PW-CEM-MIB

File: PW-CEM-MIB.mib (64380 bytes)

Imported modules

SNMPv2-SMI	SNMPv2-TC	IF-MIB
COSINE-ORION-MIB	PerfHist-TC-MIB	PW-MIB

Imported symbols

MODULE-IDENTITY	OBJECT-TYPE	NOTIFICATION-TYPE
experimental	Integer32	Counter32
Unsigned32	Counter64	TEXTUAL-CONVENTION
TruthValue	RowStatus	StorageType
TimeStamp	InterfaceIndex	InterfaceIndexOrZero
PwVcIndex	PerfCurrentCount	PerfIntervalCount
pwVcIndex	pwVcInstance	pwVcOperStatus

Defined Types

PwVcCemConfIndex
Index into the pwVcCemConfTable. Removed trap OID declarations
TEXTUAL-CONVENTION
	Unsigned32

PwVcCemEntry
SEQUENCE
	pwVcCemSonetPathIfIndex	InterfaceIndexOrZero
	pwVcCemConfIndex	PwVcCemConfIndex
	pwVcCemPerfDbaInPacketsHC	Counter64
	pwVcCemPerfDbaOutPacketsHC	Counter64
	pwVcCemPerfDbaInPackets	Counter32
	pwVcCemPerfDbaOutPackets	Counter32
	pwVcCemPerfInNegPtrAdjustHC	Counter32
	pwVcCemPerfInPosPtrAdjustHC	Counter32
	pwVcCemPerfInPtrAdjustSecs	Counter32
	pwVcCemPerfOutNegPtrAdjustHC	Counter32
	pwVcCemPerfOutPosPtrAdjustHC	Counter32
	pwVcCemPerfOutPtrAdjustSecs	Counter32
	pwVcCemPerfAbsPtrAdjust	Integer32
	pwVcCemPerfCorrectableHdrErrors	Counter32
	pwVcCemPerfUncorrectableHdrErrors	Counter32
	pwVcCemPerfMissingPkts	Counter32
	pwVcCemPerfPktsOoseq	Counter32
	pwVcCemPerfPktsOoseqDropped	Counter32
	pwVcCemPerfJtrBfrUnderruns	Counter32
	pwVcCemPerfJtrBfrOverruns	Counter32
	pwVcCemPerfPktsBadLength	Counter32
	pwVcCemPerfESs	Counter32
	pwVcCemPerfSESs	Counter32
	pwVcCemPerfUASs	Counter32
	pwVcCemPerfLastDefectsAtFailure	BITS
	pwVcCemPerfLastFailureTimeStamp	TimeStamp
	pwVcCemPerfDiscontinuityTime	TimeStamp

PwVcCemConfEntry
SEQUENCE
	pwVcCemConfTableIndex	PwVcCemConfIndex
	pwVcCemConfigError	BITS
	pwVcCemConfMaxPktLength	Unsigned32
	pwVcCemConfMinPktLength	Unsigned32
	pwVcCemConfCemOptions	Unsigned32
	pwVcCemConfPktResequence	TruthValue
	pwVcCemConfEnableDBA	BITS
	pwVcCemConfJtrBfrDepth	Unsigned32
	pwVcCemConfConsecPktsInsync	Unsigned32
	pwVcCemConfConsecMissingOutSync	Unsigned32
	pwVcCemConfErrorAction	INTEGER
	pwVcCemConfUserErrorAction	Unsigned32
	pwVcCemConfSesToUas	Unsigned32
	pwVcCemConfUasAction	INTEGER
	pwVcCemConfUserUasAction	Unsigned32
	pwVcCemConfApsCriteria	BITS
	pwVcCemConfRowStatus	RowStatus
	pwVcCemConfStorageType	StorageType

PwVcCemPerfCurrentEntry
SEQUENCE
	pwVcCemPerfCurrentDbaInPacketsHC	Counter64
	pwVcCemPerfCurrentDbaOutPacketsHC	Counter64
	pwVcCemPerfCurrentDbaInPackets	Counter32
	pwVcCemPerfCurrentDbaOutPackets	Counter32
	pwVcCemPerfCurrentInNegPtrAdjustHC	Counter32
	pwVcCemPerfCurrentInPosPtrAdjustHC	Counter32
	pwVcCemPerfCurrentInPtrAdjustSecs	Counter32
	pwVcCemPerfCurrentOutNegPtrAdjustHC	Counter32
	pwVcCemPerfCurrentOutPosPtrAdjustHC	Counter32
	pwVcCemPerfCurrentOutPtrAdjustSecs	Counter32
	pwVcCemPerfCurrentAbsPtrAdjust	Integer32
	pwVcCemPerfCurrentCrctHdrErrors	Counter32
	pwVcCemPerfCurrentUncrctHdrErrors	Counter32
	pwVcCemPerfCurrentMissingPkts	Counter32
	pwVcCemPerfCurrentPktsOoseq	Counter32
	pwVcCemPerfCurrentPktsOoseqDropped	Counter32
	pwVcCemPerfCurrentJtrBfrUnderruns	Counter32
	pwVcCemPerfCurrentJtrBfrOverruns	Counter32
	pwVcCemPerfCurrentPktsBadLength	Counter32
	pwVcCemPerfCurrentESs	PerfCurrentCount
	pwVcCemPerfCurrentSESs	PerfCurrentCount
	pwVcCemPerfCurrentUASs	PerfCurrentCount

PwVcCemPerfIntervalEntry
SEQUENCE
	pwVcCemPerfIntervalNumber	Unsigned32
	pwVcCemPerfIntervalValidData	TruthValue
	pwVcCemPerfIntervalReset	INTEGER
	pwVcCemPerfIntervalDbaInPacketsHC	Counter64
	pwVcCemPerfIntervalDbaOutPacketsHC	Counter64
	pwVcCemPerfIntervalDbaInPackets	Counter32
	pwVcCemPerfIntervalDbaOutPackets	Counter32
	pwVcCemPerfIntervalInNegPtrAdjustHC	Counter32
	pwVcCemPerfIntervalInPosPtrAdjustHC	Counter32
	pwVcCemPerfIntervalInPtrAdjustSecs	Counter32
	pwVcCemPerfIntervalOutNegPtrAdjustHC	Counter32
	pwVcCemPerfIntervalOutPosPtrAdjustHC	Counter32
	pwVcCemPerfIntervalOutPtrAdjustSecs	Counter32
	pwVcCemPerfIntervalAbsPtrAdjust	Integer32
	pwVcCemPerfIntervalCrctHdrErrors	Counter32
	pwVcCemPerfIntervalUncrctHdrErrors	Counter32
	pwVcCemPerfIntervalMissingPkts	Counter32
	pwVcCemPerfIntervalPktsOoseq	Counter32
	pwVcCemPerfIntervalPktsOoseqDropped	Counter32
	pwVcCemPerfIntervalJtrBfrUnderruns	Counter32
	pwVcCemPerfIntervalJtrBfrOverruns	Counter32
	pwVcCemPerfIntervalPktsBadLength	Counter32
	pwVcCemPerfIntervalESs	PerfIntervalCount
	pwVcCemPerfIntervalSESs	PerfIntervalCount
	pwVcCemPerfIntervalUASs	PerfIntervalCount

PwVcCemSonetPathExtEntry
SEQUENCE
	pwVcCemSonetExtPathIfIndex	InterfaceIndex
	pwVcCemSonetPathExtVcIndex	PwVcIndex
	pwVcCemSonetPathExtTimeSlot	Unsigned32
	pwVcCemSonetPathExtStorageType	StorageType

Defined Values

pwVcCemMIB		1.3.6.1.3.8888
This MIB contains managed object definitions for Circuit Emulation over MPLS as in: Malis, A., Vogelsang, S., and Martini, L. 'SONET/SDH Circuit Emulation Service Over MPLS (CEM) encapsulation', Internet Draft , July 2001. This MIB reports to the PW-MIB. The PW-MIB contains structures and MIB associations generic to Pseudo-Wire Virtual Circuit (VC) emulation. VC-specific MIBs (such as this) contain config and stats for specific VC types.
MODULE-IDENTITY

pwVcCemNotifications		1.3.6.1.3.8888.0
OBJECT IDENTIFIER

pwVcCemNotifyPrefix		1.3.6.1.3.8888.0.0
OBJECT IDENTIFIER

pwVcCemObjects		1.3.6.1.3.8888.1
OBJECT IDENTIFIER

pwVcCemTable		1.3.6.1.3.8888.1.1
This table contains the index to the entry SONET path table for this CEM VC, the index to the CEM config table, and CEM statistics.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PwVcCemEntry

