MPLS-LDP-FRAME-RELAY-STD-MIB

File: MPLS-LDP-FRAME-RELAY-STD-MIB.mib (22772 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMPv2-TC
FRAME-RELAY-DTE-MIB IF-MIB MPLS-TC-STD-MIB
MPLS-LDP-STD-MIB

Imported symbols

OBJECT-TYPE MODULE-IDENTITY Unsigned32
MODULE-COMPLIANCE OBJECT-GROUP RowStatus
StorageType DLCI InterfaceIndexOrZero
mplsStdMIB mplsLdpEntityLdpId mplsLdpEntityIndex
mplsLdpPeerLdpId

Defined Types

MplsLdpEntityFrameRelayEntry  
SEQUENCE    
  mplsLdpEntityFrameRelayIfIndexOrZero InterfaceIndexOrZero
  mplsLdpEntityFrameRelayMergeCap INTEGER
  mplsLdpEntityFrameRelayLRComponents Unsigned32
  mplsLdpEntityFrameRelayVcDirectionality INTEGER
  mplsLdpEntityFrameRelayStorageType StorageType
  mplsLdpEntityFrameRelayRowStatus RowStatus

MplsLdpEntityFrameRelayLREntry  
SEQUENCE    
  mplsLdpEntityFrameRelayLRMinDlci DLCI
  mplsLdpEntityFrameRelayLRMaxDlci DLCI
  mplsLdpEntityFrameRelayLRLen INTEGER
  mplsLdpEntityFrameRelayLRStorageType StorageType
  mplsLdpEntityFrameRelayLRRowStatus RowStatus

MplsLdpFrameRelaySessionEntry  
SEQUENCE    
  mplsLdpFrameRelaySessionMinDlci DLCI
  mplsLdpFrameRelaySessionMaxDlci DLCI
  mplsLdpFrameRelaySessionLen INTEGER

Defined Values

mplsLdpFrameRelayStdMIB 1.3.6.1.2.1.10.166.6
Copyright (C) The Internet Society (year). The initial version of this MIB module was published in RFC 3815. For full legal notices see the RFC itself or see: http://www.ietf.org/copyrights/ianamib.html This MIB contains managed object definitions for configuring and monitoring the Multiprotocol Label Switching (MPLS), Label Distribution Protocol (LDP), utilizing Frame Relay as the Layer 2 media.
MODULE-IDENTITY    

mplsLdpFrameRelayObjects 1.3.6.1.2.1.10.166.6.1
OBJECT IDENTIFIER    

mplsLdpFrameRelayConformance 1.3.6.1.2.1.10.166.6.2
OBJECT IDENTIFIER    

mplsLdpEntityFrameRelayObjects 1.3.6.1.2.1.10.166.6.1.1
OBJECT IDENTIFIER    

mplsLdpEntityFrameRelayTable 1.3.6.1.2.1.10.166.6.1.1.1
This table contains Frame Relay specific information which could be used in the 'Optional Parameters' and other Frame Relay specific information. This table 'sparse augments' the mplsLdpEntityTable when Frame Relay is the Layer 2 medium.
OBJECT-TYPE    
  SEQUENCE OF  
    MplsLdpEntityFrameRelayEntry

mplsLdpEntityFrameRelayEntry 1.3.6.1.2.1.10.166.6.1.1.1.1
An entry in this table represents the Frame Relay optional parameters associated with the LDP entity.
OBJECT-TYPE    
  MplsLdpEntityFrameRelayEntry  

mplsLdpEntityFrameRelayIfIndexOrZero 1.3.6.1.2.1.10.166.6.1.1.1.1.1
This value represents either the InterfaceIndex of the 'ifLayer' where the Frame Relay Labels 'owned' by this entry were created, or 0 (zero). The value of zero means that the InterfaceIndex is not known. For example, if the InterfaceIndex is created subsequent to the Frame Relay Label's creation, then it would not be known. However, if the InterfaceIndex is known, then it must be represented by this value. If an InterfaceIndex becomes known, then the network management entity (e.g., SNMP agent) responsible for this object MUST change the value from 0 (zero) to the value of the InterfaceIndex. If an Frame Relay Label is being used in forwarding data, then the value of this object MUST be the InterfaceIndex.
OBJECT-TYPE    
  InterfaceIndexOrZero  

mplsLdpEntityFrameRelayMergeCap 1.3.6.1.2.1.10.166.6.1.1.1.1.2
This represents whether or not the Frame Relay merge capability is supported. This is the EXACT value for the Frame Relay Session Parameter, field M (for Frame Relay Merge Capabilities). The Frame Relay Session Parameter is an optional parameter in the Initialization Message. The description from rfc3036.txt is: 'M, Frame Relay Merge Capabilities Specifies the merge capabilities of a Frame Relay switch. The following values are supported in this version of the specification: Value Meaning 0 Merge not supported 1 Merge supported Non-merge and merge Frame Relay LSRs may freely interoperate.' Please refer to the following reference for a complete description of this feature.
OBJECT-TYPE    
  INTEGER notSupported(0), supported(1)  

mplsLdpEntityFrameRelayLRComponents 1.3.6.1.2.1.10.166.6.1.1.1.1.3
Number of Label Range Components in the Initialization message. This also represents the number of entries in the mplsLdpEntityFrameRelayLRTable which correspond to this entry. This is the EXACT value for the Frame Relay Session Parameter, field N (for Number of label range components). The Frame Relay Session Parameter is an optional parameter in the Initialization Message. The description from rfc3036.txt is: 'N, Number of label range components Specifies the number of Frame Relay Label Range Components included in the TLV.' Please refer to the following reference for a complete description of this feature.
OBJECT-TYPE    
  Unsigned32 1..65535  

mplsLdpEntityFrameRelayVcDirectionality 1.3.6.1.2.1.10.166.6.1.1.1.1.4
If the value of this object is 'bidirectional(0)', then the LSR supports the use of a given DLCI as a label for both directions independently. If the value of this object is 'unidirectional(1)', then the LSR uses the given DLCI as a label in only one direction. This is the EXACT value for the Frame Relay Session Parameter, field D (for VC Directionality). The Frame Relay Session Parameter is an optional parameter in the Initialization Message. The description from rfc3036.txt is: 'D, VC Directionality A value of 0 specifies bidirectional VC capability, meaning the LSR can support the use of a given DLCI as a label for both link directions independently. A value of 1 specifies unidirectional VC capability, meaning a given DLCI may appear in a label mapping for one direction on the link only. When either or both of the peers specifies unidirectional VC capability, both LSRs use unidirectional VC label assignment for the link as follows. The LSRs compare their LDP Identifiers as unsigned integers. The LSR with the larger LDP Identifier may assign only odd-numbered DLCIs in the range as labels. The system with the smaller LDP Identifier may assign only even-numbered DLCIs in the range as labels.' Please refer to the following reference for a complete description of this feature.
OBJECT-TYPE    
  INTEGER bidirectional(0), unidirection(1)  

mplsLdpEntityFrameRelayStorageType 1.3.6.1.2.1.10.166.6.1.1.1.1.5
The storage type for this conceptual row. Conceptual rows having the value 'permanent(4)' need not allow write-access to any columnar objects in the row.
OBJECT-TYPE    
  StorageType  

mplsLdpEntityFrameRelayRowStatus 1.3.6.1.2.1.10.166.6.1.1.1.1.6
The status of this conceptual row. All writable objects in this row may be modified at any time, however, as described in detail in the section entitled, 'Changing Values After Session Establishment', and again described in the DESCRIPTION clause of the mplsLdpEntityAdminStatus object, if a session has been initiated with a Peer, changing objects in this table will wreak havoc with the session and interrupt traffic. To repeat again: the recommended procedure is to set the mplsLdpEntityAdminStatus to down, thereby explicitly causing a session to be torn down. Then, change objects in this entry, then set the mplsLdpEntityAdminStatus to enable which enables a new session to be initiated.
OBJECT-TYPE    
  RowStatus  

mplsLdpEntityFrameRelayLRTable 1.3.6.1.2.1.10.166.6.1.1.2
This table contains information about the Optional Parameters for the Frame Relay Session in the LDP Initialization Message, specifically it contains information about the Frame Relay Label Range Components. If the value of the object 'mplsLdpEntityOptionalParameters' contains the value of 'frameRelaySessionParameters(3)' then there must be at least one corresponding entry in this table.
OBJECT-TYPE    
  SEQUENCE OF  
    MplsLdpEntityFrameRelayLREntry

mplsLdpEntityFrameRelayLREntry 1.3.6.1.2.1.10.166.6.1.1.2.1
An entry in this table represents the Frame Relay Label Range Component associated with the LDP entity.
OBJECT-TYPE    
  MplsLdpEntityFrameRelayLREntry  

mplsLdpEntityFrameRelayLRMinDlci 1.3.6.1.2.1.10.166.6.1.1.2.1.1
The lower bound which is supported. This value should be the same as that in the Frame Relay Label Range Component's Minimum DLCI field. The value of zero is valid for the minimum DLCI field of the label.
OBJECT-TYPE    
  DLCI  

mplsLdpEntityFrameRelayLRMaxDlci 1.3.6.1.2.1.10.166.6.1.1.2.1.2
The upper bound which is supported. This value should be the same as that in the Frame Relay Label Range Component's Maximum DLCI field.
OBJECT-TYPE    
  DLCI  

mplsLdpEntityFrameRelayLRLen 1.3.6.1.2.1.10.166.6.1.1.2.1.3
This object specifies the length of the DLCI bits. This is the EXACT value for the Len field of the Frame Relay Label Range Component. The description from rfc3036.txt is: 'Len This field specifies the number of bits of the DLCI. The following values are supported: Len DLCI bits 0 10 2 23 Len values 1 and 3 are reserved.' Please refer to the following reference for a complete description of this feature.
OBJECT-TYPE    
  INTEGER tenDlciBits(0), twentyThreeDlciBits(2)  

mplsLdpEntityFrameRelayLRStorageType 1.3.6.1.2.1.10.166.6.1.1.2.1.4
The storage type for this conceptual row. Conceptual rows having the value 'permanent(4)' need not allow write-access to any columnar objects in the row.
OBJECT-TYPE    
  StorageType  

mplsLdpEntityFrameRelayLRRowStatus 1.3.6.1.2.1.10.166.6.1.1.2.1.5
The status of this conceptual row. All writable objects in this row may be modified at any time, however, as described in detail in the section entitled, 'Changing Values After Session Establishment', and again described in the DESCRIPTION clause of the mplsLdpEntityAdminStatus object, if a session has been initiated with a Peer, changing objects in this table will wreak havoc with the session and interrupt traffic. To repeat again: the recommended procedure is to set the mplsLdpEntityAdminStatus to down, thereby explicitly causing a session to be torn down. Then, change objects in this entry, then set the mplsLdpEntityAdminStatus to enable which enables a new session to be initiated.
OBJECT-TYPE    
  RowStatus  

mplsLdpFrameRelaySessionObjects 1.3.6.1.2.1.10.166.6.1.2
OBJECT IDENTIFIER    

mplsLdpFrameRelaySessionTable 1.3.6.1.2.1.10.166.6.1.2.1
A table of Frame Relay label range intersections between the LDP Entities and LDP Peers. Each row represents a single label range intersection. NOTE: this table cannot use the 'AUGMENTS' clause because there is not necessarily a one-to-one mapping between this table and the mplsLdpSessionTable.
OBJECT-TYPE    
  SEQUENCE OF  
    MplsLdpFrameRelaySessionEntry

mplsLdpFrameRelaySessionEntry 1.3.6.1.2.1.10.166.6.1.2.1.1
An entry in this table represents information on a single label range intersection between an LDP Entity and LDP Peer. The information contained in a row is read-only.
OBJECT-TYPE    
  MplsLdpFrameRelaySessionEntry  

mplsLdpFrameRelaySessionMinDlci 1.3.6.1.2.1.10.166.6.1.2.1.1.1
The lower bound of DLCIs which are supported. The value of zero is a valid value for the minimum DLCI field of the label.
OBJECT-TYPE    
  DLCI  

mplsLdpFrameRelaySessionMaxDlci 1.3.6.1.2.1.10.166.6.1.2.1.1.2
The upper bound of DLCIs which are supported.
OBJECT-TYPE    
  DLCI  

mplsLdpFrameRelaySessionLen 1.3.6.1.2.1.10.166.6.1.2.1.1.3
This object specifies the DLCI bits.
OBJECT-TYPE    
  INTEGER tenDlciBits(0), twentyThreeDlciBits(2)  

mplsLdpFrameRelayGroups 1.3.6.1.2.1.10.166.6.2.1
OBJECT IDENTIFIER    

mplsLdpFrameRelayCompliances 1.3.6.1.2.1.10.166.6.2.2
OBJECT IDENTIFIER    

mplsLdpFrameRelayModuleFullCompliance 1.3.6.1.2.1.10.166.6.2.2.1
Support for createAndWait and notInService is not required.
MODULE-COMPLIANCE    
  mplsLdpEntityFrameRelayRowStatus RowStatus active(1)
  active RowStatus createAndGo(4), destroy(6)
  mplsLdpEntityFrameRelayLRRowStatus RowStatus active(1)
  active RowStatus createAndGo(4), destroy(6)

mplsLdpFrameRelayModuleReadOnlyCompliance 1.3.6.1.2.1.10.166.6.2.2.2
Write access is not required, and active is the only status that needs to be supported.
MODULE-COMPLIANCE    
  mplsLdpEntityFrameRelayRowStatus RowStatus active(1)
  mplsLdpEntityFrameRelayLRRowStatus RowStatus active(1)

mplsLdpFrameRelayGroup 1.3.6.1.2.1.10.166.6.2.1.1
Objects that apply to all MPLS LDP implementations using Frame Relay as the Layer 2.
OBJECT-GROUP