PT-RADIOLINK-MIB

File: PT-RADIOLINK-MIB.mib (51428 bytes)

Imported modules

SNMPv2-SMI	SNMPv2-TC	SNMPv2-CONF
INET-ADDRESS-MIB	IF-MIB	PT-MIB

Imported symbols

MODULE-IDENTITY	OBJECT-TYPE	Counter32
Integer32	IpAddress	TEXTUAL-CONVENTION
MODULE-COMPLIANCE	OBJECT-GROUP	InetAddressIPv6
ifEntry	pt

Defined Types

AcmTC
An integer which indicates the ACM.
TEXTUAL-CONVENTION
	INTEGER	acmHalfBpsk(1), acmHalfBpskLight(2), acmHalfBpskStrong(3), acmBpsk(4), acmBpskLight(5), acmBpskStrong(6), acm4Qam(7), acm4QamLight(8), acm4QamStrong(9), acm16Qam(10), acm16QamLight(11), acm16QamStrong(12), acm32Qam(13), acm32QamLight(14), acm32QamStrong(15), acm64Qam(16), acm64QamLight(17), acm64QamStrong(18), acm128Qam(19), acm128QamLight(20), acm128QamStrong(21), acm256Qam(22), acm256QamLight(23), acm256QamStrong(24), acm512Qam(25), acm512QamLight(26), acm512QamStrong(27), acm1024Qam(28), acm1024QamLight(29), acm1024QamStrong(30), acm2048Qam(31), acm2048QamLight(32), acm2048QamStrong(33), acm4096Qam(34), acm4096QamLight(35), acm4096QamStrong(36)

EnableStatusTC
An integer which indicates the enabled status.
TEXTUAL-CONVENTION
	INTEGER	enabled(1), disabled(2), unknown(3)

XpicMimoTC
An integer which indicates the XPIC or MIMO status.
TEXTUAL-CONVENTION
	INTEGER	notAvailable(1), locked(2), unlocked(3), unknown(4)

CtEntry
SEQUENCE
	actualInputPower	OCTET STRING
	actualOutputPower	OCTET STRING
	actualRxAcm	OCTET STRING
	actualTxAcm	OCTET STRING
	ctDistinguishedName	OCTET STRING
	description	OCTET STRING
	carrierId	INTEGER
	ctStatus	INTEGER
	frameId	Integer32
	txFrequency	Integer32
	minTxFrequency	Integer32
	maxTxFrequency	Integer32
	rxFrequency	Integer32
	minRxFrequency	Integer32
	maxRxFrequency	Integer32
	frequencyStepSize	Integer32
	duplexDistance	Integer32
	duplexType	INTEGER
	duplexConfig	EnableStatusTC
	autoFreqSelection	INTEGER
	autoFreqSelectedChannel	Integer32
	autoFreqSelectionStatus	INTEGER
	channelSpacing	INTEGER
	polarization	INTEGER
	txOperStatus	INTEGER
	txAdminStatus	INTEGER
	selectedOutputPowerType	INTEGER
	availableOutputPowerType	INTEGER
	selectedMinOutputPower	Integer32
	selectedMaxOutputPower	Integer32
	availableMinOutputPower	Integer32
	availableMaxOutputPower	Integer32
	referenceSec	INTEGER
	targetInputPowerFarEnd	Integer32
	berAlarmThreshold	INTEGER
	inputPowerAlarmThreshold	Integer32
	plannedAlignmentInputPower	Integer32
	atpcFallback	EnableStatusTC
	atpcFallbackTimer	Integer32
	atpcFallbackOutputPower	Integer32
	xpicStatus	XpicMimoTC
	mimoStatus	XpicMimoTC
	actualSnir	OCTET STRING
	actualXpi	OCTET STRING
	actualSi	OCTET STRING
	actualTxCapacity	Integer32
	licensedCapacity	Integer32
	availableMinCapacity	Integer32
	availableMaxCapacity	Integer32
	selectedMinCapacity	Integer32
	selectedMaxCapacity	Integer32
	wantedLicensedCapacity	Integer32
	availableMinAcm	AcmTC
	availableMaxAcm	AcmTC
	selectedMinAcm	AcmTC
	selectedMaxAcm	AcmTC
	actualRxAcmTC	AcmTC
	actualTxAcmTC	AcmTC
	alignmentMode	EnableStatusTC
	rfLoop	EnableStatusTC

RltEntry
SEQUENCE
	rltDistinguishedName	OCTET STRING
	neIpAddress	IpAddress
	neIpv6Address	InetAddressIPv6
	neName	OCTET STRING
	neType	INTEGER
	id	OCTET STRING
	rltStatus	INTEGER
	mode	INTEGER
	actualTxTotalCapacity	Integer32
	limitedTotalCapacity	Integer32
	protectionStatus	INTEGER
	revertiveWaitToRestore	Integer32
	revertivePreferredTx	INTEGER
	protectionSwitchMode	INTEGER
	fadeNotificationTimer	Integer32
	expectedFarEndId	OCTET STRING
	farEndIdCheck	INTEGER
	cpriMode	INTEGER
	cpriStatus	INTEGER
	manualSwitch	INTEGER
	mlhcOperStatus	INTEGER
	mlhcAdminStatus	INTEGER
	mlhcMplsConfig	INTEGER
	plcOperStatus	INTEGER
	plcAdminStatus	INTEGER

CtG826ContinuousEntry
SEQUENCE
	ctG826TimeElapsed	Counter32
	ctBBE	Counter32
	ctBBER	OCTET STRING
	ctES	Counter32
	ctESR	OCTET STRING
	ctSES	Counter32
	ctSESR	OCTET STRING
	ctBB	OCTET STRING
	ctUAS	Counter32
	ctG826Reset	INTEGER

CtG826Current15mEntry
SEQUENCE
	ctG826Current15mTimeElapsed	Counter32
	ctCurrent15mBBE	Counter32
	ctCurrent15mBBER	OCTET STRING
	ctCurrent15mES	Counter32
	ctCurrent15mESR	OCTET STRING
	ctCurrent15mSES	Counter32
	ctCurrent15mSESR	OCTET STRING
	ctCurrent15mBB	Counter32
	ctCurrent15mUAS	Counter32

CtG826Current24hEntry
SEQUENCE
	ctG826Current24hTimeElapsed	Counter32
	ctCurrent24hBBE	Counter32
	ctCurrent24hBBER	OCTET STRING
	ctCurrent24hES	Counter32
	ctCurrent24hESR	OCTET STRING
	ctCurrent24hSES	Counter32
	ctCurrent24hSESR	OCTET STRING
	ctCurrent24hBB	Counter32
	ctCurrent24hUAS	Counter32

Defined Values

ptRadioLink		6.7
This is the MIB for Radio Link specifics in PT
MODULE-IDENTITY

ptRadioLinkConformance		6.7.2
OBJECT IDENTIFIER

ctPerformance		6.7.4
OBJECT IDENTIFIER

ctTable		6.7.1
A table of CT Table entries.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CtEntry

ctEntry		6.7.1.1
An entry of CT application.
Status: current	Access: not-accessible
OBJECT-TYPE
	CtEntry

actualInputPower		6.7.1.1.1
Actual input power of the CT in dBm
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

actualOutputPower		6.7.1.1.2
Actual output power of the CT in dBm
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

actualRxAcm		6.7.1.1.3
Actual rx modulation and coding
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

actualTxAcm		6.7.1.1.4
Actual tx modulation and coding
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

ctDistinguishedName		6.7.1.1.5
Unique id/name of the carrier termination, according to FDN (rack/slot/port/class)
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

description		6.7.1.1.6
User description of the carrior termination.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

carrierId		6.7.1.1.7
Id of the carrier. (A, B, C, D) Used in XPIC & MIMO configurations to check that the carrier termination is connected to the correct far end carrier termination. Should be the same id on both sides of the hop. Defaulted when not MIMO or XPIC. Sometimes also referred to as preamble
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	a(1), b(2), c(3), d(4), unknown(5)

ctStatus		6.7.1.1.8
The status of the carrier termination, hop
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	down(1), up(2), na(3), unknown(4), degraded(5)

frameId		6.7.1.1.9
A unique identifier for the radio frame to be used. Wanted frameId, txFrequency, rxFrequency, referenceSec, selectedMinAcm and selectedMaxAcm must be a valid combination.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..10000

txFrequency		6.7.1.1.10
Selected frequency on the transmitter (kHz). Wanted frameId, txFrequency, rxFrequency, referenceSec, selectedMinAcm and selectedMaxAcm must be a valid combination.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

minTxFrequency		6.7.1.1.11
Minimum Tx frequency possible to use, given by the selected frame-id
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

maxTxFrequency		6.7.1.1.12
Maximum Tx frequency possible to use, given by the selected frame-id
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

rxFrequency		6.7.1.1.13
Selected frequency on the receiver (kHz). Wanted frameId, txFrequency, rxFrequency, referenceSec, selectedMinAcm and selectedMaxAcm must be a valid combination.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

minRxFrequency		6.7.1.1.14
Minimum Rx frequency possible to use, given by the selected frame-id
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

maxRxFrequency		6.7.1.1.15
Maximum Rx frequency possible to use, given by the selected frame-id
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

frequencyStepSize		6.7.1.1.16
Frequency step size in kHz
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

duplexDistance		6.7.1.1.17
Distance between Tx and Rx frequencies (kHz)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

duplexType		6.7.1.1.18
The duplex type is given by the equipment (Fixed,Variable)
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	variable(1), fixed(2), unknown(3)

duplexConfig		6.7.1.1.19
Enabling or disabling configuration of Rx freq using duplex distance
Status: current	Access: read-write
OBJECT-TYPE
	EnableStatusTC

autoFreqSelection		6.7.1.1.20
Automatic frequency selection mode
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), master(2), slave(3), unknown(4)

autoFreqSelectedChannel		6.7.1.1.21
Automatic frequency selected channel
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

autoFreqSelectionStatus		6.7.1.1.22
Automatic frequency status
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	idle(1), searchingForSlave(2), requestingInfoFromSlave(3), waitingForMaster(4), waitingForChannelInfoRequest(5), inProgress(6), initializing(7), finished(8), failed(9), unknown(10)

channelSpacing		6.7.1.1.23
Channel spacing
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	cs7MHz(1), cs10MHz(2), cs14MHz(3), cs20MHz(4), cs28MHz(5), cs30MHz(6), cs40MHz(7), cs50MHz(8), cs56MHz(9), cs250MHz(10), cs60MHz(11), cs500MHz(12), cs750MHz(13), cs100MHz(14), cs150MHz(15), cs200MHz(16), cs125MHz(17), cs80MHz(18), cs112MHz(19), cs1000MHz(20), cs1250MHz(21), cs1500MHz(22), cs62p5MHz(23), cs2000MHz(24), unknown(25)

polarization		6.7.1.1.24
Antenna polarization
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notSpecified(1), horizontal(2), vertical(3), unknown(4)

txOperStatus		6.7.1.1.25
Operative status of the transmitter
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), off(2), on(3), standby(4)

txAdminStatus		6.7.1.1.26
Administrative status of the transmitter
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(1), on(2), unknown(3)

selectedOutputPowerType		6.7.1.1.27
Selected output power type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	standard(1), high(2), unknown(3)

availableOutputPowerType		6.7.1.1.28
Available output power type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	standard(1), high(2), unknown(3)

selectedMinOutputPower		6.7.1.1.29
Selected min output power. Selected min & max output power should be set to the same value for RTPC mode, otherwise the hop operates in ATPC mode.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

selectedMaxOutputPower		6.7.1.1.30
Selected max output power. Selected min & max output power should be set to the same value for RTPC mode, otherwise the hop operates in ATPC mode.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

availableMinOutputPower		6.7.1.1.31
The minimum output power supported (dBm). The system shows a value if the equipment is available and a frame id has been selected.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

availableMaxOutputPower		6.7.1.1.32
The maximum output power supported (dBm). The system shows a value if the equipment is available and a frame id has been selected.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

referenceSec		6.7.1.1.33
Each modulation is compliant to a Reference Spectrum Efficiency Class (RSEC). When running Adaptive Coding/Modulation, one SEC has to be selected for all the coding/modulations between selectedMinACM and selectedMaxACM. This parameter is called Reference SEC. This setting will affect availableMaxOutputPower, in order to fulfill spectrum requirements. Wanted frameId, txFrequency, rxFrequency, referenceSec, selectedMinAcm and selectedMaxAcm must be a valid combination.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noAvailable(1), sec2(2), sec4L(4), sec4H(5), sec5B(7), sec6B(9), sec5LB(10), sec5HB(11), sec6LB(12), sec6HB(13), sec7B(14), unknown(15)

targetInputPowerFarEnd		6.7.1.1.34
The wanted input power at far end (dBm), when running ATPC
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

berAlarmThreshold		6.7.1.1.35
Threshold for the BER alarm
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	tenExpMinus6(1), tenExpMinus3(2)

inputPowerAlarmThreshold		6.7.1.1.36
Threshold for the input power alarm
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

plannedAlignmentInputPower		6.7.1.1.37
The planned received input power (dBm) dependent upon selected minimum ACM and corresponding output power. Used when doing alignment
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atpcFallback		6.7.1.1.38
Enable or disable the output power fall back function
Status: current	Access: read-write
OBJECT-TYPE
	EnableStatusTC

atpcFallbackTimer		6.7.1.1.39
Specifies the timer for output power fall back (# of seconds)
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

atpcFallbackOutputPower		6.7.1.1.40
The ATPC fallback output power
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

xpicStatus		6.7.1.1.41
Status of the XPIC function.
Status: current	Access: read-only
OBJECT-TYPE
	XpicMimoTC

mimoStatus		6.7.1.1.42
Status of the MIMO function.
Status: current	Access: read-only
OBJECT-TYPE
	XpicMimoTC

actualSnir		6.7.1.1.43
Actual signal to noise plus interference ratio (dB).
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

actualXpi		6.7.1.1.44
The carrier to cross-polar interference level (dBc).
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

actualSi		6.7.1.1.45
Spatial interference between the CTs when MIMO is configured.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

actualTxCapacity		6.7.1.1.46
Actual capacity supported by the carrier termination.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

licensedCapacity		6.7.1.1.47
Wanted or installed license for the capacity allowed for the carrier termination.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

availableMinCapacity		6.7.1.1.48
Minimum capacity possible to use. Given by the selected frame-id (kbit/s)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

availableMaxCapacity		6.7.1.1.49
Maximum capacity possible to use. Given by the selected frame-id (kbit/s)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

selectedMinCapacity		6.7.1.1.50
Selected minimum capacity, derived from selected minimum ACM (kbit/s)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

selectedMaxCapacity		6.7.1.1.51
Selected maximum capacity, derived from selected maximum ACM (kbit/s)
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

wantedLicensedCapacity		6.7.1.1.52
Wanted licensed capacity and creation of LRF for the carrier termination (kbit/s)
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

availableMinAcm		6.7.1.1.53
Minimum ACM possible to use, given by the selected frame id.
Status: current	Access: read-only
OBJECT-TYPE
	AcmTC

availableMaxAcm		6.7.1.1.54
Maximum ACM possible to use, given by the selected frame id
Status: current	Access: read-only
OBJECT-TYPE
	AcmTC

selectedMinAcm		6.7.1.1.55
Selected minimum coding/modulation. If selectedMinACM = selectedMaxACM, then the modulation is fixed
Status: current	Access: read-write
OBJECT-TYPE
	AcmTC

selectedMaxAcm		6.7.1.1.56
Selected maximum coding/modulation. If selectedMinACM = selectedMaxACM, then the modulation is fixed
Status: current	Access: read-write
OBJECT-TYPE
	AcmTC

actualRxAcmTC		6.7.1.1.57
Actual rx modulation and coding
Status: current	Access: read-only
OBJECT-TYPE
	AcmTC

actualTxAcmTC		6.7.1.1.58
Actual tx modulation and coding
Status: current	Access: read-only
OBJECT-TYPE
	AcmTC

alignmentMode		6.7.1.1.59
Enable or disable the alignment mode
Status: current	Access: read-write
OBJECT-TYPE
	EnableStatusTC

rfLoop		6.7.1.1.60
Enable or disable the rf loop
Status: current	Access: read-write
OBJECT-TYPE
	EnableStatusTC

rltTable		6.7.3
A table of RLT Table entries.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RltEntry

rltEntry		6.7.3.1
An entry of RLT application.
Status: current	Access: not-accessible
OBJECT-TYPE
	RltEntry

rltDistinguishedName		6.7.3.1.1
Unique id/name of the radio link termination, according to FDN (rack/slot/port/class)
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

neIpAddress		6.7.3.1.2
NE IP address
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

neIpv6Address		6.7.3.1.3
NE IP V6 address
Status: current	Access: read-only
OBJECT-TYPE
	InetAddressIPv6

neName		6.7.3.1.4
NE Name
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

neType		6.7.3.1.5
NE Type
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), mle(2), xfMle(3), tn(4), cn(5), pt(6)

id		6.7.3.1.6
User defined id of the radio link terminal
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

rltStatus		6.7.3.1.7
The status of the radio link terminal
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	down(1), up(2), na(3), unknown(4), degraded(5)

mode		6.7.3.1.8
The status of the radio link terminal
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	mode1plus0(1), mode1plus1CSB(2), mode1plus1RLP(3), mode2plus0RLB(4), mode2plus1CSB(5), mode2plus1RLP(6), mode2plus2CSB(7), mode2plus2RLP(8), mode3plus0RLB(9), mode4plus0RLB(10), notAvailable11(11), notAvailable12(12), notAvailable13(13), notAvailable14(14), mode3plus1RLP(15), mode3plus2RLP(16), mode3plus3RLP(17), mode4plus1RLP(18), mode4plus2RLP(19), mode4plus3RLP(20), mode4plus4RLP(21), notAvailable22(22), notAvailable23(23), notAvailable24(24), notAvailable25(25), notAvailable26(26), notAvailable27(27), mode3plus1CSB(28), mode3plus2CSB(29), mode3plus3CSB(30), mode4plus1CSB(31), mode4plus2CSB(32), mode4plus3CSB(33), mode4plus4CSB(34), unknown(35)

actualTxTotalCapacity		6.7.3.1.9
Actual aggregated total (packet + TDM) transmitter capacity for the radio link termination. Limited by licenses & configuration (=nearEndLimitedCapacity) and depending on actual modulation/coding used at the moment.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

limitedTotalCapacity		6.7.3.1.10
Maximum total capacity allowed by the current configuration and installed licenses. Aggregated from the constituent carrier termination values.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

protectionStatus		6.7.3.1.11
Status of a protected node.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unprotected(1), protected(2), unableToProtect(3), unknown(4)

revertiveWaitToRestore		6.7.3.1.12
The time, in number of seconds, to wait before switching back to the preferred Tx.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

revertivePreferredTx		6.7.3.1.13
The preferred carrier termination transmitter.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ct11(1), ct12(2), ct21(3), ct22(4), notApplicable(5), unknown(6)

protectionSwitchMode		6.7.3.1.14
.The mode in which the switching mechanism is configured
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	auto(1), manual(2), autoAndRevertive(3), unknown(4), notApplicable(5)

fadeNotificationTimer		6.7.3.1.15
Notification is sent if fading is longer than this timer, applicable for protection.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

expectedFarEndId		6.7.3.1.16
Expected id of far-end terminal
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

farEndIdCheck		6.7.3.1.17
Enabling of far end id check.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2), unknown(3)

cpriMode		6.7.3.1.18
Set the mode of the CPRI front-haul product.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	master(1), slave(2), notApplicable(3), unknown(4)

cpriStatus		6.7.3.1.19
The status of the CPRI front-haul product.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	idle(1), waitingOnRtcSync(2), waitingOnCpri(3), waitingOnRxRequest(4), waitingOnTxRequest(5), inSync(6), unknown(7)

manualSwitch		6.7.3.1.20
Manual switch of protected carrier termination transmitter.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ct11(1), ct12(2), ct21(3), ct22(4), notApplicable(5), unknown(6)

mlhcOperStatus		6.7.3.1.21
Operative status of multi layer header compression.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2), unknown(3)

mlhcAdminStatus		6.7.3.1.22
Administrative status of multi layer header compression.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(1), on(2), unknown(3)

mlhcMplsConfig		6.7.3.1.23
MLHC/MPLS configuration.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	controlWord(1), l2(2), l3(3), mplsOnly(4), unknown(5)

plcOperStatus		6.7.3.1.24
Operative status of payload compression.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2), unknown(3)

plcAdminStatus		6.7.3.1.25
Administrative status of payload compression.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(1), on(2), unknown(3)

ctG826ContinuousTable		6.7.4.1
A table of CT G826 Performance Continuous counters entries. The counters are reset by ctG826Reset
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CtG826ContinuousEntry

ctG826ContinuousEntry		6.7.4.1.1
An entry of CT G826 Performance Continuous counters.
Status: current	Access: not-accessible
OBJECT-TYPE
	CtG826ContinuousEntry

ctG826TimeElapsed		6.7.4.1.1.1
Time elapsed in seconds since last PMReset
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ctBBE		6.7.4.1.1.2
Background Block Errors
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ctBBER		6.7.4.1.1.3
Background Block Errors Ratio
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

ctES		6.7.4.1.1.4
Error seconds
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ctESR		6.7.4.1.1.5
Error seconds Ratio
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

ctSES		6.7.4.1.1.6
Severely error seconds
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ctSESR		6.7.4.1.1.7
Severely error seconds Ratio
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

ctBB		6.7.4.1.1.8
Background blocks
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

ctUAS		6.7.4.1.1.9
Unavailable seconds
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ctG826Reset		6.7.4.1.1.10
Reset the continuous PM counters
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), noReset(2), reset(3)

ctG826Current15mTable		6.7.4.2
A table of CT Performance G826 15 m current counters Table entries.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CtG826Current15mEntry

ctG826Current15mEntry		6.7.4.2.1
An entry of CT Performance G826 15 m current Table counters.
Status: current	Access: not-accessible
OBJECT-TYPE
	CtG826Current15mEntry

ctG826Current15mTimeElapsed		6.7.4.2.1.1
Time elapsed in seconds since last PMReset
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ctCurrent15mBBE		6.7.4.2.1.2
Background Block Errors
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ctCurrent15mBBER		6.7.4.2.1.3
Background Block Errors Ratio
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

ctCurrent15mES		6.7.4.2.1.4
Error seconds
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ctCurrent15mESR		6.7.4.2.1.5
Error seconds Ratio
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

ctCurrent15mSES		6.7.4.2.1.6
Severely error seconds
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ctCurrent15mSESR		6.7.4.2.1.7
Severely error seconds Ratio
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

ctCurrent15mBB		6.7.4.2.1.8
Background blocks
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ctCurrent15mUAS		6.7.4.2.1.9
Unavailable seconds
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ctG826Current24hTable		6.7.4.3
A table of CT Performance G826 Current 24h counters entries.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CtG826Current24hEntry

ctG826Current24hEntry		6.7.4.3.1
An entry of CT Performance G826 Current 24 h counters.
Status: current	Access: not-accessible
OBJECT-TYPE
	CtG826Current24hEntry

ctG826Current24hTimeElapsed		6.7.4.3.1.1
Time elapsed in seconds since last PMReset
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ctCurrent24hBBE		6.7.4.3.1.2
Background Block Errors
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ctCurrent24hBBER		6.7.4.3.1.3
Background Block Errors Ratio
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

ctCurrent24hES		6.7.4.3.1.4
Error seconds
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ctCurrent24hESR		6.7.4.3.1.5
Error seconds Ratio
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

ctCurrent24hSES		6.7.4.3.1.6
Severely error seconds
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ctCurrent24hSESR		6.7.4.3.1.7
Severely error seconds Ratio
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

ctCurrent24hBB		6.7.4.3.1.8
Background blocks
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ctCurrent24hUAS		6.7.4.3.1.9
Unavailable seconds
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ptRadioLinkCompliances		6.7.2.1
OBJECT IDENTIFIER

ptRadioLinkGroups		6.7.2.2
OBJECT IDENTIFIER

ptRadioLinkFullCompliance		6.7.2.1.1
The compliance statement for SNMP entities which implement everything.
Status: current	Access: read-only
MODULE-COMPLIANCE

ptRadioLinkCompleteGroup		6.7.2.2.1
A collection of all current objects in this MIB module.
Status: current	Access: read-only
OBJECT-GROUP