pwVcCemEntry		1.3.6.1.3.8888.1.1.1
This MIB reports to the PW-MIB. This table is indexed by the same index that was created for the associated entry in the PW VC Table (in the PW-MIB). - The PwVcIndex. - The PwVcInstance. An entry is created in this table by the agent for every entry in the pwVc table with a VcType of 'cem'. This table provides per CEM VC performance information. HC (high capacity) counters are required for some counts due to the high speeds expected with CEM services. A SONET path of width 48 (STS-48c) can rollover non-HC counters in a few minutes. CEM bridges the SONET and packet worlds. In the packet world, counts typically start from the time of service creation - and don't stop. In the SONET world, counts are kept in 15 minute intervals. The CEM-MIB supports both methods. Thestats in the VC CEM table count forever. The 15 minute interval counts are in the tables following this. NOTE: Outbound errors are currently not considered in the CEM-MIB. It is assumed that CEM packets are forwarded as they are generated. i.e., It is assumed that there are no congestion issues at the point of CEM adaptation.
Status: current	Access: not-accessible
OBJECT-TYPE
	PwVcCemEntry

pwVcCemSonetPathIfIndex		1.3.6.1.3.8888.1.1.1.1
This is a unique index within the ifTable. It represents the interface index for the SONET path. A value of zero indicates an interface index that has yet to be configured or has since disappeared. Note: if there are multiple instances of CEM VC, then the pathIfIndex object MUST be identical in each instance.
Status: current	Access: read-write
OBJECT-TYPE
	InterfaceIndexOrZero

pwVcCemConfIndex		1.3.6.1.3.8888.1.1.1.2
Index to CEM configuration table below. It is likely that multiple CEM VCs will share 1 CEM conf table entry.
Status: current	Access: read-write
OBJECT-TYPE
	PwVcCemConfIndex

pwVcCemPerfDbaInPacketsHC		1.3.6.1.3.8888.1.1.1.3
Number of DBA packets received.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

pwVcCemPerfDbaOutPacketsHC		1.3.6.1.3.8888.1.1.1.4
Number of DBA packets sent.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

pwVcCemPerfDbaInPackets		1.3.6.1.3.8888.1.1.1.5
Number of DBA packets received.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfDbaOutPackets		1.3.6.1.3.8888.1.1.1.6
Number of DBA packets sent.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfInNegPtrAdjustHC		1.3.6.1.3.8888.1.1.1.7
Number of negative pointer adjustments sent on the SONET path based on CEM pointer adjustments received.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfInPosPtrAdjustHC		1.3.6.1.3.8888.1.1.1.8
Number of postive pointer adjustments sent on the SONET path based on CEM pointer adjustments received.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfInPtrAdjustSecs		1.3.6.1.3.8888.1.1.1.9
Number of seconds in which a pos or neg pointer adjustment was sent on the SONET path.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfOutNegPtrAdjustHC		1.3.6.1.3.8888.1.1.1.10
Number of negative pointer adjustments seen on the SONET path and encoded onto sent CEM packets.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfOutPosPtrAdjustHC		1.3.6.1.3.8888.1.1.1.11
Number of positive pointer adjustments seen on the SONET path and encoded onto sent CEM packets.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfOutPtrAdjustSecs		1.3.6.1.3.8888.1.1.1.12
Number of seconds in which a pos or neg pointer adjustment was seen on the SONET path.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfAbsPtrAdjust		1.3.6.1.3.8888.1.1.1.13
Absolute Pointer adjustments is relative adjustment drifts between inbound and outbound streams. It is calculated as such : ( InPosPtrAdjust - InNegPtrAdjust) - (OutPosPtrAdjust - OutNegPtrAdjust)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

pwVcCemPerfCorrectableHdrErrors		1.3.6.1.3.8888.1.1.1.14
Number of correctable CEM header errors detected on inbound CEM packets.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfUncorrectableHdrErrors		1.3.6.1.3.8888.1.1.1.15
Number of uncorrectable CEM header errors detected on inbound CEM packets.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfMissingPkts		1.3.6.1.3.8888.1.1.1.16
Number of missing packets (as detected via CEM header sequence number gaps).
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfPktsOoseq		1.3.6.1.3.8888.1.1.1.17
Number of packets detected out of sequence (via CEM header sequence numbers), but were able to be re-sequenced. Note: some implementations may not support this feature (see pwVcCemConfPktResequence).
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfPktsOoseqDropped		1.3.6.1.3.8888.1.1.1.18
Number of packets detected out of sequence (via CEM header sequence numbers), but were unable to be re- sequenced.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfJtrBfrUnderruns		1.3.6.1.3.8888.1.1.1.19
Number of times the jitter buffer transitioned to empty.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfJtrBfrOverruns		1.3.6.1.3.8888.1.1.1.20
Number of packets received while jitter buffer is full.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfPktsBadLength		1.3.6.1.3.8888.1.1.1.21
Number of packets received larger or smaller than pwVcCemConfPktLength.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfESs		1.3.6.1.3.8888.1.1.1.22
The counter associated with the number of Errored Seconds encountered. See future versions of draft-malis-sonet-ces-mpls for definition of ES.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfSESs		1.3.6.1.3.8888.1.1.1.23
The counter associated with the number of Severely Errored Seconds. See future versions of draft-malis-sonet-ces-mpls for definition of SES.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfUASs		1.3.6.1.3.8888.1.1.1.24
The counter associated with the number of UnAvailable Seconds. See pwVcCemConfSesToUAS. NOTE: When first entering the UAS state, the number of SesToUas is added to this object, then as each additional UAS occurs, this object increments by one.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfLastDefectsAtFailure		1.3.6.1.3.8888.1.1.1.25
The state of defects when CEM VC last entered the a 'failure' state. Since more than one defect can contributed to a CEM VC failure, all are shown here. Note: currently there is no hierarchy of CEM defects. Note: the algorithm used to capture these defects when entering failure state is implementation specific. Note: definition of 'CEM failure' is for further study. One possible definition: in LOPS state for 2.5 seconds. A 'CEM failure' may be also be determined (via software) as a result of trend analysis (e.g., missing packet ratio over time).
Status: current	Access: read-only
OBJECT-TYPE
	BITS	uncrctHdr(0), missingPkt(1), ooSeqDropped(2), jtrBfrUnder(3), jtrBfrOver(4), pktBadLength(5), lops(6)

pwVcCemPerfLastFailureTimeStamp		1.3.6.1.3.8888.1.1.1.26
The value of sysUpTime on the most recent occasion at which the CEM enterd the 'failure' state.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

pwVcCemPerfDiscontinuityTime		1.3.6.1.3.8888.1.1.1.27
The value of sysUpTime on the most recent occasion at which any one or more of this segment's Counter32 or Counter64 suffered a discontinuity. If no such discontinuities have occurred since the last re- initialization of the local management subsystem, then this object contains a zero value.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

pwVcCemConfIndexNext		1.3.6.1.3.8888.1.2
This object contains an appropriate value to be used for pwVcCemConfIndex when creating entries in the pwVcCemConfTable. The value 0 indicates that no unassigned entries are available. To obtain the value of pwVcCemConfIndex for a new entry in the pwVcCemConfTable, the manager issues a management protocol retrieval operation to obtain the current value of pwVcCemConfIndex. After each retrieval operation, the agent should modify the value to reflect the next unassigned index. After a manager retrieves a value the agent will determine through its local policy when this index value will be made available for reuse.
Status: current	Access: read-only
OBJECT-TYPE
	PwVcCemConfIndex

pwVcCemConfTable		1.3.6.1.3.8888.1.3
This table contains a set of parameters that may be referenced by 1 or more CEM VCs by pwVcCemTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PwVcCemConfEntry

pwVcCemConfEntry		1.3.6.1.3.8888.1.3.1
These parameters define the characteristics of a CEM VC. They are grouped here to ease NMS burden. Once an entry is created here it may be re-used by many VCs.
Status: current	Access: not-accessible
OBJECT-TYPE
	PwVcCemConfEntry

pwVcCemConfTableIndex		1.3.6.1.3.8888.1.3.1.1
Primary index to this table
Status: current	Access: not-accessible
OBJECT-TYPE
	PwVcCemConfIndex

pwVcCemConfigError		1.3.6.1.3.8888.1.3.1.2
Various configurations errors. Illegal settings within the pwVcCemConf table.
Status: current	Access: read-only
OBJECT-TYPE
	BITS	dba(0), resequencing(1), lopsPktCount(2), pktLength(3), jtrBfrDepth(4), cemOptions(5)

pwVcCemConfMaxPktLength		1.3.6.1.3.8888.1.3.1.3
This is the maximum CEM packet length in number of bytes (including CEM header and payload). It is fixed and applies to inbound and outbound packets carrying user payload. Although there is no control over inbound packets, those of illegal length are discarded and accounted for (see pwVcCemPerfPktsBadLength.) Note: DBA packets have their own (shorter) length and are not effected by this setting. If there were to be CEM payload compression, compressed packets would have their own (shorter) length not effected by this setting. Used by signaling (LDP) to fill in the 'Virtual Circuit FEC element' and the CEM interface parameters therein.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

pwVcCemConfMinPktLength		1.3.6.1.3.8888.1.3.1.4
This is the minimum CEM packet length in number of bytes (including CEM header and payload). It applies to CEM's bandwidth-savings packets. Currently DBA is the only bandwidth-savings packet type (in the future, CEM may support compression). Minimum packet length is necessary in some systems or networks. Setting Zero here indicates that there is no minimum packet restriction. If non-zero, then packets too small are be discarded and accounted for (see pwVcCemPerfPktsBadLength.) Used by signaling (LDP) to fill in the 'Virtual Circuit FEC element' and the CEM interface parameters therein.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

pwVcCemConfCemOptions		1.3.6.1.3.8888.1.3.1.5
Used by signaling (LDP) to fill in the 'Virtual Circuit FEC element' and the CEM interface parameters therein. CEM options are formatted into bit fields within a 16-bit word. Such fields will define CEM-DBA, STS-n starting time slot, etc.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

pwVcCemConfPktResequence		1.3.6.1.3.8888.1.3.1.6
If set True: as inbound packets are queued in the jitter buffer, out of order packets are re-sequenced. The maximum sequence number differential (i.e., the range in which resequencing can occur) is dependant on the depth of the jitter buffer. See pwVcCemConfJtrBfrDepth. NOTE: Some implementations may not support this feature. If set True, then error code is set in pwVcCemConfigError. NOTE: Some implementations may always have this feature on. If set False, then error code is set in pwVcCemConfigError.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

pwVcCemConfEnableDBA		0.1.3.6.1.3.8888.1.3.1.7
Any bits set here MUST enable the DBA (dynamic bandwidth allocation) feature for the specified condition. Setting allOnesOnAis will cause CEM packet payload suppression when AIS is detected on the associated SONET path. Similarly, allZerosOnUnequipped will cause payload suppression when the SONET path is un-equipped. During these conditions, CEM packets will continue to be sent, but with indicators set in the CEM header instructing the remote to play all ones or zeros onto its SONET path. NOTE: some implementations may not support this feature. If set, then an error code is set in pwVcCemConfigError.
Status: current	Access: read-create
OBJECT-TYPE
	BITS	allOnesOnAis(0), allZerosOnUnequipped(1)

pwVcCemConfJtrBfrDepth		1.3.6.1.3.8888.1.3.1.8
This setting configures the number of packet buffers reserved for this CEM VC. This object essentially sets the maximum amount of time allowed between CEM packets before the jitter buffer empties. This variable should be set based on the SONET path width (speed) and the amount of delay variation expected to be introduced by the network. Like bandwidth, jitter buffers are likely to be a limited resource to be managed.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

pwVcCemConfConsecPktsInsync		1.3.6.1.3.8888.1.3.1.9
Consecutive pkts with sequential sequence numbers required to exit the LOPS state.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

pwVcCemConfConsecMissingOutSync		1.3.6.1.3.8888.1.3.1.10
Consecutive missing pkts required to enter the LOPS state.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

pwVcCemConfErrorAction		1.3.6.1.3.8888.1.3.1.11
These are the actions to take when inbound packets are missing due to gap in sequence numbers (uncorrectable via available re-sequencing), jitter buffer underruns, or packets with bad CEM headers. These patterns are sent (played) on the SONET path. These settings are used for immediate errors and (unless the pwVcCemConfUasAction is 'errorAction') are not in effect once the CEM VC is in UAS state. For userValue see pwVcCemConfUserErrorAction.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	playAllOnes(1), userValue(2)

pwVcCemConfUserErrorAction		1.3.6.1.3.8888.1.3.1.12
Used when userValue selected above. This byte value is sent on every byte in every SPE.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..255

pwVcCemConfSesToUas		1.3.6.1.3.8888.1.3.1.13
Number of consecutive SESs before declaring VC in UAS state (and at which point pwVcCemPerfUASs starts counting). The SesToUas default value is 10 seconds. NOTE: 10 consecutive non-SESs cause the VC to exit the UAS state. See pwVcCemPerfSESs and pwVcCemPerfUASs.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

pwVcCemConfUasAction		1.3.6.1.3.8888.1.3.1.14
These are the actions to take once the CEM VC has been declared in UAS state (as observed in pwVcCemPerfDefects) and there are missing packets (as described in the pwVcCemConfErrorAction object, above). These patterns are sent (played) on the SONET path. If 'errorAction' is selected, then the pwVcCemConfErrorAction settings stay in effect even after the CEM VC is in UAS. For userValue see pwVcCemConfUserUasAction.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	errorAction(1), playAllOnes(2), userValue(3)

pwVcCemConfUserUasAction		1.3.6.1.3.8888.1.3.1.15
Used when userValue selected above. This byte value is sent on every byte in every SPE.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..255

pwVcCemConfApsCriteria		6.1.3.6.1.3.8888.1.3.1.16
Bits set here represent defects used as inputs into APS mechanisms (see PW-MIB). NOTE: these indications are as set within pwVcCemPerfDefects. Note: for APS applications requiring fast response, the 'lops' trigger option is recommended. LOPS can be generated within milliseconds, while UAS is multiple seconds.
Status: current	Access: read-create
OBJECT-TYPE
	BITS	lops(0), es(1), ses(2), uas(3)

pwVcCemConfRowStatus		1.3.6.1.3.8888.1.3.1.17
For creating, modifying, and deleting this row.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

pwVcCemConfStorageType		1.3.6.1.3.8888.1.3.1.18
This variable indicates the storage type for this object.
Status: current	Access: read-create
OBJECT-TYPE
	StorageType

pwVcCemPerfCurrentTable		1.3.6.1.3.8888.1.4
This table provides per CEM VC performance information much like the pwVcCemPerfTable above. However, these counts represent the current 15 minute interval only. NOTE: Counter64 objects are used here, Counter32 is too small for OC-768 CEM VCs.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PwVcCemPerfCurrentEntry

pwVcCemPerfCurrentEntry		1.3.6.1.3.8888.1.4.1
An entry in this table is created by the agent for every pwVcCemConf entry. It is an extension to the pwVcCemConf table. After 15 minutes, the contents of this table entry are copied to a new entry in the pwVcCemPerfInterval table and the counts in this entry are reset to zero.
Status: current	Access: not-accessible
OBJECT-TYPE
	PwVcCemPerfCurrentEntry

pwVcCemPerfCurrentDbaInPacketsHC		1.3.6.1.3.8888.1.4.1.1
Number of DBA packets received.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

pwVcCemPerfCurrentDbaOutPacketsHC		1.3.6.1.3.8888.1.4.1.2
Number of DBA packets sent.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

pwVcCemPerfCurrentDbaInPackets		1.3.6.1.3.8888.1.4.1.3
Number of DBA packets received.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfCurrentDbaOutPackets		1.3.6.1.3.8888.1.4.1.4
Number of DBA packets sent.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfCurrentInNegPtrAdjustHC		1.3.6.1.3.8888.1.4.1.5
Number of negative pointer adjustments sent on the SONET path based on CEM pointer adjustments received.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfCurrentInPosPtrAdjustHC		1.3.6.1.3.8888.1.4.1.6
Number of postive pointer adjustments sent on the SONET path based on CEM pointer adjustments received.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfCurrentInPtrAdjustSecs		1.3.6.1.3.8888.1.4.1.7
Number of seconds in which a pos or neg pointer adjustment was sent on the SONET path.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfCurrentOutNegPtrAdjustHC		1.3.6.1.3.8888.1.4.1.8
Number of negative pointer adjustments seen on the SONET path and encoded onto sent CEM packets.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfCurrentOutPosPtrAdjustHC		1.3.6.1.3.8888.1.4.1.9
Number of positive pointer adjustments seen on the SONET path and encoded onto sent CEM packets.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfCurrentOutPtrAdjustSecs		1.3.6.1.3.8888.1.4.1.10
Number of seconds in which a pos or neg pointer adjustment was seen on the SONET path.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfCurrentAbsPtrAdjust		1.3.6.1.3.8888.1.4.1.11
Absolute Pointer adjustments is relative adjustment drifts between inbound and outbound streams. It is calculated as such : ( InPosPtrAdjust - InNegPtrAdjust) - (OutPosPtrAdjust - OutNegPtrAdjust)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

pwVcCemPerfCurrentCrctHdrErrors		1.3.6.1.3.8888.1.4.1.12
Number of correctable CEM header errors detected on inbound CEM packets.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfCurrentUncrctHdrErrors		1.3.6.1.3.8888.1.4.1.13
Number of uncorrectable CEM header errors detected on inbound CEM packets.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfCurrentMissingPkts		1.3.6.1.3.8888.1.4.1.14
Number of missing packets (as detected via CEM header sequence number gaps).
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfCurrentPktsOoseq		1.3.6.1.3.8888.1.4.1.15
Number of packets detected out of sequence (via CEM header sequence numbers), but were able to be re-sequenced. Note: some implementations may not support this feature (see pwVcCemConfPktResequence).
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfCurrentPktsOoseqDropped		1.3.6.1.3.8888.1.4.1.16
Number of packets detected out of sequence (via CEM header sequence numbers), but were unable to be re- sequenced.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfCurrentJtrBfrUnderruns		1.3.6.1.3.8888.1.4.1.17
Number of times the jitter buffer transitioned to empty.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfCurrentJtrBfrOverruns		1.3.6.1.3.8888.1.4.1.18
Number of packets received while jitter buffer is full.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfCurrentPktsBadLength		1.3.6.1.3.8888.1.4.1.19
Number of non-bandwidth-saving packets received larger or smaller than pwVcCemConfMaxPktLength. Plus number of bandwidth-saving packets (like DBA) that are smaller than pwVcCemConfMinPktLength.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfCurrentESs		1.3.6.1.3.8888.1.4.1.20
The counter associated with the number of Errored Seconds encountered.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCurrentCount

pwVcCemPerfCurrentSESs		1.3.6.1.3.8888.1.4.1.21
The counter associated with the number of Severely Errored Seconds encountered.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCurrentCount

pwVcCemPerfCurrentUASs		1.3.6.1.3.8888.1.4.1.22
The counter associated with the number of Unavailable Seconds encountered.
Status: current	Access: read-only
OBJECT-TYPE
	PerfCurrentCount

pwVcCemPerfIntervalTable		1.3.6.1.3.8888.1.5
This table provides per CEM VC performance information much like the pwVcCemPerfCurrentTable above. However, these counts represent historical 15 minute intervals. Typically, this table will have a maximum of 96 entries for a 24 hour period, but is not limited to this. NOTE: Counter64 objects are used here, Counter32 is too small for OC-768 CEM VCs.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PwVcCemPerfIntervalEntry

pwVcCemPerfIntervalEntry		1.3.6.1.3.8888.1.5.1
An entry in this table is created by the agent for every pwVcCemPerfCurrentEntry that is 15 minutes old. The contents of the Current entry are copied to the new entry here. The Current entry, then resets its counts to zero for the next current 15 minute interval. pwVcCemIndex is found in the pwVcCemConf table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PwVcCemPerfIntervalEntry

pwVcCemPerfIntervalNumber		1.3.6.1.3.8888.1.5.1.1
A number (normally between 1 and 96 to cover a 24 hour period) which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1. The minimum range of N is 1 through 4. The default range is 1 through 32. The maximum value of N is 1 through 96.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

pwVcCemPerfIntervalValidData		1.3.6.1.3.8888.1.5.1.2
This variable indicates if the data for this interval is valid.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

pwVcCemPerfIntervalReset		1.3.6.1.3.8888.1.5.1.3
Used in cases where the user knows that the errors within this interval should not be counted. Writing 'reset' sets all error counts to zero.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	reset(1), normal(2)

pwVcCemPerfIntervalDbaInPacketsHC		1.3.6.1.3.8888.1.5.1.4
Number of DBA packets received.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

pwVcCemPerfIntervalDbaOutPacketsHC		1.3.6.1.3.8888.1.5.1.5
Number of DBA packets sent.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

pwVcCemPerfIntervalDbaInPackets		1.3.6.1.3.8888.1.5.1.6
Number of DBA packets received.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfIntervalDbaOutPackets		1.3.6.1.3.8888.1.5.1.7
Number of DBA packets sent.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfIntervalInNegPtrAdjustHC		1.3.6.1.3.8888.1.5.1.8
Number of negative pointer adjustments sent on the SONET path based on CEM pointer adjustments received.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfIntervalInPosPtrAdjustHC		1.3.6.1.3.8888.1.5.1.9
Number of postive pointer adjustments sent on the SONET path based on CEM pointer adjustments received.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfIntervalInPtrAdjustSecs		1.3.6.1.3.8888.1.5.1.10
Number of seconds in which a pos or neg pointer adjustment was sent on the SONET path.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfIntervalOutNegPtrAdjustHC		1.3.6.1.3.8888.1.5.1.11
Number of negative pointer adjustments seen on the SONET path and encoded onto sent CEM packets.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfIntervalOutPosPtrAdjustHC		1.3.6.1.3.8888.1.5.1.12
Number of positive pointer adjustments seen on the SONET path and encoded onto sent CEM packets.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfIntervalOutPtrAdjustSecs		1.3.6.1.3.8888.1.5.1.13
Number of seconds in which a pos or neg pointer adjustment was seen on the SONET path.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfIntervalAbsPtrAdjust		1.3.6.1.3.8888.1.5.1.14
Absolute Pointer adjustments is relative adjustment drifts between inbound and outbound streams. It is calculated as such : ( InPosPtrAdjust - InNegPtrAdjust) - (OutPosPtrAdjust - OutNegPtrAdjust)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

pwVcCemPerfIntervalCrctHdrErrors		1.3.6.1.3.8888.1.5.1.15
Number of correctable CEM header errors detected on inbound CEM packets.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfIntervalUncrctHdrErrors		1.3.6.1.3.8888.1.5.1.16
Number of uncorrectable CEM header errors detected on inbound CEM packets.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfIntervalMissingPkts		1.3.6.1.3.8888.1.5.1.17
Number of missing packets (as detected via CEM header sequence number gaps).
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfIntervalPktsOoseq		1.3.6.1.3.8888.1.5.1.18
Number of packets detected out of sequence (via CEM header sequence numbers), but were able to be re-sequenced. Note: some implementations mat not support this feature (see pwVcCemConfPktResequence).
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfIntervalPktsOoseqDropped		1.3.6.1.3.8888.1.5.1.19
Number of packets detected out of sequence (via CEM header sequence numbers), but were unable to be re- sequenced.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfIntervalJtrBfrUnderruns		1.3.6.1.3.8888.1.5.1.20
Number of times the jitter buffer transitioned to empty.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfIntervalJtrBfrOverruns		1.3.6.1.3.8888.1.5.1.21
Number of packets received while jitter buffer is full.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfIntervalPktsBadLength		1.3.6.1.3.8888.1.5.1.22
Number of packets received larger or smaller than pwVcCemConfPktLength.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

pwVcCemPerfIntervalESs		1.3.6.1.3.8888.1.5.1.23
The counter associated with the number of Errored Seconds encountered.
Status: current	Access: read-only
OBJECT-TYPE
	PerfIntervalCount

pwVcCemPerfIntervalSESs		1.3.6.1.3.8888.1.5.1.24
The counter associated with the number of Severely Errored Seconds encountered.
Status: current	Access: read-only
OBJECT-TYPE
	PerfIntervalCount

pwVcCemPerfIntervalUASs		1.3.6.1.3.8888.1.5.1.25
The counter associated with the number of Unavailable Seconds encountered.
Status: current	Access: read-only
OBJECT-TYPE
	PerfIntervalCount

pwVcCemSonetPathExtTable		1.3.6.1.3.8888.1.6
This table associates a SONET path with a CEM VC (or a set of CEM VCs) and provides the starting time-slot of the SONET path. It as assumed that the transmit and receive sides of the SONET path have the same starting time-slots. It is also assumed that STSn paths have contiguous time-slots.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PwVcCemSonetPathExtEntry

pwVcCemSonetPathExtEntry		1.3.6.1.3.8888.1.6.1
This table is indexed by the SONET path ifIndex. An entry to this table is created by the agent when an entry (intended for CEM) is created in the sonetPathCurrentTable. Alternatively, an agent may create an entru in this table at the point where a valid ifIndex is written to pwVcCemSonetPathIfIndex in the pwVcCem table. The pwVcCemSonetPathExt table binds a SONET path to a PW CEM VC. A VC index of 0 indicates that the binding has not yet been set.
Status: current	Access: not-accessible
OBJECT-TYPE
	PwVcCemSonetPathExtEntry

pwVcCemSonetExtPathIfIndex		1.3.6.1.3.8888.1.6.1.1
Index for a row in the sonetPathCurrentTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndex

pwVcCemSonetPathExtVcIndex		1.3.6.1.3.8888.1.6.1.2
Index for the conceptual row identifying a VC (or set of VCs) within the generic PW VC table (in PW-MIB) or the local pwVcCemTable.
Status: current	Access: read-write
OBJECT-TYPE
	PwVcIndex

pwVcCemSonetPathExtTimeSlot		1.3.6.1.3.8888.1.6.1.3
Starting time-slot for this SONET path within the SONET line and section. For OC-48, this value could range from 1 to 48. The SONET path width must be taken into consideration here, for example, in an OC-48 an STS-3c could not start at time-slot 47.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	1..192

pwVcCemSonetPathExtStorageType		1.3.6.1.3.8888.1.6.1.4
This variable indicates the storage type for this object.
Status: current	Access: read-write
OBJECT-TYPE
	StorageType

pwVcCemGlobalNotifyEnable		1.3.6.1.3.8888.1.7
If this object is true, then it enables the generation of pwVcCemUp and pwVcCemDown notifications, otherwise these notifications are not emitted. Note: enabling/disabling notifications for individual CEM VCs is for further study.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

pwVcCemUp		1.3.6.1.3.8888.0.0.1
This notification is generated when a CEM VC has exited the 'failure' state.
Status: current	Access: read-write
NOTIFICATION-TYPE

pwVcCemDown		1.3.6.1.3.8888.0.0.2
This notification is generated when a CEM VC has entered the 'failure' state. See description of pwVcCemPerfLastDefectsAtFailure object.
Status: current	Access: read-write
NOTIFICATION-TYPE