
|
|
| staPortOperEdgePort |
1.3.6.1.4.1.674.10895.3.1.5.2.1.5 |
| The operational value of the Edge Port parameter. The object is
initialized to the value of staPortAdminEdgePort and is set FALSE
when a BPDU is received. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
TruthValue |
|
|
| staPortAdminPointToPoint |
1.3.6.1.4.1.674.10895.3.1.5.2.1.6 |
| The administrative point-to-point status of the LAN segment
attached to this port. A value of forceTrue(0) indicates that
this port should always be treated as if it is connected to
a point-to-point link. A value of forceFalse(1) indicates
that this port should be treated as having a shared media
connection. A value of auto(2) indicates that this port is
considered to have a point-to-point link if it is an Aggregator
and all of its members are aggregatable, or if the MAC entity
is configured for full duplex operation, either through
auto-negotiation or by management means. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
forceTrue(0), forceFalse(1), auto(2) |
|
| staPortOperPointToPoint |
1.3.6.1.4.1.674.10895.3.1.5.2.1.7 |
| The operational point-to-point status of the LAN segment
attached to this port. It indicates whether a port is
considered to have a point-to-point connection or not.
The value is determined by management or by auto-detection,
as described in the staPortAdminPointToPoint object. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
TruthValue |
|
|
| staPortLongPathCost |
1.3.6.1.4.1.674.10895.3.1.5.2.1.8 |
| The contribution of this port to the path cost (in 32
bits value) of paths towards the spanning tree root which
include this port.
This object is used to configure the spanning tree port
path cost in 32 bits value range when the
staPathCostMethod is long(2).
If the staPathCostMethod is short(1), this mib object is not
instantiated. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
1..200000000 |
|
| staProtocolType |
1.3.6.1.4.1.674.10895.3.1.5.3 |
| The version of Spanning Tree Protocol the bridge is currently
running. The value 'stp(1)' indicates the Spanning Tree
Protocol is as specified in IEEE 802.1D,'rstp(2)' indicates
the Rapid Spanning Tree Protocol is as specified in IEEE
802.1w and the value 'mstp(3)' indicates the Multiple Spanning
Tree Protocol is as specified in IEEE 802.1s. New values may
be defined in the future as new or updated versions of the
protocol become available. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
stp(1), rstp(2), mstp(3) |
|
| staTxHoldCount |
1.3.6.1.4.1.674.10895.3.1.5.4 |
| The value used by the Port Transmit state machine to limit
the maximum transmission rate. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
1..10 |
|
| staPathCostMethod |
1.3.6.1.4.1.674.10895.3.1.5.5 |
| Indicates the type of spanning tree path cost mode configured
on the switch. This mode applies to all instances of the
Spanning tree protocol running on the switch.
When the value of this MIB object is changed, the path cost of
all ports will be reassigned to the default path cost values
based on the new spanning tree path cost mode and the
ports' speed.
When the value of this MIB object is set to long(2), the
staPortLongPathCost MIB object must be used to retrieve/configure
the spanning tree port path cost as a 32 bit value. The set
operation on dot1dStpPortPathCost in BRIDGE-MIB will be rejected.
While retrieving the value of dot1dStpPortPathCost, the maximum
value of 65535 will be returned if the value of staPortLongPathCost
for the same instance exceeds 65535.
When the value of this MIB object is set to short(1), the
dot1dStpPortPathCost in BRIDGE-MIB must be used. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
short(1), long(2) |
|
| xstMgt |
1.3.6.1.4.1.674.10895.3.1.5.6 |
| OBJECT IDENTIFIER |
|
|
|
| xstInstanceCfgTable |
1.3.6.1.4.1.674.10895.3.1.5.6.4 |
| This table is used to configure the property of a specific
instance in Multiple Spanning Tree or Rapid Spanning Tree.
If Rapid Spanning Tree protocol is in use, the
mstInstanceEditIndex is always 0. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
XstInstanceCfgEntry |
|
| xstInstanceCfgEntry |
1.3.6.1.4.1.674.10895.3.1.5.6.4.1 |
| A conceptual row containing the property of the MST or RST instance. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
XstInstanceCfgEntry |
|
|
| xstInstanceCfgIndex |
1.3.6.1.4.1.674.10895.3.1.5.6.4.1.1 |
| An arbitrary integer within the range from 1 to the value of
the maximum instance that uniquely identifies a spanning
tree instance. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
1..64 |
|
| xstInstanceCfgPriority |
1.3.6.1.4.1.674.10895.3.1.5.6.4.1.2 |
| The priority of a specific spanning tree instance.
The value assigned should be in the range 0-61440
in steps of 4096. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..61440 |
|
| xstInstanceCfgTimeSinceTopologyChange |
1.3.6.1.4.1.674.10895.3.1.5.6.4.1.3 |
| The time (in hundredths of second) since the last topology
change detected by the bridge entity in MST or RST. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| xstInstanceCfgTopChanges |
1.3.6.1.4.1.674.10895.3.1.5.6.4.1.4 |
| The total number of topology changes detected by
this bridge in MST or RST since the management entity
was last reset or initialized. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| xstInstanceCfgDesignatedRoot |
1.3.6.1.4.1.674.10895.3.1.5.6.4.1.5 |
| The bridge identifier of the root of the spanning
tree as determined by the Multiple Spanning Tree Protocol (1s)
or Rapid Spanning Tree Protocol (1w) executed by this node.
This value is used as the Root Identifier parameter in
all Configuration Bridge PDUs originated by this node. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
BridgeId |
|
|
| xstInstanceCfgRootCost |
1.3.6.1.4.1.674.10895.3.1.5.6.4.1.6 |
| The cost of the path to the root as seen from
this bridge of the MST or RST. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| xstInstanceCfgRootPort |
1.3.6.1.4.1.674.10895.3.1.5.6.4.1.7 |
| The number of the port which offers the
lowest cost path from this bridge to the root
bridge of the MST or RST. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| xstInstanceCfgMaxAge |
1.3.6.1.4.1.674.10895.3.1.5.6.4.1.8 |
| The maximum age of Multiple Spanning Tree Protocol (1s)
or Rapid Spanning Tree Protocol (1w) information learned
from the network on any port before it is discarded,
in units of hundredths of a second. This is the actual
value that this bridge is currently using. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Timeout |
|
|
| xstInstanceCfgHelloTime |
1.3.6.1.4.1.674.10895.3.1.5.6.4.1.9 |
| The amount of time between the transmission of
Configuration bridge PDUs by this node on any port
when it is the root of the specific spanning tree or trying
to become so, in units of hundredths of a second.
This is the actual value that this bridge is
currently using in MST or RST. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Timeout |
|
|
| xstInstanceCfgHoldTime |
1.3.6.1.4.1.674.10895.3.1.5.6.4.1.10 |
| This time value determines the interval length
during which no more than two Configuration bridge
PDUs shall be transmitted by this node, in units
of hundredths of a second. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Timeout |
|
|
| xstInstanceCfgForwardDelay |
1.3.6.1.4.1.674.10895.3.1.5.6.4.1.11 |
| For MST or RST protocol, this time value, measured in units of
hundredths of a second, controls how fast a port changes
its spanning state when moving towards the Forwarding
state. The value determines how long the port
stays in each of the Listening and Learning
states, which precede the Forwarding state. This
value is also used, when a topology change has
been detected and is underway, to age all dynamic
entries in the Forwarding Database. This value is the
current value being used by the bridge.
xstInstanceCfgBridgeForwardDelay defines the value that
this bridge and all others would start using
if/when this bridge were to become the root. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Timeout |
|
|
| xstInstanceCfgBridgeMaxAge |
1.3.6.1.4.1.674.10895.3.1.5.6.4.1.12 |
| For MST or RST protocol, the time (in hundredths of second)
that all bridges use for MaxAge when this bridge is acting
as the root. Note that 802.1D-1990 specifies that the range
for this parameter is related to the value of
xstInstanceCfgBridgeHelloTime. The granularity of this
timer is specified by 802.1D-1990 to be 1 second. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Timeout |
|
|
| xstInstanceCfgBridgeHelloTime |
1.3.6.1.4.1.674.10895.3.1.5.6.4.1.13 |
| For MST or RST protocol,the time (in hundredths of second) that
all bridges use for HelloTime when this bridge is acting
as the root. The granularity of this timer is specified
by 802.1D-1990 to be 1 second. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Timeout |
|
|
| xstInstanceCfgBridgeForwardDelay |
1.3.6.1.4.1.674.10895.3.1.5.6.4.1.14 |
| For MST or RST protocol, the time (in hundredths of second)
that all bridges use for ForwardDelay when this bridge
is acting as the root.
Note that 802.1D-1990 specifies that the range for this
parameter is related to the value of
xstInstanceCfgBridgeMaxAge. The granularity of this
timer is specified by 802.1D-1990 to be 1 second. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Timeout |
|
|
| xstInstanceCfgTxHoldCount |
1.3.6.1.4.1.674.10895.3.1.5.6.4.1.15 |
| For MST or RST protocol, the value used by the Port Transmit
state machine to limit the maximum transmission rate. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| xstInstanceCfgPathCostMethod |
1.3.6.1.4.1.674.10895.3.1.5.6.4.1.16 |
| For MST or RST protocol, this indicates the type of spanning tree path
cost mode used by the switch. The mode applies to all instances of the
Spanning Tree protocol running on the switch.
When the value of this MIB object is changed, the path cost
of all ports will be reassigned to the default path cost
values based on the new spanning tree path cost mode and the
ports' speed.
When the value of this MIB object is set to long(2),
the xstInstancePortPathCost MIB object must be used in order
to retrieve/configure the spanning tree port path cost as a
32 bit value. The set operation on dot1dStpPortPathCost in
BRIDGE-MIB will be rejected. While retrieving the value of
dot1dStpPortPathCost, the maximum value of 65535 will be
returned if the value of xstInstancePortPathCost for the same
instance exceeds 65535.
When the value of this MIB object is set to short(1),
the dot1dStpPortPathCost in BRIDGE-MIB must be used. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
short(1), long(2) |
|
| xstInstancePortTable |
1.3.6.1.4.1.674.10895.3.1.5.6.5 |
| The extension table for dot1dStpPortEntry to provide
additional Spanning Tree information and configuration. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
XstInstancePortEntry |
|
| xstInstancePortEntry |
1.3.6.1.4.1.674.10895.3.1.5.6.5.1 |
| The conceptual row for xstInstancePortTable. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
XstInstancePortEntry |
|
|
| xstInstancePortPort |
1.3.6.1.4.1.674.10895.3.1.5.6.5.1.2 |
| The port and the trunk (excluding trunk member ports)
interface of the mstInstancePortTable. The interface identified
by a particular value of this index is the same interface
as identified by the same value of dot1dStpPort in the BRIDGE-MIB. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| xstInstancePortPriority |
1.3.6.1.4.1.674.10895.3.1.5.6.5.1.3 |
| Defines the priority used for this port in the Spanning
Tree Algorithm. If the path cost for all ports on a
switch is the same, the port with the highest priority
(i.e., lowest value) will be configured as an active link
in the Spanning Tree. This makes a port with higher
priority less likely to be blocked if the Spanning Tree
Algorithm is detecting network loops. Where more than one
port is assigned the highest priority, the port with
lowest numeric identifier will be enabled. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..240 |
|
| xstInstancePortState |
1.3.6.1.4.1.674.10895.3.1.5.6.5.1.4 |
| The port's current state as defined by application of
the Spanning Tree Protocol. This state controls what
action a port takes on reception of a frame:
discarding(1) Port receives configuration messages,
but does not forward packets.
learning(2) Port has transmitted configuration messages
for an interval set by the Forward Delay
parameter without receiving contradictory
information. Port address table is cleared,
and the port begins learning addresses.
forwarding(3) Port forwards packets, and continues learning
addresses.
For ports which are disabled (see xstInstancePortEnable),
this object will have a value of discarding(1). |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
discarding(1), learning(2), forwarding(3) |
|
| xstInstancePortPathCost |
1.3.6.1.4.1.674.10895.3.1.5.6.5.1.6 |
| The pathcost of the MST or RST in the range 1 to 200000000.
This parameter is used to determine the best path between
devices. Therefore, lower values should be assigned to
ports attached to faster media, and higher values assigned
to ports with slower media. (Path cost takes precedence
over port priority). |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
1..200000000 |
|
| xstInstancePortDesignatedRoot |
1.3.6.1.4.1.674.10895.3.1.5.6.5.1.7 |
| The unique Bridge Identifier of the Bridge
recorded as the Root in the Configuration BPDUs
transmitted by the Designated Bridge for the
segment to which the port is attached. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
BridgeId |
|
|
| xstInstancePortDesignatedCost |
1.3.6.1.4.1.674.10895.3.1.5.6.5.1.8 |
| The path cost of the Designated Port of the
segment connected to this port. This value is
compared to the Root Path Cost field in received
bridge PDUs. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| xstInstancePortDesignatedBridge |
1.3.6.1.4.1.674.10895.3.1.5.6.5.1.9 |
| The Bridge Identifier of the bridge which this
port considers to be the Designated Bridge for
this port's segment. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
BridgeId |
|
|
| xstInstancePortDesignatedPort |
1.3.6.1.4.1.674.10895.3.1.5.6.5.1.10 |
| The Port Identifier of the port on the Designated
Bridge for this port's segment. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
OCTET STRING |
Size(2) |
|
| xstInstancePortForwardTransitions |
1.3.6.1.4.1.674.10895.3.1.5.6.5.1.11 |
| The number of times this port has transitioned
from the Learning state to the Forwarding state. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| xstInstancePortPortRole |
1.3.6.1.4.1.674.10895.3.1.5.6.5.1.12 |
| The role of the port in the MST or RST protocol:
(1) The port has no role within the spanning tree
(2) The port is part of the active topology connecting
the bridge to the root bridge (i.e., root port)
(3) The port is connecting a LAN through the bridge to the
root bridge (i.e., designated port)
(4) The port may provide connectivity if other
bridges, bridge ports, or LANs fail or are removed.
(5) The port provides backup if other
bridges, bridge ports, or LANs fail or are removed.
(6) For MST protocol only, indicated whether this instance
is in a master role. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
disabled(1), root(2), designated(3), alternate(4), backup(5), master(6) |
|
| tftpFileType |
1.3.6.1.4.1.674.10895.3.1.6.1 |
| Type of file to transfer. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
opcode(1), config(2) |
|
| tftpSrcFile |
1.3.6.1.4.1.674.10895.3.1.6.2 |
| The source file name for TFTP transfer when a
transfer is next requested via this MIB. This value is set to
the zero length string when no file name has been specified. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
Size(0..127) |
|
| tftpDestFile |
1.3.6.1.4.1.674.10895.3.1.6.3 |
| The destination file name for TFTP transfer when a
transfer is next requested via this MIB. This value is set to
the zero length string when no file name has been specified. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
Size(0..127) |
|
| tftpServer |
1.3.6.1.4.1.674.10895.3.1.6.4 |
| The IP address of the TFTP server for transfer
when a download is next requested via this MIB.
This value is set to `0.0.0.0' when no IP address has been
specified. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
IpAddress |
|
|
| tftpAction |
1.3.6.1.4.1.674.10895.3.1.6.5 |
| When this object is set to downloadToRAM(2) or
downloadToPROM(3), the device will discontinue its
normal operation and begin download of the file specified
by tftpSrcFile from the server specified by
tftpServer to tftpDestFile in the device
using the TFTP protocol. If
downloadToRAM(2) is specified, the new image is copied
to RAM only (the old image remains unaltered in the flash
EPROM). If downloadToPROM(3) is specified
the new image is written to the flash EPROM
memory after its checksum has been verified to be correct.
When the download process is completed, the device will
warm boot to restart the newly loaded application.
When the device is not downloading, this object will have
a value of notDownloading(1).
downloadToRAM(2) applies only to configuration download.
Otherwise 'invalid value' is replied.
