NOMADIX-MIB

File: NOMADIX-MIB.mib (288893 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC

Imported symbols

enterprises Counter32 Integer32
IpAddress OBJECT-TYPE NOTIFICATION-TYPE
MODULE-IDENTITY MacAddress RowStatus

Defined Types

DisplayString  
OCTET STRING    

AaaSubCurrTableEntry  
SEQUENCE    
  subIndex Integer32
  subMac DisplayString
  subIp IpAddress
  subPort Integer32
  subName DisplayString
  subBwUp Integer32
  subBwDown Integer32
  subAaaState DisplayString
  subExpiration DisplayString
  subIdleTimeout DisplayString
  subBytesSent Counter32
  subBytesRec Counter32
  subBytesTotal Counter32
  subProxy DisplayString
  subSsid DisplayString
  subStatus RowStatus

AaaAuthSubTableEntry  
SEQUENCE    
  authSubIndex Integer32
  authSubType INTEGER
  authSubDhcpAddrType INTEGER
  authSubDevicePort Integer32
  authSubMac DisplayString
  authSubIp IpAddress
  authSubName DisplayString
  authSubPassword DisplayString
  authSubCountDown INTEGER
  authSubExpTimeHrs Integer32
  authSubExpTimeMins Integer32
  authSubAmtPaid DisplayString
  authSubAmtLeft DisplayString
  authSubUser1 DisplayString
  authSubUser2 DisplayString
  authSubBwUp Integer32
  authSubBwDown Integer32
  authSubConfirmation DisplayString
  authSubStatus RowStatus

AaaLpfStatusTableEntry  
SEQUENCE    
  lpfEntryIndex Integer32
  lpfEntryNickname DisplayString
  lpfEntryOnlineStatus INTEGER

AccessControlIpEntry  
SEQUENCE    
  acIndex Integer32
  acStartAddress IpAddress
  acEndAddress IpAddress
  acStatus RowStatus

DatSessionTableEntry  
SEQUENCE    
  datSubIp IpAddress
  datSubPort Integer32
  datSubMac DisplayString
  datNetIp IpAddress
  datNetPort Integer32
  datDestIp IpAddress
  datDestPort Integer32
  datProto DisplayString
  datSessState DisplayString
  datTimeout Integer32

DhcpPoolTableEntry  
SEQUENCE    
  poolIndex Integer32
  serverIp IpAddress
  netMask IpAddress
  poolStartIp IpAddress
  poolStopIp IpAddress
  leaseMinutes Integer32
  publicPool INTEGER
  ipUpSell INTEGER
  defaultPool INTEGER
  poolStatus RowStatus

DhcpLeaseTableEntry  
SEQUENCE    
  leaseIndex Integer32
  leaseAddress IpAddress
  leaseCLID MacAddress
  leaseStatus INTEGER

INATIpEntry  
SEQUENCE    
  inatIndex Integer32
  inatStartAddress IpAddress
  inatEndAddress IpAddress
  inatEntryStatus RowStatus

LkFeatureListEntry  
SEQUENCE    
  lkFeatureIndex Integer32
  lkFeatureName DisplayString
  lkFeatureStatus INTEGER

PassThroughIPEntry  
SEQUENCE    
  passthroughAddIndex Integer32
  passthroughaddress IpAddress
  statusIP RowStatus

PassThroughDNSEntry  
SEQUENCE    
  passthroughNameIndex Integer32
  passthroughname DisplayString
  statusDNS RowStatus

PortLocConcentratorTableEntry  
SEQUENCE    
  portLocConcIndex Integer32
  portLocAddress IpAddress
  portLocCommunity DisplayString
  portLocUplinkPort Integer32

PortLocTableEntry  
SEQUENCE    
  portLocIndex Integer32
  portLocLocation DisplayString
  portLocPort Integer32
  portLocModemMAC DisplayString
  portLocDescription DisplayString
  portLocState INTEGER

RadProxyUpstreamNasTableEntry  
SEQUENCE    
  nasIndex Integer32
  nasEntryActive INTEGER
  nasIpAddress IpAddress
  nasAuthSec DisplayString
  nasAcctSec DisplayString
  nasDefProf DisplayString
  nasStatus RowStatus

ServiceProfileTableEntry  
SEQUENCE    
  profIndex Integer32
  profName DisplayString
  radAuthOn INTEGER
  radAuthProto INTEGER
  radAuthSrv1Ip IpAddress
  radAuthSrv1Port Integer32
  radAuthSrv1Sec DisplayString
  radAuthSrv2Ip IpAddress
  radAuthSrv2Port Integer32
  radAuthSrv2Sec DisplayString
  radAcctOn INTEGER
  radAcctSrv1Ip IpAddress
  radAcctSrv1Port Integer32
  radAcctSrv1Sec DisplayString
  radAcctSrv2Ip IpAddress
  radAcctSrv2Port Integer32
  radAcctSrv2Sec DisplayString
  radRetrMethod INTEGER
  radRetrFreq Integer32
  radRetrAttempts Integer32
  profStatus RowStatus

TunnelProfileTableEntry  
SEQUENCE    
  tunProfIndex Integer32
  tunProfName DisplayString
  tunPassword DisplayString
  tunPeerIp IpAddress
  tunProfStatus RowStatus

RealmBasedRoutingTableEntry  
SEQUENCE    
  realmIndex Integer32
  realmEntryActive INTEGER
  realmWildcard INTEGER
  realmName DisplayString
  realmMatchType INTEGER
  realmProfile DisplayString
  realmTunProfile DisplayString
  realmStrip INTEGER
  realmTunStrip INTEGER
  realmTunLocHostName DisplayString
  realmStatus RowStatus

SubnetTableEntry  
SEQUENCE    
  subnetIndex Integer32
  subnet IpAddress
  mask IpAddress
  subnetStatus RowStatus

SystemHistoryTableEntry  
SEQUENCE    
  systemHistoryIndex Integer32
  systemHistoryTimestamp DisplayString
  systemHistoryLogin DisplayString
  systemHistoryAddress IpAddress
  systemHistoryMessage DisplayString

SystemSyslogTableEntry  
SEQUENCE    
  systemSyslogIndex Integer32
  systemSyslogTimestamp DisplayString
  systemSyslogVersion DisplayString
  systemSyslogAddress IpAddress
  systemSyslogMessage DisplayString

SystemStaticPortMappingTableEntry  
SEQUENCE    
  systemStaticPortMappingIndex Integer32
  systemStaticPortMappingMAC DisplayString
  systemStaticPortMappingInternalIP IpAddress
  systemStaticPortMappingInternalPort Integer32
  systemStaticPortMappingExternalIP IpAddress
  systemStaticPortMappingExternalPort Integer32
  systemStaticPortMappingRemoteIP IpAddress
  systemStaticPortMappingRemotePort Integer32
  systemStaticPortMappingProto INTEGER
  systemStaticPortMappingStatus RowStatus

UrlFilteringIPTableEntry  
SEQUENCE    
  urlFilteringIPTableIndex Integer32
  urlFilteringIPTableAddress IpAddress
  urlFilteringIPTableStatus RowStatus

UrlFilteringDNSTableEntry  
SEQUENCE    
  urlFilteringDNSTableIndex Integer32
  urlFilteringDNSTableName DisplayString
  urlFilteringDNSTableStatus RowStatus

MacFilteringTableEntry  
SEQUENCE    
  macFilteringTableIndex Integer32
  macFilteringTableAddress MacAddress
  macFilteringStatus RowStatus

WirelessMssidTableEntry  
SEQUENCE    
  mssidIndex Integer32
  mssidName DisplayString
  mssidVlan Integer32
  mssidStatus RowStatus

LocalWebPagesTableEntry  
SEQUENCE    
  localWebPagesTableIndex Integer32
  localWebPagesTableName DisplayString
  localWebPagesTableStatus RowStatus

LocalWebImagesTableEntry  
SEQUENCE    
  localWebImagesTableIndex Integer32
  localWebImagesTableName DisplayString
  localWebImagesTableStatus RowStatus

IpsecPeerTableEntry  
SEQUENCE    
  ipsecPeerIndex Integer32
  ipsecPeerIpAddr IpAddress
  ipsecPeerAuthMethod INTEGER
  ipsecPeerSharedKey DisplayString
  ipsecPeerPrivkeyFile DisplayString
  ipsecPeerCertFile DisplayString
  ipsecPeerEncDesOk INTEGER
  ipsecPeerEnc3DesOk INTEGER
  ipsecPeerHashMd5Ok INTEGER
  ipsecPeerHashShaOk INTEGER
  ipsecPeerKeyStrength INTEGER
  ipsecPeerLifetime Integer32
  ipsecPeerStatus RowStatus

IpsecPolicyTableEntry  
SEQUENCE    
  ipsecPolicyIndex Integer32
  ipsecPolicyPeerIp IpAddress
  ipsecPolicyProtocol INTEGER
  ipsecPolicyRemIp IpAddress
  ipsecPolicyRemSubnet IpAddress
  ipsecPolicyRemPort INTEGER
  ipsecPolicyUseNetIp INTEGER
  ipsecPolicyLocIp IpAddress
  ipsecPolicyLocSubnet IpAddress
  ipsecPolicyLocPort INTEGER
  ipsecPolicyType INTEGER
  ipsecPolicyDirType INTEGER
  ipsecPolicyEncDesOk INTEGER
  ipsecPolicyEnc3desOk INTEGER
  ipsecPolicyEncNullOk INTEGER
  ipsecPolicyAuthMd5Ok INTEGER
  ipsecPolicyAuthShaOk INTEGER
  ipsecPolicyAuthNullOk INTEGER
  ipsecPolicyPfsStrength INTEGER
  ipsecPolicyMaxLifetime Integer32
  ipsecPolicyMaxLifesize Integer32
  ipsecPolicyAutoRenew INTEGER
  ipsecPolicyStatus RowStatus

IpsecSaStatusTableEntry  
SEQUENCE    
  ipsecSaStatusIndex Integer32
  ipsecSaStatusState INTEGER
  ipsecSaStatusStatus RowStatus

Defined Values

nomadix 0.1.3309
MIB definition for Nomadix AG-2000w wireless gateway.
MODULE-IDENTITY    

products 0.1.3309.1
OBJECT IDENTIFIER    

ag 0.1.3309.1.3
OBJECT IDENTIFIER    

aaa 0.1.3309.1.3.2
OBJECT IDENTIFIER    

accessControl 0.1.3309.1.3.4
OBJECT IDENTIFIER    

bandwidthManagement 0.1.3309.1.3.5
OBJECT IDENTIFIER    

billRecMirror 0.1.3309.1.3.6
OBJECT IDENTIFIER    

dat 0.1.3309.1.3.8
OBJECT IDENTIFIER    

dhcp 0.1.3309.1.3.10
OBJECT IDENTIFIER    

dns 0.1.3309.1.3.12
OBJECT IDENTIFIER    

greTunneling 0.1.3309.1.3.13
OBJECT IDENTIFIER    

hpr 0.1.3309.1.3.14
OBJECT IDENTIFIER    

icc 0.1.3309.1.3.16
OBJECT IDENTIFIER    

inat 0.1.3309.1.3.17
OBJECT IDENTIFIER    

licenseKeys 0.1.3309.1.3.18
OBJECT IDENTIFIER    

location 0.1.3309.1.3.19
OBJECT IDENTIFIER    

passthrough 0.1.3309.1.3.24
OBJECT IDENTIFIER    

portLoc 0.1.3309.1.3.28
OBJECT IDENTIFIER    

smtp 0.1.3309.1.3.30
OBJECT IDENTIFIER    

snmpagent 0.1.3309.1.3.32
OBJECT IDENTIFIER    

subsettings 0.1.3309.1.3.33
OBJECT IDENTIFIER    

subnets 0.1.3309.1.3.34
OBJECT IDENTIFIER    

system 0.1.3309.1.3.35
OBJECT IDENTIFIER    

time 0.1.3309.1.3.36
OBJECT IDENTIFIER    

urlFiltering 0.1.3309.1.3.37
OBJECT IDENTIFIER    

radiusProxy 0.1.3309.1.3.38
OBJECT IDENTIFIER    

realmBasedRouter 0.1.3309.1.3.39
OBJECT IDENTIFIER    

sessionlimit 0.1.3309.1.3.40
OBJECT IDENTIFIER    

macFiltering 0.1.3309.1.3.41
OBJECT IDENTIFIER    

tunneling 0.1.3309.1.3.42
OBJECT IDENTIFIER    

wireless 0.1.3309.1.3.43
OBJECT IDENTIFIER    

pppoeClient 0.1.3309.1.3.44
OBJECT IDENTIFIER    

dyndns 0.1.3309.1.3.50
OBJECT IDENTIFIER    

localWeb 0.1.3309.1.3.52
OBJECT IDENTIFIER    

ipsec 0.1.3309.1.3.54
OBJECT IDENTIFIER    

ndxTraps 0.1.3309.1.3.0
OBJECT IDENTIFIER    

aaaOn 0.1.3309.1.3.2.1
Set to 1 to enable AAA, 0 to disable.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaXmlOn 0.1.3309.1.3.2.2
Set to 1 to enable AAA XML Interface, 0 to disable. Note: If trying to set this value returns an error, please check to see if you have a valid license for this feature.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaXmlSender1Ip 0.1.3309.1.3.2.3
IP address of the first server that will send/process XML commands for subscriber management.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

aaaXmlSender2Ip 0.1.3309.1.3.2.22
IP address of the second server that will send/process XML commands for subscriber management.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

aaaMessageNewUserTermsOn 0.1.3309.1.3.2.23
Set to 1 to enable New User Terms of Agreement, 0 to disable.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaMessageNewUserTerms 0.1.3309.1.3.2.24
New User Terms of Agreement.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(400)  

aaaPrintBillingCommandOn 0.1.3309.1.3.2.4
Set to 1 to enable Print Billing Command, 0 to disable.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaPassthroughPortOn 0.1.3309.1.3.2.5
Set to 1 to enable AAA Passthrough Port, 0 to disable.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaPassthroughPortNumber 0.1.3309.1.3.2.6
The port number which is set as passthrough. Must be different from 80, 2111 and 1111.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

aaaDot1xOn 0.1.3309.1.3.2.7
Set to 1 to enable AAA 802.1x Authentication, 0 to disable. Note: 802.1x requires that AAA, RADIUS Authentication and WEP be enabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaOSencodingOn 0.1.3309.1.3.2.8
Set to 1 to enable OS parameter encoding when using Portal Page and EWS, 0 to disable.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaAuthMode 0.1.3309.1.3.2.9
Set to 0 to use Internal Authorization mode, 1 to use External Authorization mode. Note: If trying to set this value returns an error, please check to see if you have a valid license for this feature.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER internalAuthorization(0), externalAuthorization(1)  

aaaInternalAuth 0.1.3309.1.3.2.10
OBJECT IDENTIFIER    

aaaSslOn 0.1.3309.1.3.2.10.1
Set to 1 to enable SSL support, 0 to disable. Please reboot if you change this value.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaSslHostName 0.1.3309.1.3.2.10.2
Specify the certificate DNS name used by SSL
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

aaaPortalPageOn 0.1.3309.1.3.2.10.3
Set to 1 to enable portal page redirection, 0 to disable.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaPortalPageUrl 0.1.3309.1.3.2.10.4
Specify the URL of the portal page web server
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..237)  

aaaUsernameOn 0.1.3309.1.3.2.10.5
Set to 1 to enable username/password, 0 to disable.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaNewSubscriberOn 0.1.3309.1.3.2.10.6
Set to 1 to allow new subscribers, 0 to disable.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaReloginOn 0.1.3309.1.3.2.10.7
Set to 1 to make subscribers relogin after a timeout, 0 to disable.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaCreditCardOn 0.1.3309.1.3.2.10.8
Set to 1 to enable credit card, 0 to disable. Note: If trying to set this value returns an error, please check to see if you have a valid license for this feature.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaCreditCardUrl 0.1.3309.1.3.2.10.9
Specify the URL of the Credit Card Service Server
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..237)  

aaaCreditCardIp 0.1.3309.1.3.2.10.10
The IP address of the Credit Card Service Server
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

aaaMerchantId 0.1.3309.1.3.2.10.11
Specify Merchant ID used for Credit Card Service
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

aaaSmartClientOn 0.1.3309.1.3.2.10.12
Set to 1 to enable Smart client support, 0 to disable. Note: If trying to set this value returns an error, please check to see if you have a valid license for this feature.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaPortalParameterPassing 0.1.3309.1.3.2.10.13
Set to 1 to enable portal parameter passing, 0 to disable.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaPortalPostUrl 0.1.3309.1.3.2.10.14
Specify the URL of the portal XML POST URL
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..237)  

aaaPortalXMLPort 0.1.3309.1.3.2.10.15
Portal XML POST port number.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

aaaSupportGISClients 0.1.3309.1.3.2.10.16
Set to 1 to enable support of GIS clients, 0 to disable.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaIWSLoginPageBlocking 0.1.3309.1.3.2.10.20
Set to 1 to enable blocking of Internal Web Server Login Page , 2 to disable.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

aaaCreditCardServerTypeSelection 0.1.3309.1.3.2.10.21
Setting this value to (1) will select Chainfusion. Setting this value to (2) will select Authorize.net.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER chainfusion(1), authorize-net(2)  

aaaChainfusionCCTransTime 0.1.3309.1.3.2.10.22
The maximum amount of time allowed for a Chainfusion credit card transaction to complete (in minutes).
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

aaaExternalAuth 0.1.3309.1.3.2.11
OBJECT IDENTIFIER    

aaaSecretKey 0.1.3309.1.3.2.11.1
Specify the secret key shared by the NSE and the external server
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

aaaExternalIPAddress 0.1.3309.1.3.2.11.2
Specify external authorization server IP Address.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

aaaAuthorizationUrl 0.1.3309.1.3.2.11.3
Specify external authorization server URL.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..237)  

aaaLoggingOn 0.1.3309.1.3.2.12
Setting this value to (1) will enable logging (via standard SYSLOG) of AAA messages. Setting this value to (0) will disable AAA logging.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaLogNumber 0.1.3309.1.3.2.13
The log number (0-7 of standard SYSLOG) for AAA logging.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..7  

aaaLogFilter 0.1.3309.1.3.2.20
Select the filter level for AAA Logs Available settings: Emergency(0), Alert(1), Critical(2), Error(3), Warning(4), Notice(5), Info(6), Debug(7)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER emergency(0), alert(1), critical(2), error(3), warning(4), notice(5), info(6), debug(7)  

aaaLogServerIp 0.1.3309.1.3.2.14
IP address of the SYSLOG server to receive AAA messages.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

aaaSaveToFile 0.1.3309.1.3.2.21
Setting this value to (1) will enable saving of AAA logs to file. Setting this value to (0) will disable storing of AAA logs in a file.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaBillingOption 0.1.3309.1.3.2.15
OBJECT IDENTIFIER    

aaaBilloptIntroMsg 0.1.3309.1.3.2.15.1
Specify the billing provisioning page intro message
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaBilloptOfferMsg 0.1.3309.1.3.2.15.2
Specify the billing provisioning page offer message
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaBilloptPolicyMsg 0.1.3309.1.3.2.15.3
Specify the billing provisioning page policy message
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaBilloptMinTimeUnitMinute 0.1.3309.1.3.2.15.5
Set the minimum unit (minutes) of time the subscriber can purchase
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

aaaBilloptMinTimeUnitHour 0.1.3309.1.3.2.15.6
Set the minimum unit (hours) of time the subscriber can purchase
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

aaaBilloptMinTimeUnitDay 0.1.3309.1.3.2.15.7
Set the minimum unit (days) of time the subscriber can purchase
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

aaaBilloptMinTimeUnitWeek 0.1.3309.1.3.2.15.8
Set the minimum unit (weeks) of time the subscriber can purchase
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

aaaBilloptMinTimeUnitMonth 0.1.3309.1.3.2.15.9
Set the minimum unit (months) of time the subscriber can purchase
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

aaaBilloptMaxTimeUnitMinute 0.1.3309.1.3.2.15.10
Set the maximum unit (minutes) of time the subscriber can purchase
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

aaaBilloptMaxTimeUnitHour 0.1.3309.1.3.2.15.11
Set the maximum unit (hours) of time the subscriber can purchase
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

aaaBilloptMaxTimeUnitDay 0.1.3309.1.3.2.15.12
Set the maximum unit (days) of time the subscriber can purchase
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

aaaBilloptMaxTimeUnitWeek 0.1.3309.1.3.2.15.13
Set the maximum unit (weeks) of time the subscriber can purchase
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

aaaBilloptMaxTimeUnitMonth 0.1.3309.1.3.2.15.14
Set the maximum unit (months) of time the subscriber can purchase
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

aaaBilloptFreeAccessTime 0.1.3309.1.3.2.15.15
Set default free access time for zero $ billing.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

aaaBilloptMaxSubLifetime 0.1.3309.1.3.2.15.16
Set maximum subscriber lifetime for zero $ billing.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

aaaTaxRate 0.1.3309.1.3.2.15.18
Tax rate, which is to be assessed on all amounts billed by the access gateway. The rate may range from 0 (which means no tax) to 99.99 percent
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..5)  

aaaBillingPlans 0.1.3309.1.3.2.15.19
OBJECT IDENTIFIER    

aaaBillingPlan0 0.1.3309.1.3.2.15.19.1
OBJECT IDENTIFIER    

aaaBillingPlan1 0.1.3309.1.3.2.15.19.2
OBJECT IDENTIFIER    

aaaBillingPlan2 0.1.3309.1.3.2.15.19.3
OBJECT IDENTIFIER    

aaaBillingPlan3 0.1.3309.1.3.2.15.19.4
OBJECT IDENTIFIER    

aaaBillingPlan4 0.1.3309.1.3.2.15.19.5
OBJECT IDENTIFIER    

aaaBillingPlan5 0.1.3309.1.3.2.15.19.6
OBJECT IDENTIFIER    

aaaBillingPlanOn0 0.1.3309.1.3.2.15.19.1.1
Set to 1 to enable billing Plan 0, 0 to disable
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaBillingPlanAssigned0 0.1.3309.1.3.2.15.19.1.2
Set to 1 to assign parameters to billing Plan 0, 0 to disable
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaBillingPlanXoverY0 0.1.3309.1.3.2.15.19.1.3
Set to 1 to assign Plan 0 as XoverY plan, 0 to disable. Please note: to use XoverY billing plan you MUST set the variables aaaBillingPlanCost0, aaaBillingPlanDuration0, and aaaBillingPlanValidity0, to non-zero values prior to enabling the plan (setting aaaBillingPlanXoverY0 = 1). Failure to do so will result in an error on the aaaBillingPlanXoverY0 SNMP Set operation.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaBillingPlanLabel0 0.1.3309.1.3.2.15.19.1.4
Label for billing Plan 0
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..50)  

aaaBillingPlanDesc0 0.1.3309.1.3.2.15.19.1.5
Service Description for billing Plan 0
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..140)  

aaaBillingPlanPricingMin0 0.1.3309.1.3.2.15.19.1.6
Rate Per Minute for billing Plan 0 for Normal Plans
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

aaaBillingPlanPricingHour0 0.1.3309.1.3.2.15.19.1.7
Rate Per hour for billing Plan 0 for Normal Plans
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

aaaBillingPlanPricingDay0 0.1.3309.1.3.2.15.19.1.8
Rate Per day for billing Plan 0 for Normal Plans
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

aaaBillingPlanPricingWeek0 0.1.3309.1.3.2.15.19.1.9
Rate Per week for billing Plan 0 for Normal Plans
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

aaaBillingPlanPricingMonth0 0.1.3309.1.3.2.15.19.1.10
Rate Per Month for billing Plan 0 for Normal Plans
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

aaaBillingPlanBandwidthUp0 0.1.3309.1.3.2.15.19.1.11
Bandwidth Up for billing Plan 0
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..1500  

aaaBillingPlanBandwidthDown0 0.1.3309.1.3.2.15.19.1.12
Bandwidth Down for billing Plan 0
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..1500  

aaaBillingPlanDHCPPool0 0.1.3309.1.3.2.15.19.1.13
DHCP Pool for billing Plan 0: set to 0 for private pool, set to 1 for public pool
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER private(0), public(1)  

aaaBillingPlanRateShow0 0.1.3309.1.3.2.15.19.1.14
Rate Show for billing Plan 0: Set to 0 if the time unit used is set to minutes, 1 if hours, 2 if days, 3 if weeks, and 4 if months.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER minute(0), hour(1), day(2), week(3), month(4)  

aaaBillingPlanCost0 0.1.3309.1.3.2.15.19.1.15
Cost of the XoverY billing Plan 0
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

aaaBillingPlanDuration0 0.1.3309.1.3.2.15.19.1.16
Duration (X) of the XoverY billing Plan 0
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

aaaBillingPlanValidity0 0.1.3309.1.3.2.15.19.1.17
Validity (Y) of the XoverY billing Plan 0
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

aaaBillingPlanValidityRateShow0 0.1.3309.1.3.2.15.19.1.18
Validity Rate Show for XoverY billing Plan 0: Set to 2 if the time unit used is set to days, 3 if weeks, and 4 if months.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER day(2), week(3), month(4)  

aaaBillingPlanOn1 0.1.3309.1.3.2.15.19.2.1
Set to 1 to enable billing Plan 1, 0 to disable
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaBillingPlanAssigned1 0.1.3309.1.3.2.15.19.2.2
Set to 1 to assign parameters to billing Plan 1, 0 to disable
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaBillingPlanXoverY1 0.1.3309.1.3.2.15.19.2.3
Set to 1 to assign Plan 1 as XoverY plan, 0 to disable. Please note: to use XoverY billing plan you MUST set the variables aaaBillingPlanCost1, aaaBillingPlanDuration1, and aaaBillingPlanValidity1, to non-zero values prior to enabling the plan (setting aaaBillingPlanXoverY1 = 1). Failure to do so will result in an error on the aaaBillingPlanXoverY1 SNMP Set operation.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaBillingPlanLabel1 0.1.3309.1.3.2.15.19.2.4
Label for billing Plan 1
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..50)  

aaaBillingPlanDesc1 0.1.3309.1.3.2.15.19.2.5
Service Description for billing Plan 1
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..140)  

aaaBillingPlanPricingMin1 0.1.3309.1.3.2.15.19.2.6
Rate Per Minute for billing Plan 1 for Normal Plans
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

aaaBillingPlanPricingHour1 0.1.3309.1.3.2.15.19.2.7
Rate Per hour for billing Plan 1 for Normal Plans
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

aaaBillingPlanPricingDay1 0.1.3309.1.3.2.15.19.2.8
Rate Per day for billing Plan 1 for Normal Plans
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

aaaBillingPlanPricingWeek1 0.1.3309.1.3.2.15.19.2.9
Rate Per week for billing Plan 1 for Normal Plans
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

aaaBillingPlanPricingMonth1 0.1.3309.1.3.2.15.19.2.10
Rate Per Month for billing Plan 1 for Normal Plans
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

aaaBillingPlanBandwidthUp1 0.1.3309.1.3.2.15.19.2.11
Bandwidth Up for billing Plan 1
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..1500  

aaaBillingPlanBandwidthDown1 0.1.3309.1.3.2.15.19.2.12
Bandwidth Down for billing Plan 1
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..1500  

aaaBillingPlanDHCPPool1 0.1.3309.1.3.2.15.19.2.13
DHCP Pool for billing Plan 1: set to 0 for private pool, set to 1 for public pool
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER private(0), public(1)  

aaaBillingPlanRateShow1 0.1.3309.1.3.2.15.19.2.14
Rate Show for billing Plan 1: Set to 0 if the time unit used is set to minutes, 1 if hours, 2 if days, 3 if weeks, and 4 if months.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER minute(0), hour(1), day(2), week(3), month(4)  

aaaBillingPlanCost1 0.1.3309.1.3.2.15.19.2.15
Cost of the XoverY Plan 1
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

aaaBillingPlanDuration1 0.1.3309.1.3.2.15.19.2.16
Duration (X) of the XoverY Plan 1
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

aaaBillingPlanValidity1 0.1.3309.1.3.2.15.19.2.17
Validity (Y) of the XoverY Plan 1
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

aaaBillingPlanValidityRateShow1 0.1.3309.1.3.2.15.19.2.18
Validity Rate Show for XoverY Plan 1: Set to 2 if the time unit used is set to days, 3 if weeks, and 4 if months.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER day(2), week(3), month(4)  

aaaBillingPlanOn2 0.1.3309.1.3.2.15.19.3.1
Set to 1 to enable billing Plan 2, 0 to disable
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaBillingPlanAssigned2 0.1.3309.1.3.2.15.19.3.2
Set to 1 to assign parameters to billing Plan 2, 0 to disable
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaBillingPlanXoverY2 0.1.3309.1.3.2.15.19.3.3
Set to 1 to assign Plan 2 as XoverY plan, 0 to disable. Please note: to use XoverY billing plan you MUST set the variables aaaBillingPlanCost2, aaaBillingPlanDuration2, and aaaBillingPlanValidity2, to non-zero values prior to enabling the plan (setting aaaBillingPlanXoverY2 = 1). Failure to do so will result in an error on the aaaBillingPlanXoverY2 SNMP Set operation.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaBillingPlanLabel2 0.1.3309.1.3.2.15.19.3.4
Label for billing Plan 2
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..50)  

aaaBillingPlanDesc2 0.1.3309.1.3.2.15.19.3.5
Service Description for billing Plan 2
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..140)  

aaaBillingPlanPricingMin2 0.1.3309.1.3.2.15.19.3.6
Rate Per Minute for billing Plan 2 for Normal Plans
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

aaaBillingPlanPricingHour2 0.1.3309.1.3.2.15.19.3.7
Rate Per hour for billing Plan 2 for Normal Plans
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

aaaBillingPlanPricingDay2 0.1.3309.1.3.2.15.19.3.8
Rate Per day for billing Plan 2 for Normal Plans
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

aaaBillingPlanPricingWeek2 0.1.3309.1.3.2.15.19.3.9
Rate Per week for billing Plan 2 for Normal Plans
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

aaaBillingPlanPricingMonth2 0.1.3309.1.3.2.15.19.3.10
Rate Per Month for billing Plan 2 for Normal Plans
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

aaaBillingPlanBandwidthUp2 0.1.3309.1.3.2.15.19.3.11
Bandwidth Up for billing Plan 2
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..1500  

aaaBillingPlanBandwidthDown2 0.1.3309.1.3.2.15.19.3.12
Bandwidth Down for billing Plan 2
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..1500  

aaaBillingPlanDHCPPool2 0.1.3309.1.3.2.15.19.3.13
DHCP Pool for billing Plan 2: set to 0 for private pool, set to 1 for public pool
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER private(0), public(1)  

aaaBillingPlanRateShow2 0.1.3309.1.3.2.15.19.3.14
Rate Show for billing Plan 2: Set to 0 if the time unit used is set to minutes, 1 if hours, 2 if days, 3 if weeks, and 4 if months.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER minute(0), hour(1), day(2), week(3), month(4)  

aaaBillingPlanCost2 0.1.3309.1.3.2.15.19.3.15
Cost of the XoverY billing Plan 2
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

aaaBillingPlanDuration2 0.1.3309.1.3.2.15.19.3.16
Duration (X) of the XoverY billing Plan 2
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

aaaBillingPlanValidity2 0.1.3309.1.3.2.15.19.3.17
Validity (Y) of the XoverY billing Plan 2
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

aaaBillingPlanValidityRateShow2 0.1.3309.1.3.2.15.19.3.18
Validity Rate Show for XoverY billing Plan 2: Set to 2 if the time unit used is set to days, 3 if weeks, and 4 if months.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER day(2), week(3), month(4)  

aaaBillingPlanOn3 0.1.3309.1.3.2.15.19.4.1
Set to 1 to enable billing Plan 3, 0 to disable
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaBillingPlanAssigned3 0.1.3309.1.3.2.15.19.4.2
Set to 1 to assign parameters to billing Plan 3, 0 to disable
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaBillingPlanXoverY3 0.1.3309.1.3.2.15.19.4.3
Set to 1 to assign Plan 3 as XoverY plan, 0 to disable. Please note: to use XoverY billing plan you MUST set the variables aaaBillingPlanCost3, aaaBillingPlanDuration3, and aaaBillingPlanValidity3, to non-zero values prior to enabling the plan (setting aaaBillingPlanXoverY3 = 1). Failure to do so will result in an error on the aaaBillingPlanXoverY3 SNMP Set operation.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaBillingPlanLabel3 0.1.3309.1.3.2.15.19.4.4
Label for billing Plan 3
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..50)  

aaaBillingPlanDesc3 0.1.3309.1.3.2.15.19.4.5
Service Description for billing Plan 3
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..140)  

aaaBillingPlanPricingMin3 0.1.3309.1.3.2.15.19.4.6
Rate Per Minute for billing Plan 3 for Normal Plans
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

aaaBillingPlanPricingHour3 0.1.3309.1.3.2.15.19.4.7
Rate Per hour for billing Plan 3 for Normal Plans
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

aaaBillingPlanPricingDay3 0.1.3309.1.3.2.15.19.4.8
Rate Per day for billing Plan 3 for Normal Plans
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

aaaBillingPlanPricingWeek3 0.1.3309.1.3.2.15.19.4.9
Rate Per week for billing Plan 3 for Normal Plans
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

aaaBillingPlanPricingMonth3 0.1.3309.1.3.2.15.19.4.10
Rate Per Month for billing Plan 3 for Normal Plans
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

aaaBillingPlanBandwidthUp3 0.1.3309.1.3.2.15.19.4.11
Bandwidth Up for billing Plan 3
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..1500  

aaaBillingPlanBandwidthDown3 0.1.3309.1.3.2.15.19.4.12
Bandwidth Down for billing Plan 3
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..1500  

aaaBillingPlanDHCPPool3 0.1.3309.1.3.2.15.19.4.13
DHCP Pool for billing Plan 3: set to 0 for private pool, set to 1 for public pool
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER private(0), public(1)  

aaaBillingPlanRateShow3 0.1.3309.1.3.2.15.19.4.14
Rate Show for billing Plan 3: Set to 0 if the time unit used is set to minutes, 1 if hours, 2 if days, 3 if weeks, and 4 if months.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER minute(0), hour(1), day(2), week(3), month(4)  

aaaBillingPlanCost3 0.1.3309.1.3.2.15.19.4.15
Cost of the XoverY billing Plan 3
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

aaaBillingPlanDuration3 0.1.3309.1.3.2.15.19.4.16
Duration (X) of the XoverY billing Plan 3
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

aaaBillingPlanValidity3 0.1.3309.1.3.2.15.19.4.17
Validity (Y) of the XoverY billing Plan 3
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

aaaBillingPlanValidityRateShow3 0.1.3309.1.3.2.15.19.4.18
Validity Rate Show for XoverY billing Plan 3: Set to 2 if the time unit used is set to days, 3 if weeks, and 4 if months.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER day(2), week(3), month(4)  

aaaBillingPlanOn4 0.1.3309.1.3.2.15.19.5.1
Set to 1 to enable billing Plan 4, 0 to disable
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaBillingPlanAssigned4 0.1.3309.1.3.2.15.19.5.2
Set to 1 to assign parameters to billing Plan 4, 0 to disable
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaBillingPlanXoverY4 0.1.3309.1.3.2.15.19.5.3
Set to 1 to assign Plan 4 as XoverY plan, 0 to disable. Please note: to use XoverY billing plan you MUST set the variables aaaBillingPlanCost4, aaaBillingPlanDuration4, and aaaBillingPlanValidity4, to non-zero values prior to enabling the plan (setting aaaBillingPlanXoverY4 = 1). Failure to do so will result in an error on the aaaBillingPlanXoverY4 SNMP Set operation.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaBillingPlanLabel4 0.1.3309.1.3.2.15.19.5.4
Label for billing Plan 4
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..50)  

aaaBillingPlanDesc4 0.1.3309.1.3.2.15.19.5.5
Service Description for billing Plan 4
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..140)  

aaaBillingPlanPricingMin4 0.1.3309.1.3.2.15.19.5.6
Rate Per Minute for billing Plan 4 for Normal Plans
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

aaaBillingPlanPricingHour4 0.1.3309.1.3.2.15.19.5.7
Rate Per hour for billing Plan 4 for Normal Plans
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

aaaBillingPlanPricingDay4 0.1.3309.1.3.2.15.19.5.8
Rate Per day for billing Plan 4 for Normal Plans
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

aaaBillingPlanPricingWeek4 0.1.3309.1.3.2.15.19.5.9
Rate Per week for billing Plan 4 for Normal Plans
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

aaaBillingPlanPricingMonth4 0.1.3309.1.3.2.15.19.5.10
Rate Per Month for billing Plan 4 for Normal Plans
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

aaaBillingPlanBandwidthUp4 0.1.3309.1.3.2.15.19.5.11
Bandwidth Up for billing Plan 4
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..1500  

aaaBillingPlanBandwidthDown4 0.1.3309.1.3.2.15.19.5.12
Bandwidth Down for billing Plan 4
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..1500  

aaaBillingPlanDHCPPool4 0.1.3309.1.3.2.15.19.5.13
DHCP Pool for billing Plan 4: set to 0 for private pool, set to 1 for public pool
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER private(0), public(1)  

aaaBillingPlanRateShow4 0.1.3309.1.3.2.15.19.5.14
Rate Show for billing Plan 4: Set to 0 if the time unit used is set to minutes, 1 if hours, 2 if days, 3 if weeks, and 4 if months.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER minute(0), hour(1), day(2), week(3), month(4)  

aaaBillingPlanCost4 0.1.3309.1.3.2.15.19.5.15
Cost of the XoverY billing Plan 4
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

aaaBillingPlanDuration4 0.1.3309.1.3.2.15.19.5.16
Duration (X) of the XoverY billing Plan 4
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

aaaBillingPlanValidity4 0.1.3309.1.3.2.15.19.5.17
Validity (Y) of the XoverY billing Plan 4
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

aaaBillingPlanValidityRateShow4 0.1.3309.1.3.2.15.19.5.18
Validity Rate Show for XoverY billing Plan 4: Set to 2 if the time unit used is set to days, 3 if weeks, and 4 if months.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER day(2), week(3), month(4)  

aaaBillingPlanOn5 0.1.3309.1.3.2.15.19.6.1
Set to 1 to enable billing Plan 5, 0 to disable
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaBillingPlanAssigned5 0.1.3309.1.3.2.15.19.6.2
Set to 1 to assign parameters to billing Plan 5, 0 to disable
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaBillingPlanXoverY5 0.1.3309.1.3.2.15.19.6.3
Set to 1 to assign Plan 5 as XoverY plan, 0 to disable. Please note: to use XoverY billing plan you MUST set the variables aaaBillingPlanCost5, aaaBillingPlanDuration5, and aaaBillingPlanValidity5, to non-zero values prior to enabling the plan (setting aaaBillingPlanXoverY5 = 1). Failure to do so will result in an error on the aaaBillingPlanXoverY5 SNMP Set operation.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaBillingPlanLabel5 0.1.3309.1.3.2.15.19.6.4
Label for billing Plan 5
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..50)  

aaaBillingPlanDesc5 0.1.3309.1.3.2.15.19.6.5
Service Description for billing Plan 5
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..140)  

aaaBillingPlanPricingMin5 0.1.3309.1.3.2.15.19.6.6
Rate Per Minute for billing Plan 5 for Normal Plans
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

aaaBillingPlanPricingHour5 0.1.3309.1.3.2.15.19.6.7
Rate Per hour for billing Plan 5 for Normal Plans
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

aaaBillingPlanPricingDay5 0.1.3309.1.3.2.15.19.6.8
Rate Per day for billing Plan 5 for Normal Plans
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

aaaBillingPlanPricingWeek5 0.1.3309.1.3.2.15.19.6.9
Rate Per week for billing Plan 5 for Normal Plans
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

aaaBillingPlanPricingMonth5 0.1.3309.1.3.2.15.19.6.10
Rate Per Month for billing Plan 5 for Normal Plans
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

aaaBillingPlanBandwidthUp5 0.1.3309.1.3.2.15.19.6.11
Bandwidth Up for billing Plan 5
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..1500  

aaaBillingPlanBandwidthDown5 0.1.3309.1.3.2.15.19.6.12
Bandwidth Down for billing Plan 5
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..1500  

aaaBillingPlanDHCPPool5 0.1.3309.1.3.2.15.19.6.13
DHCP Pool for billing Plan 5: set to 0 for private pool, set to 1 for public pool
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER private(0), public(1)  

aaaBillingPlanRateShow5 0.1.3309.1.3.2.15.19.6.14
Rate Show for billing Plan 5: Set to 0 if the time unit used is set to minutes, 1 if hours, 2 if days, 3 if weeks, and 4 if months.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER minute(0), hour(1), day(2), week(3), month(4)  

aaaBillingPlanCost5 0.1.3309.1.3.2.15.19.6.15
Cost of the XoverY billing Plan 5
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

aaaBillingPlanDuration5 0.1.3309.1.3.2.15.19.6.16
Duration (X) of the XoverY billing Plan 5
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

aaaBillingPlanValidity5 0.1.3309.1.3.2.15.19.6.17
Validity (Y) of the XoverY billing Plan 5
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

aaaBillingPlanValidityRateShow5 0.1.3309.1.3.2.15.19.6.18
Validity Rate Show for XoverY billing Plan 5: Set to 2 if the time unit used is set to days, 3 if weeks, and 4 if months.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER day(2), week(3), month(4)  

aaaSubLoginUI 0.1.3309.1.3.2.16
OBJECT IDENTIFIER    

aaaWebServiceMsg 0.1.3309.1.3.2.16.1
Specify the service selection message
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaWebExistingUserMsg 0.1.3309.1.3.2.16.2
Specify the message for an existing user
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaWebNewUsernameMsg 0.1.3309.1.3.2.16.3
Specify the new username message
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaWebContactMsg 0.1.3309.1.3.2.16.4
Specify the contact message
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaWebMicrosUsernameMsg 0.1.3309.1.3.2.16.5
Specify the PMS username message for MICROS PMS (Maximum length: 140 characters)
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaWebJavascriptOn 0.1.3309.1.3.2.16.6
Set to 1 to enable Javascript, 0 to disable.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaWebRememberMeOn 0.1.3309.1.3.2.16.7
Set to 1 to enable Remember Me browser cookie, 0 to disable.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaRememberMeMsg 0.1.3309.1.3.2.16.8
Specify the Remember Me message
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaRememberMeDays 0.1.3309.1.3.2.16.9
Set the number of days to retain the Remember Me browser cookie
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

aaaCurrency 0.1.3309.1.3.2.16.10
Specify the currency symbol
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..15)  

aaaAmountDecimals 0.1.3309.1.3.2.16.11
Set the number of decimals in the currency
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

aaaWebImage 0.1.3309.1.3.2.16.12
Specify the image file name. Must be rebooted to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..98)  

aaaWebPageBgcolor 0.1.3309.1.3.2.16.13
Specify the background color
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..50)  

aaaWebTabBgcolor 0.1.3309.1.3.2.16.14
Specify the background color for the table
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..98)  

aaaWebTitleFont 0.1.3309.1.3.2.16.15
Specify the title font
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..98)  

aaaWebItemFont 0.1.3309.1.3.2.16.16
Specify the line item font
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..98)  

aaaErrorAccessBlocked 0.1.3309.1.3.2.16.17
AG blocked subscriber access
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaErrorAccessPassword 0.1.3309.1.3.2.16.18
Access to this document requires a password
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaErrorHasOccurred 0.1.3309.1.3.2.16.19
An error has occurred
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaErrorISPChallenge 0.1.3309.1.3.2.16.20
You received a challenge from your Internet Service Provider
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaErrorMinMaxValues 0.1.3309.1.3.2.16.21
This field must contain a number between these two values
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaErrorNoBillingOpts 0.1.3309.1.3.2.16.22
No Billing options are available
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaErrorNotAvailable 0.1.3309.1.3.2.16.23
Internet Service is not available right now. Try again later
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaErrorPasswordMatch 0.1.3309.1.3.2.16.24
The password fields you have entered do not match. Please try again
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaErrorPasswordWrong 0.1.3309.1.3.2.16.25
The password field you have entered is not correct. Please try again
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaErrorRoomBilling 0.1.3309.1.3.2.16.26
Error in Room Billing
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaErrorTooManyUsers 0.1.3309.1.3.2.16.27
Too many subscribers are already logged in. Please try again later
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaErrorTryAgain 0.1.3309.1.3.2.16.28
Try again
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaErrorUserIdMissing 0.1.3309.1.3.2.16.29
The User ID you have entered cannot be found. Please try another
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaErrorUserIdTaken 0.1.3309.1.3.2.16.30
The User ID you have entered is already taken. Please try another
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaErrorWeAreSorry 0.1.3309.1.3.2.16.31
We are sorry
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaErrorWholeNumber 0.1.3309.1.3.2.16.32
This field must contain a whole number value, with no decimals
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaErrorYourAccount 0.1.3309.1.3.2.16.33
Your account was not found. Please check your Username and Password
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaMessageBillingMode 0.1.3309.1.3.2.16.34
Please select the Billing Mode
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaMessagebyCreditCard 0.1.3309.1.3.2.16.35
Bill by Credit Card
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaMessagebyHotelRoom 0.1.3309.1.3.2.16.36
Bill by Hotel Room
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaMessageChooseUsername 0.1.3309.1.3.2.16.37
Choose a User ID (optional)
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaMessageChoosePasswd1 0.1.3309.1.3.2.16.38
Choose a Password (optional)
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaMessageChoosePasswd2 0.1.3309.1.3.2.16.39
Retype the Password (if entered above)
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaMessageFreeInternet 0.1.3309.1.3.2.16.40
Free access to the Internet
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaMessageNewUserLogin 0.1.3309.1.3.2.16.41
Are you a new user? Click this button
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaMessageOldUserLogin 0.1.3309.1.3.2.16.42
Are you an existing user?
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaMessagePurchaseOK1 0.1.3309.1.3.2.16.43
If this is not correct, please go back to the previous page
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaMessagePurchaseOK2 0.1.3309.1.3.2.16.44
and make the necessary changes
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaMessagePurchaseSelect 0.1.3309.1.3.2.16.45
Please select purchase time
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaMessageRequestFailed 0.1.3309.1.3.2.16.49
Your request was declined
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaMessageRequestGranted 0.1.3309.1.3.2.16.50
Your request was successful
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaMessageThankYou 0.1.3309.1.3.2.16.51
Thank you for your business
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaMessageVerifying 0.1.3309.1.3.2.16.52
We are verifying your account. Please wait
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaMessageYourHotel 0.1.3309.1.3.2.16.53
You will be billed directly by your hotel
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaMessageYourPurchase 0.1.3309.1.3.2.16.54
You will be purchasing Internet access with these options
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaPartnerImageOn 0.1.3309.1.3.2.16.55
Setting this value to (1) will enable Partner Image splashscreen. Setting this value to (0) will disable this feature. Note: You must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaPartnerImageFileName 0.1.3309.1.3.2.16.56
File Name of the Partner Image. Note: You must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..32)  

aaaSubPostSession 0.1.3309.1.3.2.17
OBJECT IDENTIFIER    

aaaSubGoodbyePage 0.1.3309.1.3.2.17.1
OBJECT IDENTIFIER    

aaaSubGPEnable 0.1.3309.1.3.2.17.1.1
Enables IWS Goodbye Page
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaSubGPIPAddressOn 0.1.3309.1.3.2.17.1.2
Show IP Address on IWS Goodbye Page
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaSubGPAuthenTypeOn 0.1.3309.1.3.2.17.1.3
Show Authen Type on IWS Goodbye Page
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaSubGPStartTimeOn 0.1.3309.1.3.2.17.1.4
Show Start Time on IWS Goodbye Page
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaSubGPStopTimeOn 0.1.3309.1.3.2.17.1.5
Show Stop Time on IWS Goodbye Page
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaSubGPByteSentOn 0.1.3309.1.3.2.17.1.6
Show Byte Sent on IWS Goodbye Page
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaSubGPByteReceivedOn 0.1.3309.1.3.2.17.1.7
Show Byte Received on IWS Goodbye Page
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaSubGPHyperlinkOn 0.1.3309.1.3.2.17.1.8
Show Hyperlink on IWS Goodbye Page
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  


aaaSubGPSessionSummaryLabel 0.1.3309.1.3.2.17.1.10
Goodbye Page Session Summary Label
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaSubGPSubIPAddressLabel 0.1.3309.1.3.2.17.1.11
Goodbye Page Subscriber IP Address Label
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaSubGPAuthenTypeLabel 0.1.3309.1.3.2.17.1.12
Goodbye Page Subscriber Authen Type Label
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaSubGPStartTimeLabel 0.1.3309.1.3.2.17.1.13
Goodbye Page Start Time Label
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaSubGPStopTimeLabel 0.1.3309.1.3.2.17.1.14
Goodbye Page Stop Time Label
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaSubGPByteSentLabel 0.1.3309.1.3.2.17.1.15
Goodbye Page Byte Sent Label
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaSubGPByteReceivedLabel 0.1.3309.1.3.2.17.1.16
Goodbye Page Byte Received Label
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaSubGPHypertextURLLabel 0.1.3309.1.3.2.17.1.17
Goodbye Page Hypertext URL Label
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..218)  

aaaSubscriber 0.1.3309.1.3.2.18
OBJECT IDENTIFIER    

aaaSubCurrTable 0.1.3309.1.3.2.18.1
List of current subscribers.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AaaSubCurrTableEntry

aaaSubCurrTableEntry 0.1.3309.1.3.2.18.1.1
A subscriber entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  AaaSubCurrTableEntry  

subIndex 0.1.3309.1.3.2.18.1.1.1
Subscriber Index.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

subMac 0.1.3309.1.3.2.18.1.1.2
Physical Address of the Subscriber.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

subIp 0.1.3309.1.3.2.18.1.1.3
IP Address of the Subscriber.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

subPort 0.1.3309.1.3.2.18.1.1.4
Port of the Subscriber.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

subName 0.1.3309.1.3.2.18.1.1.5
Name of the Subscriber.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

subBwUp 0.1.3309.1.3.2.18.1.1.6
Uploading Bandwidth granted to the Subscriber.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

subBwDown 0.1.3309.1.3.2.18.1.1.7
Downloading Bandwidth granted to the Subscriber.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

subAaaState 0.1.3309.1.3.2.18.1.1.8
The AAA state of the Subscriber.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

subExpiration 0.1.3309.1.3.2.18.1.1.9
Expiration Info of the Subscriber.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

subIdleTimeout 0.1.3309.1.3.2.18.1.1.10
Time before the subscriber gets logged off due to inactivity.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

subBytesSent 0.1.3309.1.3.2.18.1.1.11
Bytes sent by the Subscriber, units are MBytes
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

subBytesRec 0.1.3309.1.3.2.18.1.1.12
Bytes received by the Subscriber, units are MBytes
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

subBytesTotal 0.1.3309.1.3.2.18.1.1.13
Total Bytes sent and received by the Subscriber, units are MBytes.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

subProxy 0.1.3309.1.3.2.18.1.1.14
Indicates if the subscriber is proxied or not.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

subSsid 0.1.3309.1.3.2.18.1.1.15
For wireless subscribers this entry shows their SSID.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

subStatus 0.1.3309.1.3.2.18.1.1.16
Status of the Subscriber Current table entry.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

aaaAuthSubTable 0.1.3309.1.3.2.18.2
List of authorized subscribers.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AaaAuthSubTableEntry

aaaAuthSubTableEntry 0.1.3309.1.3.2.18.2.1
A subscriber entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  AaaAuthSubTableEntry  

authSubIndex 0.1.3309.1.3.2.18.2.1.1
Subscriber Index.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

authSubType 0.1.3309.1.3.2.18.2.1.2
Set to 0 if adding a subscriber, to 1 if adding a device.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER subscriber(0), device(1)  

authSubDhcpAddrType 0.1.3309.1.3.2.18.2.1.3
Set to 0 for private pool, set to 1 for public pool. Note: only used if subscriber is configured for DHCP.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER private(0), public(1)  

authSubDevicePort 0.1.3309.1.3.2.18.2.1.4
802.1Q Device Port. Note: only if device and Port-Location is 802.1Q two-ways.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

authSubMac 0.1.3309.1.3.2.18.2.1.5
Physical Address of the subscriber entered in one of the formats: 001122334455, 00-11-22-33-44-55 or 00:11:22:33:44:55. Default value is 00:00:00:00:00:00 if the authSubName is set and authSubMac was not entered yet.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..17)  

authSubIp 0.1.3309.1.3.2.18.2.1.6
IP Address of the subscriber.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

authSubName 0.1.3309.1.3.2.18.2.1.7
Name of the subscriber.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..96)  

authSubPassword 0.1.3309.1.3.2.18.2.1.8
Password of the subscriber.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

authSubCountDown 0.1.3309.1.3.2.18.2.1.9
Set to 1 to enable count-down after login for a subscriber, 0 to disable. Note: username and password should have been entered before, in order to enable this option. Also, expiration time must be entered after enabling this option, in order for it to work properly.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

authSubExpTimeHrs 0.1.3309.1.3.2.18.2.1.10
Expiration time (hours) of the subscriber.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

authSubExpTimeMins 0.1.3309.1.3.2.18.2.1.11
Expiration time (mins) of the subscriber.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..59  

authSubAmtPaid 0.1.3309.1.3.2.18.2.1.12
Amount paid by the subscriber shown in formats: dd.cc or dd. Default is 0.00. Entering dd will result in dd.00. d=dollar, c=cent.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..17)  

authSubAmtLeft 0.1.3309.1.3.2.18.2.1.13
Currency amount left when subscriber who has purchased access moves to a free plan. Formats same as in authSubAmtPaid.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

authSubUser1 0.1.3309.1.3.2.18.2.1.14
Optional field. Used for simple notations about the subscriber.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..15)  

authSubUser2 0.1.3309.1.3.2.18.2.1.15
Optional field. Used for simple notations about the subscriber.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..15)  

authSubBwUp 0.1.3309.1.3.2.18.2.1.16
Uploading Bandwidth granted to the subscriber. Variable in the range from 0 to the max value found in bwmUpWanLinkSpeed. (in kbps)
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

authSubBwDown 0.1.3309.1.3.2.18.2.1.17
Downloading Bandwidth granted to the subscriber. Variable in the range from 0 to the max value found in bwmDownWanLinkSpeed. (in kbps)
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

authSubConfirmation 0.1.3309.1.3.2.18.2.1.18
Confirmation number issued by credit card server.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

authSubStatus 0.1.3309.1.3.2.18.2.1.19
Status of the Authorized Subscriber table entry.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

aaaLoginPageFailover 0.1.3309.1.3.2.25
OBJECT IDENTIFIER    

aaaLoginPageFailoverOn 0.1.3309.1.3.2.25.1
Enables Login Page Failover
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaLpfStatusTable 0.1.3309.1.3.2.25.2
List of External Login Page servers currently being tracked.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AaaLpfStatusTableEntry

aaaLpfStatusTableEntry 0.1.3309.1.3.2.25.2.1
An External Login Page server entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  AaaLpfStatusTableEntry  

lpfEntryIndex 0.1.3309.1.3.2.25.2.1.1
External Login Page server index.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

lpfEntryNickname 0.1.3309.1.3.2.25.2.1.2
Symbolic Name of the Login Page server.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..19)  

lpfEntryOnlineStatus 0.1.3309.1.3.2.25.2.1.3
Status of an External Login Page server.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(0), online(1), offline(2)  

radHistSysloggingOn 0.1.3309.1.3.2.18.3
Setting this value to (1) will enable logging (via standard SYSLOG) of RADIUS packets. Setting this value to (0) will disable RADIUS history logging. (NOTE: Which types of RADIUS packets will be logged is specified using other parameters.)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

radHistSyslogNumber 0.1.3309.1.3.2.18.4
The log number (0-7 of standard SYSLOG) for AAA logging.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..7  

radHistSyslogFilter 0.1.3309.1.3.2.18.8
Select the filter level for RADIUS History Logs Available settings: Emergency(0), Alert(1), Critical(2), Error(3), Warning(4), Notice(5), Info(6), Debug(7)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER emergency(0), alert(1), critical(2), error(3), warning(4), notice(5), info(6), debug(7)  

radHistSyslogServerIp 0.1.3309.1.3.2.18.5
IP address of the SYSLOG server to receive AAA messages.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

radHistSyslogSaveToFile 0.1.3309.1.3.2.18.9
Setting this value to (1) will enable saving of RADIUS History logs to file. Setting this value to (0) will disable storing of AAA logs in a file.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

radProxyAcctHistLog 0.1.3309.1.3.2.18.6
Setting this value to (1) enables the logging of RADIUS Proxy Accounting packets to a logfile on the system flash. Setting it to zero disables such logging and purges the history logfile.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

radProxyAcctHistSyslog 0.1.3309.1.3.2.18.7
If RADIUS History Syslogging is enabled, then setting this value to (1) causes RADIUS Proxy accounting packets to be included in that syslogging. Setting it to zero causes these packets not to be included.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaRadius 0.1.3309.1.3.2.19
OBJECT IDENTIFIER    

aaaRadiusRoutingMode 0.1.3309.1.3.2.19.1
Set to 0 to disable radius client operation. Set to 1 to enable realm-based routing of RADIUS requests. Set to 2 to route all RADIUS requests to the default RADIUS service profile. Note: If trying to set this value returns an error, please check to see if you have a valid license for this feature.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), realm-based(1), fixed(2)  

aaaRadiusDefProf 0.1.3309.1.3.2.19.3
Set the default RADIUS service profile to be used for otherwise un-routeable RADIUS requests. Mandatory if the routing mode is set to fixed. There must be a profile defined with the specified name.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..40)  

aaaRadiusCacheOn 0.1.3309.1.3.2.19.5
Set to 1 to enable radius profile caching, 0 to disable.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaRadiusDefaultIdle 0.1.3309.1.3.2.19.11
Set default timeout for radius subscribers.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

aaaRadiusNasIdOn 0.1.3309.1.3.2.19.12
Set to 1 to Send NAS ID, 0 to disable.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaRadiusNasId 0.1.3309.1.3.2.19.13
Set the NAS Identifier.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

aaaRadiusNasIpOn 0.1.3309.1.3.2.19.14
Set to 1 to Send NAS IP, 0 to disable.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaRadiusNasPortOn 0.1.3309.1.3.2.19.15
Set to 1 to Send NAS Port Type, 0 to disable.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaRadiusNasPortType 0.1.3309.1.3.2.19.16
Set the NAS Port Type.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

aaaRadiusFipOn 0.1.3309.1.3.2.19.17
Set to 1 to Send Frame IP, 0 to disable.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaRadiusRedUrlOn 0.1.3309.1.3.2.19.18
Set to 1 to support URL redirection, 0 to disable.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaRadiusGoodbyeUrlOn 0.1.3309.1.3.2.19.19
Set to 1 to support Goodbye URL redirection, 0 to disable.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaRadiusForgotPasswordUrlOn 0.1.3309.1.3.2.19.20
Set to 1 to support forgot password URL redirection, 0 to disable.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaRadiusForgotPasswordUrl 0.1.3309.1.3.2.19.21
URL of the RADIUS Forgot Password
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..238)  

aaaRadiusSubnetAttrOn 0.1.3309.1.3.2.19.22
Set to 1 to support subnet attribute, 0 to disable.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaRadiusNetVlanOn 0.1.3309.1.3.2.19.23
Set to 1 to enable, 0 to disable RADIUS based WAN VLAN. Note: enabling RADIUS based WAN VLAN will automatically disable SSID based WAN VLAN.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaRadiusNetVlanDefaultOn 0.1.3309.1.3.2.19.24
Set to 1 to enable default 802.1q tag for system traffic, 0 to disable.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

aaaRadiusNetVlanDefaultTag 0.1.3309.1.3.2.19.25
Set the default 802.1q tag for system traffic.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..4094  

aaaRadiusLocalAuthPort 0.1.3309.1.3.2.19.26
Local UDP port for communicating with authentication servers. Must be either 0 or in the range 1024-5000.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

aaaRadiusLocalAcctPort 0.1.3309.1.3.2.19.27
Local UDP port for communicating with accounting servers. Must be either 0 or in the range 1024-5000.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

aaaRadiusLoginRefresh 0.1.3309.1.3.2.19.28
Login refresh time for RADIUS subscribers
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

aaaRadiusTerminationActionOn 0.1.3309.1.3.2.19.29
Set to 1 to support Termination-Action attribute, 0 to disable.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

blockTelnetAccessOn 0.1.3309.1.3.4.1
Set to 1 to enable blocking of all Telnet access, 0 to disable. Note: if set to 1, Telnet access will not be allowed, even from addresses in the access control IP Table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

blockWebAccessOn 0.1.3309.1.3.4.2
Set to 1 to enable blocking of all Web access, 0 to disable. Note: if set to 1, Web access will not be allowed, even from addresses in the access control IP Table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

blockFtpAccessOn 0.1.3309.1.3.4.3
Set to 1 to enable blocking of all FTP access, 0 to disable. Note: if set to 1, FTP access will not be allowed, even from addresses in the access control IP Table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

accessControlOn 0.1.3309.1.3.4.4
Set to 1 to enable Source IP Access Control, 0 to disable. Note: If trying to set this value returns an error, please check to see if you have a valid license for this feature.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

accessControlIpTable 0.1.3309.1.3.4.5
Table of Access Control IPs
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AccessControlIpEntry

accessControlIpEntry 0.1.3309.1.3.4.5.1
Access Control table entry
Status: current Access: not-accessible
OBJECT-TYPE    
  AccessControlIpEntry  

acIndex 0.1.3309.1.3.4.5.1.2
access control table index
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

acStartAddress 0.1.3309.1.3.4.5.1.4
Access Control range Starting IP address
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

acEndAddress 0.1.3309.1.3.4.5.1.6
Access Control range end IP address
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

acStatus 0.1.3309.1.3.4.5.1.7
Status of the Access Control IP Table entry.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

blockSFTPAccessOn 0.1.3309.1.3.4.6
Set to 1 to enable blocking of all SFTP access, 0 to disable. Note: if set to 1, SFTP access will not be allowed, even from addresses in the access control IP Table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

blockSSHShellAccessOn 0.1.3309.1.3.4.7
Set to 1 to enable blocking of all SSH Shell access, 0 to disable. Note: if set to 1, SSH Shell access will not be allowed, even from addresses in the access control IP Table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

bandwidthManagementOn 0.1.3309.1.3.5.1
Set to 1 to enable Bandwidth Management, 0 to disable. Note: If trying to set this value returns an error, please check to see if you have a valid license for this feature. Note: You must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

bwmUpWanLinkSpeed 0.1.3309.1.3.5.3
Uplink Bandwidth through the Network's WAN Link to control using Bandwidth Management. Note: You must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

bwmDownWanLinkSpeed 0.1.3309.1.3.5.5
Downlink Bandwidth through the Network's WAN link to control using Bandwidth Management. Note: You must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

brmMirrorOn 0.1.3309.1.3.6.1
Setting this value to (1) will cause Bill Record Mirroring to be enabled by this unit. Setting this value to (0) will disable Bill Record Mirroring. Note: If trying to set this value returns an error, please check to see if you have a valid license for this feature.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(0)  

brmPropertyId 0.1.3309.1.3.6.2
Id of the Property the unit is installed in
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..32)  

brmNseId 0.1.3309.1.3.6.3
Id of this unit
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..32)  

brmServerIpPrimary 0.1.3309.1.3.6.4
IP Address of the Primary Mirroring Server
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

brmServerUrlPrimary 0.1.3309.1.3.6.5
URL of the Primary Mirroring Server
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..238)  

brmServerSecretPrimary 0.1.3309.1.3.6.6
Secret Key of the Primary Mirroring Server
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

brmServerPortPrimary 0.1.3309.1.3.6.7
Port Number of the Primary Mirroring Server
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

brmServerIpSecondary 0.1.3309.1.3.6.8
IP Address of the Secondary Mirroring Server
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

brmServerUrlSecondary 0.1.3309.1.3.6.9
URL of the Secondary Mirroring Server
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..238)  

brmServerSecretSecondary 0.1.3309.1.3.6.10
Secret Key of the Secondary Mirroring Server
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

brmServerPortSecondary 0.1.3309.1.3.6.11
Port Number of the Secondary Mirroring Server
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

brmServerCCIpOne 0.1.3309.1.3.6.12
IP Address of the First Carbon Copy Server
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

brmServerCCUrlOne 0.1.3309.1.3.6.13
URL of the First Carbon Copy Server
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..238)  

brmServerCCSecretOne 0.1.3309.1.3.6.14
Secret Key of the First Carbon Copy Server
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

brmServerCCPortOne 0.1.3309.1.3.6.15
Port Number of the First Carbon Copy Server
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

brmServerCCIpTwo 0.1.3309.1.3.6.16
IP Address of the Second Carbon Copy Server
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

brmServerCCUrlTwo 0.1.3309.1.3.6.17
URL of the Second Carbon Copy Server
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..238)  

brmServerCCSecretTwo 0.1.3309.1.3.6.18
Secret Key of the Second Carbon Copy Server
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

brmServerCCPortTwo 0.1.3309.1.3.6.19
Port Number of the Second Carbon Copy Server
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

brmServerCCIpThree 0.1.3309.1.3.6.20
IP Address of the Third Carbon Copy Server
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

brmServerCCUrlThree 0.1.3309.1.3.6.21
URL of the Third Carbon Copy Server
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..238)  

brmServerCCSecretThree 0.1.3309.1.3.6.22
Secret Key of the Third Carbon Copy Server
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

brmServerCCPortThree 0.1.3309.1.3.6.23
Port Number of the Third Carbon Copy Server
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

brmRetransMethod 0.1.3309.1.3.6.24
Retransmit Method. Set to (1) for Alternate (round robin) Set to (2) for Do Not Alternate (fail-over)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER alternate(1), notAlternate(2)  

brmRetransAttempts 0.1.3309.1.3.6.25
Number of Retransmit Attempts
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

brmRetransDelay 0.1.3309.1.3.6.26
Retransmit Delay
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

datSessionTable 0.1.3309.1.3.8.1
Current DAT sessions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DatSessionTableEntry

datSessionTableEntry 0.1.3309.1.3.8.1.1
DAT session Entry
Status: current Access: not-accessible
OBJECT-TYPE    
  DatSessionTableEntry  

datSubIp 0.1.3309.1.3.8.1.1.1
IP Address of the Subscriber
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

datSubPort 0.1.3309.1.3.8.1.1.2
Port of the TCP session
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

datSubMac 0.1.3309.1.3.8.1.1.3
MAC Address of the Subscriber
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

datNetIp 0.1.3309.1.3.8.1.1.4
IP address DAT mapped the TCP session to
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

datNetPort 0.1.3309.1.3.8.1.1.5
Port that DAT mapped the TCP session to
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

datDestIp 0.1.3309.1.3.8.1.1.6
IP address of the destination
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

datDestPort 0.1.3309.1.3.8.1.1.7
Port of destination
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

datProto 0.1.3309.1.3.8.1.1.8
Transport Protocol (ICMP, TCP, UDP, etc.)
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

datSessState 0.1.3309.1.3.8.1.1.9
Session State
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

datTimeout 0.1.3309.1.3.8.1.1.10
DAT timeout
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

dhcpDisable 0.1.3309.1.3.10.1
Set to true to disable DHCP services. This variable returns false when one of the DHCP services is enabled through either dhcpIpUpsell, dhcpServerEnable or dhcpRelayEnable. Note: You must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER false(0), true(1)  

dhcpIpUpsell 0.1.3309.1.3.10.2
Set to 0 to disable public IP Upsell service, 1 to enable public IP Upsell. Requires SUBNET to be enabled. Make sure you have a valid license for this feature; otherwise, an error will be returned when trying to set. Please reboot for the changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

dhcpServer 0.1.3309.1.3.10.3
OBJECT IDENTIFIER    

dhcpServerEnable 0.1.3309.1.3.10.3.2
Set to 0 to disable DHCP service, 1 to enable DHCP server. Note: You must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

dhcpServerSubnetBased 0.1.3309.1.3.10.3.3
Set to 0 to disable subnet-based DHCP service, 1 to enable subnet-based DHCP service. Note: You must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

dhcpServerTable 0.1.3309.1.3.10.3.4
Currently active DHCP pools.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DhcpPoolTableEntry

dhcpPoolTableEntry 0.1.3309.1.3.10.3.4.1
Table of DHCP pools
Status: current Access: not-accessible
OBJECT-TYPE    
  DhcpPoolTableEntry  

poolIndex 0.1.3309.1.3.10.3.4.1.2
Lease Table Index
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

serverIp 0.1.3309.1.3.10.3.4.1.4
IP Address to bind to the internal DHCP Server. Note: You must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

netMask 0.1.3309.1.3.10.3.4.1.6
DHCP Server subnet mask. Note: You must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

poolStartIp 0.1.3309.1.3.10.3.4.1.8
Starting IP address of DHCP lease pool. Note: You must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

poolStopIp 0.1.3309.1.3.10.3.4.1.10
Ending IP address of DHCP lease pool. Note: You must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

leaseMinutes 0.1.3309.1.3.10.3.4.1.12
DHCP lease duration in minutes. Note: You must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

publicPool 0.1.3309.1.3.10.3.4.1.14
public IP pool
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER false(0), true(1)  

ipUpSell 0.1.3309.1.3.10.3.4.1.16
IP pool used for IP Upsell
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER false(0), true(1)  

defaultPool 0.1.3309.1.3.10.3.4.1.18
IP pool is the default pool
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER false(0), true(1)  

poolStatus 0.1.3309.1.3.10.3.4.1.20
Status of the DHCP pool table entry.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

dhcpLeaseTable 0.1.3309.1.3.10.3.6
Currently active DHCP leases.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DhcpLeaseTableEntry

dhcpLeaseTableEntry 0.1.3309.1.3.10.3.6.1
Table of DHCP Leases
Status: current Access: not-accessible
OBJECT-TYPE    
  DhcpLeaseTableEntry  

leaseIndex 0.1.3309.1.3.10.3.6.1.2
Lease Table Index
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

leaseAddress 0.1.3309.1.3.10.3.6.1.4
IP Address
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

leaseCLID 0.1.3309.1.3.10.3.6.1.6
Client ID of subscriber to whom lease is assigned
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

leaseStatus 0.1.3309.1.3.10.3.6.1.7
Status of the lease (available or reserved)
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER available(0), reserved(1)  

dhcpRelay 0.1.3309.1.3.10.10
OBJECT IDENTIFIER    

dhcpRelayEnable 0.1.3309.1.3.10.10.2
Set to 0 to disable DHCP Relay service, 1 to enable DHCP Relay service. Note: You must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

dhcpRelayAgentIP 0.1.3309.1.3.10.10.4
IP Address of the Relay Agent. Note: You must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

dhcpRelayServerIP 0.1.3309.1.3.10.10.5
IP Address to which the Relay Agent will forward subscriber DHCP requests. Note: You must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

dnsHostName 0.1.3309.1.3.12.1
DNS Hostname. Note: You must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..64)  

dnsDomain 0.1.3309.1.3.12.2
DNS domain. Note: In order to set this value, DHCP Client must be disabled. Note: You must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..64)  

dnsPrimaryServer 0.1.3309.1.3.12.3
Primary DNS Server. Note: In order to set this value, both DHCP Client and PPPoE Client must be disabled. Note: You must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

dnsSecondaryServer 0.1.3309.1.3.12.4
Secondary DNS Server. Note: In order to set this value, both DHCP Client and PPPoE Client must be disabled. Note: You must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

dnsTertiaryServer 0.1.3309.1.3.12.5
Tertiary DNS Server. Note: You must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

dynDnsEnable 0.1.3309.1.3.50.0
Set to 0 to disable Dynamic DNS, 1 to enable Dynamic DNS
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

dynDnsProtocol 0.1.3309.1.3.50.1
Set to 0 to set protocol to dyndns.org, or set protocol to 1 to set it to dyndns.org (secure) protocol
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER dynDnsOrgProto(0), dynDnsOrgProtoSecure(1)  

dynDnsServer 0.1.3309.1.3.50.2
Server name given by dynamic DNS provider. Please specify only domain name, without http://, '/', etc
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..255)  

dynDnsPort 0.1.3309.1.3.50.3
Set port on which to connect to dynamic dns provider. NOTE: port 443 may only be chosen if protocol is dynDnsOrgProtoSecure (dyndns.org (secure)). For non-secure version of dyndns.org protocol: set to 0 for port 80; set to 1 for port 8245. For secure version: set port to 443
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER dynDnsPort80(0), dynDnsPort8245(1), dynDnsPort443(2)  

dynDnsHostname 0.1.3309.1.3.50.4
Hostname which ip address of the NSE will be mapped to. Please specify only domain name, without http://, '/', etc
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..255)  

dynDnsUsername 0.1.3309.1.3.50.5
Username associated with dynamic dns account
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..255)  

dynDnsPassword 0.1.3309.1.3.50.6
Password associated with dynamic dns account.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..255)  

dynDnsForceUpdate 0.1.3309.1.3.50.7
When set to 1 will perform a forced dynamic DNS update. When set to false will have no effect. Will always return 0 on get. IMPORTANT: some Dynamic DNS Providers (e.g. dyndns.org) consider unnecessary updates (i.e. updates with unchanged IP addresses) abusive. Such updates may result in hostname / username being blocked.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

greTunnelingEnable 0.1.3309.1.3.13.1
Set to 0 to disable GRE Tunneling service, 1 to enable GRE Tunneling service. Note: you must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

greVpnConcentratorIp 0.1.3309.1.3.13.2
IP Address of the VPN Concentrator Server. Note: you must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

greInterfaceIp 0.1.3309.1.3.13.3
IP Address of the GRE Interface on this device. Note: you must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

greInterfaceNetmask 0.1.3309.1.3.13.4
The Subnet Mask for the GRE Interface on this device. Note: you must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

greInterfaceGateway 0.1.3309.1.3.13.5
The Gateway for the GRE Interface on this device. Note: you must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

hprOn 0.1.3309.1.3.14.1
Setting this value to (1) will cause home page redirection to be performed by this unit. Setting this value to (0) will discontinue HPR. Note: If trying to set this value returns an error, please check to see if you have a valid license for this feature.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

hprUrl 0.1.3309.1.3.14.2
The fully qualified WWW URL at which to redirect Home Page Requests.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..237)  

hprParameterPassing 0.1.3309.1.3.14.3
Setting this value to (1) will cause inclusion of parameters with the passed URL during HPR. Setting this value to (0) will discontinue parameter passing.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

hprRedirectionFrequency 0.1.3309.1.3.14.4
The time interval, specified in minutes, after which the next redirection will take place.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

iccOn 0.1.3309.1.3.16.1
Set to (1) to enable the ICC. Set to (0) to disable. Note: If trying to set this value returns an error, please check to see if you have a valid license for this feature.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

iccTitle 0.1.3309.1.3.16.2
The title to appear on the ICC console window
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..237)  

iccLogoutOption 0.1.3309.1.3.16.3
What should the ICC do when a subscriber closes it? 0 to Redisplay, 2 to logout and return the user to a *Pending* state (valid only with RADIUS)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER redisplay(0), logout(2)  

iccLanguageOption 0.1.3309.1.3.16.5
What language would you like to be displayed on the ICC? Available settings: 0=English, 1=Chinese, 2=French, 3=German, 4=Japanese, 5=Spanish, 6=Other. If *other* is selected, please make a selection for iccCharSetOption.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER english(0), chinese(1), french(2), german(3), japanese(4), spanish(5), other(6)  

iccTimerOption 0.1.3309.1.3.16.6
Set to (1) for ICC Elapsed Time. Set to (0) for Time Remaining. Note: If trying to set this value returns an error, please check to see if you have a valid license for this feature.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER remaining(0), elapsed(1)  

iccCharSetOption 0.1.3309.1.3.16.7
This value indicates specific character set to be displayed. In order to set this value, iccLanguageOption should be first set to *other*. Available settings: 0=default, 1=western-iso-8859-1, 2=chinese-big5, 3=chinese-euc-cn, 4=chinese-euc-tw, 5=chinese-gb2312, 6=japanese-euc-jp, 7=japanese-iso-2022-jp, 8=japanese-shift-jis, 9=korean-euc-kr, 10=korean-iso-2022-kr, 11=korean-ks-c-5601.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER default(0), western-iso-8859-1(1), chinese-big5(2), chinese-euc-cn(3), chinese-euc-tw(4), chinese-gb2312(5), japanese-euc-jp(6), japanese-iso-2022-jp(7), japanese-shift-jis(8), korean-euc-kr(9), korean-iso-2022-kr(10), korean-ks-c-5601(11)  

iccButtons 0.1.3309.1.3.16.10
OBJECT IDENTIFIER    

iccISPLogoButton 0.1.3309.1.3.16.10.5
OBJECT IDENTIFIER    

iccButton2 0.1.3309.1.3.16.10.6
OBJECT IDENTIFIER    

iccButton3 0.1.3309.1.3.16.10.7
OBJECT IDENTIFIER    

iccButton4 0.1.3309.1.3.16.10.8
OBJECT IDENTIFIER    

iccButton5 0.1.3309.1.3.16.10.9
OBJECT IDENTIFIER    

iccButton6 0.1.3309.1.3.16.10.10
OBJECT IDENTIFIER    

iccButton7 0.1.3309.1.3.16.10.11
OBJECT IDENTIFIER    

iccButton8 0.1.3309.1.3.16.10.12
OBJECT IDENTIFIER    

iccButton9 0.1.3309.1.3.16.10.13
OBJECT IDENTIFIER    

iccISPLogoButtonName 0.1.3309.1.3.16.10.5.1
ISP Logo Button Name
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..37)  

iccISPLogoButtonURL 0.1.3309.1.3.16.10.5.2
ISP Logo Button URL
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..237)  

iccISPLogoButtonImgName 0.1.3309.1.3.16.10.5.3
ISP Logo Button Image Name
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..31)  

iccButtonName2 0.1.3309.1.3.16.10.6.1
ICC Button 2 Name
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..37)  

iccButtonURL2 0.1.3309.1.3.16.10.6.2
ICC Button 2 URL
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..237)  

iccButtonImgName2 0.1.3309.1.3.16.10.6.3
ICC Button 2 Image Name
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..31)  

iccButtonName3 0.1.3309.1.3.16.10.7.1
ICC Button 3 Name
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..37)  

iccButtonURL3 0.1.3309.1.3.16.10.7.2
ICC Button 3 URL
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..237)  

iccButtonImgName3 0.1.3309.1.3.16.10.7.3
ICC Button 3 Image Name
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..31)  

iccButtonName4 0.1.3309.1.3.16.10.8.1
ICC Button 4 Name
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..37)  

iccButtonURL4 0.1.3309.1.3.16.10.8.2
ICC Button 4 URL
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..237)  

iccButtonImgName4 0.1.3309.1.3.16.10.8.3
ICC Button 4 Image Name
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..31)  

iccButtonName5 0.1.3309.1.3.16.10.9.1
ICC Button 5 Name
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..37)  

iccButtonURL5 0.1.3309.1.3.16.10.9.2
ICC Button 5 URL
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..237)  

iccButtonImgName5 0.1.3309.1.3.16.10.9.3
ICC Button 5 Image Name
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..31)  

iccButtonName6 0.1.3309.1.3.16.10.10.1
ICC Button 6 Name
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..37)  

iccButtonURL6 0.1.3309.1.3.16.10.10.2
ICC Button 6 URL
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..237)  

iccButtonImgName6 0.1.3309.1.3.16.10.10.3
ICC Button 6 Image Name
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..31)  

iccButtonName7 0.1.3309.1.3.16.10.11.1
ICC Button 7 Name
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..37)  

iccButtonURL7 0.1.3309.1.3.16.10.11.2
ICC Button 7 URL
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..237)  

iccButtonImgName7 0.1.3309.1.3.16.10.11.3
ICC Button 7 Image Name
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..31)  

iccButtonName8 0.1.3309.1.3.16.10.12.1
ICC Button 8 Name
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..37)  

iccButtonURL8 0.1.3309.1.3.16.10.12.2
ICC Button 8 URL
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..237)  

iccButtonImgName8 0.1.3309.1.3.16.10.12.3
ICC Button 8 Image Name
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..31)  

iccButtonName9 0.1.3309.1.3.16.10.13.1
ICC Button 9 Name
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..37)  

iccButtonURL9 0.1.3309.1.3.16.10.13.2
ICC Button 9 URL
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..237)  

iccButtonImgName9 0.1.3309.1.3.16.10.13.3
ICC Button 9 Image Name
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..31)  

iccBanners 0.1.3309.1.3.16.14
OBJECT IDENTIFIER    

iccBanner1 0.1.3309.1.3.16.14.14
OBJECT IDENTIFIER    

iccBanner2 0.1.3309.1.3.16.14.15
OBJECT IDENTIFIER    

iccBanner3 0.1.3309.1.3.16.14.16
OBJECT IDENTIFIER    

iccBanner4 0.1.3309.1.3.16.14.17
OBJECT IDENTIFIER    

iccBanner5 0.1.3309.1.3.16.14.18
OBJECT IDENTIFIER    

iccBannerName1 0.1.3309.1.3.16.14.14.1
ICC Banner Name 1
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..15)  

iccBannerURL1 0.1.3309.1.3.16.14.14.2
ICC Banner 1 URL
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..237)  

iccBannerImgName1 0.1.3309.1.3.16.14.14.3
ICC Banner 1 Image Name
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..31)  

iccBannerDuration1 0.1.3309.1.3.16.14.14.4
ICC Banner 1 Duration in seconds. Minimum allowed value is 30.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

iccBannerStartTime1 0.1.3309.1.3.16.14.14.5
Start Time (Optional) {Hour}:{Min}{AM/PM}
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..16)  

iccBannerStopTime1 0.1.3309.1.3.16.14.14.6
Stop Time (Optional) {Hour}:{Min}{AM/PM}
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..16)  

iccBannerName2 0.1.3309.1.3.16.14.15.1
ICC Banner Name 2
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..15)  

iccBannerURL2 0.1.3309.1.3.16.14.15.2
ICC Banner 2 URL
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..237)  

iccBannerImgName2 0.1.3309.1.3.16.14.15.3
ICC Banner 2 Image Name
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..31)  

iccBannerDuration2 0.1.3309.1.3.16.14.15.4
ICC Banner 2 Duration in seconds. Minimum allowed value is 30.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

iccBannerStartTime2 0.1.3309.1.3.16.14.15.5
Start Time (Optional) {Hour}:{Min}{AM/PM}
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..16)  

iccBannerStopTime2 0.1.3309.1.3.16.14.15.6
Stop Time (Optional) {Hour}:{Min}{AM/PM}
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..16)  

iccBannerName3 0.1.3309.1.3.16.14.16.1
ICC Banner Name 3
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..15)  

iccBannerURL3 0.1.3309.1.3.16.14.16.2
ICC Banner 3 URL
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..237)  

iccBannerImgName3 0.1.3309.1.3.16.14.16.3
ICC Banner 3 Image Name
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..31)  

iccBannerDuration3 0.1.3309.1.3.16.14.16.4
ICC Banner 3 Duration in seconds. Minimum allowed value is 30.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

iccBannerStartTime3 0.1.3309.1.3.16.14.16.5
Start Time (Optional) {Hour}:{Min}{AM/PM}
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..16)  

iccBannerStopTime3 0.1.3309.1.3.16.14.16.6
Stop Time (Optional) {Hour}:{Min}{AM/PM}
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..16)  

iccBannerName4 0.1.3309.1.3.16.14.17.1
ICC Banner Name 4
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..15)  

iccBannerURL4 0.1.3309.1.3.16.14.17.2
ICC Banner 4 URL
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..237)  

iccBannerImgName4 0.1.3309.1.3.16.14.17.3
ICC Banner 4 Image Name
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..31)  

iccBannerDuration4 0.1.3309.1.3.16.14.17.4
ICC Banner 4 Duration in seconds. Minimum allowed value is 30.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

iccBannerStartTime4 0.1.3309.1.3.16.14.17.5
Start Time (Optional) {Hour}:{Min}{AM/PM}
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..16)  

iccBannerStopTime4 0.1.3309.1.3.16.14.17.6
Stop Time (Optional) {Hour}:{Min}{AM/PM}
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..16)  

iccBannerName5 0.1.3309.1.3.16.14.18.1
ICC Banner Name 5
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..15)  

iccBannerURL5 0.1.3309.1.3.16.14.18.2
ICC Banner 5 URL
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..237)  

iccBannerImgName5 0.1.3309.1.3.16.14.18.3
ICC Banner 5 Image Name
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..31)  

iccBannerDuration5 0.1.3309.1.3.16.14.18.4
ICC Banner 5 Duration in seconds. Minimum allowed value is 30.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

iccBannerStartTime5 0.1.3309.1.3.16.14.18.5
Start Time (Optional) {Hour}:{Min}{AM/PM}
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..16)  

iccBannerStopTime5 0.1.3309.1.3.16.14.18.6
Stop Time (Optional) {Hour}:{Min}{AM/PM}
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..16)  

inatOn 0.1.3309.1.3.17.1
Set to 1 to enable iNAT, 0 to disable. Valid License is required
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

pptpOn 0.1.3309.1.3.17.2
Set to 1 to enable PPTP, 0 to disable. Valid License is required
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

pptpidOn 0.1.3309.1.3.17.4
Set to 1 to enable PPTP ID support, 0 to disable. Valid PPTP License is required Note: You must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

ipsecOn 0.1.3309.1.3.17.3
Set to 1 to enable subscriber IPSec passthru, 0 to disable. Valid License is required. (NOTE: This is not to be confused with the MIB variable ipsecVpnOn, which pertains to IPSec traffic between the NSE and remote hosts).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

inatIpTable 0.1.3309.1.3.17.5
Table of iNAT IPs
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    INATIpEntry

inatIpEntry 0.1.3309.1.3.17.5.1
iNAT table entry
Status: current Access: not-accessible
OBJECT-TYPE    
  INATIpEntry  

inatIndex 0.1.3309.1.3.17.5.1.2
iNAT table index
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

inatStartAddress 0.1.3309.1.3.17.5.1.4
iNAT range Starting IP address
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

inatEndAddress 0.1.3309.1.3.17.5.1.6
iNAT range end IP address
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

inatEntryStatus 0.1.3309.1.3.17.5.1.10
Status of the iNAT table entry.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

lkKey 0.1.3309.1.3.18.1
License key.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..32)  

lkModelNo 0.1.3309.1.3.18.2
Model number.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..10)  

lkMaxNumSubs 0.1.3309.1.3.18.3
Maximum number of subscribers.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

lkFeatureList 0.1.3309.1.3.18.4
List of features using the license key.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LkFeatureListEntry

lkFeatureListEntry 0.1.3309.1.3.18.4.1
Feature entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  LkFeatureListEntry  

lkFeatureIndex 0.1.3309.1.3.18.4.1.1
license key table index
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

lkFeatureName 0.1.3309.1.3.18.4.1.2
Feature name.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..30)  

lkFeatureStatus 0.1.3309.1.3.18.4.1.3
License status.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notPurchased(0), purchased(1)  

locationCompanyName 0.1.3309.1.3.19.1
Name of the administrator's company.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(2..39)  

locationSiteName 0.1.3309.1.3.19.2
Name of the deployment site.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..39)  

locationAddress1 0.1.3309.1.3.19.3
Physical location - address (line 1).
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..39)  

locationAddress2 0.1.3309.1.3.19.4
Physical location - address (line 2).
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..39)  

locationCity 0.1.3309.1.3.19.5
Physical location - city.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(2..39)  

locationState 0.1.3309.1.3.19.6
Physical location - state.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(2..39)  

locationZip 0.1.3309.1.3.19.7
Physical location - zip.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..39)  

locationCountry 0.1.3309.1.3.19.8
Physical location - country.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(2..39)  

locationEmail 0.1.3309.1.3.19.9
Administrator's e-mail address.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(5..39)  

locationVenueType 0.1.3309.1.3.19.10
This value indicates Venue Type chosen: (1) Apartment (2) Bar/Coffeeshop/Restaurant (3) Convention Center (4) Corporate Guest Access (5) Education (6) Hospitality (7) Marina/camp ground (8) Public Space (9) Public transport (10) Other
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER apartment(1), bar-coffeeshop-restaurant(2), convention-center(3), corporate-guest-access(4), education(5), hospitality(6), marina-camp-ground(7), public-space(8), public-transport(9), other(10)  

locationNetworkIp 0.1.3309.1.3.19.12
The IP Address for the Network side interface. Note: in order to set this value, locationNetIntfCfgMode must be set to static. Note: you must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

locationNetmask 0.1.3309.1.3.19.13
The Subnet Mask for the network side interface. Note: in order to set this value, locationNetIntfCfgMode must be set to static. Note: you must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

locationGateway 0.1.3309.1.3.19.14
The IP Address of the default gateway. Note: in order to set this value, locationNetIntfCfgMode must be set to static. Note: you must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

locationNetIntfCfgMode 0.1.3309.1.3.19.15
Setting this value to (0) will use statically configured IP address. Setting to (1) will enable DHCP Client for the system. Setting to (2) will enable PPPoE Client for the system. Note: you must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER static(0), dhcpClient(1), pppoeClient(2)  

locationIsoCountryCode 0.1.3309.1.3.19.16
ISO Country Code
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..3)  

locationPhoneCountryCode 0.1.3309.1.3.19.17
Phone Country Code
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..10)  

locationCallingAreaCode 0.1.3309.1.3.19.18
Calling Area Code
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..10)  

locationNetworkSsidZone 0.1.3309.1.3.19.19
Network SSID/ZONE
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

passthroughOn 0.1.3309.1.3.24.1
Setting this value to (1) will enable Passthrough Addresses feature. Setting this value to (0) will disable it. Note: If trying to set this value returns an error, please check to see if you have a valid license for this feature.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

passthroughIPTable 0.1.3309.1.3.24.2
Host passthrough table for IP addresses
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PassThroughIPEntry

passthroughIPEntry 0.1.3309.1.3.24.2.1
passthrough table entry
Status: current Access: not-accessible
OBJECT-TYPE    
  PassThroughIPEntry  

passthroughAddIndex 0.1.3309.1.3.24.2.1.1
Passthrough Address Table Index
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

passthroughaddress 0.1.3309.1.3.24.2.1.2
The packets destined for this IP address are passed through without authentication, authorization.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

statusIP 0.1.3309.1.3.24.2.1.3
Status of the Passthrough IP table entry.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

passthroughDNSTable 0.1.3309.1.3.24.3
Host passthrough table for DNS names
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PassThroughDNSEntry

passthroughDNSEntry 0.1.3309.1.3.24.3.1
passthrough table entry
Status: current Access: not-accessible
OBJECT-TYPE    
  PassThroughDNSEntry  

passthroughNameIndex 0.1.3309.1.3.24.3.1.1
Passthrough Name Table Index
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

passthroughname 0.1.3309.1.3.24.3.1.2
The packets destined for this DNS name are passed through without authentication, authorization.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..237)  

statusDNS 0.1.3309.1.3.24.3.1.3
Status of the Passthrough DNS table entry.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

portLocInRoomPortMappingOn 0.1.3309.1.3.28.1
Setting this value to (1) will enable In Room Port Mapping feature. Setting this value to (0) will disable this feature. Note: If trying to set this value returns an error, please check to see if you have a valid license for this feature.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

portLocInRoomPortMappingUsername 0.1.3309.1.3.28.2
Username needed when performing In Room Port Mapping. (Maximum length: 17 characters)
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..17)  

portLocInRoomPortMappingPassword 0.1.3309.1.3.28.3
Password needed when performing In Room Port Mapping.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..17)  

portLocConcentratorType 0.1.3309.1.3.28.4
Setting this value to (0) will indicate that no concentrator will be used. Entering (1) will mean the device which understands 802.1Q VLAN IDs one-way will be used, while (2) will indicate the device which understands 802.1Q VLAN IDs two-ways. Entering (3) to (8) will indicate that one of the following access concentrators will be exploited: (3) Tut Systems Expresso, (4) Lucent DSL Terminator, (5) Tut MDU Lite Systems, (6) any RFC1493 Compliant System, (7) RiverDelta 1000B, (8) Elastic Networks.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER no(0), vlan1(1), vlan2(2), expresso(3), lucent(4), mdulite(5), rfc1493(6), riverdelta(7), elastic(8)  

portLocConcentratorTable 0.1.3309.1.3.28.10
List of IP addresses, SNMP community names, and uplink ports for each concentrator.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PortLocConcentratorTableEntry

portLocConcentratorTableEntry 0.1.3309.1.3.28.10.1
Concentrator table entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  PortLocConcentratorTableEntry  

portLocConcIndex 0.1.3309.1.3.28.10.1.2
Port-location Concentrator Table Index.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

portLocAddress 0.1.3309.1.3.28.10.1.4
IP Address of the concentrator.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

portLocCommunity 0.1.3309.1.3.28.10.1.6
SNMP community name of the concentrator.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..139)  

portLocUplinkPort 0.1.3309.1.3.28.10.1.8
Uplink port of the concentrator.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

portLocTable 0.1.3309.1.3.28.12
Port-location Table maps ports to rooms
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PortLocTableEntry

portLocTableEntry 0.1.3309.1.3.28.12.1
One entry of the port-location table
Status: current Access: not-accessible
OBJECT-TYPE    
  PortLocTableEntry  

portLocIndex 0.1.3309.1.3.28.12.1.1
Port-location Table Index
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

portLocLocation 0.1.3309.1.3.28.12.1.2
Location description of the entry
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..139)  

portLocPort 0.1.3309.1.3.28.12.1.3
Port of the concentrator this room is connected to
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

portLocModemMAC 0.1.3309.1.3.28.12.1.4
MAC Address of the Modem this room has (valid for Riverdelta and similar concentrators only)
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

portLocDescription 0.1.3309.1.3.28.12.1.5
Description of the Location/Port
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..139)  

portLocState 0.1.3309.1.3.28.12.1.6
Billing/Access State of the port-location
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER noCharge(0), charge(1), blocked(2)  

radProxyServices 0.1.3309.1.3.38.1
Setting this value to (1) enables RADIUS proxy services. Setting it to zero disables RADIUS proxy services.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

radProxyAuthSvrPort 0.1.3309.1.3.38.2
The UDP port number on which RADIUS authentication requests will be received. Setting this value to (0) disables RADIUS authentication proxy services.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

radProxyAcctSvrPort 0.1.3309.1.3.38.3
The UDP port number on which RADIUS accounting requests will be received. Setting this value to (0) disables RADIUS accounting proxy services.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

radProxyLocalServcomPort 0.1.3309.1.3.38.5
Local UDP port for communicating with downstream servers. Must be either 0 or in the range 1024-5000.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

radProxyUpstreamNas 0.1.3309.1.3.38.4
OBJECT IDENTIFIER    

radProxyUpstreamNasTable 0.1.3309.1.3.38.4.1
List of Upstream NASes.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RadProxyUpstreamNasTableEntry

radProxyUpstreamNasTableEntry 0.1.3309.1.3.38.4.1.1
An upstream NAS entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  RadProxyUpstreamNasTableEntry  

nasIndex 0.1.3309.1.3.38.4.1.1.1
Upstream NAS Index
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

nasEntryActive 0.1.3309.1.3.38.4.1.1.2
Indicates whether or not this NAS is active. Requests from inactive NASes won't be processed
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER inactive(0), active(1)  

nasIpAddress 0.1.3309.1.3.38.4.1.1.3
IP Address of the upstream NAS.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

nasAuthSec 0.1.3309.1.3.38.4.1.1.4
The secret key, shared with the upstream NAS, used for authentication packets.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..130)  

nasAcctSec 0.1.3309.1.3.38.4.1.1.5
The secret key, shared with the upstream NAS, used for accounting packets.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..130)  

nasDefProf 0.1.3309.1.3.38.4.1.1.6
(Optional) The name of the RADIUS service profile to handle requests from this upstream NAS if realm-basd routing fails. If not present, such packets will be discarded.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..40)  

nasStatus 0.1.3309.1.3.38.4.1.1.7
Status of the upstream NAS table entry.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

rBserviceProfiles 0.1.3309.1.3.39.1
OBJECT IDENTIFIER    

serviceProfileTable 0.1.3309.1.3.39.1.1
List of service profiles
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ServiceProfileTableEntry

serviceProfileTableEntry 0.1.3309.1.3.39.1.1.1
An entry in the list of service profiles.
Status: current Access: not-accessible
OBJECT-TYPE    
  ServiceProfileTableEntry  

profIndex 0.1.3309.1.3.39.1.1.1.1
Service Profile Index
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

profName 0.1.3309.1.3.39.1.1.1.2
The name of this service profile. Must be unique.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..40)  

radAuthOn 0.1.3309.1.3.39.1.1.1.3
Set to 1 to enable radius authentication for this profile, 0 to disable.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

radAuthProto 0.1.3309.1.3.39.1.1.1.4
Radius authentication protocol: rad-auth-proto-pap(0) - PAP rad-auth-proto-chap(1) - CHAP-MD5 rad-auth-proto-mschap-v1(2) - MS-CHAP v1 rad-auth-proto-mschap-v2(3) - MS-CHAP v2
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER rad-auth-proto-pap(0), rad-auth-proto-chap(1), rad-auth-proto-mschap-v1(2), rad-auth-proto-mschap-v2(3)  

radAuthSrv1Ip 0.1.3309.1.3.39.1.1.1.5
IP address of the Primary Radius Authentication Server for this profile.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

radAuthSrv1Port 0.1.3309.1.3.39.1.1.1.6
Port of the Primary Radius Authentication Server for this profile.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

radAuthSrv1Sec 0.1.3309.1.3.39.1.1.1.7
Secret Key of the Primary Radius Authentication Server for this profile.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..130)  

radAuthSrv2Ip 0.1.3309.1.3.39.1.1.1.8
IP address of the Secondary Radius Authentication Server for this profile.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

radAuthSrv2Port 0.1.3309.1.3.39.1.1.1.9
Port of the Secondary Radius Authentication Server for this profile.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

radAuthSrv2Sec 0.1.3309.1.3.39.1.1.1.10
Secret Key of the Secondary Radius Authentication Server for this profile.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..130)  

radAcctOn 0.1.3309.1.3.39.1.1.1.11
Set to 1 to enable radius accounting for this profile, 0 to disable.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

radAcctSrv1Ip 0.1.3309.1.3.39.1.1.1.12
IP address of the Primary Radius Accounting Server for this profile.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

radAcctSrv1Port 0.1.3309.1.3.39.1.1.1.13
Port of the Primary Radius Accounting Server for this profile.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

radAcctSrv1Sec 0.1.3309.1.3.39.1.1.1.14
Secret Key of the Primary Radius Accounting Server for this profile.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..130)  

radAcctSrv2Ip 0.1.3309.1.3.39.1.1.1.15
IP address of the Secondary Radius Accounting Server for this profile.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

radAcctSrv2Port 0.1.3309.1.3.39.1.1.1.16
Port of the Secondary Radius Accounting Server for this profile.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

radAcctSrv2Sec 0.1.3309.1.3.39.1.1.1.17
Secret Key of the Secondary Radius Accounting Server for this profile.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..130)  

radRetrMethod 0.1.3309.1.3.39.1.1.1.18
Set to 0 if the retransmission method is failover, 1 if round-robin.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER failover(0), round-robin(1)  

radRetrFreq 0.1.3309.1.3.39.1.1.1.19
Set the frequency of retransmission (per second).
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

radRetrAttempts 0.1.3309.1.3.39.1.1.1.20
Set the number of retransmissions.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

profStatus 0.1.3309.1.3.39.1.1.1.21
Status of the service profile table entry.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

rBtunnelProfiles 0.1.3309.1.3.39.3
OBJECT IDENTIFIER    

tunnelProfileTable 0.1.3309.1.3.39.3.1
List of tunnel profiles
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TunnelProfileTableEntry

tunnelProfileTableEntry 0.1.3309.1.3.39.3.1.1
An entry in the list of tunnel profiles.
Status: current Access: not-accessible
OBJECT-TYPE    
  TunnelProfileTableEntry  

tunProfIndex 0.1.3309.1.3.39.3.1.1.2
Tunnel Profile Index
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

tunProfName 0.1.3309.1.3.39.3.1.1.4
The name of this tunnel profile. Must be unique.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..40)  

tunPassword 0.1.3309.1.3.39.3.1.1.6
The tunnel password.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..64)  

tunPeerIp 0.1.3309.1.3.39.3.1.1.8
IP address of the tunnel peer for this tunnel.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

tunProfStatus 0.1.3309.1.3.39.3.1.1.20
Status of the tunnel profile table entry.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

rBroutes 0.1.3309.1.3.39.2
OBJECT IDENTIFIER    

realmBasedRoutingTable 0.1.3309.1.3.39.2.1
List of realm-based routes
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RealmBasedRoutingTableEntry

realmBasedRoutingTableEntry 0.1.3309.1.3.39.2.1.1
An entry in the list of realm-based routes.
Status: current Access: not-accessible
OBJECT-TYPE    
  RealmBasedRoutingTableEntry  

realmIndex 0.1.3309.1.3.39.2.1.1.1
realm-based route Index
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

realmEntryActive 0.1.3309.1.3.39.2.1.1.2
Indicates whether or not this route is active.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER inactive(0), active(1)  

realmWildcard 0.1.3309.1.3.39.2.1.1.3
Indicates whether or not this route will match all realm-names or a single, specific realm-name.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

realmName 0.1.3309.1.3.39.2.1.1.4
If this route is for a specific realm, this is the name of that realm.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..80)  

realmMatchType 0.1.3309.1.3.39.2.1.1.5
Indicates whether this policy pertains to prefix realms, suffix realms, or to both.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER prefixOnly(0), suffixOnly(1), prefixOrSuffix(2)  

realmProfile 0.1.3309.1.3.39.2.1.1.6
The RADIUS service profile to which this policy will route.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..40)  

realmTunProfile 0.1.3309.1.3.39.2.1.1.9
The tunnel profile to which this policy will route.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..40)  

realmStrip 0.1.3309.1.3.39.2.1.1.7
Indicates whether or not realm-names should be stripped from user names before sending the username to a RADIUS server.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER dontStrip(0), strip(1)  

realmTunStrip 0.1.3309.1.3.39.2.1.1.10
Indicates whether or not realm-names should be stripped from user names before sending the username to a tunnel server (LNS).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER dontStrip(0), strip(1)  

realmTunLocHostName 0.1.3309.1.3.39.2.1.1.11
Local host name fopr purposes of tunnels, whether profile-triggerred or RADIUS-triggerred
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..40)  

realmStatus 0.1.3309.1.3.39.2.1.1.8
Status of the realm-based routing table entry.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

sessionLimitEnable 0.1.3309.1.3.40.1
Enable/Disable sesstion rate limiting capability
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

sessionLimitMeanRate 0.1.3309.1.3.40.2
This value indicates the session rate limiting mean rate. THE VALUE MUST BE LESS THAN the session rate limiting burst size.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

sessionLimitBurstSize 0.1.3309.1.3.40.3
This value indicates the session rate burst size. THE VALUE MUST BE LARGER THAN the session rate limiting mean rate
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

sessionLimitTimeInterval 0.1.3309.1.3.40.4
This value indicates the session rate time interval.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

sessionLimitFilterOffendersEnable 0.1.3309.1.3.40.5
Enable/Disable adding users who exceed prescribed rate to MAC Filtering
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

smtpRedirect 0.1.3309.1.3.30.1
Setting this value to (1) enables SMTP redirection for misconfigured subscribers. Setting this value to (0) disables SMTP redirection for misconfigured subscribers. (NOTE: Setting it to (0) also sets it to (0) for properly configureds).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

smtpServerIP 0.1.3309.1.3.30.2
The IP address of the SMTP server to redirect all SMTP messages to.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

smtpPcRedirect 0.1.3309.1.3.30.3
Setting this value to (1) enables SMTP redirection for properly configured subscribers. Setting this value to (0) disables SMTP redirection for properly configured subscribers. (NOTE: Setting it to (1) also sets it to (1) for mis-configureds).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

smtpUsername 0.1.3309.1.3.30.4
For SMTP servers which support login authentication, enter valid username for an account on that server. NOTE: Length of username should be shortest allowed by SMTP server. Clients with shorter username may not be able to send e-mail.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..39)  

smtpPassword 0.1.3309.1.3.30.5
For SMTP servers which support login authentication, enter valid password for an account on that server. NOTE: Length of username should be shortest allowed by SMTP server. Clients with shorter password may not be able to send e-mail.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..39)  

smtpServerDNS 0.1.3309.1.3.30.6
The DNS name of the SMTP server to redirect all SMTP messages to. If this field is set, then smtpServerIP will also be updated to reflect the resolved IP address of the DNS name.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..238)  

snmpdOn 0.1.3309.1.3.32.1
Set to 1 to enable SNMP, 0 to disable. Note: If trying to set this value returns an error, please check to see if you have a valid license for this feature. Note: You must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

systemContact 0.1.3309.1.3.32.2
System contact person. Note: You must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..238)  

systemLocation 0.1.3309.1.3.32.3
Physical location of this device. Note: You must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..238)  

getCommunity 0.1.3309.1.3.32.4
Get community string. Note: You must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..238)  

setCommunity 0.1.3309.1.3.32.5
Set community string. Note: You must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..238)  

trapCommunity 0.1.3309.1.3.32.6
Trap community string. Note: You must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..238)  

trapIP 0.1.3309.1.3.32.7
IP address of host to which to send traps. Note: You must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

subnetTable 0.1.3309.1.3.34.1
Currently active public subnets.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SubnetTableEntry

subnetTableEntry 0.1.3309.1.3.34.1.1
Table of Public Subnets
Status: current Access: not-accessible
OBJECT-TYPE    
  SubnetTableEntry  

subnetIndex 0.1.3309.1.3.34.1.1.1
Subnet Table Index
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

subnet 0.1.3309.1.3.34.1.1.2
Subnet
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

mask 0.1.3309.1.3.34.1.1.3
Subnet mask
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

subnetStatus 0.1.3309.1.3.34.1.1.4
Status of the public subnet table entry.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

subIdleLogoutTimeout 0.1.3309.1.3.33.1
Time (in seconds), after which subscriber is logged out. Does not apply to subscribers logged in via RADIUS. Valid values are from 300 to 86400 seconds
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 300..86400  

subToSubCommBlock 0.1.3309.1.3.33.2
When enabled, this feature will prevent wireless subscribers from communicating with one another. When communications blocking is disabled, subscribers will be allowed to communicate
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

systemLoggingOn 0.1.3309.1.3.35.1
Setting this value to (1) will enable logging (via standard SYSLOG) of system messages. Setting this value to (0) will disable system logging.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

systemLogNumber 0.1.3309.1.3.35.2
The log number (0-7 of standard SYSLOG) for system logging.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..7  

systemLogFilter 0.1.3309.1.3.35.3
Select the filter level for SYSTEM Logs Available settings: Emergency(0), Alert(1), Critical(2), Error(3), Warning(4), Notice(5), Info(6), Debug(7)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER emergency(0), alert(1), critical(2), error(3), warning(4), notice(5), info(6), debug(7)  

systemLogServerIp 0.1.3309.1.3.35.4
IP address of the SYSLOG server to receive system messages.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

systemSaveToFile 0.1.3309.1.3.35.5
Setting this value to (1) will enable saving of SYSTEM logs to file. Setting this value to (0) will disable storing of SYSTEM logs in a file.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

systemReportLoggingOn 0.1.3309.1.3.35.6
Setting this value to (1) will enable logging (via standard SYSLOG) of SYSTEM REPORT messages. Setting this value to (0) will disable SYSTEM REPORT logging.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

systemReportLogNumber 0.1.3309.1.3.35.7
The log number (0-7 of standard SYSLOG) for SYSTEM REPORT logging.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..7  

systemReportLogServerIp 0.1.3309.1.3.35.8
IP address of the SYSLOG server to receive SYSTEM REPORT log messages.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

systemReportLogInterval 0.1.3309.1.3.35.9
Interval (in minutes) with which SYSTEM REPORT log messages are sent
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..99999  

systemVersion 0.1.3309.1.3.35.10
Version of the unit, includes model and software version.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..32)  

systemNseId 0.1.3309.1.3.35.11
ID of the unit.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..32)  

systemReboot 0.1.3309.1.3.35.12
Setting this value to (1) will cause the operating system to reboot.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER reboot(1)  

systemBridgeMode 0.1.3309.1.3.35.13
Setting this value to (1) will enable bridge mode. Setting this value to (0) will disable bridge mode. Note: If trying to set this value returns an error, please check to see if you have a valid license for this feature.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

systemConfigFile 0.1.3309.1.3.35.14
Setting this value to (1) will restore the factory configuration settings. Setting this value to (2) will export the current configuration to an archive file. Setting this value to (3) will restore settings from the most recent archive file, if one exists.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER factory(1), export(2), import(3)  

systemConfigFileStatus 0.1.3309.1.3.35.15
This value indicates the status of systemConfigFile set query. (0) - no error occurred, (1) - error occurred, current settings were not changed, (2) - error occurred, current settings may have been corrupted, (3) - error occurred, current settings were not archived.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER noError(0), errorCurrentNotChanged(1), errorCurrentMaybeCorrupted(2), errorCurrentNotArchived(3)  

systemAdminConcurrencyOn 0.1.3309.1.3.35.16
Setting this value to (1) will enable Admin Interface Concurrency enforcement. Setting this value to (0) will disable Concurrency enforcement. Note: If trying to set this value returns an error, please check to see if you have a valid license for this feature.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

systemUptime 0.1.3309.1.3.35.17
Uptime of the unit
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..64)  

systemHistoryTable 0.1.3309.1.3.35.18
List of last 500 access/reboot history entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SystemHistoryTableEntry

systemHistoryTableEntry 0.1.3309.1.3.35.18.1
Access/reboot history table entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  SystemHistoryTableEntry  

systemHistoryIndex 0.1.3309.1.3.35.18.1.1
Access/reboot history table index.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

systemHistoryTimestamp 0.1.3309.1.3.35.18.1.2
Time when access occurred.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(24)  

systemHistoryLogin 0.1.3309.1.3.35.18.1.3
Login name of the user who generated access.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..14)  

systemHistoryAddress 0.1.3309.1.3.35.18.1.4
IP Address of the machine from which access was made.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

systemHistoryMessage 0.1.3309.1.3.35.18.1.5
Type of access occurred.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..429)  

systemSyslogTable 0.1.3309.1.3.35.19
List of last 1000 syslog entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SystemSyslogTableEntry

systemSyslogTableEntry 0.1.3309.1.3.35.19.1
Syslog history table entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  SystemSyslogTableEntry  

systemSyslogIndex 0.1.3309.1.3.35.19.1.1
Syslog history table index.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

systemSyslogTimestamp 0.1.3309.1.3.35.19.1.2
Time when syslog occurred.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(24)  

systemSyslogVersion 0.1.3309.1.3.35.19.1.3
Version of the sending machine.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..14)  

systemSyslogAddress 0.1.3309.1.3.35.19.1.4
IP Address of the machine which send the syslog.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

systemSyslogMessage 0.1.3309.1.3.35.19.1.5
Type of syslog.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..429)  

systemStaticPortMappingTable 0.1.3309.1.3.35.20
List of Static Port-mapping Table entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SystemStaticPortMappingTableEntry

systemStaticPortMappingTableEntry 0.1.3309.1.3.35.20.1
Static Port Mapping table entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  SystemStaticPortMappingTableEntry  

systemStaticPortMappingIndex 0.1.3309.1.3.35.20.1.1
Access/reboot history table index.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

systemStaticPortMappingMAC 0.1.3309.1.3.35.20.1.2
Physical Address of the subscriber/device entered in one of the formats: 001122334455, 00-11-22-33-44-55 or 00:11:22:33:44:55. Default value is 00:00:00:00:00:00 .
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..17)  

systemStaticPortMappingInternalIP 0.1.3309.1.3.35.20.1.3
IP Address of the subscriber/device.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

systemStaticPortMappingInternalPort 0.1.3309.1.3.35.20.1.4
Internal Port (of the subscriber/device)
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..65535  

systemStaticPortMappingExternalIP 0.1.3309.1.3.35.20.1.5
IP Address of the NSE subscriber side (DAT IP).
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

systemStaticPortMappingExternalPort 0.1.3309.1.3.35.20.1.6
External Port (of the NSE)
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1024..65535  

systemStaticPortMappingRemoteIP 0.1.3309.1.3.35.20.1.7
(OPTIONAL) IP Address of the network side machine.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

systemStaticPortMappingRemotePort 0.1.3309.1.3.35.20.1.8
(OPTIONAL) Remote Port (of the network side machine)
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

systemStaticPortMappingProto 0.1.3309.1.3.35.20.1.9
Transport Protocol (TCP, UDP)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER udp(0), tcp(1)  

systemStaticPortMappingStatus 0.1.3309.1.3.35.20.1.10
Status of the Static Port-mapping table entry.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

blockIcmpFromPending 0.1.3309.1.3.35.21
Set to 1 to enable blocking ICMP packets from pending subscribers.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

timeCurrentDateAndTime 0.1.3309.1.3.36.1
Current date and time.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(24)  

timeOffsetSign 0.1.3309.1.3.36.2
Offset sign for time offset (+/- hh:mm) from UTC. Note: you must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER plus(0), minus(1)  

timeOffsetHours 0.1.3309.1.3.36.3
Hours offset for time offset (+/- hh:mm) from UTC. Note: you must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..23  

timeOffsetMinutes 0.1.3309.1.3.36.4
Minutes offset for time offset (+/- hh:mm) from UTC. Note: you must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..59  

timeServerTimeout 0.1.3309.1.3.36.5
Time server timeout in seconds. Note: you must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..200  

timeServer1 0.1.3309.1.3.36.6
IP address or DNS name of the first time server. Note: you must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..238)  

timeServer2 0.1.3309.1.3.36.7
IP address or DNS name of the second time server. Note: you must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..238)  

timeServer3 0.1.3309.1.3.36.8
IP address or DNS name of the third time server. Note: you must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..238)  

timeServer4 0.1.3309.1.3.36.9
IP address or DNS name of the fourth time server. Note: you must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..238)  

urlFilteringOn 0.1.3309.1.3.37.1
Setting this value to (1) will enable URL Filtering feature. Setting this value to (0) will disable it.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

urlFilteringIPTable 0.1.3309.1.3.37.2
Table of IP addresses that will be filtered.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UrlFilteringIPTableEntry

urlFilteringIPTableEntry 0.1.3309.1.3.37.2.1
URL Filtering IP table entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  UrlFilteringIPTableEntry  

urlFilteringIPTableIndex 0.1.3309.1.3.37.2.1.1
URL Filtering IP Table Index
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

urlFilteringIPTableAddress 0.1.3309.1.3.37.2.1.2
IP address traffic to which will be blocked.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

urlFilteringIPTableStatus 0.1.3309.1.3.37.2.1.3
Status of the urlFilteringIPTable entry.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

urlFilteringDNSTable 0.1.3309.1.3.37.3
Table of DNS names or Domain names that will be filtered.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UrlFilteringDNSTableEntry

urlFilteringDNSTableEntry 0.1.3309.1.3.37.3.1
URL Filtering DNS table entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  UrlFilteringDNSTableEntry  

urlFilteringDNSTableIndex 0.1.3309.1.3.37.3.1.1
URL Filtering DNS Table Index
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

urlFilteringDNSTableName 0.1.3309.1.3.37.3.1.2
DNS name or Domain name traffic to which will be blocked.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..237)  

urlFilteringDNSTableStatus 0.1.3309.1.3.37.3.1.3
Status of the URL Filtering DNS table entry.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

macFilteringOn 0.1.3309.1.3.41.1
Setting this value to (1) will enable the MAC Filtering feature. Setting this value to (0) will disable it.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

macFilteringTable 0.1.3309.1.3.41.4
Table of MAC addresses that will be filtered.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MacFilteringTableEntry

macFilteringTableEntry 0.1.3309.1.3.41.4.1
MAC Filtering IP table entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacFilteringTableEntry  

macFilteringTableIndex 0.1.3309.1.3.41.4.1.1
MAC Filtering Table Index
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

macFilteringTableAddress 0.1.3309.1.3.41.4.1.2
MAC address traffic to be filtered.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

macFilteringStatus 0.1.3309.1.3.41.4.1.3
Status of the MAC Filter Table Entry.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

tunnelingOn 0.1.3309.1.3.42.1
Setting this value to (1) will enable tunneling. Setting this value to (0) will disable it.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

wirelessSsid 0.1.3309.1.3.43.1
Default SSID of the AG. Note: you must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

wirelessSsidBroadcastOn 0.1.3309.1.3.43.2
Setting this value to (1) will enable Default SSID Broadcast. Setting this value to (0) will disable it. Note: you must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

wirelessChannel 0.1.3309.1.3.43.3
Channel number for the wireless interface. Setting it to zero will enable auto channel configuration. Note: not all of the channels might be available depending on the regulatory domain and type of wireless interface (b/g or a). Note: you must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..14 | 36 | 40 | 44 | 48 | 52 | 56 | 60 | 64  

wirelessRate 0.1.3309.1.3.43.4
Data rate for the wireless interface. Note: not all of the rates might be available depending on type of wireless interface (b/g or a). Note: you must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER auto(0), rate-1Mbits(1), rate-2Mbits(2), rate-5andhalfMbits(3), rate-6Mbits(4), rate-9Mbits(5), rate-11Mbits(6), rate-12Mbits(7), rate-18Mbits(8), rate-24Mbits(9), rate-36Mbits(10), rate-48Mbits(11), rate-54Mbits(12)  

wirelessPower 0.1.3309.1.3.43.5
Level of transmit power for the wireless interface. Note: you must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER full(0), half(1), quarter(2), eighth(3), min(4)  

wirelessFragLength 0.1.3309.1.3.43.6
Fragment length. Note: you must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 256..2346  

wirelessRtsLength 0.1.3309.1.3.43.7
RTS length. Note: you must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 256..2346  

wirelessBeaconInterval 0.1.3309.1.3.43.8
Beacon interval. Note: you must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 20..1000  

wirelessDtim 0.1.3309.1.3.43.9
Delivery Traffic Indication Message (DTIM). Note: you must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..255  

wirelessShortPreambleOn 0.1.3309.1.3.43.10
Setting this value to (1) will enable short preamble. Setting this value to (0) will disable it. Note: you must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

wirelessMssid 0.1.3309.1.3.43.11
OBJECT IDENTIFIER    

wirelessMssidVlanOn 0.1.3309.1.3.43.11.1
Set to 1 to enable, 0 to disable SSID based WAN VLAN. Note: enabling SSID based WAN VLAN will automatically disable RADIUS based WAN VLAN.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

wirelessMssidVlanDefaultOn 0.1.3309.1.3.43.11.2
Set to 1 to enable default 802.1q tag for system traffic, 0 to disable.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

wirelessMssidVlanDefaultTag 0.1.3309.1.3.43.11.3
Set the default 802.1q tag for system traffic.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..4094  

wirelessMssidTable 0.1.3309.1.3.43.11.4
List of multiple SSID settings.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WirelessMssidTableEntry

wirelessMssidTableEntry 0.1.3309.1.3.43.11.4.1
SSID entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  WirelessMssidTableEntry  

mssidIndex 0.1.3309.1.3.43.11.4.1.1
SSID index.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

mssidName 0.1.3309.1.3.43.11.4.1.2
SSID name. Note: you must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

mssidVlan 0.1.3309.1.3.43.11.4.1.3
SSID VLAN. Note: you must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..4094  

mssidStatus 0.1.3309.1.3.43.11.4.1.4
Status of the Multiple SSID table entry.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

wirelessWep 0.1.3309.1.3.43.12
OBJECT IDENTIFIER    

wirelessWepOn 0.1.3309.1.3.43.12.1
Setting this value to (1) will enable WEP. Setting this value to (0) will disable it. Note: you must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

wirelessWepClients 0.1.3309.1.3.43.12.3
Type of clients supported by AG.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(6..21)  

wirelessWepAuthType 0.1.3309.1.3.43.12.4
Setting this value to (0) will set 802.11 authentication type to open. Setting this value to (1) will set it to shared. Note: you must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER open(0), shared(1)  

wirelessWepNon1xAllowedOn 0.1.3309.1.3.43.12.5
Setting this value to (1) will allow access for non-802.1x clients. Setting this value to (0) will disallow it. Note: you must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

wirelessWepKeyType 0.1.3309.1.3.43.12.6
Type of the WEP key: Hexadecimal digits or ASCII characters. Note: you must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER hex(0), ascii(1)  

wirelessWepDefaultKey 0.1.3309.1.3.43.12.7
Default WEP Key. Index of a WEP key which will be used to encrypt all transmitted and received frames for the stations which do not have a private key associated with them. Note: you must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER key-1(1), key-2(2), key-3(3), key-4(4)  

wirelessWepKey1 0.1.3309.1.3.43.12.8
WEP Key 1. Note: make sure that key length is correct depending on the key type: Ascii 64-bit key - 5 characters long Ascii 128-bit key - 13 characters long Ascii 152-bit key - 16 characters long Hex 64-bit key - 10 hex digits long Hex 128-bit key - 26 hex digits long Hex 152-bit key - 32 hex digits long Note: you must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

wirelessWepKey2 0.1.3309.1.3.43.12.9
WEP Key 2. Note: make sure that key length is correct depending on the key type: Ascii 64-bit key - 5 characters long Ascii 128-bit key - 13 characters long Ascii 152-bit key - 16 characters long Hex 64-bit key - 10 hex digits long Hex 128-bit key - 26 hex digits long Hex 152-bit key - 32 hex digits long Note: you must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

wirelessWepKey3 0.1.3309.1.3.43.12.10
WEP Key 3. Note: make sure that key length is correct depending on the key type: Ascii 64-bit key - 5 characters long Ascii 128-bit key - 13 characters long Ascii 152-bit key - 16 characters long Hex 64-bit key - 10 hex digits long Hex 128-bit key - 26 hex digits long Hex 152-bit key - 32 hex digits long Note: you must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

wirelessWepKey4 0.1.3309.1.3.43.12.11
WEP Key 4. Note: make sure that key length is correct depending on the key type: Ascii 64-bit key - 5 characters long Ascii 128-bit key - 13 characters long Ascii 152-bit key - 16 characters long Hex 64-bit key - 10 hex digits long Hex 128-bit key - 26 hex digits long Hex 152-bit key - 32 hex digits long Note: you must reboot for changes to take effect.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

failedLogin 0.1.3309.1.3.0.8
Failed Login attempt
Status: current Access: read-write
NOTIFICATION-TYPE    

subCapacityReached 0.1.3309.1.3.0.9
Subscriber Capacity Reached
Status: current Access: read-write
NOTIFICATION-TYPE    

nseReboot 0.1.3309.1.3.0.10
The unit has rebooted
Status: current Access: read-write
NOTIFICATION-TYPE    

nseRadCapacityReached 0.1.3309.1.3.0.15
This trap is generated when the limit of Radius caching file is reached.
Status: current Access: read-write
NOTIFICATION-TYPE    

pppoeSvcName 0.1.3309.1.3.44.1
Servicename that will be requested of the PPPoE client. Blank means any service is acceptable.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

pppEchoReqIntvl 0.1.3309.1.3.44.2
Frequency in seconds that LCP echo requests will be sent to the server.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

pppEchoMaxNonresp 0.1.3309.1.3.44.3
Maximum number of echo requests that can go unresponded to before the PPP link is considered to be down.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

pppAuthUsername 0.1.3309.1.3.44.4
Username to be used during authentication phase of establishing PPP link. Used for PAP or CHAP.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..128)  

pppAuthPassword 0.1.3309.1.3.44.5
Password/Secret to be used during authentication phase of establishing PPP link. Used for PAP or CHAP.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..128)  

pppIpCfgMode 0.1.3309.1.3.44.6
Decides whether to request an IP address from the server (dynamic) or inform the server of the desired IP address (static)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER dynamic(0), static(1)  

pppStaticIpAddr 0.1.3309.1.3.44.7
If pppIpCfgMode is set to static, this is the IP address that will be used.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

pppMaxTcpMss 0.1.3309.1.3.44.8
Specifies the maximum TCP MSS option value to use for subscriber TCP connections across the PPP network interface. The actual value used may be less than the configured value if necessary based on the MTU of the PPP interface. Values above 1952 are not allowed.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

localWebPages 0.1.3309.1.3.52.4
OBJECT IDENTIFIER    

localWebImages 0.1.3309.1.3.52.8
OBJECT IDENTIFIER    

localWebPagesTable 0.1.3309.1.3.52.4.1
Table of local Web page names.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LocalWebPagesTableEntry

localWebPagesTableEntry 0.1.3309.1.3.52.4.1.1
Local Web Pages table entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  LocalWebPagesTableEntry  

localWebPagesTableIndex 0.1.3309.1.3.52.4.1.1.1
Local Web Pages Table Index.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

localWebPagesTableName 0.1.3309.1.3.52.4.1.1.2
Local Web Pages entries.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..237)  

localWebPagesTableStatus 0.1.3309.1.3.52.4.1.1.3
Status of the Local Web pages table entry.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

localWebImagesTable 0.1.3309.1.3.52.8.1
Table of local Web image names.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LocalWebImagesTableEntry

localWebImagesTableEntry 0.1.3309.1.3.52.8.1.1
Local Web Images table entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  LocalWebImagesTableEntry  

localWebImagesTableIndex 0.1.3309.1.3.52.8.1.1.1
Local Web Images Index
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

localWebImagesTableName 0.1.3309.1.3.52.8.1.1.2
Local Web Image entries.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..237)  

localWebImagesTableStatus 0.1.3309.1.3.52.8.1.1.3
Status of local Web images table entry.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

ipsecVpnOn 0.1.3309.1.3.54.1
Setting this value to (1) enables IPSec over the network interface. Setting it to zero disables it. Valid license is required. When this variable is changed, system must be rebooted for the change to take effect. (NOTE: This is not to be confused with the MIB variable ipsecOn, which pertains to the passthru of IPSec traffic to/from a subscriber host.)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

ipsecPeers 0.1.3309.1.3.54.4
OBJECT IDENTIFIER    

ipsecPolicies 0.1.3309.1.3.54.5
OBJECT IDENTIFIER    

ipsecSaStatus 0.1.3309.1.3.54.6
OBJECT IDENTIFIER    

ipsecPeerTable 0.1.3309.1.3.54.4.1
List of IPSec peers.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpsecPeerTableEntry

ipsecPeerTableEntry 0.1.3309.1.3.54.4.1.1
Parameters for a specific IPSec peer.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpsecPeerTableEntry  

ipsecPeerIndex 0.1.3309.1.3.54.4.1.1.1
IPSec Peer Index
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

ipsecPeerIpAddr 0.1.3309.1.3.54.4.1.1.2
IP Address of the IPSec peer.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

ipsecPeerAuthMethod 0.1.3309.1.3.54.4.1.1.3
Method to be used to authenticate and be authenticated by IPSec peer
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER preSharedKey(0), x509Certificate(1)  

ipsecPeerSharedKey 0.1.3309.1.3.54.4.1.1.4
The key to be used if ipsecPeerAuthMethod is preSharedKey.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..128)  

ipsecPeerPrivkeyFile 0.1.3309.1.3.54.4.1.1.5
The filename (within the /flash/ipseccrt directory) of the file containing the private key to be used for X509 authentication. Only needed if ipsecPeerAuthMethod is x509Certificate
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..20)  

ipsecPeerCertFile 0.1.3309.1.3.54.4.1.1.6
The filename (within the /flash/ipseccrt directory) of the file containing the X.509 certificate to be used for X509 authentication. Only needed if ipsecPeerAuthMethod is x509Certificate
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..20)  

ipsecPeerEncDesOk 0.1.3309.1.3.54.4.1.1.7
Indicates whether DES encryption is allowed to be used on the IKE channel between the NSE and this peer.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notAllowed(0), allowed(1)  

ipsecPeerEnc3DesOk 0.1.3309.1.3.54.4.1.1.8
Indicates whether 3DES encryption is allowed to be used on the IKE channel between the NSE and this peer.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notAllowed(0), allowed(1)  

ipsecPeerHashMd5Ok 0.1.3309.1.3.54.4.1.1.9
Indicates whether MD5 hashing is allowed to be used on the IKE channel between the NSE and this peer.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notAllowed(0), allowed(1)  

ipsecPeerHashShaOk 0.1.3309.1.3.54.4.1.1.10
Indicates whether SHA hashing is allowed to be used on the IKE channel between the NSE and this peer.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notAllowed(0), allowed(1)  

ipsecPeerKeyStrength 0.1.3309.1.3.54.4.1.1.11
The key strength to be used on the IKE channel between the NSE and this peer
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER key768-bit(0), key1024-bit(1)  

ipsecPeerLifetime 0.1.3309.1.3.54.4.1.1.12
The lifetime (in seconds) of the IKE channel between the NSE and this peer, before it needs to be torn down and re-established.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

ipsecPeerStatus 0.1.3309.1.3.54.4.1.1.20
Status of the IPSec peer table entry.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

ipsecPolicyTable 0.1.3309.1.3.54.5.1
List of IPSec security policies.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpsecPolicyTableEntry

ipsecPolicyTableEntry 0.1.3309.1.3.54.5.1.1
Parameters for a specific IPSec security policy.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpsecPolicyTableEntry  

ipsecPolicyIndex 0.1.3309.1.3.54.5.1.1.1
IPSec Policy Index
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

ipsecPolicyPeerIp 0.1.3309.1.3.54.5.1.1.2
IP Address of the IPSec peer for this policy. There must be an entry in the peer table for this peer
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

ipsecPolicyProtocol 0.1.3309.1.3.54.5.1.1.3
The IP protocol number (e.g. 6 for TCP) of the protocol this policy pertains to. a zero means it pertains to ANY protocol.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

ipsecPolicyRemIp 0.1.3309.1.3.54.5.1.1.4
IP Address of the remote host/subnet to which this policy pertains.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

ipsecPolicyRemSubnet 0.1.3309.1.3.54.5.1.1.5
Subnet mask of the remote subnet to which this policy pertains.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

ipsecPolicyRemPort 0.1.3309.1.3.54.5.1.1.6
The remote TCP/UDP port number to which this policy pertains. A zero means it pertains to ANY port number. This field is only used if the protocol number is 6 (TCP) or 17 (UDP).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

ipsecPolicyUseNetIp 0.1.3309.1.3.54.5.1.1.7
Indicates whether or not this policy pertains to traffic originated by and/or destined to the NSE's network interface IP address. Otherwise it would pertain to a device on the subscriber network.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

ipsecPolicyLocIp 0.1.3309.1.3.54.5.1.1.8
If ipsecPolicyUseNetIp is no, this is the IP Address of the subscriber-side host/subnet to which this policy pertains.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

ipsecPolicyLocSubnet 0.1.3309.1.3.54.5.1.1.9
If ipsecPolicyUseNetIp is no, this is the Subnet mask of the subscriber-side subnet to which this policy pertains.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

ipsecPolicyLocPort 0.1.3309.1.3.54.5.1.1.10
The local TCP/UDP port number to which this policy pertains. A zero means it pertains to ANY port number. This field is only used if the protocol number is 6 (TCP) or 17 (UDP).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

ipsecPolicyType 0.1.3309.1.3.54.5.1.1.11
The type of IPSec security policy this is, i.e., what type of action to take on packets that fit the traffic selectors.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER discard(0), bypass(1), esp(2), ah(3)  

ipsecPolicyDirType 0.1.3309.1.3.54.5.1.1.12
The traffic direction to which this policy pertains. Used only for discard or bypass policies (ESP and AH tunnels always pertain to both directions)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER inOnly(0), outOnly(1), inAndOut(2)  

ipsecPolicyEncDesOk 0.1.3309.1.3.54.5.1.1.13
Indicates whether DES encryption is allowed to be used on the security association based on this policy. Pertains only to ESP tunnels.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notAllowed(0), allowed(1)  

ipsecPolicyEnc3desOk 0.1.3309.1.3.54.5.1.1.14
Indicates whether 3DES encryption is allowed to be used on the security association based on this policy. Pertains only to ESP tunnels.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notAllowed(0), allowed(1)  

ipsecPolicyEncNullOk 0.1.3309.1.3.54.5.1.1.15
Indicates whether NULL encryption (i.e., not encrypted) is allowed to be used on the security association based on this policy. Pertains only to ESP tunnels.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notAllowed(0), allowed(1)  

ipsecPolicyAuthMd5Ok 0.1.3309.1.3.54.5.1.1.16
Indicates whether MD5 authentication is allowed to be used on the security association based on this policy. Pertains to both ESP and AH tunnels.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notAllowed(0), allowed(1)  

ipsecPolicyAuthShaOk 0.1.3309.1.3.54.5.1.1.17
Indicates whether SHA authentication is allowed to be used on the security association based on this policy. Pertains to both ESP and AH tunnels.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notAllowed(0), allowed(1)  

ipsecPolicyAuthNullOk 0.1.3309.1.3.54.5.1.1.18
Indicates whether no authentication is allowed to be used on the security association based on this policy. Pertains only to ESP tunnels.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notAllowed(0), allowed(1)  

ipsecPolicyPfsStrength 0.1.3309.1.3.54.5.1.1.19
Indicates whether perfect forward secrecy is to be used on the security association based on this policy, and if so what lever of keying strength to use. Pertains to either ESP or AH tunnels.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER pfsNone(0), pfs768(1), pfs1024(2)  

ipsecPolicyMaxLifetime 0.1.3309.1.3.54.5.1.1.20
The maximum lifetime (in seconds) a security association based on this policy may stay up before it must either be torn down or renewed. A zero means there is no maximum.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

ipsecPolicyMaxLifesize 0.1.3309.1.3.54.5.1.1.21
The maximum amount of data (in bytes) that may pass thru a tunnel based on this policy before it must either be torn down or renewed. A zero means there is no maximum.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

ipsecPolicyAutoRenew 0.1.3309.1.3.54.5.1.1.22
Indicates whether the security association based on this policy should be automatically renewed or not. Used only if either ipsecPolicyMaxLifesize or ipsecPolicyMaxLifetime is non-zero.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

ipsecPolicyStatus 0.1.3309.1.3.54.5.1.1.40
Status of the IPSec policy table entry.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

ipsecSaStatusTable 0.1.3309.1.3.54.6.1
List of the status of security associations corresponding to configured IPSec security policies.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpsecSaStatusTableEntry

ipsecSaStatusTableEntry 0.1.3309.1.3.54.6.1.1
Information about the status of an IPSec security association.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpsecSaStatusTableEntry  

ipsecSaStatusIndex 0.1.3309.1.3.54.6.1.1.1
IPSec Security Association Status Index
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

ipsecSaStatusState 0.1.3309.1.3.54.6.1.1.2
Indicates the state ofwhether the security association corresponding to the configured security policy is presently up or down.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ipsecUp(0), ipsecDisabled(1), notConfiguredInStack(2), noIkeChannelToPeer(3), notNegotiatedWithPeer(4)  

ipsecSaStatusStatus 0.1.3309.1.3.54.6.1.1.20
Status of the IPSec security association table entry.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor