MOXA-W2x50A-MIB

File: MOXA-W2x50A-MIB.mib (134277 bytes)

Imported modules

Imported symbols

enterprises	IpAddress	OBJECT-TYPE
MODULE-IDENTITY	DateAndTime	TEXTUAL-CONVENTION
MacAddress	DisplayString

Defined Types

PortList
Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.
TEXTUAL-CONVENTION
	OCTET STRING

InfraGeneralSettingEntry
SEQUENCE
	profileIndex	INTEGER
	profileName	DisplayString
	profileRFType	INTEGER
	profileWlanSSID	DisplayString

SecuritySettingEntry
SEQUENCE
	authentication	INTEGER
	encryption	INTEGER
	wepKeyLength	INTEGER
	wepKeyIndex	INTEGER
	wepKeyPassphrase	DisplayString
	wepKeyFormat	INTEGER
	eapMethod	INTEGER
	tunneledAuth	INTEGER
	wpaUsername	DisplayString
	wpaAnonymousUsername	DisplayString
	verifyServerCert	INTEGER
	trustedServerCert	INTEGER
	userCert	INTEGER
	userPrivateKey	INTEGER

OpModePortEntry
SEQUENCE
	portIndex	INTEGER
	portMode	INTEGER

RealCOMEntry
SEQUENCE
	realCOMTcpAliveCheck	INTEGER
	realCOMMaxConnection	INTEGER
	realCOMIgnoreJammedIp	INTEGER
	realCOMAllowDriverControl	INTEGER
	realCOMConnectionDownRTS	INTEGER
	realCOMConnectionDownDTR	INTEGER

Rfc2217Entry
SEQUENCE
	rfc2217TcpAliveCheck	INTEGER
	rfc2217TcpPort	INTEGER

TcpServerEntry
SEQUENCE
	tcpServerTcpAliveCheck	INTEGER
	tcpServerInactivityTime	INTEGER
	tcpServerMaxConnection	INTEGER
	tcpServerIgnoreJammedIp	INTEGER
	tcpServerAllowDriverControl	INTEGER
	tcpServerTcpPort	INTEGER
	tcpServerCmdPort	INTEGER
	tcpServerConnectionDownRTS	INTEGER
	tcpServerConnectionDownDTR	INTEGER

TcpClientEntry
SEQUENCE
	tcpClientTcpAliveCheck	INTEGER
	tcpClientInactivityTime	INTEGER
	tcpClientIgnoreJammedIp	INTEGER
	tcpClientDestinationAddress1	DisplayString
	tcpClientDestinationPort1	INTEGER
	tcpClientDestinationAddress2	DisplayString
	tcpClientDestinationPort2	INTEGER
	tcpClientDestinationAddress3	DisplayString
	tcpClientDestinationPort3	INTEGER
	tcpClientDestinationAddress4	DisplayString
	tcpClientDestinationPort4	INTEGER
	tcpClientDesignatedLocalPort1	INTEGER
	tcpClientDesignatedLocalPort2	INTEGER
	tcpClientDesignatedLocalPort3	INTEGER
	tcpClientDesignatedLocalPort4	INTEGER
	tcpClientConnectionControl	INTEGER

UdpEntry
SEQUENCE
	udpDestinationAddress1Begin	IpAddress
	udpDestinationAddress1End	IpAddress
	udpDestinationPort1	INTEGER
	udpDestinationAddress2Begin	IpAddress
	udpDestinationAddress2End	IpAddress
	udpDestinationPort2	INTEGER
	udpDestinationAddress3Begin	IpAddress
	udpDestinationAddress3End	IpAddress
	udpDestinationPort3	INTEGER
	udpDestinationAddress4Begin	IpAddress
	udpDestinationAddress4End	IpAddress
	udpDestinationPort4	INTEGER
	udpLocalListenPort	INTEGER

PairConnectionMasterEntry
SEQUENCE
	pairConnectionMasterTcpAliveCheck	INTEGER
	pairConnectionMasterDestnationAddress	DisplayString
	pairConnectionMasterDestnationTcpPort	INTEGER

PairConnectionSlaveEntry
SEQUENCE
	pairConnectionSlaveTcpAliveCheck	INTEGER
	pairConnectionSlaveLocalTcpPort	INTEGER

EthernetModemEntry
SEQUENCE
	ethernetModemTcpAliveCheck	INTEGER
	ethernetModemLocalTcpPort	INTEGER

ReverseTerminalEntry
SEQUENCE
	reverseTerminalTcpAliveCheck	INTEGER
	reverseTerminalInactivityTime	INTEGER
	reverseTerminalTcpPort	INTEGER
	reverseTerminalAuthenticationType	INTEGER
	reverseTerminalMapKeys	INTEGER

DataPackingPortEntry
SEQUENCE
	portPacketLength	INTEGER
	portDelimiter1Enable	INTEGER
	portDelimiter1	DisplayString
	portDelimiter2Enable	INTEGER
	portDelimiter2	DisplayString
	portDelimiterProcess	INTEGER
	portForceTransmit	INTEGER

ComParamPortEntry
SEQUENCE
	portAlias	DisplayString
	portInterface	INTEGER
	portBaudRate	INTEGER
	portDataBits	INTEGER
	portStopBits	INTEGER
	portParity	INTEGER
	portFlowControl	INTEGER
	portFIFO	INTEGER

DataBufferingPortEntry
SEQUENCE
	portBufferingEnable	INTEGER
	portSerialDataLoggingEnable	INTEGER

AccessibleIpListEntry
SEQUENCE
	accessibleIpListIndex	INTEGER
	activeAccessibleIpList	INTEGER
	accessibleIpListAddress	IpAddress
	accessibleIpListNetmask	IpAddress

PortEventSettingsEntry
SEQUENCE
	mailDCDchange	INTEGER
	trapDCDchange	INTEGER
	mailDSRchange	INTEGER
	trapDSRchange	INTEGER

MonitorRemoteIpEntry
SEQUENCE
	remoteIpIndex	INTEGER
	monitorRemoteIp	IpAddress

MonitorSerialPortStatusEntry
SEQUENCE
	monitorTxCount	INTEGER
	monitorRxCount	INTEGER
	monitorTxTotalCount	INTEGER
	monitorRxTotalCount	INTEGER
	monitorDSR	INTEGER
	monitorDTR	INTEGER
	monitorRTS	INTEGER
	monitorCTS	INTEGER
	monitorDCD	INTEGER

MonitorSerialPortErrorCountEntry
SEQUENCE
	monitorErrorCountFrame	INTEGER
	monitorErrorCountParity	INTEGER
	monitorErrorCountOverrun	INTEGER
	monitorErrorCountBreak	INTEGER

MonitorSerialPortSettingsEntry
SEQUENCE
	monitorBaudRate	INTEGER
	monitorDataBits	INTEGER
	monitorStopBits	DisplayString
	monitorParity	INTEGER
	monitorRTSCTSFlowControl	INTEGER
	monitorXONXOFFFlowControl	INTEGER
	monitorFIFO	INTEGER
	monitorInterface	INTEGER

MonitorSerialPortBufferingEntry
SEQUENCE
	monitorBuffering	INTEGER

Defined Values

moxa		1.3.6.1.4.1.8691
OBJECT IDENTIFIER

nport		1.3.6.1.4.1.8691.2
OBJECT IDENTIFIER

w2x50A		1.3.6.1.4.1.8691.2.13
The MIB module for Moxa NPort W2x50A series specific information.
MODULE-IDENTITY

swMgmt		1.3.6.1.4.1.8691.2.13.1
OBJECT IDENTIFIER

overview		1.3.6.1.4.1.8691.2.13.1.1
OBJECT IDENTIFIER

modelName		1.3.6.1.4.1.8691.2.13.1.1.1
The model name of the NPort. The possible values of this parameter are: 'NPort W2x50A' for NPort W2x50A.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

serialNumber		1.3.6.1.4.1.8691.2.13.1.1.2
The serial number of the NPort. Every NPort W2x50A series device server is assigned a unique serial number before it is shipped.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

firmwareVersion		1.3.6.1.4.1.8691.2.13.1.1.3
The version of the firmware currently running on the NPort.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

ethIPAddress		1.3.6.1.4.1.8691.2.13.1.1.4
The IP address of the NPort's Ethernet interface.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

ethMacAddress		1.3.6.1.4.1.8691.2.13.1.1.5
The MAC address of the NPort's Ethernet interface.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

wlanIPAddress		1.3.6.1.4.1.8691.2.13.1.1.6
The IP address of the NPort's WLAN interface.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

wlanMacAddress		1.3.6.1.4.1.8691.2.13.1.1.7
The MAC address of the NPort's WLAN interface.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

wlanSSID		1.3.6.1.4.1.8691.2.13.1.1.8
The SSID of WLAN.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

wlanNetworkType		1.3.6.1.4.1.8691.2.13.1.1.9
Network Type of Wireless LAN. The possible values are 'Infrastrcture Mode' and 'Ad-hoc Mode'
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

wlanSecurityMode		1.3.6.1.4.1.8691.2.13.1.1.10
Security mode of Wireless LAN. The possible values are 'Open System', 'Shared Key', 'WPA', 'WPA-PSK', 'WPA2', 'WPA2-PSK'
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

wlanRFType		1.3.6.1.4.1.8691.2.13.1.1.11
RF type of Wireless LAN. The possible values are 'Auto', '802.11b', '802.11g'
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

wlanCountryCode		1.3.6.1.4.1.8691.2.13.1.1.12
WLAN country code
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

wlanFastRoaming		1.3.6.1.4.1.8691.2.13.1.1.13
Fast roaming state
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

activeNetworkPort		1.3.6.1.4.1.8691.2.13.1.1.14
Current active network port. The possible values are 'WLAN', 'Ethernet'
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

upTime		1.3.6.1.4.1.8691.2.13.1.1.15
The time (in human-readable notation) since the system was last re-initialized.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

serialPort1		1.3.6.1.4.1.8691.2.13.1.1.16
View NPort's serial port 1 setting.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

serialPort2		1.3.6.1.4.1.8691.2.13.1.1.17
View NPort's serial port 2 setting.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

basicSetting		1.3.6.1.4.1.8691.2.13.1.2
OBJECT IDENTIFIER

serverSetting		1.3.6.1.4.1.8691.2.13.1.2.1
OBJECT IDENTIFIER

serverName		1.3.6.1.4.1.8691.2.13.1.2.1.1
A text string used to identify the NPort.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

serverLocation		1.3.6.1.4.1.8691.2.13.1.2.1.2
A text string used to identify the location of the NPort. This option is useful for specifying the location or application of different NPort device servers.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

timeSetting		1.3.6.1.4.1.8691.2.13.1.2.2
OBJECT IDENTIFIER

timeZone		1.3.6.1.4.1.8691.2.13.1.2.2.1
The time-zone index of the NPort.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	gmt-1200-Eniwetok-Kwajalein(0), gmt-1100-Midway-Island-Samoa(1), gmt-1000-Hawaii(2), gmt-0900-Alaska(3), gmt-0800-Pacific-Time-US-Canada-Tijuana(4), gmt-0700-Arizona(5), gmt-0700-Mountain-Time-US-Canada(6), gmt-0600-Central-Time-US-Canada(7), gmt-0600-Mexico-City-Tegucigalpa(8), gmt-0600-Saskatchewan(9), gmt-0500-Bogota-Lima-Quito(10), gmt-0500-Eastern-Time-US-Canada(11), gmt-0500-Indiana-East(12), gmt-0430-Caracas(13), gmt-0400-Atlantic-Time-Canada(14), gmt-0400-Georgetown-La-Paz(15), gmt-0400-Santiago(16), gmt-0330-Newfoundland(17), gmt-0300-Brasilia(18), gmt-0300-Buenos-Aires(19), gmt-0200-Mid-Atlantic(20), gmt-0100-Azores-Cape-Verde-Is(21), gmt-Casabanca-Monrovia(22), gmt-Greenich-Mean-Time-Dublin-Edinburgh-Lisbon-London(23), gmt-0100-Amsterdam-Berlin-Bern-Rome-Stockholm-Vienna(24), gmt-0100-Belgrade-Bratislava-Budapest-Ljubljana-Prague(25), gmt-0100-Brussels-Copenhagen-Madrid-Paris-Vilnius(26), gmt-0100-Sarajevo-Skopje-Warsaw-Zagreb(27), gmt-0200-Athens-Istanbul-Minsk(28), gmt-0200-Bucharest(29), gmt-0200-Cairo(30), gmt-0200-Harare-Pretoria(31), gmt-0200-Helsinki-Riga-Sofia-Tallinn(32), gmt-0200-Jerusalem(33), gmt-0300-Baghdad-Kuwait-Riyadh(34), gmt-0300-Moscow-St-Petersburg-Volgograd(35), gmt-0300-Mairobi(36), gmt-0330-Tehran(37), gmt-0400-Abu-Dhabi-Muscat(38), gmt-0400-Baku-Tbilisi(39), gmt-0430-Kabul(40), gmt-0500-Ekaterinburg(41), gmt-0500-Islamabad-Karachi-Tashkent(42), gmt-0530-Bombay-Calcutta-Madras-New-Delhi(43), gmt-0600-Astana-Almaty-Dhaka(44), gmt-0600-Colombo(45), gmt-0700-Bangkok-Hanoi-Jakarta(46), gmt-0800-Beijing-Chongqing-Hong-Kong-Urumqi(47), gmt-0800-Perth(48), gmt-0800-Singapore(49), gmt-0800-Taipei(50), gmt-0900-Osaka-Sapporo-Tokyo(51), gmt-0900-Seoul(52), gmt-0900-Yakutsk(53), gmt-0930-Adelaide(54), gmt-0930-Darwin(55), gmt-1000-Brisbane(56), gmt-1000-Canberra-Melbourne-Sydney(57), gmt-1000-Guam-Port-Moresby(58), gmt-1000-Hobart(59), gmt-1000-Vladivostok(60), gmt-1100-Magadan-Solomon-Is-New-Caledonia(61), gmt-1200-Auckland-Wllington(62), gmt-1200-Fiji-Kamchatka-Marshall-Is(63)

localTime		1.3.6.1.4.1.8691.2.13.1.2.2.2
The system time in the following format yyyy/mm/dd hh:mm:ss
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..19)

timeServer		1.3.6.1.4.1.8691.2.13.1.2.2.3
The NPort W2x50A series device server uses SNTP (RFC-1769) for auto time calibration. Input the correct 'Time server' IP address or domain name. Once the NPort W2x50A series device server is configured with the correct Time server address, it will request time information from the Time server every 10 minutes.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

networkSetting		1.3.6.1.4.1.8691.2.13.1.3
OBJECT IDENTIFIER

generalSetting		1.3.6.1.4.1.8691.2.13.1.3.1
OBJECT IDENTIFIER

dnsServer1IpAddr		1.3.6.1.4.1.8691.2.13.1.3.1.1
The first DNS server address. When the user wants to visit a particular website, the computer asks a Domain Name System (DNS) server for the website's correct IP address, and then the computer uses the response to connect to the web server. DNS is the way that Internet domain names are identified and translated into IP addresses. A domain name is an alphanumeric name, such as moxa.com, that it is usually easier to remember. A DNS server is a host that translates this kind of text-based domain name into the numeric IP address used to establish a TCP/IP connection.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

dnsServer2IpAddr		1.3.6.1.4.1.8691.2.13.1.3.1.2
The second DNS server address. When the user wants to visit a particular website, the computer asks a Domain Name System (DNS) server for the website's correct IP address, and then the computer uses the response to connect to the web server. DNS is the way that Internet domain names are identified and translated into IP addresses. A domain name is an alphanumeric name, such as moxa.com, that it is usually easier to remember. A DNS server is a host that translates this kind of text-based domain name into the numeric IP address used to establish a TCP/IP connection.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

ethernetSetting		1.3.6.1.4.1.8691.2.13.1.3.2
OBJECT IDENTIFIER

ethIpConfiguration		1.3.6.1.4.1.8691.2.13.1.3.2.1
The IP configuration mode of the NPort. You can choose from four possible IP configuration modes: Static, DHCP, DHCP/BOOTP, BOOTP.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	static(0), dhcp(1), bootp(2)

ethIpAddress		1.3.6.1.4.1.8691.2.13.1.3.2.2
An IP address is a number assigned to a network device (such as a computer) as a permanent address on the network. Computers use the IP address to identify and talk to each other over the network. Choose a proper IP address that is unique and valid in your network environment.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

ethNetMask		1.3.6.1.4.1.8691.2.13.1.3.2.3
A subnet mask represents all of the network hosts at one geographic location, in one building, or on the same local area network. When a packet is sent out over the network, the NPort W2x50A series device server will use the subnet mask to check whether the TCP/IP host specified in the packet is on the local network segment. If the address is on the same network segment as the NPort W2x50A series device server, a connection is established directly from the NPort W2x50A series device server. Otherwise, the connection is established through the given default gateway.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

ethDefaultGateway		1.3.6.1.4.1.8691.2.13.1.3.2.4
A gateway is a network computer that acts as an entrance to another network. Usually, the computers that control traffic within the network or at the local Internet service provider are gateway nodes. The NPort W2x50A series device server needs to know the IP address of the default gateway computer in order to communicate with the hosts outside the local network environment. For correct gateway IP address information, consult with the network administrator.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

ethBridgeMode		1.3.6.1.4.1.8691.2.13.1.3.2.5
Enable or disable the bridge function.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

wlanSetting		1.3.6.1.4.1.8691.2.13.1.3.3
OBJECT IDENTIFIER

wlanIpConfiguration		1.3.6.1.4.1.8691.2.13.1.3.3.1
The IP configuration mode of the NPort. You can choose from four possible IP configuration modes: Static, DHCP, DHCP/BOOTP, BOOTP.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	static(0), dhcp(1), bootp(2)

wlanIpAddress		1.3.6.1.4.1.8691.2.13.1.3.3.2
An IP address is a number assigned to a network device (such as a computer) as a permanent address on the network. Computers use the IP address to identify and talk to each other over the network. Choose a proper IP address that is unique and valid in your network environment.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

wlanNetMask		1.3.6.1.4.1.8691.2.13.1.3.3.3
A subnet mask represents all of the network hosts at one geographic location, in one building, or on the same local area network. When a packet is sent out over the network, the NPort W2x50A series device server will use the subnet mask to check whether the TCP/IP host specified in the packet is on the local network segment. If the address is on the same network segment as the NPort W2x50A series device server, a connection is established directly from the NPort W2x50A series device server. Otherwise, the connection is established through the given default gateway.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

wlanDefaultGateway		1.3.6.1.4.1.8691.2.13.1.3.3.4
A gateway is a network computer that acts as an entrance to another network. Usually, the computers that control traffic within the network or at the local Internet service provider are gateway nodes. The NPort W2x50A series device server needs to know the IP address of the default gateway computer in order to communicate with the hosts outside the local network environment. For correct gateway IP address information, consult with the network administrator.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