When this object is set to upload(4), the device will begin
upload of the file specified by tftpScrFile in the device
to tftpDestFile in the server specified by tftpServer. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
notDownloading(1), downloadToPROM(2), downloadToRAM(3), upload(4) |
|
| tftpStatus |
1.3.6.1.4.1.674.10895.3.1.6.6 |
| The status of the last transfer procedure, if any. This
object will have a value of downloadStatusUnknown(2) if no
transfer process has been performed. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
tftpSuccess(1), tftpStatusUnknown(2), tftpGeneralError(3), tftpNoResponseFromServer(4), tftpDownloadChecksumError(5), tftpDownloadIncompatibleImage(6), tftpTftpFileNotFound(7), tftpTftpAccessViolation(8) |
|
| restartOpCodeFile |
1.3.6.1.4.1.674.10895.3.1.7.1 |
| Name of op-code file for start-up. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
Size(0..127) |
|
| restartConfigFile |
1.3.6.1.4.1.674.10895.3.1.7.2 |
| Name of configuration file for start-up. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
Size(0..127) |
|
| restartControl |
1.3.6.1.4.1.674.10895.3.1.7.3 |
| Setting this object to warmBoot(2) causes the device to
restart the application software with current configuration
parameters saved in non-volatile memory. Setting this
object to coldBoot(3) causes the device to reinitialize
configuration parameters in non-volatile memory to default
values and restart the application software. When the device
is running normally, this variable has a value of
running(1). |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
running(1), warmBoot(2), coldBoot(3) |
|
| mirrorTable |
1.3.6.1.4.1.674.10895.3.1.8.1 |
| Table of descriptive and status information about
switches in this system. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
MirrorEntry |
|
| mirrorEntry |
1.3.6.1.4.1.674.10895.3.1.8.1.1 |
| An entry in the table, containing information
about a single switch in this system. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
MirrorEntry |
|
|
| mirrorDestinationPort |
1.3.6.1.4.1.674.10895.3.1.8.1.1.1 |
| Destination port for mirrored packets. This is defined
as ifIndex in the IF-MIB. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| mirrorSourcePort |
1.3.6.1.4.1.674.10895.3.1.8.1.1.2 |
| Source port for mirrored packets. This is defined as
ifIndex in the IF-MIB. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| mirrorType |
1.3.6.1.4.1.674.10895.3.1.8.1.1.3 |
| If this value is rx(1), receive packets will
be mirrored. If this value is tx(2), transmit
packets will be mirrored. If this value is both(3),
both receive and transmit packets. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
rx(1), tx(2), both(3) |
|
| mirrorStatus |
1.3.6.1.4.1.674.10895.3.1.8.1.1.4 |
| Writing this to valid(1) creates an entry.
Writing this to invalid(2) destroys an entry. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
valid(1), invalid(2) |
|
| igmpSnoopStatus |
1.3.6.1.4.1.674.10895.3.1.9.1 |
| Parameter to enable or disable IGMP snooping on the device.
When enabled, the device will examine IGMP packets and set
up filters for IGMP ports. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| igmpSnoopQuerier |
1.3.6.1.4.1.674.10895.3.1.9.2 |
| Whether to act as querier. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| igmpSnoopQueryCount |
1.3.6.1.4.1.674.10895.3.1.9.3 |
| Maximum number of queries that have not been heard on the
system before the system starts taking action to solicit
reports. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
2..10 |
|
| igmpSnoopQueryInterval |
1.3.6.1.4.1.674.10895.3.1.9.4 |
| Query interval. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
60..125 |
|
| igmpSnoopQueryMaxResponseTime |
1.3.6.1.4.1.674.10895.3.1.9.5 |
| Timeout value (seconds) between IGMP reports received on a port
for an IP Multicast Address that can pass before the system
sends an IGMP Query out the port and removes it from the
list. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
5..30 |
|
| igmpSnoopQueryTimeout |
1.3.6.1.4.1.674.10895.3.1.9.6 |
| Query time-out. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
300..500 |
|
| igmpSnoopVersion |
1.3.6.1.4.1.674.10895.3.1.9.7 |
| Version. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..2 |
|
| igmpSnoopRouterCurrentEntry |
1.3.6.1.4.1.674.10895.3.1.9.8.1 |
| Entry for current router ports. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
IgmpSnoopRouterCurrentEntry |
|
|
| igmpSnoopRouterCurrentPorts |
1.3.6.1.4.1.674.10895.3.1.9.8.1.2 |
| The set of ports which are current router ports.
Within this list, some router ports are static router ports.
Please refer to igmpSnoopRouterStaticTable. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
PortList |
|
|
| igmpSnoopRouterStaticEntry |
1.3.6.1.4.1.674.10895.3.1.9.9.1 |
| Entry for static router ports. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
IgmpSnoopRouterStaticEntry |
|
|
| igmpSnoopRouterStaticStatus |
1.3.6.1.4.1.674.10895.3.1.9.9.1.3 |
| Writing this to valid(1) creates an entry.
Writing this to invalid(2) destroys an entry. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
valid(1), invalid(2) |
|
| igmpSnoopMulticastCurrentEntry |
1.3.6.1.4.1.674.10895.3.1.9.10.1 |
| Entry for current multicast addresses. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
IgmpSnoopMulticastCurrentEntry |
|
|
| igmpSnoopMulticastStaticEntry |
1.3.6.1.4.1.674.10895.3.1.9.11.1 |
| Entry for static multicast addresses. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
IgmpSnoopMulticastStaticEntry |
|
|
| igmpSnoopMulticastStaticStatus |
1.3.6.1.4.1.674.10895.3.1.9.11.1.4 |
| Writing this to valid(1) creates an entry.
Writing this to invalid(2) destroys an entry. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
valid(1), invalid(2) |
|
| netConfigTable |
1.3.6.1.4.1.674.10895.3.1.10.1 |
| A table of netConfigEntries. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
NetConfigEntry |
|
| netConfigEntry |
1.3.6.1.4.1.674.10895.3.1.10.1.1 |
| A set of configuration parameters for a particular
network interface on this device. If the device has no network
interface, this table is empty.
The index is composed of the ifIndex assigned to the
corresponding interface. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
NetConfigEntry |
|
|
| netConfigIfIndex |
1.3.6.1.4.1.674.10895.3.1.10.1.1.1 |
| VLAN interface on which this entry is defined.
This is defined as ifIndex in the IF-MIB. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| netConfigIPAddress |
1.3.6.1.4.1.674.10895.3.1.10.1.1.2 |
| The IP address of this Net interface. The default value
for this object is 0.0.0.0. If either the netConfigIPAddress
or netConfigSubnetMask are 0.0.0.0, then when the device
boots, it may use BOOTP to try to figure out what these
values should be. If BOOTP fails, before the device
can talk on the network, this value must be configured
(e.g., through a terminal attached to the device). If BOOTP is
used, care should be taken to not send BOOTP broadcasts too
frequently and to eventually send very infrequently if no
replies are received. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
IpAddress |
|
|
| netConfigSubnetMask |
1.3.6.1.4.1.674.10895.3.1.10.1.1.3 |
| The subnet mask of this Net interface. The default value
for this object is 0.0.0.0. If either the netConfigIPAddress
or netConfigSubnetMask are 0.0.0.0, then when the device
boots, it may use BOOTP to try to figure out what these
values should be. If BOOTP fails, before the device
can talk on the network, this value must be configured
(e.g., through a terminal attached to the device). If BOOTP is
used, care should be taken to not send BOOTP broadcasts too
frequently and to eventually send very infrequently if no
replies are received. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
IpAddress |
|
|
| netConfigPrimaryInterface |
1.3.6.1.4.1.674.10895.3.1.10.1.1.4 |
| Whether this is a primary interface. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
primary(1), secondary(2) |
|
| netConfigUnnumbered |
1.3.6.1.4.1.674.10895.3.1.10.1.1.5 |
| Whether this is an unnumbered interface. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
unnumbered(1), notUnnumbered(2) |
|
| netConfigStatus |
1.3.6.1.4.1.674.10895.3.1.10.1.1.6 |
| The status of this netConfigEntry.
An entry may not exist in the active state unless all
objects in the entry have an appropriate value. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
RowStatus |
|
|
| netDefaultGateway |
1.3.6.1.4.1.674.10895.3.1.10.2 |
| The IP Address of the default gateway. If this value is
undefined or unknown, it shall have the value 0.0.0.0. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
IpAddress |
|
|
| ipHttpState |
1.3.6.1.4.1.674.10895.3.1.10.3 |
| Whether HTTP is enabled. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| ipHttpPort |
1.3.6.1.4.1.674.10895.3.1.10.4 |
| The port number for HTTP. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..65535 |
|
| ipDhcpRestart |
1.3.6.1.4.1.674.10895.3.1.10.5 |
| Write it to restart(1) to restart DHCP.
When read, this value always returns noRestart(2). |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
restart(1), noRestart(2) |
|
| ipHttpsState |
1.3.6.1.4.1.674.10895.3.1.10.6 |
| Whether HTTPS is enabled. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
EnabledStatus |
|
|
| ipHttpsPort |
1.3.6.1.4.1.674.10895.3.1.10.7 |
| The port number for HTTPS. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
1..65535 |
|
| bcastStormTable |
1.3.6.1.4.1.674.10895.3.1.11.1 |
| Table of descriptive and status information about
configuration of each switch ports(including expansion slot)
in this system. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
BcastStormEntry |
|
| bcastStormEntry |
1.3.6.1.4.1.674.10895.3.1.11.1.1 |
| An entry in the table, containing information
about configuration in one switch port of the switch. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
BcastStormEntry |
|
|
| bcastStormIfIndex |
1.3.6.1.4.1.674.10895.3.1.11.1.1.1 |
| This is defined as ifIndex in the IF-MIB. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| bcastStormStatus |
1.3.6.1.4.1.674.10895.3.1.11.1.1.2 |
| Whether broadcast storm protection is enabled. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| bcastStormSampleType |
1.3.6.1.4.1.674.10895.3.1.11.1.1.3 |
| Sample type. If this is pkt-rate(1), then
bcastStormPktRate is valid. If this is octet-rate(2),
then bcastStormOctetRate is valid. If this is percent(3),
then bcastStormPercent is valid. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
pkt-rate(1), octet-rate(2), percent(3) |
|
| bcastStormPktRate |
1.3.6.1.4.1.674.10895.3.1.11.1.1.4 |
| Broadcast storm threshold as packets per second. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| bcastStormOctetRate |
1.3.6.1.4.1.674.10895.3.1.11.1.1.5 |
| Broadcast storm threshold as octets per second. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| bcastStormPercent |
1.3.6.1.4.1.674.10895.3.1.11.1.1.6 |
| Broadcast storm threshold as percentage of bandwidth. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| vlanTable |
1.3.6.1.4.1.674.10895.3.1.12.1 |
| Table for VLAN configuration. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
VlanEntry |
|
| vlanEntry |
1.3.6.1.4.1.674.10895.3.1.12.1.1 |
| Entry for VLAN configuration. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
VlanEntry |
|
|
| vlanIndex |
1.3.6.1.4.1.674.10895.3.1.12.1.1.1 |
| Same is dot1qVlanIndex in the Q-BRIDGE-MIB.
This table has only one entry - the entry for
the VLAN of the management interface. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| vlanAddressMethod |
1.3.6.1.4.1.674.10895.3.1.12.1.1.2 |
| Method to get the IP address. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
user(1), bootp(2), dhcp(3) |
|
| vlanPortTable |
1.3.6.1.4.1.674.10895.3.1.12.2 |
| Table for port configuration in VLAN. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
VlanPortEntry |
|
| vlanPortEntry |
1.3.6.1.4.1.674.10895.3.1.12.2.1 |
| Entry for port configuration in VLAN. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
VlanPortEntry |
|
|
| vlanPortIndex |
1.3.6.1.4.1.674.10895.3.1.12.2.1.1 |
| This is defined as ifIndex in the IF-MIB. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| vlanPortMode |
1.3.6.1.4.1.674.10895.3.1.12.2.1.2 |
| This variable sets the 802.1Q VLAN mode.
Setting it to hybrid(1) sets a hybrid link.
Setting it to dot1qTrunk(2) sets a trunk link.
Setting it to access(3) sets an access link. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
hybrid(1), dot1qTrunk(2), access(3) |
|
| prioIpPrecDscpStatus |
1.3.6.1.4.1.674.10895.3.1.13.1 |
| Whether IP precedence or DSCP look-up is enabled. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
disabled(1), precedence(2), dscp(3) |
|
| prioIpPrecTable |
1.3.6.1.4.1.674.10895.3.1.13.2 |
| Table for IP precedence priority mapping. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
PrioIpPrecEntry |
|
| prioIpPrecEntry |
1.3.6.1.4.1.674.10895.3.1.13.2.1 |
| Entry for IP precendence priority mapping. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
PrioIpPrecEntry |
|
|
| prioIpPrecPort |
1.3.6.1.4.1.674.10895.3.1.13.2.1.2 |
| This is defined as ifIndex in the IF-MIB. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| prioIpPrecValue |
1.3.6.1.4.1.674.10895.3.1.13.2.1.3 |
| Precedence value for this entry. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..7 |
|
| prioIpPrecCos |
1.3.6.1.4.1.674.10895.3.1.13.2.1.4 |
| Class of service for this entry. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
0..7 |
|
| prioIpPrecRestoreDefault |
1.3.6.1.4.1.674.10895.3.1.13.3 |
| This object is to restore IP Precedence
settings of a port to default.
To do this, write it to the value of ifIndex
defined by the ifIndex in the IF-MIB.
When read, this object always returns 0. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| prioIpDscpTable |
1.3.6.1.4.1.674.10895.3.1.13.4 |
| Table for IP DSCP priority mapping. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
PrioIpDscpEntry |
|
| prioIpDscpEntry |
1.3.6.1.4.1.674.10895.3.1.13.4.1 |
| Entry for IP DSCP priority mapping. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
PrioIpDscpEntry |
|
|
| prioIpDscpPort |
1.3.6.1.4.1.674.10895.3.1.13.4.1.1 |
| This is defined as ifIndex in the IF-MIB. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| prioIpDscpValue |
1.3.6.1.4.1.674.10895.3.1.13.4.1.2 |
| DSCP value for this entry. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..63 |
|
| prioIpDscpCos |
1.3.6.1.4.1.674.10895.3.1.13.4.1.3 |
| Class of service for this entry. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
0..7 |
|
| prioIpDscpRestoreDefault |
1.3.6.1.4.1.674.10895.3.1.13.5 |
| This object is to restore IP DSCP
settings of a port to default.
To do this, write it to the value of ifIndex
defined by the ifIndex in the IF-MIB.
When read, this object always returns 0. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| prioIpPortEnableStatus |
1.3.6.1.4.1.674.10895.3.1.13.6 |
| Whether IP Port priority look-up is enabled. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| prioIpPortTable |
1.3.6.1.4.1.674.10895.3.1.13.7 |
| Table for IP port priority mapping. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
PrioIpPortEntry |
|
| prioIpPortEntry |
1.3.6.1.4.1.674.10895.3.1.13.7.1 |
| Entry for IP port priority mapping. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
PrioIpPortEntry |
|
|
| prioIpPortPhysPort |
1.3.6.1.4.1.674.10895.3.1.13.7.1.1 |
| This is defined as ifIndex in the IF-MIB. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| prioIpPortValue |
1.3.6.1.4.1.674.10895.3.1.13.7.1.2 |
| IP port for this value. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
1..65535 |
|
| prioIpPortCos |
1.3.6.1.4.1.674.10895.3.1.13.7.1.3 |
| Class of service for this entry. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
0..7 |
|
| prioIpPortStatus |
1.3.6.1.4.1.674.10895.3.1.13.7.1.4 |
| Writing this to valid(1) creates an entry.
Writing this to invalid(2) destroys an entry. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
valid(1), invalid(2) |
|
| prioCopy |
1.3.6.1.4.1.674.10895.3.1.13.8 |
| OBJECT IDENTIFIER |
|
|
|
| prioCopyIpPrec |
1.3.6.1.4.1.674.10895.3.1.13.8.1 |
| Action to copy IP Precedence settings from
a source port to many destination ports.
The first four octets represent an integer for
the source port, in high-to-low (big-endian) order.
Starting from the 5th octet is destination port list
in a form described by PortList in the Q-BRIDGE-MIB.
Writing this object will perform copy.
Reading this object will always get a zero-length
octet string. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
OCTET STRING |
|
|
| prioCopyIpDscp |
1.3.6.1.4.1.674.10895.3.1.13.8.2 |
| Action to copy IP DSCP settings from
a source port to many destination ports.
The first four octets represent an integer for
the source port, in high-to-low (big-endian) order.
Starting from the 5th octet is destination port list
in a form described by PortList in the Q-BRIDGE-MIB.
Writing this object will perform copy.
Reading this object will always get a zero-length
octet string. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
OCTET STRING |
|
|
| prioCopyIpPort |
1.3.6.1.4.1.674.10895.3.1.13.8.3 |
| Action to copy IP Port settings from
a source port to many destination ports.
The first four octets represent an integer for
the source port, in high-to-low (big-endian) order.
Starting from the 5th octet is destination port list
in a form described by PortList in the Q-BRIDGE-MIB.
Writing this object will perform copy.
