Jetnet4508V2

File: Jetnet4508V2.mib (249068 bytes)

Imported modules

RFC1155-SMI SNMPv2-TC Q-BRIDGE-MIB

Imported symbols

Integer32 IpAddress OBJECT-TYPE
internet RowStatus DisplayString
MacAddress TimeInterval PortList

Defined Types

AlertType  
Tok_String
TEXTUAL-CONVENTION    
  INTEGER enable(1), disable(2)  

IPconfigurationEntry  
SEQUENCE    
  ipConfigurationIndex INTEGER
  ipConfigurationDHCPStatus INTEGER
  ipConfigurationAddress IpAddress
  ipConfigurationSubMask IpAddress
  ipConfigurationGateway IpAddress
  ipConfigurationDNS1 IpAddress
  ipConfigurationDNS2 IpAddress
  ipConfigurationStatus INTEGER

NtpEntry  
SEQUENCE    
  ntpIndex Integer32
  ntpServerIP IpAddress

DhcpServerPoolEntry  
SEQUENCE    
  dhcpServerPoolIndex Integer32
  dhcpServerPoolName DisplayString
  dhcpServerPoolNetwork IpAddress
  dhcpServerPoolSubMask IpAddress
  dhcpServerPoolGateway IpAddress
  dhcpServerPoolLeaseTime Integer32
  dhcpServerPoolStatus RowStatus

DhcpExcludedEntry  
SEQUENCE    
  dhcpExcludedIndex Integer32
  dhcpExcludedIp IpAddress
  dhcpExcludedStatus RowStatus

DhcpManualBindingEntry  
SEQUENCE    
  dhcpManualBindingIndex Integer32
  dhcpManualBindingIp IpAddress
  dhcpManualBindingMac MacAddress
  dhcpManualBindingStatus RowStatus

DhcpStaticPortEntry  
SEQUENCE    
  dhcpStaticPortIndex Integer32
  dhcpStaticPortNumber INTEGER
  dhcpStaticPortIp IpAddress
  dhcpStaticPortStatus RowStatus

DhcpOption82Entry  
SEQUENCE    
  dhcpOption82Index Integer32
  dhcpOption82CircuitIdType INTEGER
  dhcpOption82CircuitIdValue OCTET STRING
  dhcpOption82RemoteIdType INTEGER
  dhcpOption82RemoteIdValue OCTET STRING
  dhcpOption82Ip IpAddress
  dhcpOption82Status RowStatus

DhcpServerLeasedEntry  
SEQUENCE    
  dhcpServerLeasedIndex Integer32
  dhcpServerLeasedIp IpAddress
  dhcpServerLeasedMac MacAddress
  dhcpServerLeasedType INTEGER
  dhcpServerLeasedTime Integer32

DhcpRelayAgentCircuitIdEntry  
SEQUENCE    
  dhcpRelayAgentCircuitIdPortNum Integer32
  dhcpRelayAgentCircuitIdType Integer32
  dhcpRelayAgentCircuitIdValue OCTET STRING
  dhcpRelayAgentCircuitIdDisplay OCTET STRING

DhcpHelperAddressEntry  
SEQUENCE    
  dhcpHelperAddress IpAddress

PortCtrlEntry  
SEQUENCE    
  portCtrlIndex INTEGER
  portCtrlPortName DisplayString
  portCtrlPortStatus INTEGER
  portCtrlSpeedAndDuplex INTEGER
  portCtrlFlowControl INTEGER
  portCtrlPortDescription DisplayString

PortStatusEntry  
SEQUENCE    
  portStatusIndex Integer32
  portStatusType INTEGER
  portStatusLink INTEGER
  portStatusState INTEGER
  portStatusSpeedDuplex INTEGER
  portStatusFlowCtrl INTEGER
  sfpVender DisplayString
  sfpWavelength Integer32
  sfpDistance Integer32

RateLimitingEntry  
SEQUENCE    
  rateLimitingPortNum Integer32
  rateLimitingIngressLimitType INTEGER
  rateLimitingIngressRate Integer32
  rateLimitingEgressRate Integer32

PortTrunkAggregatorSettingEntry  
SEQUENCE    
  portTrunkPortIndex INTEGER
  portTrunkAggregatorGroupId INTEGER
  portTrunkAggregatorType INTEGER

PortTrunkAggregatorStatusEntry  
SEQUENCE    
  portTrunkAggregatorGroupIndex INTEGER
  portTrunkAggregatorGroupType INTEGER
  portTrunkAggregatorGroupMember PortList
  portTrunkAggregatorIndividual PortList
  portTrunkAggregatorLinkDown PortList

MultipleSuperRingConfigEntry  
SEQUENCE    
  superRingConfigId INTEGER
  superRingStatus RowStatus
  superRingName DisplayString
  superRingConfigVersion INTEGER
  superRingDevicePriority INTEGER
  superRingRingPort1 INTEGER
  superRingRingPort2 INTEGER
  superRingRingPort1PathCost INTEGER
  superRingRingPort2PathCost INTEGER
  superRingRapidDualHomingStatus INTEGER

MultipleSuperRingStatusEntry  
SEQUENCE    
  superRingStatusId INTEGER
  superRingVersion INTEGER
  superRingDeviceRole INTEGER
  superRingRingPortList1 PortList
  superRingRingPortList2 PortList
  superRingRingStatus INTEGER
  superRingRmMac MacAddress
  superRingBlockedPort PortList
  superRingRoleTransitionCount Integer32
  superRingRingStateTransitionCount Integer32

RstpPerPortCfgEntry  
SEQUENCE    
  rstpPerPortCfgPortNum Integer32
  rstpPerPortCfgPathCost Integer32
  rstpPerPortCfgPriority Integer32
  rstpPerPortCfgAdminP2P INTEGER
  rstpPerPortCfgAdminEdge INTEGER

RstpRootBridgeInformationEntry  
SEQUENCE    
  rstpRootBridgeInformationIndex Integer32
  rstpRootBridgeInformationBridgeID DisplayString
  rstpRootBridgeInformationRootPriority Integer32
  rstpRootBridgeInformationRootPort DisplayString
  rstpRootBridgeInformationRootPathCost Integer32
  rstpRootBridgeInformationMaxAge Integer32
  rstpRootBridgeInformationHelloTime Integer32
  rstpRootBridgeInformationForwardDelay Integer32

RstpPerPortInfoEntry  
SEQUENCE    
  rstpPerPortInfoPortNum Integer32
  rstpPerPortInfoPathCost Integer32
  rstpPerPortInfoPriority Integer32
  rstpPerPortInfoAdminP2P INTEGER
  rstpPerPortInfoAdminEdge INTEGER
  rstpPerPortInfoState INTEGER
  rstpPerPortInfoRole INTEGER
  rstpPerPortInfoAggregated DisplayString

MstpPerInstCfgEntry  
SEQUENCE    
  mstpPerInstCfgInstanceID Integer32
  mstpPerInstCfgVlanGroup DisplayString
  mstpPerInstCfgInstancePriority Integer32
  mstpPerInstCfgStatus RowStatus

MstpPerPortCfgEntry  
SEQUENCE    
  mstpPerPortCfgIndex Integer32
  mstpPerPortCfgInstanceID Integer32
  mstpPerPortCfgPortNum Integer32
  mstpPerPortCfgPathCost Integer32
  mstpPerPortCfgPriority Integer32
  mstpPerPortCfgLinkType INTEGER
  mstpPerPortCfgEdgePort INTEGER

MstpRootInformationEntry  
SEQUENCE    
  mstpRootInformationInstanceID Integer32
  mstpRootInformationRootAddress DisplayString
  mstpRootInformationRootPriority Integer32
  mstpRootInformationRootPort DisplayString
  mstpRootInformationRootPathCost Integer32
  mstpRootInformationMaxAge Integer32
  mstpRootInformationHelloTime Integer32
  mstpRootInformationForwardDelay Integer32

MstpPerPortInfoEntry  
SEQUENCE    
  mstpPerPortInfoIndex Integer32
  mstpPerPortInfoInstanceID Integer32
  mstpPerPortInfoPortNum Integer32
  mstpPerPortInfoRole INTEGER
  mstpPerPortInfoState INTEGER
  mstpPerPortInfoPathCost Integer32
  mstpPerPortInfoPriority Integer32
  mstpPerPortInfoLinkType INTEGER
  mstpPerPortInfoEdgePort INTEGER

Dot1qPortVlanEntry  
SEQUENCE    
  dot1qPortIndex INTEGER
  dot1qPvid INTEGER
  dot1qPortAcceptableFrameTypes INTEGER
  dot1qPortIngressFiltering INTEGER

Dot1qVlanStaticEntry  
SEQUENCE    
  dot1qVlanIndex INTEGER
  dot1qVlanStaticName DisplayString
  dot1qVlanStaticEgressPorts PortList
  dot1qVlanStaticUntaggedPorts PortList
  dot1qVlanStaticTaggedPorts PortList
  dot1qVlanStaticRowStatus RowStatus

Dot1qPortGvrpEntry  
SEQUENCE    
  dot1qPortGvrpIndex INTEGER
  dot1qPortGvrpStatus INTEGER
  dot1qPortGvrpRegistrationMode INTEGER
  dot1qPortGarpJoinTimer TimeInterval
  dot1qPortGarpLeaveTimer TimeInterval
  dot1qPortGarpLeaveAllTimer TimeInterval

Dot1qVlanCurrentEntry  
SEQUENCE    
  dot1qVlanCurrentIndex INTEGER
  dot1qVlanCurrentEgressPorts PortList
  dot1qVlanCurrentUntaggedPorts PortList
  dot1qVlanStatus INTEGER

Dot1qTunnelPortEntry  
SEQUENCE    
  dot1qTunnelPortIndex INTEGER
  dot1qTunnelPortMode INTEGER

PrivateVlanIdEntry  
SEQUENCE    
  privateVlanId INTEGER
  privateVlanIdType INTEGER

PrivateVlanPortEntry  
SEQUENCE    
  privateVlanPortIndex INTEGER
  privateVlanPortMode INTEGER

PrivateVlanHostAssociationEntry  
SEQUENCE    
  privateVlanHostAssociationPortIndex INTEGER
  privateVlanHostAssociationPrimaryVid INTEGER
  privateVlanHostAssociationSecondaryVid INTEGER

PrivateVlanMappingEntry  
SEQUENCE    
  privateVlanMappingPromiscuousPortIndex INTEGER
  privateVlanMappingPrimaryVid INTEGER
  privateVlanMappingSecondaryVidList DisplayString

QosPortDefaultCosEntry  
SEQUENCE    
  qosPortNum Integer32
  qosPortTrust Integer32
  qosPortDefaultCos Integer32

QosCOSEntry  
SEQUENCE    
  qosCOSPriority Integer32
  qosCOS INTEGER

QosDscpEntry  
SEQUENCE    
  qosDscpPriority Integer32
  qosDscp INTEGER

IgmpSnoopingEntry  
SEQUENCE    
  igmpSnoopingEntryVID INTEGER
  igmpSnoopingEntryStatus INTEGER

IgmpSnoopingGroupEntry  
SEQUENCE    
  igmpSnoopingGroupEntryVID INTEGER
  igmpSnoopingGroupEntryIPAddr IpAddress
  igmpSnoopingGroupEntryMembers PortList

Dot1dPortGmrpEntry  
SEQUENCE    
  dot1dPortGmrpIndex INTEGER
  dot1dPortGmrpStatus INTEGER

SnmpCommunityStringEntry  
SEQUENCE    
  snmpCommunityStringIndex Integer32
  snmpCommunityStringName DisplayString
  snmpCommunityStringPrivilege INTEGER
  snmpCommunityStringStatus INTEGER

SnmpV3UserEntry  
SEQUENCE    
  snmpV3UserIndex Integer32
  snmpV3UserName DisplayString
  snmpV3UserSecurityLevel INTEGER
  snmpV3UserAuthProtocol INTEGER
  snmpV3UserAuthPassword DisplayString
  snmpV3UserDesPassword DisplayString
  snmpV3UserStatus RowStatus

SnmpTrapServerEntry  
SEQUENCE    
  snmpTrapServerIndex Integer32
  snmpTrapServerIPAddr IpAddress
  snmpTrapServerTrapComm DisplayString
  snmpTrapServerTrapVer INTEGER
  snmpTrapServerStatus RowStatus

PortSecurityStatusEntry  
SEQUENCE    
  portSecurityPortIndex Integer32
  portSecurityPortStatus INTEGER

PortSecurityMacEntry  
SEQUENCE    
  portSecurityMacIndex Integer32
  portSecurityPort Integer32
  portSecurityVlanIndex Integer32
  portSecurityMac MacAddress
  portSecurityMacStatus RowStatus

IpSecurityEntry  
SEQUENCE    
  ipSecurityIndex Integer32
  ipSecurityIP IpAddress
  ipSecurityRowStatus RowStatus

RadiusServerEntry  
SEQUENCE    
  radiusServerIndex Integer32
  radiusServerIp IpAddress
  radiusServerServerPort Integer32
  radiusServerAccountingPort Integer32
  radiusServerSharedKey DisplayString

Dot1xLocalUserEntry  
SEQUENCE    
  dot1xLocalUserIndex Integer32
  dot1xLocalUserName DisplayString
  dot1xLocalUserPassword DisplayString
  dot1xLocalUserVid Integer32

Dot1xPortConfigEntry  
SEQUENCE    
  dot1xPortConfigIndex Integer32
  dot1xPortAuthControl INTEGER
  dot1xPortReauthentication INTEGER
  dot1xPortMaxRequest INTEGER
  dot1xPortGuestVlan INTEGER
  dot1xPortHostMode INTEGER
  dot1xPortAdminDirection INTEGER
  dot1xPortConfigSetDefault INTEGER
  dot1xPortReinitialize INTEGER
  dot1xPortClientReauth INTEGER

Dot1xPortTimeoutConfigEntry  
SEQUENCE    
  dot1xPortTimeoutIndex Integer32
  dot1xPortReauthPeriod Integer32
  dot1xPortQuietPeriod Integer32
  dot1xPortTxPeriod Integer32
  dot1xPortSupplicantTimeout Integer32
  dot1xPortServerTimeout Integer32

Dot1xPortStatusEntry  
SEQUENCE    
  dot1xPortStatusIndex Integer32
  dot1xPortCtrl INTEGER
  dot1xPortAuthStatus INTEGER
  dot1xPortAuthSupplicant MacAddress
  dot1xPortOperDirection INTEGER

FaultRelayEntry  
SEQUENCE    
  faultRelayId INTEGER
  diConfig INTEGER
  dryOutputConfig INTEGER
  dryOutputOnPeriod INTEGER
  dryOutputOffPeriod INTEGER
  powerFailureConfig INTEGER
  linkFailureConfig PortList
  pingFailureConfig INTEGER
  pingFailureIP IpAddress
  pingFailureResetTime INTEGER
  pingFailureHoldTime INTEGER
  ringFailureConfig INTEGER

SystemEventEntry  
SEQUENCE    
  eventSystemEventIndex Integer32
  eventDeviceColdStartEvent AlertType
  eventDeviceWarmStartEvent AlertType
  eventAuthenticationFailureEvent AlertType
  eventRingEvent AlertType
  eventPower1FailureEvent AlertType
  eventPower2FailureEvent AlertType
  eventFaultRelayEvent AlertType
  eventTimeSynchronizeEvent AlertType
  eventDI1ChangeEvent AlertType
  eventLoopDetectionEvent AlertType

PortEventEntry  
SEQUENCE    
  eventPortNumber Integer32
  eventPortEvent INTEGER

EmailAlertRcptEntry  
SEQUENCE    
  eventEmailAlertRcptIndex Integer32
  eventEmailAlertRcptEmailAddr DisplayString

MACAddrEntry  
SEQUENCE    
  macAddressAddr MacAddress
  macAddressType INTEGER
  macAddressPortList PortList
  macAddressVlanId Integer32
  macAddressStatus INTEGER

SwitchPortStatEntry  
SEQUENCE    
  swPortStatIndex Integer32
  swPortStatType INTEGER
  swPortStatLink INTEGER
  swPortStatState INTEGER
  swPortStatRXGoodPkt Integer32
  swPortStatRXBadPkt Integer32
  swPortStatRXAbortPkt Integer32
  swPortStatTXGoodPkt Integer32
  swPortStatTXBadPkt Integer32
  swPortStatPacketCollision Integer32

PortMirrorSourceEntry  
SEQUENCE    
  portMirrorPortNum Integer32
  portMirrorSourcePort INTEGER

EventLogEntry  
SEQUENCE    
  eventLogIndex Integer32
  eventLogDescription DisplayString

LldpNeighborEntry  
SEQUENCE    
  lldpNeighborLocalPort DisplayString
  lldpNeighborMacAddress MacAddress
  lldpNeighborIpAddress IpAddress
  lldpNeighborVID INTEGER
  lldpNeighborTTL INTEGER