profileSetting		1.3.6.1.4.1.8691.2.13.1.3.4
OBJECT IDENTIFIER

networkType		1.3.6.1.4.1.8691.2.13.1.3.4.1
Select WLAN network type.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ad-hoc(0), infrastructure(1)

adhocProfile		1.3.6.1.4.1.8691.2.13.1.3.4.2
OBJECT IDENTIFIER

adhocGeneralSetting		1.3.6.1.4.1.8691.2.13.1.3.4.2.1
OBJECT IDENTIFIER

adhocProfileName		1.3.6.1.4.1.8691.2.13.1.3.4.2.1.1
Assign profile name.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..32)

adhocRFType		1.3.6.1.4.1.8691.2.13.1.3.4.2.1.2
Select WLAN network type.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	w802-11b-g(2)

adhocWlanSSID		1.3.6.1.4.1.8691.2.13.1.3.4.2.1.3
Set WLAN SSID
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..32)

adhocChannel		1.3.6.1.4.1.8691.2.13.1.3.4.2.1.4
Display currently used channel. When in Ad-Hoc mode, this value can be set. mode region possible channel ====================================== 802.11b-g : 1, 2, 3, 4, 5, 7, 8, 9, 10, 11, 12, 13
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

adhocSecuritySetting		1.3.6.1.4.1.8691.2.13.1.3.4.2.2
OBJECT IDENTIFIER

adhocAuthentication		1.3.6.1.4.1.8691.2.13.1.3.4.2.2.1
Wireless LAN autentication type.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	open-system(0)

adhocEncryption		1.3.6.1.4.1.8691.2.13.1.3.4.2.2.2
Set encryption type.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(0), wep(1)

adhocWepKeyLength		1.3.6.1.4.1.8691.2.13.1.3.4.2.2.3
WEP key length.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	key-64-bits(0), key-128-bits(1)

adhocWepKeyIndex		1.3.6.1.4.1.8691.2.13.1.3.4.2.2.4
WEP key index 1~4.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..4

adhocWepKeyPassphrase		1.3.6.1.4.1.8691.2.13.1.3.4.2.2.5
WEP key passphrase.
Status: current	Access: write-only
OBJECT-TYPE
	DisplayString	Size(1..40)

adhocWepKeyFormat		1.3.6.1.4.1.8691.2.13.1.3.4.2.2.6
WEP key format.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ascii(0), hex(1)

infrastructureProfile		1.3.6.1.4.1.8691.2.13.1.3.4.3
OBJECT IDENTIFIER

infraGeneralSetting		1.3.6.1.4.1.8691.2.13.1.3.4.3.1
OBJECT IDENTIFIER

infraGeneralSettingTable		1.3.6.1.4.1.8691.2.13.1.3.4.3.1.1
WLAN profile general setting table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		InfraGeneralSettingEntry

infraGeneralSettingEntry		1.3.6.1.4.1.8691.2.13.1.3.4.3.1.1.1
WLAN profile general setting entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	InfraGeneralSettingEntry

profileIndex		1.3.6.1.4.1.8691.2.13.1.3.4.3.1.1.1.1
The profile index
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	profile1(1)

profileName		1.3.6.1.4.1.8691.2.13.1.3.4.3.1.1.1.2
Assign profile name.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..32)

profileRFType		1.3.6.1.4.1.8691.2.13.1.3.4.3.1.1.1.3
Select WLAN network type.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	auto(0), w802-11a(1), w802-11b-g(2), w802-11a-n(3), w802-11b-g-n(4)

profileWlanSSID		1.3.6.1.4.1.8691.2.13.1.3.4.3.1.1.1.4
Set WLAN SSID
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..32)

securitySetting		1.3.6.1.4.1.8691.2.13.1.3.4.3.2
OBJECT IDENTIFIER

securitySettingTable		1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1
WLAN profile security setting table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SecuritySettingEntry

securitySettingEntry		1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1
WLAN profile security setting entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	SecuritySettingEntry

authentication		1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.1
Wireless LAN autentication type.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	open-system(0), shared-key(1), wpa(2), wpa-psk(3), wpa2(4), wpa2-psk(5)

encryption		1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.2
Set encryption type. Selection rule is as following. authentication selectable encryption ============== ===================== open-system(0) disable(0), wep(1) shared-key(1) wep(1) wpa(2), wpa-psk(3) tkip(2), aes-ccmp(3) wpa2(4), wpa2-psk(5) tkip(2), aes-ccmp(3)
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(0), wep(1), tkip(2), aes-ccmp(3)

wepKeyLength		1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.3
WEP key length.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	key-64-bits(0), key-128-bits(1)

wepKeyIndex		1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.4
WEP key index 1~4.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..4

wepKeyPassphrase		1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.5
WEP key passphrase.
Status: current	Access: write-only
OBJECT-TYPE
	DisplayString	Size(1..40)

wepKeyFormat		1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.6
WEP key format.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ascii(0), hex(1)

eapMethod		1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.12
EAP method for WPA and WPA2 authentication.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	tls(0), peap(1), ttls(2), leap(3)

tunneledAuth		1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.13
Set tunneled authentication protocol when PEAP/TTLS is selected as EAP method. EAP method selectable tunneled authentication ========== ================================== peap(1) gtc(0), md5(1), mschapv2(5) ttls(2) pap(2), chap(3), mschap(4), mschapv2(5), eap-mschapv2(8), eap-gtc(9), eap-md5(10)
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	gtc(0), md5(1), pap(2), chap(3), mschap(4), mschapv2(5), tls(6), eap-tls(7), eap-mschapv2(8), eap-gtc(9), eap-md5(10)

wpaUsername		1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.14
WPA username for WPA and WPA2 authentication.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..40)

wpaAnonymousUsername		1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.16
Anonymous username needed when TTLS is selected as EAP method.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..40)

verifyServerCert		1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.17
The setting of verify server certificate.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

trustedServerCert		1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.18
Display whether or not trusted server certificate is installed.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	not-installed(0), installed(1)

userCert		1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.19
Display whether or not user certificate is installed.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	not-installed(0), installed(1)

userPrivateKey		1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.20
Display whether or not user private key is installed.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	not-installed(0), installed(1)

fastRoamingSetting		1.3.6.1.4.1.8691.2.13.1.3.4.3.3
The setting of fast roaming.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

fastRoamingScanChannels1		1.3.6.1.4.1.8691.2.13.1.3.4.3.4
The scan channels of fast roaming. 0 represents 'N/A' ====================================================== Auot channel : 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165 802.11a, 802.11a-n : 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165 802.11b-g, 802.11b-g-n : 1, 2, 3, 4, 5, 7, 8, 9, 10, 11, 12, 13
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	n-a(0), channel-1(1), channel-2(2), channel-3(3), channel-4(4), channel-5(5), channel-6(6), channel-7(7), channel-8(8), channel-9(9), channel-10(10), channel-11(11), channel-12(12), channel-13(13), channel-36(15), channel-40(16), channel-44(17), channel-48(18), channel-52(19), channel-56(20), channel-60(21), channel-64(22), channel-100(23), channel-104(24), channel-108(25), channel-112(26), channel-116(27), channel-120(28), channel-124(29), channel-128(30), channel-132(31), channel-136(32), channel-140(33), channel-149(34), channel-153(35), channel-157(36), channel-161(37), channel-165(38)

fastRoamingScanChannels2		1.3.6.1.4.1.8691.2.13.1.3.4.3.5
The scan channels of fast roaming. 0 represents 'N/A' ====================================================== Auot channel : 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165 802.11a, 802.11a-n : 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165 802.11b-g, 802.11b-g-n : 1, 2, 3, 4, 5, 7, 8, 9, 10, 11, 12, 13
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	n-a(0), channel-1(1), channel-2(2), channel-3(3), channel-4(4), channel-5(5), channel-6(6), channel-7(7), channel-8(8), channel-9(9), channel-10(10), channel-11(11), channel-12(12), channel-13(13), channel-36(15), channel-40(16), channel-44(17), channel-48(18), channel-52(19), channel-56(20), channel-60(21), channel-64(22), channel-100(23), channel-104(24), channel-108(25), channel-112(26), channel-116(27), channel-120(28), channel-124(29), channel-128(30), channel-132(31), channel-136(32), channel-140(33), channel-149(34), channel-153(35), channel-157(36), channel-161(37), channel-165(38)

fastRoamingScanChannels3		1.3.6.1.4.1.8691.2.13.1.3.4.3.6
The scan channels of fast roaming. 0 represents 'N/A' ====================================================== Auot channel : 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165 802.11a, 802.11a-n : 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165 802.11b-g, 802.11b-g-n : 1, 2, 3, 4, 5, 7, 8, 9, 10, 11, 12, 13
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	n-a(0), channel-1(1), channel-2(2), channel-3(3), channel-4(4), channel-5(5), channel-6(6), channel-7(7), channel-8(8), channel-9(9), channel-10(10), channel-11(11), channel-12(12), channel-13(13), channel-36(15), channel-40(16), channel-44(17), channel-48(18), channel-52(19), channel-56(20), channel-60(21), channel-64(22), channel-100(23), channel-104(24), channel-108(25), channel-112(26), channel-116(27), channel-120(28), channel-124(29), channel-128(30), channel-132(31), channel-136(32), channel-140(33), channel-149(34), channel-153(35), channel-157(36), channel-161(37), channel-165(38)

fastRoamingThreshold		1.3.6.1.4.1.8691.2.13.1.3.4.3.7
Roaming threshold of fast roaming
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	-70..-40

fastRoamingDifference		1.3.6.1.4.1.8691.2.13.1.3.4.3.8
Roaming difference of fast roaming
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	2..10

wlanLogSetting		1.3.6.1.4.1.8691.2.13.1.3.5
OBJECT IDENTIFIER

wlanLogEnable		1.3.6.1.4.1.8691.2.13.1.3.5.1
Enable or disable WLAN log
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

advancedSetting		1.3.6.1.4.1.8691.2.13.1.3.6
OBJECT IDENTIFIER

gratuitousArp		1.3.6.1.4.1.8691.2.13.1.3.6.1
Enable or disable the gratuitous ARP function. For some applications, users need the NPort W2x50A series device server to send broadcast packets to update the ARP table on the server. If the customer enables this function and sets the send period, the NPort W2x50A series device server will send broadcast packets periodically.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

gratuitousArpSendPeriod		1.3.6.1.4.1.8691.2.13.1.3.6.2
The send period of the gratuitous ARP function. Range: 10 ~ 1000 sec.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	10..1000

gratuitousArpIpAddress1		1.3.6.1.4.1.8691.2.13.1.3.6.3
The IP address of the static gratuitous ARP.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

gratuitousArpMacAddress1		1.3.6.1.4.1.8691.2.13.1.3.6.4
The MAC address of the static gratuitous ARP.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

gratuitousArpIpAddress2		1.3.6.1.4.1.8691.2.13.1.3.6.5
The IP address of the static gratuitous ARP.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

gratuitousArpMacAddress2		1.3.6.1.4.1.8691.2.13.1.3.6.6
The MAC address of the static gratuitous ARP.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

gratuitousArpIpAddress3		1.3.6.1.4.1.8691.2.13.1.3.6.7
The IP address of the static gratuitous ARP.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

gratuitousArpMacAddress3		1.3.6.1.4.1.8691.2.13.1.3.6.8
The MAC address of the static gratuitous ARP.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

gratuitousArpIpAddress4		1.3.6.1.4.1.8691.2.13.1.3.6.9
The IP address of the static gratuitous ARP.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

gratuitousArpMacAddress4		1.3.6.1.4.1.8691.2.13.1.3.6.10
The MAC address of the static gratuitous ARP.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

portSetting		1.3.6.1.4.1.8691.2.13.1.4
OBJECT IDENTIFIER

opModeSetting		1.3.6.1.4.1.8691.2.13.1.4.1
OBJECT IDENTIFIER

opMode		1.3.6.1.4.1.8691.2.13.1.4.1.1
OBJECT IDENTIFIER

opModePortTable		1.3.6.1.4.1.8691.2.13.1.4.1.1.1
The serial ports' operation mode table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		OpModePortEntry

opModePortEntry		1.3.6.1.4.1.8691.2.13.1.4.1.1.1.1
The serial port's operation mode entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	OpModePortEntry

portIndex		1.3.6.1.4.1.8691.2.13.1.4.1.1.1.1.1
The serial port index.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..1

portMode		1.3.6.1.4.1.8691.2.13.1.4.1.1.1.1.2
The operation mode of the serial port. Note that changing this setting may also change the application.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	pair-connection-slave(0), pair-connection-master(1), real-Com(2), disable(7), tcp-Server(10), ethernet-modem(12), tcp-Client(13), udp(14), rfc-2217(20), reverse-Terminal(21)

opModeParam		1.3.6.1.4.1.8691.2.13.1.4.1.2
OBJECT IDENTIFIER

realCOM		1.3.6.1.4.1.8691.2.13.1.4.1.2.1
OBJECT IDENTIFIER

realCOMTable		1.3.6.1.4.1.8691.2.13.1.4.1.2.1.1
The Real COM mode table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RealCOMEntry

realCOMEntry		1.3.6.1.4.1.8691.2.13.1.4.1.2.1.1.1
The Real COM mode entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	RealCOMEntry

realCOMTcpAliveCheck		1.3.6.1.4.1.8691.2.13.1.4.1.2.1.1.1.1
The TCP alive check time. 0 min: TCP connection will not be closed when the TCP connection is idle. 1 to 99 min: The NPort W2x50A series device server automatically closes the TCP connection if there is no TCP activity for the given time. After the connection is closed, the NPort W2x50A series device server starts listening for another Real COM driver Connection.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

realCOMMaxConnection		1.3.6.1.4.1.8691.2.13.1.4.1.2.1.1.1.2
Max connection is usually used when the user needs to receive data from different hosts simultaneously. The factory default is 1. In this case, only one specific host can access this port of the NPort W2x50A series device server, and the Real COM driver on that host will have full control over the port. Max. connection = 1: Allows only a single host's Real COM driver to open the specific NPort W2x50A series device server's serial port. Max connection = 2 to 8: Allows 2 to 8 hosts' Real COM drivers to open the specific NPort W2x50A series device server's serial port, at the same time. When multiple hosts' Real COM drivers open the serial port at the same time, the COM driver only provides a pure data tunnel without control ability. The serial port parameter will use the firmware settings instead of getting the settings from your application program (AP).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

realCOMIgnoreJammedIp		1.3.6.1.4.1.8691.2.13.1.4.1.2.1.1.1.3
Previously, when Max connection was set to a value greater than 1, and the serial device was transmitting data, if any one of the connected hosts stopped responding, the serial device would wait until the data had been transmitted successfully before transmitting the second group of data to all hosts. Currently, if you select Yes for 'Ignore jammed IP,' the host that is not responding will be ignored, but the data will still be transmitted to the other hosts.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

realCOMAllowDriverControl		1.3.6.1.4.1.8691.2.13.1.4.1.2.1.1.1.4
If Max connection is greater than 1, NPort will ignore driver control commands from all connected hosts. However, if you set Allow driver control to YES, control commands will be accepted. Note that since the NPort W2x50A series device server may get configuration changes from multiple hosts, the most recent command received will take precedence.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

realCOMConnectionDownRTS		1.3.6.1.4.1.8691.2.13.1.4.1.2.1.1.1.5
For some applications, serial devices must obtain the Ethernet link status by reading the RTS signal from the NPort W2x50A series device server. If this setting is set to 'always low,' RTS will change its state to low if the Ethernet link is off.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	always-low(1), always-high(0)

realCOMConnectionDownDTR		1.3.6.1.4.1.8691.2.13.1.4.1.2.1.1.1.6
For some applications, serial devices must obtain the Ethernet link status by reading the DTR signal from the NPort W2x50A series device server. If this setting is set to 'always low,' DTR will change its state to low if the Ethernet link is off.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	always-low(1), always-high(0)

rfc2217		1.3.6.1.4.1.8691.2.13.1.4.1.2.2
OBJECT IDENTIFIER

rfc2217Table		1.3.6.1.4.1.8691.2.13.1.4.1.2.2.1
The RFC2217 mode table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Rfc2217Entry

rfc2217Entry		1.3.6.1.4.1.8691.2.13.1.4.1.2.2.1.1
The RFC2217 mode entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	Rfc2217Entry

rfc2217TcpAliveCheck		1.3.6.1.4.1.8691.2.13.1.4.1.2.2.1.1.1
The TCP alive check time. 0 min: TCP connection will not be closed when the TCP connection is idle. 1 to 99 min: The NPort W2x50A series device server automatically closes the TCP connection if there is no TCP activity for the given time. After the connection is closed, the NPort W2x50A series device server starts listening for another TCP Connection.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

rfc2217TcpPort		1.3.6.1.4.1.8691.2.13.1.4.1.2.2.1.1.2
TCP server port of RFC2217.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

tcpServer		1.3.6.1.4.1.8691.2.13.1.4.1.2.3
OBJECT IDENTIFIER

tcpServerTable		1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1
The TCP server mode table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TcpServerEntry

tcpServerEntry		1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1
The TCP server mode entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	TcpServerEntry

tcpServerTcpAliveCheck		1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1.1
The TCP alive check time. 0 min: TCP connection will not be closed when the TCP connection is idle. 1 to 99 min: The NPort W2x50A series device server automatically closes the TCP connection if there is no TCP activity for the given time. After the connection is closed, the NPort W2x50A series device server starts listening for another TCP Connection.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

tcpServerInactivityTime		1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1.2
0 ms: TCP connection is not closed when the serial line is idle. 1-65535 ms: The NPort W2x50A series device server automatically closes the TCP connection if there is no serial data activity for the given time. After the connection is closed, the NPort W2x50A series device server starts listening for another TCP connection.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

tcpServerMaxConnection		1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1.3
Max connection is usually used when the user needs to receive data from different hosts simultaneously. The factory default is 1. In this case, only one specific host can access this port of the NPort W2x50A series device server, and the TCP server driver on that host will have full control over the port. Max. connection 1: Allows only a single host's to connect specific NPort W2x50A series device Max connection 2 to 8: Allows 2 to 8 hosts' to conncect NPort W2x50A series device at the same time.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

tcpServerIgnoreJammedIp		1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1.4
Previously, when Max connection was set to a value greater than 1, and the serial device was transmitting data, if any one of the connected hosts stopped responding, the serial device would wait until the data had been transmitted successfully before transmitting the second group of data to all hosts. Currently, if you select Yes for 'Ignore jammed IP,' the host that is not responding will be ignored, but the data will still be transmitted to the other hosts.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

tcpServerAllowDriverControl		1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1.5
If Max connection is greater than 1, NPort will ignore driver control commands from all connected hosts. However, if you set Allow driver control to YES, control commands will be accepted. Note that since the NPort W2x50A series device server may get configuration changes from multiple hosts, the most recent command received will take precedence.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

tcpServerTcpPort		1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1.6
The 'TCP port' is the TCP port that the NPort W2x50A series device server uses to listen to connections, and that other devices must use to contact the NPort W2x50A series device server.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

tcpServerCmdPort		1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1.7
The 'Command port' is a TCP port used to listen for SSDK commands from the host. In order to prevent a TCP port conflict with other applications, the user can set the Command port to another port if needed.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

tcpServerConnectionDownRTS		1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1.8
For some applications, serial devices must obtain the Ethernet link status from the RTS signal sent by the NPort W2x50A series device server. If this setting is set to 'goes low,' RTS will change the state to low if the Ethernet link is off.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	always-low(1), always-high(0)

tcpServerConnectionDownDTR		1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1.9
For some applications, serial devices must obtain the Ethernet link status from the DTR signal sent by the NPort W2x50A series device server. If this setting is set to 'goes low,' DTR will change the state to low if the Ethernet link is off.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	always-low(1), always-high(0)

tcpClient		1.3.6.1.4.1.8691.2.13.1.4.1.2.4
OBJECT IDENTIFIER

tcpClientTable		1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1
The TCP client mode table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TcpClientEntry

tcpClientEntry		1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1
The TCP client mode entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	TcpClientEntry

tcpClientTcpAliveCheck		1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.1
The TCP alive check time. 0 min: TCP connection will not be closed when the TCP connection is idle. 1 to 99 min: The NPort W2x50A series device client automatically closes the TCP connection if there is no TCP activity for the given time.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

tcpClientInactivityTime		1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.2
0 ms: TCP connection is not closed when the serial line is idle. 1-65535 ms: The NPort W2x50A series device client automatically closes the TCP connection if there is no serial data activity for the given time.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

tcpClientIgnoreJammedIp		1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.3
Previously, when Max connection was set to a value greater than 1, and the serial device was transmitting data, if any one of the connected hosts stopped responding, the serial device would wait until the data had been transmitted successfully before transmitting the second group of data to all hosts. Currently, if you select Yes for 'Ignore jammed IP,' the host that is not responding will be ignored, but the data will still be transmitted to the other hosts.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

tcpClientDestinationAddress1		1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.4
The NPort W2x50A series device server can connect actively to a remote host that has this IP address.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

tcpClientDestinationPort1		1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.5
The NPort W2x50A series device server can connect actively to a remote host that has this TCP port number.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

tcpClientDestinationAddress2		1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.6
The NPort W2x50A series device server can connect actively to a remote host that has this IP address.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

tcpClientDestinationPort2		1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.7
The NPort W2x50A series device server can connect actively to a remote host that has this TCP port number.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

tcpClientDestinationAddress3		1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.8
The NPort W2x50A series device server can connect actively to a remote host that has this IP address.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

tcpClientDestinationPort3		1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.9
The NPort W2x50A series device server can connect actively to a remote host that has this port number.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

tcpClientDestinationAddress4		1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.10
The NPort W2x50A series device server can connect actively to a remote host that has this IP address.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

tcpClientDestinationPort4		1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.11
The NPort W2x50A series device server can connect actively to a remote host that has this port number.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

tcpClientDesignatedLocalPort1		1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.12
The local TCP port used to connect actively to the remote host.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

tcpClientDesignatedLocalPort2		1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.13
The local TCP port used to connect actively to the remote host.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

tcpClientDesignatedLocalPort3		1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.14
The local TCP port used to connect actively to the remote host.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

tcpClientDesignatedLocalPort4		1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.15
The local TCP port used to connect actively to the remote host.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

tcpClientConnectionControl		1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.16
Events that cause the TCP client to drop the connection.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	startup-None(257), anyCharacter-None(258), anyCharacter-InactivityTime(514), dsrOn-DSR-Off(1028), dsrOn-None(260), dcdOn-DCD-Off(2056), dcdOn-None(264)

udp		1.3.6.1.4.1.8691.2.13.1.4.1.2.5
OBJECT IDENTIFIER

udpTable		14.1
The UDP mode table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		UdpEntry

udpEntry		14.1.1
The UDP mode entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	UdpEntry

udpDestinationAddress1Begin		14.1.1.1
The NPort W2x50A series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between this parameter and udpDestinationAddress1End.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

udpDestinationAddress1End		14.1.1.2
The NPort W2x50A series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between udpDestinationAddress1Begin and this parameter.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

udpDestinationPort1		14.1.1.3
The NPort W2x50A series device server can actively send UDP packets to remote hosts that have this UDP port number.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

udpDestinationAddress2Begin		14.1.1.4
The NPort W2x50A series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between this parameter and udpDestinationAddress2End.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

udpDestinationAddress2End		14.1.1.5
The NPort W2x50A series device server can actively send UDP packets to the remote hosts whose IP addresses are in the range between udpDestinationAddress2Begin and this parameter.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

udpDestinationPort2		14.1.1.6
The NPort W2x50A series device server can actively send UDP packets to the remote hosts that have this UDP port number.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

udpDestinationAddress3Begin		14.1.1.7
The NPort W2x50A series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between this parameter and udpDestinationAddress3End.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

udpDestinationAddress3End		14.1.1.8
The NPort W2x50A series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between udpDestinationAddress3Begin and this parameter.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

udpDestinationPort3		14.1.1.9
The NPort W2x50A series device server can actively send UDP packets to remote hosts that have this UDP port number.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

udpDestinationAddress4Begin		14.1.1.10
The NPort W2x50A series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between this parameter and udpDestinationAddress4End.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

udpDestinationAddress4End		14.1.1.11
The NPort W2x50A series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between udpDestinationAddress4Begin and this parameter.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

udpDestinationPort4		14.1.1.12
The NPort W2x50A series device server can actively send UDP packets to remote hosts that have this UDP port number.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

udpLocalListenPort		14.1.1.13
The UDP port that the NPort W2x50A series device server listens to and that other devices must use to contact the NPort W2x50A series device server.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

pairConnectionMaster		1.3.6.1.4.1.8691.2.13.1.4.1.2.6
OBJECT IDENTIFIER

pairConnectionMasterTable		1.3.6.1.4.1.8691.2.13.1.4.1.2.6.1
The pair connection master mode table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PairConnectionMasterEntry

pairConnectionMasterEntry		1.3.6.1.4.1.8691.2.13.1.4.1.2.6.1.1
The pair connection master mode entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	PairConnectionMasterEntry

pairConnectionMasterTcpAliveCheck		1.3.6.1.4.1.8691.2.13.1.4.1.2.6.1.1.1
The TCP alive check time. 0 min: TCP connection will not be closed when the TCP connection is idle. 1 to 99 min: The NPort W2x50A series device server automatically closes the TCP connection if there is no TCP activity for the given time. After the connection is closed, the NPort W2x50A series device server starts connecting again.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

pairConnectionMasterDestnationAddress		1.3.6.1.4.1.8691.2.13.1.4.1.2.6.1.1.2
IP address of pair connection slave.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

pairConnectionMasterDestnationTcpPort		1.3.6.1.4.1.8691.2.13.1.4.1.2.6.1.1.3
TCP port of pair connection slave.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

pairConnectionSlave		1.3.6.1.4.1.8691.2.13.1.4.1.2.7
OBJECT IDENTIFIER

pairConnectionSlaveTable		1.3.6.1.4.1.8691.2.13.1.4.1.2.7.1
The pair connection slave mode table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PairConnectionSlaveEntry

pairConnectionSlaveEntry		1.3.6.1.4.1.8691.2.13.1.4.1.2.7.1.1
The pair connection slave mode entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	PairConnectionSlaveEntry

pairConnectionSlaveTcpAliveCheck		1.3.6.1.4.1.8691.2.13.1.4.1.2.7.1.1.1
The TCP alive check time. 0 min: TCP connection will not be closed when the TCP connection is idle. 1 to 99 min: The NPort W2x50A series device server automatically closes the TCP connection if there is no TCP activity for the given time. After the connection is closed, the NPort W2x50A series device server starts listening for another TCP Connection.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

pairConnectionSlaveLocalTcpPort		1.3.6.1.4.1.8691.2.13.1.4.1.2.7.1.1.2
TCP server port of pair connection slave.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

ethernetModem		1.3.6.1.4.1.8691.2.13.1.4.1.2.8
OBJECT IDENTIFIER

ethernetModemTable		1.3.6.1.4.1.8691.2.13.1.4.1.2.8.1
The ethernet modem mode table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		EthernetModemEntry

ethernetModemEntry		1.3.6.1.4.1.8691.2.13.1.4.1.2.8.1.1
The ethernet modem mode entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	EthernetModemEntry

ethernetModemTcpAliveCheck		1.3.6.1.4.1.8691.2.13.1.4.1.2.8.1.1.1
The TCP alive check time. 0 min: TCP connection will not be closed when the TCP connection is idle. 1 to 99 min: The NPort W2x50A series device server automatically closes the TCP connection if there is no TCP activity for the given time.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

ethernetModemLocalTcpPort		1.3.6.1.4.1.8691.2.13.1.4.1.2.8.1.1.2
TCP server port of ethernet modem.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

reverseTerminal		1.3.6.1.4.1.8691.2.13.1.4.1.2.9
OBJECT IDENTIFIER

reverseTerminalTable		1.3.6.1.4.1.8691.2.13.1.4.1.2.9.1
The reverse terminal mode table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ReverseTerminalEntry

reverseTerminalEntry		1.3.6.1.4.1.8691.2.13.1.4.1.2.9.1.1
The reverse terminal mode entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	ReverseTerminalEntry

reverseTerminalTcpAliveCheck		1.3.6.1.4.1.8691.2.13.1.4.1.2.9.1.1.1
The TCP alive check time. 0 min: TCP connection will not be closed when the TCP connection is idle. 1 to 99 min: The NPort W2x50A series device server automatically closes the TCP connection if there is no TCP activity for the given time.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

reverseTerminalInactivityTime		1.3.6.1.4.1.8691.2.13.1.4.1.2.9.1.1.2
0 min: TCP connection is not closed when the serial line is idle. 0-99 min: The NPort W2x50A series device server automatically closes the TCP connection if there is no serial data activity for the given time. After the connection is closed, the NPort W2x50P series device server starts listening for another TCP connection.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

reverseTerminalTcpPort		1.3.6.1.4.1.8691.2.13.1.4.1.2.9.1.1.3
Each of the NPort W2x50A series device server's serial ports are mapped to a TCP port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

reverseTerminalAuthenticationType		1.3.6.1.4.1.8691.2.13.1.4.1.2.9.1.1.4
The reverse terminal authentication type.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(0), local(1), radius(2)

reverseTerminalMapKeys		1.3.6.1.4.1.8691.2.13.1.4.1.2.9.1.1.5
If data received through NPort W2x50A series device server's Ethernet port is sent using the 'enter' command, the data will be transmitted out through the serial port with an added 1. 'carriage return + line feed' if you select the 'cr-lf' option (i.e., the cursor will jump to the next line, and return to the first character of the line) 2. 'carriage return' if you select the 'cr' option (i.e., the cursor will return to the first character of the line 3. 'line feed' if you select the 'lf' option. (i.e., the cursor will jump to the next line, but not move horizontally)
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	cr-lf(0), cr(1), lf(2)

dataPacking		1.3.6.1.4.1.8691.2.13.1.4.1.3
OBJECT IDENTIFIER

dataPackingPortTable		1.3.6.1.4.1.8691.2.13.1.4.1.3.1
The Data Packing table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		DataPackingPortEntry

dataPackingPortEntry		1.3.6.1.4.1.8691.2.13.1.4.1.3.1.1
The Data Packing entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	DataPackingPortEntry

portPacketLength		1.3.6.1.4.1.8691.2.13.1.4.1.3.1.1.1
If the value is 0, the Delimiter Process will be used, regardless of the length of the data packet. If the data length (in bytes) matches the configured value, the data will be forced out. The data length can be configured from 0 to 1024 bytes. Set to 0 if you do not need to limit the length.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

portDelimiter1Enable		1.3.6.1.4.1.8691.2.13.1.4.1.3.1.1.2
Enable the first delimiter character.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

portDelimiter1		1.3.6.1.4.1.8691.2.13.1.4.1.3.1.1.3
The first delimiter character, in hex decimal.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..2)

portDelimiter2Enable		1.3.6.1.4.1.8691.2.13.1.4.1.3.1.1.4
Enable the second delimiter character.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

portDelimiter2		1.3.6.1.4.1.8691.2.13.1.4.1.3.1.1.5
The second delimiter character, in hex decimal.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..2)

portDelimiterProcess		1.3.6.1.4.1.8691.2.13.1.4.1.3.1.1.6
'delimiterAddOne' or 'delimiterAddTwo': The data will be transmitted when an additional byte (for 'delimiterAddOne'), or an additional 2 bytes (for 'delimiterAddTwo') of data is received after receiving the Delimiter. 'stripDelimiter': When the delimiter is received, the Delimiter is deleted (i.e., stripped), and the remaining data is transmitted. 'doNothing': The data will be transmitted when the delimiter is received.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	doNothing(1), delimiterAddOne(2), delimiterAddTwo(4), stripDelimiter(8)

portForceTransmit		1.3.6.1.4.1.8691.2.13.1.4.1.3.1.1.7
0: Disable the force transmit timeout. 1 to 65535: Forces the NPort W2x50A series device server's TCP/IP protocol software to try to pack serial data received during the specified time into the same data frame.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

comParamSetting		1.3.6.1.4.1.8691.2.13.1.4.2
OBJECT IDENTIFIER

comParamPortTable		1.3.6.1.4.1.8691.2.13.1.4.2.1
The Communication Parameters table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ComParamPortEntry

comParamPortEntry		1.3.6.1.4.1.8691.2.13.1.4.2.1.1
The Communication Parameters entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	ComParamPortEntry

portAlias		1.3.6.1.4.1.8691.2.13.1.4.2.1.1.1
Port alias is included to allow easy identification of the serial devices that are connected to NPort W2x50A series device server's serial port.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..16)

portInterface		1.3.6.1.4.1.8691.2.13.1.4.2.1.1.2
The serial interface that the port works on.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	rs-232(0), rs-422(1), rs-485-2wire(2), rs-485-4wire(3)

portBaudRate		1.3.6.1.4.1.8691.2.13.1.4.2.1.1.3
The port's speed in bits per second. You can choose a standard baud rate by indexing.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	b50(0), b75(1), b110(2), b134(3), b150(4), b300(5), b600(6), b1200(7), b1800(8), b2400(9), b4800(10), b9600(12), b19200(13), b38400(14), b57600(15), b115200(16), b230400(17), b460800(18), b921600(19)

portDataBits		1.3.6.1.4.1.8691.2.13.1.4.2.1.1.4
The number of bits in a character for the port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	bits-5(0), bits-6(1), bits-7(2), bits-8(3)

portStopBits		1.3.6.1.4.1.8691.2.13.1.4.2.1.1.5
The number of stop bits for the port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	bits-1(0), bits-1dot5(1), bits-2(2)

portParity		1.3.6.1.4.1.8691.2.13.1.4.2.1.1.6
The parity bit for the port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(0), odd(1), even(3), mark(5), space(7)

portFlowControl		1.3.6.1.4.1.8691.2.13.1.4.2.1.1.7
The flow-control method for the port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(0), rts-cts(1), xon-xoff(2)

portFIFO		1.3.6.1.4.1.8691.2.13.1.4.2.1.1.8
Enable or disable the port's FIFO.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

dataBuffering		1.3.6.1.4.1.8691.2.13.1.4.3
OBJECT IDENTIFIER

dataBufferingPortTable		1.3.6.1.4.1.8691.2.13.1.4.3.1
The Data Buffering table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		DataBufferingPortEntry

dataBufferingPortEntry		1.3.6.1.4.1.8691.2.13.1.4.3.1.1
The Data Buffering entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	DataBufferingPortEntry

portBufferingEnable		1.3.6.1.4.1.8691.2.13.1.4.3.1.1.1
Enable off-line port buffering.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

portSerialDataLoggingEnable		1.3.6.1.4.1.8691.2.13.1.4.3.1.1.2
Enable or disable serial data logging for the port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

sysManagement		1.3.6.1.4.1.8691.2.13.1.5
OBJECT IDENTIFIER

miscNetworkSettings		1.3.6.1.4.1.8691.2.13.1.5.1
OBJECT IDENTIFIER

accessibleIp		1.3.6.1.4.1.8691.2.13.1.5.1.1
OBJECT IDENTIFIER

enableAccessibleIpList		1.3.6.1.4.1.8691.2.13.1.5.1.1.1
Enable or disable the entire accessible IP list.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

accessibleIpListTable		1.3.6.1.4.1.8691.2.13.1.5.1.1.2
Accessible IP List table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AccessibleIpListEntry

accessibleIpListEntry		1.3.6.1.4.1.8691.2.13.1.5.1.1.2.1
Accessible IP List entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	AccessibleIpListEntry

accessibleIpListIndex		1.3.6.1.4.1.8691.2.13.1.5.1.1.2.1.1
Accessible IP List index.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..16

activeAccessibleIpList		1.3.6.1.4.1.8691.2.13.1.5.1.1.2.1.2
Enable or disable this accessible IP entry.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

accessibleIpListAddress		1.3.6.1.4.1.8691.2.13.1.5.1.1.2.1.3
Accessible IP address. This value can be the IP address of a single host if the netmask is set to '255.255.255.255,' or it can be a network address.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

accessibleIpListNetmask		1.3.6.1.4.1.8691.2.13.1.5.1.1.2.1.4
Accessible IP address netmask. The IP address and netmask are used to specify a group of remote hosts.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

snmpAgentSettings		1.3.6.1.4.1.8691.2.13.1.5.1.2
OBJECT IDENTIFIER

snmpEnable		1.3.6.1.4.1.8691.2.13.1.5.1.2.1
Enable or disable SNMP agent.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

snmpContactName		1.3.6.1.4.1.8691.2.13.1.5.1.2.2
The SNMP contact information usually includes an emergency contact name and telephone or pager number.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..40)

snmpLocation		1.3.6.1.4.1.8691.2.13.1.5.1.2.3
Specify the location string for SNMP agents, such as the NPort W2x50A series device server. This string is usually set to the street address where the NPort W2x50A series device server is physically located.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..40)

authenticationServer		1.3.6.1.4.1.8691.2.13.1.5.1.4
OBJECT IDENTIFIER

radiusServerIp		1.3.6.1.4.1.8691.2.13.1.5.1.4.1
The IP address or domain name of the RADIUS server.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..40)

udpPortAuthenticationServer		1.3.6.1.4.1.8691.2.13.1.5.1.4.3
The UDP port of the RADIUS server.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	port1645(1645), port1812(1812)

radiusAccounting		1.3.6.1.4.1.8691.2.13.1.5.1.4.4
Enable or disable RADIUS accounting.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

sysLogSettings		1.3.6.1.4.1.8691.2.13.1.5.1.5
OBJECT IDENTIFIER

sysLocalLog		1.3.6.1.4.1.8691.2.13.1.5.1.5.1
System cold start, System warm start.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

networkLocalLog		1.3.6.1.4.1.8691.2.13.1.5.1.5.2
DHCP/BOOTP get IP/renew, mail fail, NTP connect fail, IP conflict, network link down.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

configLocalLog		1.3.6.1.4.1.8691.2.13.1.5.1.5.3
Login fail, IP changed, password changed, firmware upgrade, SSL certificate import, config export, wireless certificate import, serial data log export.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

opModeLocalLog		1.3.6.1.4.1.8691.2.13.1.5.1.5.4
Connect, Disconnect, Restart.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

autoWarningSettings		1.3.6.1.4.1.8691.2.13.1.5.2
OBJECT IDENTIFIER

eventSettings		1.3.6.1.4.1.8691.2.13.1.5.2.1
OBJECT IDENTIFIER

mailWarningColdStart		1.3.6.1.4.1.8691.2.13.1.5.2.1.1
Refers to starting the system from power off (contrast this with warm start). When performing a cold start, the NPort W2x50A series device server will automatically issue an auto warning message by e-mail after booting up.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

mailWarningWarmStart		1.3.6.1.4.1.8691.2.13.1.5.2.1.2
Refers to restarting the NPort W2x50A without turning the power off. When performing a warm start, the NPort W2x50A series device server will automatically send an e-mail after rebooting.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

mailWarningAuthFailure		1.3.6.1.4.1.8691.2.13.1.5.2.1.3
The user inputs a wrong password from the Console or Administrator. When authentication failure occurs, the NPort W2x50A series device server will immediately send an e-mail.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

mailWarningIpChanged		1.3.6.1.4.1.8691.2.13.1.5.2.1.4
The user has changed the NPort W2x50A series device server's IP address. When the IP address changes,the NPort W2x50A series device server will send an e-mail with the new IP address before it reboots. If the NPort W2x50A series device server is unable to send an e-mail message to the mail server within 15 seconds, it will reboot anyway, and abort the e-mail auto warning.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

mailWarningPasswordChanged		1.3.6.1.4.1.8691.2.13.1.5.2.1.5
The user has changed the NPort W2x50A series device server's password. When the password changes, the NPort W2x50A series device server will send an e-mail with the password changed notice before it reboots. If the NPort W2x50A series device server is unable to send an e-mail message to the mail server within 15 seconds, it will reboot anyway, and abort the e-mail auto warning.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

trapServerColdStart		1.3.6.1.4.1.8691.2.13.1.5.2.1.6
Refers to starting the system from power off (contrast this with warm start). When performing a cold start, the NPort W2x50A series device server will automatically issue an auto warning message by sending an SNMP trap after booting up.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

trapServerWarmStart		1.3.6.1.4.1.8691.2.13.1.5.2.1.7
Refers to restarting the NPort W2x50A without turning the power off. When performing a warm start, the NPort W2x50A series device server will automatically send an SNMP trap after rebooting.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

trapServerAuthFailure		1.3.6.1.4.1.8691.2.13.1.5.2.1.8
The user inputs a wrong password from the Console or Administrator. When authentication failure occurs, the NPort W2x50A series device server will immediately send an SNMP trap.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

serialEventSettings		1.3.6.1.4.1.8691.2.13.1.5.2.2
OBJECT IDENTIFIER

portEventSettingsTable		1.3.6.1.4.1.8691.2.13.1.5.2.2.1
Port Event Settings Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PortEventSettingsEntry

portEventSettingsEntry		1.3.6.1.4.1.8691.2.13.1.5.2.2.1.1
Port Event Settings entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	PortEventSettingsEntry

mailDCDchange		1.3.6.1.4.1.8691.2.13.1.5.2.2.1.1.1
A change in the DCD (Data Carrier Detect) signal indicates that the modem connection status has changed. For example, if the DCD signal changes to low, it indicates that the connection line is down. When the DCD signal changes to low, the NPort W2x50A series device server will immediately send an e-mail message.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

trapDCDchange		1.3.6.1.4.1.8691.2.13.1.5.2.2.1.1.2
A change in the DCD (Data Carrier Detect) signal indicates that the modem connection status has changed. For example, if the DCD signal changes to low, it indicates that the connection line is down. When the DCD signal changes to low, the NPort W2x50A series device server will immediately send an SNMP trap.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

mailDSRchange		1.3.6.1.4.1.8691.2.13.1.5.2.2.1.1.3
A change in the DSR (Data Set Ready) signal indicates that the data communication equipment is powered off. For example, if the DSR signal changes to low, it indicates that the data communication equipment is powered down. When the DSR signal changes to low, the NPort W2x50A series device server will immediately send an e-mail message.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

trapDSRchange		1.3.6.1.4.1.8691.2.13.1.5.2.2.1.1.4
A change in the DSR (Data Set Ready) signal indicates that the data communication equipment is powered off. For example, if the DSR signal changes to low, it indicates that the data communication equipment is powered down. When the DSR signal changes to low, the NPort W2x50A series device server will immediately send an SNMP trap.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

emailAlert		1.3.6.1.4.1.8691.2.13.1.5.2.3
OBJECT IDENTIFIER

emailWarningMailServer		1.3.6.1.4.1.8691.2.13.1.5.2.3.1
The e-mail server's IP address or domain name of the e-mail warning function.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

emailRequiresAuthentication		1.3.6.1.4.1.8691.2.13.1.5.2.3.2
Set if the mail server requires user login.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	non-require(0), require(1)

emailWarningUserName		1.3.6.1.4.1.8691.2.13.1.5.2.3.3
The user name used to log into the mail server if authentication is required.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

emailWarningFromEmail		1.3.6.1.4.1.8691.2.13.1.5.2.3.5
The e-mail address to be filled in the 'From' field of the auto-warning e-mail.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

emailWarningFirstEmailAddr		1.3.6.1.4.1.8691.2.13.1.5.2.3.6
The first email address to where the auto-warning e-mail is to be sent.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

emailWarningSecondEmailAddr		1.3.6.1.4.1.8691.2.13.1.5.2.3.7
The second email address to where the auto-warning e-mail is to be sent.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

emailWarningThirdEmailAddr		1.3.6.1.4.1.8691.2.13.1.5.2.3.8
The third email address to where the auto-warning e-mail is to be sent.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

emailWarningFourthEmailAddr		1.3.6.1.4.1.8691.2.13.1.5.2.3.9
The fourth email address to where the auto-warning e-mail is to be sent.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

snmpTrap		1.3.6.1.4.1.8691.2.13.1.5.2.4
OBJECT IDENTIFIER

snmpTrapReceiverIp		1.3.6.1.4.1.8691.2.13.1.5.2.4.1
SNMP trap server IP address or domain name.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

trapVersion		1.3.6.1.4.1.8691.2.13.1.5.2.4.2
SNMP trap version used for the auto-warning function.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	v1(0), v2c(1)

maintenance		1.3.6.1.4.1.8691.2.13.1.5.3
OBJECT IDENTIFIER

consoleSettings		1.3.6.1.4.1.8691.2.13.1.5.3.1
OBJECT IDENTIFIER

httpConsole		1.3.6.1.4.1.8691.2.13.1.5.3.1.1
Enable or disable HTTP console.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

httpsConsole		1.3.6.1.4.1.8691.2.13.1.5.3.1.2
Enable or disable HTTPS console.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

telnetConsole		1.3.6.1.4.1.8691.2.13.1.5.3.1.3
Enable or disable Telnet console.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

sshConsole		1.3.6.1.4.1.8691.2.13.1.5.3.1.4
Enable or disable SSH console.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

serialConsole		1.3.6.1.4.1.8691.2.13.1.5.3.1.5
Enable or disable Serial console.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

resetButton		1.3.6.1.4.1.8691.2.13.1.5.3.1.6
Reset button setting.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable-after-60-sec(0), always-enable(1)

loadFactoryDefault		1.3.6.1.4.1.8691.2.13.1.5.3.2
OBJECT IDENTIFIER

loadFactoryDefaultSetting		1.3.6.1.4.1.8691.2.13.1.5.3.2.1
This function will reset all of the NPort W2x50A series device server's settings to the factory default values. Be aware that previous settings will be lost. Selecting Reset to factory default (excluding IP configuration) will reset all settings except the IP configuration to factory defaults. Selecting Reset to factory default will reset all settings including the IP configuration to factory defaults.
Status: current	Access: write-only
OBJECT-TYPE
	INTEGER	resetToFactoryDefault-ExcludingIpConfiguration(0), resetToFactoryDefault(1)

sysStatus		1.3.6.1.4.1.8691.2.13.1.6
OBJECT IDENTIFIER

s2eConnections		1.3.6.1.4.1.8691.2.13.1.6.1
OBJECT IDENTIFIER

monitorRemoteIpTable		1.3.6.1.4.1.8691.2.13.1.6.1.1
Serial to Network Connections Remote IP table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MonitorRemoteIpEntry

monitorRemoteIpEntry		1.3.6.1.4.1.8691.2.13.1.6.1.1.1
Serial to Network Connections Remote IP entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	MonitorRemoteIpEntry

remoteIpIndex		1.3.6.1.4.1.8691.2.13.1.6.1.1.1.1
Serial to Network Connections Remote IP index.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..8

monitorRemoteIp		1.3.6.1.4.1.8691.2.13.1.6.1.1.1.2
The remote IP currently connecting to this port.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

serialPortStatus		1.3.6.1.4.1.8691.2.13.1.6.2
OBJECT IDENTIFIER

monitorSerialPortStatusTable		1.3.6.1.4.1.8691.2.13.1.6.2.1
Serial Port Status table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MonitorSerialPortStatusEntry

monitorSerialPortStatusEntry		1.3.6.1.4.1.8691.2.13.1.6.2.1.1
Serial Port Status entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	MonitorSerialPortStatusEntry

monitorTxCount		1.3.6.1.4.1.8691.2.13.1.6.2.1.1.1
View the number of bytes transmitted from the port since the last time the port was initialized.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

monitorRxCount		1.3.6.1.4.1.8691.2.13.1.6.2.1.1.2
View the number of bytes received by the port since the last time the port was initialized.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

monitorTxTotalCount		1.3.6.1.4.1.8691.2.13.1.6.2.1.1.3
View the number of bytes transmitted from the port since the last time the system was initialized.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

monitorRxTotalCount		1.3.6.1.4.1.8691.2.13.1.6.2.1.1.4
View the number of bytes received by the port since the last time the system was initialized.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

monitorDSR		1.3.6.1.4.1.8691.2.13.1.6.2.1.1.5
View the current DSR status of this port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

monitorDTR		1.3.6.1.4.1.8691.2.13.1.6.2.1.1.6
View the current DTR status of this port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

monitorRTS		1.3.6.1.4.1.8691.2.13.1.6.2.1.1.7
View the current RTS status of this port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

monitorCTS		1.3.6.1.4.1.8691.2.13.1.6.2.1.1.8
View the current CTS status of this port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

monitorDCD		1.3.6.1.4.1.8691.2.13.1.6.2.1.1.9
View the current DCD status of this port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

serialPortErrorCount		1.3.6.1.4.1.8691.2.13.1.6.3
OBJECT IDENTIFIER

monitorSerialPortErrorCountTable		1.3.6.1.4.1.8691.2.13.1.6.3.1
Serial Port Error Count table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MonitorSerialPortErrorCountEntry

monitorSerialPortErrorCountEntry		1.3.6.1.4.1.8691.2.13.1.6.3.1.1
Serial Port Error Count entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	MonitorSerialPortErrorCountEntry

monitorErrorCountFrame		1.3.6.1.4.1.8691.2.13.1.6.3.1.1.1
View the number of 'Frame' errors for this port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

monitorErrorCountParity		1.3.6.1.4.1.8691.2.13.1.6.3.1.1.2
View the number of 'Parity' errors for this port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

monitorErrorCountOverrun		1.3.6.1.4.1.8691.2.13.1.6.3.1.1.3
View the number of 'Overrun' errors for this port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

monitorErrorCountBreak		1.3.6.1.4.1.8691.2.13.1.6.3.1.1.4
View the number of 'Break' errors for this port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

serialPortSettings		1.3.6.1.4.1.8691.2.13.1.6.4
OBJECT IDENTIFIER

monitorSerialPortSettingsTable		1.3.6.1.4.1.8691.2.13.1.6.4.1
Serial Port Settings table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MonitorSerialPortSettingsEntry

monitorSerialPortSettingsEntry		1.3.6.1.4.1.8691.2.13.1.6.4.1.1
Serial Port Settings entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	MonitorSerialPortSettingsEntry

monitorBaudRate		1.3.6.1.4.1.8691.2.13.1.6.4.1.1.1
View the current baudrate of the port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

monitorDataBits		1.3.6.1.4.1.8691.2.13.1.6.4.1.1.2
View the number of bits per byte for the port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	bits-5(5), bits-6(6), bits-7(7), bits-8(8)

monitorStopBits		1.3.6.1.4.1.8691.2.13.1.6.4.1.1.3
View the number of stop bits for the port.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

monitorParity		1.3.6.1.4.1.8691.2.13.1.6.4.1.1.4
View the parity bit for the port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(0), odd(8), even(24), mark(40), space(56)

monitorRTSCTSFlowControl		1.3.6.1.4.1.8691.2.13.1.6.4.1.1.5
View if the port is using RTS/CTS flow control.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

monitorXONXOFFFlowControl		1.3.6.1.4.1.8691.2.13.1.6.4.1.1.6
View if the port is using XON/XOFF flow control.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	off(0), on(1)

monitorFIFO		1.3.6.1.4.1.8691.2.13.1.6.4.1.1.7
View FIFO status of this port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	disable(0), enable(1)

monitorInterface		1.3.6.1.4.1.8691.2.13.1.6.4.1.1.8
View the serial interface that the port is using.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	rs-232(0), rs-422(1), rs-485-2-wire(2), rs-485-4-wire(3)

serialPortBuffering		1.3.6.1.4.1.8691.2.13.1.6.5
OBJECT IDENTIFIER

monitorSerialPortBufferingTable		1.3.6.1.4.1.8691.2.13.1.6.5.1
Serial Port Buffering table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MonitorSerialPortBufferingEntry

monitorSerialPortBufferingEntry		1.3.6.1.4.1.8691.2.13.1.6.5.1.1
Serial Port Settings entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	MonitorSerialPortBufferingEntry

monitorBuffering		1.3.6.1.4.1.8691.2.13.1.6.5.1.1.1
View length of buffered data for the port. The length unit is byte.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

sysWlanStatus		1.3.6.1.4.1.8691.2.13.1.6.6
OBJECT IDENTIFIER

wlanStatusActiveProfileName		1.3.6.1.4.1.8691.2.13.1.6.6.1
The active profile name.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

wlanStatusIpConfiguration		1.3.6.1.4.1.8691.2.13.1.6.6.2
The IP configuration mode of the NPort. You can choose from four possible IP configuration modes: Static, DHCP, DHCP/BOOTP, BOOTP.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	static(0), dhcp(1), bootp(2)

wlanStatusIpAddress		1.3.6.1.4.1.8691.2.13.1.6.6.3
An IP address is a number assigned to a network device (such as a computer) as a permanent address on the network. Computers use the IP address to identify and talk to each other over the network. Choose a proper IP address that is unique and valid in your network environment.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

wlanStatusNetMask		1.3.6.1.4.1.8691.2.13.1.6.6.4
A subnet mask represents all of the network hosts at one geographic location, in one building, or on the same local area network. When a packet is sent out over the network, the NPort W2x50A series device server will use the subnet mask to check whether the TCP/IP host specified in the packet is on the local network segment. If the address is on the same network segment as the NPort W2x50A series device server, a connection is established directly from the NPort W2x50A series device server. Otherwise, the connection is established through the given default gateway.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

wlanStatusDefaultGateway		1.3.6.1.4.1.8691.2.13.1.6.6.5
A gateway is a network computer that acts as an entrance to another network. Usually, the computers that control traffic within the network or at the local Internet service provider are gateway nodes. The NPort W2x50A series device server needs to know the IP address of the default gateway computer in order to communicate with the hosts outside the local network environment. For correct gateway IP address information, consult with the network administrator.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

wlanStatusNetworkType		1.3.6.1.4.1.8691.2.13.1.6.6.6
Network Type of Wireless LAN. The possible values are 'Infrastrcture Mode' and 'Ad-hoc Mode'
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

wlanStatusRFType		1.3.6.1.4.1.8691.2.13.1.6.6.7
RF type of Wireless LAN. The possible values are 'N/A', 'Auto', '802.11a', '802.11b', '802.11g'
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

wlanStatusSSID		1.3.6.1.4.1.8691.2.13.1.6.6.8
The SSID of WLAN.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

wlanStatusChannel		1.3.6.1.4.1.8691.2.13.1.6.6.9
The currently used channel.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

wlanStatusAuthentication		1.3.6.1.4.1.8691.2.13.1.6.6.10
Authentication type of Wireless LAN. The possible values are 'Unknown', 'Open System', 'Shared Key', 'WPA', 'WPA-PSK', 'WPA2', 'WPA2-PSK'
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

wlanStatusEncryption		1.3.6.1.4.1.8691.2.13.1.6.6.11
Show encryption type of Wireless LAN.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

wlanStatusRegion		1.3.6.1.4.1.8691.2.13.1.6.6.12
Display region. The possible values are 'US', 'EU', 'JP'
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

wlanStatusSignalStrength		1.3.6.1.4.1.8691.2.13.1.6.6.13
The signal strength of Wireless LAN.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

wlanStatusConnectionSpeed		1.3.6.1.4.1.8691.2.13.1.6.6.14
The connection speed of Wireless LAN.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

wlanStatusCurrentBSSID		1.3.6.1.4.1.8691.2.13.1.6.6.15
The current BSSID of Wireless LAN.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

activateSettings		1.3.6.1.4.1.8691.2.13.1.7
OBJECT IDENTIFIER

doActivate		1.3.6.1.4.1.8691.2.13.1.7.1
Activate current settings.
Status: current	Access: write-only
OBJECT-TYPE
	INTEGER	activate(1)

restart		1.3.6.1.4.1.8691.2.13.1.8
OBJECT IDENTIFIER

restartPorts		1.3.6.1.4.1.8691.2.13.1.8.1
Restart serial port. Restarting will cause port reseting.
Status: current	Access: write-only
OBJECT-TYPE
	INTEGER	port1(0), port2(1)

restartSystem		1.3.6.1.4.1.8691.2.13.1.8.2
Restart the NPort W2x50A series device server. Be sure to save all of your configuration changes before you restart the system. Otherwise, all of the changes will be lost.
Status: current	Access: write-only
OBJECT-TYPE
	INTEGER	restart(1)

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor