PEA-VDSL-IPDSLAM

File: PEA-VDSL-IPDSLAM.mib (106624 bytes)

Imported modules

DIESEL-SMI PEA-BRIDGE-IPDSLAM PEA-ADSL-IPDSLAM
PEA-EQUIPMENT-IPDSLAM PEM-STANDARD SNMPv2-SMI
SNMPv2-TC SNMPv2-CONF RFC1213-MIB
ADSL-LINE-MIB ADSL-LINE-EXT-MIB

Imported symbols

peaIpDslam lineIndex PerfIntervalCount
PerfCurrentCount AdslPerfCurrDayCount AdslPerfPrevDayCount
messageId errorCode managedObjectClass
managedObjectInstance sequenceNumber perceivedSeverity
eventTime eventTypePem probableCause
MODULE-IDENTITY OBJECT-TYPE NOTIFICATION-TYPE
Gauge32 Integer32 Unsigned32
Counter32 TEXTUAL-CONVENTION TruthValue
OBJECT-GROUP NOTIFICATION-GROUP DisplayString
adslAtucIntervalNumber adslAturIntervalNumber adslAtucChanIntervalNumber
adslAturChanIntervalNumber adslLineConfProfileEntry adslLineAlarmConfProfileEntry
adslAtucThresh15MinESs adslAturThresh15MinESs adslAtucChanCurrTxRate
adslAturChanCurrTxRate adslAtucThreshold15MinSesL adslAtucThreshold15MinUasL
adslAturThreshold15MinSesL adslAturThreshold15MinUasL

Defined Types

Vdsl2Direction  
Identifies the direction of a band as being either upstream or downstream. Specified as an INTEGER, the two values are: upstream(1) downstream(2)
TEXTUAL-CONVENTION    
  INTEGER upstream(1), downstream(2)  

SnmpAdminString  
An octet string containing administrative information, preferably in human-readable form. To facilitate internationalization, this information is represented using the ISO/IEC IS 10646-1 character set, encoded as an octet string using the UTF-8 transformation format described in [RFC2279]. Since additional code points are added by amendments to the 10646 standard from time to time, implementations must be prepared to encounter any code point from 0x00000000 to 0x7fffffff. Byte sequences that do not correspond to the valid UTF-8 encoding of a code point or are outside this range are prohibited. The use of control codes should be avoided. When it is necessary to represent a newline, the control code sequence CR LF should be used. The use of leading or trailing white space should be avoided. For code points not directly supported by user interface hardware or software, an alternative means of entry and display, such as hexadecimal, may be provided. For information encoded in 7-bit US-ASCII, the UTF-8 encoding is identical to the US-ASCII encoding. UTF-8 may require multiple bytes to represent a single character / code point; thus the length of this object in octets may be different from the number of characters encoded. Similarly, size constraints refer to the number of encoded octets, not the number of characters represented by an encoding. Note that when this TC is used for an object that is used or envisioned to be used as an index, then a SIZE restriction MUST be specified so that the number of sub-identifiers for any object instance does not exceed the limit of 128, as defined by [RFC1905]. Note that the size of an SnmpAdminString object is measured in octets, not characters.
TEXTUAL-CONVENTION    
  OCTET STRING Size(0..255)  

VdslLineConfPhysVdslLimitingMaskDnEntry  
SEQUENCE    
  limitingMaskDnNoOfBreakPoints INTEGER
  limitingMaskDnBpToneIndex OCTET STRING
  limitingMaskDnBpPsd OCTET STRING
  limitingMaskDnBypassOutbandPsdFilter TruthValue

VdslLineConfPhysVdslLimitingMaskUpEntry  
SEQUENCE    
  limitingMaskUpNoOfBreakPoints INTEGER
  limitingMaskUpBpToneIndex OCTET STRING
  limitingMaskUpBpPsd OCTET STRING
  limitingMaskUpUseIsdnTypeUS0 TruthValue

VdslLineConfPhysVdslBandPlanDnEntry  
SEQUENCE    
  bandPlanDnNoOfToneGroups INTEGER
  bandPlanDnToneGroups0StartTone INTEGER
  bandPlanDnToneGroups0EndTone INTEGER
  bandPlanDnToneGroups1StartTone INTEGER
  bandPlanDnToneGroups1EndTone INTEGER
  bandPlanDnToneGroups2StartTone INTEGER
  bandPlanDnToneGroups2EndTone INTEGER

VdslLineConfPhysVdslBandPlanUpEntry  
SEQUENCE    
  bandPlanUpNoOfToneGroups INTEGER
  bandPlanUpToneGroups0StartTone INTEGER
  bandPlanUpToneGroups0EndTone INTEGER
  bandPlanUpToneGroups1StartTone INTEGER
  bandPlanUpToneGroups1EndTone INTEGER
  bandPlanUpToneGroups2StartTone INTEGER
  bandPlanUpToneGroups2EndTone INTEGER

VdslLineConfPhysVdslInBandNotchesEntry  
SEQUENCE    
  inBandNotchesNoOfToneGroups INTEGER
  inBandNotchesToneGroups0StartTone INTEGER
  inBandNotchesToneGroups0EndTone INTEGER
  inBandNotchesToneGroups1StartTone INTEGER
  inBandNotchesToneGroups1EndTone INTEGER
  inBandNotchesToneGroups2StartTone INTEGER
  inBandNotchesToneGroups2EndTone INTEGER
  inBandNotchesToneGroups3StartTone INTEGER
  inBandNotchesToneGroups3EndTone INTEGER
  inBandNotchesToneGroups4StartTone INTEGER
  inBandNotchesToneGroups4EndTone INTEGER
  inBandNotchesToneGroups5StartTone INTEGER
  inBandNotchesToneGroups5EndTone INTEGER
  inBandNotchesToneGroups6StartTone INTEGER
  inBandNotchesToneGroups6EndTone INTEGER
  inBandNotchesToneGroups7StartTone INTEGER
  inBandNotchesToneGroups7EndTone INTEGER

VdslLineConfPhysVdslRfiNotchesEntry  
SEQUENCE    
  rfiNotchesNoOfToneGroups INTEGER
  rfiNotchesToneGroups0StartTone INTEGER
  rfiNotchesToneGroups0EndTone INTEGER
  rfiNotchesToneGroups1StartTone INTEGER
  rfiNotchesToneGroups1EndTone INTEGER
  rfiNotchesToneGroups2StartTone INTEGER
  rfiNotchesToneGroups2EndTone INTEGER
  rfiNotchesToneGroups3StartTone INTEGER
  rfiNotchesToneGroups3EndTone INTEGER
  rfiNotchesToneGroups4StartTone INTEGER
  rfiNotchesToneGroups4EndTone INTEGER
  rfiNotchesToneGroups5StartTone INTEGER
  rfiNotchesToneGroups5EndTone INTEGER
  rfiNotchesToneGroups6StartTone INTEGER
  rfiNotchesToneGroups6EndTone INTEGER
  rfiNotchesToneGroups7StartTone INTEGER
  rfiNotchesToneGroups7EndTone INTEGER
  rfiNotchesToneGroups8StartTone INTEGER
  rfiNotchesToneGroups8EndTone INTEGER
  rfiNotchesToneGroups9StartTone INTEGER
  rfiNotchesToneGroups9EndTone INTEGER
  rfiNotchesToneGroups10StartTone INTEGER
  rfiNotchesToneGroups10EndTone INTEGER
  rfiNotchesToneGroups11StartTone INTEGER
  rfiNotchesToneGroups11EndTone INTEGER
  rfiNotchesToneGroups12StartTone INTEGER
  rfiNotchesToneGroups12EndTone INTEGER
  rfiNotchesToneGroups13StartTone INTEGER
  rfiNotchesToneGroups13EndTone INTEGER
  rfiNotchesToneGroups14StartTone INTEGER
  rfiNotchesToneGroups14EndTone INTEGER
  rfiNotchesToneGroups15StartTone INTEGER
  rfiNotchesToneGroups15EndTone INTEGER

VdslLineConfPhysVdslPboPsdUpEntry  
SEQUENCE    
  vdslLineConfPhysVdslPboPsdUpNoOfToneGroups INTEGER
  vdslLineConfPhysVdslPboPsdUpGroup0A INTEGER
  vdslLineConfPhysVdslPboPsdUpGroup1A INTEGER
  vdslLineConfPhysVdslPboPsdUpGroup2A INTEGER
  vdslLineConfPhysVdslPboPsdUpGroup0B INTEGER
  vdslLineConfPhysVdslPboPsdUpGroup1B INTEGER
  vdslLineConfPhysVdslPboPsdUpGroup2B INTEGER
  vdslLineConfPhysVdslPboPsdUpForceElectricalLength INTEGER
  vdslLineConfPhysVdslPboPsdUpAdvanced TruthValue
  vdslLineConfPhysVdslPboPsdUpDisable TruthValue

VdslLineConfPhysVdslMiscVdslConfEntry  
SEQUENCE    
  miscVdslConfForceElectricalLength INTEGER
  miscVdslConfMaxTxPowerDn INTEGER
  miscVdslConfDisableBitRateLimitation TruthValue
  miscVdslConfDisableVdslUsPbo TruthValue
  miscVdslConfDynamicInterleaverUs TruthValue
  miscVdslConfDynamicInterleaverDs TruthValue
  miscVdslConfDisableProfileBitmap INTEGER
  miscVdslConfEnableProfileBitmap BITS
  miscVdslConfigStandardLimitMask INTEGER