Reading this object will always get a zero-length
octet string. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
OCTET STRING |
|
|
| prioWrrTable |
1.3.6.1.4.1.674.10895.3.1.13.9 |
| Table for weighted round robin (WRR). |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
PrioWrrEntry |
|
| prioWrrEntry |
1.3.6.1.4.1.674.10895.3.1.13.9.1 |
| Entry for weighted round robin (WRR). |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
PrioWrrEntry |
|
|
| prioWrrTrafficClass |
1.3.6.1.4.1.674.10895.3.1.13.9.1.1 |
| Traffic class for this entry, as defined in
dot1dTrafficClass in the Q-BRIDGE-MIB. The actual
maximum depends on the hardware, and is
equal to dot1dPortNumTrafficClasses-1. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
0..7 |
|
| prioWrrWeight |
1.3.6.1.4.1.674.10895.3.1.13.9.1.2 |
| Weight for this entry. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..255 |
|
| trapDestTable |
1.3.6.1.4.1.674.10895.3.1.14.1 |
| A list of trap destination entries. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
TrapDestEntry |
|
| trapDestEntry |
1.3.6.1.4.1.674.10895.3.1.14.1.1 |
| This entry includes a destination IP address to which to send
traps for this community. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
TrapDestEntry |
|
|
| trapDestAddress |
1.3.6.1.4.1.674.10895.3.1.14.1.1.1 |
| The address to send traps. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
IpAddress |
|
|
| trapDestStatus |
1.3.6.1.4.1.674.10895.3.1.14.1.1.3 |
| Writing this to valid(1) creates an entry.
Writing this to invalid(2) destroys an entry. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
valid(1), invalid(2) |
|
| trapDestVersion |
1.3.6.1.4.1.674.10895.3.1.14.1.1.4 |
| This variables represent the version of the Trap we wish to send to trap Receiver,
if the value is 1, mean we wish to send Version 1 trap, if the value is 2,
mean we wish to send version 2 trap. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
version1(1), version2(2) |
|
| radiusMgt |
1.3.6.1.4.1.674.10895.3.1.17.4 |
| OBJECT IDENTIFIER |
|
|
|
| tacacsMgt |
1.3.6.1.4.1.674.10895.3.1.17.5 |
| OBJECT IDENTIFIER |
|
|
|
| sshMgt |
1.3.6.1.4.1.674.10895.3.1.17.6 |
| OBJECT IDENTIFIER |
|
|
|
| portSecPortTable |
1.3.6.1.4.1.674.10895.3.1.17.2.1 |
| The Port Security(MAC bindind) Table |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
PortSecPortEntry |
|
| portSecPortEntry |
1.3.6.1.4.1.674.10895.3.1.17.2.1.1 |
| The entry of portSecPortTable |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
PortSecPortEntry |
|
|
| portSecPortIndex |
1.3.6.1.4.1.674.10895.3.1.17.2.1.1.1 |
| The port and the trunk (excluding trunk members) interface of
the portTable. The interface identified by a particular value
of this index is the same interface as identified by the same
value of ifIndex in the IF-MIB. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| portSecPortStatus |
1.3.6.1.4.1.674.10895.3.1.17.2.1.1.2 |
| Set enabled(1) to enable port security and set disabled(2) to
disable port security. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
EnabledStatus |
|
|
| portSecAction |
1.3.6.1.4.1.674.10895.3.1.17.2.1.1.3 |
| The corresponding actions that will take place when a
port is under intruded, when this variable is set to
none(1), no action will perform, when this variable is
set to trap(2), a swPortSecurityTrap trap will send,
when this variable is set to shutdown(3), the port will
shutdown, when this variable is set to
trapAndShutdown(4), a swPortSecurityTrap will send
and the port will shutdown. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
none(1), trap(2), shutdown(3), trapAndShutdown(4) |
|
| radiusServerPortNumber |
1.3.6.1.4.1.674.10895.3.1.17.4.2 |
| IP port number of RADIUS server. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..65535 |
|
| radiusServerKey |
1.3.6.1.4.1.674.10895.3.1.17.4.3 |
| Key for RADIUS. This variable can only be written.
When this variable is read, it always returns a
zero-length string. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
|
|
| radiusServerRetransmit |
1.3.6.1.4.1.674.10895.3.1.17.4.4 |
| Maximum number of retransmissions for RADIUS. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..30 |
|
| radiusServerTimeout |
1.3.6.1.4.1.674.10895.3.1.17.4.5 |
| Timeout for RADIUS. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..65535 |
|
| sshServerStatus |
1.3.6.1.4.1.674.10895.3.1.17.6.1 |
| The status of Secure Shell Server, set this value
to 1 to enable SSH server, set this value to 2 to
disable the SSH server. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
EnabledStatus |
|
|
| sshTimeout |
1.3.6.1.4.1.674.10895.3.1.17.6.4 |
| The time interval that the router waits for the SSH
client to respond. The range is 1-120. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..120 |
|
| sshAuthRetries |
1.3.6.1.4.1.674.10895.3.1.17.6.5 |
| The number of attempts after which the interface is reset.
The range is 1-5. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
1..5 |
|
| sshConnInfoTable |
1.3.6.1.4.1.674.10895.3.1.17.6.6 |
| The table for Secure Shell Connection. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
SshConnInfoEntry |
|
| sshConnInfoEntry |
1.3.6.1.4.1.674.10895.3.1.17.6.6.1 |
| The conceptual row for sshConnInfoTable. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SshConnInfoEntry |
|
|
| sshConnID |
1.3.6.1.4.1.674.10895.3.1.17.6.6.1.1 |
| The connection ID of the Secure Shell Connection. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| sshConnEncryptionType |
1.3.6.1.4.1.674.10895.3.1.17.6.6.1.4 |
| The encryption type of the SSH. none(1) mean no encrytion
, des(2) mean using DES encrytion, tribeDes mean using
3DES encrytion. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
none(1), des(2), tribeDes(3) |
|
| sshConnStatus |
1.3.6.1.4.1.674.10895.3.1.17.6.6.1.5 |
| The SSH connection State. negotiationStart(1) mean the
SSH is in its negotiation start state, authenticationStart(2)
mean the SSH is in authentication start state, sessionStart(3)
mean the SSH is in session start State. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
negotiationStart(1), authenticationStart(2), sessionStart(3) |
|
| sshConnUserName |
1.3.6.1.4.1.674.10895.3.1.17.6.6.1.6 |
| The user name of the connection. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
OCTET STRING |
|
|
| sshDisconnect |
1.3.6.1.4.1.674.10895.3.1.17.6.6.1.7 |
| Set the variables to disconnect to disconnect the connection,
when read, this variables always return noDisconnect(1). |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
noDisconnect(1), disconnect(2) |
|
| sysLogStatus |
1.3.6.1.4.1.674.10895.3.1.19.1 |
| Whether system log is enabled. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| sysLogHistoryFlashLevel |
1.3.6.1.4.1.674.10895.3.1.19.2 |
| Severity level for logging to flash. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
0..7 |
|
| sysLogHistoryRamLevel |
1.3.6.1.4.1.674.10895.3.1.19.3 |
| Severity level for logging to RAM. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
0..7 |
|
| remoteLogMgt |
1.3.6.1.4.1.674.10895.3.1.19.6 |
| OBJECT IDENTIFIER |
|
|
|
| remoteLogStatus |
1.3.6.1.4.1.674.10895.3.1.19.6.1 |
| Whether the remote log system is enabled. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
EnabledStatus |
|
|
| remoteLogLevel |
1.3.6.1.4.1.674.10895.3.1.19.6.2 |
| Severity level for remote log. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..7 |
|
| remoteLogFacilityType |
1.3.6.1.4.1.674.10895.3.1.19.6.3 |
| The FacilityType for remote log. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
localUse0(16), localUse1(17), localUse2(18), localUse3(19), localUse4(20), localUse5(21), localUse6(22), localUse7(23) |
|
| remoteLogServerEntry |
1.3.6.1.4.1.674.10895.3.1.19.6.4.1 |
| A conceptually row for remoteLogServerTable. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
RemoteLogServerEntry |
|
|
| remoteLogServerIp |
1.3.6.1.4.1.674.10895.3.1.19.6.4.1.1 |
| The IP address of the remote log Server. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
IpAddress |
|
|
| remoteLogServerStatus |
1.3.6.1.4.1.674.10895.3.1.19.6.4.1.2 |
| Setting this to valid(1) creates an entry.
Setting this to invalid(2) destroys an entry. |
| Status: current |
Access: read-create |
| OBJECT-TYPE |
|
|
|
| |
ValidStatus |
|
|
| consoleMgt |
1.3.6.1.4.1.674.10895.3.1.20.1 |
| OBJECT IDENTIFIER |
|
|
|
| telnetMgt |
1.3.6.1.4.1.674.10895.3.1.20.2 |
| OBJECT IDENTIFIER |
|
|
|
| consoleDataBits |
1.3.6.1.4.1.674.10895.3.1.20.1.1 |
| Number of data bits. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
databits7(1), databits8(2) |
|
| consoleParity |
1.3.6.1.4.1.674.10895.3.1.20.1.2 |
| Define the generation of a parity bit. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
partyNone(1), partyEven(2), partyOdd(3) |
|
| consoleBaudRate |
1.3.6.1.4.1.674.10895.3.1.20.1.3 |
| Baud rate. Valid values are 115200, 57600, 38400,
19200, and 9600. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
baudRate9600(1), baudRate19200(2), baudRate38400(3), baudRate57600(4), baudRate115200(5) |
|
| consoleStopBits |
1.3.6.1.4.1.674.10895.3.1.20.1.4 |
| The stop Bits of the console, valid value is stopbits1(1) or stopbits2(2) |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
stopbits1(1), stopbits2(2) |
|
| consoleExecTimeout |
1.3.6.1.4.1.674.10895.3.1.20.1.5 |
| In serial console, use the consoleExecTimeout
variables to set the interval that the EXEC command
interpreter waits until user input is detected,
set the value to 0 to disable it. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
0..65535 |
|
| consolePasswordThreshold |
1.3.6.1.4.1.674.10895.3.1.20.1.6 |
| In serial console, use the consolePasswordThreshold variabes to
set the password intrusion threshold, which limits the number of
failed logon attempts allowed. Set it value to 0 to disable it. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
0..120 |
|
| consoleSilentTime |
1.3.6.1.4.1.674.10895.3.1.20.1.7 |
| In Console, Use the consoleSilentTime variable to set the amount
of time the management console is inaccessible after the number
of unsuccessful logon attempts exceeds the threshold set by the
password-thresh command. Set it to 0 to disable it. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
0..65535 |
|
| telnetExecTimeout |
1.3.6.1.4.1.674.10895.3.1.20.2.1 |
| In a telnet session, to set the interval that the EXEC command interpreter
waits until user input is detected, use the telnetExecTimeout
variables. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
0..65535 |
|
| telnetPasswordThreshold |
1.3.6.1.4.1.674.10895.3.1.20.2.2 |
| In a telnet session, use the consolePasswordThreshold variabes to
set the password intrusion threshold, which limits the number of
failed logon attempts allowed. Set it value to 0 to disable it. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
0..120 |
|
| swPowerStatusChangeTrap |
1.3.6.1.4.1.674.10895.3.2.1.0.1 |
| This trap is sent when the power status of
an individual power changes. |
| Status: current |
Access: read-write |
| NOTIFICATION-TYPE |
|
|
|
| swPortSecurityTrap |
1.3.6.1.4.1.674.10895.3.2.1.0.36 |
| This trap is sent when the port is being intruded. This trap
will only be sent when the portSecActionTrap is enabled. |
| Status: current |
Access: read-write |
| NOTIFICATION-TYPE |
|
|
|