LINK-PROBE-MIB

File: LINK-PROBE-MIB.mib (163961 bytes)

Imported modules

RFC1155-SMI RFC1213-MIB RFC-1212
RFC-1215

Imported symbols

Counter IpAddress enterprises
Gauge DisplayString OBJECT-TYPE
sysName TRAP-TYPE

Defined Types

PVC-Entry  
SEQUENCE    
  pvc-Table-Index INTEGER
  pvc-Operation INTEGER
  pvc-Remote-IpAddress IpAddress

PvcCirEir-Entry  
SEQUENCE    
  pvcCirEir-Table-Index INTEGER
  pvcCirToDTE INTEGER
  pvcCirToDCE INTEGER
  pvcEirToDTE INTEGER
  pvcEirToDCE INTEGER

ChStInterval-Entry  
SEQUENCE    
  chStIntv-index INTEGER
  dte-frames-ch-intv Counter
  dce-frames-ch-intv Counter
  dte-octets-ch-intv Counter
  dce-octets-ch-intv Counter
  lmi-enq-tx-ch-intv Counter
  lmi-resp-tx-ch-intv Counter
  lmi-enq-rx-ch-intv Counter
  lmi-resp-rx-ch-intv Counter
  fecn-frames-ch-intv Counter
  becn-frames-ch-intv Counter
  ip-tx-ch-intv Counter
  ip-rx-ch-intv Counter
  poll-tx-ch-intv Counter
  resp-tx-ch-intv Counter
  poll-rx-ch-intv Counter
  resp-rx-ch-intv Counter

PVCStCurrent-entry  
SEQUENCE    
  pvc-number-index-curr INTEGER
  dte-frames-pvc-curr Counter
  dce-frames-pvc-curr Counter
  dte-octets-pvc-curr Counter
  dce-octets-pvc-curr Counter
  dte-frames-with-DE-pvc-curr Counter
  dce-frames-with-DE-pvc-curr Counter
  fecn-frames-pvc-curr Counter
  becn-frames-pvc-curr Counter
  poll-tx-pvc-curr Counter
  resp-tx-pvc-curr Counter
  poll-rx-pvc-curr Counter
  resp-rx-pvc-curr Counter
  pvc-loop-curr INTEGER
  ip-poll-tx-pvc-curr Counter
  ip-resp-tx-pvc-curr Counter
  ip-poll-rx-pvc-curr Counter
  ip-resp-rx-pvc-curr Counter
  ipRtrRxLatTxPvcCurr Counter
  ipRtrRxLatRxPvcCurr Counter
  ipRtrTxLatTxPvcCurr Counter
  ipRtrTxLatRxPvcCurr Counter

PVCStInterval-entry  
SEQUENCE    
  pvc-number-index-intv INTEGER
  pvcStIntv-index INTEGER
  dte-frames-pvc-intv Counter
  dce-frames-pvc-intv Counter
  dte-octets-pvc-intv Counter
  dce-octets-pvc-intv Counter
  dte-frames-with-DE-pvc-intv Counter
  dce-frames-with-DE-pvc-intv Counter
  fecn-frames-pvc-intv Counter
  becn-frames-pvc-intv Counter
  poll-tx-pvc-intv Counter
  resp-tx-pvc-intv Counter
  poll-rx-pvc-intv Counter
  resp-rx-pvc-intv Counter
  pvc-loop-intv INTEGER
  ip-poll-tx-pvc-intv Counter
  ip-resp-tx-pvc-intv Counter
  ip-poll-rx-pvc-intv Counter
  ip-resp-rx-pvc-intv Counter
  ipRtrRxLatTxPvcIntv Counter
  ipRtrRxLatRxPvcIntv Counter
  ipRtrTxLatTxPvcIntv Counter
  ipRtrTxLatRxPvcIntv Counter

ChanPerfIntv-Entry  
SEQUENCE    
  chanPerfIntv-index INTEGER
  chan-unavail-toDte-intv DisplayString
  chan-unavail-toDce-intv DisplayString
  chan-user-load-tx-intv DisplayString
  chan-user-load-rx-intv DisplayString
  chan-total-load-tx-intv DisplayString
  chan-total-load-rx-intv DisplayString
  chan-min-user-load-tx-intv DisplayString
  chan-min-user-load-tx-time-intv DisplayString
  chan-min-user-load-rx-intv DisplayString
  chan-min-user-load-rx-time-intv DisplayString
  chan-min-total-load-tx-intv DisplayString
  chan-min-total-load-tx-time-intv DisplayString
  chan-min-total-load-rx-intv DisplayString
  chan-min-total-load-rx-time-intv DisplayString
  chan-max-user-load-tx-intv DisplayString
  chan-max-user-load-tx-time-intv DisplayString
  chan-max-user-load-rx-intv DisplayString
  chan-max-user-load-rx-time-intv DisplayString
  chan-max-total-load-tx-intv DisplayString
  chan-max-total-load-tx-time-intv DisplayString
  chan-max-total-load-rx-intv DisplayString
  chan-max-total-load-rx-time-intv DisplayString

PvcPerfCurr-Entry  
SEQUENCE    
  pvcPerfCurr-num-index INTEGER
  pvc-tx-time-curr INTEGER
  pvc-unavail-toDte DisplayString
  pvc-unavail-toDce DisplayString
  pvc-user-load-tx-curr DisplayString
  pvc-user-load-rx-curr DisplayString
  pvc-total-load-tx-curr DisplayString
  pvc-total-load-rx-curr DisplayString
  pvc-CIR-toNet-exceed-curr INTEGER
  pvc-EIR-toNet-exceed-curr INTEGER
  pvc-loss-frame-tx-curr INTEGER
  pvc-loss-frame-rx-curr INTEGER
  pvc-ip-tx-time-curr INTEGER
  pvcIpRtrRxLatTxTimeCurr INTEGER
  pvcIpRtrTxLatTxTimeCurr INTEGER

PvcPerfIntv-Entry  
SEQUENCE    
  pvcPerfIntv-num-index INTEGER
  pvcPerf-intv-index INTEGER
  pvc-tx-time-intv INTEGER
  pvc-unavail-toDte-intv DisplayString
  pvc-unavail-toDce-intv DisplayString
  pvc-user-load-tx-intv DisplayString
  pvc-user-load-rx-intv DisplayString
  pvc-total-load-tx-intv DisplayString
  pvc-total-load-rx-intv DisplayString
  pvc-CIR-toNet-exceed-intv INTEGER
  pvc-EIR-toNet-exceed-intv INTEGER
  pvc-loss-frame-tx-intv INTEGER
  pvc-loss-frame-rx-intv INTEGER
  pvc-ip-tx-time-intv INTEGER
  pvcIpRtrRxLatTxTimeIntv INTEGER
  pvcIpRtrTxLatTxTimeIntv INTEGER
  pvc-min-tx-time-intv INTEGER
  pvc-min-tx-time-time-intv DisplayString
  pvc-min-user-load-tx-intv DisplayString
  pvc-min-user-load-tx-time-intv DisplayString
  pvc-min-user-load-rx-intv DisplayString
  pvc-min-user-load-rx-time-intv DisplayString
  pvc-min-total-load-tx-intv DisplayString
  pvc-min-total-load-tx-time-intv DisplayString
  pvc-min-total-load-rx-intv DisplayString
  pvc-min-total-load-rx-time-intv DisplayString
  pvc-min-ip-tx-time-intv INTEGER
  pvc-min-ip-tx-time-time-intv DisplayString
  pvc-max-tx-time-intv INTEGER
  pvc-max-tx-time-time-intv DisplayString
  pvc-max-user-load-tx-intv DisplayString
  pvc-max-user-load-tx-time-intv DisplayString
  pvc-max-user-load-rx-intv DisplayString
  pvc-max-user-load-rx-time-intv DisplayString
  pvc-max-total-load-tx-intv DisplayString
  pvc-max-total-load-tx-time-intv DisplayString
  pvc-max-total-load-rx-intv DisplayString
  pvc-max-total-load-rx-time-intv DisplayString
  pvc-max-ip-tx-time-intv INTEGER
  pvc-max-ip-tx-time-time-intv DisplayString

PvcShapeCurrToDce-Entry  
SEQUENCE    
  pvcShapeCurrToDce-index INTEGER
  pvcShapeCurrToDceLevel-1 INTEGER
  pvcShapeCurrToDceLevel-2 INTEGER
  pvcShapeCurrToDceLevel-3 INTEGER
  pvcShapeCurrToDceLevel-4 INTEGER
  pvcShapeCurrToDceLevel-5 INTEGER
  pvcShapeCurrToDceLevel-6 INTEGER
  pvcShapeCurrToDceLevel-7 INTEGER

PvcShapeCurrToDte-Entry  
SEQUENCE    
  pvcShapeCurrToDte-index INTEGER
  pvcShapeCurrToDteLevel-1 INTEGER
  pvcShapeCurrToDteLevel-2 INTEGER
  pvcShapeCurrToDteLevel-3 INTEGER
  pvcShapeCurrToDteLevel-4 INTEGER
  pvcShapeCurrToDteLevel-5 INTEGER
  pvcShapeCurrToDteLevel-6 INTEGER
  pvcShapeCurrToDteLevel-7 INTEGER

PvcShapeIntvToDce-Entry  
SEQUENCE    
  pvcShapeIntvToDce-pvcIx INTEGER
  pvcShapeIntvToDce-intvIx INTEGER
  pvcShapeIntvToDceLevel-1 INTEGER
  pvcShapeIntvToDceLevel-2 INTEGER
  pvcShapeIntvToDceLevel-3 INTEGER
  pvcShapeIntvToDceLevel-4 INTEGER
  pvcShapeIntvToDceLevel-5 INTEGER
  pvcShapeIntvToDceLevel-6 INTEGER
  pvcShapeIntvToDceLevel-7 INTEGER

PvcShapeIntvToDte-Entry  
SEQUENCE    
  pvcShapeIntvToDte-pvcIx INTEGER
  pvcShapeIntvToDte-intvIx INTEGER
  pvcShapeIntvToDteLevel-1 INTEGER
  pvcShapeIntvToDteLevel-2 INTEGER
  pvcShapeIntvToDteLevel-3 INTEGER
  pvcShapeIntvToDteLevel-4 INTEGER
  pvcShapeIntvToDteLevel-5 INTEGER
  pvcShapeIntvToDteLevel-6 INTEGER
  pvcShapeIntvToDteLevel-7 INTEGER

HistIntvStartTimeIntv-Entry  
SEQUENCE    
  histIntvStartTimeIntv-index INTEGER
  hist-intv-start-time DisplayString

HistChanPerfIntv-Entry  
SEQUENCE    
  histChanPerfIntv-index INTEGER
  hist-chan-unavail-toDte-intv DisplayString
  hist-chan-unavail-toDce-intv DisplayString
  hist-chan-user-load-tx-intv DisplayString
  hist-chan-user-load-rx-intv DisplayString

HistPvcPerfIntv-Entry  
SEQUENCE    
  histPvcPerfIntv-num-index INTEGER
  histPvcPerf-intv-index INTEGER
  hist-pvc-tx-time-intv INTEGER
  hist-pvc-unavail-toDte-intv DisplayString
  hist-pvc-unavail-toDce-intv DisplayString
  hist-pvc-user-load-tx-intv DisplayString
  hist-pvc-user-load-rx-intv DisplayString
  hist-pvc-CIR-toNet-exceed-intv INTEGER
  hist-pvc-loss-frame-tx-intv INTEGER
  hist-pvc-loss-frame-rx-intv INTEGER

HistPvcShapeIntvToDce-Entry  
SEQUENCE    
  histPvcShapeIntvToDce-pvcIx INTEGER
  histPvcShapeIntvToDce-intvIx INTEGER
  histPvcShapeIntvToDceLevel-1 INTEGER
  histPvcShapeIntvToDceLevel-2 INTEGER
  histPvcShapeIntvToDceLevel-3 INTEGER
  histPvcShapeIntvToDceLevel-4 INTEGER
  histPvcShapeIntvToDceLevel-5 INTEGER
  histPvcShapeIntvToDceLevel-6 INTEGER
  histPvcShapeIntvToDceLevel-7 INTEGER

HistPvcShapeIntvToDte-Entry  
SEQUENCE    
  histPvcShapeIntvToDte-pvcIx INTEGER
  histPvcShapeIntvToDte-intvIx INTEGER
  histPvcShapeIntvToDteLevel-1 INTEGER
  histPvcShapeIntvToDteLevel-2 INTEGER
  histPvcShapeIntvToDteLevel-3 INTEGER
  histPvcShapeIntvToDteLevel-4 INTEGER
  histPvcShapeIntvToDteLevel-5 INTEGER
  histPvcShapeIntvToDteLevel-6 INTEGER
  histPvcShapeIntvToDteLevel-7 INTEGER

IntvStartTimeIntv-Entry  
SEQUENCE    
  intvStartTimeIntv-index INTEGER
  intv-start-time DisplayString

DbuPVCEntry  
SEQUENCE    
  dbuPVCTableIndex INTEGER
  dbuRemotePVCDlci INTEGER
  dbuIsdnAddress DisplayString
  dbuPvcCir INTEGER

PvcStatusEntry  
SEQUENCE    
  pvcStatusIndex INTEGER
  pvcStatus INTEGER

Defined Values

netQuest 1.3.6.1.4.1.568
OBJECT IDENTIFIER    


probeConfig 1.3.6.1.4.1.568.8.1
OBJECT IDENTIFIER    

probeStat 1.3.6.1.4.1.568.8.2
OBJECT IDENTIFIER    

probePerform 1.3.6.1.4.1.568.8.3
OBJECT IDENTIFIER    

probeTrafficShape 1.3.6.1.4.1.568.8.4
OBJECT IDENTIFIER    

probeHistorical 1.3.6.1.4.1.568.8.5
OBJECT IDENTIFIER    

probeIntervalStartTime 1.3.6.1.4.1.568.8.6
OBJECT IDENTIFIER    

dbuConfigGroup 1.3.6.1.4.1.568.8.7
OBJECT IDENTIFIER    

deviceStatusGroup 1.3.6.1.4.1.568.8.8
OBJECT IDENTIFIER    

trapAcknowledgeGroup 1.3.6.1.4.1.568.8.9
OBJECT IDENTIFIER    

chan-config 1.3.6.1.4.1.568.8.1.1
OBJECT IDENTIFIER    

lmi-config 1.3.6.1.4.1.568.8.1.2
OBJECT IDENTIFIER    

pro-fun-config 1.3.6.1.4.1.568.8.1.3
OBJECT IDENTIFIER    

trap-config 1.3.6.1.4.1.568.8.1.4
OBJECT IDENTIFIER    

pvc-config 1.3.6.1.4.1.568.8.1.5
OBJECT IDENTIFIER    

file-download-config 1.3.6.1.4.1.568.8.1.6
OBJECT IDENTIFIER    

net-management-config 1.3.6.1.4.1.568.8.1.7
OBJECT IDENTIFIER    

lmi-Operation 1.3.6.1.4.1.568.8.1.1.1
LMI operation, on -- enabled, off -- disabled
OBJECT-TYPE    
  INTEGER off(1), on(2)  

lmi-DLCI 1.3.6.1.4.1.568.8.1.1.2
LMI DLCI can just take two values: DLCI 0 or DLCI 1023, default is 0.
OBJECT-TYPE    
  INTEGER pvc-0(1), pvc-1023(2)  

inband-IP-DLCI 1.3.6.1.4.1.568.8.1.1.3
valid Inband IP DLCI ranges from 16 to 991, read only object
OBJECT-TYPE    
  INTEGER 16..991  

ip-Encapsu 1.3.6.1.4.1.568.8.1.1.4
Indicate which IP DLCI Encapsulation method
OBJECT-TYPE    
  INTEGER raw-ip(1), ietf-ip(2), snap-ip(3)  

interface-Speed 1.3.6.1.4.1.568.8.1.1.5
Interface Speed is n*8 kpbs, the default value is 64 kbps.
OBJECT-TYPE    
  INTEGER n64-kbps(1), n128-kbps(2), n192-kbps(3), n256-kbps(4), n320-kbps(5), n384-kbps(6), n448-kbps(7), n512-kbps(8), n576-kbps(9), n640-kbps(10), n704-kbps(11), n768-kbps(12), n832-kbps(13), n896-kbps(14), n960-kbps(15), n1024-kbps(16), n1088-kbps(17), n1152-kbps(18), n1216-kbps(19), n1280-kbps(20), n1344-kbps(21), n1408-kbps(22), n1472-kbps(23), n1536-kbps(24), n1600-kbps(25), n1664-kbps(26), n1728-kbps(27), n1792-kbps(28), n1856-kbps(29), n1920-kbps(30), n1984-kbps(31), n2048-kbps(32)  

nvram-update 1.3.6.1.4.1.568.8.1.1.6
This object lets the user decide if he (she) wants to write the just modified parameters in channel configuration group to nvram, if he chose 'write', these parameters will be updated; and if he chose 'restore', the modifications are lost.
OBJECT-TYPE    
  INTEGER write-to-nvram(1), restoreParam(2)  

lmi-type 1.3.6.1.4.1.568.8.1.2.1
This object identifies the LMI type the network is currently using, read/write object.
OBJECT-TYPE    
  INTEGER annex-a(1), annex-d(2), lmi-rev1(3)  

max-Info-Length 1.3.6.1.4.1.568.8.1.2.2
Maximum supported frame information length ranges from 400 to 4000, the default value is 4000.
OBJECT-TYPE    
  INTEGER 400..4000  

n391-Counter 1.3.6.1.4.1.568.8.1.2.3
N391 Counter ranges from 1 to 255, the default value is 6.
OBJECT-TYPE    
  INTEGER 1..255  

n392-Net-Counter 1.3.6.1.4.1.568.8.1.2.4
N392 Net Counter ranges from 1 to 10, the default value is 3.
OBJECT-TYPE    
  INTEGER 1..10  

n392-User-Counter 1.3.6.1.4.1.568.8.1.2.5
N392 User Counter ranges from 1 to 10, the default value is 3.
OBJECT-TYPE    
  INTEGER 1..10  

n393-Net-Counter 1.3.6.1.4.1.568.8.1.2.6
N393 Net Counter ranges from 1 to 10, the default value is 4.
OBJECT-TYPE    
  INTEGER 1..10  

n393-User-Counter 1.3.6.1.4.1.568.8.1.2.7
N393 User Counter ranges from 1 to 10, the default value is 4.
OBJECT-TYPE    
  INTEGER 1..10  

t391-Timer 1.3.6.1.4.1.568.8.1.2.8
T391 Timer ranges from 5 to 30, the default value is 10, which would always less than or equal to T392 Timer.
OBJECT-TYPE    
  INTEGER 5..30  

t392-Timer 1.3.6.1.4.1.568.8.1.2.9
T392 Timer ranges from 5 to 30, the default value is 15. which should always greater than T391 Timer.
OBJECT-TYPE    
  INTEGER 5..30  

lMI-Controller 1.3.6.1.4.1.568.8.1.2.10
This object lets the user decide if he (she) wants to update the just modified LMI parameters, only when the user chooses to update will the new parameters be accepted by the system. If the user selects the restoreParam value then the LMI parameters will revert to the previous values, and the modifications are lost.
OBJECT-TYPE    
  INTEGER update-para(1), restoreParam(2)  

softwareVersion 1.3.6.1.4.1.568.8.1.3.1
This object displays the software version we are currently running, so according to the version number, the user can determine which version is newer.
OBJECT-TYPE    
  DisplayString Size(0..10)  

probe-Mode 1.3.6.1.4.1.568.8.1.3.2
Probe mode defines whether the link probe is generator, responder, both or disabled.
OBJECT-TYPE    
  INTEGER generator(1), responder(2), both(3), disabled(4)  

poll-Period 1.3.6.1.4.1.568.8.1.3.3
poll period defines the frequency of sending the polling frame by the link probe. The value is between 1 to 60 sec. The poll period applies to all PVCs that are to be probed.
OBJECT-TYPE    
  INTEGER 1..60  

sys-current-time 1.3.6.1.4.1.568.8.1.3.4
sys-current-time displays the system current time with 4 digits year, 2 digits month, 2 digits date and hours, minutes and seconds, which are each 2 digits. If the user wants to set the current time, he (she) must follow the correct formats.
OBJECT-TYPE    
  DisplayString Size(0..255)  

current-intv-start-time 1.3.6.1.4.1.568.8.1.3.5
current-intv-start-time displays the current interval starting time with 4 digits year, 2 digits month, 2 digits date and hours, minutes and seconds, which are each 2 digits.
OBJECT-TYPE    
  DisplayString Size(0..255)  

pvc-Count 1.3.6.1.4.1.568.8.1.3.6
PVC count defines the total number of PVCs which are to be probed. The value is between 1 to 20.
OBJECT-TYPE    
  INTEGER 1..20  

probeTokenSize 1.3.6.1.4.1.568.8.1.3.7
This object defines the probe token size.
OBJECT-TYPE    
  INTEGER 19..4096  

pvc-add 1.3.6.1.4.1.568.8.1.3.8
This object allows the user to add a PVC to the existing PVC table, the added PVC must not exist before it is added.
OBJECT-TYPE    
  INTEGER 16..991  

pvc-delete 1.3.6.1.4.1.568.8.1.3.9
This object allows the user to delete a PVC from the existing PVC table, the deleted PVC must exist before it was deleted.
OBJECT-TYPE    
  INTEGER 16..991  

pvc-Table 1.3.6.1.4.1.568.8.1.3.10
PVC table, which lists PVCs that currently are probed.
OBJECT-TYPE    
  SEQUENCE OF  
    PVC-Entry

pvc-Entry 1.3.6.1.4.1.568.8.1.3.10.1
Identifies an entry (row) in PVC table.
OBJECT-TYPE    
  PVC-Entry  

pvc-Table-Index 1.3.6.1.4.1.568.8.1.3.10.1.1
Identifies an entry (row) in PVC table.
OBJECT-TYPE    
  INTEGER 16..991  

pvc-Operation 1.3.6.1.4.1.568.8.1.3.10.1.2
This object identifies the three possible states which a pvc can be in, '1' means we are just collecting the statistical data for this PVC, '2' means we are not just collecting statistic data for this PVC, but also put it into a pending table waiting for probe, '3' means this PVC is used for both collecting statistic data and probing. Even though we can view three states for this PVC, we can just set '1' or '2' for this PVC.
OBJECT-TYPE    
  INTEGER pvc-not-probed(1), pvc-in-waiting(2), pvc-probed(3)  

pvc-Remote-IpAddress 1.3.6.1.4.1.568.8.1.3.10.1.3
This object defines the IP address of the remote probe used with IP monitoring.
OBJECT-TYPE    
  IpAddress  

alternateVersion 1.3.6.1.4.1.568.8.1.3.11
This object displays the software version we are not currently running, so according to the version number, the user can determine which version is newer.
OBJECT-TYPE    
  DisplayString Size(0..10)  

bypassStatus 1.3.6.1.4.1.568.8.1.3.12
This object identifies the three possible states which data bypass can be in. '1' means frame relay data bypass is off. '2' means frame relay data bypass is on. '3' means frame relay data bypass is on and was set on automatically because there was no DCD and no RTS. State '1' can only be set if state is '2'. State '2' can only be set if state is '1'. State '3' cannot be set manually.
OBJECT-TYPE    
  INTEGER bypass-off(1), bypass-on(2), bypass-auto(3)  

trapCtlGlobal 1.3.6.1.4.1.568.8.1.4.1
This object is used to enable or disable system traps. Only when it is enabled, the standard traps, such as cold start trap, warm start trap; and enterprise specific traps can be sent.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

trapCtlSpecific 1.3.6.1.4.1.568.8.1.4.2
This parameter is a bitmap for the 16 enterprise specific traps, zero means all the traps are disabled and 0xffff means all the traps are enabled. The following lists the 16 bits which are defined: 1st bit = pvcNotAvailDCE-trap; 2nd bit = pvcNotAvailDTE-trap; 3rd bit = pvcAveRTD-trap; 4th bit = frChanUtilizeToDTE-trap; 5th bit = frChanUtilizeToDCE-trap; 6th bit = pvcBecn-trap; 7th bit = pvcFecn-trap; 8th bit = pvcUtilToDTE-trap; 9th bit = pvcUtilToDCE-trap; 10th bit = pvcCIRExceed-trap; 11th bit = pvcEIRExceed-trap; 12th bit = pvcLossFrameTx-trap; 13th bit = pvcLossFrameRx-trap; 14th bit = all real-time exception and endOfException traps; 15th bit = pvcStatusChange; 16th bit = dbuTrapsEnable;
OBJECT-TYPE    
  INTEGER 0..65535  

pvcNotAvailThreshDCE 1.3.6.1.4.1.568.8.1.4.3
This parameter defines the allowed maximum PVC not availability threshold within current time interval due to a network fault. It is expressed as a percentage of full interval time. If the actual average value is more than this threshold, a trap will be sent at the end of the interval.
OBJECT-TYPE    
  INTEGER 0..100  

pvcNotAvailThreshDTE 1.3.6.1.4.1.568.8.1.4.4
This parameter defines the allowed maximum PVC not availability threshold within current time interval due to the local DTE fault. It is expressed as a percentage of full interval time. If the actual average value is more than this threshold, a trap will be sent at the end of the interval.
OBJECT-TYPE    
  INTEGER 0..100  

pvcAveRTDThresh 1.3.6.1.4.1.568.8.1.4.5
This parameter defines the allowed maximum PVC round trip time delay (milliseconds) within the current time interval. If the actual average round trip delay is more than this threshold, a trap will be sent at the end of the interval.
OBJECT-TYPE    
  INTEGER 0..500  

frChanUtilizThreshToDTE 1.3.6.1.4.1.568.8.1.4.6
This parameter defines the maximum allowed frame relay channel utilization to the DTE direction. It is expressed in percentage. If the actual average utilization is more than this threshold, a trap will be sent at the end of the interval.
OBJECT-TYPE    
  INTEGER 0..2048  

frChanUtilizThreshToDCE 1.3.6.1.4.1.568.8.1.4.7
This parameter defines the maximum allowed frame relay channel utilization to the DCE direction. It is expressed in percentage. If the actual average utilization is more than this threshold, a trap will be sent at the end of the interval.
OBJECT-TYPE    
  INTEGER 0..2048  

pvcBecnThresh 1.3.6.1.4.1.568.8.1.4.8
This parameter defines the maximum allowed BECNs for a PVC within current interval. If the actual BECNs are more than this threshold, a trap will be sent at the end of the interval.
OBJECT-TYPE    
  INTEGER 0..2048  

pvcFecnThresh 1.3.6.1.4.1.568.8.1.4.9
This parameter defines the maximum allowed FECNs for a PVC within current interval. If the actual FECNs are more than this threshold, a trap will be sent at the end of the interval.
OBJECT-TYPE    
  INTEGER 0..2048  

pvcUtilToDTEThresh 1.3.6.1.4.1.568.8.1.4.10
This parameter defines the maximum allowed PVC utilization to DTE within current interval. If the actual average utilization is more than this threshold, a trap will be sent at the end of the interval.
OBJECT-TYPE    
  INTEGER 0..2048  

pvcUtilToDCEThresh 1.3.6.1.4.1.568.8.1.4.11
This parameter defines the maximum allowed PVC utilization to DCE within current interval. If the actual average utilization is more than this threshold, a trap will be sent at the end of the interval.
OBJECT-TYPE    
  INTEGER 0..2048  

chanLoadToDTEThresh-realTime 1.3.6.1.4.1.568.8.1.4.12
This parameter defines the maximum allowed real-time channel load to the DTE direction (calculated within every TC). It is expressed in percentage. If the actual load is more than this threshold, an exception trap will be sent immediately.
OBJECT-TYPE    
  INTEGER 0..2048  

chanLoadToDCEThresh-realTime 1.3.6.1.4.1.568.8.1.4.13
This parameter defines the maximum allowed real-time channel load to the DCE direction (calculated within every TC). It is expressed in percentage. If the actual load is more than this, threshold, an exception trap will be sent immediately.
OBJECT-TYPE    
  INTEGER 0..2048  

chanLoadThreshToDTE-realTimeRange 1.3.6.1.4.1.568.8.1.4.14
This parameter defines the variation range for real-time channel load to the DTE exception trap. If within the current TC interval, the variation of the actual utilization is more than that range compared with previous trap value, another exception trap will be sent immediately. This variation range is defined in percentage.
OBJECT-TYPE    
  INTEGER 0..100  

chanLoadThreshToDCE-realTimeRange 1.3.6.1.4.1.568.8.1.4.15
This parameter defines the variation range for real-time channel load to the DCE exception trap. If within the current TC interval, the variation of the actual utilization is more than that range compared with previous trap value, another exception trap will be sent immediately. This variation range is defined in percentage.
OBJECT-TYPE    
  INTEGER 0..100  

pvcRTDThresh-realTime 1.3.6.1.4.1.568.8.1.4.16
This parameter defines the maximum allowed real-time PVC Round Trip Delay in msec., it is calculated as the same frequency as the Probe Polls (1 to 60 sec.). If the actual RTD is more than this threshold, an exception trap will be sent immediately.
OBJECT-TYPE    
  INTEGER 0..2048  

pvcRTDThresh-realTimeRange 1.3.6.1.4.1.568.8.1.4.17
This parameter defines the variation range for real-time PVC RTD exception trap. If the variation of the current RTD value is more than this range compared with previous trap value, another exception trap or endOfException will be sent immediately. This variation range is defined in percentage.
OBJECT-TYPE    
  INTEGER 0..100  

pvcLoadToDTEThresh-realTime 1.3.6.1.4.1.568.8.1.4.18
This parameter defines the maximum allowed real-time PVC load to the DTE direction (calculated within every TC). It is expressed in percentage. If the actual load is more than this threshold, an exception trap will be sent immediately.
OBJECT-TYPE    
  INTEGER 0..2048  

pvcLoadToDCEThresh-realTime 1.3.6.1.4.1.568.8.1.4.19
This parameter defines the maximum allowed real-time PVC load to the DCE direction (calculated within every TC). It is expressed in percentage. If the actual load is more than this threshold, an exception trap will be sent immediately.
OBJECT-TYPE    
  INTEGER 0..2048  

pvcLoadToDTEThresh-realTimeRange 1.3.6.1.4.1.568.8.1.4.20
This parameter defines the variation range for real-time PVC load to the DTE exception trap. If within the current TC interval, the variation of the actual utilization is more than that range compared with previous trap value, another exception trap will be sent immediately. This variation range is defined in percentage.
OBJECT-TYPE    
  INTEGER 0..100  

pvcLoadToDCEThresh-realTimeRange 1.3.6.1.4.1.568.8.1.4.21
This parameter defines the variation range for real-time PVC load to the DCE exception trap. If within the current TC interval, the variation of the actual utilization is more than that range compared with previous trap value, another exception trap will be sent immediately. This variation range is defined in percentage.
OBJECT-TYPE    
  INTEGER 0..100  

pvcTC 1.3.6.1.4.1.568.8.1.5.1
This parameter defines the committed rate measurement time interval (in 1/10 second) which can be calculated as Bc/CIR. For example, if we want TC to be 1 sec., this object should be set as 10.
OBJECT-TYPE    
  INTEGER 0..100  

pvcCirEir-Table 1.3.6.1.4.1.568.8.1.5.2
PVC table, which lists PVCs for which the statistical data are collected.
OBJECT-TYPE    
  SEQUENCE OF  
    PvcCirEir-Entry

pvcCirEir-Entry 1.3.6.1.4.1.568.8.1.5.2.1
Identifies an entry (row) in PVC CIR/EIR table.
OBJECT-TYPE    
  PvcCirEir-Entry  

pvcCirEir-Table-Index 1.3.6.1.4.1.568.8.1.5.2.1.1
Identifies an entry (row) in PVC table.
OBJECT-TYPE    
  INTEGER 16..991  

pvcCirToDTE 1.3.6.1.4.1.568.8.1.5.2.1.2
This parameter defines the committed information rate (bps) under normal condition in the direction of to DTE.
OBJECT-TYPE    
  INTEGER 1..2048000  

pvcCirToDCE 1.3.6.1.4.1.568.8.1.5.2.1.3
This parameter defines the committed information rate (bps) under normal condition in the direction of to DCE.
OBJECT-TYPE    
  INTEGER 1..2048000  

pvcEirToDTE 1.3.6.1.4.1.568.8.1.5.2.1.4
This parameter defines the maximum transfer information rate (bps) which the network is accepting in the direction of to DTE.
OBJECT-TYPE    
  INTEGER 0..2048000  

pvcEirToDCE 1.3.6.1.4.1.568.8.1.5.2.1.5
This parameter defines the maximum transfer information rate (bps) which the network is accepting in the direction of to DCE.
OBJECT-TYPE    
  INTEGER 0..2048000  

sourceIpAddress 1.3.6.1.4.1.568.8.1.6.1
This object defines the IP address of the place where the updated file would store, currently we use a long integer to display.
OBJECT-TYPE    
  IpAddress  

sourceFileName 1.3.6.1.4.1.568.8.1.6.2
This object defines the name of the updated file.
OBJECT-TYPE    
  DisplayString Size(0..10)  

sourceFileMode 1.3.6.1.4.1.568.8.1.6.3
This object defines the mode of the updated file.
OBJECT-TYPE    
  INTEGER netAscii(1)  

tftpAction 1.3.6.1.4.1.568.8.1.6.4
This object defines the action we will take of TFTP.
OBJECT-TYPE    
  INTEGER getfile(1)  

changeVersion 1.3.6.1.4.1.568.8.1.6.5
This object is related to the next software reset object, the user can change the version of software and reset it. If in the middle of a TFTP transfer, this object cannot be set. It also cannot be set to switchVersion if there is no other version to which to switch. An undefined value of 0 is also sameVersion.
OBJECT-TYPE    
  INTEGER sameVersion(1), switchVersion(2)  

softwareReset 1.3.6.1.4.1.568.8.1.6.6
This object is related to the previous software version object, the user can choose the version of software and reset it. If in the middle of a TFTP transfer, this object can not be set.
OBJECT-TYPE    
  INTEGER reset(1)  

tftpState 1.3.6.1.4.1.568.8.1.6.7
This object defines the current state of the TFTP download.
OBJECT-TYPE    
  INTEGER idle-ok(1), active(2), idle-failed(3)  

ipInterface 1.3.6.1.4.1.568.8.1.7.1
This object defines the type of IP interface currently used in the system. pppIpInterface is an asynchronous ppp interface and isdnIpInterface is a synchronous ppp interface.
OBJECT-TYPE    
  INTEGER pppIpInterface(1), ethernetIpInterface(2), privateInbandIpInterface(3), userInbandIpInterface(4), isdnIpInterface(5)  

inbandIpAddress 1.3.6.1.4.1.568.8.1.7.2
This object defines the IP address of the probe over the inband interface. Even though separate from outbandIpAddress, this address only used when ipInterface is inbandIpInterface.
OBJECT-TYPE    
  IpAddress  

outbandIpAddress 1.3.6.1.4.1.568.8.1.7.3
This object defines the IP address of the probe over the current out of band interface: asynchronous ppp, ethernet, or synchronous ppp over ISDN.
OBJECT-TYPE    
  IpAddress  

routerIpAddress 1.3.6.1.4.1.568.8.1.7.4
This object defines the default gateway or next-hop IP address which is used when no route is found.
OBJECT-TYPE    
  IpAddress  

subnetmaskIpAddress 1.3.6.1.4.1.568.8.1.7.5
This object defines the network Id portion of our inbandIpAddress or outbandIpAddress.
OBJECT-TYPE    
  IpAddress  

chStCurrent 1.3.6.1.4.1.568.8.2.1
OBJECT IDENTIFIER    

dte-frames-ch-curr 1.3.6.1.4.1.568.8.2.1.1
Identifies total frames received from DTE device within current 15 minutes interval.
OBJECT-TYPE    
  Counter  

dce-frames-ch-curr 1.3.6.1.4.1.568.8.2.1.2
Identifies total frames received from DCE device within current 15 minutes interval.
OBJECT-TYPE    
  Counter  

dte-octets-ch-curr 1.3.6.1.4.1.568.8.2.1.3
Identifies total octets received from DTE device within current 15 minutes interval.
OBJECT-TYPE    
  Counter  

dce-octets-ch-curr 1.3.6.1.4.1.568.8.2.1.4
Identifies total octets received from DTE device within current 15 minutes interval.
OBJECT-TYPE    
  Counter  

lmi-enq-tx-ch-curr 1.3.6.1.4.1.568.8.2.1.5
Identifies the total number of LMI enquiries sent to DCE within current 15 minutes interval.
OBJECT-TYPE    
  Counter  

lmi-resp-tx-ch-curr 1.3.6.1.4.1.568.8.2.1.6
Identifies the total number of LMI responses sent to DTE within current 15 minutes interval.
OBJECT-TYPE    
  Counter  

lmi-enq-rx-ch-curr 1.3.6.1.4.1.568.8.2.1.7
Identifies the total number of LMI enquiries from the DTE within current 15 minutes interval.
OBJECT-TYPE    
  Counter  

lmi-resp-rx-ch-curr 1.3.6.1.4.1.568.8.2.1.8
Identifies the total number of LMI status responses received from the DCE within current 15 minutes interval.
OBJECT-TYPE    
  Counter  

fecn-frames-ch-curr 1.3.6.1.4.1.568.8.2.1.9
Identifies total number of frames with FECN set received within current 15 minutes interval.
OBJECT-TYPE    
  Counter  

becn-frames-ch-curr 1.3.6.1.4.1.568.8.2.1.10
Identifies total number of frames with BECN set received within current 15 minutes interval.
OBJECT-TYPE    
  Counter  

ip-tx-ch-curr 1.3.6.1.4.1.568.8.2.1.11
Identifies total number of IP packets sent on inband DLCI within current 15 minutes interval.
OBJECT-TYPE    
  Counter  

ip-rx-ch-curr 1.3.6.1.4.1.568.8.2.1.12
Identifies total number of IP packets received on inband DLCI within current 15 minutes interval.
OBJECT-TYPE    
  Counter  

poll-tx-ch-curr 1.3.6.1.4.1.568.8.2.1.13
Identifies total number of probe polls sent to DCE within current 15 minutes interval.
OBJECT-TYPE    
  Counter  

resp-tx-ch-curr 1.3.6.1.4.1.568.8.2.1.14
Identifies total number of probe responses sent to DCE within current 15 minutes interval.
OBJECT-TYPE    
  Counter  

poll-rx-ch-curr 1.3.6.1.4.1.568.8.2.1.15
Identifies total number of probe polls received from DCE within current 15 minutes interval.
OBJECT-TYPE    
  Counter  

resp-rx-ch-curr 1.3.6.1.4.1.568.8.2.1.16
Identifies total number of probe responses received from DCE within current 15 minutes interval.
OBJECT-TYPE    
  Counter  

chStInterval-Table 1.3.6.1.4.1.568.8.2.2
probe statistic table, row 1 to row 96, which defines the time interval for every 15 minutes.
OBJECT-TYPE    
  SEQUENCE OF  
    ChStInterval-Entry

chStInterval-Entry 1.3.6.1.4.1.568.8.2.2.1
Identifies an entry (row) in probe statistic table.
OBJECT-TYPE    
  ChStInterval-Entry  

chStIntv-index 1.3.6.1.4.1.568.8.2.2.1.1
Identifies an entry (row) in channel statistic table, 1-96 time intervals.
OBJECT-TYPE    
  INTEGER 1..96  

dte-frames-ch-intv 1.3.6.1.4.1.568.8.2.2.1.2
Identifies total frames received from DTE device within a 15 minutes interval.
OBJECT-TYPE    
  Counter  

dce-frames-ch-intv 1.3.6.1.4.1.568.8.2.2.1.3
Identifies total frames received from DCE device within a 15 minutes interval.
OBJECT-TYPE    
  Counter  

dte-octets-ch-intv 1.3.6.1.4.1.568.8.2.2.1.4
Identifies total octets received from DTE device within a 15 minutes interval.
OBJECT-TYPE    
  Counter  

dce-octets-ch-intv 1.3.6.1.4.1.568.8.2.2.1.5
Identifies total octets received from DTE device within a 15 minutes interval.
OBJECT-TYPE    
  Counter  

lmi-enq-tx-ch-intv 1.3.6.1.4.1.568.8.2.2.1.6
Identifies the total number of LMI enquiries sent to DCE within a 15 minutes interval.
OBJECT-TYPE    
  Counter  

lmi-resp-tx-ch-intv 1.3.6.1.4.1.568.8.2.2.1.7
Identifies the total number of LMI responses send to DTE within a 15 minutes interval.
OBJECT-TYPE    
  Counter  

lmi-enq-rx-ch-intv 1.3.6.1.4.1.568.8.2.2.1.8
Identifies the total number of LMI enquiries received within a 15 minutes interval.
OBJECT-TYPE    
  Counter  

lmi-resp-rx-ch-intv 1.3.6.1.4.1.568.8.2.2.1.9
Identifies the total number of LMI status responses received from the DCE within a 15 minutes interval.
OBJECT-TYPE    
  Counter  

fecn-frames-ch-intv 1.3.6.1.4.1.568.8.2.2.1.10
Identifies total number of frames with FECN set received within a 15 minutes interval.
OBJECT-TYPE    
  Counter  

becn-frames-ch-intv 1.3.6.1.4.1.568.8.2.2.1.11
Identifies total number of frames with BECN set received within a 15 minutes interval.
OBJECT-TYPE    
  Counter  

ip-tx-ch-intv 1.3.6.1.4.1.568.8.2.2.1.12
Identifies total number of IP packets sent on inband DLCI within a 15 minutes interval.
OBJECT-TYPE    
  Counter  

ip-rx-ch-intv 1.3.6.1.4.1.568.8.2.2.1.13
Identifies total number of IP packets received on inband DLCI within a 15 minutes interval.
OBJECT-TYPE    
  Counter  

poll-tx-ch-intv 1.3.6.1.4.1.568.8.2.2.1.14
Identifies total number of probe polls sent to DCE within a 15 minutes interval.
OBJECT-TYPE    
  Counter  

resp-tx-ch-intv 1.3.6.1.4.1.568.8.2.2.1.15
Identifies total number of probe response sent to DCE within a 15 minutes interval.
OBJECT-TYPE    
  Counter  

poll-rx-ch-intv 1.3.6.1.4.1.568.8.2.2.1.16
Identifies total number of probe polls received from DCE within a 15 minutes interval.
OBJECT-TYPE    
  Counter  

resp-rx-ch-intv 1.3.6.1.4.1.568.8.2.2.1.17
Identifies total number of probe responses received from DCE within a 15 minutes interval.
OBJECT-TYPE    
  Counter  

pvcStCurrent-Table 1.3.6.1.4.1.568.8.2.3
PVC statistic table.
OBJECT-TYPE    
  SEQUENCE OF  
    PVCStCurrent-entry

pvcStCurrent-Entry 1.3.6.1.4.1.568.8.2.3.1
Identifies an entry (row) in PVC statistic table
OBJECT-TYPE    
  PVCStCurrent-entry  

pvc-number-index-curr 1.3.6.1.4.1.568.8.2.3.1.1
Index in PVC statistics table, which identifies the PVC number, up to 20 PVCs can exist.
OBJECT-TYPE    
  INTEGER 16..991  

dte-frames-pvc-curr 1.3.6.1.4.1.568.8.2.3.1.2
Identifies total frames received from DTE device for a specific PVC within current 15 minutes interval.
OBJECT-TYPE    
  Counter  

dce-frames-pvc-curr 1.3.6.1.4.1.568.8.2.3.1.3
Identifies total frames received from DCE device for a specific PVC within current 15 minutes interval.
OBJECT-TYPE    
  Counter  

dte-octets-pvc-curr 1.3.6.1.4.1.568.8.2.3.1.4
Identifies total octets received from DTE device for a specific PVC within current 15 minutes interval.
OBJECT-TYPE    
  Counter  

dce-octets-pvc-curr 1.3.6.1.4.1.568.8.2.3.1.5
Identifies total octets received from DTE device for a specific PVC within current 15 minutes interval.
OBJECT-TYPE    
  Counter  

dte-frames-with-DE-pvc-curr 1.3.6.1.4.1.568.8.2.3.1.6
Identifies total frames with DE bit set received from DTE device for a specific PVC within current 15 minutes interval.
OBJECT-TYPE    
  Counter  

dce-frames-with-DE-pvc-curr 1.3.6.1.4.1.568.8.2.3.1.7
Identifies total frames with DE bit set received from DCE device for a specific PVC within current 15 minutes interval.
OBJECT-TYPE    
  Counter  

fecn-frames-pvc-curr 1.3.6.1.4.1.568.8.2.3.1.8
Identifies total number of frames for a specific PVC with FECN set received within current 15 minutes interval.
OBJECT-TYPE    
  Counter  

becn-frames-pvc-curr 1.3.6.1.4.1.568.8.2.3.1.9
Identifies total number of frames for a specific PVC with BECN set received within current 15 minutes interval.
OBJECT-TYPE    
  Counter  

poll-tx-pvc-curr 1.3.6.1.4.1.568.8.2.3.1.10
Identifies total number of probe polls sent to DCE within current 15 minutes interval.
OBJECT-TYPE    
  Counter  

resp-tx-pvc-curr 1.3.6.1.4.1.568.8.2.3.1.11
Identifies total number of probe responses sent to DCE within current 15 minutes interval.
OBJECT-TYPE    
  Counter  

poll-rx-pvc-curr 1.3.6.1.4.1.568.8.2.3.1.12
Identifies total number of probe polls received from DCE on a specific PVC within current 15 minutes interval.
OBJECT-TYPE    
  Counter  

resp-rx-pvc-curr 1.3.6.1.4.1.568.8.2.3.1.13
Identifies total number of probe responses received from DCE on a specific PVC within current 15 minutes interval.
OBJECT-TYPE    
  Counter  

pvc-loop-curr 1.3.6.1.4.1.568.8.2.3.1.14
Identifies whether the specific PVC has been found to be in a loop back state by link probe's generator process.
OBJECT-TYPE    
  INTEGER loopback(1), no-loopback(2)  

ip-poll-tx-pvc-curr 1.3.6.1.4.1.568.8.2.3.1.15
Identifies total number of probe IP polls sent to ethernet within current 15 minutes interval.
OBJECT-TYPE    
  Counter  

ip-resp-tx-pvc-curr 1.3.6.1.4.1.568.8.2.3.1.16
Identifies total number of probe IP responses sent to ethernet within current 15 minutes interval.
OBJECT-TYPE    
  Counter  

ip-poll-rx-pvc-curr 1.3.6.1.4.1.568.8.2.3.1.17
Identifies total number of probe IP polls received from ethernet on a specific PVC within current 15 minutes interval.
OBJECT-TYPE    
  Counter  

ip-resp-rx-pvc-curr 1.3.6.1.4.1.568.8.2.3.1.18
Identifies total number of probe IP responses received from ethernet on a specific PVC within current 15 minutes interval.
OBJECT-TYPE    
  Counter  

ipRtrRxLatTxPvcCurr 1.3.6.1.4.1.568.8.2.3.1.19
Identifies total number of Router Receive Latency IP packets transmitted out the To-Dte port within current 15 minute interval.
OBJECT-TYPE    
  Counter  

ipRtrRxLatRxPvcCurr 1.3.6.1.4.1.568.8.2.3.1.20
Identifies total number of Router Receive Latency IP packets received at the Ethernet port within current 15 minute interval.
OBJECT-TYPE    
  Counter  

ipRtrTxLatTxPvcCurr 1.3.6.1.4.1.568.8.2.3.1.21
Identifies total number of Router Transmit Latency IP packets transmitted out the Ethernet port within current 15 minute interval.
OBJECT-TYPE    
  Counter  

ipRtrTxLatRxPvcCurr 1.3.6.1.4.1.568.8.2.3.1.22
Identifies total number of Router Transmit Latency IP packets received at the To-Dte port within current 15 minute interval.
OBJECT-TYPE    
  Counter  

pvcStInterval-Table 1.3.6.1.4.1.568.8.2.4
PVC statistic interval table:
OBJECT-TYPE    
  SEQUENCE OF  
    PVCStInterval-entry

pvcStInterval-Entry 1.3.6.1.4.1.568.8.2.4.1
Identifies an entry (row) in pvc statistic table
OBJECT-TYPE    
  PVCStInterval-entry  

pvc-number-index-intv 1.3.6.1.4.1.568.8.2.4.1.1
The index value which uniquely identifies the PVC number to which this entry is applicable.
OBJECT-TYPE    
  INTEGER 16..991  

pvcStIntv-index 1.3.6.1.4.1.568.8.2.4.1.2
A number between 1 and 96, where 1 is the most recently completed 15 minutes interval and 96 is the least recently completed 15 minutes interval.
OBJECT-TYPE    
  INTEGER 1..96  

dte-frames-pvc-intv 1.3.6.1.4.1.568.8.2.4.1.3
Identifies total frames received from DTE device for a specific PVC within a 15 minutes interval.
OBJECT-TYPE    
  Counter  

dce-frames-pvc-intv 1.3.6.1.4.1.568.8.2.4.1.4
Identifies total frames received from DCE device for a specific PVC within a 15 minutes interval.
OBJECT-TYPE    
  Counter  

dte-octets-pvc-intv 1.3.6.1.4.1.568.8.2.4.1.5
Identifies total octets received from DTE device for a specific PVC within a 15 minutes interval.
OBJECT-TYPE    
  Counter  

dce-octets-pvc-intv 1.3.6.1.4.1.568.8.2.4.1.6
Identifies total octets received from DTE device for a specific PVC within a 15 minutes interval.
OBJECT-TYPE    
  Counter  

dte-frames-with-DE-pvc-intv 1.3.6.1.4.1.568.8.2.4.1.7
Identifies the frames with DE bit set received from DTE device for a specific PVC within a 15 minutes interval.
OBJECT-TYPE    
  Counter  

dce-frames-with-DE-pvc-intv 1.3.6.1.4.1.568.8.2.4.1.8
Identifies the frames with DE bit set received from DCE device for a specific PVC within a 15 minutes interval.
OBJECT-TYPE    
  Counter  

fecn-frames-pvc-intv 1.3.6.1.4.1.568.8.2.4.1.9
Identifies total number of frames for a specific PVC with FECN set received within a 15 minutes interval.
OBJECT-TYPE    
  Counter  

becn-frames-pvc-intv 1.3.6.1.4.1.568.8.2.4.1.10
Identifies total number of frames for a specific PVC with BECN set received within a 15 minutes interval.
OBJECT-TYPE    
  Counter  

poll-tx-pvc-intv 1.3.6.1.4.1.568.8.2.4.1.11
Identifies total number of probe polls sent to DCE within a 15 minutes interval.
OBJECT-TYPE    
  Counter  

resp-tx-pvc-intv 1.3.6.1.4.1.568.8.2.4.1.12
Identifies total number of probe responses sent to DCE within a 15 minutes interval.
OBJECT-TYPE    
  Counter  

poll-rx-pvc-intv 1.3.6.1.4.1.568.8.2.4.1.13
Identifies total number of probe polls received from DCE on a specific PVC within a 15 minutes interval.
OBJECT-TYPE    
  Counter  

resp-rx-pvc-intv 1.3.6.1.4.1.568.8.2.4.1.14
Identifies total number of probe responses received from DCE on a specific PVC within a 15 minutes interval.
OBJECT-TYPE    
  Counter  

pvc-loop-intv 1.3.6.1.4.1.568.8.2.4.1.15
Identifies whether the specific PVC has been found to be in a loop back state by link probe's generator process.
OBJECT-TYPE    
  INTEGER  

ip-poll-tx-pvc-intv 1.3.6.1.4.1.568.8.2.4.1.16
Identifies total number of probe IP polls sent to ethernet within a 15 minutes interval.
OBJECT-TYPE    
  Counter  

ip-resp-tx-pvc-intv 1.3.6.1.4.1.568.8.2.4.1.17
Identifies total number of probe IP responses sent to ethernet within a 15 minutes interval.
OBJECT-TYPE    
  Counter  

ip-poll-rx-pvc-intv 1.3.6.1.4.1.568.8.2.4.1.18
Identifies total number of probe IP polls received from ethernet on a specific PVC within a 15 minutes interval.
OBJECT-TYPE    
  Counter  

ip-resp-rx-pvc-intv 1.3.6.1.4.1.568.8.2.4.1.19
Identifies total number of probe IP responses received from ethernet on a specific PVC within a 15 minutes interval.
OBJECT-TYPE    
  Counter  

ipRtrRxLatTxPvcIntv 1.3.6.1.4.1.568.8.2.4.1.20
Identifies total number of Router Receive Latency IP packets transmitted out the To-Dte port within a 15 minute interval.
OBJECT-TYPE    
  Counter  

ipRtrRxLatRxPvcIntv 1.3.6.1.4.1.568.8.2.4.1.21
Identifies total number of Router Receive Latency IP packets received at the Ethernet port within a 15 minute interval.
OBJECT-TYPE    
  Counter  

ipRtrTxLatTxPvcIntv 1.3.6.1.4.1.568.8.2.4.1.22
Identifies total number of Router Transmit Latency IP packets transmitted out the Ethernet port within a 15 minute interval.
OBJECT-TYPE    
  Counter  

ipRtrTxLatRxPvcIntv 1.3.6.1.4.1.568.8.2.4.1.23
Identifies total number of Router Transmit Latency IP packets received at the To-Dte port within a 15 minute interval.
OBJECT-TYPE    
  Counter  

chanPerfCurr 1.3.6.1.4.1.568.8.3.1
OBJECT IDENTIFIER    

chan-unvail-toDte-curr 1.3.6.1.4.1.568.8.3.1.1
This object identifies the channel unavailability due to remote DTE fault within the latest 15 minutes. This statistical data is calculated by the channel unavailable time over the full time interval.
OBJECT-TYPE    
  DisplayString Size(0..6)  

chan-unavail-toDce-curr 1.3.6.1.4.1.568.8.3.1.2
This object identifies the channel unavailability due to local DTE fault within the latest 15 minutes. This statistical data is calculated by the channel unavailable time over the full time interval.
OBJECT-TYPE    
  DisplayString Size(0..6)  

chan-user-load-tx-curr 1.3.6.1.4.1.568.8.3.1.3
channel average user tx load within the latest 15 minutes, this statistical data is calculated by user data octets sent by the channel within the 15 minutes over the total channel available load ( which depends on physical interface speed).
OBJECT-TYPE    
  DisplayString Size(0..6)  

chan-user-load-rx-curr 1.3.6.1.4.1.568.8.3.1.4
channel average user rx load within the latest 15 minutes, this statistical data is calculated by user data octets received by the channel within the 15 minutes over the total channel available load ( which depends on physical interface speed).
OBJECT-TYPE    
  DisplayString Size(0..6)  

chan-total-load-tx-curr 1.3.6.1.4.1.568.8.3.1.5
channel total tx load within the latest 15 minutes, this statistical data is calculated by the total data octets sent by the channel within the 15 minutes over the channel available load ( which depends on physical interface speed).
OBJECT-TYPE    
  DisplayString Size(0..6)  

chan-total-load-rx-curr 1.3.6.1.4.1.568.8.3.1.6
channel total rx load within the latest 15 minutes, this statistical data is calculated by total data octets received by the channel within the 15 minutes over the channel total available load ( which depends on physical interface speed).
OBJECT-TYPE    
  DisplayString Size(0..6)  

chanPerfIntv-Table 1.3.6.1.4.1.568.8.3.2
Probe channel performance table, which displays the performance statistical data based on the probe channel within previous 24 hours.
OBJECT-TYPE    
  SEQUENCE OF  
    ChanPerfIntv-Entry

chanPerfIntv-Entry 1.3.6.1.4.1.568.8.3.2.1
Identifies an entry (row) in probe channel performance table.
OBJECT-TYPE    
  ChanPerfIntv-Entry  

chanPerfIntv-index 1.3.6.1.4.1.568.8.3.2.1.1
Identifies an entry (row) in historical PVC performance table, total 96 time intervals, where 1 is the most recently completed 15 minutes interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).
OBJECT-TYPE    
  INTEGER 1..96  

chan-unavail-toDte-intv 1.3.6.1.4.1.568.8.3.2.1.2
This object identifies the channel unavailability due to remote DTE fault within a 15 minutes interval. This statistical data is calculated by the channel unavailable time over the full time interval.
OBJECT-TYPE    
  DisplayString Size(0..6)  

chan-unavail-toDce-intv 1.3.6.1.4.1.568.8.3.2.1.3
This object identifies the channel unavailability due to local DTE fault within a 15 minutes interval. This statistical data is calculated by the channel unavailable time over the full time interval.
OBJECT-TYPE    
  DisplayString Size(0..6)  

chan-user-load-tx-intv 1.3.6.1.4.1.568.8.3.2.1.4
channel average user tx load within a 15 minutes interval, this statistical data is calculated by user data octets sent by the channel within the 15 minutes over the total channel available load ( which depends on physical interface speed).
OBJECT-TYPE    
  DisplayString Size(0..6)  

chan-user-load-rx-intv 1.3.6.1.4.1.568.8.3.2.1.5
channel average user rx load within a 15 minutes interval, this statistical data is calculated by user data octets received by the channel within the 15 minutes over the total channel available load( which depends on physical interface speed).
OBJECT-TYPE    
  DisplayString Size(0..6)  

chan-total-load-tx-intv 1.3.6.1.4.1.568.8.3.2.1.6
channel total tx load within a 15 minutes interval, this statistical data is calculated by the total data octets sent by the channel within the 15 minutes over the total channel available load ( which depends on physical interface speed).
OBJECT-TYPE    
  DisplayString Size(0..6)  

chan-total-load-rx-intv 1.3.6.1.4.1.568.8.3.2.1.7
Channel total rx load within a 15 minutes interval, this statistical data is calculated by the total data octets received by the channel within the 15 minutes over the total channel available load ( which depends on physical interface speed).
OBJECT-TYPE    
  DisplayString Size(0..6)  

chan-min-user-load-tx-intv 1.3.6.1.4.1.568.8.3.2.1.8
Minimum chan-user-load-tx within a 15 minutes interval.
OBJECT-TYPE    
  DisplayString Size(0..6)  

chan-min-user-load-tx-time-intv 1.3.6.1.4.1.568.8.3.2.1.9
Timestamp of when the minimum chan-user-load-tx within a 15 minutes interval occurred.
OBJECT-TYPE    
  DisplayString Size(0..255)  

chan-min-user-load-rx-intv 1.3.6.1.4.1.568.8.3.2.1.10
Minimum chan-user-load-rx within a 15 minutes interval.
OBJECT-TYPE    
  DisplayString Size(0..6)  

chan-min-user-load-rx-time-intv 1.3.6.1.4.1.568.8.3.2.1.11
Timestamp of when the minimum chan-user-load-rx within a 15 minutes interval occurred.
OBJECT-TYPE    
  DisplayString Size(0..255)  

chan-min-total-load-tx-intv 1.3.6.1.4.1.568.8.3.2.1.12
Minimum chan-total-load-tx within a 15 minutes interval.
OBJECT-TYPE    
  DisplayString Size(0..6)  

chan-min-total-load-tx-time-intv 1.3.6.1.4.1.568.8.3.2.1.13
Timestamp of when the minimum chan-total-load-tx within a 15 minutes interval occurred.
OBJECT-TYPE    
  DisplayString Size(0..255)  

chan-min-total-load-rx-intv 1.3.6.1.4.1.568.8.3.2.1.14
Minimum chan-total-load-rx within a 15 minutes interval.
OBJECT-TYPE    
  DisplayString Size(0..6)  

chan-min-total-load-rx-time-intv 1.3.6.1.4.1.568.8.3.2.1.15
Timestamp of when the minimum chan-total-load-rx within a 15 minutes interval occurred.
OBJECT-TYPE    
  DisplayString Size(0..255)  

chan-max-user-load-tx-intv 1.3.6.1.4.1.568.8.3.2.1.16
Maximum chan-user-load-tx within a 15 minutes interval.
OBJECT-TYPE    
  DisplayString Size(0..6)  

chan-max-user-load-tx-time-intv 1.3.6.1.4.1.568.8.3.2.1.17
Timestamp of when the maximum chan-user-load-tx within a 15 minutes interval occurred.
OBJECT-TYPE    
  DisplayString Size(0..255)  

chan-max-user-load-rx-intv 1.3.6.1.4.1.568.8.3.2.1.18
Maximum chan-user-load-rx within a 15 minutes interval.
OBJECT-TYPE    
  DisplayString Size(0..6)  

chan-max-user-load-rx-time-intv 1.3.6.1.4.1.568.8.3.2.1.19
Timestamp of when the maximum chan-user-load-rx within a 15 minutes interval occurred.
OBJECT-TYPE    
  DisplayString Size(0..255)  

chan-max-total-load-tx-intv 1.3.6.1.4.1.568.8.3.2.1.20
Maximum chan-total-load-tx within a 15 minutes interval.
OBJECT-TYPE    
  DisplayString Size(0..6)  

chan-max-total-load-tx-time-intv 1.3.6.1.4.1.568.8.3.2.1.21
Timestamp of when the maximum chan-total-load-tx within a 15 minutes interval occurred.
OBJECT-TYPE    
  DisplayString Size(0..6)  

chan-max-total-load-rx-intv 1.3.6.1.4.1.568.8.3.2.1.22
Maximum chan-total-load-rx within a 15 minutes interval.
OBJECT-TYPE    
  DisplayString Size(0..6)  

chan-max-total-load-rx-time-intv 1.3.6.1.4.1.568.8.3.2.1.23
Timestamp of when the maximum chan-total-load-rx within a 15 minutes interval occurred.
OBJECT-TYPE    
  DisplayString Size(0..255)  

pvcPerfCurr-Table 1.3.6.1.4.1.568.8.3.3
PVC performance table, which displays the performance statistical data based on each PVC.
OBJECT-TYPE    
  SEQUENCE OF  
    PvcPerfCurr-Entry

pvcPerfCurr-Entry 1.3.6.1.4.1.568.8.3.3.1
Identifies an entry (row) in pvc statistic table
OBJECT-TYPE    
  PvcPerfCurr-Entry  

pvcPerfCurr-num-index 1.3.6.1.4.1.568.8.3.3.1.1
The index value which uniquely identifies the PVC number to which this entry is applicable.
OBJECT-TYPE    
  INTEGER 16..991  

pvc-tx-time-curr 1.3.6.1.4.1.568.8.3.3.1.2
Probe token average round trip time within the latest 15 minutes for a specific PVC. A -1 value indicates data is Not-Avail.
OBJECT-TYPE    
  INTEGER  

pvc-unavail-toDte 1.3.6.1.4.1.568.8.3.3.1.3
This object identifies the PVC average unavailability within the latest 15 minutes. This statistical data is calculated by a PVC unavailable time due to the network or remote DTE fault over the full time interval.
OBJECT-TYPE    
  DisplayString Size(0..6)  

pvc-unavail-toDce 1.3.6.1.4.1.568.8.3.3.1.4
This object identifies the PVC average unavailability within the latest 15 minutes. This statistical data is calculated by a PVC unavailable time due to the local DTE fault over the full time interval.
OBJECT-TYPE    
  DisplayString Size(0..6)  

pvc-user-load-tx-curr 1.3.6.1.4.1.568.8.3.3.1.5
This object identifies the PVC average user tx load within the latest 15 minutes. This statistical data is calculated by user data octets sent by a specific PVC within the 15 minutes over the PVC total available load. Note: If the CIR is correctly defined for this PVC, PVC available load will depend on CIR, otherwise, it will get it from interface speed.
OBJECT-TYPE    
  DisplayString Size(0..6)  

pvc-user-load-rx-curr 1.3.6.1.4.1.568.8.3.3.1.6
This object identifies the PVC average user rx load within the latest 15 minutes. This statistical data is calculated by user data octets received by a specific PVC within the 15 minutes over the PVC total available load. Note: If the CIR is correctly defined for this PVC, PVC available load will depend on CIR, otherwise, it will get it from interface speed.
OBJECT-TYPE    
  DisplayString Size(0..6)  

pvc-total-load-tx-curr 1.3.6.1.4.1.568.8.3.3.1.7
This object identifies the PVC total tx load within the latest 15 minutes. This statistical data is calculated by total data octets sent by a specific PVC within the 15 minutes over the PVC total available load. Note: If the CIR is correctly defined for this PVC, PVC available load will depend on CIR, otherwise, it will get it from interface speed.
OBJECT-TYPE    
  DisplayString Size(0..6)  

pvc-total-load-rx-curr 1.3.6.1.4.1.568.8.3.3.1.8
This object identifies the PVC total rx load within the latest 15 minutes. This statistical data is calculated by total data octets received by a specific PVC within the 15 minutes over the PVC total available load. Note: If the CIR is correctly defined for this PVC, PVC available load will depend on CIR, otherwise, it will get it from interface speed.
OBJECT-TYPE    
  DisplayString Size(0..6)  

pvc-CIR-toNet-exceed-curr 1.3.6.1.4.1.568.8.3.3.1.9
This object identifies the number of exceeding CIR times that the network detected within the current interval. The measurement is done for every Tc, and the direction is to the network.
OBJECT-TYPE    
  INTEGER  

pvc-EIR-toNet-exceed-curr 1.3.6.1.4.1.568.8.3.3.1.10
This object identifies the number of exceeding EIR times that the network detected within the current interval. The measurement is done for every Tc, and the direction is to the network.
OBJECT-TYPE    
  INTEGER  

pvc-loss-frame-tx-curr 1.3.6.1.4.1.568.8.3.3.1.11
This object identifies the percentage of tx loss of frames within the total tx frames for this PVC. A -1 value indicates data is Not-Avail.
OBJECT-TYPE    
  INTEGER  

pvc-loss-frame-rx-curr 1.3.6.1.4.1.568.8.3.3.1.12
This object identifies the percentage of rx loss of frames within the total rx frames for this PVC. A -1 value indicates data is Not-Avail.
OBJECT-TYPE    
  INTEGER  

pvc-ip-tx-time-curr 1.3.6.1.4.1.568.8.3.3.1.13
Probe token average round trip time via ethernet and using UDP/IP packets within the latest 15 minutes for a specific PVC. A -1 value indicates data is Not-Avail.
OBJECT-TYPE    
  INTEGER  

pvcIpRtrRxLatTxTimeCurr 1.3.6.1.4.1.568.8.3.3.1.14
Router Receive Latency IP Packet average round trip time from first byte transmitted out the To-Dte port, to the last byte received on the Ethernet port, within the latest 15 minutes for a specific PVC. A -1 value indicates data is Not-Avail.
OBJECT-TYPE    
  INTEGER  

pvcIpRtrTxLatTxTimeCurr 1.3.6.1.4.1.568.8.3.3.1.15
Router Transmit Latency IP Packet average round trip time from first byte transmitted out the Ethernet port, to the last byte received on the To-Dte port, within the latest 15 minutes for a specific PVC. A -1 value indicates data is Not-Avail.
OBJECT-TYPE    
  INTEGER  

pvcPerfIntv-Table 1.3.6.1.4.1.568.8.3.4
PVC performance interval table, which displays the performance statistical data based on each PVC in previous 24 hours.
OBJECT-TYPE    
  SEQUENCE OF  
    PvcPerfIntv-Entry

pvcPerfIntv-Entry 1.3.6.1.4.1.568.8.3.4.1
Identifies an entry (row) in pvc statistic table
OBJECT-TYPE    
  PvcPerfIntv-Entry  

pvcPerfIntv-num-index 1.3.6.1.4.1.568.8.3.4.1.1
The index value which uniquely identifies the PVC number to which this entry is applicable.
OBJECT-TYPE    
  INTEGER 16..991  

pvcPerf-intv-index 1.3.6.1.4.1.568.8.3.4.1.2
Identifies an entry (row) in PVC performance table, with total 96 time intervals, where 1 is the most recently completed 15 minutes interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).
OBJECT-TYPE    
  INTEGER 1..96  

pvc-tx-time-intv 1.3.6.1.4.1.568.8.3.4.1.3
Probe token average round trip time within a 15 minutes interval for a specific PVC. A -1 value indicates data is Not-Avail.
OBJECT-TYPE    
  INTEGER  

pvc-unavail-toDte-intv 1.3.6.1.4.1.568.8.3.4.1.4
This object identifies the PVC average unavailability within a 15 minutes interval. This statistical data is calculated by a PVC unavailable time due to the network or remote DTE fault over the full time interval.
OBJECT-TYPE    
  DisplayString Size(0..6)  

pvc-unavail-toDce-intv 1.3.6.1.4.1.568.8.3.4.1.5
This object identifies the PVC average unavailability within a 15 minutes interval. This statistical data is calculated by a PVC unavailable time due to the local DTE fault over the full time interval.
OBJECT-TYPE    
  DisplayString Size(0..6)  

pvc-user-load-tx-intv 1.3.6.1.4.1.568.8.3.4.1.6
This object identifies the PVC average user tx load within a 15 minutes interval. This statistical data is calculated by user data octets sent by a specific PVC within the 15 minutes over the PVC total available load. Note: If the CIR is correctly defined for this PVC, PVC available load will depend on CIR, otherwise, it will get it from interface speed.
OBJECT-TYPE    
  DisplayString Size(0..6)  

pvc-user-load-rx-intv 1.3.6.1.4.1.568.8.3.4.1.7
This object identifies the PVC average user rx load within a 15 minutes interval. This statistical data is calculated by user data octets received by a specific PVC within the 15 minutes over the PVC total available load. Note: If the CIR is correctly defined for this PVC, PVC available load will depend on CIR, otherwise, it will get it from interface speed.
OBJECT-TYPE    
  DisplayString Size(0..6)  

pvc-total-load-tx-intv 1.3.6.1.4.1.568.8.3.4.1.8
This object identifies the PVC total tx load within a 15 minutes interval. This statistical data is calculated by total data octets sent by a specific PVC within the 15 minutes over the PVC total available load. Note: If the CIR is correctly defined for this PVC, PVC available load will depend on CIR, otherwise, it will get it from interface speed.
OBJECT-TYPE    
  DisplayString Size(0..6)  

pvc-total-load-rx-intv 1.3.6.1.4.1.568.8.3.4.1.9
This object identifies the PVC total rx load within a 15 minutes interval. This statistical data is calculated by total data octets received by a specific PVC within the 15 minutes over the PVC total available load. Note: If the CIR is correctly defined for this PVC, PVC available load will depend on CIR, otherwise, it will get it from interface speed.
OBJECT-TYPE    
  DisplayString Size(0..6)  

pvc-CIR-toNet-exceed-intv 1.3.6.1.4.1.568.8.3.4.1.10
This object identifies the number of exceeding CIR times that the network detected within an interval. The measurement is done for every Tc, and the direction is to the network.
OBJECT-TYPE    
  INTEGER  

pvc-EIR-toNet-exceed-intv 1.3.6.1.4.1.568.8.3.4.1.11
This object identifies the number of exceeding EIR times that the network detected within an interval. The measurement is done for every Tc, and the direction is to the network.
OBJECT-TYPE    
  INTEGER  

pvc-loss-frame-tx-intv 1.3.6.1.4.1.568.8.3.4.1.12
This object identifies the percentage of tx loss of frames within the total tx frames for this PVC in this interval.
OBJECT-TYPE    
  INTEGER not-avail(255)  

pvc-loss-frame-rx-intv 1.3.6.1.4.1.568.8.3.4.1.13
This object identifies the percentage of rx loss of frames within the total rx frames for this PVC in this interval.
OBJECT-TYPE    
  INTEGER not-avail(255)  

pvc-ip-tx-time-intv 1.3.6.1.4.1.568.8.3.4.1.14
Probe token average round trip time via ethernet and using UDP/IP packets within a 15 minutes interval for a specific PVC. A -1 value indicates data is Not-Avail.
OBJECT-TYPE    
  INTEGER  

pvcIpRtrRxLatTxTimeIntv 1.3.6.1.4.1.568.8.3.4.1.15
Router Receive Latency IP Packet average round trip time from first byte transmitted out the To-Dte port, to the last byte received on the Ethernet port, within a 15 minute interval for a specific PVC. A -1 value indicates data is Not-Avail.
OBJECT-TYPE    
  INTEGER  

pvcIpRtrTxLatTxTimeIntv 1.3.6.1.4.1.568.8.3.4.1.16
Router Transmit Latency IP Packet average round trip time from first byte transmitted out the Ethernet port, to the last byte received on the To-Dte port, within a 15 minute interval for a specific PVC. A -1 value indicates data is Not-Avail.
OBJECT-TYPE    
  INTEGER  

pvc-min-tx-time-intv 1.3.6.1.4.1.568.8.3.4.1.17
Minimum pvc-tx-time within a 15 minutes interval for a specific PVC.
OBJECT-TYPE    
  INTEGER  

pvc-min-tx-time-time-intv 1.3.6.1.4.1.568.8.3.4.1.18
Timestamp of when the minimum pvc-tx-time within a 15 minutes interval occurred.
OBJECT-TYPE    
  DisplayString Size(0..255)  

pvc-min-user-load-tx-intv 1.3.6.1.4.1.568.8.3.4.1.19
Minimum pvc-user-load-tx within a 15 minutes interval.
OBJECT-TYPE    
  DisplayString Size(0..6)  

pvc-min-user-load-tx-time-intv 1.3.6.1.4.1.568.8.3.4.1.20
Timestamp of when the minimum pvc-user-load-tx within a 15 minutes interval occurred.
OBJECT-TYPE    
  DisplayString Size(0..255)  

pvc-min-user-load-rx-intv 1.3.6.1.4.1.568.8.3.4.1.21
Minimum pvc-user-load-rx within a 15 minutes interval.
OBJECT-TYPE    
  DisplayString Size(0..6)  

pvc-min-user-load-rx-time-intv 1.3.6.1.4.1.568.8.3.4.1.22
Timestamp of when the minimum pvc-user-load-rx within a 15 minutes interval occurred.
OBJECT-TYPE    
  DisplayString Size(0..255)  

pvc-min-total-load-tx-intv 1.3.6.1.4.1.568.8.3.4.1.23
Minimum pvc-total-load-tx within a 15 minutes interval.
OBJECT-TYPE    
  DisplayString Size(0..6)  

pvc-min-total-load-tx-time-intv 1.3.6.1.4.1.568.8.3.4.1.24
Timestamp of when the minimum pvc-total-load-tx within a 15 minutes interval occurred.
OBJECT-TYPE    
  DisplayString Size(0..255)  

pvc-min-total-load-rx-intv 1.3.6.1.4.1.568.8.3.4.1.25
Minimum pvc-total-load-rx within a 15 minutes interval.
OBJECT-TYPE    
  DisplayString Size(0..6)  

pvc-min-total-load-rx-time-intv 1.3.6.1.4.1.568.8.3.4.1.26
Timestamp of when the minimum pvc-total-load-rx within a 15 minutes interval occurred.
OBJECT-TYPE    
  DisplayString Size(0..255)  

pvc-min-ip-tx-time-intv 1.3.6.1.4.1.568.8.3.4.1.27
Minimum pvc-ip-tx-time within a 15 minutes interval.
OBJECT-TYPE    
  INTEGER  

pvc-min-ip-tx-time-time-intv 1.3.6.1.4.1.568.8.3.4.1.28
Timestamp of when the minimum pvc-ip-tx-time within a 15 minutes interval occurred.
OBJECT-TYPE    
  DisplayString Size(0..255)  

pvc-max-tx-time-intv 1.3.6.1.4.1.568.8.3.4.1.29
Maximum pvc-tx-time within a 15 minutes interval.
OBJECT-TYPE    
  INTEGER  

pvc-max-tx-time-time-intv 1.3.6.1.4.1.568.8.3.4.1.30
Timestamp of when the maximum pvc-tx-time within a 15 minutes interval occurred.
OBJECT-TYPE    
  DisplayString Size(0..255)  

pvc-max-user-load-tx-intv 1.3.6.1.4.1.568.8.3.4.1.31
Maximum pvc-user-load-tx within a 15 minutes interval.
OBJECT-TYPE    
  DisplayString Size(0..6)  

pvc-max-user-load-tx-time-intv 1.3.6.1.4.1.568.8.3.4.1.32
Timestamp of when the maximum pvc-user-load-tx within a 15 minutes interval occurred.
OBJECT-TYPE    
  DisplayString Size(0..255)  

pvc-max-user-load-rx-intv 1.3.6.1.4.1.568.8.3.4.1.33
Maximum pvc-user-load-rx within a 15 minutes interval.
OBJECT-TYPE    
  DisplayString Size(0..6)  

pvc-max-user-load-rx-time-intv 1.3.6.1.4.1.568.8.3.4.1.34
Timestamp of when the maximum pvc-user-load-rx within a 15 minutes interval occurred.
OBJECT-TYPE    
  DisplayString Size(0..255)  

pvc-max-total-load-tx-intv 1.3.6.1.4.1.568.8.3.4.1.35
Maximum pvc-total-load-tx within a 15 minutes interval.
OBJECT-TYPE    
  DisplayString Size(0..6)  

pvc-max-total-load-tx-time-intv 1.3.6.1.4.1.568.8.3.4.1.36
Timestamp of when the maximum pvc-total-load-tx within a 15 minutes interval occurred.
OBJECT-TYPE    
  DisplayString Size(0..255)  

pvc-max-total-load-rx-intv 1.3.6.1.4.1.568.8.3.4.1.37
Maximum pvc-total-load-rx within a 15 minutes interval.
OBJECT-TYPE    
  DisplayString Size(0..6)  

pvc-max-total-load-rx-time-intv 1.3.6.1.4.1.568.8.3.4.1.38
Timestamp of when the maximum pvc-total-load-rx within a 15 minutes interval occurred.
OBJECT-TYPE    
  DisplayString Size(0..255)  

pvc-max-ip-tx-time-intv 1.3.6.1.4.1.568.8.3.4.1.39
Maximum pvc-ip-tx-time within a 15 minutes interval.
OBJECT-TYPE    
  INTEGER  

pvc-max-ip-tx-time-time-intv 1.3.6.1.4.1.568.8.3.4.1.40
Timestamp of when the maximum pvc-ip-tx-time within a 15 minutes interval occurred.
OBJECT-TYPE    
  DisplayString Size(0..255)  

pvcShapeThresh 1.3.6.1.4.1.568.8.4.1
OBJECT IDENTIFIER    

pvcShapeThreshLevel-1 1.3.6.1.4.1.568.8.4.1.1
This parameter defines the maximum percentage of PVC traffic (measured in TC) within this PVC CIR in shape level 1 (currently is 10%).
OBJECT-TYPE    
  INTEGER 0..100  

pvcShapeThreshLevel-2 1.3.6.1.4.1.568.8.4.1.2
This parameter defines the maximum percentage of PVC traffic (measured in TC) within this PVC CIR in shape level 2 (currently is 25%).
OBJECT-TYPE    
  INTEGER 0..100  

pvcShapeThreshLevel-3 1.3.6.1.4.1.568.8.4.1.3
This parameter defines the maximum percentage of PVC traffic (measured in TC) within this PVC CIR in shape level 3 (currently is 45%).
OBJECT-TYPE    
  INTEGER 0..100  

pvcShapeThreshLevel-4 1.3.6.1.4.1.568.8.4.1.4
This parameter defines the maximum percentage of PVC traffic (measured in TC) within this PVC CIR in shape level 4 (currently is 75%).
OBJECT-TYPE    
  INTEGER 0..100  

pvcShapeThreshLevel-5 1.3.6.1.4.1.568.8.4.1.5
This parameter defines the maximum percentage of PVC traffic (measured in TC) within this PVC CIR in shape level 5 (currently is 90%).
OBJECT-TYPE    
  INTEGER 0..100  

pvcShapeThreshLevel-6 1.3.6.1.4.1.568.8.4.1.6
This parameter defines the maximum percentage of PVC traffic (measured in TC) within this PVC CIR in shape level 6 (currently is 100%).
OBJECT-TYPE    
  INTEGER 0..100  

pvcShapeThreshLevel-7 1.3.6.1.4.1.568.8.4.1.7
This parameter defines the maximum percentage of PVC traffic (measured in TC) within this PVC CIR in shape level 7 (currently is more than 100%).
OBJECT-TYPE    
  INTEGER  

pvcShapeCurrToDce-Table 1.3.6.1.4.1.568.8.4.2
PVC current traffic shape to DCE table, which displays the traffic shape information based on each PVC.
OBJECT-TYPE    
  SEQUENCE OF  
    PvcShapeCurrToDce-Entry

pvcShapeCurrToDce-Entry 1.3.6.1.4.1.568.8.4.2.1
Identifies an entry (row) in pvc current traffic shape to DCE table
OBJECT-TYPE    
  PvcShapeCurrToDce-Entry  

pvcShapeCurrToDce-index 1.3.6.1.4.1.568.8.4.2.1.1
The index value which uniquely identifies the PVC number to which this entry is applicable.
OBJECT-TYPE    
  INTEGER 16..991  

pvcShapeCurrToDceLevel-1 1.3.6.1.4.1.568.8.4.2.1.2
This object identifies the percentage of traffic in level one in current 15 minutes to the direction of DCE.
OBJECT-TYPE    
  INTEGER 0..100  

pvcShapeCurrToDceLevel-2 1.3.6.1.4.1.568.8.4.2.1.3
This object identifies the percentage of traffic in level two in current 15 minutes to the direction of DCE.
OBJECT-TYPE    
  INTEGER 0..100  

pvcShapeCurrToDceLevel-3 1.3.6.1.4.1.568.8.4.2.1.4
This object identifies the percentage of traffic in level three in current 15 minutes to the direction of DCE.
OBJECT-TYPE    
  INTEGER 0..100  

pvcShapeCurrToDceLevel-4 1.3.6.1.4.1.568.8.4.2.1.5
This object identifies the percentage of traffic in level four in current 15 minutes to the direction of DCE.
OBJECT-TYPE    
  INTEGER 0..100  

pvcShapeCurrToDceLevel-5 1.3.6.1.4.1.568.8.4.2.1.6
This object identifies the percentage of traffic in level five in current 15 minutes to the direction of DCE.
OBJECT-TYPE    
  INTEGER 0..100  

pvcShapeCurrToDceLevel-6 1.3.6.1.4.1.568.8.4.2.1.7
This object identifies the percentage of traffic in level six in current 15 minutes to the direction of DCE.
OBJECT-TYPE    
  INTEGER 0..100  

pvcShapeCurrToDceLevel-7 1.3.6.1.4.1.568.8.4.2.1.8
This object identifies the percentage of traffic in level seven in current 15 minutes to the direction of DCE.
OBJECT-TYPE    
  INTEGER 0..100  

pvcShapeCurrToDte-Table 1.3.6.1.4.1.568.8.4.3
PVC current traffic shape table, which displays the traffic shape information based on each PVC.
OBJECT-TYPE    
  SEQUENCE OF  
    PvcShapeCurrToDte-Entry

pvcShapeCurrToDte-Entry 1.3.6.1.4.1.568.8.4.3.1
Identifies an entry (row) in pvc current traffic shape to DTE table
OBJECT-TYPE    
  PvcShapeCurrToDte-Entry  

pvcShapeCurrToDte-index 1.3.6.1.4.1.568.8.4.3.1.1
The index value which uniquely identifies the PVC number to which this entry is applicable.
OBJECT-TYPE    
  INTEGER 16..991  

pvcShapeCurrToDteLevel-1 1.3.6.1.4.1.568.8.4.3.1.2
This object identifies the percentage of traffic in level one in current 15 minutes to the direction of DTE.
OBJECT-TYPE    
  INTEGER 0..100  

pvcShapeCurrToDteLevel-2 1.3.6.1.4.1.568.8.4.3.1.3
This object identifies the percentage of traffic in level two in current 15 minutes to the direction of DTE.
OBJECT-TYPE    
  INTEGER 0..100  

pvcShapeCurrToDteLevel-3 1.3.6.1.4.1.568.8.4.3.1.4
This object identifies the percentage of traffic in level three in current 15 minutes to the direction of DTE.
OBJECT-TYPE    
  INTEGER 0..100  

pvcShapeCurrToDteLevel-4 1.3.6.1.4.1.568.8.4.3.1.5
This object identifies the percentage of traffic in level four in current 15 minutes to the direction of DTE.
OBJECT-TYPE    
  INTEGER 0..100  

pvcShapeCurrToDteLevel-5 1.3.6.1.4.1.568.8.4.3.1.6
This object identifies the percentage of traffic in level five in current 15 minutes to the direction of DTE.
OBJECT-TYPE    
  INTEGER 0..100  

pvcShapeCurrToDteLevel-6 1.3.6.1.4.1.568.8.4.3.1.7
This object identifies the percentage of traffic in level six in current 15 minutes to the direction of DTE.
OBJECT-TYPE    
  INTEGER 0..100  

pvcShapeCurrToDteLevel-7 1.3.6.1.4.1.568.8.4.3.1.8
This object identifies the percentage of traffic in level seven in current 15 minutes to the direction of DTE.
OBJECT-TYPE    
  INTEGER 0..100  

pvcShapeIntvToDce-Table 1.3.6.1.4.1.568.8.4.4
PVC shape to DCE interval table, which displays the pvc traffic shape information to the direction of DCE within 24 hours.
OBJECT-TYPE    
  SEQUENCE OF  
    PvcShapeIntvToDce-Entry

pvcShapeIntvToDce-Entry 1.3.6.1.4.1.568.8.4.4.1
Identifies an entry (row) in pvc traffic shape to DCE interval table
OBJECT-TYPE    
  PvcShapeIntvToDce-Entry  

pvcShapeIntvToDce-pvcIx 1.3.6.1.4.1.568.8.4.4.1.1
The index value which uniquely identifies the PVC number to which this entry is applicable.
OBJECT-TYPE    
  INTEGER 16..991  

pvcShapeIntvToDce-intvIx 1.3.6.1.4.1.568.8.4.4.1.2
The index value which uniquely identifies the interval number to which this entry is applicable.
OBJECT-TYPE    
  INTEGER 1..96  

pvcShapeIntvToDceLevel-1 1.3.6.1.4.1.568.8.4.4.1.3
This object identifies the percentage of traffic in level one within a specific 15-minutes interval in the direction of DCE.
OBJECT-TYPE    
  INTEGER 0..100  

pvcShapeIntvToDceLevel-2 1.3.6.1.4.1.568.8.4.4.1.4
This object identifies the percentage of traffic in level two within a specific 15-minutes interval in the direction of DCE.
OBJECT-TYPE    
  INTEGER 0..100  

pvcShapeIntvToDceLevel-3 1.3.6.1.4.1.568.8.4.4.1.5
This object identifies the percentage of traffic in level three within a specific 15-minutes interval in the direction of DCE.
OBJECT-TYPE    
  INTEGER 0..100  

pvcShapeIntvToDceLevel-4 1.3.6.1.4.1.568.8.4.4.1.6
This object identifies the percentage of traffic in level four within a specific 15-minutes interval in the direction of DCE.
OBJECT-TYPE    
  INTEGER 0..100  

pvcShapeIntvToDceLevel-5 1.3.6.1.4.1.568.8.4.4.1.7
This object identifies the percentage of traffic in level five within a specific 15-minutes interval in the direction of DCE.
OBJECT-TYPE    
  INTEGER 0..100  

pvcShapeIntvToDceLevel-6 1.3.6.1.4.1.568.8.4.4.1.8
This object identifies the percentage of traffic in level six within a specific 15-minutes interval in the direction of DCE.
OBJECT-TYPE    
  INTEGER 0..100  

pvcShapeIntvToDceLevel-7 1.3.6.1.4.1.568.8.4.4.1.9
This object identifies the percentage of traffic in level seven within a specific 15-minutes interval in the direction of DCE.
OBJECT-TYPE    
  INTEGER 0..100  

pvcShapeIntvToDte-Table 1.3.6.1.4.1.568.8.4.5
PVC shape to DTE interval table, which displays the pvc traffic information to the direction of DTE within 24 hours.
OBJECT-TYPE    
  SEQUENCE OF  
    PvcShapeIntvToDte-Entry

pvcShapeIntvToDte-Entry 1.3.6.1.4.1.568.8.4.5.1
Identifies an entry (row) in pvc traffic shape to DTE interval table
OBJECT-TYPE    
  PvcShapeIntvToDte-Entry  

pvcShapeIntvToDte-pvcIx 1.3.6.1.4.1.568.8.4.5.1.1
The index value which uniquely identifies the PVC number to which this entry is applicable.
OBJECT-TYPE    
  INTEGER 16..991  

pvcShapeIntvToDte-intvIx 1.3.6.1.4.1.568.8.4.5.1.2
The index value which uniquely identifies the interval number to which this entry is applicable.
OBJECT-TYPE    
  INTEGER 1..96  

pvcShapeIntvToDteLevel-1 1.3.6.1.4.1.568.8.4.5.1.3
This object identifies the percentage of traffic in level one within a specific 15-minutes interval in the direction of DTE.
OBJECT-TYPE    
  INTEGER 0..100  

pvcShapeIntvToDteLevel-2 1.3.6.1.4.1.568.8.4.5.1.4
This object identifies the percentage of traffic in level two within a specific 15-minutes interval in the direction of DTE.
OBJECT-TYPE    
  INTEGER 0..100  

pvcShapeIntvToDteLevel-3 1.3.6.1.4.1.568.8.4.5.1.5
This object identifies the percentage of traffic in level three within a specific 15-minutes interval in the direction of DTE.
OBJECT-TYPE    
  INTEGER 0..100  

pvcShapeIntvToDteLevel-4 1.3.6.1.4.1.568.8.4.5.1.6
This object identifies the percentage of traffic in level four within a specific 15-minutes interval in the direction of DTE.
OBJECT-TYPE    
  INTEGER 0..100  

pvcShapeIntvToDteLevel-5 1.3.6.1.4.1.568.8.4.5.1.7
This object identifies the percentage of traffic in level five within a specific 15-minutes interval in the direction of DTE.
OBJECT-TYPE    
  INTEGER 0..100  

pvcShapeIntvToDteLevel-6 1.3.6.1.4.1.568.8.4.5.1.8
This object identifies the percentage of traffic in level six within a specific 15-minutes interval in the direction of DTE.
OBJECT-TYPE    
  INTEGER 0..100  

pvcShapeIntvToDteLevel-7 1.3.6.1.4.1.568.8.4.5.1.9
This object identifies the percentage of traffic in level seven within a specific 15-minutes interval in the direction of DTE.
OBJECT-TYPE    
  INTEGER 0..100  

histIntvStartTimeIntv-Table 1.3.6.1.4.1.568.8.5.1
Probe historical interval start time table, which displays the interval starting time for each interval covering an historical 3 hours.
OBJECT-TYPE    
  SEQUENCE OF  
    HistIntvStartTimeIntv-Entry

histIntvStartTimeIntv-Entry 1.3.6.1.4.1.568.8.5.1.1
Identifies an entry (row) in probe interval start time interval table.
OBJECT-TYPE    
  HistIntvStartTimeIntv-Entry  

histIntvStartTimeIntv-index 1.3.6.1.4.1.568.8.5.1.1.1
Identifies an entry (row) in historical PVC performance table, total 12 time intervals, where 1 is the most recently completed 15 minutes interval and 12 is the least recently completed 15 minutes interval (assuming that all 12 intervals are valid).
OBJECT-TYPE    
  INTEGER 1..12  

hist-intv-start-time 1.3.6.1.4.1.568.8.5.1.1.2
hist-intv-start-time displays the current interval starting time with 4 digits year, 2 digits month, 2 digits date and hours, minutes and seconds, which are each 2 digits.
OBJECT-TYPE    
  DisplayString Size(0..255)  

histChanPerfIntv-Table 1.3.6.1.4.1.568.8.5.2
Probe channel performance table, which displays the performance statistical data based on the probe channel covering an historical 3 hours.
OBJECT-TYPE    
  SEQUENCE OF  
    HistChanPerfIntv-Entry

histChanPerfIntv-Entry 1.3.6.1.4.1.568.8.5.2.1
Identifies an entry (row) in probe historical channel performance table.
OBJECT-TYPE    
  HistChanPerfIntv-Entry  

histChanPerfIntv-index 1.3.6.1.4.1.568.8.5.2.1.1
Identifies an entry (row) in historical PVC performance table, total 12 time intervals, where 1 is the most recently completed 15 minutes interval and 12 is the least recently completed 15 minutes interval (assuming that all 12 intervals are valid).
OBJECT-TYPE    
  INTEGER 1..12  

hist-chan-unavail-toDte-intv 1.3.6.1.4.1.568.8.5.2.1.2
This object identifies the channel unavailability due to remote DTE fault within a 15 minute interval. This statistical data is calculated by the channel unavailable time over the full time interval.
OBJECT-TYPE    
  DisplayString Size(0..6)  

hist-chan-unavail-toDce-intv 1.3.6.1.4.1.568.8.5.2.1.3
This object identifies the channel unavailability due to local DTE fault within a 15 minutes interval. This statistical data is calculated by the channel unavailable time over the full time interval.
OBJECT-TYPE    
  DisplayString Size(0..6)  

hist-chan-user-load-tx-intv 1.3.6.1.4.1.568.8.5.2.1.4
channel average user tx load within a 15 minute interval, this statistical data is calculated by user data octets sent by the channel within the 15 minutes over the total channel available load ( which depends on physical interface speed).
OBJECT-TYPE    
  DisplayString Size(0..6)  

hist-chan-user-load-rx-intv 1.3.6.1.4.1.568.8.5.2.1.5
channel average user rx load within a 15 minute interval, this statistical data is calculated by user data octets received by the channel within the 15 minutes over the total channel available load( which depends on physical interface speed).
OBJECT-TYPE    
  DisplayString Size(0..6)  

histPvcPerfIntv-Table 1.3.6.1.4.1.568.8.5.3
PVC performance interval table, which displays the performance statistical data based on each PVC in an historical 3 hours.
OBJECT-TYPE    
  SEQUENCE OF  
    HistPvcPerfIntv-Entry

histPvcPerfIntv-Entry 1.3.6.1.4.1.568.8.5.3.1
Identifies an entry (row) in pvc statistic table
OBJECT-TYPE    
  HistPvcPerfIntv-Entry  

histPvcPerfIntv-num-index 1.3.6.1.4.1.568.8.5.3.1.1
The index value which uniquely identifies the PVC number to which this entry is applicable.
OBJECT-TYPE    
  INTEGER 16..991  

histPvcPerf-intv-index 1.3.6.1.4.1.568.8.5.3.1.2
Identifies an entry (row) in historical PVC performance table, total 12 time intervals, where 1 is the most recently completed 15 minutes interval and 12 is the least recently completed 15 minutes interval (assuming that all 12 intervals are valid).
OBJECT-TYPE    
  INTEGER 1..12  

hist-pvc-tx-time-intv 1.3.6.1.4.1.568.8.5.3.1.3
Probe token average round trip time within a 15 minutes interval for a specific PVC. A -1 value indicates data is Not-Avail.
OBJECT-TYPE    
  INTEGER  

hist-pvc-unavail-toDte-intv 1.3.6.1.4.1.568.8.5.3.1.4
This object identifies the PVC average unavailability within a 15 minutes interval. This statistical data is calculated by a PVC unavailable time due to the network or remote DTE fault over the full time interval.
OBJECT-TYPE    
  DisplayString Size(0..6)  

hist-pvc-unavail-toDce-intv 1.3.6.1.4.1.568.8.5.3.1.5
This object identifies the PVC average unavailability within a 15 minutes interval. This statistical data is calculated by a PVC unavailable time due to the local DTE fault over the full time interval.
OBJECT-TYPE    
  DisplayString Size(0..6)  

hist-pvc-user-load-tx-intv 1.3.6.1.4.1.568.8.5.3.1.6
This object identifies the PVC average user tx load within a 15 minutes interval. This statistical data is calculated by user data octets sent by a specific PVC within the 15 minutes over the PVC total available load. Note: If the CIR is correctly defined for this PVC, PVC available load will depend on CIR, otherwise, it will get it from interface speed.
OBJECT-TYPE    
  DisplayString Size(0..6)  

hist-pvc-user-load-rx-intv 1.3.6.1.4.1.568.8.5.3.1.7
This object identifies the PVC average user rx load within a 15 minutes interval. This statistical data is calculated by user data octets received by a specific PVC within the 15 minutes over the PVC total available load. Note: If the CIR is correctly defined for this PVC, PVC available load will depend on CIR, otherwise, it will get it from interface speed.
OBJECT-TYPE    
  DisplayString Size(0..6)  

hist-pvc-CIR-toNet-exceed-intv 1.3.6.1.4.1.568.8.5.3.1.8
This object identifies the number of exceeding CIR times that the network detected within an interval. The measurement is done for every Tc, and the direction is to the network.
OBJECT-TYPE    
  INTEGER  

hist-pvc-loss-frame-tx-intv 1.3.6.1.4.1.568.8.5.3.1.9
This object identifies the percentage of tx loss of frames within the total tx frames for this PVC in this interval.
OBJECT-TYPE    
  INTEGER no-resp(254), not-avail(255)  

hist-pvc-loss-frame-rx-intv 1.3.6.1.4.1.568.8.5.3.1.10
This object identifies the percentage of rx loss of frames within the total rx frames for this PVC in this interval.
OBJECT-TYPE    
  INTEGER no-resp(254), not-avail(255)  

histPvcShapeIntvToDce-Table 1.3.6.1.4.1.568.8.5.4
PVC shape to DCE interval table, which displays the pvc traffic shape information to the direction of DCE over 3 previous hours.
OBJECT-TYPE    
  SEQUENCE OF  
    HistPvcShapeIntvToDce-Entry

histPvcShapeIntvToDce-Entry 1.3.6.1.4.1.568.8.5.4.1
Identifies an entry (row) in pvc traffic shape to DCE interval table
OBJECT-TYPE    
  HistPvcShapeIntvToDce-Entry  

histPvcShapeIntvToDce-pvcIx 1.3.6.1.4.1.568.8.5.4.1.1
The index value which uniquely identifies the PVC number to which this entry is applicable.
OBJECT-TYPE    
  INTEGER 16..991  

histPvcShapeIntvToDce-intvIx 1.3.6.1.4.1.568.8.5.4.1.2
The index value which uniquely identifies the interval number to which this entry is applicable.
OBJECT-TYPE    
  INTEGER 1..12  

histPvcShapeIntvToDceLevel-1 1.3.6.1.4.1.568.8.5.4.1.3
This object identifies the percentage of traffic in level one within a specific 15-minutes interval in the direction of DCE.
OBJECT-TYPE    
  INTEGER 0..100  

histPvcShapeIntvToDceLevel-2 1.3.6.1.4.1.568.8.5.4.1.4
This object identifies the percentage of traffic in level two within a specific 15-minutes interval in the direction of DCE.
OBJECT-TYPE    
  INTEGER 0..100  

histPvcShapeIntvToDceLevel-3 1.3.6.1.4.1.568.8.5.4.1.5
This object identifies the percentage of traffic in level three within a specific 15-minutes interval in the direction of DCE.
OBJECT-TYPE    
  INTEGER 0..100  

histPvcShapeIntvToDceLevel-4 1.3.6.1.4.1.568.8.5.4.1.6
This object identifies the percentage of traffic in level four within a specific 15-minutes interval in the direction of DCE.
OBJECT-TYPE    
  INTEGER 0..100  

histPvcShapeIntvToDceLevel-5 1.3.6.1.4.1.568.8.5.4.1.7
This object identifies the percentage of traffic in level five within a specific 15-minutes interval in the direction of DCE.
OBJECT-TYPE    
  INTEGER 0..100  

histPvcShapeIntvToDceLevel-6 1.3.6.1.4.1.568.8.5.4.1.8
This object identifies the percentage of traffic in level six within a specific 15-minutes interval in the direction of DCE.
OBJECT-TYPE    
  INTEGER 0..100  

histPvcShapeIntvToDceLevel-7 1.3.6.1.4.1.568.8.5.4.1.9
This object identifies the percentage of traffic in level seven within a specific 15-minutes interval in the direction of DCE.
OBJECT-TYPE    
  INTEGER 0..100  

histPvcShapeIntvToDte-Table 1.3.6.1.4.1.568.8.5.5
PVC shape to DTE interval table, which displays the pvc traffic information to the direction of DTE over 3 previous hours.
OBJECT-TYPE    
  SEQUENCE OF  
    HistPvcShapeIntvToDte-Entry

histPvcShapeIntvToDte-Entry 1.3.6.1.4.1.568.8.5.5.1
Identifies an entry (row) in pvc traffic shape to DTE interval table
OBJECT-TYPE    
  HistPvcShapeIntvToDte-Entry  

histPvcShapeIntvToDte-pvcIx 1.3.6.1.4.1.568.8.5.5.1.1
The index value which uniquely identifies the PVC number to which this entry is applicable.
OBJECT-TYPE    
  INTEGER 16..991  

histPvcShapeIntvToDte-intvIx 1.3.6.1.4.1.568.8.5.5.1.2
The index value which uniquely identifies the interval number to which this entry is applicable.
OBJECT-TYPE    
  INTEGER 1..12  

histPvcShapeIntvToDteLevel-1 1.3.6.1.4.1.568.8.5.5.1.3
This object identifies the percentage of traffic in level one within a specific 15-minutes interval in the direction of DTE.
OBJECT-TYPE    
  INTEGER 0..100  

histPvcShapeIntvToDteLevel-2 1.3.6.1.4.1.568.8.5.5.1.4
This object identifies the percentage of traffic in level two within a specific 15-minutes interval in the direction of DTE.
OBJECT-TYPE    
  INTEGER 0..100  

histPvcShapeIntvToDteLevel-3 1.3.6.1.4.1.568.8.5.5.1.5
This object identifies the percentage of traffic in level three within a specific 15-minutes interval in the direction of DTE.
OBJECT-TYPE    
  INTEGER 0..100  

histPvcShapeIntvToDteLevel-4 1.3.6.1.4.1.568.8.5.5.1.6
This object identifies the percentage of traffic in level four within a specific 15-minutes interval in the direction of DTE.
OBJECT-TYPE    
  INTEGER 0..100  

histPvcShapeIntvToDteLevel-5 1.3.6.1.4.1.568.8.5.5.1.7
This object identifies the percentage of traffic in level five within a specific 15-minutes interval in the direction of DTE.
OBJECT-TYPE    
  INTEGER 0..100  

histPvcShapeIntvToDteLevel-6 1.3.6.1.4.1.568.8.5.5.1.8
This object identifies the percentage of traffic in level six within a specific 15-minutes interval in the direction of DTE.
OBJECT-TYPE    
  INTEGER 0..100  

histPvcShapeIntvToDteLevel-7 1.3.6.1.4.1.568.8.5.5.1.9
This object identifies the percentage of traffic in level seven within a specific 15-minutes interval in the direction of DTE.
OBJECT-TYPE    
  INTEGER 0..100  

intvStartTimeIntv-Table 1.3.6.1.4.1.568.8.6.1
Probe interval start time table, which displays the interval starting time for each interval covering the last 24 hours.
OBJECT-TYPE    
  SEQUENCE OF  
    IntvStartTimeIntv-Entry

intvStartTimeIntv-Entry 1.3.6.1.4.1.568.8.6.1.1
Identifies an entry (row) in probe interval start time interval table.
OBJECT-TYPE    
  IntvStartTimeIntv-Entry  

intvStartTimeIntv-index 1.3.6.1.4.1.568.8.6.1.1.1
Identifies an entry (row) in interval start time table, total 96 time intervals, where 1 is the most recently completed 15 minutes interval and 96 is the least recently completed 15 minutes interval.
OBJECT-TYPE    
  INTEGER 1..96  

intv-start-time 1.3.6.1.4.1.568.8.6.1.1.2
intv-start-time displays the current interval starting time with 4 digits year, 2 digits month, 2 digits date and hours, minutes and seconds, which are each 2 digits.
OBJECT-TYPE    
  DisplayString Size(0..255)  

dbuPVCTable 1.3.6.1.4.1.568.8.7.1
DBU PVC table. It contains PVC/DLCI Dial-Backup information
OBJECT-TYPE    
  SEQUENCE OF  
    DbuPVCEntry

dbuPVCEntry 1.3.6.1.4.1.568.8.7.1.1
Identifies an entry (row) in dbuPVCTable.
OBJECT-TYPE    
  DbuPVCEntry  

dbuPVCTableIndex 1.3.6.1.4.1.568.8.7.1.1.1
Identifies an entry (row) in PVC table as the local PVC (DLCI) Number.
OBJECT-TYPE    
  INTEGER 16..991  

dbuRemotePVCDlci 1.3.6.1.4.1.568.8.7.1.1.2
Defines the remote PVC's DLCI number the data is to be routed to.
OBJECT-TYPE    
  INTEGER 16..991  

dbuIsdnAddress 1.3.6.1.4.1.568.8.7.1.1.3
Defines the ISDN Dialing Address to reach the PVC's backup site
OBJECT-TYPE    
  DisplayString Size(0..26)  

dbuPvcCir 1.3.6.1.4.1.568.8.7.1.1.4
This parameter defines the maximum transfer information rate (Bits Per Second) toward the backup PVC.
OBJECT-TYPE    
  INTEGER 0..2048000  

dbuMasterSlave 1.3.6.1.4.1.568.8.7.2
Defines whether the DBU probe is a Master or Slave.
OBJECT-TYPE    
  INTEGER slave(1), master(2)  

dbuBackupType 1.3.6.1.4.1.568.8.7.3
Defines the type of backup.
OBJECT-TYPE    
  INTEGER linkProbe(1), dte2Dbu1(2), dte2Dbu2(3), channelDbu(4), pvcDbu(5), channelDbu-noProbe(6), pvcDbu-noProbe(7)  

dbuPVCAdd 1.3.6.1.4.1.568.8.7.4
This object allows the user to add a PVC to the existing PVC table, the added PVC must not exist before it is added.
OBJECT-TYPE    
  INTEGER 16..991  

dbuPVCDelete 1.3.6.1.4.1.568.8.7.5
This object allows the user to delete a PVC from the existing PVC table, the PVC must exist before it is deleted.
OBJECT-TYPE    
  INTEGER 16..991  

dbuRecoverCount 1.3.6.1.4.1.568.8.7.6
Number of LMI Active Occurrences to restore PVC change request. The value is between 1 to 20.
OBJECT-TYPE    
  INTEGER 0..10  

dbuDialedIsdnAddress 1.3.6.1.4.1.568.8.7.7
Defines the Dialed ISDN Address for the most recent DBU call
OBJECT-TYPE    
  DisplayString Size(0..26)  

globalStatus 1.3.6.1.4.1.568.8.8.1
Defines device status as: ready = Device is operating normally. connected = At least one PVC is in backup mode. test = Device is in test mode (Not implemented yet). hwFailure = ISDN line is not operable due to a hardware failure.
OBJECT-TYPE    
  INTEGER ready(1), connected(2), test(3), hwFailure(4)  

pvcStatusTable 1.3.6.1.4.1.568.8.8.2
Per PVC status table. The PVCs(DLCIs) monitored are PVCs(DLCIs) defined by LMI messages from the network.
OBJECT-TYPE    
  SEQUENCE OF  
    PvcStatusEntry

pvcStatusEntry 1.3.6.1.4.1.568.8.8.2.1
Identifies an entry (row) in pvcStatusTable.
OBJECT-TYPE    
  PvcStatusEntry  

pvcStatusIndex 1.3.6.1.4.1.568.8.8.2.1.1
Identifies an entry (row) in pvcStatusTable as the local PVC (DLCI) Number.
OBJECT-TYPE    
  INTEGER 16..991  

pvcStatus 1.3.6.1.4.1.568.8.8.2.1.2
Defines the PVC Status as: pvcInactive = Configured at the network, but not active. pvcActive = Configured at the network, and active. pvcConnected = Pvc connected in backup mode. pvcTest = Pvc in test mode (Not yet implemented).
OBJECT-TYPE    
  INTEGER pvcInactive(1), pvcActive(2), pvcConnected(3), pvcTest(4)  

eventSubject 1.3.6.1.4.1.568.8.8.3
Defines CP-3000 Log Events as: device = Device specific events. pvc = PVC specific events.
OBJECT-TYPE    
  INTEGER device(1), pvc(2)  

pvcIdentifier 1.3.6.1.4.1.568.8.8.4
Identifies the PVC Number for PVC specific events only. This objects has no meaning for Device specific events.
OBJECT-TYPE    
  INTEGER 16..991  

cp3000LogCode 1.3.6.1.4.1.568.8.8.5
CP-3000 ASCII Log Code for Device or PVC events
OBJECT-TYPE    
  DisplayString Size(1..1)  

cp3000LogSpeed 1.3.6.1.4.1.568.8.8.6
CP-3000 ASCII Log Code for ISDN Line Speed
OBJECT-TYPE    
  DisplayString Size(1..1)  

cp3000LogDate 1.3.6.1.4.1.568.8.8.7
Date and Time in ASCII format: YYMMDDhhmmss
OBJECT-TYPE    
  DisplayString Size(12..12)  

cp3000LogInfo 1.3.6.1.4.1.568.8.8.8
Need to ask what goes in here
OBJECT-TYPE    
  DisplayString Size(15..15)  

trapAckEnable 1.3.6.1.4.1.568.8.9.1
Acknowledgement setting for CP-3000 Log Event Traps: enabled = NMS has to acknowledge traps received. disabled = NMS doesn't need to acknowledge traps received.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

trapAckTimeout 1.3.6.1.4.1.568.8.9.2
Timeout value to retransmit a trap when trapAckEnable object == enabled and no ACK received from NMS.
OBJECT-TYPE    
  INTEGER 5..120  

trapAckFromMngr 1.3.6.1.4.1.568.8.9.3
Trap Acknowledgement Indication: When trapAckEnable object == enabled NMS has to ACK every trap received.
OBJECT-TYPE    
  INTEGER trapNotAcked(1), trapAcked(2)