VdslVtucProprietaryChanXEntry  
SEQUENCE    
  vdslVtucProprietaryChanXI Unsigned32
  vdslVtucProprietaryChanXG Unsigned32
  vdslVtucProprietaryChanXU Unsigned32
  vdslVtucProprietaryChanXF Unsigned32
  vdslVtucProprietaryChanXTpsTcTypeB0 INTEGER
  vdslVtucProprietaryChanXTpsTcTypeB1 INTEGER

VdslVturProprietaryChanXEntry  
SEQUENCE    
  vdslVturProprietaryChanXI Unsigned32
  vdslVturProprietaryChanXG Unsigned32
  vdslVturProprietaryChanXU Unsigned32
  vdslVturProprietaryChanXF Unsigned32

VdslLineStatusPhysVdslBandPlanDnEntry  
SEQUENCE    
  statusBandPlanDnNoOfToneGroups INTEGER
  statusBandPlanDnToneGroups0StartTone INTEGER
  statusBandPlanDnToneGroups0EndTone INTEGER
  statusBandPlanDnToneGroups1StartTone INTEGER
  statusBandPlanDnToneGroups1EndTone INTEGER
  statusBandPlanDnToneGroups2StartTone INTEGER
  statusBandPlanDnToneGroups2EndTone INTEGER

VdslLineStatusPhysVdslBandPlanUpEntry  
SEQUENCE    
  statusBandPlanUpNoOfToneGroups INTEGER
  statusBandPlanUpToneGroups0StartTone INTEGER
  statusBandPlanUpToneGroups0EndTone INTEGER
  statusBandPlanUpToneGroups1StartTone INTEGER
  statusBandPlanUpToneGroups1EndTone INTEGER
  statusBandPlanUpToneGroups2StartTone INTEGER
  statusBandPlanUpToneGroups2EndTone INTEGER

VdslLineConfPhysVdslPboPsdDnEntry  
SEQUENCE    
  vdslLineConfPhysVdslPboPsdDnEsel INTEGER
  vdslLineConfPhysVdslPboPsdDnEscmA INTEGER
  vdslLineConfPhysVdslPboPsdDnEscmB INTEGER
  vdslLineConfPhysVdslPboPsdDnEscmC INTEGER
  vdslLineConfPhysVdslPboPsdDnFmin INTEGER
  vdslLineConfPhysVdslPboPsdDnFmax INTEGER
  vdslLineConfPhysVdslPboPsdDnMus INTEGER
  vdslLineConfPhysVdslPboPsdDnAdvanced TruthValue
  vdslLineConfPhysVdslPboPsdDnEselMin INTEGER

VdslLineConfPhysVdslMibMaskDsEntry  
SEQUENCE    
  mibMaskDsNoOfBreakPoints INTEGER
  mibMaskDsBpToneIndex OCTET STRING
  mibMaskDsBpPsd OCTET STRING

VdslLineConfPhysVdslMibMaskUsEntry  
SEQUENCE    
  mibMaskUsNoOfBreakPoints INTEGER
  mibMaskUsBpToneIndex OCTET STRING
  mibMaskUsBpPsd OCTET STRING

VdslProprietaryLineConfProfileXEntry  
SEQUENCE    
  vdslVtucProprietaryConfXTpsTcType INTEGER
  vdslVtucProprietaryConfXPreemtionAllowedB0 TruthValue
  vdslVtucProprietaryConfXPreemtionAllowedB1 TruthValue

VdslVtucChanIntervalXEntry  
SEQUENCE    
  vdslVtucChanIntervalXPtmCrcErrors PerfIntervalCount
  vdslVtucChanIntervalXPtmCrcErrorsP PerfIntervalCount
  vdslVtucChanIntervalXPtmCv PerfIntervalCount
  vdslVtucChanIntervalXPtmCvP PerfIntervalCount

VdslVturChanIntervalXEntry  
SEQUENCE    
  vdslVturChanIntervalXPtmCrcErrors PerfIntervalCount
  vdslVturChanIntervalXPtmCrcErrorsP PerfIntervalCount
  vdslVturChanIntervalXPtmCv PerfIntervalCount
  vdslVturChanIntervalXPtmCvP PerfIntervalCount

VdslVtucChanPerfDataXEntry  
SEQUENCE    
  vdslVtucChanIntervalXCurr15MinPtmCrcErrors PerfCurrentCount
  vdslVtucChanIntervalXCurr1DayPtmCrcErrors AdslPerfCurrDayCount
  vdslVtucChanIntervalXPrev1DayPtmCrcErrors AdslPerfPrevDayCount
  vdslVtucChanIntervalXCurr15MinPtmCrcErrorsP PerfCurrentCount
  vdslVtucChanIntervalXCurr1DayPtmCrcErrorsP AdslPerfCurrDayCount
  vdslVtucChanIntervalXPrev1DayPtmCrcErrorsP AdslPerfPrevDayCount
  vdslVtucChanIntervalXCurr15MinPtmCv PerfCurrentCount
  vdslVtucChanIntervalXCurr1DayPtmCv AdslPerfCurrDayCount
  vdslVtucChanIntervalXPrev1DayPtmCv AdslPerfPrevDayCount
  vdslVtucChanIntervalXCurr15MinPtmCvP PerfCurrentCount
  vdslVtucChanIntervalXCurr1DayPtmCvP AdslPerfCurrDayCount
  vdslVtucChanIntervalXPrev1DayPtmCvP AdslPerfPrevDayCount

VdslVturChanPerfDataXEntry  
SEQUENCE    
  vdslVturChanIntervalXCurr15MinPtmCrcErrors PerfCurrentCount
  vdslVturChanIntervalXCurr1DayPtmCrcErrors AdslPerfCurrDayCount
  vdslVturChanIntervalXPrev1DayPtmCrcErrors AdslPerfPrevDayCount
  vdslVturChanIntervalXCurr15MinPtmCrcErrorsP PerfCurrentCount
  vdslVturChanIntervalXCurr1DayPtmCrcErrorsP AdslPerfCurrDayCount
  vdslVturChanIntervalXPrev1DayPtmCrcErrorsP AdslPerfPrevDayCount
  vdslVturChanIntervalXCurr15MinPtmCv PerfCurrentCount
  vdslVturChanIntervalXCurr1DayPtmCv AdslPerfCurrDayCount
  vdslVturChanIntervalXPrev1DayPtmCv AdslPerfPrevDayCount
  vdslVturChanIntervalXCurr15MinPtmCvP PerfCurrentCount
  vdslVturChanIntervalXCurr1DayPtmCvP AdslPerfCurrDayCount
  vdslVturChanIntervalXPrev1DayPtmCvP AdslPerfPrevDayCount

Vdsl2SCStatusEntry  
SEQUENCE    
  vdsl2SCStatusDirection Vdsl2Direction
  vdsl2SCStatusSegment Unsigned32
  vdsl2SCStatusSnr OCTET STRING
  vdsl2SCStatusBitsAlloc OCTET STRING
  vdsl2SCStatusGainAlloc OCTET STRING

Vdsl2ChConfProfileEntry  
SEQUENCE    
  vdsl2ChConfProfProfileName SnmpAdminString
  vdsl2ChConfProfMinResDataRateDs Unsigned32
  vdsl2ChConfProfMinResDataRateUs Unsigned32

VdslLineMiscPhysStatusEntry  
SEQUENCE    
  miscPhysStatusVdslProfileBitmap BITS

Defined Values

peaVdslIpDslam 1.3.6.1.4.1.193.72.300.80
The IP DSLAM software supports a number of standard and proprietary MIBs. This MIB module defines objects for the management of a pair of VDSL modems at each end of the VDSL line. For general DSL purposes the ADSL-LINE-MIB (RFC2662 and RFC3440) is used supplemented with the PEA-ADSL-IPDSLAM. The reason for this MIB module is that a new ADSL2/VDSL2 specific ADSL LINE MIB is yet not available from IETF.
MODULE-IDENTITY    

vdslObjects 1.3.6.1.4.1.193.72.300.80.1
OBJECT IDENTIFIER    

vdsl2Status 1.3.6.1.4.1.193.72.300.80.2
OBJECT IDENTIFIER    

vdsl2ProfileChannel 1.3.6.1.4.1.193.72.300.80.3
OBJECT IDENTIFIER    

vdslLineConfPhysVdslLimitingMaskDnTable 1.3.6.1.4.1.193.72.300.80.1.1
This table contains information of LimitingMaskDn configuration
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VdslLineConfPhysVdslLimitingMaskDnEntry

vdslLineConfPhysVdslLimitingMaskDnEntry 1.3.6.1.4.1.193.72.300.80.1.1.1
An entry in vdslLineConfPhysVdslLimitingMaskDnTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VdslLineConfPhysVdslLimitingMaskDnEntry  

limitingMaskDnNoOfBreakPoints 1.3.6.1.4.1.193.72.300.80.1.1.1.1
Number of breakpoints in downstream mask
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..32  

limitingMaskDnBpToneIndex 1.3.6.1.4.1.193.72.300.80.1.1.1.2
Toneindexes for 32 breakpoints. The octet string has the format: [Bp0_Hi, Bp0_Low....Bp31_Hi, Bp31_Low] Valid range is [0, 4096]
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(64)  

limitingMaskDnBpPsd 1.3.6.1.4.1.193.72.300.80.1.1.1.3
PSD level in 0.1 dBm/Hz for 32 breakpoints. Valid range is [0,-96] dBm/Hz. The octet string has the format: [Bp0_Hi, Bp0_Low....Bp31_Hi, Bp31_Low]
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(64)  

limitingMaskDnBypassOutbandPsdFilter 1.3.6.1.4.1.193.72.300.80.1.1.1.4
If set, the extra filter will be bypassed at the expense of more OOB above 17.5MHz.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

vdslLineConfPhysVdslLimitingMaskUpTable 1.3.6.1.4.1.193.72.300.80.1.2
This table contains information of LimitingMaskUp configuration
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VdslLineConfPhysVdslLimitingMaskUpEntry

vdslLineConfPhysVdslLimitingMaskUpEntry 1.3.6.1.4.1.193.72.300.80.1.2.1
An entry in vdslLineConfPhysVdslLimitingMaskUpTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VdslLineConfPhysVdslLimitingMaskUpEntry  

limitingMaskUpNoOfBreakPoints 1.3.6.1.4.1.193.72.300.80.1.2.1.1
Number of breakpoints in upstream mask
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..16  

limitingMaskUpBpToneIndex 1.3.6.1.4.1.193.72.300.80.1.2.1.2
Toneindexes for 16 breakpoints. The octet string has the format: [Bp0_Hi, Bp0_Low....Bp31_Hi, Bp31_Low] Valid range is [0, 4096]
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(32)  

limitingMaskUpBpPsd 1.3.6.1.4.1.193.72.300.80.1.2.1.3
PSD level in 0.1 dBm/Hz for 16 breakpoints. Valid range is [0,-96] dBm/Hz. The octet string has the format: [Bp0_Hi, Bp0_Low....Bp31_Hi, Bp31_Low]
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(32)  

limitingMaskUpUseIsdnTypeUS0 1.3.6.1.4.1.193.72.300.80.1.2.1.4
If set it indicates that an ISDN type US0 has to be negociated, else POTS type is used (default).
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

vdslLineConfPhysVdslBandPlanDnTable 1.3.6.1.4.1.193.72.300.80.1.3
This table contains information of BandPlanDn configuration
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VdslLineConfPhysVdslBandPlanDnEntry

vdslLineConfPhysVdslBandPlanDnEntry 1.3.6.1.4.1.193.72.300.80.1.3.1
An entry in vdslLineConfPhysVdslBandPlanDnTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VdslLineConfPhysVdslBandPlanDnEntry  

bandPlanDnNoOfToneGroups 1.3.6.1.4.1.193.72.300.80.1.3.1.1
Number of bands downstream
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..3  

bandPlanDnToneGroups0StartTone 1.3.6.1.4.1.193.72.300.80.1.3.1.2
Start tone for this band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

bandPlanDnToneGroups0EndTone 1.3.6.1.4.1.193.72.300.80.1.3.1.3
End tone for this band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

bandPlanDnToneGroups1StartTone 1.3.6.1.4.1.193.72.300.80.1.3.1.4
Start tone for this band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

bandPlanDnToneGroups1EndTone 1.3.6.1.4.1.193.72.300.80.1.3.1.5
End tone for this band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

bandPlanDnToneGroups2StartTone 1.3.6.1.4.1.193.72.300.80.1.3.1.6
Start tone for this band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

bandPlanDnToneGroups2EndTone 1.3.6.1.4.1.193.72.300.80.1.3.1.7
End tone for this band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

vdslLineConfPhysVdslBandPlanUpTable 1.3.6.1.4.1.193.72.300.80.1.4
This table contains information of BandPlanUp configuration
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VdslLineConfPhysVdslBandPlanUpEntry

vdslLineConfPhysVdslBandPlanUpEntry 1.3.6.1.4.1.193.72.300.80.1.4.1
An entry in vdslLineConfPhysVdslBandPlanUpTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VdslLineConfPhysVdslBandPlanUpEntry  

bandPlanUpNoOfToneGroups 1.3.6.1.4.1.193.72.300.80.1.4.1.1
Number of bands downstream
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..3  

bandPlanUpToneGroups0StartTone 1.3.6.1.4.1.193.72.300.80.1.4.1.2
Start tone for this band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

bandPlanUpToneGroups0EndTone 1.3.6.1.4.1.193.72.300.80.1.4.1.3
End tone for this band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

bandPlanUpToneGroups1StartTone 1.3.6.1.4.1.193.72.300.80.1.4.1.4
Start tone for this band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

bandPlanUpToneGroups1EndTone 1.3.6.1.4.1.193.72.300.80.1.4.1.5
End tone for this band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

bandPlanUpToneGroups2StartTone 1.3.6.1.4.1.193.72.300.80.1.4.1.6
Start tone for this band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

bandPlanUpToneGroups2EndTone 1.3.6.1.4.1.193.72.300.80.1.4.1.7
End tone for this band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

vdslLineConfPhysVdslInBandNotchesTable 1.3.6.1.4.1.193.72.300.80.1.5
This table contains information of InBandNotches configuration
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VdslLineConfPhysVdslInBandNotchesEntry

vdslLineConfPhysVdslInBandNotchesEntry 1.3.6.1.4.1.193.72.300.80.1.5.1
An entry in vdslLineConfPhysVdslInBandNotchesTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VdslLineConfPhysVdslInBandNotchesEntry  

inBandNotchesNoOfToneGroups 1.3.6.1.4.1.193.72.300.80.1.5.1.1
Number of InBand bands
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..8  

inBandNotchesToneGroups0StartTone 1.3.6.1.4.1.193.72.300.80.1.5.1.2
Start tone for this band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

inBandNotchesToneGroups0EndTone 1.3.6.1.4.1.193.72.300.80.1.5.1.3
End tone for this band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

inBandNotchesToneGroups1StartTone 1.3.6.1.4.1.193.72.300.80.1.5.1.4
Start tone for this band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

inBandNotchesToneGroups1EndTone 1.3.6.1.4.1.193.72.300.80.1.5.1.5
End tone for this band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

inBandNotchesToneGroups2StartTone 1.3.6.1.4.1.193.72.300.80.1.5.1.6
Start tone for this band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

inBandNotchesToneGroups2EndTone 1.3.6.1.4.1.193.72.300.80.1.5.1.7
End tone for this band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

inBandNotchesToneGroups3StartTone 1.3.6.1.4.1.193.72.300.80.1.5.1.8
Start tone for this band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

inBandNotchesToneGroups3EndTone 1.3.6.1.4.1.193.72.300.80.1.5.1.9
End tone for this band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

inBandNotchesToneGroups4StartTone 1.3.6.1.4.1.193.72.300.80.1.5.1.10
Start tone for this band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

inBandNotchesToneGroups4EndTone 1.3.6.1.4.1.193.72.300.80.1.5.1.11
End tone for this band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

inBandNotchesToneGroups5StartTone 1.3.6.1.4.1.193.72.300.80.1.5.1.12
Start tone for this band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

inBandNotchesToneGroups5EndTone 1.3.6.1.4.1.193.72.300.80.1.5.1.13
End tone for this band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

inBandNotchesToneGroups6StartTone 1.3.6.1.4.1.193.72.300.80.1.5.1.14
Start tone for this band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

inBandNotchesToneGroups6EndTone 1.3.6.1.4.1.193.72.300.80.1.5.1.15
End tone for this band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

inBandNotchesToneGroups7StartTone 1.3.6.1.4.1.193.72.300.80.1.5.1.16
Start tone for this band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

inBandNotchesToneGroups7EndTone 1.3.6.1.4.1.193.72.300.80.1.5.1.17
End tone for this band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

vdslLineConfPhysVdslRfiNotchesTable 1.3.6.1.4.1.193.72.300.80.1.6
This table contains information of RfiNotches configuration
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VdslLineConfPhysVdslRfiNotchesEntry

vdslLineConfPhysVdslRfiNotchesEntry 1.3.6.1.4.1.193.72.300.80.1.6.1
An entry in vdslLineConfPhysVdslRfiNotchesTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VdslLineConfPhysVdslRfiNotchesEntry  

rfiNotchesNoOfToneGroups 1.3.6.1.4.1.193.72.300.80.1.6.1.1
Number of Rfi bands
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..16  

rfiNotchesToneGroups0StartTone 1.3.6.1.4.1.193.72.300.80.1.6.1.2
Start tone for this Rfi band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

rfiNotchesToneGroups0EndTone 1.3.6.1.4.1.193.72.300.80.1.6.1.3
End tone for this Rfi band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

rfiNotchesToneGroups1StartTone 1.3.6.1.4.1.193.72.300.80.1.6.1.4
Start tone for this Rfi band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

rfiNotchesToneGroups1EndTone 1.3.6.1.4.1.193.72.300.80.1.6.1.5
End tone for this Rfi band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

rfiNotchesToneGroups2StartTone 1.3.6.1.4.1.193.72.300.80.1.6.1.6
Start tone for this Rfi band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

rfiNotchesToneGroups2EndTone 1.3.6.1.4.1.193.72.300.80.1.6.1.7
End tone for this Rfi band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

rfiNotchesToneGroups3StartTone 1.3.6.1.4.1.193.72.300.80.1.6.1.8
Start tone for this Rfi band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

rfiNotchesToneGroups3EndTone 1.3.6.1.4.1.193.72.300.80.1.6.1.9
End tone for this Rfi band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

rfiNotchesToneGroups4StartTone 1.3.6.1.4.1.193.72.300.80.1.6.1.10
Start tone for this Rfi band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

rfiNotchesToneGroups4EndTone 1.3.6.1.4.1.193.72.300.80.1.6.1.11
End tone for this Rfi band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

rfiNotchesToneGroups5StartTone 1.3.6.1.4.1.193.72.300.80.1.6.1.12
Start tone for this Rfi band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

rfiNotchesToneGroups5EndTone 1.3.6.1.4.1.193.72.300.80.1.6.1.13
End tone for this Rfi band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

rfiNotchesToneGroups6StartTone 1.3.6.1.4.1.193.72.300.80.1.6.1.14
Start tone for this Rfi band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

rfiNotchesToneGroups6EndTone 1.3.6.1.4.1.193.72.300.80.1.6.1.15
End tone for this Rfi band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

rfiNotchesToneGroups7StartTone 1.3.6.1.4.1.193.72.300.80.1.6.1.16
Start tone for this Rfi band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

rfiNotchesToneGroups7EndTone 1.3.6.1.4.1.193.72.300.80.1.6.1.17
End tone for this Rfi band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

rfiNotchesToneGroups8StartTone 1.3.6.1.4.1.193.72.300.80.1.6.1.18
Start tone for this Rfi band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

rfiNotchesToneGroups8EndTone 1.3.6.1.4.1.193.72.300.80.1.6.1.19
End tone for this Rfi band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

rfiNotchesToneGroups9StartTone 1.3.6.1.4.1.193.72.300.80.1.6.1.20
Start tone for this Rfi band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

rfiNotchesToneGroups9EndTone 1.3.6.1.4.1.193.72.300.80.1.6.1.21
End tone for this Rfi band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

rfiNotchesToneGroups10StartTone 1.3.6.1.4.1.193.72.300.80.1.6.1.22
Start tone for this Rfi band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

rfiNotchesToneGroups10EndTone 1.3.6.1.4.1.193.72.300.80.1.6.1.23
End tone for this Rfi band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

rfiNotchesToneGroups11StartTone 1.3.6.1.4.1.193.72.300.80.1.6.1.24
Start tone for this Rfi band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

rfiNotchesToneGroups11EndTone 1.3.6.1.4.1.193.72.300.80.1.6.1.25
End tone for this Rfi band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

rfiNotchesToneGroups12StartTone 1.3.6.1.4.1.193.72.300.80.1.6.1.26
Start tone for this Rfi band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

rfiNotchesToneGroups12EndTone 1.3.6.1.4.1.193.72.300.80.1.6.1.27
End tone for this Rfi band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

rfiNotchesToneGroups13StartTone 1.3.6.1.4.1.193.72.300.80.1.6.1.28
Start tone for this Rfi band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

rfiNotchesToneGroups13EndTone 1.3.6.1.4.1.193.72.300.80.1.6.1.29
End tone for this Rfi band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

rfiNotchesToneGroups14StartTone 1.3.6.1.4.1.193.72.300.80.1.6.1.30
Start tone for this Rfi band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

rfiNotchesToneGroups14EndTone 1.3.6.1.4.1.193.72.300.80.1.6.1.31
End tone for this Rfi band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

rfiNotchesToneGroups15StartTone 1.3.6.1.4.1.193.72.300.80.1.6.1.32
Start tone for this Rfi band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

rfiNotchesToneGroups15EndTone 1.3.6.1.4.1.193.72.300.80.1.6.1.33
End tone for this Rfi band
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4096  

vdslLineConfPhysVdslPboPsdUpTable 1.3.6.1.4.1.193.72.300.80.1.7
This table contains information of PboPsdUp configuration. Ai and Bi for three upstream bands, not counting US0. A and B are used by the upstream PBO algorithm as in G993.2, par. 7.2.4. The implementation is according to G.997.1 (third revision) section 7.3.1.2.14. The parameters will be substituted by XDSL2 Line MIB parameters.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VdslLineConfPhysVdslPboPsdUpEntry

vdslLineConfPhysVdslPboPsdUpEntry 1.3.6.1.4.1.193.72.300.80.1.7.1
An entry in vdslLineConfPhysVdslPboPsdUpTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VdslLineConfPhysVdslPboPsdUpEntry  

vdslLineConfPhysVdslPboPsdUpNoOfToneGroups 1.3.6.1.4.1.193.72.300.80.1.7.1.1
Number of tone groups in the descriptor. Maximum is three. Must be equal to the number of upstream bands in the bandplan, not counting US0.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..3  

vdslLineConfPhysVdslPboPsdUpGroup0A 1.3.6.1.4.1.193.72.300.80.1.7.1.2
A value of US1. A/256 is the actual value and should be in [-40, -80.96]. G.997.1 name: UPBOPSD-pb (per band).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER -20725..-10240 | 0  

vdslLineConfPhysVdslPboPsdUpGroup1A 1.3.6.1.4.1.193.72.300.80.1.7.1.3
A value of US2. A/256 is the actual value and should be in [-40, -80.96]. G.997.1 name: UPBOPSD-pb (per band).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER -20725..-10240 | 0  

vdslLineConfPhysVdslPboPsdUpGroup2A 1.3.6.1.4.1.193.72.300.80.1.7.1.4
A value of US3. A/256 is the actual value and should be in [-40, -80.96]. Should be 0 if noOfToneGroups < 3. G.997.1 name: UPBOPSD-pb (per band).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER -20725..-10240 | 0  

vdslLineConfPhysVdslPboPsdUpGroup0B 1.3.6.1.4.1.193.72.300.80.1.7.1.5
A value of US1. B/256 is the actual value and should be in [-40, 0]. G.997.1 name: UPBOPSD-pb (per band).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER -10240..0  

vdslLineConfPhysVdslPboPsdUpGroup1B 1.3.6.1.4.1.193.72.300.80.1.7.1.6
A value of US2. B/256 is the actual value and should be in [-40, 0]. G.997.1 name: UPBOPSD-pb (per band).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER -10240..0  

vdslLineConfPhysVdslPboPsdUpGroup2B 1.3.6.1.4.1.193.72.300.80.1.7.1.7
A value of US3. B/256 is the actual value and should be in [-40, 0]. Should be 0 if noOfToneGroups < 3. G.997.1 name: UPBOPSD-pb (per band).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER -10240..0  

vdslLineConfPhysVdslPboPsdUpForceElectricalLength 1.3.6.1.4.1.193.72.300.80.1.7.1.10
If set, this electrical length (unit in 0.1 dB) will be enforced by the CO on the CPE, resulting in a predefined US PBO. If !=0, enforce US PBO corresponding to a line whose attenuation at 1MHz equals this number. Valid range [0,127] dB. A negative value of -1 mean: don't force the electrical length, but use the measured value instead. G.997.1 name: UPBOKL. G.997.1 name: UPBOKLF.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER -1..1270  

vdslLineConfPhysVdslPboPsdUpAdvanced 1.3.6.1.4.1.193.72.300.80.1.7.1.15
Enables an alternative UPBOMASK calculation, which differs from the standard G.997.1 PBO mask calculation.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

vdslLineConfPhysVdslPboPsdUpDisable 1.3.6.1.4.1.193.72.300.80.1.7.1.20
Disable VDSL US power back off, forcing the CPE to use the max US PSD as template. Default not disabled.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

vdslLineConfPhysVdslMiscVdslConfTable 1.3.6.1.4.1.193.72.300.80.1.8
This table contains information of MiscVdslConf configuration
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VdslLineConfPhysVdslMiscVdslConfEntry

vdslLineConfPhysVdslMiscVdslConfEntry 1.3.6.1.4.1.193.72.300.80.1.8.1
An entry in vdslLineConfPhysVdslMiscVdslConfTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VdslLineConfPhysVdslMiscVdslConfEntry  

miscVdslConfForceElectricalLength 1.3.6.1.4.1.193.72.300.80.1.8.1.1
If set, this electrical length (unit in 0.1 dB) will be enforced by the CO on the CPE, resulting in a predefined US PBO. If !=0, enforce US PBO corresponding to a line whose attenuation at 1MHz equals this number. Valid range [0,127] dB. A negative value of -1 mean: don't force the electrical length, but use the measured value instead, to be sent in O-UPDATE Substituted by: vdslLineConfPhysVdslPboPsdUpForceElectricalLength. Obsoleted from: EDA 4.0
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER -1..1270  

miscVdslConfMaxTxPowerDn 1.3.6.1.4.1.193.72.300.80.1.8.1.2
Maximum allowed downstream transmit power. Unit is 0.1 dBm. Valid range [-25.6, 25.6] dBm.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER -256..256  

miscVdslConfDisableBitRateLimitation 1.3.6.1.4.1.193.72.300.80.1.8.1.3
Disables the rate limitation. Only to be used for test purposes. Note that disabling the limitation on more lines may lead to a crash.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

miscVdslConfDisableVdslUsPbo 1.3.6.1.4.1.193.72.300.80.1.8.1.4
Disable VDSL US power back off, forcing the CPE to use the max US PSD as template. Default not disabled. Substituted by: vdslLineConfPhysVdslPboPsdUpDisable. Obsoleted from: EDA 4.0
Status: obsolete Access: read-write
OBJECT-TYPE    
  TruthValue  

miscVdslConfDynamicInterleaverUs 1.3.6.1.4.1.193.72.300.80.1.8.1.5
Enable support of dynamic change of interleaver depth in the upstream direction. Note: This field is specific to VDSL2 mode.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

miscVdslConfDynamicInterleaverDs 1.3.6.1.4.1.193.72.300.80.1.8.1.6
Enable support of dynamic change of interleaver depth in the downstream direction. Note: This field is specific to VDSL2 mode.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

miscVdslConfDisableProfileBitmap 1.3.6.1.4.1.193.72.300.80.1.8.1.7
Bitmap of VDSL2 profiles to be masked The bits are ordered as in G994.1: bit0 = 8a bit6 = 17a Set the respective bit to disable the profile. Note: This field is specific to VDSL2 mode. Substituted by miscVdslConfEnableProfileBitmap which is standard compliant . Obsoleted from: EDA 4.0
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER 0..256  

miscVdslConfEnableProfileBitmap 1.3.6.1.4.1.193.72.300.80.1.8.1.10
VDSL2 profiles to be allowed by the near-end xTU on this line. It is coded in a bit map representation (0 if not allowed, 1 if allowed) as defined in G.997.1 (third revision), section 7.3.1.1.11: NOTE that profile 30a is not supported in EDA. BIT PROFILE 7 G.993.2 Profile 8a. 6 G.993.2 Profile 8b. 5 G.993.2 Profile 8c. 4 G.993.2 Profile 8d. 3 G.993.2 Profile 12a. 2 G.993.2 Profile 12b. 1 G.993.2 Profile 17a. 0 G.993.2 Profile 30a. Valid from: EDA 4.0
Status: current Access: read-write
OBJECT-TYPE    
  BITS profile30a(0), profile17a(1), profile12b(2), profile12a(3), profile8d(4), profile8c(5), profile8b(6), profile8a(7)  

miscVdslConfigStandardLimitMask 1.3.6.1.4.1.193.72.300.80.1.8.1.15
Proprietary interface for selecting a predefined standard compliant Bandplan & LimitMask. NOTE that selecting a predefined BandPlan & LimitMask overrides the vdslLineConfPhysVdslLimitingMaskDn/Up and the vdslLineConfPhysVdslBandPlanDn/Up parameters. To avoid this (e.g. for using a custom BandPlan and/or LimitMask), you should select the value here. Valid from: EDA 4.0
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER aNUS0(0), aEU32(1), aEU36(2), aEU40(3), aEU44(4), aEU48(5), aEU52(6), aEU56(7), aEU60(8), aEU64(9), b81(10), b82(11), b83(12), b84(13), b85(14), b86(15), b87(16), b88(17), b89(18), b810(19), b811(20), b71(21), b72(22), b73(23), b74(24), b75(25), b76(26), custom(255)  

vdslVtucProprietaryChanXTable 1.3.6.1.4.1.193.72.300.80.1.9
VDSL VTU-C Proprietary Channel Extension Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VdslVtucProprietaryChanXEntry

vdslVtucProprietaryChanXEntry 1.3.6.1.4.1.193.72.300.80.1.9.1
An entry in the vdslVtucProprietaryChanXEntry.
Status: current Access: not-accessible
OBJECT-TYPE    
  VdslVtucProprietaryChanXEntry  

vdslVtucProprietaryChanXI 1.3.6.1.4.1.193.72.300.80.1.9.1.1
I is the interleaver block length. Note: This parameter applies to VDSL2 protocols only.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslVtucProprietaryChanXG 1.3.6.1.4.1.193.72.300.80.1.9.1.2
G is the total number of overhead octets in an overhead superframe. Note: This parameter applies to VDSL2 protocols
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslVtucProprietaryChanXU 1.3.6.1.4.1.193.72.300.80.1.9.1.3
U is the total number of overhead subframes per overhead superframe. Note: This parameter applies to VDSL2 protocols only.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslVtucProprietaryChanXF 1.3.6.1.4.1.193.72.300.80.1.9.1.4
F is the number of overhead frames in the overhead superframe. Note: This parameter applies to VDSL2 protocols only.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslVtucProprietaryChanXTpsTcTypeB0 1.3.6.1.4.1.193.72.300.80.1.9.1.10
The TPC-TC currently used for bearer channel B0. The two channels must use the same TPS-TC configuration, if enabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER inactive(1), ptm(2), atm(4)  

vdslVtucProprietaryChanXTpsTcTypeB1 1.3.6.1.4.1.193.72.300.80.1.9.1.15
The TPC-TC currently used for bearer channel B1. The two channels must use the same TPS-TC configuration, if enabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER inactive(1), ptm(2), atm(4)  

vdslVturProprietaryChanXTable 1.3.6.1.4.1.193.72.300.80.1.10
VDSL VTU-R Proprietary Channel Extension Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VdslVturProprietaryChanXEntry

vdslVturProprietaryChanXEntry 1.3.6.1.4.1.193.72.300.80.1.10.1
An entry in the vdslVturProprietaryChanXTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VdslVturProprietaryChanXEntry  

vdslVturProprietaryChanXI 1.3.6.1.4.1.193.72.300.80.1.10.1.1
I is the interleaver block length. Note: This parameter applies to VDSL2 protocols only.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslVturProprietaryChanXG 1.3.6.1.4.1.193.72.300.80.1.10.1.2
G is the total number of overhead octets in an overhead superframe. Note: This parameter applies to VDSL2 protocols
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslVturProprietaryChanXU 1.3.6.1.4.1.193.72.300.80.1.10.1.3
U is the total number of overhead subframes per overhead superframe. Note: This parameter applies to VDSL2 protocols only.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslVturProprietaryChanXF 1.3.6.1.4.1.193.72.300.80.1.10.1.4
F is the number of overhead frames in the overhead superframe. Note: This parameter applies to VDSL2 protocols only.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLineStatusPhysVdslBandPlanDnTable 1.3.6.1.4.1.193.72.300.80.1.11
This table contains status information of the actual BandPlanDn
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VdslLineStatusPhysVdslBandPlanDnEntry

vdslLineStatusPhysVdslBandPlanDnEntry 1.3.6.1.4.1.193.72.300.80.1.11.1
An entry in vdslLineStatusPhysVdslBandPlanDnTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VdslLineStatusPhysVdslBandPlanDnEntry  

statusBandPlanDnNoOfToneGroups 1.3.6.1.4.1.193.72.300.80.1.11.1.1
Actual number of bands downstream
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..3  

statusBandPlanDnToneGroups0StartTone 1.3.6.1.4.1.193.72.300.80.1.11.1.2
Actual start tone for this band
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..4096  

statusBandPlanDnToneGroups0EndTone 1.3.6.1.4.1.193.72.300.80.1.11.1.3
Actual end tone for this band
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..4096  

statusBandPlanDnToneGroups1StartTone 1.3.6.1.4.1.193.72.300.80.1.11.1.4
Actual start tone for this statusBand
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..4096  

statusBandPlanDnToneGroups1EndTone 1.3.6.1.4.1.193.72.300.80.1.11.1.5
Actual end tone for this band
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..4096  

statusBandPlanDnToneGroups2StartTone 1.3.6.1.4.1.193.72.300.80.1.11.1.6
Actual start tone for this band
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..4096  

statusBandPlanDnToneGroups2EndTone 1.3.6.1.4.1.193.72.300.80.1.11.1.7
Actual end tone for this band
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..4096  

vdslLineStatusPhysVdslBandPlanUpTable 1.3.6.1.4.1.193.72.300.80.1.12
This table contains status information of the actual BandPlanUp
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VdslLineStatusPhysVdslBandPlanUpEntry

vdslLineStatusPhysVdslBandPlanUpEntry 1.3.6.1.4.1.193.72.300.80.1.12.1
An entry in vdslLineStatusPhysVdslBandPlanUpTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VdslLineStatusPhysVdslBandPlanUpEntry  

statusBandPlanUpNoOfToneGroups 1.3.6.1.4.1.193.72.300.80.1.12.1.1
Actual number of bands downstream
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..3  

statusBandPlanUpToneGroups0StartTone 1.3.6.1.4.1.193.72.300.80.1.12.1.2
Actual start tone for this band
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..4096  

statusBandPlanUpToneGroups0EndTone 1.3.6.1.4.1.193.72.300.80.1.12.1.3
Actual end tone for this band
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..4096  

statusBandPlanUpToneGroups1StartTone 1.3.6.1.4.1.193.72.300.80.1.12.1.4
Actual start tone for this band
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..4096  

statusBandPlanUpToneGroups1EndTone 1.3.6.1.4.1.193.72.300.80.1.12.1.5
Actual end tone for this band
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..4096  

statusBandPlanUpToneGroups2StartTone 1.3.6.1.4.1.193.72.300.80.1.12.1.6
Actual start tone for this band
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..4096  

statusBandPlanUpToneGroups2EndTone 1.3.6.1.4.1.193.72.300.80.1.12.1.7
Actual end tone for this band
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..4096  

vdslLineConfPhysVdslPboPsdDnTable 1.3.6.1.4.1.193.72.300.80.1.20
This table provides a set of line configuration parameters to generate a modified downstream PSD mask for Downstream Power Back-Off - Shaped (DPBOSHAPED). The implementation is according to G.997.1 (third revision) section 7.3.1.2.13. The parameters will be substituted by XDSL2 Line MIB parameters.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VdslLineConfPhysVdslPboPsdDnEntry

vdslLineConfPhysVdslPboPsdDnEntry 1.3.6.1.4.1.193.72.300.80.1.20.1
An entry in vdslLineConfPhysVdslPboPsdDnTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VdslLineConfPhysVdslPboPsdDnEntry  

vdslLineConfPhysVdslPboPsdDnEsel 1.3.6.1.4.1.193.72.300.80.1.20.1.5
This configuration parameter defines the assumed electrical length of cables (E-side cables) connecting exchange based DSL services to a remote flexibility point (cabinet), that hosts the xTU-C that is subject to spectrally shaped downstream power back-off depending on this length. For this parameter the electrical length is defined as the loss (in dB) of an equivalent length of hypothetical cable at a reference frequency defined by the network operator or in spectrum management regulations. DPBOESEL shall be coded as an unsigned integer representing an electrical length from 0 dB to 255.5 dB in steps of 0.5 dB. All values in the range are valid. If DPBOESEL is set to zero, the DPBO in this section shall be disabled. G.997.1 name: DPBOESEL. Valid from: EDA 4.0
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..511  

vdslLineConfPhysVdslPboPsdDnEscmA 1.3.6.1.4.1.193.72.300.80.1.20.1.10
This configuration parameter is used to define a cable model in terms of three scalars DPBOESCMA, DPBOESCMB and DPBOESCMC that shall be used to describe the frequency dependent loss of E-side cables. Parameters DPBOESCMA, DPBOESCMB, DPBOESCMC shall be coded as unsigned integers representing a scalar value from -1 to 1.5 in steps of 1/256. All values in the range are valid. G.997.1 name: DPBOESCMA. Valid from: EDA 4.0
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..640  

vdslLineConfPhysVdslPboPsdDnEscmB 1.3.6.1.4.1.193.72.300.80.1.20.1.15
This configuration parameter is used to define a cable model in terms of three scalars DPBOESCMA, DPBOESCMB and DPBOESCMC that shall be used to describe the frequency dependent loss of E-side cables. Parameters DPBOESCMA, DPBOESCMB, DPBOESCMC shall be coded as unsigned integers representing a scalar value from -1 to 1.5 in steps of 1/256. All values in the range are valid. G.997.1 name: DPBOESCMB. Valid from: EDA 4.0
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..640  

vdslLineConfPhysVdslPboPsdDnEscmC 1.3.6.1.4.1.193.72.300.80.1.20.1.20
This configuration parameter is used to define a cable model in terms of three scalars DPBOESCMA, DPBOESCMB and DPBOESCMC that shall be used to describe the frequency dependent loss of E-side cables. Parameters DPBOESCMA, DPBOESCMB, DPBOESCMC shall be coded as unsigned integers representing a scalar value from -1 to 1.5 in steps of 1/256. All values in the range are valid. G.997.1 name: DPBOESCMC. Valid from: EDA 4.0
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..640  

vdslLineConfPhysVdslPboPsdDnFmin 1.3.6.1.4.1.193.72.300.80.1.20.1.25
Defines the minimum frequency from which the DPBO shall be applied. It ranges from 0 kHz to 8832 kHz in steps of 4.3125 kHz. G.997.1 name: DPBOFMIN. Valid from: EDA 4.0
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..2048  

vdslLineConfPhysVdslPboPsdDnFmax 1.3.6.1.4.1.193.72.300.80.1.20.1.30
Defines the maximum frequency at which DPBO may be applied. It ranges from 138 kHz to 29997.75 kHz in steps of 4.3125 kHz. G.997.1 name: DPBOFMAX. Valid from: EDA 4.0
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 32..6956  

vdslLineConfPhysVdslPboPsdDnMus 1.3.6.1.4.1.193.72.300.80.1.20.1.35
Defines the assumed Minimum Usable receive PSD mask (in dBm/Hz) for exchange based services, used to modify parameter DPBOFMAX. It shall be coded as an integer representing a PSD mask level from -127.5 dBm/Hz to 0 dBm/Hz in steps of 0.5 dB. All values in the range are valid. NOTE - The PSD mask level is 3.5 dB above the signal PSD level G.997.1 name: DPBOFMUS. Valid from: EDA 4.0
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER -255..0  

vdslLineConfPhysVdslPboPsdDnAdvanced 1.3.6.1.4.1.193.72.300.80.1.20.1.40
Enables an alternative downstream Power Back-Off, which differs from the standard G.997.1 PBO calculation.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

vdslLineConfPhysVdslPboPsdDnEselMin 1.3.6.1.4.1.193.72.300.80.1.20.1.45
This configuration parameter defines the minimum value of all trunk line losses of the cable distributors served (including the KVz at the DSLAM site). This parameter is not G.997.1 compliant and has only effect when vdslLineConfPhysVdslPboPsdDnAdvanced is enabled. Valid from: EDA 4.0
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..511  

vdslLineConfPhysVdslMibMaskDsTable 1.3.6.1.4.1.193.72.300.80.1.25
This table contains information of MibMaskDs configuration in accordance with to G.997.1 section 7.3.1.2.9
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VdslLineConfPhysVdslMibMaskDsEntry

vdslLineConfPhysVdslMibMaskDsEntry 1.3.6.1.4.1.193.72.300.80.1.25.1
An entry in vdslLineConfPhysVdslMibMaskDsTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VdslLineConfPhysVdslMibMaskDsEntry  

mibMaskDsNoOfBreakPoints 1.3.6.1.4.1.193.72.300.80.1.25.1.5
Number of breakpoints in downstream mask. Each breakpoint is defined by a subcarrier index (mibMaskDsBpToneIndex) and a PSD level (mibMaskDsBpPsd). G.997.1 name: PSDMASKds. Valid from: EDA 4.0
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..32  

mibMaskDsBpToneIndex 1.3.6.1.4.1.193.72.300.80.1.25.1.10
Toneindexes for 32 breakpoints. Each ToneIndex is 2 octets. The octet string has the format: [Bp0_Hi, Bp0_Low....Bp31_Hi, Bp31_Low] Valid range is [0, 4096]. G.997.1 name: PSDMASKds. Valid from: EDA 4.0
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(64)  

mibMaskDsBpPsd 1.3.6.1.4.1.193.72.300.80.1.25.1.15
PSD level in 0.1 dBm/Hz for 32 breakpoints. Each BpPsd has to octets. The octet string has the format: [Bp0_Hi, Bp0_Low....Bp31_Hi, Bp31_Low] Valid range is [0,-96] dBm/Hz. G.997.1 name: PSDMASKds. Valid from: EDA 4.0
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(64)  

vdslLineConfPhysVdslMibMaskUsTable 1.3.6.1.4.1.193.72.300.80.1.30
This table contains information of MibMaskUs configuration in accordance with to G.997.1 section 7.3.1.2.12
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VdslLineConfPhysVdslMibMaskUsEntry

vdslLineConfPhysVdslMibMaskUsEntry 1.3.6.1.4.1.193.72.300.80.1.30.1
An entry in vdslLineConfPhysVdslMibMaskUsTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VdslLineConfPhysVdslMibMaskUsEntry  

mibMaskUsNoOfBreakPoints 1.3.6.1.4.1.193.72.300.80.1.30.1.5
Number of breakpoints in upstream mask. Each breakpoint is defined by a subcarrier index (mibMaskUsBpToneIndex) and a PSD level (mibMaskUsBpPsd). G.997.1 name: PSDMASKus. Valid from: EDA 4.0
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..16  

mibMaskUsBpToneIndex 1.3.6.1.4.1.193.72.300.80.1.30.1.10
Toneindexes for 16 breakpoints. Each ToneIndex is 2 octets. The octet string has the format: [Bp0_Hi, Bp0_Low....Bp15_Hi, Bp15_Low] Valid range is [0, 4096]. G.997.1 name: PSDMASKus. Valid from: EDA 4.0
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(32)  

mibMaskUsBpPsd 1.3.6.1.4.1.193.72.300.80.1.30.1.15
PSD level in 0.1 dBm/Hz for 16 breakpoints. Each BpPsd has to octets. The octet string has the format: [Bp0_Hi, Bp0_Low....Bp15_Hi, Bp15_Low] Valid range is [0,-96] dBm/Hz. G.997.1 name: PSDMASKus. Valid from: EDA 4.0
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(32)  

vdslProprietaryLineConfProfileXTable 1.3.6.1.4.1.193.72.300.80.1.35
VDSL Proprietary Line Configuration Profile Extention Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VdslProprietaryLineConfProfileXEntry

vdslProprietaryLineConfProfileXEntry 1.3.6.1.4.1.193.72.300.80.1.35.1
An entry in the vdslLineConfProfileXTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VdslProprietaryLineConfProfileXEntry  

vdslVtucProprietaryConfXTpsTcType 1.3.6.1.4.1.193.72.300.80.1.35.1.5
Configure allowed traffic type: ATM, PTM or both.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER atm(2), ptm(4), both(6)  

vdslVtucProprietaryConfXPreemtionAllowedB0 1.3.6.1.4.1.193.72.300.80.1.35.1.10
If True the subscriber is allowed to send preemptive traffic frames on bearer channel B0. The value can be either True(1) or False(2).
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

vdslVtucProprietaryConfXPreemtionAllowedB1 1.3.6.1.4.1.193.72.300.80.1.35.1.15
If True the subscriber is allowed to send preemptive traffic frames on bearer channel B1. The value can be either True(1) or False(2).
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

vdslVtucChanIntervalXTable 1.3.6.1.4.1.193.72.300.80.1.40
This table provides extra information in relation to the xdslXtucChanIntervalTable for each VTU-C channel's performance collection interval. XDSL channel interfaces are those ifEntries where ifType is equal to Interleave(124) or Fast(125). Performance Data Interval number 1 is the the most recent previous interval; interval 96 is 24 hours ago. Intervals 2..96 are optional. Interval number 1 is the only interval used currently.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VdslVtucChanIntervalXEntry

vdslVtucChanIntervalXEntry 1.3.6.1.4.1.193.72.300.80.1.40.1
An entry in the vdslVtucChanIntervalXTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VdslVtucChanIntervalXEntry  

vdslVtucChanIntervalXPtmCrcErrors 1.3.6.1.4.1.193.72.300.80.1.40.1.5
Count of all PTM CRC errors on PTM non-preemtive traffic received on this channel during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  PerfIntervalCount  

vdslVtucChanIntervalXPtmCrcErrorsP 1.3.6.1.4.1.193.72.300.80.1.40.1.10
Count of all PTM CRC errors on PTM preemtive traffic received on this channel during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  PerfIntervalCount  

vdslVtucChanIntervalXPtmCv 1.3.6.1.4.1.193.72.300.80.1.40.1.15
Count of all PTM Coding violations on PTM non-preemtive traffic received on this channel during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  PerfIntervalCount  

vdslVtucChanIntervalXPtmCvP 1.3.6.1.4.1.193.72.300.80.1.40.1.20
Count of all PTM Coding violations on PTM preemtive traffic received on this channel during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  PerfIntervalCount  

vdslVturChanIntervalXTable 1.3.6.1.4.1.193.72.300.80.1.45
This table provides extra information in relation to the xdslXturChanIntervalTable for each VTU-R channel's performance collection interval. XDSL channel interfaces are those ifEntries where ifType is equal to Interleave(124) or Fast(125). Performance Data Interval number 1 is the the most recent previous interval; interval 96 is 24 hours ago. Intervals 2..96 are optional. Interval number 1 is the only interval used currently.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VdslVturChanIntervalXEntry

vdslVturChanIntervalXEntry 1.3.6.1.4.1.193.72.300.80.1.45.1
An entry in the vdslVturChanIntervalXTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VdslVturChanIntervalXEntry  

vdslVturChanIntervalXPtmCrcErrors 1.3.6.1.4.1.193.72.300.80.1.45.1.5
Count of all PTM CRC errors on PTM non-preemtive traffic received on this channel during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  PerfIntervalCount  

vdslVturChanIntervalXPtmCrcErrorsP 1.3.6.1.4.1.193.72.300.80.1.45.1.10
Count of all PTM CRC errors on PTM preemtive traffic received on this channel during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  PerfIntervalCount  

vdslVturChanIntervalXPtmCv 1.3.6.1.4.1.193.72.300.80.1.45.1.15
Count of all PTM Coding violations on PTM non-preemtive traffic received on this channel during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  PerfIntervalCount  

vdslVturChanIntervalXPtmCvP 1.3.6.1.4.1.193.72.300.80.1.45.1.20
Count of all PTM Coding violations on PTM preemtive traffic received on this channel during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  PerfIntervalCount  

vdslVtucChanPerfDataXTable 1.3.6.1.4.1.193.72.300.80.1.50
This table provides extra VTU-C channel information in relation to the adslAtucChanPerfDataTable. VDSL2 channel interfaces are those ifEntries where ifType is equal to Interleave(124) or Fast(125).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VdslVtucChanPerfDataXEntry

vdslVtucChanPerfDataXEntry 1.3.6.1.4.1.193.72.300.80.1.50.1
An entry in the vdslVtucChanPerfDataXTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VdslVtucChanPerfDataXEntry  

vdslVtucChanIntervalXCurr15MinPtmCrcErrors 1.3.6.1.4.1.193.72.300.80.1.50.1.5
Count of all PTM CRC errors on PTM non-preemtive traffic received on this channel within the current 15 minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  PerfCurrentCount  

vdslVtucChanIntervalXCurr1DayPtmCrcErrors 1.3.6.1.4.1.193.72.300.80.1.50.1.10
Count of all PTM CRC errors on PTM non-preemtive traffic received on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed.
Status: current Access: read-only
OBJECT-TYPE    
  AdslPerfCurrDayCount  

vdslVtucChanIntervalXPrev1DayPtmCrcErrors 1.3.6.1.4.1.193.72.300.80.1.50.1.15
Count of all PTM CRC errors on PTM non-preemtive traffic blocks received on this channel within the most recent previous 1-day period.
Status: current Access: read-only
OBJECT-TYPE    
  AdslPerfPrevDayCount  

vdslVtucChanIntervalXCurr15MinPtmCrcErrorsP 1.3.6.1.4.1.193.72.300.80.1.50.1.20
Count of all PTM CRC errors on PTM preemtive traffic received on this channel within the current 15 minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  PerfCurrentCount  

vdslVtucChanIntervalXCurr1DayPtmCrcErrorsP 1.3.6.1.4.1.193.72.300.80.1.50.1.25
Count of all PTM CRC errors on PTM preemtive traffic received on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed.
Status: current Access: read-only
OBJECT-TYPE    
  AdslPerfCurrDayCount  

vdslVtucChanIntervalXPrev1DayPtmCrcErrorsP 1.3.6.1.4.1.193.72.300.80.1.50.1.30
Count of all PTM CRC errors on PTM preemtive traffic blocks received on this channel within the most recent previous 1-day period.
Status: current Access: read-only
OBJECT-TYPE    
  AdslPerfPrevDayCount  

vdslVtucChanIntervalXCurr15MinPtmCv 1.3.6.1.4.1.193.72.300.80.1.50.1.35
Count of all PTM Coding violations on PTM non-preemtive received on this channel within the current 15 minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  PerfCurrentCount  

vdslVtucChanIntervalXCurr1DayPtmCv 1.3.6.1.4.1.193.72.300.80.1.50.1.40
Count of all PTM Coding violations on PTM non-preemtive received on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed.
Status: current Access: read-only
OBJECT-TYPE    
  AdslPerfCurrDayCount  

vdslVtucChanIntervalXPrev1DayPtmCv 1.3.6.1.4.1.193.72.300.80.1.50.1.45
Count of all PTM Coding violations on PTM non-preemtive blocks received on this channel within the most recent previous 1-day period.
Status: current Access: read-only
OBJECT-TYPE    
  AdslPerfPrevDayCount  

vdslVtucChanIntervalXCurr15MinPtmCvP 1.3.6.1.4.1.193.72.300.80.1.50.1.50
Count of all PTM Coding violations on PTM preemtive received on this channel within the current 15 minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  PerfCurrentCount  

vdslVtucChanIntervalXCurr1DayPtmCvP 1.3.6.1.4.1.193.72.300.80.1.50.1.55
Count of all PTM Coding violations on PTM preemtive received on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed.
Status: current Access: read-only
OBJECT-TYPE    
  AdslPerfCurrDayCount  

vdslVtucChanIntervalXPrev1DayPtmCvP 1.3.6.1.4.1.193.72.300.80.1.50.1.60
Count of all PTM Coding violations on PTM preemtive blocks received on this channel within the most recent previous 1-day period.
Status: current Access: read-only
OBJECT-TYPE    
  AdslPerfPrevDayCount  

vdslVturChanPerfDataXTable 1.3.6.1.4.1.193.72.300.80.1.55
This table provides extra VTU-R channel information in relation to the adslAtucChanPerfDataTable. VDSL2 channel interfaces are those ifEntries where ifType is equal to Interleave(124) or Fast(125).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VdslVturChanPerfDataXEntry

vdslVturChanPerfDataXEntry 1.3.6.1.4.1.193.72.300.80.1.55.1
An entry in the vdslVturChanPerfDataXTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VdslVturChanPerfDataXEntry  

vdslVturChanIntervalXCurr15MinPtmCrcErrors 1.3.6.1.4.1.193.72.300.80.1.55.1.5
Count of all PTM CRC errors on PTM non-preemtive traffic received on this channel within the current 15 minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  PerfCurrentCount  

vdslVturChanIntervalXCurr1DayPtmCrcErrors 1.3.6.1.4.1.193.72.300.80.1.55.1.10
Count of all PTM CRC errors on PTM non-preemtive traffic received on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed.
Status: current Access: read-only
OBJECT-TYPE    
  AdslPerfCurrDayCount  

vdslVturChanIntervalXPrev1DayPtmCrcErrors 1.3.6.1.4.1.193.72.300.80.1.55.1.15
Count of all PTM CRC errors on PTM non-preemtive traffic blocks received on this channel within the most recent previous 1-day period.
Status: current Access: read-only
OBJECT-TYPE    
  AdslPerfPrevDayCount  

vdslVturChanIntervalXCurr15MinPtmCrcErrorsP 1.3.6.1.4.1.193.72.300.80.1.55.1.20
Count of all PTM CRC errors on PTM preemtive traffic received on this channel within the current 15 minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  PerfCurrentCount  

vdslVturChanIntervalXCurr1DayPtmCrcErrorsP 1.3.6.1.4.1.193.72.300.80.1.55.1.25
Count of all PTM CRC errors on PTM preemtive traffic received on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed.
Status: current Access: read-only
OBJECT-TYPE    
  AdslPerfCurrDayCount  

vdslVturChanIntervalXPrev1DayPtmCrcErrorsP 1.3.6.1.4.1.193.72.300.80.1.55.1.30
Count of all PTM CRC errors on PTM preemtive traffic blocks received on this channel within the most recent previous 1-day period.
Status: current Access: read-only
OBJECT-TYPE    
  AdslPerfPrevDayCount  

vdslVturChanIntervalXCurr15MinPtmCv 1.3.6.1.4.1.193.72.300.80.1.55.1.35
Count of all PTM Coding violations on PTM non-preemtive received on this channel within the current 15 minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  PerfCurrentCount  

vdslVturChanIntervalXCurr1DayPtmCv 1.3.6.1.4.1.193.72.300.80.1.55.1.40
Count of all PTM Coding violations on PTM non-preemtive received on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed.
Status: current Access: read-only
OBJECT-TYPE    
  AdslPerfCurrDayCount  

vdslVturChanIntervalXPrev1DayPtmCv 1.3.6.1.4.1.193.72.300.80.1.55.1.45
Count of all PTM Coding violations on PTM non-preemtive blocks received on this channel within the most recent previous 1-day period.
Status: current Access: read-only
OBJECT-TYPE    
  AdslPerfPrevDayCount  

vdslVturChanIntervalXCurr15MinPtmCvP 1.3.6.1.4.1.193.72.300.80.1.55.1.50
Count of all PTM Coding violations on PTM preemtive received on this channel within the current 15 minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  PerfCurrentCount  

vdslVturChanIntervalXCurr1DayPtmCvP 1.3.6.1.4.1.193.72.300.80.1.55.1.55
Count of all PTM Coding violations on PTM preemtive received on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed.
Status: current Access: read-only
OBJECT-TYPE    
  AdslPerfCurrDayCount  

vdslVturChanIntervalXPrev1DayPtmCvP 1.3.6.1.4.1.193.72.300.80.1.55.1.60
Count of all PTM Coding violations on PTM preemtive blocks received on this channel within the most recent previous 1-day period.
Status: current Access: read-only
OBJECT-TYPE    
  AdslPerfPrevDayCount  

vdsl2SCStatusTable 1.3.6.1.4.1.193.72.300.80.2.5
The table vdsl2SCStatusTable contains status parameters of VDSL2/ADSL/ADSL2 and ADSL2+ sub-carriers. This table contains live data from equipment. This table is copied from draft-ietf-adslmib-vdsl2-01.txt, to secure a smooth migration to the VDSL2-LINE MIB when this MIB is approved.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Vdsl2SCStatusEntry

vdsl2SCStatusEntry 1.3.6.1.4.1.193.72.300.80.2.5.1
The table Hfvdsl2SCStatusEntry contains status parameters of VDSL2/ADSL/ADSL2 and ADSL2+ sub-carriers. One index of this table is an interface index where the interface has an ifType of vdsl2(xxx). A second index of this table is the transmission direction. A third index identifies the specific segment of the sub-carriers status addressed.
Status: current Access: not-accessible
OBJECT-TYPE    
  Vdsl2SCStatusEntry  

vdsl2SCStatusDirection 1.3.6.1.4.1.193.72.300.80.2.5.1.1
The direction of the sub-carrier either upstream or downstream
Status: current Access: not-accessible
OBJECT-TYPE    
  Vdsl2Direction  

vdsl2SCStatusSegment 1.3.6.1.4.1.193.72.300.80.2.5.1.2
The segment of the sub-carriers status information provided by this row. Several status parameters in this table are retrieved in segments. The first segment of the status information is retrieved with vdsl2SCStatusSegment=1, the second segment is retrieved with vdsl2SCStatusSegment=2, and so on. When any status parameter is retrieved in n segments where n<8) then, for that parameter, GET operations for the rest segment numbers (n+1 to 8) are responded with a value that indicates: No measurement could be done. This table is from draft-ietf-adslmib-vdsl2-01.txt.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..8  

vdsl2SCStatusSnr 1.3.6.1.4.1.193.72.300.80.2.5.1.5
The SNR Margin per sub-carrier group, expressing the ratio between the received signal power and received noise power per sub-scriber group. It is an array of 512 octets, designed for supporting up to 512 (downstream) sub-carriers groups and can be retrieved in a single segment. The number of utilized octets on downstream direction depends on NSds, and on upstream direction it depends on NSus. This value is referred here as NS. Octet i (0 <= i < NS) is set to a value in the range 0 to 254 to indicate that the respective downstream or upstream sub- carrier group i has SNR of: (-32 + Xdsl2SubcarrierSnr(i)/2) in dB (i.e., -32 to 95dB). The special value 255 means that no measurement could be done for the sub-carrier group because it is out of the PSD mask passband or that the noise PSD is out of range to be represented. Each value in this array is 8 bits wide. This table is from draft-ietf-adslmib-vdsl2-01.txt.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..512)  

vdsl2SCStatusBitsAlloc 1.3.6.1.4.1.193.72.300.80.2.5.1.10
The bits allocation per sub-carrier. An array of 256 octets (512 nibbles), designed for supporting up to 512 (downstream) sub-carriers. When more then 512 sub-carriers are supported, the status information is reported through multiple (up to 8) segments. The first segment is then used for the first 512 sub-carriers. The second segment is used for the sub-carriers 512 to 1023 and so on. The aggregate number of utilized nibbles on downstream direction (in all segments) depends on NSds, and on upstream direction it depends on NSus. This value is referred here as NS. The segment number is in vdsl2SCStatusSegment. Nibble i (0 <= i < MIN(NS-(segment-1)*512,512)) in each segment is set to a value in the range 0 to 15 to indicate that the respective downstream or upstream sub-carrier j (j=(segement-1)*512+i) has the same amount of bits allocation. This table is from draft-ietf-adslmib-vdsl2-01.txt.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..256)  

vdsl2SCStatusGainAlloc 1.3.6.1.4.1.193.72.300.80.2.5.1.15
The gain allocation per sub-carrier. An array of 512 16-bits values, designed for supporting up to 512 (downstream) sub- carriers. When more then 512 sub-carriers are supported, the status information is reported through multiple (up to 8) segments. The first segment is then used for the first 512 sub-carriers. The second segment is used for the sub-carriers 512 to 1023 and so on. The aggregate number of utilized octets on downstream direction depends on NSds, and on upstream direction it depends on NSus. This value is referred here as NS. The segment number is in vdsl2SCStatusSegment. Value i (0 <= i < MIN(NS-(segment-1)*512,512)) in each segment is set to a value in the range 0 to 4093 to indicate that the respective downstream or upstream sub-carrier j (j=(segement-1)*512+i) has the same amount of gain value. The gain value is represented as a multiple of 1/512 on linear scale. Each value in this array is 16 bits wide and is stored in big endian format. This table is from draft-ietf-adslmib-vdsl2-01.txt.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..1024)  

vdsl2ChConfProfileTable 1.3.6.1.4.1.193.72.300.80.3.1
The table vdsl2ChConfProfileTable contains DSL channel profile configuration. Entries in this table MUST be maintained in a persistent manner. This table is copied from draft-ietf-adslmib-vdsl2-01.txt, to secure a smooth migration to the VDSL2-LINE MIB when this MIB is approved.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Vdsl2ChConfProfileEntry

vdsl2ChConfProfileEntry 1.3.6.1.4.1.193.72.300.80.3.1.1
The table vdsl2ChConfProfileTable contains DSL channel profile configuration. A default profile with an index of 'DEFVAL' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document
Status: current Access: not-accessible
OBJECT-TYPE    
  Vdsl2ChConfProfileEntry  

vdsl2ChConfProfProfileName 1.3.6.1.4.1.193.72.300.80.3.1.1.1
This object identifies a row in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SnmpAdminString Size(1..32)  

vdsl2ChConfProfMinResDataRateDs 1.3.6.1.4.1.193.72.300.80.3.1.1.4
Minimum Reserved Data Rate on Downstream direction. The minimum reserved net data rate for the bearer channel, coded in bit/s. This parameter is used only if the Rate Adaptation Mode in the direction of the bearer channel (i.e., Xdsl2LineConfRaModeDs) is set to dynamicRa. This table is from draft-ietf-adslmib-vdsl2-01.txt.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..200000000  

vdsl2ChConfProfMinResDataRateUs 1.3.6.1.4.1.193.72.300.80.3.1.1.5
Minimum Reserved Data Rate on Upstream direction. The minimum reserved net data rate for the bearer channel, coded in bit/s. This parameter is used only if the Rate Adaptation Mode in the direction of the bearer channel (i.e., Xdsl2LineConfRaModeUs) is set to dynamicRa. This table is from draft-ietf-adslmib-vdsl2-01.txt.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..200000000  

vdslLineMiscPhysStatusTable 1.3.6.1.4.1.193.72.300.80.1.60
This table contains information of MiscVdslConf configuration
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VdslLineMiscPhysStatusEntry

vdslLineMiscPhysStatusEntry 1.3.6.1.4.1.193.72.300.80.1.60.1
An entry in vdslLineMiscPhysStatusTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VdslLineMiscPhysStatusEntry  

miscPhysStatusVdslProfileBitmap 1.3.6.1.4.1.193.72.300.80.1.60.1.5
VDSL2 profiles to be allowed by the near-end xTU on this line. It is coded in a bit map representation (0 if not allowed, 1 if allowed) as defined in G.997.1 (third revision), section 7.3.1.1.11: NOTE that profile 30a is not supported in EDA. BIT PROFILE 7 G.993.2 Profile 8a. 6 G.993.2 Profile 8b. 5 G.993.2 Profile 8c. 4 G.993.2 Profile 8d. 3 G.993.2 Profile 12a. 2 G.993.2 Profile 12b. 1 G.993.2 Profile 17a. 0 G.993.2 Profile 30a. Valid from: EDA 4.0
Status: current Access: read-only
OBJECT-TYPE    
  BITS profile30a(0), profile17a(1), profile12b(2), profile12a(3), profile8d(4), profile8c(5), profile8b(6), profile8a(7)  

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor