Juniper-ROUTER-MIB

File: Juniper-ROUTER-MIB.mib (42698 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
SNMP-FRAMEWORK-MIB Juniper-TC Juniper-IP-POLICY-MIB
Juniper-MIBs

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Unsigned32
Counter32 TEXTUAL-CONVENTION DisplayString
RowStatus TruthValue MODULE-COMPLIANCE
OBJECT-GROUP SnmpEngineID JuniName
JuniIpPolicyName JuniIpPolicyExtendedCommunity juniMibs

Defined Types

JuniNextRouterIndex  
Coordinates routerIndex value allocation for entries in an associated router table. Clients must first read the routerIndex value from this object, then create an entry having the routerIndex value in the associated router table. The DESCRIPTION clause for an object of this type must identify the associated router table. A GET of this object returns the next available routerIndex value to be used to create an entry in the associated router table; or zero, if no valid routerIndex value is available. This object also returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that routerIndex allocation is unintended. Successive GETs will typically return different values, thus avoiding collisions among cooperating management clients seeking to create table entries simultaneously. Unless specified otherwise by its MAX-ACCESS and DESCRIPTION clauses, an object of this type is read-only, and a SET of such an object returns a notWritable error.
TEXTUAL-CONVENTION    
  Unsigned32  

JuniRouterProtocolIndex  
Identifies the router protocol.
TEXTUAL-CONVENTION    
  INTEGER ip(1), osi(2), icmp(3), igmp(4), tcp(5), udp(6), bgp(7), ospf(8), isis(9), rip(10), snmp(11), ntp(12), generator(13), localAddressServer(14), dhcpProxy(15), dhcpRelay(16), nameResolver(17), policyManager(18), sscClient(19), cops(20), mgtm(21), dvmrp(22), pim(23), msdp(24), mpls(25), radius(26), mplsMgr(27), dhcpLocalServer(28), tacacsPlus(29), radiusDisconnect(30), dhcpv6LocalServer(31), radiusProxy(32)  

JuniRouterEntry  
SEQUENCE    
  juniRouterIndex Unsigned32
  juniRouterName JuniName
  juniRouterRowStatus RowStatus
  juniRouterVrf TruthValue
  juniRouterContextName OCTET STRING
  juniRouterContextEngineID SnmpEngineID
  juniRouterSummaryVRFCount Counter32

JuniRouterProtocolEntry  
SEQUENCE    
  juniRouterProtocolRouterIndex Unsigned32
  juniRouterProtocolProtocolIndex JuniRouterProtocolIndex
  juniRouterProtocolRowStatus RowStatus

JuniRouterVrfEntry  
SEQUENCE    
  juniRouterVrfRouterIndex Unsigned32
  juniRouterVrfRouterVrfIndex Unsigned32
  juniRouterVrfIpv4UnicastImportRouteMap JuniIpPolicyName
  juniRouterVrfIpv4UnicastExportRouteMap JuniIpPolicyName
  juniRouterVrfRouteDistinguisher JuniIpPolicyExtendedCommunity
  juniRouterVrfRowStatus RowStatus
  juniRouterVrfRouterName JuniName
  juniRouterVrfRouterDescription DisplayString
  juniRouterVrfIpv4UnicastGlobalExportRouteMap JuniIpPolicyName
  juniRouterVrfIpv4UnicastExportRouteMapFilter TruthValue
  juniRouterVrfIpv6UnicastImportRouteMap JuniIpPolicyName
  juniRouterVrfIpv6UnicastExportRouteMap JuniIpPolicyName
  juniRouterVrfIpv6UnicastGlobalExportRouteMap JuniIpPolicyName
  juniRouterVrfIpv6UnicastExportRouteMapFilter TruthValue
  juniRouterVrfIpv4UnicastGlobalImportRouteMap JuniIpPolicyName
  juniRouterVrfIpv4UnicastGlobalImportMaxRoutes Unsigned32
  juniRouterVrfIpv6UnicastGlobalImportRouteMap JuniIpPolicyName
  juniRouterVrfIpv6UnicastGlobalImportMaxRoutes Unsigned32

JuniRouterVrfRouteTargetEntry  
SEQUENCE    
  juniRouterVrfRouteTargetRouterIndex Unsigned32
  juniRouterVrfRouteTargetRouterVrfIndex Unsigned32
  juniRouterVrfRouteTargetAddrFormat INTEGER
  juniRouterVrfRouteTargetRouteTarget JuniIpPolicyExtendedCommunity
  juniRouterVrfRouteTargetType INTEGER
  juniRouterVrfRouteTargetRowStatus RowStatus

Defined Values

juniRouterMIB 1.3.6.1.4.1.4874.2.2.32
The Router MIB is used to manage the creation and deletion as well as the administrative states of the protocols and functions that run within a designated router.
MODULE-IDENTITY    

juniRouterObjects 1.3.6.1.4.1.4874.2.2.32.1
OBJECT IDENTIFIER    

juniRouterSummaryCounts 1.3.6.1.4.1.4874.2.2.32.1.6
OBJECT IDENTIFIER    

juniRouterSummaryScalars 1.3.6.1.4.1.4874.2.2.32.1.6.1
OBJECT IDENTIFIER    

juniRouterSummaryNonParentVRsConfigured 1.3.6.1.4.1.4874.2.2.32.1.6.1.1
Total number of VRs without VRFs configured.
OBJECT-TYPE    
  Counter32  

juniRouterSummaryParentVRsConfigured 1.3.6.1.4.1.4874.2.2.32.1.6.1.2
Total number of VRs with VRFs configured.
OBJECT-TYPE    
  Counter32  

juniRouterSummaryVRFsConfigured 1.3.6.1.4.1.4874.2.2.32.1.6.1.3
Total number of VRFs configured.
OBJECT-TYPE    
  Counter32  

juniRouterSummaryTotalConfigured 1.3.6.1.4.1.4874.2.2.32.1.6.1.4
Total number of Virtual Routers and VRFs configured.
OBJECT-TYPE    
  Counter32  

juniRouterNextRouterIndex 1.3.6.1.4.1.4874.2.2.32.1.1
Coordinates routerIndex and juniRouterVrfIndex value allocation for entries in the juniRouterTable and juniRouterVrfTable, respectively. A GET of this object returns the next available routerIndex value to be used to create an entry in the associated router table; or zero, if no valid routerIndex value is available. This object also returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that routerIndex allocation is unintended. Successive GETs will typically return different values, thus avoiding collisions among cooperating management clients seeking to create table entries simultaneously.
OBJECT-TYPE    
  JuniNextRouterIndex  

juniRouterTable 1.3.6.1.4.1.4874.2.2.32.1.2
This table contains entries for routers present in the system.
OBJECT-TYPE    
  SEQUENCE OF  
    JuniRouterEntry

juniRouterEntry 1.3.6.1.4.1.4874.2.2.32.1.2.1
Each entry in this table represents a single router. Creating and/or deleting entries in this table causes corresponding entries to be created or deleted in the juniRouterProtocolTable. Note that VRFs also appear as entries in this table and can be differentiated by the juniRouterVrf object. The juniRouterVrfTable shows the parent / child relationship between routers and VRFs present in the system.
OBJECT-TYPE    
  JuniRouterEntry  

juniRouterIndex 1.3.6.1.4.1.4874.2.2.32.1.2.1.1
The routerIndex of this router. When creating entries in this table, suitable values for this object are determined by reading juniRouterNextRouterIndex.
OBJECT-TYPE    
  Unsigned32  

juniRouterName 1.3.6.1.4.1.4874.2.2.32.1.2.1.2
The administratively assigned name given to this router. The name must be unique within the context of this table and cannot be changed after the router instance is created.
OBJECT-TYPE    
  JuniName  

juniRouterRowStatus 1.3.6.1.4.1.4874.2.2.32.1.2.1.3
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: juniRouterRowStatus juniRouterName In addition, when creating an entry the following conditions must hold: A value for juniRouterIndex must have been determined previously by reading juniRouterNextRouterIndex. A corresponding entries in juniRouterProtocolTable are created/destroyed as a result of creating/destroying an entry in this table.
OBJECT-TYPE    
  RowStatus  

juniRouterVrf 1.3.6.1.4.1.4874.2.2.32.1.2.1.4
Identifies whether this router is a VRF or not. A value of true(1) indicates that this is a VRF; a value of false(2) indicates that it is not.
OBJECT-TYPE    
  TruthValue  

juniRouterContextName 1.3.6.1.4.1.4874.2.2.32.1.2.1.5
An internally derived/assigned name given to this router with a specific format: routerN where N is a decimal number (with no leading zeroes) in the range 1..16777215 corresponding to the value of the least significant 24 bits of the juniRouterIndex (the router UID). The name is unique within the context of this table.
OBJECT-TYPE    
  OCTET STRING Size(7..14)  

juniRouterContextEngineID 1.3.6.1.4.1.4874.2.2.32.1.2.1.6
The virtual router SNMP engine's administratively-unique identifier. This is used as the contextEngineId to reach the virtual router's SNMP context via the system-wide SNMP engine using SNMPv3.
OBJECT-TYPE    
  SnmpEngineID  

juniRouterSummaryVRFCount 1.3.6.1.4.1.4874.2.2.32.1.2.1.7
The number of VRFs contained in the VR.
OBJECT-TYPE    
  Counter32  

juniRouterProtocolTable 1.3.6.1.4.1.4874.2.2.32.1.3
This table contains entries for each protocol supported by the router entry created in the juniRouterTable.
OBJECT-TYPE    
  SEQUENCE OF  
    JuniRouterProtocolEntry

juniRouterProtocolEntry 1.3.6.1.4.1.4874.2.2.32.1.3.1
Each entry provides administrative control on a router protocol for the router designated by the first indice to this table. The second indice identifies the router protocol. Entries in this table are created as a side-effect of row creation in the juniRouterTable or juniRouterVrfTable.
OBJECT-TYPE    
  JuniRouterProtocolEntry  

juniRouterProtocolRouterIndex 1.3.6.1.4.1.4874.2.2.32.1.3.1.1
The routerIndex of this router. This object is the same as the juniRouterIndex object defined in the juniRouterTable.
OBJECT-TYPE    
  Unsigned32  

juniRouterProtocolProtocolIndex 1.3.6.1.4.1.4874.2.2.32.1.3.1.2
Identities the router protocol.
OBJECT-TYPE    
  JuniRouterProtocolIndex  

juniRouterProtocolRowStatus 1.3.6.1.4.1.4874.2.2.32.1.3.1.3
Administrative control and status of a protocol on a router. The following values can be read from this object: active(1) - Indicates that the protocol on the designated router is created, configured, and running. notReady(3) - Indicates that the protocol requires additional configuration in a protocol specific MIB module. Examples include the BGP and OSPF protocols, which require additional configuration of protocol specific parameters such as: Autonomous System (AS) for BGP, and Process Id for OSPF. destroy(6) - The destroy(3) operation can fail if there are executing applications dependent on the protocol. If an attempt is made to destroy(6) an active(1) protocol that other applications are dependent on, the rowStatus will read destroy(6). Normally, when a row is destroyed, the agent will cleaup and remove the entry. The following values can be written to this object: active(1) - Activate protocol on the designated router. createAndGo(4) - Create protocol on designated router. The router indicated by juniRouterProtocolRouterIndex must already exist in the juniRouterTable. The value of the juniRouterProtocolProtocolIndex must be from the set of protocol values defined by the JuniRouterProtocolIndex type. destroy(6) - Destroy protocol on designated router. If the operation is successful, the agent will remove the entry. If the operation failed, the row will remain in the table with a rowStatus value of destroy(6). Conditions on destroy(6): 1) The default router can not be deleted. 2) The local router can not be deleted. A local router is defined as the router that sourced the SNMP request. Upon creation of a router in the juniRouterTable, some protocol entries will appear in this table by default, which indicates that these protocols are created by the action of creating a router. It is important to note, that this behavior may change over time by protocol type.
OBJECT-TYPE    
  RowStatus  

juniRouterVrfTable 1.3.6.1.4.1.4874.2.2.32.1.4
This table contains entries for each VRF on each router entry created in the juniRouterTable.
OBJECT-TYPE    
  SEQUENCE OF  
    JuniRouterVrfEntry

juniRouterVrfEntry 1.3.6.1.4.1.4874.2.2.32.1.4.1
Each entry provides administrative control on a router VRF for the router designated by the first indice of this table. The second indice identifies the router VRF. The parent router must exist in the juniRouterTable before performing VRF row creation in this table
OBJECT-TYPE    
  JuniRouterVrfEntry  

juniRouterVrfRouterIndex 1.3.6.1.4.1.4874.2.2.32.1.4.1.1
The router index of this router, also referred to as the parent of the VRF. This object is the same as the juniRouterIndex object defined in the juniRouterTable.
OBJECT-TYPE    
  Unsigned32  

juniRouterVrfRouterVrfIndex 1.3.6.1.4.1.4874.2.2.32.1.4.1.2
The VRF router index for this entry, also referred as the child of the parent router, which is identified by the first indice to this table.
OBJECT-TYPE    
  Unsigned32  

juniRouterVrfIpv4UnicastImportRouteMap 1.3.6.1.4.1.4874.2.2.32.1.4.1.3
The VRF router import route map for IPv4 unicast routes.
OBJECT-TYPE    
  JuniIpPolicyName  

juniRouterVrfIpv4UnicastExportRouteMap 1.3.6.1.4.1.4874.2.2.32.1.4.1.4
The VRF router export route map for IPv4 unicast routes.
OBJECT-TYPE    
  JuniIpPolicyName  

juniRouterVrfRouteDistinguisher 1.3.6.1.4.1.4874.2.2.32.1.4.1.5
The VRF router route distinguisher.
OBJECT-TYPE    
  JuniIpPolicyExtendedCommunity  

juniRouterVrfRowStatus 1.3.6.1.4.1.4874.2.2.32.1.4.1.7
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy *** LIMITED CONFIGURATION LEVEL *** RowStatus createAndGo/destroy operations have the following special-purpose semantics: createAndGo Create an entry having the specified configuration and append it to the target list, i.e. create an juniRouterVrfEntry table entry with the associated characteristics. destroy Destroy the specified element. Entries in this table can be modified once the row has been created. To create an entry in this table, the following entry objects MUST be explicitly configured: A value for juniRouterVrfRouterIndex must have been determined previously by reading juniRouterNextRouterIndex. A parent router must exist in the juniRouterTable.
OBJECT-TYPE    
  RowStatus  

juniRouterVrfRouterName 1.3.6.1.4.1.4874.2.2.32.1.4.1.8
The administratively assigned name given to this VRF router. The name must be unique within the context of this table and cannot be changed after the router instance is created.
OBJECT-TYPE    
  JuniName  

juniRouterVrfRouterDescription 1.3.6.1.4.1.4874.2.2.32.1.4.1.9
The administratively assigned description given to this VRF router.
OBJECT-TYPE    
  DisplayString Size(0..80)  

juniRouterVrfIpv4UnicastGlobalExportRouteMap 1.3.6.1.4.1.4874.2.2.32.1.4.1.10
The VRF router global export route map for IPv4 unicast routes.
OBJECT-TYPE    
  JuniIpPolicyName  

juniRouterVrfIpv4UnicastExportRouteMapFilter 1.3.6.1.4.1.4874.2.2.32.1.4.1.11
Is the VRF export map for IPv4 unicast routes allowed to filter routes?
OBJECT-TYPE    
  TruthValue  

juniRouterVrfIpv6UnicastImportRouteMap 1.3.6.1.4.1.4874.2.2.32.1.4.1.12
The VRF router import route map for IPv6 unicast routes.
OBJECT-TYPE    
  JuniIpPolicyName  

juniRouterVrfIpv6UnicastExportRouteMap 1.3.6.1.4.1.4874.2.2.32.1.4.1.13
The VRF router export route map for IPv6 unicast routes.
OBJECT-TYPE    
  JuniIpPolicyName  

juniRouterVrfIpv6UnicastGlobalExportRouteMap 1.3.6.1.4.1.4874.2.2.32.1.4.1.14
The VRF router global export route map for IPv6 unicast routes.
OBJECT-TYPE    
  JuniIpPolicyName  

juniRouterVrfIpv6UnicastExportRouteMapFilter 1.3.6.1.4.1.4874.2.2.32.1.4.1.15
Is the VRF export map for IPv6 unicast routes allowed to filter routes?
OBJECT-TYPE    
  TruthValue  

juniRouterVrfIpv4UnicastGlobalImportRouteMap 1.3.6.1.4.1.4874.2.2.32.1.4.1.16
The VRF router global import route map for IPv4 unicast routes.
OBJECT-TYPE    
  JuniIpPolicyName  

juniRouterVrfIpv4UnicastGlobalImportMaxRoutes 1.3.6.1.4.1.4874.2.2.32.1.4.1.17
The maximum number of IPv4 unicast routes which can be globaly imported.
OBJECT-TYPE    
  Unsigned32  

juniRouterVrfIpv6UnicastGlobalImportRouteMap 1.3.6.1.4.1.4874.2.2.32.1.4.1.18
The VRF router global import route map for IPv6 unicast routes.
OBJECT-TYPE    
  JuniIpPolicyName  

juniRouterVrfIpv6UnicastGlobalImportMaxRoutes 1.3.6.1.4.1.4874.2.2.32.1.4.1.19
The maximum number of IPv6 unicast routes which can be globaly imported.
OBJECT-TYPE    
  Unsigned32  

juniRouterVrfRouteTargetTable 1.3.6.1.4.1.4874.2.2.32.1.5
This table contains entries for each route target for the router/VRF entry created in the juniRouterTable and juniRouterVrfTable.
OBJECT-TYPE    
  SEQUENCE OF  
    JuniRouterVrfRouteTargetEntry

juniRouterVrfRouteTargetEntry 1.3.6.1.4.1.4874.2.2.32.1.5.1
Each entry provides administrative control on VRF route targets for the router/VRF pair designated by the first and second indice of this table. The third indice identifies the route target. The parent router must exist in the juniRouterTable and the VRF router must exist in the juniRouterVrfTable before performing creation of the route target in this table.
OBJECT-TYPE    
  JuniRouterVrfRouteTargetEntry  

juniRouterVrfRouteTargetRouterIndex 1.3.6.1.4.1.4874.2.2.32.1.5.1.1
The routerIndex of this router, also referred to as the parent of the VRF. This object is the same as the juniRouterIndex object defined in the juniRouterTable.
OBJECT-TYPE    
  Unsigned32  

juniRouterVrfRouteTargetRouterVrfIndex 1.3.6.1.4.1.4874.2.2.32.1.5.1.2
The VRF router index for this entry, also referred as the child of the parent router, which is identified by the first indice to this table.
OBJECT-TYPE    
  Unsigned32  

juniRouterVrfRouteTargetAddrFormat 1.3.6.1.4.1.4874.2.2.32.1.5.1.3
The address format of the route target.
OBJECT-TYPE    
  INTEGER routeTargetFormatAsn(0), routeTargetFormateIp(1)  

juniRouterVrfRouteTargetRouteTarget 1.3.6.1.4.1.4874.2.2.32.1.5.1.4
The VRF router route target.
OBJECT-TYPE    
  JuniIpPolicyExtendedCommunity  

juniRouterVrfRouteTargetType 1.3.6.1.4.1.4874.2.2.32.1.5.1.5
The VRF router route target type.
OBJECT-TYPE    
  INTEGER routeTargetInvalid(0), routeTargetImport(1), routeTargetExport(2), routeTargetBoth(3)  

juniRouterVrfRouteTargetRowStatus 1.3.6.1.4.1.4874.2.2.32.1.5.1.6
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy *** LIMITED CONFIGURATION LEVEL *** RowStatus createAndGo/destroy operations have the following special-purpose semantics: createAndGo Create an entry having the specified configuration and append it to the target list, i.e., create an juniRouterVrfRouteTargetEntry table entry with the associated characteristics. destroy Destroy the specified element. To create an entry in this table, the following entry objects MUST be explicitly configured: A parent router must exist in the juniRouterTable. A VRF router must exist in the juniRouterVrfTable.
OBJECT-TYPE    
  RowStatus  

juniRouterConformance 1.3.6.1.4.1.4874.2.2.32.4
OBJECT IDENTIFIER    

juniRouterCompliances 1.3.6.1.4.1.4874.2.2.32.4.1
OBJECT IDENTIFIER    

juniRouterGroups 1.3.6.1.4.1.4874.2.2.32.4.2
OBJECT IDENTIFIER    

juniRouterCompliance 1.3.6.1.4.1.4874.2.2.32.4.1.1
An obsolete compliance statement for entities which implement the Juniper Router MIB. This statement became obsolete when support was added for VRFs within routers.
MODULE-COMPLIANCE    

juniRouterCompliance2 1.3.6.1.4.1.4874.2.2.32.4.1.2
An obsolete compliance statement for entities which implement the Juniper Router MIB. This statement became obsolete when support was added for the router context name.
MODULE-COMPLIANCE    

juniRouterCompliance3 1.3.6.1.4.1.4874.2.2.32.4.1.3
Obsolete compliance statement for entities which implement the Juniper Router MIB. This statement became obsolete when support was added for the router context engine ID.
MODULE-COMPLIANCE    

juniRouterCompliance4 1.3.6.1.4.1.4874.2.2.32.4.1.4
Obsolete compliance statement for entities which implement the Juniper Router MIB. This statement became obsolete when the global export map and the export map filter option were added to the VRF group.
MODULE-COMPLIANCE    

juniRouterCompliance5 1.3.6.1.4.1.4874.2.2.32.4.1.5
Obsolete compliance statement for entities which implement the Juniper Router MIB.
MODULE-COMPLIANCE    

juniRouterCompliance6 1.3.6.1.4.1.4874.2.2.32.4.1.7
Obsolete compliance statement for entities which implement the Juniper Router MIB.
MODULE-COMPLIANCE    

juniRouterCompliance7 1.3.6.1.4.1.4874.2.2.32.4.1.8
The compliance statement for entities which implement the Juniper Router MIB.
MODULE-COMPLIANCE    

juniRouterGroup 1.3.6.1.4.1.4874.2.2.32.4.2.1
An obsolete collection of objects providing management of routers and routing protocols in a Juniper product. This group became obsolete when support was added for VRFs within routers.
OBJECT-GROUP    

juniRouterGroup2 1.3.6.1.4.1.4874.2.2.32.4.2.2
An obsolete collection of objects providing management of routers and routing protocols in a Juniper product. This group became obsolete when support was added for the router context name.
OBJECT-GROUP    

juniRouterVrfGroup 1.3.6.1.4.1.4874.2.2.32.4.2.3
Obsolete collection of objects providing management of VRFs within routers in a Juniper product. This group became obsolete when the VRF router description object was added.
OBJECT-GROUP    

juniRouterGroup3 1.3.6.1.4.1.4874.2.2.32.4.2.4
Obsolete collection of objects providing management of routers and routing protocols in a Juniper product. This group became obsolete when the contect engine ID object was added.
OBJECT-GROUP    

juniRouterVrfGroup2 1.3.6.1.4.1.4874.2.2.32.4.2.5
Obsolete collection of objects providing management of VRFs within routers in a Juniper product. This group became obsolete when the global export map and the export map filter option were added.
OBJECT-GROUP    

juniRouterGroup4 1.3.6.1.4.1.4874.2.2.32.4.2.6
Obsolete collection of objects providing management of routers and routing protocols in a Juniper product. This group became obsolete when the summaryVRfCount object was added.
OBJECT-GROUP    

juniRouterVrfGroup3 1.3.6.1.4.1.4874.2.2.32.4.2.7
Obsolete collection of objects providing management of VRFs within routers in a Juniper product. This group became obsolete when the global import map was added and when support for separate ipv4 and ipv6 route maps was added.
OBJECT-GROUP    

juniRouterGroup5 1.3.6.1.4.1.4874.2.2.32.4.2.8
A collection of objects providing management of routers and routing protocols in a Juniper product.
OBJECT-GROUP    

juniRouterSummaryScalarsGroup 1.3.6.1.4.1.4874.2.2.32.4.2.9
A collection of objects providing summary counts for number of virtual routers and virtual router forwarding instances (VRFs) in a Juniper product.
OBJECT-GROUP    

juniRouterVrfGroup4 1.3.6.1.4.1.4874.2.2.32.4.2.10
A collection of objects providing management of VRFs within routers in a Juniper product.
OBJECT-GROUP