Defined Values

private 1.3.6.1.4
OBJECT IDENTIFIER    

enterprises 1.3.6.1.4.1
OBJECT IDENTIFIER    

korenix 1.3.6.1.4.1.24062
OBJECT IDENTIFIER    

products 1.3.6.1.4.1.24062.2
OBJECT IDENTIFIER    

managedFESwitch 1.3.6.1.4.1.24062.2.2
OBJECT IDENTIFIER    

jetnet4508V2 1.3.6.1.4.1.24062.2.2.17
OBJECT IDENTIFIER    

contact 1.3.6.1.4.1.24062.1
The MIB module for Korenix Industrial Web-Managed Ethernet Rail Switch
MODULE-IDENTITY    

systemInfo 1.3.6.1.4.1.24062.2.2.17.1
OBJECT IDENTIFIER    

basicSetting 1.3.6.1.4.1.24062.2.2.17.2
OBJECT IDENTIFIER    

portConfiguration 1.3.6.1.4.1.24062.2.2.17.3
OBJECT IDENTIFIER    

networkRedundancy 1.3.6.1.4.1.24062.2.2.17.4
OBJECT IDENTIFIER    

vlan 1.3.6.1.4.1.24062.2.2.17.5
OBJECT IDENTIFIER    

trafficPrioritization 1.3.6.1.4.1.24062.2.2.17.6
OBJECT IDENTIFIER    

multicastFiltering 1.3.6.1.4.1.24062.2.2.17.7
OBJECT IDENTIFIER    

snmp 1.3.6.1.4.1.24062.2.2.17.8
OBJECT IDENTIFIER    

security 1.3.6.1.4.1.24062.2.2.17.9
OBJECT IDENTIFIER    

warning 1.3.6.1.4.1.24062.2.2.17.10
OBJECT IDENTIFIER    

monitorandDiag 1.3.6.1.4.1.24062.2.2.17.11
OBJECT IDENTIFIER    

save 1.3.6.1.4.1.24062.2.2.17.12
OBJECT IDENTIFIER    

systemName 1.3.6.1.4.1.24062.2.2.17.1.1
An administratively-assigned name for this managed node. By convention, this is the node's fully-qualified domain name.
OBJECT-TYPE    
  DisplayString Size(0..255)  

systemLocation 1.3.6.1.4.1.24062.2.2.17.1.2
The physical location of this node (e.g., telephone closet, 3rd floor').
OBJECT-TYPE    
  DisplayString Size(0..255)  

systemContact 1.3.6.1.4.1.24062.2.2.17.1.3
The textual identification of the contact person for this managed node, together with information on how to contact this person.
OBJECT-TYPE    
  DisplayString Size(0..255)  

systemDescr 1.3.6.1.4.1.24062.2.2.17.1.4
A textual description of the entity. This value should include the full name and version identification of the system's hardware type, software operating-system, and networking software. It is mandatory that this only contain printable ASCII characters.
OBJECT-TYPE    
  DisplayString Size(0..255)  

systemFwVer 1.3.6.1.4.1.24062.2.2.17.1.5
Firmware version of the device.
OBJECT-TYPE    
  DisplayString Size(0..20)  

systemMacAddress 1.3.6.1.4.1.24062.2.2.17.1.6
The MAC address of this device. An Media Access Control address (MAC address) is a unique identifier attached to most network adapters (NICs). It is a number that acts like a name for a particular network adapter
OBJECT-TYPE    
  MacAddress  

systemProductName 1.3.6.1.4.1.24062.2.2.17.1.7
Tok_String
OBJECT-TYPE    
  DisplayString Size(0..255)  

systemSerialNumber 1.3.6.1.4.1.24062.2.2.17.1.8
Tok_String
OBJECT-TYPE    
  DisplayString Size(0..255)  

systemManufacturingDate 1.3.6.1.4.1.24062.2.2.17.1.9
Tok_String
OBJECT-TYPE    
  DisplayString Size(0..255)  

switchSetting 1.3.6.1.4.1.24062.2.2.17.2.1
OBJECT IDENTIFIER    

adminPassword 1.3.6.1.4.1.24062.2.2.17.2.2
OBJECT IDENTIFIER    

ipConfiguration 1.3.6.1.4.1.24062.2.2.17.2.3
OBJECT IDENTIFIER    

timeSetting 1.3.6.1.4.1.24062.2.2.17.2.4
OBJECT IDENTIFIER    

dhcpServer 1.3.6.1.4.1.24062.2.2.17.2.5
OBJECT IDENTIFIER    

backupAndRestore 1.3.6.1.4.1.24062.2.2.17.2.6
OBJECT IDENTIFIER    

tftpUpgrade 1.3.6.1.4.1.24062.2.2.17.2.7
OBJECT IDENTIFIER    

factoryDefault 1.3.6.1.4.1.24062.2.2.17.2.8
OBJECT IDENTIFIER    

systemReboot 1.3.6.1.4.1.24062.2.2.17.2.9
OBJECT IDENTIFIER    

switchSettingSystemName 1.3.6.1.4.1.24062.2.2.17.2.1.1
An administratively-assigned name for this managed node. By convention, this is the node's fully-qualified domain name.
OBJECT-TYPE    
  DisplayString Size(1..256)  

switchSettingSystemLocation 1.3.6.1.4.1.24062.2.2.17.2.1.2
The physical location of this node (e.g., telephone closet, 3rd floor').
OBJECT-TYPE    
  DisplayString Size(0..256)  

switchSettingSystemContact 1.3.6.1.4.1.24062.2.2.17.2.1.3
The textual identification of the contact person for this managed node, together with information on how to contact this person.
OBJECT-TYPE    
  DisplayString Size(0..256)  

adminPasswordUserName 1.3.6.1.4.1.24062.2.2.17.2.2.1
The name(ID) of security manager.
OBJECT-TYPE    
  DisplayString Size(0..20)  

adminPasswordPassword 1.3.6.1.4.1.24062.2.2.17.2.2.2
The password of security manager. This object can't be read. it's write-only.
OBJECT-TYPE    
  DisplayString Size(0..8)  

ipConfigurationTable 1.3.6.1.4.1.24062.2.2.17.2.3.1
Table of descriptive information and configuration about the IP of the device.
OBJECT-TYPE    
  SEQUENCE OF  
    IPconfigurationEntry

ipConfigurationEntry 1.3.6.1.4.1.24062.2.2.17.2.3.1.1
Information configuring static IP or DHCP configuration of the device.
OBJECT-TYPE    
  IPconfigurationEntry  

ipConfigurationIndex 1.3.6.1.4.1.24062.2.2.17.2.3.1.1.1
This object identifies IP configuration entries.
OBJECT-TYPE    
  INTEGER  

ipConfigurationDHCPStatus 1.3.6.1.4.1.24062.2.2.17.2.3.1.1.2
Parameter configuring DHCP client functionality of the device. When enabled, device will be a DHCP client and request for the IP configuration from DHCP server. The Dynamic Host Configuration Protocol (DHCP) automates the assignment of IP addresses, subnet masks, default routers, and other IP parameters. The assignment usually occurs when the DHCP-configured machine boots up or regains connectivity to the network. The DHCP client sends out a query requesting a response from a DHCP server on the locally attached network. The query is typically initiated immediately after booting up and before the client initiates any IP based communication with other hosts. The DHCP server then replies to the client with its assigned IP address, subnet mask, DNS server and default gateway information. Note: Other items in this table will not be modified, when ipConfigurationDHCPStatus is enabled.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

ipConfigurationAddress 1.3.6.1.4.1.24062.2.2.17.2.3.1.1.3
The IP address of switch. An IP address (Internet Protocol address) is a unique address that devices use in order to identify and communicate with each other on a computer network utilizing the Internet Protocol standard (IP). Any participating network device can has its own unique address.
OBJECT-TYPE    
  IpAddress  

ipConfigurationSubMask 1.3.6.1.4.1.24062.2.2.17.2.3.1.1.4
The subnet mask is a 32-bit number in the same format and representation as IP addresses. The subnet mask determines which bits in the IP address are interpreted as the network number, which as the subnetwork number, and which as the host number. Each IP address bit that corresponds to a 1 in the subnet mask is in the network/subnetwork part of the address. This group of numbers is also called the Network ID. Each IP address bit that corresponds to a 0 is in the host part of the IP address.
OBJECT-TYPE    
  IpAddress  

ipConfigurationGateway 1.3.6.1.4.1.24062.2.2.17.2.3.1.1.5
The default gateway IP address identifies the gateway (for example, a router) that receives and forwards those packets whose addresses are unknown to the local network. The agent uses the default gateway address when sending alert packets to the management workstation on a network other than the local network.
OBJECT-TYPE    
  IpAddress  

ipConfigurationDNS1 1.3.6.1.4.1.24062.2.2.17.2.3.1.1.6
Parameter configuring the first DNS server of the device. The domain name system (DNS) stores and associates many types of information with domain names. Most importantly, it translates domain names (computer hostnames) to IP addresses, which makes it possible to attach easy-to-remember domain names to hard-to-remember IP addresses (such as 100.50.10.100).
OBJECT-TYPE    
  IpAddress  

ipConfigurationDNS2 1.3.6.1.4.1.24062.2.2.17.2.3.1.1.7
Parameter configuring the second DNS server of the device.
OBJECT-TYPE    
  IpAddress  

ipConfigurationStatus 1.3.6.1.4.1.24062.2.2.17.2.3.1.1.8
The status of the IP configuration entry. Only one configuration entry is supported on the device. Set active(1) to activate the parameters of the entry on the device.
OBJECT-TYPE    
  RowStatus  

systemTime 1.3.6.1.4.1.24062.2.2.17.2.4.1
current system time in format yyyy.mm.dd-hh:mm:ss
OBJECT-TYPE    
  DisplayString  

utcTimeZone 1.3.6.1.4.1.24062.2.2.17.2.4.2
UTC Timezone list. (GMT-12:00) Eniwetok, Kwajalein (GMT-11:00) Midway Island, Samoa (GMT-10:00) Hawaii (GMT-09:00) Alaska (GMT-08:00) Pacific Time (US & Canada), Tijuana (GMT-07:00) Arizona (GMT-07:00) Mountain Time (US & Canada) (GMT-06:00) Central America (GMT-06:00) Central Time (US & Canada) (GMT-06:00) Mexico City (GMT-06:00) Saskatchewan (GMT-05:00) Bogota, Lima, Quito (GMT-05:00) Eastern Time (US & Canada) (GMT-05:00) Indiana (East) (GMT-04:00) Atlantic Time (Canada) (GMT-04:00) Caracas, La Paz (GMT-04:00) Santiago (GMT-03:00) NewFoundland (GMT-03:00) Brasilia (GMT-03:00) Buenos Aires, Georgetown (GMT-03:00) Greenland (GMT-02:00) Mid-Atlantic (GMT-01:00) Azores (GMT-01:00) Cape Verde Is. (GMT) Casablanca, Monrovia (GMT) Greenwich Mean Time: Dublin, Edinburgh, Lisbon, London (GMT+01:00) Amsterdam, Berlin, Bern, Rome, Stockholm, Vienna (GMT+01:00) Belgrade, Bratislava, Budapest, Ljubljana, Prague (GMT+01:00) Brussels, Copenhagen, Madrid, Paris (GMT+01:00) Sarajevo, Skopje, Sofija, Vilnius, Warsaw, Zagreb (GMT+01:00) West Central Africa (GMT+02:00) Athens, Istanbul, Minsk (GMT+02:00) Bucharest (GMT+02:00) Cairo (GMT+02:00) Harare, Pretoria (GMT+02:00) Helsinki, Riga, Tallinn (GMT+02:00) Jerusalem (GMT+03:00) Baghdad (GMT+03:00) Kuwait, Riyadh (GMT+03:00) Moscow, St. Petersburg, Volgograd (GMT+03:00) Nairobi (GMT+03:30) Tehran (GMT+04:00) Abu Dhabi, Muscat (GMT+04:00) Baku, Tbilisi, Yerevan (GMT+04:30) Kabul (GMT+05:00) Ekaterinburg (GMT+05:00) Islamabad, Karachi, Tashkent (GMT+05:30) Calcutta, Chennai, Mumbai, New Delhi (GMT+05:45) Kathmandu (GMT+06:00) Almaty, Novosibirsk (GMT+06:00) Astana, Dhaka (GMT+06:00) Sri Jayawardenepura (GMT+06:30) Rangoon (GMT+07:00) Bangkok, Hanoi, Jakarta (GMT+07:00) Krasnoyarsk (GMT+08:00) Beijing, Chongqing, Hong Kong, Urumqi (GMT+08:00) Irkutsk, Ulaan Bataar (GMT+08:00) Kuala Lumpur, Singapore (GMT+08:00) Perth (GMT+08:00) Taipei (GMT+09:00) Osaka, Sapporo, Tokyo (GMT+09:00) Seoul (GMT+09:00) Yakutsk (GMT+09:30) Adelaide (GMT+09:30) Darwin (GMT+10:00) Brisbane (GMT+10:00) Canberra, Melbourne, Sydney (GMT+10:00) Guam, Port Moresby (GMT+10:00) Hobart (GMT+10:00) Vladivostok (GMT+11:00) Magadan, Solomon Is., New Caledonia (GMT+12:00) Aukland, Wellington (GMT+12:00) Fiji, Kamchatka, Marshall Is. (GMT+13:00) Nuku'alofa
OBJECT-TYPE    
  INTEGER gmtNegative1200EniwetokKwajalein(1), gmtNegative1100MidwayIslandSamoa(2), gmtNegative1000Hawaii(3), gmtNegative0900Alaska(4), gmtNegative0800PacificTimeUSandCanadaTijuana(5), gmtNegative0700Arizona(6), gmtNegative0700MountainTimeUSandCanada(7), gmtNegative0600CentralAmerica(8), gmtNegative0600CentralTimeUSandCanada(9), gmtNegative0600MexicoCityTegucigalpa(10), gmtNegative0600Saskatchewan(11), gmtNegative0500BogotaLimaQuito(12), gmtNegative0500EasternTimeUSandCanada(13), gmtNegative0500IndianaEast(14), gmtNegative0400AtlanticTimeCanada(15), gmtNegative0400CaracasLaPaz(16), gmtNegative0400Santiago(17), gmtNegative0330Newfoundland(18), gmtNegative0300Brasilia(19), gmtNegative0300BuenosAiresGeorgetown(20), gmtNegative0300Greenland(21), gmtNegative0200Mid-Atlantic(22), gmtNegative0100AzoresCapeVerdeIs(23), gmtNegative0100CapeVerdeIs(24), gmtCasablancaMonrovia(25), gmtGreenwichMeanTimeDublinEdinburghLisbonLondon(26), gmtPositive0100AmsterdamBerlinBernRomeStockholmVienna(27), gmtPositive0100BelgradeBratislavaBudapestLjubljanaPrague(28), gmtPositive0100BrusselsCopenhagenMadridParis(29), gmtPositive0100SarajevoSkopjeSofijaWarsawZagreb(30), gmtPositive0100WestCentralAfrica(31), gmtPositive0200AthensIstanbulMinsk(32), gmtPositive0200Bucharest(33), gmtPositive0200Cairo(34), gmtPositive0200HararePretoria(35), gmtPositive0200HelsinkiRigaTallinn(36), gmtPositive0200Jerusalem(37), gmtPositive0300BaghdadKuwaitRiyadh(38), gmtPositive0300KuwaitRiyadh(39), gmtPositive0300MoscowStPetersburgVolgograd(40), gmtPositive0300Mairobi(41), gmtPositive0330Tehran(42), gmtPositive0400AbuDhabiMuscat(43), gmtPositive0400BakuTbilisi(44), gmtPositive0430Kabul(45), gmtPositive0500Ekaterinburg(46), gmtPositive0500IslamabadKarachiTashkent(47), gmtPositive0530BombayCalcuttaMadrasNewDelhi(48), gmtPositive0545Kathmandu(49), gmtPositive0600AlmatyNovosibirsk(50), gmtPositive0600AstanaDhaka(51), gmtPositive0600Colombo(52), gmtPositive0630Rangoon(53), gmtPositive0700BangkokHanoiJakarta(54), gmtPositive0700Krasnoyarsk(55), gmtPositive0800BeijingChongqingHongKongUrumqi(56), gmtPositive0800IrkutskUlaanBataar(57), gmtPositive0800KualaLumpurSingapore(58), gmtPositive0800Perth(59), gmtPositive0800Taipei(60), gmtPositive0900OsakaSapporoTokyo(61), gmtPositive0900Seoul(62), gmtPositive0900Yakutsk(63), gmtPositive0930Adelaide(64), gmtPositive0930Darwin(65), gmtPositive1000Brisbane(66), gmtPositive1000CanberraMelbourneSydney(67), gmtPositive1000GuamPortMoresby(68), gmtPositive1000Hobart(69), gmtPositive1000Vladivostok(70), gmtPositive1100MagadanSolomonIsNewCaledonia(71), gmtPositive1200AucklandWllington(72), gmtPositive1200FijiKamchatkaMarshallIs(73), gmtPositive1300Nukualofa(74)  

dayLightSavingTime 1.3.6.1.4.1.24062.2.2.17.2.4.3
OBJECT IDENTIFIER    

ieee1588 1.3.6.1.4.1.24062.2.2.17.2.4.4
OBJECT IDENTIFIER    

clockSource 1.3.6.1.4.1.24062.2.2.17.2.4.5
OBJECT IDENTIFIER    

daylightSavingTimeStart 1.3.6.1.4.1.24062.2.2.17.2.4.3.1
The start-time of daylight saveing period, in format mm.n.d/hh:mm m is month, valid range 1-12 (1=January, 2=February, ..., 12=December). n is week of the month (1 to 5, 5 means the last week). d is weekday, valid range 0-6 (0=Sunday, 1=Monday, ..., 6=Saturday). hh:mm is time.
OBJECT-TYPE    
  DisplayString Size(0..12)  

daylightSavingTimeEnd 1.3.6.1.4.1.24062.2.2.17.2.4.3.2
The end-time of daylight saveing period, in format mm.n.d/hh:mm m is month, valid range 1-12 (1=January, 2=February, ..., 12=December). n is week of the month (1 to 5, 5 means the last week). d is weekday, valid range 0-6 (0=Sunday, 1=Monday, ..., 6=Saturday). hh:mm is time.
OBJECT-TYPE    
  DisplayString Size(0..12)  

daylightSavingOffset 1.3.6.1.4.1.24062.2.2.17.2.4.3.3
Daylight Saving Offset(Usually is 60 mins). When Enable and current time at Daylight Saving Period, the current time of the switch will be offseted by Daylight Saving Offset.
OBJECT-TYPE    
  Integer32  

daylightSavingTimeStatus 1.3.6.1.4.1.24062.2.2.17.2.4.3.4
(1)Enable Daylight Saving Time. (2)Disable Daylight Saving Time. Daylight Saving Time: Use this OID to Enable/Disable Daylight Saving Time.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

clockSourceSelection 1.3.6.1.4.1.24062.2.2.17.2.4.5.1
.
OBJECT-TYPE    
  INTEGER manual(1), ntp(2)  

clockSourceManual 1.3.6.1.4.1.24062.2.2.17.2.4.5.2
OBJECT IDENTIFIER    

clockSourceNtp 1.3.6.1.4.1.24062.2.2.17.2.4.5.3
OBJECT IDENTIFIER    

clockSourceManualSetting 1.3.6.1.4.1.24062.2.2.17.2.4.5.2.1
set system time, in format yyyy.mm.dd-hh:mm:ss
OBJECT-TYPE    
  DisplayString Size(0..19)  

ntpTable 1.3.6.1.4.1.24062.2.2.17.2.4.5.3.1
Table of descriptive information and configuration about NTP servers. NTP (Network Time Protocol) synchronizes timekeeping among a set of distributed time servers and clients. This synchronization allows events to be correlated when system logs are created and other time-specific events occur. An NTP server is configured to synchronize NTP clients. Servers can be configured to synchronize any client or only specific clients. NTP servers, however, will accept no synchronization information from their clients and therefore will not let clients update or affect the server's time settings. This switch acts as an NTP client, which tries to let its clock be set and synchronized by an external NTP timeserver. It can be configured to use multiple servers (upto 4 servers).
OBJECT-TYPE    
  SEQUENCE OF  
    NtpEntry

ntpEntry 1.3.6.1.4.1.24062.2.2.17.2.4.5.3.1.1
Information configuring IP addresses of NTP servers.
OBJECT-TYPE    
  NtpEntry  

ntpIndex 1.3.6.1.4.1.24062.2.2.17.2.4.5.3.1.1.1
This object identifies the entry.
OBJECT-TYPE    
  Integer32  

ntpServerIP 1.3.6.1.4.1.24062.2.2.17.2.4.5.3.1.1.2
The IP address of an NTP Server. Set 0.0.0.0 or 255.255.255.255 to remove this config.
OBJECT-TYPE    
  IpAddress  

ptpState 1.3.6.1.4.1.24062.2.2.17.2.4.4.1
Enable or disable ieee1588 PTP daemon
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

ptpMode 1.3.6.1.4.1.24062.2.2.17.2.4.4.2
Set PTP mode: Auto: Auto select master or slave. Master: Act as PTP master. Master: Act as PTP slave.
OBJECT-TYPE    
  INTEGER auto(1), master(2), slave(3)  

dhcpServerEnable 1.3.6.1.4.1.24062.2.2.17.2.5.1
Enable or disable dhcp server function.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

dhcpServerPoolTable 1.3.6.1.4.1.24062.2.2.17.2.5.2
Table of descriptive information and configuration about DHCP server of the switch.
OBJECT-TYPE    
  SEQUENCE OF  
    DhcpServerPoolEntry

dhcpServerPoolEntry 1.3.6.1.4.1.24062.2.2.17.2.5.2.1
An entry containing DHCP server information of the switch.
OBJECT-TYPE    
  DhcpServerPoolEntry  

dhcpServerPoolIndex 1.3.6.1.4.1.24062.2.2.17.2.5.2.1.1
The index of the Address Pool.
OBJECT-TYPE    
  Integer32  

dhcpServerPoolName 1.3.6.1.4.1.24062.2.2.17.2.5.2.1.2
The address pool name.
OBJECT-TYPE    
  DisplayString Size(1..20)  

dhcpServerPoolNetwork 1.3.6.1.4.1.24062.2.2.17.2.5.2.1.3
The Subnet of the IP Address Pool.
OBJECT-TYPE    
  IpAddress  

dhcpServerPoolSubMask 1.3.6.1.4.1.24062.2.2.17.2.5.2.1.4
The subnet mask of the IP Address Pool.
OBJECT-TYPE    
  IpAddress  

dhcpServerPoolGateway 1.3.6.1.4.1.24062.2.2.17.2.5.2.1.5
The gateway address of the IP Address Pool.
OBJECT-TYPE    
  IpAddress  

dhcpServerPoolLeaseTime 1.3.6.1.4.1.24062.2.2.17.2.5.2.1.6
The lease time(in second) of the Address Pool.
OBJECT-TYPE    
  Integer32  

dhcpServerPoolStatus 1.3.6.1.4.1.24062.2.2.17.2.5.2.1.7
The status of the Address Pool.
OBJECT-TYPE    
  RowStatus  

dhcpExcludedTable 1.3.6.1.4.1.24062.2.2.17.2.5.3
Table of descriptive information and configuration about DHCP server of the switch.
OBJECT-TYPE    
  SEQUENCE OF  
    DhcpExcludedEntry

dhcpExcludedEntry 1.3.6.1.4.1.24062.2.2.17.2.5.3.1
An entry containing DHCP server information of the switch.
OBJECT-TYPE    
  DhcpExcludedEntry  

dhcpExcludedIndex 1.3.6.1.4.1.24062.2.2.17.2.5.3.1.1
The index of the Excluded Table.
OBJECT-TYPE    
  Integer32  

dhcpExcludedIp 1.3.6.1.4.1.24062.2.2.17.2.5.3.1.2
The IP address .
OBJECT-TYPE    
  IpAddress  

dhcpExcludedStatus 1.3.6.1.4.1.24062.2.2.17.2.5.3.1.3
The status of a address pool.
OBJECT-TYPE    
  RowStatus  

dhcpManualBindingTable 1.3.6.1.4.1.24062.2.2.17.2.5.4
Table of descriptive information and configuration about DHCP server of the switch.
OBJECT-TYPE    
  SEQUENCE OF  
    DhcpManualBindingEntry

dhcpManualBindingEntry 1.3.6.1.4.1.24062.2.2.17.2.5.4.1
An entry containing DHCP server information of the switch.
OBJECT-TYPE    
  DhcpManualBindingEntry  

dhcpManualBindingIndex 1.3.6.1.4.1.24062.2.2.17.2.5.4.1.1
The index of the Static Binding Table.
OBJECT-TYPE    
  Integer32  

dhcpManualBindingIp 1.3.6.1.4.1.24062.2.2.17.2.5.4.1.2
The IP address.
OBJECT-TYPE    
  IpAddress  

dhcpManualBindingMac 1.3.6.1.4.1.24062.2.2.17.2.5.4.1.3
The MAC address.
OBJECT-TYPE    
  MacAddress  

dhcpManualBindingStatus 1.3.6.1.4.1.24062.2.2.17.2.5.4.1.4
The status of the binding.
OBJECT-TYPE    
  RowStatus  

dhcpStaticPortTable 1.3.6.1.4.1.24062.2.2.17.2.5.5
Table of descriptive information and configuration about DHCP server of the switch.
OBJECT-TYPE    
  SEQUENCE OF  
    DhcpStaticPortEntry

dhcpStaticPortEntry 1.3.6.1.4.1.24062.2.2.17.2.5.5.1
An entry containing DHCP server information of the switch.
OBJECT-TYPE    
  DhcpStaticPortEntry  

dhcpStaticPortIndex 1.3.6.1.4.1.24062.2.2.17.2.5.5.1.1
The index of the StaticPort Table.
OBJECT-TYPE    
  Integer32  

dhcpStaticPortNumber 1.3.6.1.4.1.24062.2.2.17.2.5.5.1.2
The port number .
OBJECT-TYPE    
  INTEGER  

dhcpStaticPortIp 1.3.6.1.4.1.24062.2.2.17.2.5.5.1.3
The IP address .
OBJECT-TYPE    
  IpAddress  

dhcpStaticPortStatus 1.3.6.1.4.1.24062.2.2.17.2.5.5.1.4
The status of a static port entry.
OBJECT-TYPE    
  RowStatus  

dhcpOption82Table 1.3.6.1.4.1.24062.2.2.17.2.5.6
DHCP server option82 table.
OBJECT-TYPE    
  SEQUENCE OF  
    DhcpOption82Entry

dhcpOption82Entry 1.3.6.1.4.1.24062.2.2.17.2.5.6.1
DHCP server option82 entry.
OBJECT-TYPE    
  DhcpOption82Entry  

dhcpOption82Index 1.3.6.1.4.1.24062.2.2.17.2.5.6.1.1
The index of the table.
OBJECT-TYPE    
  Integer32  

dhcpOption82CircuitIdType 1.3.6.1.4.1.24062.2.2.17.2.5.6.1.2
The Circuit-ID type of this option.
OBJECT-TYPE    
  INTEGER any(0), string(2), hexadecimal(3)  

dhcpOption82CircuitIdValue 1.3.6.1.4.1.24062.2.2.17.2.5.6.1.3
The Circuit-ID value of this option.
OBJECT-TYPE    
  OCTET STRING  

dhcpOption82RemoteIdType 1.3.6.1.4.1.24062.2.2.17.2.5.6.1.4
The Remote-ID type of this option.
OBJECT-TYPE    
  INTEGER any(0), string(2), hexadecimal(3)  

dhcpOption82RemoteIdValue 1.3.6.1.4.1.24062.2.2.17.2.5.6.1.5
The Remote-ID value of this option.
OBJECT-TYPE    
  OCTET STRING  

dhcpOption82Ip 1.3.6.1.4.1.24062.2.2.17.2.5.6.1.6
The IP Address bind to this option.
OBJECT-TYPE    
  IpAddress  

dhcpOption82Status 1.3.6.1.4.1.24062.2.2.17.2.5.6.1.7
he status of a static port entry.
OBJECT-TYPE    
  RowStatus  

dhcpServerLeasedTable 1.3.6.1.4.1.24062.2.2.17.2.5.7
Table of descriptive information and configuration about DHCP server of the switch.
OBJECT-TYPE    
  SEQUENCE OF  
    DhcpServerLeasedEntry

dhcpServerLeasedEntry 1.3.6.1.4.1.24062.2.2.17.2.5.7.1
An entry containing DHCP server information of the switch.
OBJECT-TYPE    
  DhcpServerLeasedEntry  

dhcpServerLeasedIndex 1.3.6.1.4.1.24062.2.2.17.2.5.7.1.1
The index of the Leased Table.
OBJECT-TYPE    
  Integer32  

dhcpServerLeasedIp 1.3.6.1.4.1.24062.2.2.17.2.5.7.1.2
The client IP address.
OBJECT-TYPE    
  IpAddress  

dhcpServerLeasedMac 1.3.6.1.4.1.24062.2.2.17.2.5.7.1.3
The client MAC address.
OBJECT-TYPE    
  MacAddress  

dhcpServerLeasedType 1.3.6.1.4.1.24062.2.2.17.2.5.7.1.4
.
OBJECT-TYPE    
  INTEGER manual(1), dynamic(2)  

dhcpServerLeasedTime 1.3.6.1.4.1.24062.2.2.17.2.5.7.1.5
The lease time of the client.
OBJECT-TYPE    
  Integer32  

dhcpRelayAgentEnable 1.3.6.1.4.1.24062.2.2.17.2.5.8
Enable or disable dhcp relay agent function.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

dhcpRelayAgentPolicy 1.3.6.1.4.1.24062.2.2.17.2.5.9
Keep(1): Keeps the original option 82 field and forwards to server drop(2): Drops the option 82 field and do not add any option 82 field replace(3): Replaces the existing option 82 field and adds new option 82 field. (This is the default setting)
OBJECT-TYPE    
  INTEGER keep(1), drop(2), replace(3)  

dhcpRelayAgentCircuitIdTable 1.3.6.1.4.1.24062.2.2.17.2.5.10
Description.
OBJECT-TYPE    
  SEQUENCE OF  
    DhcpRelayAgentCircuitIdEntry

dhcpRelayAgentCircuitIdEntry 1.3.6.1.4.1.24062.2.2.17.2.5.10.1
Description.
OBJECT-TYPE    
  DhcpRelayAgentCircuitIdEntry  

dhcpRelayAgentCircuitIdPortNum 1.3.6.1.4.1.24062.2.2.17.2.5.10.1.1
Description.
OBJECT-TYPE    
  Integer32  

dhcpRelayAgentCircuitIdType 1.3.6.1.4.1.24062.2.2.17.2.5.10.1.2
Circuit-ID type of the Option82 added by Relay Agent.
OBJECT-TYPE    
  Integer32 default(0), string(2), hexadecimal(3)  

dhcpRelayAgentCircuitIdValue 1.3.6.1.4.1.24062.2.2.17.2.5.10.1.3
Circuit-ID value of the Option82 added by Relay Agent, the format can be String or Hexadecimal value.
OBJECT-TYPE    
  OCTET STRING  

dhcpRelayAgentCircuitIdDisplay 1.3.6.1.4.1.24062.2.2.17.2.5.10.1.4
Display the Circuit-ID value by Hexadecimal format
OBJECT-TYPE    
  OCTET STRING  

dhcpRelayAgentRemoteIdType 1.3.6.1.4.1.24062.2.2.17.2.5.11
Remote-ID type of the Option82 added by Relay Agent.
OBJECT-TYPE    
  INTEGER default(0), string(2), hexadecimal(3), ip(4)  

dhcpRelayAgentRemoteIdValue 1.3.6.1.4.1.24062.2.2.17.2.5.12
Remote-ID value of the Option82 added by Relay Agent, the format can be String or Hexadecimal value.
OBJECT-TYPE    
  OCTET STRING  

dhcpRelayAgentRemoteIdDisplay 1.3.6.1.4.1.24062.2.2.17.2.5.13
Remote-ID value of the Option82 added by Relay Agent.
OBJECT-TYPE    
  OCTET STRING  

dhcpHelperAddressTable 1.3.6.1.4.1.24062.2.2.17.2.5.14
Table of descriptive information and configuration about DHCP relay helper address of the switch.
OBJECT-TYPE    
  SEQUENCE OF  
    DhcpHelperAddressEntry

dhcpHelperAddressEntry 1.3.6.1.4.1.24062.2.2.17.2.5.14.1
An entry containing DHCP relay information of the switch.
OBJECT-TYPE    
  DhcpHelperAddressEntry  

dhcpHelperAddress 1.3.6.1.4.1.24062.2.2.17.2.5.14.1.1
The IP address .
OBJECT-TYPE    
  IpAddress  

backupServerIP 1.3.6.1.4.1.24062.2.2.17.2.6.1
The IP address of a TFTP server to which a startup configuration can be uploaded.
OBJECT-TYPE    
  IpAddress  

backupAgentBoardFwFileName 1.3.6.1.4.1.24062.2.2.17.2.6.2
The filename to backup to.
OBJECT-TYPE    
  DisplayString Size(0..80)  

backupStatus 1.3.6.1.4.1.24062.2.2.17.2.6.3
Setting this object to active(1) trigger the TFTP upload action. Setting this object to notActive(2) has no effect. The system always returns the value notActive(2) when this object is read.
OBJECT-TYPE    
  INTEGER active(1), notActive(2)  

restoreServerIP 1.3.6.1.4.1.24062.2.2.17.2.6.4
The IP address of a TFTP server from which the startup configuration can be downloaded.
OBJECT-TYPE    
  IpAddress  

restoreAgentBoardFwFileName 1.3.6.1.4.1.24062.2.2.17.2.6.5
The file name to restore from.
OBJECT-TYPE    
  DisplayString Size(0..80)  

restoreStatus 1.3.6.1.4.1.24062.2.2.17.2.6.6
Setting this object to active(1) trigger the TFTP download action. Setting this object to notActive(2) has no effect. The system always returns the value notActive(2) when this object is read.
OBJECT-TYPE    
  INTEGER active(1), notActive(2)  

tftpDownloadServerIP 1.3.6.1.4.1.24062.2.2.17.2.7.1
The IP address of a TFTP server where a firmware image can be downloaded.
OBJECT-TYPE    
  IpAddress  

tftpDownloadAgentBoardFwFileName 1.3.6.1.4.1.24062.2.2.17.2.7.2
The file name of the firmware to be downloaded.
OBJECT-TYPE    
  DisplayString Size(0..80)  

tftpDownloadStatus 1.3.6.1.4.1.24062.2.2.17.2.7.3
Setting this object to active(1) trigger the TFTP download action. Setting this object to notActive(2) has no effect. The system always returns the value notActive(2) when this object is read.
OBJECT-TYPE    
  INTEGER active(1), notActive(2)  

factoryDefaultActive 1.3.6.1.4.1.24062.2.2.17.2.8.1
Set to active(1) to reload factory default configuration. Reloading factory default will overwrite your current configuration file with factocy default configuration while current IP configuration is reserved. Please reboot the device to make factory default configuration take effect. Set notActive(2) has no effect. The system always returns the value notActive(2) when this object is read.
OBJECT-TYPE    
  INTEGER active(1), notActive(2)  

systemRebootActive 1.3.6.1.4.1.24062.2.2.17.2.9.1
Set active(1) to restart the device. Set to notActive(2) has no effect. The device always returns the value notActive(2) when this object is read.
OBJECT-TYPE    
  INTEGER active(1), notActive(2)  

portControl 1.3.6.1.4.1.24062.2.2.17.3.1
OBJECT IDENTIFIER    

portStatus 1.3.6.1.4.1.24062.2.2.17.3.2
OBJECT IDENTIFIER    

rateLimiting 1.3.6.1.4.1.24062.2.2.17.3.3
OBJECT IDENTIFIER    

portTrunk 1.3.6.1.4.1.24062.2.2.17.3.4
OBJECT IDENTIFIER    

portCtrlTable 1.3.6.1.4.1.24062.2.2.17.3.1.1
Table of information and configuration for each ports.
OBJECT-TYPE    
  SEQUENCE OF  
    PortCtrlEntry

portCtrlEntry 1.3.6.1.4.1.24062.2.2.17.3.1.1.1
An entry containing information and configuration for a port.
OBJECT-TYPE    
  PortCtrlEntry  

portCtrlIndex 1.3.6.1.4.1.24062.2.2.17.3.1.1.1.1
Index of the port control entry.
OBJECT-TYPE    
  INTEGER  

portCtrlPortName 1.3.6.1.4.1.24062.2.2.17.3.1.1.1.2
The name of port.
OBJECT-TYPE    
  DisplayString Size(0..7)  

portCtrlPortStatus 1.3.6.1.4.1.24062.2.2.17.3.1.1.1.3
To enable or disable of this port.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

portCtrlSpeedAndDuplex 1.3.6.1.4.1.24062.2.2.17.3.1.1.1.4
Speed and duplex configuraion. Different speed and duplex modes are available. There are speeds: 100 megabits per second (Fast Ethernet), and 10 megabits per second (Legacy Ethernet). Full-duplex allows packets to be transmitted in both directions at the same time, while half-duplex allows a device to either transmit or receive, but not both at the same time. Full-duplex may have double bandwidth than half-duplex. You can configure manually from the possible options, listed from best to worst: 100Mb full-duplex(5) 100Mb half-duplex(4) 10Mb full-duplex(3) 10Mb half-duplex(2) Set to autoNegotiation(1) to allow the two interfaces on the link to exchange the capabilities and characteristics of the each side, and select the best operating mode automatically when a cable is plugged in.
OBJECT-TYPE    
  INTEGER autoNegotiation(1), tenMbpsHalfDuplex(2), tenMbpsFullDuplex(3), hundredMbpsHalfDuplex(4), hundredMbpsFullDuplex(5)  

portCtrlFlowControl 1.3.6.1.4.1.24062.2.2.17.3.1.1.1.5
Flow control configuration. Flow control is used to throttle the throughput rate of an end station to avoid dropping packets during network congestion. If flow control mode is not set and if there is no packet buffer space available, the incoming packets are discarded. Symmetric Flow Control stops and restarts packet transmission by transmitting and receiving pause frames. When a port's free buffer space is almost empty, the device send out a Pause frame to stop the remove node from sending more frames into the switch. When congestion on the port is relieved, the device send out a Pause frame with pause time equal to zero, making the remove node resume transmission.
OBJECT-TYPE    
  INTEGER disable(1), symmetric(2)  

portCtrlPortDescription 1.3.6.1.4.1.24062.2.2.17.3.1.1.1.6
The description of port.
OBJECT-TYPE    
  DisplayString Size(0..138)  

portStatusTable 1.3.6.1.4.1.24062.2.2.17.3.2.1
Table of descriptive and statistics information about each ports.
OBJECT-TYPE    
  SEQUENCE OF  
    PortStatusEntry

portStatusEntry 1.3.6.1.4.1.24062.2.2.17.3.2.1.1
An entry containing statistics information of a port.
OBJECT-TYPE    
  PortStatusEntry  

portStatusIndex 1.3.6.1.4.1.24062.2.2.17.3.2.1.1.1
Index of port statistic table.
OBJECT-TYPE    
  Integer32  

portStatusType 1.3.6.1.4.1.24062.2.2.17.3.2.1.1.2
Indicates the type of the port.
OBJECT-TYPE    
  INTEGER hundredBaseTX(1), hundredBaseFX(2), other(3), notPresent(4)  


portStatusState 1.3.6.1.4.1.24062.2.2.17.3.2.1.1.4
Indicate the state of the port.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

portStatusSpeedDuplex 1.3.6.1.4.1.24062.2.2.17.3.2.1.1.5
Indicate the speed and duplex mode of the port.
OBJECT-TYPE    
  INTEGER autoNegotiation(1), tenMbpsHalfDuplex(2), tenMbpsFullDuplex(3), hundredMbpsHalfDuplex(4), hundredMbpsFullDuplex(5)  

portStatusFlowCtrl 1.3.6.1.4.1.24062.2.2.17.3.2.1.1.6
Indicate the flow control status of the port.
OBJECT-TYPE    
  INTEGER disable(1), symmetric(2)  

sfpVender 1.3.6.1.4.1.24062.2.2.17.3.2.1.1.7
The vender name of the Small Form Pluggable (SFP) optical transceiver module.
OBJECT-TYPE    
  DisplayString  

sfpWavelength 1.3.6.1.4.1.24062.2.2.17.3.2.1.1.8
The wave length in nanometers (nm) of the Small Form Pluggable (SFP) optical transceiver module.
OBJECT-TYPE    
  Integer32  

sfpDistance 1.3.6.1.4.1.24062.2.2.17.3.2.1.1.9
The maximum transimission distance in meters of the Small Form Pluggable (SFP) optical transceiver module.
OBJECT-TYPE    
  Integer32  

rateLimitingTable 1.3.6.1.4.1.24062.2.2.17.3.3.1
Table of descriptive information and configuration about port rate limiting. You can set up bandwidth rate and packet limitation type for each ports. Rate limiting is used to control the rate of traffic sent or received on a network interface. For ingress rate limiting, traffic that is less than or equal to the specified rate is received, whereas traffic that exceeds the rate is dropped. For egress rate limiting, traffic that is less than or equal to the specified rate is sent, whereas traffic that exceeds the rate is dropped.
OBJECT-TYPE    
  SEQUENCE OF  
    RateLimitingEntry

rateLimitingEntry 1.3.6.1.4.1.24062.2.2.17.3.3.1.1
An entry containing information and configuration about port rate limiting.
OBJECT-TYPE    
  RateLimitingEntry  

rateLimitingPortNum 1.3.6.1.4.1.24062.2.2.17.3.3.1.1.1
The port number.
OBJECT-TYPE    
  Integer32  

rateLimitingIngressLimitType 1.3.6.1.4.1.24062.2.2.17.3.3.1.1.2
The type of ingress packets to be filtered.
OBJECT-TYPE    
  INTEGER all(1), broadcastMulticastFloodedUnicast(2), broadcastMulticast(3), broadcastOnly(4)  

rateLimitingIngressRate 1.3.6.1.4.1.24062.2.2.17.3.3.1.1.3
Ingress rate in Mbps, the rate range is from 1 Mbps to 100 Mbps and zero means no limit.
OBJECT-TYPE    
  Integer32  

rateLimitingEgressRate 1.3.6.1.4.1.24062.2.2.17.3.3.1.1.4
Egress rate in Mbps, the rate range is from 1 Mbps to 100 Mbps and zero means no limit. Egress rate limiting has effect on all types of packets, including unicast, multicast and broadcast packets.
OBJECT-TYPE    
  Integer32  

aggregatorSetting 1.3.6.1.4.1.24062.2.2.17.3.4.1
OBJECT IDENTIFIER    

aggregatorStatus 1.3.6.1.4.1.24062.2.2.17.3.4.2
OBJECT IDENTIFIER    

portTrunkAggregatorSettingTable 1.3.6.1.4.1.24062.2.2.17.3.4.1.1
Table of descriptive information and configuration about of each trunk group in this system. Link aggregation, or IEEE 802.3ad, is a method of combining physical network links into a single logical link for increased bandwidth. With Link aggregation we are able to increase the capacity and availability of the communications channel between devices (both switches and end stations) using existing Fast Ethernet and Gigabit Ethernet technology. Two or more Gigabit Ethernet connections are combined in order to increase the bandwidth capability and to create resilient and redundant links. A set of multiple parallel physical links between two devices is grouped together to form a single logical link. Link Aggregation also provides load balancing where the processing and communications activity is distributed across the links in a trunk so that no single link is overwhelmed.
OBJECT-TYPE    
  SEQUENCE OF  
    PortTrunkAggregatorSettingEntry

portTrunkAggregatorSettingEntry 1.3.6.1.4.1.24062.2.2.17.3.4.1.1.1
Information controlling aggregator configuration.
OBJECT-TYPE    
  PortTrunkAggregatorSettingEntry  

portTrunkPortIndex 1.3.6.1.4.1.24062.2.2.17.3.4.1.1.1.1
The port number.
OBJECT-TYPE    
  INTEGER  

portTrunkAggregatorGroupId 1.3.6.1.4.1.24062.2.2.17.3.4.1.1.1.2
Trunk group Id. Upto 8 ports can be aggregated into a group and 8 groups can be configured in the device.
OBJECT-TYPE    
  INTEGER trunkGroup1(1), trunkGroup2(2), trunkGroup3(3), trunkGroup4(4), trunkGroup5(5), trunkGroup6(6), trunkGroup7(7), trunkGroup8(8), none(9)  

portTrunkAggregatorType 1.3.6.1.4.1.24062.2.2.17.3.4.1.1.1.3
The Aggregator type. You can assign the aggregator staticly by setting to static(1), or setting to lacp(2) to enable the LACP protocol. The Link Aggregation Control Protocol (LACP) is required for dynamically exchanging configuration information between the peer devices in order to automatically configure and maintain link aggregation groups. The protocol is able to automatically detect the presence and capabilities of other aggregation capable devices, i.e. with LACP it is possible to specify which links in a system can be aggregated. This column has no effect if Group Id is set to none.
OBJECT-TYPE    
  INTEGER static(1), lacp(2)  

portTrunkAggregatorSettingApply 1.3.6.1.4.1.24062.2.2.17.3.4.1.2
set active(1) to apply the configuration
OBJECT-TYPE    
  INTEGER active(1), notactive(2)  

portTrunkAggregatorStatusTable 1.3.6.1.4.1.24062.2.2.17.3.4.2.1
Table of descriptive information about trunk groups in the device.
OBJECT-TYPE    
  SEQUENCE OF  
    PortTrunkAggregatorStatusEntry

portTrunkAggregatorStatusEntry 1.3.6.1.4.1.24062.2.2.17.3.4.2.1.1
An entry containing information about current configuration of trunk groups.
OBJECT-TYPE    
  PortTrunkAggregatorStatusEntry  

portTrunkAggregatorGroupIndex 1.3.6.1.4.1.24062.2.2.17.3.4.2.1.1.1
The trunk group identifier.
OBJECT-TYPE    
  INTEGER  

portTrunkAggregatorGroupType 1.3.6.1.4.1.24062.2.2.17.3.4.2.1.1.2
The Aggregator type. (1) The trunk group is LACP disabled and configured staticly by administrator. (2) The trunk group is LACP enabled.
OBJECT-TYPE    
  INTEGER static(1), lacp(2)  

portTrunkAggregatorGroupMember 1.3.6.1.4.1.24062.2.2.17.3.4.2.1.1.3
The ports are aggregated with other ports.
OBJECT-TYPE    
  PortList  

portTrunkAggregatorIndividual 1.3.6.1.4.1.24062.2.2.17.3.4.2.1.1.4
A port is LACP enabled but not aggregated with other ports.
OBJECT-TYPE    
  PortList  

portTrunkAggregatorLinkDown 1.3.6.1.4.1.24062.2.2.17.3.4.2.1.1.5
The ports which are linked down.
OBJECT-TYPE    
  PortList  

rstp 1.3.6.1.4.1.24062.2.2.17.4.2
OBJECT IDENTIFIER    

bridgeInformation 1.3.6.1.4.1.24062.2.2.17.4.3
OBJECT IDENTIFIER    

multipleSuperRing 1.3.6.1.4.1.24062.2.2.17.4.4
OBJECT IDENTIFIER    

mstp 1.3.6.1.4.1.24062.2.2.17.4.5
OBJECT IDENTIFIER    

mstpBridgeInformation 1.3.6.1.4.1.24062.2.2.17.4.6
OBJECT IDENTIFIER    

multipleSuperRingConfigTable 1.3.6.1.4.1.24062.2.2.17.4.4.1
Table of configuration about redundany protocol in the device.
OBJECT-TYPE    
  SEQUENCE OF  
    MultipleSuperRingConfigEntry

multipleSuperRingConfigEntry 1.3.6.1.4.1.24062.2.2.17.4.4.1.1
An entry containing information about current configuration of rings.
OBJECT-TYPE    
  MultipleSuperRingConfigEntry  

superRingConfigId 1.3.6.1.4.1.24062.2.2.17.4.4.1.1.1
Ring Id.
OBJECT-TYPE    
  INTEGER 0..15  

superRingName 1.3.6.1.4.1.24062.2.2.17.4.4.1.1.2
Super Ring name.
OBJECT-TYPE    
  DisplayString  

superRingConfigVersion 1.3.6.1.4.1.24062.2.2.17.4.4.1.1.3
Super Ring funtion version selection. Super Ring: Backward compatible with legacy super ring mechanism. Note: This model supports v1 non-Redundancy Management mode only. Rapid Super Ring: New mechanism. The recovery time is less than 30ms.
OBJECT-TYPE    
  INTEGER superRing(1), rapidSuperRing(2)  

superRingDevicePriority 1.3.6.1.4.1.24062.2.2.17.4.4.1.1.4
Super Ring device priority setting.
OBJECT-TYPE    
  INTEGER 0..255  

superRingRingPort1 1.3.6.1.4.1.24062.2.2.17.4.4.1.1.5
RingPort1 should not equal to RingRort2.
OBJECT-TYPE    
  INTEGER  

superRingRingPort2 1.3.6.1.4.1.24062.2.2.17.4.4.1.1.6
RingPort2 should not equal to RingRort1.
OBJECT-TYPE    
  INTEGER  

superRingRingPort1PathCost 1.3.6.1.4.1.24062.2.2.17.4.4.1.1.7
Tok_String
OBJECT-TYPE    
  INTEGER 0..255  

superRingRingPort2PathCost 1.3.6.1.4.1.24062.2.2.17.4.4.1.1.8
Tok_String
OBJECT-TYPE    
  INTEGER 0..255  

superRingRapidDualHomingStatus 1.3.6.1.4.1.24062.2.2.17.4.4.1.1.9
Rapid Dual Homing funtion status. Rapid Dual Homing is a redundancy protocol, which is compatible with RSTP. (1) Rapid Dual Homing function is enabled. (2) Rapid Dual Homing function is disabled.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

superRingStatus 1.3.6.1.4.1.24062.2.2.17.4.4.1.1.10
Status of this ring.
OBJECT-TYPE    
  RowStatus  

multipleSuperRingStatusTable 1.3.6.1.4.1.24062.2.2.17.4.4.2
Table of status information about redundany protocol in the device.
OBJECT-TYPE    
  SEQUENCE OF  
    MultipleSuperRingStatusEntry

multipleSuperRingStatusEntry 1.3.6.1.4.1.24062.2.2.17.4.4.2.1
An entry containing information about current status of rings.
OBJECT-TYPE    
  MultipleSuperRingStatusEntry  

superRingStatusId 1.3.6.1.4.1.24062.2.2.17.4.4.2.1.1
Ring Id.
OBJECT-TYPE    
  INTEGER 0..15  

superRingVersion 1.3.6.1.4.1.24062.2.2.17.4.4.2.1.2
Super Ring funtion version selection. Super Ring: Backward compatible with legacy super ring mechanism. Note: This model supports v1 non-Redundancy Management mode only. Rapid Super Ring: New mechanism. The recovery time is less than 30ms. Not Supported:
OBJECT-TYPE    
  INTEGER superRing(1), rapidSuperRing(2), notSupported(4)  

superRingDeviceRole 1.3.6.1.4.1.24062.2.2.17.4.4.2.1.3
Super Ring role status. (1) disabled. (2) Redundancy manager. (3) Non redundancy manager.
OBJECT-TYPE    
  INTEGER disabled(1), rm(2), non-RM(3)  

superRingRingPortList1 1.3.6.1.4.1.24062.2.2.17.4.4.2.1.4
Port list for ring port1.
OBJECT-TYPE    
  PortList  

superRingRingPortList2 1.3.6.1.4.1.24062.2.2.17.4.4.2.1.5
Port list for ring port2.
OBJECT-TYPE    
  PortList  

superRingRingStatus 1.3.6.1.4.1.24062.2.2.17.4.4.2.1.6
Super Ring ring status. (1) Disabled - The ring on this device is disabled. (1) Normal - Ring is complete. (2) Abnormal - Ring is not complete.
OBJECT-TYPE    
  INTEGER disabled(1), normal(2), abnormal(3)  

superRingRmMac 1.3.6.1.4.1.24062.2.2.17.4.4.2.1.7
RM mac address.
OBJECT-TYPE    
  MacAddress  

superRingBlockedPort 1.3.6.1.4.1.24062.2.2.17.4.4.2.1.8
The blocked ports in ring Normal state.
OBJECT-TYPE    
  PortList  

superRingRoleTransitionCount 1.3.6.1.4.1.24062.2.2.17.4.4.2.1.9
Tok_String
OBJECT-TYPE    
  Integer32  

superRingRingStateTransitionCount 1.3.6.1.4.1.24062.2.2.17.4.4.2.1.10
Tok_String
OBJECT-TYPE    
  Integer32  

rstpStatus 1.3.6.1.4.1.24062.2.2.17.4.2.1
Enable Spanning Tree protocol, Rapid Spanning Tree protocol, or disable . Rapid Spanning Tree Algorithm and Protocol (RSTP) provides a loop free topology for any LAN or bridged network. RSTP is an evolution of the Spanning Tree Protocol (STP), and was introduced in the extension IEEE 802.1w, and provides for faster spanning tree convergence after a topology change.
OBJECT-TYPE    
  INTEGER stp(1), rstp(2), mstp(3), disabled(4)  

rstpPriority 1.3.6.1.4.1.24062.2.2.17.4.2.2
A value used to identify the root bridge. The bridge with the lowest value has the highest priority and is selected as the root. Enter a number 0 through 61440 in steps of 4096. If you change the value, you must restart RSTP. This item can't be modified, if rstpStatus was disabled.
OBJECT-TYPE    
  Integer32 priority0(0), priority4096(4096), priority8192(8192), priority12288(12288), priority16384(16384), priority20480(20480), priority24576(24576), priority28672(28672), priority32768(32768), priority36864(36864), priority40960(40960), priority45056(45056), priority49152(49152), priority53248(53248), priority57344(57344), priority61440(61440)  

rstpMaxAge 1.3.6.1.4.1.24062.2.2.17.4.2.3
The number of seconds a bridge waits without receiving Spanning-Tree Protocol configuration messages before attempting a reconfiguration. Enter a number 6 through 40. Note: 2*(Forward Delay Time-1) should be greater than or equal to the Max Age. The Max Age should be greater than or equal to 2*(Hello Time + 1). This item can't be modified, if rstpStatus was disabled.
OBJECT-TYPE    
  Integer32  

rstpHelloTime 1.3.6.1.4.1.24062.2.2.17.4.2.4
The number of seconds between the transmission of Spanning-Tree Protocol configuration messages. Enter a number 1 through 10 Note: 2*(Forward Delay Time-1) should be greater than or equal to the Max Age. The Max Age should be greater than or equal to 2*(Hello Time + 1). This item can't be modified, if rstpStatus was disabled.
OBJECT-TYPE    
  Integer32  

rstpForwardDelayTime 1.3.6.1.4.1.24062.2.2.17.4.2.5
The number of seconds a port waits before changing from its Spanning-Tree Protocol learning and listening states to the forwarding state. Enter a number 4 through 30. Note:2*(Forward Delay Time-1) should be greater than or equal to the Max Age. The Max Age should be greater than or equal to 2*(Hello Time + 1). This item can't be modified, if rstpStatus was disabled.
OBJECT-TYPE    
  Integer32  

rstpPerPortCfgTable 1.3.6.1.4.1.24062.2.2.17.4.2.6
Table of descriptive information and configuration about RSTP on each port.
OBJECT-TYPE    
  SEQUENCE OF  
    RstpPerPortCfgEntry

rstpPerPortCfgEntry 1.3.6.1.4.1.24062.2.2.17.4.2.6.1
Information configuring RSTP on a port.
OBJECT-TYPE    
  RstpPerPortCfgEntry  

rstpPerPortCfgPortNum 1.3.6.1.4.1.24062.2.2.17.4.2.6.1.1
The port number.
OBJECT-TYPE    
  Integer32  

rstpPerPortCfgPathCost 1.3.6.1.4.1.24062.2.2.17.4.2.6.1.2
The cost of the path to the other bridge from this transmitting bridge at the specified port. Enter a number from 1 through 200000000. (0 will auto set path cost to standard recommended value)
OBJECT-TYPE    
  Integer32  

rstpPerPortCfgPriority 1.3.6.1.4.1.24062.2.2.17.4.2.6.1.3
Decide which port should be blocked by priority in LAN. Enter a number from 0 through 240 in steps of 16.
OBJECT-TYPE    
  Integer32 priority0(0), priority16(16), priority32(32), priority48(48), priority64(64), priority80(80), priority96(96), priority112(112), priority128(128), priority144(144), priority160(160), priority176(176), priority192(192), priority208(208), priority224(224), priority240(240)  

rstpPerPortCfgAdminP2P 1.3.6.1.4.1.24062.2.2.17.4.2.6.1.4
Some of the rapid state transactions that are possible within RSTP are dependent upon whether the Port concerned can only be connected to exactly one other Bridge(ie., it is served by a point-to-point LAN segment), or can be connected to two or more Bridges(i.e., it is served by a shared medium LAN segment). The adminPointToPointMAC allow the p2p status of the link to be manipulated adminitratively.
OBJECT-TYPE    
  INTEGER auto(1), point2Point(2), shared(3), notSupport(4)  

rstpPerPortCfgAdminEdge 1.3.6.1.4.1.24062.2.2.17.4.2.6.1.5
Present in implementations that support the identification of edge ports. All ports directly connected to end stations cannot create bridging loops in the network and can thus directly transition to forwarding, skipping the listening and learning stages.
OBJECT-TYPE    
  INTEGER true(1), false(2)  

rstpRootBridgeInformationTable 1.3.6.1.4.1.24062.2.2.17.4.3.1
Table of descriptive information about root bridge of rapid spanning tree in this system.
OBJECT-TYPE    
  SEQUENCE OF  
    RstpRootBridgeInformationEntry

rstpRootBridgeInformationEntry 1.3.6.1.4.1.24062.2.2.17.4.3.1.1
An entry in the table, containing information about root bridge information of the RSTP.
OBJECT-TYPE    
  RstpRootBridgeInformationEntry  

rstpRootBridgeInformationIndex 1.3.6.1.4.1.24062.2.2.17.4.3.1.1.1
Index of root bridge information table.
OBJECT-TYPE    
  Integer32  

rstpRootBridgeInformationBridgeID 1.3.6.1.4.1.24062.2.2.17.4.3.1.1.2
Bridge ID.
OBJECT-TYPE    
  DisplayString Size(0..255)  

rstpRootBridgeInformationRootPriority 1.3.6.1.4.1.24062.2.2.17.4.3.1.1.3
Root Priority.
OBJECT-TYPE    
  Integer32  

rstpRootBridgeInformationRootPort 1.3.6.1.4.1.24062.2.2.17.4.3.1.1.4
Root Port.
OBJECT-TYPE    
  DisplayString Size(0..80)  

rstpRootBridgeInformationRootPathCost 1.3.6.1.4.1.24062.2.2.17.4.3.1.1.5
Root Path Cost.
OBJECT-TYPE    
  Integer32  

rstpRootBridgeInformationMaxAge 1.3.6.1.4.1.24062.2.2.17.4.3.1.1.6
Max Age.
OBJECT-TYPE    
  Integer32  

rstpRootBridgeInformationHelloTime 1.3.6.1.4.1.24062.2.2.17.4.3.1.1.7
Hello Time.
OBJECT-TYPE    
  Integer32  

rstpRootBridgeInformationForwardDelay 1.3.6.1.4.1.24062.2.2.17.4.3.1.1.8
Forward Delay Time.
OBJECT-TYPE    
  Integer32  

rstpPerPortInfoTable 1.3.6.1.4.1.24062.2.2.17.4.3.2
Table of descriptive information and configuration about rapid spanning tree (Per port).
OBJECT-TYPE    
  SEQUENCE OF  
    RstpPerPortInfoEntry

rstpPerPortInfoEntry 1.3.6.1.4.1.24062.2.2.17.4.3.2.1
An entry in the table, containing inforamtion about RSTP (Per port).
OBJECT-TYPE    
  RstpPerPortInfoEntry  

rstpPerPortInfoPortNum 1.3.6.1.4.1.24062.2.2.17.4.3.2.1.1
Port number.
OBJECT-TYPE    
  Integer32  

rstpPerPortInfoPathCost 1.3.6.1.4.1.24062.2.2.17.4.3.2.1.2
The cost of the path to the other bridge from this transmitting bridge at the specified port. Enter a number 1 through 200000000.
OBJECT-TYPE    
  Integer32  

rstpPerPortInfoPriority 1.3.6.1.4.1.24062.2.2.17.4.3.2.1.3
Decide which port should be blocked by priority in LAN. Enter a number 0 through 240 in steps of 16.
OBJECT-TYPE    
  Integer32  

rstpPerPortInfoAdminP2P 1.3.6.1.4.1.24062.2.2.17.4.3.2.1.4
Some of the rapid state transactions that are possible within RSTP are dependent upon whether the Port concerned can only be connected to exactly one other Bridge(ie., it is served by a point-to-point LAN segment), or can be connected to two or more Bridges(i.e., it is served by a shared medium LAN segment). The adminPointToPointMAC allow the p2p status of the link to be manipulated adminitratively. STP does not support this function.
OBJECT-TYPE    
  INTEGER auto(1), point2Point(2), shared(3), notSupport(4)  

rstpPerPortInfoAdminEdge 1.3.6.1.4.1.24062.2.2.17.4.3.2.1.5
Present in implementations that support the identification of edge ports. All ports directly connected to end stations cannot create bridging loops in the network and can thus directly transition to forwarding, skipping the listening and learning stages.
OBJECT-TYPE    
  INTEGER true(1), false(2)  

rstpPerPortInfoState 1.3.6.1.4.1.24062.2.2.17.4.3.2.1.6
OBJECT-TYPE    
  INTEGER nonStp(1), learning(2), forwarding(3), disabled(4), blocking(5), unknown(6)  

rstpPerPortInfoRole 1.3.6.1.4.1.24062.2.2.17.4.3.2.1.7
Descriptive information about RSTP switch port roles: disabled(1) RSTP is disabled on this port. root(2) A forwarding port that has been elected for the spanning-tree topology. designated(3) A forwarding port for every LAN segment. alternate(4) An alternate path to the root bridge. This path is different than using the root port. backup(5) A backup/redundant path to a segment where another switch port already connects.
OBJECT-TYPE    
  INTEGER disabled(1), root(2), designated(3), alternated(4), backup(5), nonStp(6), unknown(7)  

rstpPerPortInfoAggregated 1.3.6.1.4.1.24062.2.2.17.4.3.2.1.8
group ID(Static) or N/A or group ID(LACP)
OBJECT-TYPE    
  DisplayString Size(0..32)  

mstpRegionName 1.3.6.1.4.1.24062.2.2.17.4.5.1
MSTP region name.
OBJECT-TYPE    
  DisplayString  

mstpRegionRevision 1.3.6.1.4.1.24062.2.2.17.4.5.2
MSTP region revision.
OBJECT-TYPE    
  Integer32  

mstpPerInstCfgTable 1.3.6.1.4.1.24062.2.2.17.4.5.3
Table of descriptive information and configuration about STP on each port.
OBJECT-TYPE    
  SEQUENCE OF  
    MstpPerInstCfgEntry

mstpPerInstCfgEntry 1.3.6.1.4.1.24062.2.2.17.4.5.3.1
Information configuring MSTP on a instance.
OBJECT-TYPE    
  MstpPerInstCfgEntry  

mstpPerInstCfgInstanceID 1.3.6.1.4.1.24062.2.2.17.4.5.3.1.1
The instance ID.
OBJECT-TYPE    
  Integer32  

mstpPerInstCfgVlanGroup 1.3.6.1.4.1.24062.2.2.17.4.5.3.1.2
VLAN group of instance.
OBJECT-TYPE    
  DisplayString  

mstpPerInstCfgInstancePriority 1.3.6.1.4.1.24062.2.2.17.4.5.3.1.3
A value used to identify the instance root. The instance with the lowest value has the highest priority and is selected as the root. Enter a number 0 through 61440 in steps of 4096.
OBJECT-TYPE    
  Integer32 priority0(0), priority4096(4096), priority8192(8192), priority12288(12288), priority16384(16384), priority20480(20480), priority24576(24576), priority28672(28672), priority32768(32768), priority36864(36864), priority40960(40960), priority45056(45056), priority49152(49152), priority53248(53248), priority57344(57344), priority61440(61440)  

mstpPerInstCfgStatus 1.3.6.1.4.1.24062.2.2.17.4.5.3.1.4
Status of this Instance.
OBJECT-TYPE    
  RowStatus  

mstpPerPortCfgTable 1.3.6.1.4.1.24062.2.2.17.4.5.4
Table of descriptive information and configuration about MSTP on each port.
OBJECT-TYPE    
  SEQUENCE OF  
    MstpPerPortCfgEntry

mstpPerPortCfgEntry 1.3.6.1.4.1.24062.2.2.17.4.5.4.1
Information configuring MSTP on a port.
OBJECT-TYPE    
  MstpPerPortCfgEntry  

mstpPerPortCfgIndex 1.3.6.1.4.1.24062.2.2.17.4.5.4.1.1
The index of MstpPerPortCfgEntry.
OBJECT-TYPE    
  Integer32  

mstpPerPortCfgInstanceID 1.3.6.1.4.1.24062.2.2.17.4.5.4.1.2
The instance ID.
OBJECT-TYPE    
  Integer32  

mstpPerPortCfgPortNum 1.3.6.1.4.1.24062.2.2.17.4.5.4.1.3
The port number.
OBJECT-TYPE    
  Integer32  

mstpPerPortCfgPathCost 1.3.6.1.4.1.24062.2.2.17.4.5.4.1.4
The cost of the path to the other bridge from this transmitting bridge at the specified port. Enter a number from 1 through 200000000. (0 will auto set path cost to standard recommended value)
OBJECT-TYPE    
  Integer32  

mstpPerPortCfgPriority 1.3.6.1.4.1.24062.2.2.17.4.5.4.1.5
Decide which port should be blocked by priority in LAN. Enter a number from 0 through 240 in steps of 16.
OBJECT-TYPE    
  Integer32 priority0(0), priority16(16), priority32(32), priority48(48), priority64(64), priority80(80), priority96(96), priority112(112), priority128(128), priority144(144), priority160(160), priority176(176), priority192(192), priority208(208), priority224(224), priority240(240)  

mstpPerPortCfgLinkType 1.3.6.1.4.1.24062.2.2.17.4.5.4.1.6
Some of the rapid state transactions that are possible within RSTP are dependent upon whether the Port concerned can only be connected to exactly one other Bridge(ie., it is served by a point-to-point LAN segment), or can be connected to two or more Bridges(i.e., it is served by a shared medium LAN segment). The adminPointToPointMAC allow the p2p status of the link to be manipulated adminitratively.
OBJECT-TYPE    
  INTEGER auto(1), point2Point(2), shared(3), notSupport(4)  

mstpPerPortCfgEdgePort 1.3.6.1.4.1.24062.2.2.17.4.5.4.1.7
Present in implementations that support the identification of edge ports. All ports directly connected to end stations cannot create bridging loops in the network and can thus directly transition to forwarding, skipping the listening and learning stages.
OBJECT-TYPE    
  INTEGER true(1), false(2)  

mstpRootInformationTable 1.3.6.1.4.1.24062.2.2.17.4.6.1
Table of descriptive information about root bridge of rapid spanning tree in this system.
OBJECT-TYPE    
  SEQUENCE OF  
    MstpRootInformationEntry

mstpRootInformationEntry 1.3.6.1.4.1.24062.2.2.17.4.6.1.1
An entry in the table, containing information about root bridge information of the MSTP.
OBJECT-TYPE    
  MstpRootInformationEntry  

mstpRootInformationInstanceID 1.3.6.1.4.1.24062.2.2.17.4.6.1.1.1
The instance ID.
OBJECT-TYPE    
  Integer32  

mstpRootInformationRootAddress 1.3.6.1.4.1.24062.2.2.17.4.6.1.1.2
Root Address.
OBJECT-TYPE    
  DisplayString Size(0..255)  

mstpRootInformationRootPriority 1.3.6.1.4.1.24062.2.2.17.4.6.1.1.3
Root Priority.
OBJECT-TYPE    
  Integer32  

mstpRootInformationRootPort 1.3.6.1.4.1.24062.2.2.17.4.6.1.1.4
Root Port.
OBJECT-TYPE    
  DisplayString Size(0..80)  

mstpRootInformationRootPathCost 1.3.6.1.4.1.24062.2.2.17.4.6.1.1.5
Root Path Cost.
OBJECT-TYPE    
  Integer32  

mstpRootInformationMaxAge 1.3.6.1.4.1.24062.2.2.17.4.6.1.1.6
Max Age.
OBJECT-TYPE    
  Integer32  

mstpRootInformationHelloTime 1.3.6.1.4.1.24062.2.2.17.4.6.1.1.7
Hello Time.
OBJECT-TYPE    
  Integer32  

mstpRootInformationForwardDelay 1.3.6.1.4.1.24062.2.2.17.4.6.1.1.8
Forward Delay Time.
OBJECT-TYPE    
  Integer32  

mstpPerPortInfoTable 1.3.6.1.4.1.24062.2.2.17.4.6.2
Table of descriptive information and configuration about rapid spanning tree (Per port).
OBJECT-TYPE    
  SEQUENCE OF  
    MstpPerPortInfoEntry

mstpPerPortInfoEntry 1.3.6.1.4.1.24062.2.2.17.4.6.2.1
An entry in the table, containing information about MSTP (Per port).
OBJECT-TYPE    
  MstpPerPortInfoEntry  

mstpPerPortInfoIndex 1.3.6.1.4.1.24062.2.2.17.4.6.2.1.1
The index of MstpPerPortInfoEntry.
OBJECT-TYPE    
  Integer32  

mstpPerPortInfoInstanceID 1.3.6.1.4.1.24062.2.2.17.4.6.2.1.2
The instance ID.
OBJECT-TYPE    
  Integer32  

mstpPerPortInfoPortNum 1.3.6.1.4.1.24062.2.2.17.4.6.2.1.3
Port number.
OBJECT-TYPE    
  Integer32  

mstpPerPortInfoRole 1.3.6.1.4.1.24062.2.2.17.4.6.2.1.4
Descriptive information about MSTP switch port roles: disabled(1) MSTP is disabled on this port. root(2) A forwarding port that has been elected for the spanning-tree topology. designated(3) A forwarding port for every LAN segment. alternate(4) An alternate path to the root bridge. This path is different than using the root port. backup(5) A backup/redundant path to a segment where another switch port already connects.
OBJECT-TYPE    
  INTEGER root(1), alternate(2), designated(3), backup(4), master(5), disabled(6), boundary(7), unknown(8)  

mstpPerPortInfoState 1.3.6.1.4.1.24062.2.2.17.4.6.2.1.5
OBJECT-TYPE    
  INTEGER disabled(1), listening(2), learning(3), forwarding(4), blocking(5), unknown(6)  

mstpPerPortInfoPathCost 1.3.6.1.4.1.24062.2.2.17.4.6.2.1.6
The cost of the path to the other bridge from this transmitting bridge at the specified port. Enter a number 1 through 200000000.
OBJECT-TYPE    
  Integer32  

mstpPerPortInfoPriority 1.3.6.1.4.1.24062.2.2.17.4.6.2.1.7
Decide which port should be blocked by priority in LAN. Enter a number 0 through 240 in steps of 16.
OBJECT-TYPE    
  Integer32  

mstpPerPortInfoLinkType 1.3.6.1.4.1.24062.2.2.17.4.6.2.1.8
Some of the rapid state transactions that are possible within MSTP are dependent upon whether the Port concerned can only be connected to exactly one other Bridge(ie., it is served by a point-to-point LAN segment), or can be connected to two or more Bridges(i.e., it is served by a shared medium LAN segment). The adminPointToPointMAC allow the p2p status of the link to be manipulated adminitratively.
OBJECT-TYPE    
  INTEGER p2p-bound-stp(1), p2p-bound-rstp(2), p2p-bound-mstp(3), p2p-internal-mstp(4), shared-bound-stp(5), shared-bound-rstp(6), shared-bound-mstp(7), shared-internal-mstp(8)  

mstpPerPortInfoEdgePort 1.3.6.1.4.1.24062.2.2.17.4.6.2.1.9
Present in implementations that support the identification of edge ports. All ports directly connected to end stations cannot create bridging loops in the network and can thus directly transition to forwarding, skipping the listening and learning stages.
OBJECT-TYPE    
  INTEGER true(1), false(2)  

vlanManagementVlan 1.3.6.1.4.1.24062.2.2.17.5.1
The VLAN from which managemnet traffic can access the device. By default, VLAN 1 is management VLAN.
OBJECT-TYPE    
  INTEGER  

ieee8021qVlan 1.3.6.1.4.1.24062.2.2.17.5.2
OBJECT IDENTIFIER    

dot1qPortVlanTable 1.3.6.1.4.1.24062.2.2.17.5.2.1
A table containing per port control and status information for IEEE802.1Q VLAN configuration in the device.
OBJECT-TYPE    
  SEQUENCE OF  
    Dot1qPortVlanEntry

dot1qPortVlanEntry 1.3.6.1.4.1.24062.2.2.17.5.2.1.1
Information controlling IEEE802.1Q VLAN configuration for a port on the device.
OBJECT-TYPE    
  Dot1qPortVlanEntry  

dot1qPortIndex 1.3.6.1.4.1.24062.2.2.17.5.2.1.1.1
The port identifier.
OBJECT-TYPE    
  INTEGER 1..10  

dot1qPvid 1.3.6.1.4.1.24062.2.2.17.5.2.1.1.2
The default Port VID, the VLAN ID assigned to an untagged frame or a Priority-Tagged frame received on the port.
OBJECT-TYPE    
  INTEGER 1..4094  

dot1qPortAcceptableFrameTypes 1.3.6.1.4.1.24062.2.2.17.5.2.1.1.3
When admitOnlyVlanTagged(2) the device will discard untagged frames or Priority-Tagged only frames received on this port. When admitAll(1), untagged frames or Priority-Tagged only frames received on this port will be accepted and assigned the PVID for this frame. This control does not affect VLAN independent BPDU frames, such as SuperRing, STP, GVRP and LACP. It does affect VLAN dependent BPDU frames, such as GMRP.
OBJECT-TYPE    
  INTEGER admitAll(1), admitOnlyVlanTagged(2)  

dot1qPortIngressFiltering 1.3.6.1.4.1.24062.2.2.17.5.2.1.1.4
When true(1) the device will discard incoming frames whose VLAN classification do not include this port in its Member set. When false(2), the port will accept all incoming frames regardless its VLAN classification. This control does not affect VLAN independent BPDU frames, such as SuperRing, STP, GVRP and LACP. It does affect VLAN dependent BPDU frames, such as GMRP.
OBJECT-TYPE    
  INTEGER true(1), false(2)  

dot1qVlanStaticTable 1.3.6.1.4.1.24062.2.2.17.5.2.2
A table containing configuration information for each VLAN configured into the device by management. All entries are permanent and will be restored after the device is reset. Upto 64 VLANs can be configured in this device. IEEE 802.1Q Virtual LANs (VLANs) allow a single physical LAN to be partitioned into several smaller logical LANs. VLANs limit the broadcast domain, improve security and performance and are ideal for separating systems or departments from each other.
OBJECT-TYPE    
  SEQUENCE OF  
    Dot1qVlanStaticEntry

dot1qVlanStaticEntry 1.3.6.1.4.1.24062.2.2.17.5.2.2.1
Static information of a VLAN configured into the device by management.
OBJECT-TYPE    
  Dot1qVlanStaticEntry  

dot1qVlanIndex 1.3.6.1.4.1.24062.2.2.17.5.2.2.1.1
The VLAN Identifier (VID) refering to this VLAN. The valid range is from 1 to 4094.
OBJECT-TYPE    
  INTEGER 1..4094  

dot1qVlanStaticName 1.3.6.1.4.1.24062.2.2.17.5.2.2.1.2
An administratively assigned string, which is used to identify the VLAN.
OBJECT-TYPE    
  DisplayString Size(0..12)  

dot1qVlanStaticEgressPorts 1.3.6.1.4.1.24062.2.2.17.5.2.2.1.3
The set of ports which are permanently configured to transmitting traffic for this VLAN as either tagged or untagged frames. Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'. Changes to this object affect the per-port per-VLAN Registrar control for Registration Fixed for the relevant GVRP state machine on each port. A port may not be added in this set if it is already a member of the set of ports in dot1qVlanForbiddenEgressPorts. The default value of this object is a string of zeros, indicating not fixed.
OBJECT-TYPE    
  PortList  

dot1qVlanStaticUntaggedPorts 1.3.6.1.4.1.24062.2.2.17.5.2.2.1.4
The set of ports which are permanently configured to transmitting traffic for this VLAN as untagged frames. Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'. Changes to this object affect the per-port per-VLAN Registrar control for Registration Fixed for the relevant GVRP state machine on each port. The default value of this object for the default VLAN is a portlist including all ports. There is no specified default for other VLANs.
OBJECT-TYPE    
  PortList  

dot1qVlanStaticTaggedPorts 1.3.6.1.4.1.24062.2.2.17.5.2.2.1.5
The set of ports which are permanently configured to transmitting traffic for this VLAN as tagged frames. Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'. Changes to this object affect the per-port per-VLAN Registrar control for Registration Fixed for the relevant GVRP state machine on each port. The default value of this object for the default VLAN is a portlist including all ports. There is no specified default for other VLANs.
OBJECT-TYPE    
  PortList  

dot1qVlanStaticRowStatus 1.3.6.1.4.1.24062.2.2.17.5.2.2.1.6
This object is used to manage to creation and deletion of a VLAN, and is used to indicate the status of this entry. To Creating and activate a VLAN, first select a unused VID for dot1qVlanIndex and then set its dot1qVlanStaticRowStatus to 'createAndGo'. The VLAN will be created in the device without tagged or untagged ports. A default VLAN name is assigned and the status is set to 'active'. To configure tagged and untagged port members of the VLAN, assign appropriate of dot1qVlanStaticTaggedPorts and dot1qVlanStaticUntaggedPorts. A set operation takes effect on the device immediately. To delete a VLAN, select the VID for dot1qVlanIndex and set dot1qVlanStaticRowStatus to 'destory'. The row and the corresponding VLAN configurarion will be removed from the device. VLAN 1 is the default VLAN and can never be deleted. All untagged traffic falls into this VLAN by default. 'createAndWait', 'notInService', 'notReady' have no effects.
OBJECT-TYPE    
  RowStatus  

dot1qGvrp 1.3.6.1.4.1.24062.2.2.17.5.2.3
OBJECT IDENTIFIER    

dot1qGvrpStatus 1.3.6.1.4.1.24062.2.2.17.5.2.3.1
Enable GVRP Protocol.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

dot1qPortGvrpTable 1.3.6.1.4.1.24062.2.2.17.5.2.3.2
A table containing per port control and status information for GVRP configuration in the device.
OBJECT-TYPE    
  SEQUENCE OF  
    Dot1qPortGvrpEntry

dot1qPortGvrpEntry 1.3.6.1.4.1.24062.2.2.17.5.2.3.2.1
Information controlling GVRP configuration for a port on the device.
OBJECT-TYPE    
  Dot1qPortGvrpEntry  

dot1qPortGvrpIndex 1.3.6.1.4.1.24062.2.2.17.5.2.3.2.1.1
The port identifier.
OBJECT-TYPE    
  INTEGER  

dot1qPortGvrpStatus 1.3.6.1.4.1.24062.2.2.17.5.2.3.2.1.2
The state of GVRP operation on this port. The value enabled(1) indicates that GVRP is enabled on this port, as long as dot1qGvrpStatus is also enabled for this device. When disabled(2) but dot1qGvrpStatus is still enabled for the device, GVRP is disabled on this port: any GVRP packets received will be silently discarded and no GVRP registrations will be propagated from other ports. This object affects all GVRP Applicant and Registrar state machines on this port. A transition from disabled(2) to enabled(1) will cause a reset of all GVRP state machines on this port.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

dot1qPortGvrpRegistrationMode 1.3.6.1.4.1.24062.2.2.17.5.2.3.2.1.3
Administrative controls
OBJECT-TYPE    
  INTEGER registrationFixed(1), registrationForbidden(2), registrationNormal(3)  

dot1qPortGarpJoinTimer 1.3.6.1.4.1.24062.2.2.17.5.2.3.2.1.4
The GARP Join timer, in centiseconds.
OBJECT-TYPE    
  TimeInterval  

dot1qPortGarpLeaveTimer 1.3.6.1.4.1.24062.2.2.17.5.2.3.2.1.5
The GARP Leave time, in centiseconds.
OBJECT-TYPE    
  TimeInterval  

dot1qPortGarpLeaveAllTimer 1.3.6.1.4.1.24062.2.2.17.5.2.3.2.1.6
The GARP LeaveAll time, in centiseconds.
OBJECT-TYPE    
  TimeInterval  

dot1qVlanCurrentTable 1.3.6.1.4.1.24062.2.2.17.5.2.4
A table containing information about currently configured VLANs, either by (local or network) management, or dynamically created as a result of GVRP requests received.
OBJECT-TYPE    
  SEQUENCE OF  
    Dot1qVlanCurrentEntry

dot1qVlanCurrentEntry 1.3.6.1.4.1.24062.2.2.17.5.2.4.1
Information for a VLAN configured into the device by (local or network) management, or dynamically created as a result of GVRP requests received.
OBJECT-TYPE    
  Dot1qVlanCurrentEntry  

dot1qVlanCurrentIndex 1.3.6.1.4.1.24062.2.2.17.5.2.4.1.1
The VLAN Identifier (VID) refering to this VLAN.
OBJECT-TYPE    
  INTEGER  

dot1qVlanCurrentEgressPorts 1.3.6.1.4.1.24062.2.2.17.5.2.4.1.2
The set of ports which are transmitting traffic for this VLAN as either tagged or untagged frames.
OBJECT-TYPE    
  PortList  

dot1qVlanCurrentUntaggedPorts 1.3.6.1.4.1.24062.2.2.17.5.2.4.1.3
The set of ports which are transmitting traffic for this VLAN as untagged frames.
OBJECT-TYPE    
  PortList  

dot1qVlanStatus 1.3.6.1.4.1.24062.2.2.17.5.2.4.1.4
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so differ from the following values. permanent(2) - this entry, corresponding to an entry in dot1qVlanStaticTable, is currently in use and will remain so after the next reset of the device. The port lists for this entry include ports from the equivalent dot1qVlanStaticTable entry and ports learnt dynamically. dynamicGvrp(3) - this entry is currently in use and will remain so until removed by GVRP. There is no static entry for this VLAN and it will be removed when the last port leaves the VLAN.
OBJECT-TYPE    
  INTEGER other(1), permanent(2), dynamicGvrp(3)  

dot1qTunnel 1.3.6.1.4.1.24062.2.2.17.5.2.5
OBJECT IDENTIFIER    

dot1qTunnelEtherType 1.3.6.1.4.1.24062.2.2.17.5.2.5.1
ethertype/TPID
OBJECT-TYPE    
  OCTET STRING Size(2)  

dot1qTunnelPortTable 1.3.6.1.4.1.24062.2.2.17.5.2.5.2
A table containing per tunnel access or uplink port information in the device.
OBJECT-TYPE    
  SEQUENCE OF  
    Dot1qTunnelPortEntry

dot1qTunnelPortEntry 1.3.6.1.4.1.24062.2.2.17.5.2.5.2.1
Information controlling tunnel configuration for a port on the device.
OBJECT-TYPE    
  Dot1qTunnelPortEntry  

dot1qTunnelPortIndex 1.3.6.1.4.1.24062.2.2.17.5.2.5.2.1.1
The port identifier.
OBJECT-TYPE    
  INTEGER  

dot1qTunnelPortMode 1.3.6.1.4.1.24062.2.2.17.5.2.5.2.1.2
Tunnel mode controls
OBJECT-TYPE    
  INTEGER normal(1), access(2), uplink(3), uplink-add-pvid(4)  

privateVlan 1.3.6.1.4.1.24062.2.2.17.5.3
OBJECT IDENTIFIER    

privateVlanIdTable 1.3.6.1.4.1.24062.2.2.17.5.3.1
A table containing per Private VLAN ID information in the device.
OBJECT-TYPE    
  SEQUENCE OF  
    PrivateVlanIdEntry

privateVlanIdEntry 1.3.6.1.4.1.24062.2.2.17.5.3.1.1
Information controlling Private VLAN ID configuration on the device.
OBJECT-TYPE    
  PrivateVlanIdEntry  

privateVlanId 1.3.6.1.4.1.24062.2.2.17.5.3.1.1.1
The Private VLAN ID.
OBJECT-TYPE    
  INTEGER  

privateVlanIdType 1.3.6.1.4.1.24062.2.2.17.5.3.1.1.2
Private VLAN ID type controls
OBJECT-TYPE    
  INTEGER normal(1), community(2), isolated(3), primary(4)  

privateVlanPortTable 1.3.6.1.4.1.24062.2.2.17.5.3.2
A table containing per Private VLAN Port information in the device.
OBJECT-TYPE    
  SEQUENCE OF  
    PrivateVlanPortEntry

privateVlanPortEntry 1.3.6.1.4.1.24062.2.2.17.5.3.2.1
Information controlling Private VLAN Port configuration on the device.
OBJECT-TYPE    
  PrivateVlanPortEntry  

privateVlanPortIndex 1.3.6.1.4.1.24062.2.2.17.5.3.2.1.1
The Private Port Index.
OBJECT-TYPE    
  INTEGER  

privateVlanPortMode 1.3.6.1.4.1.24062.2.2.17.5.3.2.1.2
Private VLAN Port mode controls
OBJECT-TYPE    
  INTEGER normal(1), host(2), promiscuous(3)  

privateVlanHostAssociationTable 1.3.6.1.4.1.24062.2.2.17.5.3.3
A table containing per Private VLAN host port association information in the device.
OBJECT-TYPE    
  SEQUENCE OF  
    PrivateVlanHostAssociationEntry

privateVlanHostAssociationEntry 1.3.6.1.4.1.24062.2.2.17.5.3.3.1
Information controlling Private VLAN host port association configuration on the device.
OBJECT-TYPE    
  PrivateVlanHostAssociationEntry  

privateVlanHostAssociationPortIndex 1.3.6.1.4.1.24062.2.2.17.5.3.3.1.1
The Private Host Port Index.
OBJECT-TYPE    
  INTEGER 1..10  

privateVlanHostAssociationPrimaryVid 1.3.6.1.4.1.24062.2.2.17.5.3.3.1.2
Private VLAN host Port association primary VLAN ID. If enter 0 then clear setting.
OBJECT-TYPE    
  INTEGER  

privateVlanHostAssociationSecondaryVid 1.3.6.1.4.1.24062.2.2.17.5.3.3.1.3
Private VLAN host Port association secondary VLAN ID(isolated/community). If enter 0 then clear setting.
OBJECT-TYPE    
  INTEGER  

privateVlanMappingTable 1.3.6.1.4.1.24062.2.2.17.5.3.4
A table containing per Private VLAN promiscuous port mapping information in the device.
OBJECT-TYPE    
  SEQUENCE OF  
    PrivateVlanMappingEntry

privateVlanMappingEntry 1.3.6.1.4.1.24062.2.2.17.5.3.4.1
Information controlling Private VLAN promiscuous port mapping configuration on the device.
OBJECT-TYPE    
  PrivateVlanMappingEntry  

privateVlanMappingPromiscuousPortIndex 1.3.6.1.4.1.24062.2.2.17.5.3.4.1.1
The Private Promiscuous Port Index.
OBJECT-TYPE    
  INTEGER 1..10  

privateVlanMappingPrimaryVid 1.3.6.1.4.1.24062.2.2.17.5.3.4.1.2
Private VLAN promiscuous Port mapping primary VLAN ID. If enter 0 then clear setting.
OBJECT-TYPE    
  INTEGER  

privateVlanMappingSecondaryVidList 1.3.6.1.4.1.24062.2.2.17.5.3.4.1.3
Private VLAN promiscuous Port mapping secondary VLAN ID list. If enter zero-length string then clear setting.
OBJECT-TYPE    
  DisplayString Size(0..64)  

qosPolicy 1.3.6.1.4.1.24062.2.2.17.6.1
(1)8,4,2,1 weight round robin scheme: the switch will follow 8:4:2:1 rate to process priority queue from Hi to lowest queue. This approach prevents the lower priotiry packets from being starved out with only a slight delay to the higher priority packets. (2)Use the strict priority scheme: Queue with higher priority will always be process first, while queue with lower priority will only be processed when the higher priority queue is empty. This approach can cause the lower priorities the be startved out preventing them from transmitting any packets, but it ensures that all high priority packets serviced as soon as possible.
OBJECT-TYPE    
  INTEGER weighteRoundRobin-8-4-2-1(1), strictPriority(2)  

qosPortDefaultCosTable 1.3.6.1.4.1.24062.2.2.17.6.2
Table of descriptive information and configuration about port default cos value.
OBJECT-TYPE    
  SEQUENCE OF  
    QosPortDefaultCosEntry

qosPortDefaultCosEntry 1.3.6.1.4.1.24062.2.2.17.6.2.1
An entry in the table, containing inforamtion about port default cos value.
OBJECT-TYPE    
  QosPortDefaultCosEntry  

qosPortNum 1.3.6.1.4.1.24062.2.2.17.6.2.1.1
Port number.
OBJECT-TYPE    
  Integer32  

qosPortTrust 1.3.6.1.4.1.24062.2.2.17.6.2.1.2
Two kinds of priority information are token into consideration when a packet is processed. One is COS, the IEEE 802.3ac tag containing IEEE 802.1p priority information, and the other is DSCP, the IPv4 Type of Service/DiffServ field. (1)COS only: the port priority will only follow the COS priority that you have assigned. (2)DSCP only: the port priority will only follow the DSCP priority that you have assigned. (3)COS first: the port priority will follow the COS priority first, and then other priority rule. (4)DSCP first: the port priority will follow the DSCP priority first, and the other priority rule.
OBJECT-TYPE    
  Integer32 cos-only(1), dscp-only(2), cos-first(3), dscp-first(4)  

qosPortDefaultCos 1.3.6.1.4.1.24062.2.2.17.6.2.1.3
The port priority will follow the default port priority
OBJECT-TYPE    
  Integer32 0..7  

qosCOSTable 1.3.6.1.4.1.24062.2.2.17.6.3
Table of descriptive information and configuration about COS QOS.
OBJECT-TYPE    
  SEQUENCE OF  
    QosCOSEntry

qosCOSEntry 1.3.6.1.4.1.24062.2.2.17.6.3.1
An entry in the table, containing inforamtion about COS QOS.
OBJECT-TYPE    
  QosCOSEntry  

qosCOSPriority 1.3.6.1.4.1.24062.2.2.17.6.3.1.1
COS priority.
OBJECT-TYPE    
  Integer32 0..7  

qosCOS 1.3.6.1.4.1.24062.2.2.17.6.3.1.2
The port priority will follow the COS priority that you have assigned (0)low, (1)middle, (2)high, or (3)highest.
OBJECT-TYPE    
  INTEGER low(0), middle(1), high(2), highest(3)  

qosDscpTable 1.3.6.1.4.1.24062.2.2.17.6.4
Table of descriptive information and configuration about DSCP QOS.
OBJECT-TYPE    
  SEQUENCE OF  
    QosDscpEntry

qosDscpEntry 1.3.6.1.4.1.24062.2.2.17.6.4.1
An entry in the table, containing inforamtion about DSCP QOS.
OBJECT-TYPE    
  QosDscpEntry  

qosDscpPriority 1.3.6.1.4.1.24062.2.2.17.6.4.1.1
Dscp priority.
OBJECT-TYPE    
  Integer32 0..63  

qosDscp 1.3.6.1.4.1.24062.2.2.17.6.4.1.2
The port priority will follow the Dscp priority that you have assigned (0)low (1)middle, (2)high, (3)highest.
OBJECT-TYPE    
  INTEGER low(0), middle(1), high(2), highest(3)  

igmpQuery 1.3.6.1.4.1.24062.2.2.17.7.1
OBJECT IDENTIFIER    

igmpSnooping 1.3.6.1.4.1.24062.2.2.17.7.2
OBJECT IDENTIFIER    

unknownMulticast 1.3.6.1.4.1.24062.2.2.17.7.3
OBJECT IDENTIFIER    

dot1dGmrp 1.3.6.1.4.1.24062.2.2.17.7.4
OBJECT IDENTIFIER    

igmpQueryVersion 1.3.6.1.4.1.24062.2.2.17.7.1.1
(1)IGMP Query version 1. (2)IGMP Query version 2.
OBJECT-TYPE    
  INTEGER version1(1), version2(2)  

igmpQueryStatus 1.3.6.1.4.1.24062.2.2.17.7.1.2
(1)enable IGMP Query on management vlan. (2)disable IGMP Query.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

igmpQueryInterval 1.3.6.1.4.1.24062.2.2.17.7.1.3
The interval between General Queries sent by this Querier in seconds.
OBJECT-TYPE    
  Integer32 1..65535  

igmpQueryMaxResponseTime 1.3.6.1.4.1.24062.2.2.17.7.1.4
Max Respocse Time is meaningful only in Membership Query messages, and specifies the maximum allowed time before sending a responding report in seconds.
OBJECT-TYPE    
  Integer32 1..25  

igmpSnoopingStatus 1.3.6.1.4.1.24062.2.2.17.7.2.1
Parameter to enable or disable IGMP snooping on the device. When enabled, the device will examine IGMP packets and set up filters for multicast traffic. The Internet Group Management Protocol (IGMP) is an internal protocol of the Internet Protocol (IP) suite. IP manages multicast traffic by using switches, routers, and hosts that support IGMP. Enabling IGMP makes the device to gather multicast group membership information by snooping IGMP packets, which helps the device switch IP multicast traffic to the ports where group members exist instead of flooding the traffic to every ports. IGMP have three fundamental types of message as follows: Message Description -------------------------------------------------------------- Query A message sent from the querier (IGMP router or switch) asking for responses from each host belonging to a multicast group. Report A message sent by a host to the querier to indicate that the host wants to be or is a member of a given group indicated in the report message. Leave A message sent by a host to the querier to indicate that the host has quit to be a member for a specific multicast group. The IGMP snooping functionality is configured on a vlan basis. To enable or disable IGMP snooping on vlans: 1. set igmpSnoopingStatus to enable(1) or disable(2). 2. specify on which vlan IGMP snooping works by configuring each entries in the igmpSnoopingTable. As a result, you can turn on or off IGMP snooping functionality by setting igmpSnoopingStatus while keeping the configuration for each vlan. Or you can turn on or off IGMP snooping for a specific vlan in igmpSnoopingTable with the statuses on other vlan untouched.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

igmpSnoopingTable 1.3.6.1.4.1.24062.2.2.17.7.2.2
Table of descriptive information about on which vlan is IGMP snooping enabled.
OBJECT-TYPE    
  SEQUENCE OF  
    IgmpSnoopingEntry

igmpSnoopingEntry 1.3.6.1.4.1.24062.2.2.17.7.2.2.1
Inforamtion enabling or disabling IGMP snooping on a vlan.
OBJECT-TYPE    
  IgmpSnoopingEntry  

igmpSnoopingEntryVID 1.3.6.1.4.1.24062.2.2.17.7.2.2.1.1
The vlan id.
OBJECT-TYPE    
  INTEGER  

igmpSnoopingEntryStatus 1.3.6.1.4.1.24062.2.2.17.7.2.2.1.2
The state of igmp snooping functionality on a vlan. Set to enabled(1) indicates that igmp snooping is enabled on the vlan. When igmpSnoopingStatus is also turned on, each IGMP packets on the vlan will be processed. When disabled(2) with igmpSnoopingStatus enabled, igmp packets will not be processed and be propagated to other member ports of the vlan. A transition from disabled(2) to enabled(1) will cause a reset of all igmp snooping information on this vlan.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

igmpSnoopingGroupTable 1.3.6.1.4.1.24062.2.2.17.7.2.3
Table of descriptive information about IGMP snooped multicast groups.
OBJECT-TYPE    
  SEQUENCE OF  
    IgmpSnoopingGroupEntry

igmpSnoopingGroupEntry 1.3.6.1.4.1.24062.2.2.17.7.2.3.1
Information containing a multicast group and its member ports.
OBJECT-TYPE    
  IgmpSnoopingGroupEntry  

igmpSnoopingGroupEntryVID 1.3.6.1.4.1.24062.2.2.17.7.2.3.1.1
The VLAN ID of an IGMP entry.
OBJECT-TYPE    
  INTEGER  

igmpSnoopingGroupEntryIPAddr 1.3.6.1.4.1.24062.2.2.17.7.2.3.1.2
The multicast group IP address.
OBJECT-TYPE    
  IpAddress  

igmpSnoopingGroupEntryMembers 1.3.6.1.4.1.24062.2.2.17.7.2.3.1.3
The member ports of the group.
OBJECT-TYPE    
  PortList  

unknownMulticastStatus 1.3.6.1.4.1.24062.2.2.17.7.3.1
Select IGMP Unknown Multicast policy. (1) Send to Query Ports: The device sends the packets with an unknown MAC/IP Multicast address to query ports (2) Discard: The device discards all packets with an unknown MAC/IP Multicast address. (3) Send to All Ports: The device sends the packets with an unknown MAC/IP Multicast address to all ports.
OBJECT-TYPE    
  INTEGER source-only-learning(1), discard(2), flood(3)  

dot1dGmrpStatus 1.3.6.1.4.1.24062.2.2.17.7.4.1
Enable GMRP Protocol.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

dot1dPortGmrpTable 1.3.6.1.4.1.24062.2.2.17.7.4.2
A table containing per port control and status information for GMRP configuration in the device.
OBJECT-TYPE    
  SEQUENCE OF  
    Dot1dPortGmrpEntry

dot1dPortGmrpEntry 1.3.6.1.4.1.24062.2.2.17.7.4.2.1
Information controlling GMRP configuration for a port on the device.
OBJECT-TYPE    
  Dot1dPortGmrpEntry  

dot1dPortGmrpIndex 1.3.6.1.4.1.24062.2.2.17.7.4.2.1.1
The port identifier.
OBJECT-TYPE    
  INTEGER  

dot1dPortGmrpStatus 1.3.6.1.4.1.24062.2.2.17.7.4.2.1.2
The state of GMRP operation on this port. The value enabled(1) indicates that GMRP is enabled on this port, as long as dot1dGmrpStatus is also enabled for this device. When disabled(2) but dot1dGmrpStatus is still enabled for the device, GMRP is disabled on this port: any GMRP packets received will be silently discarded.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

snmpCommunityStringTable 1.3.6.1.4.1.24062.2.2.17.8.1
Table of information configuring community strings of SNMP agent. An SNMP community string is a text string that acts as a password. It is used to authenticate messages that are sent between the management station (the SNMP manager) and the device (the SNMP agent). The community string is included in every packet that is transmitted between the SNMP manager and the SNMP agent. After receiving an SNMP request, the SNMP agent compares the community string in the request to the community strings that are configured for the agent. The requests are valid under these circumstances: - Only SNMP Get and Get-next requests are valid if the community string in the request matches the read-only community. - SNMP Get, Get-next, and Set requests are valid if the community string in the request matches the agent's read-write community. By default, 'public' is the read-only community and 'private' is the read-write community. Total 4 community strings are allowed to configure in the device.
OBJECT-TYPE    
  SEQUENCE OF  
    SnmpCommunityStringEntry

snmpCommunityStringEntry 1.3.6.1.4.1.24062.2.2.17.8.1.1
Inforamtion configuring an community string.
OBJECT-TYPE    
  SnmpCommunityStringEntry  

snmpCommunityStringIndex 1.3.6.1.4.1.24062.2.2.17.8.1.1.1
Index of community string.
OBJECT-TYPE    
  Integer32  

snmpCommunityStringName 1.3.6.1.4.1.24062.2.2.17.8.1.1.2
A community string with maximum 32 characters.
OBJECT-TYPE    
  DisplayString Size(0..32)  

snmpCommunityStringPrivilege 1.3.6.1.4.1.24062.2.2.17.8.1.1.3
The access privilege of the community string.
OBJECT-TYPE    
  INTEGER ro(1), rw(2)  

snmpCommunityStringStatus 1.3.6.1.4.1.24062.2.2.17.8.1.1.4
The status of this entry. Set to (5)createAndWait to create a new entry. A new entry or an active entry can be edited. Once an entry is modified, its status becomes (3)notReady. Set to (1)active to apply the modification to the switch. An entry can be removed by setting to (6)destory.
OBJECT-TYPE    
  RowStatus  

snmpV3UserTable 1.3.6.1.4.1.24062.2.2.17.8.2
Table of descriptive and information about trap servers. A trap server is the recipient of an SNMP trap. The device does not send a trap unless it knows to which station it should send a trap.
OBJECT-TYPE    
  SEQUENCE OF  
    SnmpV3UserEntry

snmpV3UserEntry 1.3.6.1.4.1.24062.2.2.17.8.2.1
An entry in the table, containing inforamtion about a trap server of SNMP agent.
OBJECT-TYPE    
  SnmpV3UserEntry  

snmpV3UserIndex 1.3.6.1.4.1.24062.2.2.17.8.2.1.1
Index of snmp v3 user.
OBJECT-TYPE    
  Integer32  

snmpV3UserName 1.3.6.1.4.1.24062.2.2.17.8.2.1.2
Tok_String
OBJECT-TYPE    
  DisplayString  

snmpV3UserSecurityLevel 1.3.6.1.4.1.24062.2.2.17.8.2.1.3
Specifiy the authentication and privacy level - noauth(1) no authentication and no privacy. - auth(2) enables MD5 or SHA packet authentication. - priv(3) enables MD5 or SHA packet authentication and DES packet encryption.
OBJECT-TYPE    
  INTEGER noauth(1), auth(2), priv(3)  

snmpV3UserAuthProtocol 1.3.6.1.4.1.24062.2.2.17.8.2.1.4
MD5(Message Digest 5) or SHA (Secure Hash Algorithm)
OBJECT-TYPE    
  INTEGER none(1), md5(2), sha(3)  

snmpV3UserAuthPassword 1.3.6.1.4.1.24062.2.2.17.8.2.1.5
Tok_String
OBJECT-TYPE    
  DisplayString  

snmpV3UserDesPassword 1.3.6.1.4.1.24062.2.2.17.8.2.1.6
Tok_String
OBJECT-TYPE    
  DisplayString  

snmpV3UserStatus 1.3.6.1.4.1.24062.2.2.17.8.2.1.7
Tok_String
OBJECT-TYPE    
  RowStatus  

snmpTrapServerEnable 1.3.6.1.4.1.24062.2.2.17.8.3
To enable, disable snmp trap functionality. SNMPv1 traps are defined in RFC 1157, and SNMPv2c trap is defined as NOTIFICATION. SNMP traps enable this device to notify the management station of significant events by way of an unsolicited SNMP message. After the manager receives the event, the manager displays it and can choose to take an action based on the event. For instance, the manager can poll the agent directly, or poll other associated device agents to get a better understanding of the event.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

snmpTrapServerTable 1.3.6.1.4.1.24062.2.2.17.8.4
Table of descriptive and information about trap servers. A trap server is the recipient of an SNMP trap. The device does not send a trap unless it knows to which station it should send a trap.
OBJECT-TYPE    
  SEQUENCE OF  
    SnmpTrapServerEntry

snmpTrapServerEntry 1.3.6.1.4.1.24062.2.2.17.8.4.1
An entry in the table, containing inforamtion about a trap server of SNMP agent.
OBJECT-TYPE    
  SnmpTrapServerEntry  

snmpTrapServerIndex 1.3.6.1.4.1.24062.2.2.17.8.4.1.1
Index of trap server.
OBJECT-TYPE    
  Integer32  

snmpTrapServerIPAddr 1.3.6.1.4.1.24062.2.2.17.8.4.1.2
Trap Server IP Address.
OBJECT-TYPE    
  IpAddress  

snmpTrapServerTrapComm 1.3.6.1.4.1.24062.2.2.17.8.4.1.3
The community string of trap server. The password-like string will be sent with the notification operation.
OBJECT-TYPE    
  DisplayString Size(0..32)  

snmpTrapServerTrapVer 1.3.6.1.4.1.24062.2.2.17.8.4.1.4
The trap version.
OBJECT-TYPE    
  INTEGER v1(1), v2c(2)  

snmpTrapServerStatus 1.3.6.1.4.1.24062.2.2.17.8.4.1.5
The status of this entry. Set to (5)createAndWait to create a new entry. A new entry or an active entry can be edited. Once an entry is modified, its status becomes (3)notReady. Set to (1)active to apply the modification to the device. An entry can be removed by setting to (6)destory.
OBJECT-TYPE    
  RowStatus  

portSecurity 1.3.6.1.4.1.24062.2.2.17.9.1
OBJECT IDENTIFIER    

ipSecurity 1.3.6.1.4.1.24062.2.2.17.9.2
OBJECT IDENTIFIER    

dot1x 1.3.6.1.4.1.24062.2.2.17.9.3
OBJECT IDENTIFIER    

portSecurityStatusTable 1.3.6.1.4.1.24062.2.2.17.9.1.1
A table containing information about port security status on each port. Port security prevents a port from address learning. Only those MAC addresses that are configured by management are allowed to access the switch or transmit/receive through the port. Upto 10 MAC addresses can assigned to each port by adding address entries to portSecurityMacTable or macAddrTable. If the port security functionality is enabled but without any MAC address configured on a port, no traffic can access the switch or transmit/receive from the port.
OBJECT-TYPE    
  SEQUENCE OF  
    PortSecurityStatusEntry

portSecurityStatusEntry 1.3.6.1.4.1.24062.2.2.17.9.1.1.1
An entry configuring port security for a port.
OBJECT-TYPE    
  PortSecurityStatusEntry  

portSecurityPortIndex 1.3.6.1.4.1.24062.2.2.17.9.1.1.1.1
The port id.
OBJECT-TYPE    
  Integer32  

portSecurityPortStatus 1.3.6.1.4.1.24062.2.2.17.9.1.1.1.2
(1)enable port security on this port. (2)disable port security on this port.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

portSecurityMacTable 1.3.6.1.4.1.24062.2.2.17.9.1.2
Table configuring static unicast MAC address for each port. When you add a static MAC address, it remains in the switch's address table, regardless of whether the device is physically connected to the switch. With enabling port security in portSecurityStatusTable, only those MAC addresses configured in portSecurityMacTable are allowed to access the switch or transmit/receive through the port.
OBJECT-TYPE    
  SEQUENCE OF  
    PortSecurityMacEntry

portSecurityMacEntry 1.3.6.1.4.1.24062.2.2.17.9.1.2.1
An entry configuring a static unicast MAC addresses on a port.
OBJECT-TYPE    
  PortSecurityMacEntry  

portSecurityMacIndex 1.3.6.1.4.1.24062.2.2.17.9.1.2.1.1
Index of MAC.
OBJECT-TYPE    
  Integer32  

portSecurityPort 1.3.6.1.4.1.24062.2.2.17.9.1.2.1.2
The port id.
OBJECT-TYPE    
  Integer32  

portSecurityVlanIndex 1.3.6.1.4.1.24062.2.2.17.9.1.2.1.3
The vlan id where the MAC address belongs to.
OBJECT-TYPE    
  Integer32  

portSecurityMac 1.3.6.1.4.1.24062.2.2.17.9.1.2.1.4
MAC address of the entry.
OBJECT-TYPE    
  MacAddress  

portSecurityMacStatus 1.3.6.1.4.1.24062.2.2.17.9.1.2.1.5
The status of this entry. Set to (5)createAndWait to create a new entry. A new entry or an active entry can be edited. Once an entry is modified, its status becomes (3)notReady. Set to (1)active to apply the modification to the device. An entry can be removed by setting to (6)destory.
OBJECT-TYPE    
  RowStatus  

ipSecurityStatus 1.3.6.1.4.1.24062.2.2.17.9.2.1
Enable or disable IP security functionality. IP security allows you to assign specific IP addresses that are permitted to access the device for securing switch management. Set to (1) to enable IP Security. set to (2) to disable IP Security. Enabling IP Security without any entries configured in the ipSecurityTable has no effect on the access traffic.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

ipSecurityTable 1.3.6.1.4.1.24062.2.2.17.9.2.2
Table configuring IP addresses that can access and manage the device through network, such as telnet, web or SNMP. Please note that enabling IP security function but without adding the IP address of your current management station will break current management connection.
OBJECT-TYPE    
  SEQUENCE OF  
    IpSecurityEntry

ipSecurityEntry 1.3.6.1.4.1.24062.2.2.17.9.2.2.1
An entry configuring an security IP address.
OBJECT-TYPE    
  IpSecurityEntry  

ipSecurityIndex 1.3.6.1.4.1.24062.2.2.17.9.2.2.1.1
Index of IP address entry.
OBJECT-TYPE    
  Integer32 1..10  

ipSecurityIP 1.3.6.1.4.1.24062.2.2.17.9.2.2.1.2
An IP address that can access and manage the device.
OBJECT-TYPE    
  IpAddress  

ipSecurityRowStatus 1.3.6.1.4.1.24062.2.2.17.9.2.2.1.3
This object is used to manage to creation and deletion of a authorized IP address, and is used to indicate the status of this entry. A empty entry or an active entry can be edited. Once an entry is modified, its status becomes (3)notReady. Set to (1)active to apply the modification to the device. An entry can be removed by setting to (6)destory.
OBJECT-TYPE    
  RowStatus  

dot1xStatus 1.3.6.1.4.1.24062.2.2.17.9.3.1
IEEE802.1x protocol function status. (1) IEEE802.1x protocol function is enabled. (2) IEEE802.1x protocol function is disabled. 802.1x makes use of the physical access characteristics of IEEE802 LAN infrastructures in order to provide a means of authenticating and authorizing devices attached to a LAN port that has point-to-point connection characteristics, and of preventing access to that port in cases in which the authentication and authorization process fails.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

dot1xAuthentication 1.3.6.1.4.1.24062.2.2.17.9.3.2
.
OBJECT-TYPE    
  INTEGER local(1), radius(2)  

radiusServerTable 1.3.6.1.4.1.24062.2.2.17.9.3.3
.
OBJECT-TYPE    
  SEQUENCE OF  
    RadiusServerEntry

radiusServerEntry 1.3.6.1.4.1.24062.2.2.17.9.3.3.1
.
OBJECT-TYPE    
  RadiusServerEntry  

radiusServerIndex 1.3.6.1.4.1.24062.2.2.17.9.3.3.1.1
Index of Radius server configuration.
OBJECT-TYPE    
  Integer32  

radiusServerIp 1.3.6.1.4.1.24062.2.2.17.9.3.3.1.2
IP address of this radius server.
OBJECT-TYPE    
  IpAddress  

radiusServerServerPort 1.3.6.1.4.1.24062.2.2.17.9.3.3.1.3
The UDP port number used by the authentication server to authenticate.
OBJECT-TYPE    
  Integer32  

radiusServerAccountingPort 1.3.6.1.4.1.24062.2.2.17.9.3.3.1.4
Accounting Port: The UDP port number used by the authentication server to retrieve accounting information.
OBJECT-TYPE    
  Integer32  

radiusServerSharedKey 1.3.6.1.4.1.24062.2.2.17.9.3.3.1.5
A key shared between this switch and authentication server.
OBJECT-TYPE    
  DisplayString  

dot1xLocalUserTable 1.3.6.1.4.1.24062.2.2.17.9.3.4
.
OBJECT-TYPE    
  SEQUENCE OF  
    Dot1xLocalUserEntry

dot1xLocalUserEntry 1.3.6.1.4.1.24062.2.2.17.9.3.4.1
.
OBJECT-TYPE    
  Dot1xLocalUserEntry  

dot1xLocalUserIndex 1.3.6.1.4.1.24062.2.2.17.9.3.4.1.1
.
OBJECT-TYPE    
  Integer32  

dot1xLocalUserName 1.3.6.1.4.1.24062.2.2.17.9.3.4.1.2
set this field to empty to remove this user config.
OBJECT-TYPE    
  DisplayString  

dot1xLocalUserPassword 1.3.6.1.4.1.24062.2.2.17.9.3.4.1.3
.
OBJECT-TYPE    
  DisplayString  

dot1xLocalUserVid 1.3.6.1.4.1.24062.2.2.17.9.3.4.1.4
.
OBJECT-TYPE    
  Integer32  

dot1xPortConfigTable 1.3.6.1.4.1.24062.2.2.17.9.3.5
.
OBJECT-TYPE    
  SEQUENCE OF  
    Dot1xPortConfigEntry

dot1xPortConfigEntry 1.3.6.1.4.1.24062.2.2.17.9.3.5.1
.
OBJECT-TYPE    
  Dot1xPortConfigEntry  

dot1xPortConfigIndex 1.3.6.1.4.1.24062.2.2.17.9.3.5.1.1
.
OBJECT-TYPE    
  Integer32  

dot1xPortAuthControl 1.3.6.1.4.1.24062.2.2.17.9.3.5.1.2
.
OBJECT-TYPE    
  INTEGER auto(1), forceAuthorized(2), forceUnauthorized(3)  

dot1xPortReauthentication 1.3.6.1.4.1.24062.2.2.17.9.3.5.1.3
.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

dot1xPortMaxRequest 1.3.6.1.4.1.24062.2.2.17.9.3.5.1.4
.
OBJECT-TYPE    
  INTEGER  

dot1xPortGuestVlan 1.3.6.1.4.1.24062.2.2.17.9.3.5.1.5
.
OBJECT-TYPE    
  INTEGER  

dot1xPortHostMode 1.3.6.1.4.1.24062.2.2.17.9.3.5.1.6
.
OBJECT-TYPE    
  INTEGER single(1), multiple(2)  

dot1xPortAdminDirection 1.3.6.1.4.1.24062.2.2.17.9.3.5.1.7
.
OBJECT-TYPE    
  INTEGER both(1), in(2)  

dot1xPortConfigSetDefault 1.3.6.1.4.1.24062.2.2.17.9.3.5.1.8
.
OBJECT-TYPE    
  INTEGER apply(1)  

dot1xPortReinitialize 1.3.6.1.4.1.24062.2.2.17.9.3.5.1.9
.
OBJECT-TYPE    
  INTEGER apply(1)  

dot1xPortClientReauth 1.3.6.1.4.1.24062.2.2.17.9.3.5.1.10
.
OBJECT-TYPE    
  INTEGER apply(1)  

dot1xPortTimeoutConfigTable 1.3.6.1.4.1.24062.2.2.17.9.3.6
.
OBJECT-TYPE    
  SEQUENCE OF  
    Dot1xPortTimeoutConfigEntry

dot1xPortTimeoutConfigEntry 1.3.6.1.4.1.24062.2.2.17.9.3.6.1
.
OBJECT-TYPE    
  Dot1xPortTimeoutConfigEntry  

dot1xPortTimeoutIndex 1.3.6.1.4.1.24062.2.2.17.9.3.6.1.1
.
OBJECT-TYPE    
  Integer32  

dot1xPortReauthPeriod 1.3.6.1.4.1.24062.2.2.17.9.3.6.1.2
.
OBJECT-TYPE    
  Integer32  

dot1xPortQuietPeriod 1.3.6.1.4.1.24062.2.2.17.9.3.6.1.3
.
OBJECT-TYPE    
  Integer32  

dot1xPortTxPeriod 1.3.6.1.4.1.24062.2.2.17.9.3.6.1.4
.
OBJECT-TYPE    
  Integer32  

dot1xPortSupplicantTimeout 1.3.6.1.4.1.24062.2.2.17.9.3.6.1.5
.
OBJECT-TYPE    
  Integer32  

dot1xPortServerTimeout 1.3.6.1.4.1.24062.2.2.17.9.3.6.1.6
.
OBJECT-TYPE    
  Integer32  

dot1xPortStatusTable 1.3.6.1.4.1.24062.2.2.17.9.3.7
.
OBJECT-TYPE    
  SEQUENCE OF  
    Dot1xPortStatusEntry

dot1xPortStatusEntry 1.3.6.1.4.1.24062.2.2.17.9.3.7.1
.
OBJECT-TYPE    
  Dot1xPortStatusEntry  

dot1xPortStatusIndex 1.3.6.1.4.1.24062.2.2.17.9.3.7.1.1
.
OBJECT-TYPE    
  Integer32  

dot1xPortCtrl 1.3.6.1.4.1.24062.2.2.17.9.3.7.1.2
.
OBJECT-TYPE    
  INTEGER auto(1), forceAuthorized(2), forceUnauthorized(3)  

dot1xPortAuthStatus 1.3.6.1.4.1.24062.2.2.17.9.3.7.1.3
.
OBJECT-TYPE    
  INTEGER authorized(1), unauthorized(2), none(3)  

dot1xPortAuthSupplicant 1.3.6.1.4.1.24062.2.2.17.9.3.7.1.4
.
OBJECT-TYPE    
  MacAddress  

dot1xPortOperDirection 1.3.6.1.4.1.24062.2.2.17.9.3.7.1.5
.
OBJECT-TYPE    
  INTEGER both(1), in(2)  

faultRelay 1.3.6.1.4.1.24062.2.2.17.10.1
OBJECT IDENTIFIER    

eventAndEmailWarning 1.3.6.1.4.1.24062.2.2.17.10.2
OBJECT IDENTIFIER    

eventSelection 1.3.6.1.4.1.24062.2.2.17.10.2.1
OBJECT IDENTIFIER    

sysLogConfiguration 1.3.6.1.4.1.24062.2.2.17.10.2.2
OBJECT IDENTIFIER    

smtpConfiguration 1.3.6.1.4.1.24062.2.2.17.10.2.3
OBJECT IDENTIFIER    

faultRelayTable 1.3.6.1.4.1.24062.2.2.17.10.1.1
Table of configuration about fault relay. A fault relay is able to control an output circuit which is triggered by management defined fault events. There are two fault relays in the device, each is controlled by an faultRelayEntry in this table. To configure a fault relay, first select the type of fault event which will trigger the relay in faultSelection, and then configure the related column. Set faultRelayEntryStatus to active(1) to set the configuration to the device.
OBJECT-TYPE    
  SEQUENCE OF  
    FaultRelayEntry

faultRelayEntry 1.3.6.1.4.1.24062.2.2.17.10.1.1.1
A entry controlling a fault relay configuration.
OBJECT-TYPE    
  FaultRelayEntry  

faultRelayId 1.3.6.1.4.1.24062.2.2.17.10.1.1.1.1
Index of fault relay.
OBJECT-TYPE    
  INTEGER relay1(1), relay2(2)  

diConfig 1.3.6.1.4.1.24062.2.2.17.10.1.1.1.2
The fault relay will be triggered if digital input is low or high.
OBJECT-TYPE    
  INTEGER di1Low(1), di1High(2), disable(3)  

dryOutputConfig 1.3.6.1.4.1.24062.2.2.17.10.1.1.1.3
The dry output mechanism of fault relay will be enabled or disable.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

dryOutputOnPeriod 1.3.6.1.4.1.24062.2.2.17.10.1.1.1.4
The fault relay will be closed after a period (in seconds). Together with dryOutputOffPeriod, the fault relay can be configured to continue on and off.
OBJECT-TYPE    
  INTEGER  

dryOutputOffPeriod 1.3.6.1.4.1.24062.2.2.17.10.1.1.1.5
The fault relay will be opened after a period (in seconds). Together with dryOutputOnPeriod, the fault relay can be configured to continue on and off.
OBJECT-TYPE    
  INTEGER  

powerFailureConfig 1.3.6.1.4.1.24062.2.2.17.10.1.1.1.6
The fault relay will be triggered if the configured power fails. Any means either power 1 or power2 fails
OBJECT-TYPE    
  INTEGER power1(1), power2(2), any(255), disable(3)  

linkFailureConfig 1.3.6.1.4.1.24062.2.2.17.10.1.1.1.7
The fault relay will be trigger if any of the configured links fails.
OBJECT-TYPE    
  PortList  

pingFailureConfig 1.3.6.1.4.1.24062.2.2.17.10.1.1.1.8
The ping failure mechanism of fault relay will be enabled or disable.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

pingFailureIP 1.3.6.1.4.1.24062.2.2.17.10.1.1.1.9
The fault relay will be trigger if fail to ping the assigned IP address.
OBJECT-TYPE    
  IpAddress  

pingFailureResetTime 1.3.6.1.4.1.24062.2.2.17.10.1.1.1.10
Reset the ping process after pingResetTime, and then wait pingHoldTime to ping again. (optional)
OBJECT-TYPE    
  INTEGER  

pingFailureHoldTime 1.3.6.1.4.1.24062.2.2.17.10.1.1.1.11
Reset the ping process after pingResetTime, and then wait pingHoldTime to ping again. (optional)
OBJECT-TYPE    
  INTEGER  

ringFailureConfig 1.3.6.1.4.1.24062.2.2.17.10.1.1.1.12
The fault relay will be triggered if the configured ring fails.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

systemEventTable 1.3.6.1.4.1.24062.2.2.17.10.2.1.1
Table of descriptive information and controls the reactions to system events. Three types of reactions will be triggered: (1)logging in the switch or send logs to remote syslog servers, (2)sending an email, or (3)send an snmp trap. Each type of alert is configured in sysLogConfiguration, smtpConfiguration, snmpTrapServerEnable and snmpTrapServerTable.
OBJECT-TYPE    
  SEQUENCE OF  
    SystemEventEntry

systemEventEntry 1.3.6.1.4.1.24062.2.2.17.10.2.1.1.1
An entry containing type of system events.
OBJECT-TYPE    
  SystemEventEntry  

eventSystemEventIndex 1.3.6.1.4.1.24062.2.2.17.10.2.1.1.1.1
Index of events.
OBJECT-TYPE    
  Integer32  

eventDeviceColdStartEvent 1.3.6.1.4.1.24062.2.2.17.10.2.1.1.1.2
Select which warning machanism to take place when the device cold starts.
OBJECT-TYPE    
  AlertType  

eventDeviceWarmStartEvent 1.3.6.1.4.1.24062.2.2.17.10.2.1.1.1.3
Select which warning machanism to take place when the device warm starts.
OBJECT-TYPE    
  AlertType  

eventAuthenticationFailureEvent 1.3.6.1.4.1.24062.2.2.17.10.2.1.1.1.4
Select which warning machanism to take place when authentication failure.
OBJECT-TYPE    
  AlertType  

eventRingEvent 1.3.6.1.4.1.24062.2.2.17.10.2.1.1.1.5
Select which warning machanism to take place when ring event occured.
OBJECT-TYPE    
  AlertType  

eventPower1FailureEvent 1.3.6.1.4.1.24062.2.2.17.10.2.1.1.1.6
Select which warning machanism to take place when POWER 1 failure.
OBJECT-TYPE    
  AlertType  

eventPower2FailureEvent 1.3.6.1.4.1.24062.2.2.17.10.2.1.1.1.7
Select which warning machanism to take place when POWER 2 failure.
OBJECT-TYPE    
  AlertType  

eventFaultRelayEvent 1.3.6.1.4.1.24062.2.2.17.10.2.1.1.1.8
Select which warning machanism to take place when a fault relay is triggered.
OBJECT-TYPE    
  AlertType  

eventTimeSynchronizeEvent 1.3.6.1.4.1.24062.2.2.17.10.2.1.1.1.9
Select which warning machanism to take place when time synchronizatonn failed.
OBJECT-TYPE    
  AlertType  

eventDI1ChangeEvent 1.3.6.1.4.1.24062.2.2.17.10.2.1.1.1.10
Select which warning machanism to take place when DI1 changed .
OBJECT-TYPE    
  AlertType  

eventLoopDetectionEvent 1.3.6.1.4.1.24062.2.2.17.10.2.1.1.1.11
Select which warning machanism to take place when loop detection event occured.
OBJECT-TYPE    
  AlertType  

portEventTable 1.3.6.1.4.1.24062.2.2.17.10.2.1.2
Table of descriptive information and controls the reactions to port link up, link down, or both link up and down. Three types of reactions will be triggered: (1)logging in the switch or send logs to remote syslog servers, (2)sending an email, or (3)send an snmp trap. Each type of alert is configured in sysLogConfiguration, smtpConfiguration, snmpTrapServerEnable and snmpTrapServerTable.
OBJECT-TYPE    
  SEQUENCE OF  
    PortEventEntry

portEventEntry 1.3.6.1.4.1.24062.2.2.17.10.2.1.2.1
An entry controlling the type of port events.
OBJECT-TYPE    
  PortEventEntry  

eventPortNumber 1.3.6.1.4.1.24062.2.2.17.10.2.1.2.1.1
Port number.
OBJECT-TYPE    
  Integer32  

eventPortEvent 1.3.6.1.4.1.24062.2.2.17.10.2.1.2.1.2
Select the port event to react to.
OBJECT-TYPE    
  INTEGER linkup(1), linkdown(2), linkupandlinkdown(3), disabled(4)  

sysLogLocalStatus 1.3.6.1.4.1.24062.2.2.17.10.2.2.1
Parameter to configure if the log should to be kept in the device or not.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sysLogRemoteStatus 1.3.6.1.4.1.24062.2.2.17.10.2.2.2
Parameter to configure the log should be sent to a syslog server specified in sysLogServerAddr or not. When disabled or sysLogServerAddr is 0, the device will not send out or record any log.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sysLogServerAddr 1.3.6.1.4.1.24062.2.2.17.10.2.2.3
The IP address of syslog server.
OBJECT-TYPE    
  IpAddress  

eventEmailAlertStatus 1.3.6.1.4.1.24062.2.2.17.10.2.3.1
Parameter to enable the email alert feature, When enabled, the switch will send an email to the address presented in emailAlertRcptTable.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

eventEmailAlertServer 1.3.6.1.4.1.24062.2.2.17.10.2.3.2
The IP address of SMTP server. It can't be modified when eventEmailAlertStatus is disabled.
OBJECT-TYPE    
  IpAddress  

eventEmailAlertAccount 1.3.6.1.4.1.24062.2.2.17.10.2.3.3
The email account for SMTP server. It can't be modified when eventEmailAlertAuthentication is disabled.
OBJECT-TYPE    
  DisplayString Size(0..70)  

eventEmailAlertAuthentication 1.3.6.1.4.1.24062.2.2.17.10.2.3.4
Set to (1)enabled if it needs authentication to connect to the SMTP server. It can't be modified when eventEmailAlertStatus is disabled.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

eventEmailAlertUser 1.3.6.1.4.1.24062.2.2.17.10.2.3.5
The email account for SMTP server. It can't be modified when eventEmailAlertAuthentication is disabled.
OBJECT-TYPE    
  DisplayString Size(0..70)  

eventEmailAlertPassword 1.3.6.1.4.1.24062.2.2.17.10.2.3.6
The password of email account. It can't be modified when eventEmailAlertAuthentication is disabled.
OBJECT-TYPE    
  DisplayString Size(0..36)  

emailAlertRcptTable 1.3.6.1.4.1.24062.2.2.17.10.2.3.7
Table configuring recipient email addresses.
OBJECT-TYPE    
  SEQUENCE OF  
    EmailAlertRcptEntry

emailAlertRcptEntry 1.3.6.1.4.1.24062.2.2.17.10.2.3.7.1
An entry containing recipient email address.
OBJECT-TYPE    
  EmailAlertRcptEntry  

eventEmailAlertRcptIndex 1.3.6.1.4.1.24062.2.2.17.10.2.3.7.1.1
Index of recipient Email address.
OBJECT-TYPE    
  Integer32  

eventEmailAlertRcptEmailAddr 1.3.6.1.4.1.24062.2.2.17.10.2.3.7.1.2
A recipient email address.
OBJECT-TYPE    
  DisplayString Size(0..48)  

macAddressTable 1.3.6.1.4.1.24062.2.2.17.11.1
OBJECT IDENTIFIER    

portStatistic 1.3.6.1.4.1.24062.2.2.17.11.2
OBJECT IDENTIFIER    

portmirroring 1.3.6.1.4.1.24062.2.2.17.11.3
OBJECT IDENTIFIER    

eventLog 1.3.6.1.4.1.24062.2.2.17.11.4
OBJECT IDENTIFIER    

topologyDiscovery 1.3.6.1.4.1.24062.2.2.17.11.5
OBJECT IDENTIFIER    

macAddrTable 1.3.6.1.4.1.24062.2.2.17.11.1.1
A table containing information about unicast or multicast MAC addresses that currently learned, configured by management or IGMP snooping.
OBJECT-TYPE    
  SEQUENCE OF  
    MACAddrEntry

macAddrEntry 1.3.6.1.4.1.24062.2.2.17.11.1.1.1
An entry containing inforamtion about a MAC address entry.
OBJECT-TYPE    
  MACAddrEntry  

macAddressAddr 1.3.6.1.4.1.24062.2.2.17.11.1.1.1.1
MAC address of the entry.
OBJECT-TYPE    
  MacAddress  

macAddressType 1.3.6.1.4.1.24062.2.2.17.11.1.1.1.2
The type of this entry. dynamicUnicast(1) - unicast address that learned from source address of ingress frames. staticUnicast(2) - unicast address that configured by management and will remain so after the next reset of the device. Upto 10 static unicast entries can be configured for each port. managementUnicast(3) - unicast address that configured for management purpose or the MAC address of the device itself. Management unicast entries are read-only. dynamicMulticast(4) - dynamic multicast address that configured by IGMP snooping. These entries are read-only. staticMulticast(5) - multicast address that configured by management and will remain so after the next reset of the device. -- Upto 10 static multicast entries can be configured. managementMulticast(6) - multicast address that configured for management purpose, such as GVRP and so on. These entries are read-only. Management entries are read-only. Dynamic entries can be read and delete. Only static entries are read-create.
OBJECT-TYPE    
  INTEGER dynamicUnicast(1), staticUnicast(2), managementUnicast(3), dynamicMulticast(4), staticMulticast(5), managementMulticast(6)  

macAddressPortList 1.3.6.1.4.1.24062.2.2.17.11.1.1.1.3
The port list, which must be valid when creating a new entry.
OBJECT-TYPE    
  PortList  

macAddressVlanId 1.3.6.1.4.1.24062.2.2.17.11.1.1.1.4
The VLAN where the mac address learned from or configured to.
OBJECT-TYPE    
  Integer32  

macAddressStatus 1.3.6.1.4.1.24062.2.2.17.11.1.1.1.5
This object is used to manage to creation and deletion of a static entry, and is used to indicate the status of an entry. To Creating a static entry, select a unused value of macAddressIndex and set macAddressStatus to 'createAndWait'. A row will then be created with status set to 'notReady' and its macAddressType, macAddressPortList and macAddressVlanId left unspecified. macAddressType, macAddressPortList and macAddressVlanId are mandatory to activate an entry to the device. macAddressStatus remains 'notReady' if any of these three objects are invalid. macAddressStatus will be changed to 'notInService' when the three objects are correctly configured. Set macAddressStatus to 'active' to activate the MAC entry to the device. Static unicast and multicast entries and dynamic unicast entries are removable. To delete a MAC entry, select the macAddressIndex set macAddressStatus to 'destory'. The row and the corresponding MAC address configurarion will be removed from the device. Set macAddressStatus to 'createAndGo', 'notInService', 'notReady' have no effects.
OBJECT-TYPE    
  RowStatus  

macAddrTableClear 1.3.6.1.4.1.24062.2.2.17.11.1.2
Set to clear for cleaning all the dynamic MAC entries in the MAC address table.
OBJECT-TYPE    
  INTEGER clear(1)  

macAddrTableAgingTime 1.3.6.1.4.1.24062.2.2.17.11.1.3
This value determines the interval that an automatic learned MAC address entry remains valid in the forwarding database, since its last access as a source address, before being purged. The value should be times of 15 in seconds. The minimum age time is 15 seconds. The maximum age time is 3825 seconds or almost 64 minutes. if the value is set to 0, the aging function is disabled and all learned address will remain in the database forever.
OBJECT-TYPE    
  INTEGER 0..3825  

switchPortStatTable 1.3.6.1.4.1.24062.2.2.17.11.2.1
Table of descriptive and statistics information about each switch ports.
OBJECT-TYPE    
  SEQUENCE OF  
    SwitchPortStatEntry

switchPortStatClear 1.3.6.1.4.1.24062.2.2.17.11.2.2
Set to clear(1) to clear all information in the statistics table.
OBJECT-TYPE    
  INTEGER clear(1)  

switchPortStatEntry 1.3.6.1.4.1.24062.2.2.17.11.2.1.1
An entry in the table containing descriptive information and statistics of a port.
OBJECT-TYPE    
  SwitchPortStatEntry  

swPortStatIndex 1.3.6.1.4.1.24062.2.2.17.11.2.1.1.1
Index of port statistic table.
OBJECT-TYPE    
  Integer32  

swPortStatType 1.3.6.1.4.1.24062.2.2.17.11.2.1.1.2
Indicates the port type.
OBJECT-TYPE    
  INTEGER hundredBaseTX(1), hundredBaseFX(2), other(3), notPresent(4)  


swPortStatState 1.3.6.1.4.1.24062.2.2.17.11.2.1.1.4
Indicates the port state.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

swPortStatRXGoodPkt 1.3.6.1.4.1.24062.2.2.17.11.2.1.1.5
The count of good frames received, which is the total number of recieved unicast, broadcast, multicast and pause frames.
OBJECT-TYPE    
  Integer32  

swPortStatRXBadPkt 1.3.6.1.4.1.24062.2.2.17.11.2.1.1.6
The count of bad frames received, which is the total number of undersize, fragment, oversize, jabber, RXErr and FCSErr frames.
OBJECT-TYPE    
  Integer32  

swPortStatRXAbortPkt 1.3.6.1.4.1.24062.2.2.17.11.2.1.1.7
The count of abort frames when receive, which is the total number of discarded and filtered frames.
OBJECT-TYPE    
  Integer32  

swPortStatTXGoodPkt 1.3.6.1.4.1.24062.2.2.17.11.2.1.1.8
The count of good frames transmitted, which is the total number of transmitted unicast, broadcast, multicast and pause frames.
OBJECT-TYPE    
  Integer32  

swPortStatTXBadPkt 1.3.6.1.4.1.24062.2.2.17.11.2.1.1.9
The count of FCSErr frames when transmit.
OBJECT-TYPE    
  Integer32  

swPortStatPacketCollision 1.3.6.1.4.1.24062.2.2.17.11.2.1.1.10
The count of collision.
OBJECT-TYPE    
  Integer32  

portMirrorStatus 1.3.6.1.4.1.24062.2.2.17.11.3.1
To enable or disable port mirroring. Port mirroring is used to send a copy of inbound or outbound network packets seen on one port to another switch port. Administrators may utilized this mechanism to monitor network traffic as well as the performance of a switch.
OBJECT-TYPE    
  Integer32 enable(1), disable(2)  

portMirrorDestinationPortTX 1.3.6.1.4.1.24062.2.2.17.11.3.2
The TX destination port (sniffer port). Destination port can be used to see all monitor port traffic. You can connect sniffer port to a LAN analysier or netxray. Set to 0 to clear the configuration. A destination port can not be the same as a source port. This object can not be modified if portMirrorStatus is disable.
OBJECT-TYPE    
  Integer32 0..10  

portMirrorDestinationPortRX 1.3.6.1.4.1.24062.2.2.17.11.3.3
The RX destination port (sniffer port). Destination port can be used to see all monitor port traffic. You can connect sniffer port to a LAN analysier or netxray. Set to 0 to clear the configuration. A destination port can not be the same as a source port. This object can not be modified if portMirrorStatus is disable.
OBJECT-TYPE    
  Integer32 0..10  

portMirrorSourceTable 1.3.6.1.4.1.24062.2.2.17.11.3.4
Table of descriptive information and configuration of port mirroring in this system. Use this table to select monitor port for this switch.
OBJECT-TYPE    
  SEQUENCE OF  
    PortMirrorSourceEntry

portMirrorSourceEntry 1.3.6.1.4.1.24062.2.2.17.11.3.4.1
Information configuring port mirroring on each port.
OBJECT-TYPE    
  PortMirrorSourceEntry  

portMirrorPortNum 1.3.6.1.4.1.24062.2.2.17.11.3.4.1.1
The Port number.
OBJECT-TYPE    
  Integer32 1..10  

portMirrorSourcePort 1.3.6.1.4.1.24062.2.2.17.11.3.4.1.2
The mode of source port (monitor port). (1) TX only. (2) RX only. (3) RX and TX. (4) Source port is disabled. The ports you want to monitor. All source port traffic will be copied to destination port (sniffer port). This object can not be modified if portMirrorStatus is disable.
OBJECT-TYPE    
  INTEGER txOnly(1), rxOnly(2), rxAndTx(3), disabled(4)  

eventLogTable 1.3.6.1.4.1.24062.2.2.17.11.4.1
Table of descriptive information about logs.
OBJECT-TYPE    
  SEQUENCE OF  
    EventLogEntry

eventLogEntry 1.3.6.1.4.1.24062.2.2.17.11.4.1.1
An entry in the table containing a log.
OBJECT-TYPE    
  EventLogEntry  

eventLogIndex 1.3.6.1.4.1.24062.2.2.17.11.4.1.1.1
Index of log.
OBJECT-TYPE    
  Integer32  

eventLogDescription 1.3.6.1.4.1.24062.2.2.17.11.4.1.1.2
The description of a log.
OBJECT-TYPE    
  DisplayString Size(0..100)  

lldpRun 1.3.6.1.4.1.24062.2.2.17.11.5.1
LLDP Enable/Disable
OBJECT-TYPE    
  Integer32 enable(1), disable(2)  

lldpTimer 1.3.6.1.4.1.24062.2.2.17.11.5.2
The transmission frequency of LLDP in seconds
OBJECT-TYPE    
  INTEGER  

lldpHoldTime 1.3.6.1.4.1.24062.2.2.17.11.5.3
The transmission frequency of LLDP in seconds
OBJECT-TYPE    
  INTEGER  

lldpNeighborTable 1.3.6.1.4.1.24062.2.2.17.11.5.4
A table containing LLDP neighbors information
OBJECT-TYPE    
  SEQUENCE OF  
    LldpNeighborEntry

lldpNeighborEntry 1.3.6.1.4.1.24062.2.2.17.11.5.4.1
An entry containing inforamtion about a LLDP neighbor entry.
OBJECT-TYPE    
  LldpNeighborEntry  

lldpNeighborLocalPort 1.3.6.1.4.1.24062.2.2.17.11.5.4.1.1
Local port of LLDP Neighbor
OBJECT-TYPE    
  DisplayString Size(0..31)  

lldpNeighborMacAddress 1.3.6.1.4.1.24062.2.2.17.11.5.4.1.2
MAC address of LLDP Neighbor
OBJECT-TYPE    
  MacAddress  

lldpNeighborIpAddress 1.3.6.1.4.1.24062.2.2.17.11.5.4.1.3
IP address of LLDP Neighbor
OBJECT-TYPE    
  IpAddress  

lldpNeighborVID 1.3.6.1.4.1.24062.2.2.17.11.5.4.1.4
VLAN ID of LLDP Neighbor
OBJECT-TYPE    
  INTEGER  

lldpNeighborTTL 1.3.6.1.4.1.24062.2.2.17.11.5.4.1.5
TTL of LLDP Neighbor
OBJECT-TYPE    
  INTEGER  

saveCfgMgtAction 1.3.6.1.4.1.24062.2.2.17.12.1
Setting this object to active(1) saves current configuration. Setting this object to notActive(2) has no effect. The system always returns the value notActive(2) when this object is read.
OBJECT-TYPE    
  INTEGER active(1), notActive(2)