OC-STB-HOST-MIB

File: OC-STB-HOST-MIB.mib (115925 bytes)

Imported modules

DOCS-IF-MIB SNMPv2-CONF SNMPv2-SMI
SNMPv2-TC SNMP-FRAMEWORK-MIB INET-ADDRESS-MIB
HOST-RESOURCES-MIB CLAB-DEF-MIB

Imported symbols

TenthdB TenthdBmV OBJECT-GROUP
MODULE-COMPLIANCE Integer32 Unsigned32
Counter32 TimeTicks OBJECT-TYPE
MODULE-IDENTITY OBJECT-IDENTITY AutonomousType
DisplayString TruthValue RowPointer
TimeStamp PhysAddress MacAddress
TEXTUAL-CONVENTION SnmpAdminString InetAddressType
InetAddress hrDeviceIndex clabProjOpenCable

Defined Types

VideoOutputFormat  
Defines the output format of the video signal horizontal and vertical resolution.
TEXTUAL-CONVENTION    
  INTEGER format480i(1), format480p(2), format720p(3), format1080i(4), format1080p(5)  

AudioOutputFormat  
Defines the output format of the audio signal.
TEXTUAL-CONVENTION    
  INTEGER other(1), lpcm(2), ac3(3), eac3(4), mpeg1L1L2(5), mpeg1L3(6), mpeg2(7), mpeg4(8), dts(9), atrac(10)  

VideoAspectRatio  
Defines the horizontal and vertical aspect ratio of the video signal. 'fourByThree' means a 4 by 3 aspect ratio. 'sixteenByNine' means a 16 by 9 aspect ratio. 'other' indicates a non-specified aspect ratio.
TEXTUAL-CONVENTION    
  INTEGER other(1), fourByThree(2), sixteenByNine(3)  

OcStbHostAVInterfaceEntry  
SEQUENCE    
  ocStbHostAVInterfaceIndex Unsigned32
  ocStbHostAVInterfaceType AutonomousType
  ocStbHostAVInterfaceDesc SnmpAdminString
  ocStbHostAVInterfaceStatus INTEGER

OcStbHostIEEE1394Entry  
SEQUENCE    
  ocStbHostIEEE1394ActiveNodes Integer32
  ocStbHostIEEE1394DataXMission TruthValue
  ocStbHostIEEE1394DTCPStatus TruthValue
  ocStbHostIEEE1394LoopStatus TruthValue
  ocStbHostIEEE1394RootStatus TruthValue
  ocStbHostIEEE1394CycleIsMaster TruthValue
  ocStbHostIEEE1394IRMStatus TruthValue
  ocStbHostIEEE1394AudioMuteStatus TruthValue
  ocStbHostIEEE1394VideoMuteStatus TruthValue

OcStbHostIEEE1394ConnectedDevicesEntry  
SEQUENCE    
  ocStbHostIEEE1394ConnectedDevicesIndex Unsigned32
  ocStbHostIEEE1394ConnectedDevicesAVInterfaceIndex Unsigned32
  ocStbHostIEEE1394ConnectedDevicesSubUnitType INTEGER
  ocStbHostIEEE1394ConnectedDevicesEui64 OCTET STRING
  ocStbHostIEEE1394ConnectedDevicesADSourceSelectSupport TruthValue

OcStbHostDVIHDMIEntry  
SEQUENCE    
  ocStbHostDVIHDMIOutputType INTEGER
  ocStbHostDVIHDMIConnectionStatus TruthValue
  ocStbHostDVIHDMIRepeaterStatus TruthValue
  ocStbHostDVIHDMIVideoXmissionStatus TruthValue
  ocStbHostDVIHDMIHDCPStatus TruthValue
  ocStbHostDVIHDMIVideoMuteStatus TruthValue
  ocStbHostDVIHDMIOutputFormat VideoOutputFormat
  ocStbHostDVIHDMIAspectRatio VideoAspectRatio
  ocStbHostDVIHDMIHostDeviceHDCPStatus INTEGER
  ocStbHostDVIHDMIAudioFormat AudioOutputFormat
  ocStbHostDVIHDMIAudioSampleRate INTEGER
  ocStbHostDVIHDMIAudioChannelCount Unsigned32
  ocStbHostDVIHDMIAudioMuteStatus TruthValue

OcStbHostComponentVideoEntry  
SEQUENCE    
  ocStbHostComponentVideoConstrainedStatus TruthValue
  ocStbHostComponentOutputFormat VideoOutputFormat
  ocStbHostComponentAspectRatio VideoAspectRatio
  ocStbHostComponentVideoMuteStatus TruthValue

OcStbHostRFChannelOutEntry  
SEQUENCE    
  ocStbHostRFChannelOut Unsigned32
  ocStbHostRFChannelOutAudioMuteStatus TruthValue
  ocStbHostRFChannelOutVideoMuteStatus TruthValue

OcStbHostSPDIfEntry  
SEQUENCE    
  ocStbHostSPDIfAudioFormat AudioOutputFormat
  ocStbHostSPDIfAudioMuteStatus TruthValue

OcStbHostInBandTunerEntry  
SEQUENCE    
  ocStbHostInBandTunerModulationMode INTEGER
  ocStbHostInBandTunerFrequency Unsigned32
  ocStbHostInBandTunerInterleaver INTEGER
  ocStbHostInBandTunerPower TenthdBmV
  ocStbHostInBandTunerAGCValue Unsigned32
  ocStbHostInBandTunerSNRValue TenthdB
  ocStbHostInBandTunerUnerroreds Counter32
  ocStbHostInBandTunerCorrecteds Counter32
  ocStbHostInBandTunerUncorrectables Counter32
  ocStbHostInBandTunerCarrierLockLost Counter32
  ocStbHostInBandTunerPCRErrors Counter32
  ocStbHostInBandTunerPTSErrors Counter32
  ocStbHostInBandTunerState INTEGER
  ocStbHostInBandTunerBER INTEGER
  ocStbHostInBandTunerSecsSinceLock Unsigned32
  ocStbHostInBandTunerEqGain Integer32
  ocStbHostInBandTunerMainTapCoeff INTEGER

OcStbHostProgramStatusEntry  
SEQUENCE    
  ocStbHostProgramIndex Unsigned32
  ocStbHostProgramAVSource RowPointer
  ocStbHostProgramAVDestination RowPointer
  ocStbHostProgramContentSource RowPointer
  ocStbHostProgramContentDestination RowPointer

OcStbHostMpeg2ContentEntry  
SEQUENCE    
  ocStbHostMpeg2ContentIndex Unsigned32
  ocStbHostMpeg2ContentProgramNumber Unsigned32
  ocStbHostMpeg2ContentTransportStreamID Unsigned32
  ocStbHostMpeg2ContentTotalStreams Unsigned32
  ocStbHostMpeg2ContentSelectedVideoPID Integer32
  ocStbHostMpeg2ContentSelectedAudioPID Integer32
  ocStbHostMpeg2ContentOtherAudioPIDs TruthValue
  ocStbHostMpeg2ContentCCIValue INTEGER
  ocStbHostMpeg2ContentAPSValue INTEGER
  ocStbHostMpeg2ContentCITStatus TruthValue
  ocStbHostMpeg2ContentBroadcastFlagStatus TruthValue
  ocStbHostMpeg2ContentEPNStatus TruthValue
  ocStbHostMpeg2ContentPCRPID Integer32
  ocStbHostMpeg2ContentPCRLockStatus INTEGER
  ocStbHostMpeg2ContentDecoderPTS Integer32
  ocStbHostMpeg2ContentDiscontinuities Counter32
  ocStbHostMpeg2ContentPktErrors Counter32
  ocStbHostMpeg2ContentPipelineErrors Counter32
  ocStbHostMpeg2ContentDecoderRestarts Counter32

OcStbHostAnalogVideoEntry  
SEQUENCE    
  ocStbHostAnalogVideoProtectionStatus INTEGER

OcStbHostSoftwareApplicationInfoEntry  
SEQUENCE    
  ocStbHostSoftwareApplicationInfoIndex Unsigned32
  ocStbHostSoftwareAppNameString SnmpAdminString
  ocStbHostSoftwareAppVersionNumber SnmpAdminString
  ocStbHostSoftwareStatus INTEGER

OcStbHostSystemTempEntry  
SEQUENCE    
  ocStbHostSystemTempIndex Unsigned32
  ocStbHostSystemTempDescr SnmpAdminString
  ocStbHostSystemTempValue Integer32
  ocStbHostSystemTempLastUpdate TimeStamp

OcStbHostSystemHomeNetworkEntry  
SEQUENCE    
  ocStbHostSystemHomeNetworkIndex Unsigned32
  ocStbHostSystemHomeNetworkMaxClients Integer32
  ocStbHostSystemHomeNetworkHostDRMStatus INTEGER
  ocStbHostSystemHomeNetworkConnectedClients Integer32
  ocStbHostSystemHomeNetworkClientMacAddress MacAddress
  ocStbHostSystemHomeNetworkClientIpAddress InetAddress
  ocStbHostSystemHomeNetworkClientDRMStatus Integer32

OcStbHostSystemMemoryReportEntry  
SEQUENCE    
  ocStbHostSystemMemoryReportIndex Unsigned32
  ocStbHostSystemMemoryReportMemoryType INTEGER
  ocStbHostSystemMemoryReportMemorySize Integer32

OcStbHostCCAppInfoEntry  
SEQUENCE    
  ocStbHostCCAppInfoIndex Unsigned32
  ocStbHostCCApplicationType Unsigned32
  ocStbHostCCApplicationName SnmpAdminString
  ocStbHostCCApplicationVersion Unsigned32
  ocStbHostCCAppInfoPage OCTET STRING

Defined Values

ocStbHostMibModule 1.3.6.1.4.1.4491.2.3.1
This MIB module contains the management objects for the management of OpenCable Set-top Host Device.
MODULE-IDENTITY    

ocStbHostNotifications 1.3.6.1.4.1.4491.2.3.1.0
OBJECT IDENTIFIER    

ocStbHostMibObjects 1.3.6.1.4.1.4491.2.3.1.1
OBJECT IDENTIFIER    

ocStbHostSystem 1.3.6.1.4.1.4491.2.3.1.1.1
OBJECT IDENTIFIER    

ocStbHostHWIdentifiers 1.3.6.1.4.1.4491.2.3.1.1.1.1
OBJECT IDENTIFIER    

ocStbHostInterfaces 1.3.6.1.4.1.4491.2.3.1.1.1.2
OBJECT IDENTIFIER    

ocStbHostSerialNumber 1.3.6.1.4.1.4491.2.3.1.1.1.1.1
The manufacturer's serial number for this device.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

ocStbHostHostID 1.3.6.1.4.1.4491.2.3.1.1.1.1.2
Allows the manager to retrieve the 40-bit Host ID of the ocStbHost (SNMP apdu TLV #1) in the string format indicated below: M-MMU-UUU-UUU-UUL Where: M-MM is the decimal representation of the 10-bit CHICA assigned manufacturer number. U-UUU-UUU-UU is the decimal representation of the 30-bit manufacturer assigned unit number. L is a Luhn check digit calculated over the preceding 12 decimal digits. If the Host ID is unknown, then the string shall be all zeros e.g., '0-000-000-000-000'.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(17)  

ocStbHostCapabilities 1.3.6.1.4.1.4491.2.3.1.1.1.1.3
The capabilities indication of the STB device. 'other' means a device which is not described by one of the other enumerations in this list. 'ochd2' means the STB device is an OpenCable Host Device Version 2 Compliant device. 'embedded' means the STB device is of the non-removable security type. 'dcas' means the STB device is of the downloadable security type. 'ochd21' means the STB device is an OpenCable Host Device Version 2.1 Compliant device. 'bocr' means the STB is bi-directional OCUR compliant.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), ochd2(2), embedded(3), dcas(4), ochd21(5), bocr(6)  

ocStbHostDevInterfaceTypes 1.3.6.1.4.1.4491.2.3.1.1.1.2.1
OBJECT IDENTIFIER    

ocStbHostOther 1.3.6.1.4.1.4491.2.3.1.1.1.2.1.1
The type identifier used for an interface not defined in this MIB.
Status: current Access: read-only
OBJECT-IDENTITY    

ocStbHostScte55FdcRx 1.3.6.1.4.1.4491.2.3.1.1.1.2.1.2
The type identifier used for SCTE-55 FDC Receiver (i.e., out-of-band downstream tuner).
Status: current Access: read-only
OBJECT-IDENTITY    

ocStbHostScte55RdcTx 1.3.6.1.4.1.4491.2.3.1.1.1.2.1.3
The type identifier used for SCTE-55 RDC Transmitter (i.e., out-of-band upstream transmitter).
Status: current Access: read-only
OBJECT-IDENTITY    

ocStbHostScte40FatRx 1.3.6.1.4.1.4491.2.3.1.1.1.2.1.4
The type identifier used for SCTE-40 FAT Receiver (i.e., in-band video tuner).
Status: current Access: read-only
OBJECT-IDENTITY    

ocStbHostBbVideoIn 1.3.6.1.4.1.4491.2.3.1.1.1.2.1.5
The type identifier used for baseband video input.
Status: current Access: read-only
OBJECT-IDENTITY    

ocStbHostBbAudioIn 1.3.6.1.4.1.4491.2.3.1.1.1.2.1.6
The type identifier used for baseband audio input.
Status: current Access: read-only
OBJECT-IDENTITY    

ocStbHostBbVideoOut 1.3.6.1.4.1.4491.2.3.1.1.1.2.1.7
The type identifier used for baseband video output.
Status: current Access: read-only
OBJECT-IDENTITY    

ocStbHostBbAudioOut 1.3.6.1.4.1.4491.2.3.1.1.1.2.1.8
The type identifier used for baseband audio output.
Status: current Access: read-only
OBJECT-IDENTITY    

ocStbHostRfOutCh 1.3.6.1.4.1.4491.2.3.1.1.1.2.1.9
The type identifier used for analog RF output.
Status: current Access: read-only
OBJECT-IDENTITY    

ocStbHostSVideoIn 1.3.6.1.4.1.4491.2.3.1.1.1.2.1.10
The type identifier used for SVideo input.
Status: current Access: read-only
OBJECT-IDENTITY    

ocStbHostSVideoOut 1.3.6.1.4.1.4491.2.3.1.1.1.2.1.11
The type identifier used for SVideo output.
Status: current Access: read-only
OBJECT-IDENTITY    

ocStbHostComponentIn 1.3.6.1.4.1.4491.2.3.1.1.1.2.1.12
The type identifier used for Component input.
Status: current Access: read-only
OBJECT-IDENTITY    

ocStbHostComponentOut 1.3.6.1.4.1.4491.2.3.1.1.1.2.1.13
The type identifier used for Component output.
Status: current Access: read-only
OBJECT-IDENTITY    

ocStbHostDviIn 1.3.6.1.4.1.4491.2.3.1.1.1.2.1.14
The type identifier used for DVI input.
Status: current Access: read-only
OBJECT-IDENTITY    

ocStbHostDviOut 1.3.6.1.4.1.4491.2.3.1.1.1.2.1.15
The type identifier used for DVI output.
Status: current Access: read-only
OBJECT-IDENTITY    

ocStbHostHdmiIn 1.3.6.1.4.1.4491.2.3.1.1.1.2.1.16
The type identifier used for HDMI input.
Status: current Access: read-only
OBJECT-IDENTITY    

ocStbHostHdmiOut 1.3.6.1.4.1.4491.2.3.1.1.1.2.1.17
The type identifier used for HDMI output.
Status: current Access: read-only
OBJECT-IDENTITY    

ocStbHostRcaSpdifIn 1.3.6.1.4.1.4491.2.3.1.1.1.2.1.18
The type identifier used for RCA SPDIF input.
Status: current Access: read-only
OBJECT-IDENTITY    

ocStbHostRcaSpdifOut 1.3.6.1.4.1.4491.2.3.1.1.1.2.1.19
The type identifier used for RCA SPDIF output.
Status: current Access: read-only
OBJECT-IDENTITY    

ocStbHostToslinkSpdifIn 1.3.6.1.4.1.4491.2.3.1.1.1.2.1.20
The type identifier used for Toslink SPDIF input.
Status: current Access: read-only
OBJECT-IDENTITY    

ocStbHostToslinkSpdifOut 1.3.6.1.4.1.4491.2.3.1.1.1.2.1.21
The type identifier used for Toslink SPDIF output.
Status: current Access: read-only
OBJECT-IDENTITY    

ocStbHostDisplayOut 1.3.6.1.4.1.4491.2.3.1.1.1.2.1.22
The type identifier used for the television screen output.
Status: current Access: read-only
OBJECT-IDENTITY    

ocStbHost1394In 1.3.6.1.4.1.4491.2.3.1.1.1.2.1.23
The type identifier used for IEEE-1394 input.
Status: current Access: read-only
OBJECT-IDENTITY    

ocStbHost1394Out 1.3.6.1.4.1.4491.2.3.1.1.1.2.1.24
The type identifier used for IEEE-1394 output.
Status: current Access: read-only
OBJECT-IDENTITY    

ocStbHostDRIInterface 1.3.6.1.4.1.4491.2.3.1.1.1.2.1.25
The type identifier used for the DRI interface.
Status: current Access: read-only
OBJECT-IDENTITY    

ocStbHostAVInterfaceTable 1.3.6.1.4.1.4491.2.3.1.1.1.2.2
This table contains a list of A/V (Audio/Video) interfaces (video inputs/outputs, tuners, audio inputs/outputs) in the ocStbHost.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OcStbHostAVInterfaceEntry

ocStbHostAVInterfaceEntry 1.3.6.1.4.1.4491.2.3.1.1.1.2.2.1
Each entry describes the type and status of the A/V interface on the ocStbHost. The details of A/V interface entries may be defined in table extensions as indicated in the MIB object ocStbHostAVInterfaceType.
Status: current Access: not-accessible
OBJECT-TYPE    
  OcStbHostAVInterfaceEntry  

ocStbHostAVInterfaceIndex 1.3.6.1.4.1.4491.2.3.1.1.1.2.2.1.1
Index of the table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..4294967295  

ocStbHostAVInterfaceType 1.3.6.1.4.1.4491.2.3.1.1.1.2.2.1.2
An indication of the type of interface. If this value is ocStbHostComponentOut then a corresponding entry exists in the ocStbHostComponentVideoTable. If this value is ocStbHostRFOutCh then a corresponding entry exists in the ocStbHostRFChannelOutTable. If this value is ocStbHostScte40FatRx then a corresponding entry exists in the ocStbHostInBandTunerTable. If this value is ocStbHostDviOut or ocStbHostHdmiOut then a corresponding entry exists in the ocStbHostDVIHDMITable If this value is ocStbHost1394Out then a corresponding entry exists in the ocStbHostIEEE1394Table If this value is hrDeviceOther then no further information is available for the device.
Status: current Access: read-only
OBJECT-TYPE    
  AutonomousType  

ocStbHostAVInterfaceDesc 1.3.6.1.4.1.4491.2.3.1.1.1.2.2.1.3
Textual description of the A/V Interface
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

ocStbHostAVInterfaceStatus 1.3.6.1.4.1.4491.2.3.1.1.1.2.2.1.4
Status of the interface. 'enabled' indicates the A/V interface is active and can be used for the user. 'disabled' indicates the A/V interface is currently not available for the user due to hardware, software or configuration conditions. Additional information about the interface status may be available in the A/V Type interface Table extensions.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

ocStbHostIEEE1394Objects 1.3.6.1.4.1.4491.2.3.1.1.1.2.3
OBJECT IDENTIFIER    

ocStbHostIEEE1394Table 1.3.6.1.4.1.4491.2.3.1.1.1.2.3.1
This table contains attributes associated with the ocStbHost Interfaces of type IEEE 1394.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OcStbHostIEEE1394Entry

ocStbHostIEEE1394Entry 1.3.6.1.4.1.4491.2.3.1.1.1.2.3.1.1
An entry exists in this table for each interface of the type IEEE 1394.
Status: current Access: not-accessible
OBJECT-TYPE    
  OcStbHostIEEE1394Entry  

ocStbHostIEEE1394ActiveNodes 1.3.6.1.4.1.4491.2.3.1.1.1.2.3.1.1.1
This object allows the manager to retrieve the number of nodes connected to the 1394 bus of the ocStbHost. The value '-1' means unknown number of nodes.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -1 | 0..64  

ocStbHostIEEE1394DataXMission 1.3.6.1.4.1.4491.2.3.1.1.1.2.3.1.1.2
This object allows the manager to retrieve the state of data being transmitted over the 1394 bus. True indicates that data is being transmitted over the 1394 bus.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

ocStbHostIEEE1394DTCPStatus 1.3.6.1.4.1.4491.2.3.1.1.1.2.3.1.1.3
This object allows the manager to retrieve the state of DTCP on the device. True indicates that DTCP is enabled and content is being encrypted of the 1394 link on the ocStbHost.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

ocStbHostIEEE1394LoopStatus 1.3.6.1.4.1.4491.2.3.1.1.1.2.3.1.1.4
This object allows the manager to retrieve the state of a Loop present on the 1394 bus. True indicates that a Loop is present on the 1394 bus.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

ocStbHostIEEE1394RootStatus 1.3.6.1.4.1.4491.2.3.1.1.1.2.3.1.1.5
This object allows the manager to retrieve the state of Root Status on the device. True indicates that the set-top is the Root node on the 1394 bus.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

ocStbHostIEEE1394CycleIsMaster 1.3.6.1.4.1.4491.2.3.1.1.1.2.3.1.1.6
This object allows the manager to retrieve the state of Cycle Master on the device. True indicates that the set-top is Cycle Master on the 1394 bus.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

ocStbHostIEEE1394IRMStatus 1.3.6.1.4.1.4491.2.3.1.1.1.2.3.1.1.7
This object allows the manager to retrieve the state of Isochronous Resource Master on the device. True indicates that the set-top is IRM on the 1394 bus.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

ocStbHostIEEE1394AudioMuteStatus 1.3.6.1.4.1.4491.2.3.1.1.1.2.3.1.1.8
The value 'true' indicates that the audio signal is muted for this Interface. 'false' means the audio is not muted.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

ocStbHostIEEE1394VideoMuteStatus 1.3.6.1.4.1.4491.2.3.1.1.1.2.3.1.1.9
The value 'true' indicates that the video signal is muted for this Interface. 'false' means the video signal is not muted.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

ocStbHostIEEE1394ConnectedDevicesTable 1.3.6.1.4.1.4491.2.3.1.1.1.2.3.2
This table contains A/D Source Selection attributes associated to devices connected to the ocStbHost Interfaces of type IEEE 1394.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OcStbHostIEEE1394ConnectedDevicesEntry

ocStbHostIEEE1394ConnectedDevicesEntry 1.3.6.1.4.1.4491.2.3.1.1.1.2.3.2.1
An entry exist in this table for each device connected to all Interfaces of the type IEEE 1394.
Status: current Access: not-accessible
OBJECT-TYPE    
  OcStbHostIEEE1394ConnectedDevicesEntry  

ocStbHostIEEE1394ConnectedDevicesIndex 1.3.6.1.4.1.4491.2.3.1.1.1.2.3.2.1.1
The unique identifier of the connected device entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..4294967295  

ocStbHostIEEE1394ConnectedDevicesAVInterfaceIndex 1.3.6.1.4.1.4491.2.3.1.1.1.2.3.2.1.2
This object allows the manager to retrieve the index value associated with the IEEE1394 instance of ocStbHostAVInterfaceIndex to which the device is physically connected.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..4294967295  

ocStbHostIEEE1394ConnectedDevicesSubUnitType 1.3.6.1.4.1.4491.2.3.1.1.1.2.3.2.1.3
This object allows the manager to retrieve the Subunit Type associated with the device connected to the ocStbHost's IEEE1394 interface.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER monitor(0), audio(1), printer(2), disc(3), tape(4), tuner(5), ca(6), camera(7), reserved(8), panel(9), other(10)  

ocStbHostIEEE1394ConnectedDevicesEui64 1.3.6.1.4.1.4491.2.3.1.1.1.2.3.2.1.4
This object allows the manager to retrieve the 64-bit Extended Unique Identifier (EUI-64) associated with the device connected to the ocStbHost's IEEE1394 interface.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(8)  

ocStbHostIEEE1394ConnectedDevicesADSourceSelectSupport 1.3.6.1.4.1.4491.2.3.1.1.1.2.3.2.1.5
This object allows the manager to retrieve the status of Analog/Digital Source Selection support associated with the device connected to the ocStbHost's IEEE1394 interface. 'true' indicates that the device supports A/D source selection.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

ocStbHostDigitalVideoOutput 1.3.6.1.4.1.4491.2.3.1.1.1.2.4
OBJECT IDENTIFIER    

ocStbHostDVIHDMITable 1.3.6.1.4.1.4491.2.3.1.1.1.2.4.1
This table allows the manager to retrieve information about the DVI/HDMI port of the ocStbHost.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OcStbHostDVIHDMIEntry

ocStbHostDVIHDMIEntry 1.3.6.1.4.1.4491.2.3.1.1.1.2.4.1.1
An entry exists for each A/V interface of type HDMI or DVI of the ocStbHost.
Status: current Access: not-accessible
OBJECT-TYPE    
  OcStbHostDVIHDMIEntry  

ocStbHostDVIHDMIOutputType 1.3.6.1.4.1.4491.2.3.1.1.1.2.4.1.1.2
This object defines the operational mode of the interface, where valid modes are dependant on the physical interface defined. If ocStbHostAVInterfaceIndex is DVI, then this value is always set to 1 (DVI). If ocStbHostAVInterfaceIndex is HDMI, then this value is either 1 (DVI) or 2 (HDMI).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER dvi(1), hdmi(2)  

ocStbHostDVIHDMIConnectionStatus 1.3.6.1.4.1.4491.2.3.1.1.1.2.4.1.1.3
This object allows the manager to retrieve the state of the DVI/HDMI port on the device. 'true' indicates that a device is connected to the ocStbHost.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

ocStbHostDVIHDMIRepeaterStatus 1.3.6.1.4.1.4491.2.3.1.1.1.2.4.1.1.4
This object allows the manager to retrieve the presence of a repeater connected to the ocStbHost. 'true' indicates that a repeater is connected to the ocStbHost.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

ocStbHostDVIHDMIVideoXmissionStatus 1.3.6.1.4.1.4491.2.3.1.1.1.2.4.1.1.5
This object allows the manager to retrieve the state of video transmission over the DVI/HDMI port of the ocStbHost. 'true' indicates that video is being transmitted over the DVI/HDMI link to a connected device.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

ocStbHostDVIHDMIHDCPStatus 1.3.6.1.4.1.4491.2.3.1.1.1.2.4.1.1.6
This object allows the manager to retrieve the state of the digital copy protection protocol in the interface. 'true' indicates that HDCP encryption is enabled.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

ocStbHostDVIHDMIVideoMuteStatus 1.3.6.1.4.1.4491.2.3.1.1.1.2.4.1.1.7
The value 'true' indicates that the video signal is being muted over the DVI/HDMI link. 'false' means the video signal is not muted.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

ocStbHostDVIHDMIOutputFormat 1.3.6.1.4.1.4491.2.3.1.1.1.2.4.1.1.8
This object allows the manager to retrieve the video timing format currently being transmitted over the DVI/HDMI link.
Status: current Access: read-only
OBJECT-TYPE    
  VideoOutputFormat  

ocStbHostDVIHDMIAspectRatio 1.3.6.1.4.1.4491.2.3.1.1.1.2.4.1.1.9
This object allows the manager to retrieve the aspect ratio applicable to the video timing format currently being transmitted over the DVI/HDMI link. e.g., 4/3 or 16/9.
Status: current Access: read-only
OBJECT-TYPE    
  VideoAspectRatio  

ocStbHostDVIHDMIHostDeviceHDCPStatus 1.3.6.1.4.1.4491.2.3.1.1.1.2.4.1.1.10
Connected device HDCP status.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER nonHDCPdevice(1), compliantHDCPdevice(2), revokedHDCPdevice(3)  

ocStbHostDVIHDMIAudioFormat 1.3.6.1.4.1.4491.2.3.1.1.1.2.4.1.1.11
This object allows the manager to retrieve the audio format being transmitted over the HDMI link. If this entry corresponds to a DVI interface, this object is not instantiated.
Status: current Access: read-only
OBJECT-TYPE    
  AudioOutputFormat  

ocStbHostDVIHDMIAudioSampleRate 1.3.6.1.4.1.4491.2.3.1.1.1.2.4.1.1.12
This object allows the manager to retrieve the audio sample rate being transmitted over the HDMI link. If this entry corresponds to a DVI interface, this object is not instantiated.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), samplerate32kHz(2), samplerate44kHz(3), samplerate48kHz(4), samplerate88kHz(5), samplerate96kHz(6), samplerate176kHz(7), samplerate192kHz(8)  

ocStbHostDVIHDMIAudioChannelCount 1.3.6.1.4.1.4491.2.3.1.1.1.2.4.1.1.13
This object allows the manager to retrieve the audio channel count being transmitted over the HDMI link. If this entry corresponds to a DVI interface, this object is not instantiated.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..10  

ocStbHostDVIHDMIAudioMuteStatus 1.3.6.1.4.1.4491.2.3.1.1.1.2.4.1.1.14
The value 'true' indicates that the audio signal is muted over the DVI/HDMI link. 'false' means the audio is not muted. This object is not instantiated for entries of ocStbHostDVIHDMIOutputType 'dvi'.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

ocStbHostAnalogOutput 1.3.6.1.4.1.4491.2.3.1.1.1.2.5
OBJECT IDENTIFIER    

ocStbHostComponentVideoTable 1.3.6.1.4.1.4491.2.3.1.1.1.2.5.1
This table allows the manager to retrieve information about a Component Video interface of the ocStbHost.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OcStbHostComponentVideoEntry

ocStbHostComponentVideoEntry 1.3.6.1.4.1.4491.2.3.1.1.1.2.5.1.1
An entry for each interface of type 'ocStbHostComponentOut'.
Status: current Access: not-accessible
OBJECT-TYPE    
  OcStbHostComponentVideoEntry  

ocStbHostComponentVideoConstrainedStatus 1.3.6.1.4.1.4491.2.3.1.1.1.2.5.1.1.1
This object allows the manager to retrieve the state of Constrained Video Image on the port. True indicates that video is being constrained over the component video output port.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

ocStbHostComponentOutputFormat 1.3.6.1.4.1.4491.2.3.1.1.1.2.5.1.1.2
This object allows the manager to retrieve the video format currently being transmitted over the Component Video output port.
Status: current Access: read-only
OBJECT-TYPE    
  VideoOutputFormat  

ocStbHostComponentAspectRatio 1.3.6.1.4.1.4491.2.3.1.1.1.2.5.1.1.3
This object allows the manager to retrieve the video aspect ratio currently being transmitted over the Component Video output port.
Status: current Access: read-only
OBJECT-TYPE    
  VideoAspectRatio  

ocStbHostComponentVideoMuteStatus 1.3.6.1.4.1.4491.2.3.1.1.1.2.5.1.1.4
The value 'true' indicates that the video signal is muted for this Interface. 'false' means the video signal is not muted.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

ocStbHostRFChannelOutTable 1.3.6.1.4.1.4491.2.3.1.1.1.2.5.2
This table allows the manager to retrieve information about an RF channel output interface of the ocStbHost.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OcStbHostRFChannelOutEntry

ocStbHostRFChannelOutEntry 1.3.6.1.4.1.4491.2.3.1.1.1.2.5.2.1
An entry for each interface of type 'ocStbHostRFOutCh'.
Status: current Access: not-accessible
OBJECT-TYPE    
  OcStbHostRFChannelOutEntry  

ocStbHostRFChannelOut 1.3.6.1.4.1.4491.2.3.1.1.1.2.5.2.1.2
Indicates the RF channel out value. Typical values are 3 or 4 for Channels 3 and 4, respectively.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 3..99  

ocStbHostRFChannelOutAudioMuteStatus 1.3.6.1.4.1.4491.2.3.1.1.1.2.5.2.1.3
The value 'true' indicates that the audio signal is muted for this Interface. 'false' means the audio is not muted.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

ocStbHostRFChannelOutVideoMuteStatus 1.3.6.1.4.1.4491.2.3.1.1.1.2.5.2.1.4
The value 'true' indicates that the video signal is muted for this Interface. 'false' means the video signal is not muted.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

ocStbHostSPDIfTable 1.3.6.1.4.1.4491.2.3.1.1.1.2.6
This table allows the manager to retrieve information about the SONY, Philips Digital (SPD) Interface of the ocStbHost.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OcStbHostSPDIfEntry

ocStbHostSPDIfEntry 1.3.6.1.4.1.4491.2.3.1.1.1.2.6.1
An entry exists for each Audio interface of type SPD.
Status: current Access: not-accessible
OBJECT-TYPE    
  OcStbHostSPDIfEntry  

ocStbHostSPDIfAudioFormat 1.3.6.1.4.1.4491.2.3.1.1.1.2.6.1.1
The format of the Audio stream transmitted over this interface.
Status: current Access: read-only
OBJECT-TYPE    
  AudioOutputFormat  

ocStbHostSPDIfAudioMuteStatus 1.3.6.1.4.1.4491.2.3.1.1.1.2.6.1.2
The value 'true' indicates that the audio signal is muted over the SPDIF link. 'false' means the audio is not muted.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

ocStbHostServiceProgramInfo 1.3.6.1.4.1.4491.2.3.1.1.1.2.7
OBJECT IDENTIFIER    

ocStbHostInBandTunerTable 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.1
This Object Table allows the manager to retrieve information regarding the In-Band tuner(s) in the ocStbHost.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OcStbHostInBandTunerEntry

ocStbHostInBandTunerEntry 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.1.1
This entry contains information regarding a tuner of type ocStbHostScte40FatRx in the ocStbHost.
Status: current Access: not-accessible
OBJECT-TYPE    
  OcStbHostInBandTunerEntry  

ocStbHostInBandTunerModulationMode 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.1.1.1
The In-band tuner modulation mode. Modulation modes are as follows: other - IB is configured in a manner not described by any other listed mode. Analog - IB is configured for analog service. QAM-64 - IB is configured for a digital service that is 64-QAM. QAM-256 - IB is configured for a digital service that is 256-QAM.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), analog(2), qam64(3), qam256(4)  

ocStbHostInBandTunerFrequency 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.1.1.2
This object allows the manager to retrieve the center frequency of the currently tuned channel in Hz.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

ocStbHostInBandTunerInterleaver 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.1.1.3
The in-band interface interleaver value. set to '3' current operational mode 'taps64Increment2' set to '4' current operational mode 'taps128Increment1' set to '5' current operational mode 'taps128increment2' set to '6' current operational mode 'taps128increment3' set to '7' current operational mode 'taps128increment4' set to '8' current operational mode 'taps32increment4' set to '9' current operational mode 'taps16increment8' set to '10' current operational mode 'taps8increment16'
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(1), other(2), taps64Increment2(3), taps128Increment1(4), taps128increment2(5), taps128increment3(6), taps128increment4(7), taps32increment4(8), taps16increment8(9), taps8increment16(10)  

ocStbHostInBandTunerPower 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.1.1.4
The received power level of this in-band interface.
Status: current Access: read-write
OBJECT-TYPE    
  TenthdBmV  

ocStbHostInBandTunerAGCValue 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.1.1.5
This object allows the manager to retrieve the In-band channel AGC value (%). When an In-band Carrier Lock is indicated, a value of 0 (zero) indicates that the ocStbHost does not compute the value.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..100  

ocStbHostInBandTunerSNRValue 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.1.1.6
This object allows the manager to retrieve the In-band channel SNR value (1/10 dB). When an In-band Carrier Lock is indicated, a value of 0 (zero) indicates that the ocStbHost does not compute the value.
Status: current Access: read-only
OBJECT-TYPE    
  TenthdB  

ocStbHostInBandTunerUnerroreds 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.1.1.7
Codewords received on this channel without error. Discontinuities in the value of this counter can occur at reinitialization of the managed system, and at other times as indicated by the value of ifCounterDiscontinuityTime for the associated ifIndex.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

ocStbHostInBandTunerCorrecteds 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.1.1.8
Codewords received on this in-band channel with correctable errors. Discontinuities in the value of this counter can occur at reinitialization of the managed system.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

ocStbHostInBandTunerUncorrectables 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.1.1.9
Codewords received on this in-band channel with uncorrectable errors. Discontinuities in the value of this counter can occur at reinitialization of the managed system.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

ocStbHostInBandTunerCarrierLockLost 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.1.1.10
The number of times the ocStbHost has detected carrier Lock is lost. Discontinuities in the value of this counter can occur at reinitialization of the managed system.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

ocStbHostInBandTunerPCRErrors 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.1.1.11
The number of times the Program Clock Reference (PCR) detected Synchronization errors; e.g., wrong PCR from multiplexer, excessive CPR Jitter, etc. Discontinuities in the value of this counter can occur at reinitialization of the managed system.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

ocStbHostInBandTunerPTSErrors 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.1.1.12
The number of Presentation TimeStamp (PTS) packets that encounter sequencing errors. Discontinuities in the value of this counter can occur at reinitialization of the managed system.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

ocStbHostInBandTunerState 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.1.1.13
The In-band tuner current state. Modulation modes are as follows: ready - indicates that the tuner is in idle mode (not currently in use). waitingSync - indicates that the tuner is trying to find sync on an analog channel. waitingQam - indicates that the tuner is trying to tune to the desired QAM frequency and lock onto valid data. foundSync - indicates that the tuner has successfully tuned to an analog channel. foundQam - indicates that the tuner has successfully tuned to a digital channel.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ready(1), waitingSync(2), waitingQam(3), foundSync(4), foundQam(5), unknown(6), standby(7)  

ocStbHostInBandTunerBER 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.1.1.14
The average Bit Error Rate range since last tune to a digital channel. This value is determined by dividing the number of erroneous bits by the total number of bits transmitted since QAM lock. Report value of 7 if tuned to an analog channel.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER berGreaterThan10e2(1), berRange10e2ToGreaterThan10e4(2), berRange10e4ToGreaterThan10e6(3), berRange10e6ToGreaterThan10e8(4), berRange10e8ToGreaterThan10e12(5), berEqualToOrLessThan10e12(6), berNotApplicable(7)  

ocStbHostInBandTunerSecsSinceLock 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.1.1.15
The amount of time, in seconds, since the last tuner lock on a valid data signal. Each time the tuner locks the ocStbHostInBandTunerUnerroreds, ocStbHostInBandTunerCorrecteds, and ocStbHostInBandTunerUncorrectables, counters should be set to 0.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

ocStbHostInBandTunerEqGain 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.1.1.16
The value of the equalizer gain on the QAM data channel. A value of 0 (zero) indicates that the ocStbHost does not compute the value.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

ocStbHostInBandTunerMainTapCoeff 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.1.1.17
The normalized main tap coefficient used for calibrating data path delay or frequency response. A value of 0 (zero) indicates that the ocStbHost does not compute the value.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..32767  

ocStbHostProgramStatusTable 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.2
A table of current program content being forwarded by the ocStbHost.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OcStbHostProgramStatusEntry

ocStbHostProgramStatusEntry 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.2.1
There is an entry in this table for each active program content path. This means that the same program content source and/or destination can be associated to multiple A/V interface combinations as different entries in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  OcStbHostProgramStatusEntry  

ocStbHostProgramIndex 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.2.1.1
Index for Program Status Entry Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..20  

ocStbHostProgramAVSource 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.2.1.2
Defines the source interface associated with this entry. Example sources are interfaces listed in the ifTable, interfaces listed in ocStbAVInterfaceTable, or a Host Resources Device such as a DVR. If the source corresponds to an entry in the ocStbAVInterfaceTable, this object reports the ocStbAVInterfaceType instance of the source interface. If the source corresponds to a resource listed in the ifTable, this object reports the ifIndex instance of the source interface. If the source corresponds to a resource listed in hrDeviceTable, this object reports the hrDeviceType instance of the source interface. Other table rows may be designated by this object as appropriate to the particular source.
Status: current Access: read-only
OBJECT-TYPE    
  RowPointer  

ocStbHostProgramAVDestination 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.2.1.3
Defines the destination interface associated with this entry. Example destinations are interfaces listed in the ifTable, interfaces listed in ocStbAVInterfaceTable, or a Host Resource Device such as a DVR. If the destination corresponds to an entry in the ocStbAVInterfaceTable, this object reports the ocStbAVInterfaceType instance of the destination interface. If the destination corresponds to an interface listed in the ifTable, this object reports the ifIndex instance of the destination interface. If the destination corresponds to a resource listed in the hrDeviceTable, this object reports the hrDeviceType instance of the destination interface. Other table rows may be designated by this object as appropriate to the particular destination.
Status: current Access: read-only
OBJECT-TYPE    
  RowPointer  

ocStbHostProgramContentSource 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.2.1.4
A pointer to the first visible object structure that defines the type of content associated to the A/V source interface. If the content is from an MPEG2 stream, this object points to the first visible object in ocStbHostMpeg2ContentEntry. Vendor-specific Content models may be defined in the vendor enterprise IANA assigned OID. This object reports 'zeroDotZero' value if no content information is available.
Status: current Access: read-only
OBJECT-TYPE    
  RowPointer  

ocStbHostProgramContentDestination 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.2.1.5
A pointer to the first visible object structure that defines the type of content associated to the A/V destination interface. For example, if the content for the destination interface is an MPEG2 stream (e.g., IEEE 1394 SPTS), this object points to the first visible object in ocStbHostMpeg2ContentEntry. Vendor-specific Content models may be defined in the vendor enterprise IANA assigned OID. This object reports 'zeroDotZero' value if no content information is available.
Status: current Access: read-only
OBJECT-TYPE    
  RowPointer  

ocStbHostMpeg2ContentTable 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.3
Contains information associated to an MPEG-2 Program carried by an MPEG-2 transport stream. Entries in this table can be associated to interfaces receiving or forwarding MPEG-2 content.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OcStbHostMpeg2ContentEntry

ocStbHostMpeg2ContentEntry 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.3.1
The conceptual row for this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  OcStbHostMpeg2ContentEntry  

ocStbHostMpeg2ContentIndex 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.3.1.1
The unique identifier for the Mpeg2 Content entries in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..20  

ocStbHostMpeg2ContentProgramNumber 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.3.1.2
The program Number associated with active content within the ocStbHost.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

ocStbHostMpeg2ContentTransportStreamID 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.3.1.3
Defines the transport stream ID associated with the program number.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

ocStbHostMpeg2ContentTotalStreams 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.3.1.4
Defines the total number of elementary streams associated with the program number.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

ocStbHostMpeg2ContentSelectedVideoPID 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.3.1.5
This object allows the manager to retrieve the PID associated to the selected video stream. The value '-1' indicates that no video stream is being selected or identified. The value is the 13-bit PID value expressed in decimal.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -1 | 1..8191  

ocStbHostMpeg2ContentSelectedAudioPID 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.3.1.6
The selected audio PID. The value '-1' indicates no audio stream identified.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -1 | 1..8191  

ocStbHostMpeg2ContentOtherAudioPIDs 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.3.1.7
Then value 'true' indicates the MPEG-2 program has more than one audio PID. 'false' indicates the MPEG-2 program has only one audio PID.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

ocStbHostMpeg2ContentCCIValue 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.3.1.8
This value allows the manager to retrieve the encryption Mode Indication (EMI) Bits of the Copy Control Information (CCI) byte associated with the service.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER copyFreely(0), copyNoMore(1), copyOneGeneration(2), copyNever(3), undefined(4)  

ocStbHostMpeg2ContentAPSValue 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.3.1.9
This value allows the manager to retrieve the Analog Protection System (APS) bits of the Copy Control Information (CCI) byte associated with the service. 'type1' indicates AGC ON, split burst OFF 'type2' indicates AGC ON, 2-line split burst 'type3' indicates AGC ON, 4-line split burst.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER type1(1), type2(2), type3(3), noMacrovision(4), notDefined(5)  

ocStbHostMpeg2ContentCITStatus 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.3.1.10
This value allows the manager to retrieve the state of the Constrained Image Trigger(CIT). 'true' indicates image constraint required. 'false' indicates image constraint not asserted.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

ocStbHostMpeg2ContentBroadcastFlagStatus 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.3.1.11
This value allows the manager to retrieve the state of Broadcast Flag in the source interface. 'true' indicates Broadcast Flag present. 'false' indicates Broadcast Flag not present.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

ocStbHostMpeg2ContentEPNStatus 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.3.1.12
This object allows the manager to retrieve the EPN status of the MPEG stream. 'true' indicates that EPN is asserted.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

ocStbHostMpeg2ContentPCRPID 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.3.1.13
This object allows the manager to retrieve the PCR PID associated to the selected video stream. The value '-1' indicates that no video stream is being selected or identified. The value is the 13-bit PCR PID value expressed in decimal.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -1 | 1..8191  

ocStbHostMpeg2ContentPCRLockStatus 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.3.1.14
The status of the Program Clock Reference lock.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notLocked(1), locked(2)  

ocStbHostMpeg2ContentDecoderPTS 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.3.1.15
The value of the MPEG decoder Presentation TimeStamp (PTS).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

ocStbHostMpeg2ContentDiscontinuities 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.3.1.16
The sum of the audio and video PID discontinuities detected on the MPEG stream. The values are based on the time since PCR lock on the current PIDs or stream being reported
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

ocStbHostMpeg2ContentPktErrors 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.3.1.17
The number of errors detected in the MPEG stream. The Values are based on the time since PCR lock on the Current PIDs or stream being reported
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

ocStbHostMpeg2ContentPipelineErrors 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.3.1.18
The number of errors reported exclusively by the MPEG decoder.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

ocStbHostMpeg2ContentDecoderRestarts 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.3.1.19
The number of times the software driver restarted the MPEG decoding process.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

ocStbHostAnalogVideoTable 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.4
Contains information about the Analog Video signal. Entries in this table can be associated to interfaces receiving or forwarding analog content.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OcStbHostAnalogVideoEntry

ocStbHostAnalogVideoEntry 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.4.1
The conceptual row for this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  OcStbHostAnalogVideoEntry  

ocStbHostAnalogVideoProtectionStatus 1.3.6.1.4.1.4491.2.3.1.1.1.2.7.4.1.1
The analog protection system (APS) of this Video content entry. The possible values are: 'copyProtectionOff' means the Macrovision Analog protection is off 'splitBurstOff' means the AGC (Automatic Gain Control) is on and the split burst is off. 'twoLineSplitBurst' means AGC is on with two-line split burst. 'fourLineSplitBurst' means AGC is on with four-line split burst. This object is instantiated only for A/V output interfaces that support APS like but not limited to: 'ocStbHostRfOutCh', 'ocStbHostSVideoOut' and 'ocStbHostBbVideoOut'. The A/V interfaces 'ocStbHostComponentOut' only support 'splitBurstOff' APS mode for the video formats 'format480i' and 'format480p'.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER copyProtectionOff(0), splitBurstOff(1), twoLineSplitBurst(2), fourLineSplitBurst(3)  

ocStbHostQpskObjects 1.3.6.1.4.1.4491.2.3.1.1.1.2.8
OBJECT IDENTIFIER    

ocStbHostQpskFDCFreq 1.3.6.1.4.1.4491.2.3.1.1.1.2.8.1
The frequency to which the QPSK receiver is currently tuned.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

ocStbHostQpskRDCFreq 1.3.6.1.4.1.4491.2.3.1.1.1.2.8.2
The frequency to which the QPSK transmitter is currently tuned.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

ocStbHostQpskFDCBer 1.3.6.1.4.1.4491.2.3.1.1.1.2.8.3
The rate at which bit errors are occurring based on the number of data errors since the frequency has been locked.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER berGreaterThan10e2(1), berRange10e2ToGreaterThan10e4(2), berRange10e4ToGreaterThan10e6(3), berRange10e6ToGreaterThan10e8(4), berRange10e8ToGreaterThan10e12(5), berEqualToOrLessThan10e12(6), berNotApplicable(7)  

ocStbHostQpskFDCStatus 1.3.6.1.4.1.4491.2.3.1.1.1.2.8.4
Forward data channel lock status.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notLocked(1), locked(2)  

ocStbHostQpskFDCBytesRead 1.3.6.1.4.1.4491.2.3.1.1.1.2.8.5
The number of bytes successfully read since the frequency was locked.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

ocStbHostQpskFDCPower 1.3.6.1.4.1.4491.2.3.1.1.1.2.8.6
The power level, in dBmV, of the forward data channel.
Status: current Access: read-only
OBJECT-TYPE    
  TenthdBmV  

ocStbHostQpskFDCLockedTime 1.3.6.1.4.1.4491.2.3.1.1.1.2.8.7
The number of seconds that the current FDC frequency has been locked.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

ocStbHostQpskFDCSNR 1.3.6.1.4.1.4491.2.3.1.1.1.2.8.8
This object allows the manager to retrieve the FDC SNR value (1/10 dB).
Status: current Access: read-only
OBJECT-TYPE    
  TenthdB  

ocStbHostQpskAGC 1.3.6.1.4.1.4491.2.3.1.1.1.2.8.9
This object allows the manager to retrieve the OOB channel Automatic Gain Control value (%).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

ocStbHostQpskRDCPower 1.3.6.1.4.1.4491.2.3.1.1.1.2.8.10
The power output level, in dBmV, of the QPSK transmitter.
Status: current Access: read-only
OBJECT-TYPE    
  TenthdBmV  

ocStbHostQpskRDCDataRate 1.3.6.1.4.1.4491.2.3.1.1.1.2.8.11
The data rate (in kbps) of the RDC.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER kbps256(1), kbps1544(2), kbps3088(3)  

ocStbHostEasObjects 1.3.6.1.4.1.4491.2.3.1.1.1.3
OBJECT IDENTIFIER    

ocStbHostEasCodes 1.3.6.1.4.1.4491.2.3.1.1.1.3.1
OBJECT IDENTIFIER    

ocStbEasMessageStateCode 1.3.6.1.4.1.4491.2.3.1.1.1.3.1.1
This object allows the manager to retrieve the EAS State Code utilized by the STB. A value of 0 indicates that the code is not defined, thus the eSTB does not discriminate any State Code defined in an EAS message.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..99  

ocStbEasMessageCountyCode 1.3.6.1.4.1.4491.2.3.1.1.1.3.1.2
This object allows the manager to retrieve the EAS County Code utilized by the STB. A value of 0 indicates that the code is not defined, thus the eSTB ignores any County Code defined in an EAS message.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..999  

ocStbEasMessageCountySubdivisionCode 1.3.6.1.4.1.4491.2.3.1.1.1.3.1.3
This object allows the manager to retrieve the EAS County Sub Code utilized by the STB. A value of 0 indicates that the code is not defined, thus the eSTB ignores it and any County Subdivision Code defined in an EAS message is accepted.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..9  

ocStbHostSecuritySubSystem 1.3.6.1.4.1.4491.2.3.1.1.2
OBJECT IDENTIFIER    

ocStbHostSecurityIdentifier 1.3.6.1.4.1.4491.2.3.1.1.2.2
The security identifier of the ocStbHost. This object represents the 40-bit Host_ID obtained from the Host x509 certificate.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

ocStbHostCASystemIdentifier 1.3.6.1.4.1.4491.2.3.1.1.2.3
Conditional access system identifier defined by DVB and MPEG. This object represents the 16-bit CA_system_id obtained from the ca_info_reply apdu.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

ocStbHostCAType 1.3.6.1.4.1.4491.2.3.1.1.2.4
The Conditional Access (CA) supported by the host device. 'other' means a CA which is not described by one of the other enumerations in this list. 'embedded' means a vendor-specific embedded CA 'cablecard' means OpenCable CableCARD is supported. 'dcas' means software downloadable CA is supported.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), embedded(2), cablecard(3), dcas(4)  

ocStbHostSoftware 1.3.6.1.4.1.4491.2.3.1.1.3
OBJECT IDENTIFIER    

ocStbHostDeviceSoftwareBase 1.3.6.1.4.1.4491.2.3.1.1.3.1
OBJECT IDENTIFIER    

ocStbHostFirmwareDownloadStatus 1.3.6.1.4.1.4491.2.3.1.1.3.2
OBJECT IDENTIFIER    

ocStbHostSoftwareApplicationInfo 1.3.6.1.4.1.4491.2.3.1.1.3.3
OBJECT IDENTIFIER    

ocStbHostSoftwareFirmwareVersion 1.3.6.1.4.1.4491.2.3.1.1.3.1.1
The platform code software version currently operating in this device. This object should be in the syntax used by the individual vendor to identify software versions. The device must return a string descriptive of the current software load. This object is shared with docsDevSwCurrentVers.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

ocStbHostSoftwareOCAPVersion 1.3.6.1.4.1.4491.2.3.1.1.3.1.2
This object returns a string indicating the latest version of the OCAP profile supported by this device, e.g., '1.0'.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

ocStbHostFirmwareImageStatus 1.3.6.1.4.1.4491.2.3.1.1.3.2.1
This object details the image status recently downloaded 'imageAuthorized' means the image is valid. 'imageCorrupted' means the image is invalid. 'imageCertFailure' means CVC authentication has failed. 'imageMaxDownloadRetry' means the maximum number of code file download retries has been reached. When the value of this object is imageMaxDownloadRetry(4), the value of ocStbHostSoftwareCodeDownloadStatus must be downloadingFailed(3). 'imageMaxRebootRetry' means the maximum number of reboots has occurred after code file download.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER imageAuthorized(1), imageCorrupted(2), imageCertFailure(3), imageMaxDownloadRetry(4), imageMaxRebootRetry(5)  

ocStbHostFirmwareCodeDownloadStatus 1.3.6.1.4.1.4491.2.3.1.1.3.2.2
This object details the download status of the target image. 'downloadingComplete' means the image download was successful. 'downloadingFailed' means the image download failed.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER downloadingStarted(1), downloadingComplete(2), downloadingFailed(3)  

ocStbHostFirmwareCodeObjectName 1.3.6.1.4.1.4491.2.3.1.1.3.2.3
The file name of the software image to be loaded into this device. This object value may optionally contain server and path information about the file name when applicable. If unknown, the string '(unknown)' is returned. This object is shared with docsDevSwFilename.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

ocStbHostFirmwareDownloadFailedStatus 1.3.6.1.4.1.4491.2.3.1.1.3.2.4
This object details the firmware download failed status codes. cdlError1, No Failure cdlError2, Improper code file controls - CVC subject organizationName for manufacturer does not match the Host device manufacturer name cdlError3, Improper code file controls - CVC subject organizationName for code cosigning agent does not match the Host device current code cosigning agent. cdlError4, Improper code file controls - The manufacturer's PKCS #7 signingTime value is equal-to or less-than the codeAccessStart value currently held in the Host device. cdlError5, Improper code file controls - The manufacturer's PKCS #7 validity start time value is less-than the cvcAccessStart value currently held in the Host device. cdlError6, Improper code file controls - The manufacturer's CVC validity start time is less-than the cvcAccessStart value currently held in the Host device. cdlError7, Improper code file controls - The manufacturer's PKCS #7 signingTime value is less-than the CVC validity start time. cdlError8, Improper code file controls - Missing or improper extendedKeyUsage extension in the manufacturer CVC. cdlError9, Improper code file controls - The cosigner's PKCS #7 signingTime value is equal-to or less-than the codeAccessStart value currently held in the Host device. cdlError10, Improper code file controls - The cosigner's PKCS #7 validity start time value is less-than the cvcAccessStart value currently held in the Host device. cdlError11, Improper code file controls - The cosigner's CVC validity start time is less-than the cvcAccessStart value currently held in the Host device. cdlError12, Improper code file controls - The cosigner's PKCS #7 signingTime value is less-than the CVC validity start time. cdlError13, Improper code file controls - Missing or improper extended key-usage extension in the cosigner's CVC. cdlError14, Code file manufacturer CVC validation failure. cdlError15, Code file manufacturer CVS validation failure. cdlError16, Code file cosigner CVC validation failure. cdlError17, Code file cosigner CVS validation failure. cdlError18, Improper eCM configuration file CVC format (e.g., missing or improper key usage attribute). cdlError19, eCM configuration file CVC validation failure. cdlError20, Improper SNMP CVC format. cdlError21, CVC subject organizationName for manufacturer does not match the Host devices manufacturer name. cdlError22, CVC subject organizationName for code cosigning agent does not match the Host devices current code cosigning agent. cdlError23, The CVC validity start time is less-than or equal-to the corresponding subject's cvcAccessStart value currently held in the Host device. cdlError24, Missing or improper key usage attribute. cdlError25, SNMP CVC validation failure.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER cdlError1(1), cdlError2(2), cdlError3(3), cdlError4(4), cdlError5(5), cdlError6(6), cdlError7(7), cdlError8(8), cdlError9(9), cdlError10(10), cdlError11(11), cdlError12(12), cdlError13(13), cdlError14(14), cdlError15(15), cdlError16(16), cdlError17(17), cdlError18(18), cdlError19(19), cdlError20(20), cdlError21(21), cdlError22(22), cdlError23(23), cdlError24(24), cdlError25(25)  

ocStbHostSoftwareApplicationInfoTable 1.3.6.1.4.1.4491.2.3.1.1.3.3.1
This table allows the manager to display and retrieve self-diagnostic software information of all available applications.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OcStbHostSoftwareApplicationInfoEntry

ocStbHostSoftwareApplicationInfoEntry 1.3.6.1.4.1.4491.2.3.1.1.3.3.1.1
An entry exists for each available application.
Status: current Access: not-accessible
OBJECT-TYPE    
  OcStbHostSoftwareApplicationInfoEntry  

ocStbHostSoftwareAppNameString 1.3.6.1.4.1.4491.2.3.1.1.3.3.1.1.1
The application's name string.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

ocStbHostSoftwareAppVersionNumber 1.3.6.1.4.1.4491.2.3.1.1.3.3.1.1.2
The application's version number.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

ocStbHostSoftwareStatus 1.3.6.1.4.1.4491.2.3.1.1.3.3.1.1.3
The software status of the application.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER active(1), inactive(2), downloading(3)  

ocStbHostSoftwareApplicationInfoIndex 1.3.6.1.4.1.4491.2.3.1.1.3.3.1.1.4
Table Index added in this position (4) because it replaced an external index.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..4294967295  

ocStbHostStatus 1.3.6.1.4.1.4491.2.3.1.1.4
OBJECT IDENTIFIER    

ocStbHostPower 1.3.6.1.4.1.4491.2.3.1.1.4.1
OBJECT IDENTIFIER    

ocStbHostPowerStatus 1.3.6.1.4.1.4491.2.3.1.1.4.1.1
Indicates the current power status of the ocStbHost.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER powerOn(1), standby(2)  

ocStbHostAcOutletStatus 1.3.6.1.4.1.4491.2.3.1.1.4.1.2
Indicates the AC accessory power outlet status of the ocStbHost. 'unSwitched' Indicates AC accessory power outlet is present and provides power as long as the ocStbHost is connected to a powered AC outlet. 'switchedOn' Indicates the AC accessory power outlet is currently switched to ON and provides power as long as the value of ocStbHostPowerStatus is 'powerOn'. 'switchedOff' Indicates the AC accessory power outlet is currently switched to OFF and does not provide power. 'notInstalled' Indicates no AC accessory power outlet is present in the ocStbHost.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unSwitched(1), switchedOn(2), switchedOff(3), notInstalled(4)  

ocStbHostUserSettings 1.3.6.1.4.1.4491.2.3.1.1.4.2
OBJECT IDENTIFIER    

ocStbHostUserSettingsPreferedLanguage 1.3.6.1.4.1.4491.2.3.1.1.4.2.1
The preferred language of the audio streams indicated as the 3-octet code specified in ISO 639-2.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(3)  

ocStbHostSystemObjects 1.3.6.1.4.1.4491.2.3.1.1.4.3
OBJECT IDENTIFIER    

ocStbHostSystemTempTable 1.3.6.1.4.1.4491.2.3.1.1.4.3.1
This table contains the temperature sensors of the ocStbHost.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OcStbHostSystemTempEntry

ocStbHostSystemTempEntry 1.3.6.1.4.1.4491.2.3.1.1.4.3.1.1
Conceptual row of a temperature sensor device associated with a Host Resource device (e.g. DVR) of the ocStbHost.
Status: current Access: not-accessible
OBJECT-TYPE    
  OcStbHostSystemTempEntry  

ocStbHostSystemTempIndex 1.3.6.1.4.1.4491.2.3.1.1.4.3.1.1.1
The identifier of the temperature sensor for the corresponding hrDeviceIdx.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..4294967295  

ocStbHostSystemTempDescr 1.3.6.1.4.1.4491.2.3.1.1.4.3.1.1.2
The text containing information about the temperature sensor.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

ocStbHostSystemTempValue 1.3.6.1.4.1.4491.2.3.1.1.4.3.1.1.3
The temperature measured by the sensor. If the temperature sensor does not report a value, this object indicates a value of 0.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

ocStbHostSystemTempLastUpdate 1.3.6.1.4.1.4491.2.3.1.1.4.3.1.1.4
The value of sysUpTime of the last time this value was measured by the ocStbHost. A value 0 means the temperature value is invalid.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

ocStbHostSystemHomeNetworkTable 1.3.6.1.4.1.4491.2.3.1.1.4.3.2
This table contains info about Home Network Clients connected to the ocStbHost.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OcStbHostSystemHomeNetworkEntry

ocStbHostSystemHomeNetworkEntry 1.3.6.1.4.1.4491.2.3.1.1.4.3.2.1
Conceptual row of a Home Network device ocStbHost support/status.
Status: current Access: not-accessible
OBJECT-TYPE    
  OcStbHostSystemHomeNetworkEntry  

ocStbHostSystemHomeNetworkIndex 1.3.6.1.4.1.4491.2.3.1.1.4.3.2.1.1
The identifier of the Home network Client connected to the ocStbHost.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..4294967295  

ocStbHostSystemHomeNetworkMaxClients 1.3.6.1.4.1.4491.2.3.1.1.4.3.2.1.2
Maximum number of clients the Host can support. NOTE: If the Host does not support home network clients, then it SHALL report 0x00.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

ocStbHostSystemHomeNetworkHostDRMStatus 1.3.6.1.4.1.4491.2.3.1.1.4.3.2.1.3
The ocStbHost support for Digital Right Management (DRM).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER hostHasNoDrmCapability(1), hostSupportsDrmButNotForHomeNetworkedClients(2), hostSupportsDrmForItselfAndHomeNetworkedClients(3), reserved(4)  

ocStbHostSystemHomeNetworkConnectedClients 1.3.6.1.4.1.4491.2.3.1.1.4.3.2.1.4
The number of Home Network Clients currently connected to the ocStbHost.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

ocStbHostSystemHomeNetworkClientMacAddress 1.3.6.1.4.1.4491.2.3.1.1.4.3.2.1.5
The MAC address of Home Network Client.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

ocStbHostSystemHomeNetworkClientIpAddress 1.3.6.1.4.1.4491.2.3.1.1.4.3.2.1.6
The Ip address of Home Network Client.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

ocStbHostSystemHomeNetworkClientDRMStatus 1.3.6.1.4.1.4491.2.3.1.1.4.3.2.1.7
The Home Network Clients support for Digital Rights Management (DRM).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

ocStbHostSystemMemoryReportTable 1.3.6.1.4.1.4491.2.3.1.1.4.3.3
This table contains the Id of each memory type reported by the ocStbHost.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OcStbHostSystemMemoryReportEntry

ocStbHostSystemMemoryReportEntry 1.3.6.1.4.1.4491.2.3.1.1.4.3.3.1
Conceptual row of a memory type reported by the ocStbHost.
Status: current Access: not-accessible
OBJECT-TYPE    
  OcStbHostSystemMemoryReportEntry  

ocStbHostSystemMemoryReportIndex 1.3.6.1.4.1.4491.2.3.1.1.4.3.3.1.1
The identifier of the memory type.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..4294967295  

ocStbHostSystemMemoryReportMemoryType 1.3.6.1.4.1.4491.2.3.1.1.4.3.3.1.2
Designates the type of memory that is being reported.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER rom(1), dram(2), sram(3), flash(4), nvm(5), internalHardDriveNoDrmSupport(6), videomemory(7), othermemory(8), reserved(9)  

ocStbHostSystemMemoryReportMemorySize 1.3.6.1.4.1.4491.2.3.1.1.4.3.3.1.3
Designates the physical size of the reported memory type. The units are kilobytes, defined to be 1,024 bytes.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

ocStbCardInfo 1.3.6.1.4.1.4491.2.3.1.1.4.4
OBJECT IDENTIFIER    

ocStbHostCardMacAddress 1.3.6.1.4.1.4491.2.3.1.1.4.4.1
The Mac Address associated with the Card.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

ocStbHostCardIpAddressType 1.3.6.1.4.1.4491.2.3.1.1.4.4.2
The network address Type of ocStbHostCardIpAddress.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

ocStbHostCardIpAddress 1.3.6.1.4.1.4491.2.3.1.1.4.4.3
The network address of the Card.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

ocStbHostCCMMI 1.3.6.1.4.1.4491.2.3.1.1.4.4.5
OBJECT IDENTIFIER    

ocStbHostCCApplications 1.3.6.1.4.1.4491.2.3.1.1.4.4.5.1
OBJECT IDENTIFIER    

ocStbHostCCAppInfoTable 1.3.6.1.4.1.4491.2.3.1.1.4.4.5.1.1
This table allows the manager to retrieve the HTML pages for Card applications retrieved by the Host using the Application Info resource.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OcStbHostCCAppInfoEntry

ocStbHostCCAppInfoEntry 1.3.6.1.4.1.4491.2.3.1.1.4.4.5.1.1.1
The conceptual row for this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  OcStbHostCCAppInfoEntry  

ocStbHostCCAppInfoIndex 1.3.6.1.4.1.4491.2.3.1.1.4.4.5.1.1.1.1
This object was the index for this table in a previous version of the MIB. Currently used only as a placeholder to avoid changing OID values.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

ocStbHostCCApplicationType 1.3.6.1.4.1.4491.2.3.1.1.4.4.5.1.1.1.2
Index for this table. Contains the application_type field in the application_info_cnf() APDU.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..4294967295  

ocStbHostCCApplicationName 1.3.6.1.4.1.4491.2.3.1.1.4.4.5.1.1.1.3
Contains the application name.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

ocStbHostCCApplicationVersion 1.3.6.1.4.1.4491.2.3.1.1.4.4.5.1.1.1.4
Contains the application version.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

ocStbHostCCAppInfoPage 1.3.6.1.4.1.4491.2.3.1.1.4.4.5.1.1.1.5
All HTML data for this application. If a 'page' as reported from the Card contains links, the links shall be traversed, and all HTML from each page traversed shall be included in a single, valid HTML string (with per-page start/end HTML and BODY tags removed). The resulting HTML SHOULD be structured as an HTML table consisting of one column, with one row for each 'page' from the Card. If the full HTML from the application (all pages concatenated) will not fit within the SNMP buffer, text indicating this SHALL follow the table; otherwise nothing except the close BODY and HTML tags SHOULD follow the table.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

ocStbHostInfo 1.3.6.1.4.1.4491.2.3.1.1.4.5
OBJECT IDENTIFIER    

ocStbHostIpAddressType 1.3.6.1.4.1.4491.2.3.1.1.4.5.1
This object was the address type for ocStbHostIpAddress, which was never implemented in a previous version of the MIB. Currently used only as a placeholder to avoid changing OID values.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

ocStbHostIpSubNetMask 1.3.6.1.4.1.4491.2.3.1.1.4.5.2
The IP subnet mask of the Host address.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

ocStbHostRebootInfo 1.3.6.1.4.1.4491.2.3.1.1.4.6
OBJECT IDENTIFIER    

ocStbHostRebootType 1.3.6.1.4.1.4491.2.3.1.1.4.6.1
Describes the type of reboot that occurred the last time the host device rebooted. Unknown(0), unknown reboot. 0 is used as a sentinel value to denote that the reboot reporting mechanism is initialized and ready for use. If it appears in a reboot report as a reboot reason, it means that something (of unknown cause) prevented a reboot reason from being saved. This is a spontaneous reboot. Davic/DOCSIS(1), Davic/DOCSIS switch. The set-top rebooted because the network switched from Davic to DOCSIS or vice versa. This is a controlled reboot. User(2), User reboot. The set-top rebooted at the specific request of the user, typically the MSO, but can also be the subscriber. Includes, but not limited to, headend-initiated reboots, pass-thru and SNMP messages to reboot, new application versions that require a reboot in order to reload, the staging toolkit, hard disk re-format requests, CableCARD inserted or firmware upgrade, and more. This is a controlled reboot. System(3), System reboot. The set-top rebooted because its software determined it cannot continue operation. This can be due to any number of reasons, including: detection of logic errors, exhaustion of various system resources, detection of memory corruption, and more. This is a spontaneous reboot. Trap(4), Trap reboot. A fatal error detected by the CPU. This varies between CPU manufacturers; some possible causes are illegal address references, misaligned instruction or data access, memory protection violations, attempt to decode an unrecognized instruction, etc. This is a spontaneous reboot. Silent or Watchdog(5). Depending on platform, this is either a Silent Reboot (A reboot of unknown origin that reports no information) or a Watchdog reboot. This is a spontaneous reboot. Bootloader(6), Bootloader reboot. For use by bootloader software. This is a spontaneous reboot. PowerUp(7), Power-up reboot. The set-top rebooted because power was lost and then restored. This is a controlled reboot. Upgrade(8), Upgrade Reboot due to loading new resident set-top software. This is a controlled reboot. Hardware(9), Hardware Reset reboot. This depends on the design of a particular set-top. It might be due to a hardware reset line being triggered or by a button push of some kind. Manufacturers sometimes provide a way to hard reset a box besides removing power. This is a spontaneous reboot. CablecardError(10), CablecardError. The Host rebooted because the communication with the CableCARD was lost and could not be reestablished.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(0), davicDocsis(1), user(2), system(3), trap(4), silentWatchdog(5), bootloader(6), powerup(7), hostUpgrade(8), hardware(9), cablecardError(10)  

ocStbHostRebootReset 1.3.6.1.4.1.4491.2.3.1.1.4.6.2
Setting this object to true(1) causes the device to reset, equivalent to a power reset. Reading this object always returns false(2).
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

ocStbHostMemoryInfo 1.3.6.1.4.1.4491.2.3.1.1.4.7
OBJECT IDENTIFIER    

ocStbHostLargestAvailableBlock 1.3.6.1.4.1.4491.2.3.1.1.4.7.1
The largest available continuous block of DRAM available on the host device, in kilobytes.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

ocStbHostTotalVideoMemory 1.3.6.1.4.1.4491.2.3.1.1.4.7.2
The total amount of DRAM dedicated to video decoding and display on the host device, in kilobytes.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

ocStbHostAvailableVideoMemory 1.3.6.1.4.1.4491.2.3.1.1.4.7.3
The total amount of DRAM dedicated to video decoding and display on the host device that is not allocated and available for use, in kilobytes.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

ocStbHostJVMInfo 1.3.6.1.4.1.4491.2.3.1.1.4.8
OBJECT IDENTIFIER    

ocStbHostJVMHeapSize 1.3.6.1.4.1.4491.2.3.1.1.4.8.1
The total amount of DRAM allocated to the Java Virtual Machine heap. The units are kilobytes, defined to be 1,024 bytes.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

ocStbHostJVMAvailHeap 1.3.6.1.4.1.4491.2.3.1.1.4.8.2
The amount of DRAM in the Java Virtual Machine heap that is not allocated and is available for use. The units are kilobytes, defined to be 1,024 bytes.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

ocStbHostJVMLiveObjects 1.3.6.1.4.1.4491.2.3.1.1.4.8.3
The number of active object instances in the Java Virtual Machine that are reachable from running code.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

ocStbHostJVMDeadObjects 1.3.6.1.4.1.4491.2.3.1.1.4.8.4
The number of object instances in the Java Virtual Machine that are NOT reachable from running Code.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

ocStbHostConformance 1.3.6.1.4.1.4491.2.3.1.2
OBJECT IDENTIFIER    

ocStbHostMIBCompliances 1.3.6.1.4.1.4491.2.3.1.2.1
OBJECT IDENTIFIER    

ocStbHostMIBGroups 1.3.6.1.4.1.4491.2.3.1.2.2
OBJECT IDENTIFIER    

ocStbHostMIBCompliance 1.3.6.1.4.1.4491.2.3.1.2.1.1
The requirements for conformance to the OpenCable Set-top HOST MIB.
Status: current Access: read-only
MODULE-COMPLIANCE    

ocStbHostSystemGroup 1.3.6.1.4.1.4491.2.3.1.2.2.1
Defines the objects contained with the ocStbHost System Group.
Status: current Access: read-only
OBJECT-GROUP    

ocStbHostSoftwareGroup 1.3.6.1.4.1.4491.2.3.1.2.2.2
The ocStbHost Software group.
Status: current Access: read-only
OBJECT-GROUP    

ocStbHostStatusGroup 1.3.6.1.4.1.4491.2.3.1.2.2.3
The object group related to multiple ocStbHost status.
Status: current Access: read-only
OBJECT-GROUP    

ocStbHostSecuritySubSystemGroup 1.3.6.1.4.1.4491.2.3.1.2.2.4
The ocStbHost Security Subsystem group.
Status: current Access: read-only
OBJECT-GROUP