ITOUCH-INTERNET-MIB

File: ITOUCH-INTERNET-MIB.mib (336137 bytes)

Imported modules

RFC1155-SMI RFC1213-MIB RFC-1212
ITOUCH-MIB

Imported symbols

Counter Gauge IpAddress
DisplayString ifIndex ipNetToMediaNetAddress
ipAdEntAddr OBJECT-TYPE iTouch
DateTime AddressType TypedAddress

Defined Types

IpGenAdExtEntry  
SEQUENCE    
  ipGenAdEntExtType INTEGER
  ipGenAdEntExtBroadcast IpAddress

TcpPortEntry  
SEQUENCE    
  tcpPortIndex INTEGER
  tcpPortConnectByAddress INTEGER
  tcpPortWindowSize INTEGER
  tcpPortKeepAliveLimit INTEGER

GetClientEntry  
SEQUENCE    
  getClientIndex INTEGER
  getClientEntryStatus INTEGER
  getClientAddressType AddressType
  getClientAddress OCTET STRING

SetClientEntry  
SEQUENCE    
  setClientIndex INTEGER
  setClientEntryStatus INTEGER
  setClientAddressType AddressType
  setClientAddress OCTET STRING

TrapClientEntry  
SEQUENCE    
  trapClientIndex INTEGER
  trapClientEntryStatus INTEGER
  trapClientAddressType AddressType
  trapClientAddress OCTET STRING

NameEntry  
SEQUENCE    
  nameName DisplayString
  nameAddress IpAddress
  nameStatus INTEGER
  nameSource INTEGER
  nameTtl INTEGER

SlipEntry  
SEQUENCE    
  slipIndex INTEGER
  slipState INTEGER
  slipLocalAddress IpAddress
  slipRemoteAddress IpAddress
  slipMask IpAddress
  slipPortPacketsReceived Counter
  slipPortPacketsSent Counter
  slipPortPacketsDiscarded Counter
  slipPortPacketLengthErrors Counter
  slipPortPacketChecksumErrors Counter
  slipNetworkPacketsReceived Counter
  slipNetworkPacketsSent Counter
  slipNetworkPacketsDiscarded Counter

TelnetPortEntry  
SEQUENCE    
  telnetPortIndex INTEGER
  telnetPortIncomingTcpPort INTEGER
  telnetPortOutgoingTcpPort INTEGER
  telnetPortNewlineTranslation INTEGER
  telnetPortTerminalType DisplayString
  telnetPortEorReflection INTEGER
  telnetPortBinaryMode INTEGER
  telnetPortSendLocation INTEGER
  telnetPortClientLocation DisplayString
  telnetPortPassiveSendLocation INTEGER

TelnetSerialPortEntry  
SEQUENCE    
  telnetSerialPortIndex INTEGER
  telnetSerialPortOptionDisplay INTEGER
  telnetSerialPortCsiEscape INTEGER
  telnetSerialPortEchoMode INTEGER
  telnetSerialPortNewlineMode INTEGER
  telnetSerialPortTransmitMode INTEGER
  telnetSerialPortTransmitCharacterTimes INTEGER
  telnetSerialPortAbortOutputCharacter INTEGER
  telnetSerialPortAttentionCharacter INTEGER
  telnetSerialPortEraseKeyCharacter INTEGER
  telnetSerialPortEraseLineCharacter INTEGER
  telnetSerialPortInterruptCharacter INTEGER
  telnetSerialPortQueryCharacter INTEGER
  telnetSerialPortSynchronizeCharacter INTEGER
  telnetSerialPortUrgentBreak INTEGER
  telnetSerialPortRs491 INTEGER
  telnetSerialPortTransmitBufferedTime INTEGER
  telnetSerialPortInterpretInterruptAsBreak INTEGER
  telnetSerialPortPass8d INTEGER
  telnetSerialPortComControlClient INTEGER
  telnetSerialPortComControlServer INTEGER
  telnetSerialPortComControlServerRaisesDtr INTEGER
  telnetSerialPortComControlClientTogglesDtr INTEGER

Tn3270DeviceEntry  
SEQUENCE    
  tn3270DeviceName DisplayString
  tn3270DeviceStatus INTEGER
  tn3270DeviceType DisplayString
  tn3270Device3278Model INTEGER
  tn3270DeviceKeyNumber INTEGER
  tn3270DeviceScreenNumber INTEGER

Tn3270KeyEntry  
SEQUENCE    
  tn3270KeyDeviceName DisplayString
  tn3270KeyName INTEGER
  tn3270KeyStatus INTEGER
  tn3270KeyCharacterSequence OCTET STRING
  tn3270KeyDescription DisplayString

Tn3270ScreenEntry  
SEQUENCE    
  tn3270ScreenDeviceName DisplayString
  tn3270ScreenActionName INTEGER
  tn3270ScreenStatus INTEGER
  tn3270ScreenCharacterSequence OCTET STRING

Tn3270LanguageEntry  
SEQUENCE    
  tn3270LanguageName DisplayString
  tn3270LanguageStatus INTEGER

EToALanguageEntry  
SEQUENCE    
  eToALanguageName DisplayString
  eToAOffset INTEGER
  eToAValue INTEGER

AToELanguageEntry  
SEQUENCE    
  aToELanguageName DisplayString
  aToEOffset INTEGER
  aToEValue INTEGER

Tn3270PortEntry  
SEQUENCE    
  tn3270PortIndex INTEGER
  tn3270PortDeviceName DisplayString
  tn3270PortLanguageName DisplayString
  tn3270PortExtendedAttributes INTEGER
  tn3270PortEorNegotiation INTEGER
  tn3270PortErrorLock INTEGER
  tn3270PortPrinterPort INTEGER
  tn3270PortOutgoingTcpPort INTEGER
  tn3270PortSpaceInsert INTEGER
  tn3270PortTypeAhead INTEGER
  tn3270PrefixKeyMap INTEGER
  tn3270PortScanner INTEGER

KerbPortEntry  
SEQUENCE    
  kerbPortIndex INTEGER
  kerbPortStatus INTEGER

PsPortEntry  
SEQUENCE    
  psPortIndex INTEGER
  psPortDefaultInboundAccess INTEGER
  psPortDefaultOutboundAccess INTEGER
  psClrInternetSecurity INTEGER

PsEntry  
SEQUENCE    
  psEntryIndex INTEGER
  psEntryStatus INTEGER
  psEntryAddress IpAddress
  psEntryMask IpAddress
  psEntryAccess INTEGER
  psEntryDirection INTEGER
  psEntryPortMap OCTET STRING

XremotePortEntry  
SEQUENCE    
  xremotePortIndex INTEGER
  xremotePortXremote INTEGER
  xremotePortXdmQuery INTEGER
  xremotePortXdmHost DisplayString

RotaryEntry  
SEQUENCE    
  rotaryAddress IpAddress
  rotaryStatus INTEGER
  rotaryPortMap OCTET STRING

EgpNbrEntry  
SEQUENCE    
  egpNbrAddr IpAddress
  egpNbrIntervalDead INTEGER
  egpNbrStatus INTEGER

OspfIfMtrcEntry  
SEQUENCE    
  ospfIfMtrcIpAddress IpAddress
  ospfIfMtrcAddressLessIf INTEGER
  ospfIfMtrcTos INTEGER
  ospfIfMtrcCostActual INTEGER

OspfXIfEntry  
SEQUENCE    
  ospfXIfIpAddress IpAddress
  ospfXIfAddressLessIf INTEGER
  ospfXIfTypeActual INTEGER
  ospfXIfStatus INTEGER

OspfXAreaEntry  
SEQUENCE    
  ospfXAreaId IpAddress
  ospfXAreaStatus INTEGER

IpAdExtEntry  
SEQUENCE    
  ipAdEntExtAddress IpAddress
  ipAdEntExtProxyArp INTEGER
  ipAdEntExtRip INTEGER

IpRouterIfEntry  
SEQUENCE    
  ipRouterIfIndex INTEGER
  ipRouterIfProtocolPriority INTEGER
  ipRouterIfMTU INTEGER
  ipRouterIfRDP INTEGER
  ipRouterIfArpPacketsIn Counter
  ipRouterIfArpPacketsOut Counter
  ipRouterIfPacketsIn Counter
  ipRouterIfPacketsOut Counter
  ipRouterIfForwardsIn Counter
  ipRouterIfForwardsOut Counter

IpTrafficEntry  
SEQUENCE    
  ipTrafficIndex INTEGER
  ipTrafficPercent INTEGER
  ipTrafficDstAddr IpAddress
  ipTrafficSrcAddr IpAddress
  ipTrafficProtocol INTEGER
  ipTrafficDstPort INTEGER
  ipTrafficSrcPort INTEGER
  ipTrafficIf INTEGER

XIpNetToMediaEntry  
SEQUENCE    
  xIpNetToMediaCircuit INTEGER
  xIpNetToMediaReverseArp INTEGER

UdpBcstServerEntry  
SEQUENCE    
  udpBcstServerAddress IpAddress
  udpBcstServerStatus INTEGER

UdpBcstPortEntry  
SEQUENCE    
  udpBcstPort INTEGER
  udpBcstPortStatus INTEGER

ImpEgpRuleEntry  
SEQUENCE    
  impEgpRuleAs INTEGER
  impEgpRuleNetwork IpAddress
  impEgpRuleAction INTEGER
  impEgpRulePreference INTEGER
  impEgpRuleType INTEGER
  impEgpRuleMetricAction INTEGER
  impEgpRuleMetric INTEGER
  impEgpRuleStatus INTEGER

ImpOspfRuleEntry  
SEQUENCE    
  impOspfRuleNetwork IpAddress
  impOspfRulePreference INTEGER
  impOspfRuleStatus INTEGER

ImpRipRuleEntry  
SEQUENCE    
  impRipRuleFromIf IpAddress
  impRipRuleNetwork IpAddress
  impRipRuleAction INTEGER
  impRipRulePreference INTEGER
  impRipRuleType INTEGER
  impRipRuleMetricAction INTEGER
  impRipRuleMetric INTEGER
  impRipRuleStatus INTEGER

ImpIsisRuleEntry  
SEQUENCE    
  impIsisRuleNetwork IpAddress
  impIsisRuleAction INTEGER
  impIsisRulePreference INTEGER
  impIsisRuleType INTEGER
  impIsisRuleMetricAction INTEGER
  impIsisRuleMetric INTEGER
  impIsisRuleStatus INTEGER

ExpEgpToEgpRuleEntry  
SEQUENCE    
  expEgpToEgpRuleToAs INTEGER
  expEgpToEgpRuleNetwork IpAddress
  expEgpToEgpRuleFromAs INTEGER
  expEgpToEgpRuleAction INTEGER
  expEgpToEgpRuleMetricAction INTEGER
  expEgpToEgpRuleMetric INTEGER
  expEgpToEgpRuleStatus INTEGER

ExpOspfToEgpRuleEntry  
SEQUENCE    
  expOspfToEgpRuleToAs INTEGER
  expOspfToEgpRuleNetwork IpAddress
  expOspfToEgpRuleFromAs INTEGER
  expOspfToEgpRuleAction INTEGER
  expOspfToEgpRuleMetricAction INTEGER
  expOspfToEgpRuleMetric INTEGER
  expOspfToEgpRuleStatus INTEGER

ExpStaticToEgpRuleEntry  
SEQUENCE    
  expStaticToEgpRuleToAs INTEGER
  expStaticToEgpRuleNetwork IpAddress
  expStaticToEgpRuleAction INTEGER
  expStaticToEgpRuleMetricAction INTEGER
  expStaticToEgpRuleMetric INTEGER
  expStaticToEgpRuleStatus INTEGER

ExpEgpToOspfRuleEntry  
SEQUENCE    
  expEgpToOspfRuleNetwork IpAddress
  expEgpToOspfRuleFromAs INTEGER
  expEgpToOspfRuleAction INTEGER
  expEgpToOspfRuleStatus INTEGER

ExpRipToEgpRuleEntry  
SEQUENCE    
  expRipToEgpRuleToAs INTEGER
  expRipToEgpRuleNetwork IpAddress
  expRipToEgpRuleAction INTEGER
  expRipToEgpRuleMetricAction INTEGER
  expRipToEgpRuleMetric INTEGER
  expRipToEgpRuleStatus INTEGER

ExpRipToOspfRuleEntry  
SEQUENCE    
  expRipToOspfRuleNetwork IpAddress
  expRipToOspfRuleAction INTEGER
  expRipToOspfRuleStatus INTEGER

ExpEgpToRipRuleEntry  
SEQUENCE    
  expEgpToRipRuleToIf IpAddress
  expEgpToRipRuleNetwork IpAddress
  expEgpToRipRuleFromAs INTEGER
  expEgpToRipRuleAction INTEGER
  expEgpToRipRuleMetricAction INTEGER
  expEgpToRipRuleMetric INTEGER
  expEgpToRipRuleStatus INTEGER

ExpOspfToRipRuleEntry  
SEQUENCE    
  expOspfToRipRuleToIf IpAddress
  expOspfToRipRuleNetwork IpAddress
  expOspfToRipRuleFromAs INTEGER
  expOspfToRipRuleAction INTEGER
  expOspfToRipRuleMetricAction INTEGER
  expOspfToRipRuleMetric INTEGER
  expOspfToRipRuleStatus INTEGER

ExpRipToRipRuleEntry  
SEQUENCE    
  expRipToRipRuleToIf IpAddress
  expRipToRipRuleNetwork IpAddress
  expRipToRipRuleAction INTEGER
  expRipToRipRuleMetricAction INTEGER
  expRipToRipRuleMetric INTEGER
  expRipToRipRuleStatus INTEGER

ExpStaticToRipRuleEntry  
SEQUENCE    
  expStaticToRipRuleToIf IpAddress
  expStaticToRipRuleNetwork IpAddress
  expStaticToRipRuleAction INTEGER
  expStaticToRipRuleMetricAction INTEGER
  expStaticToRipRuleMetric INTEGER
  expStaticToRipRuleStatus INTEGER

ExpIsisToEgpRuleEntry  
SEQUENCE    
  expIsisToEgpRuleToAs INTEGER
  expIsisToEgpRuleNetwork IpAddress
  expIsisToEgpRuleAction INTEGER
  expIsisToEgpRuleMetricAction INTEGER
  expIsisToEgpRuleMetric INTEGER
  expIsisToEgpRuleStatus INTEGER

ExpIsisToOspfRuleEntry  
SEQUENCE    
  expIsisToOspfRuleNetwork IpAddress
  expIsisToOspfRuleAction INTEGER
  expIsisToOspfRuleStatus INTEGER

ExpIsisToRipRuleEntry  
SEQUENCE    
  expIsisToRipRuleToIf IpAddress
  expIsisToRipRuleNetwork IpAddress
  expIsisToRipRuleAction INTEGER
  expIsisToRipRuleMetricAction INTEGER
  expIsisToRipRuleMetric INTEGER
  expIsisToRipRuleStatus INTEGER

ExpEgpToIsisRuleEntry  
SEQUENCE    
  expEgpToIsisRuleNetwork IpAddress
  expEgpToIsisRuleFromAs INTEGER
  expEgpToIsisRuleAction INTEGER
  expEgpToIsisRuleMetricType INTEGER
  expEgpToIsisRuleDefaultMetricAction INTEGER
  expEgpToIsisRuleDefaultMetric INTEGER
  expEgpToIsisRuleDelayMetricAction INTEGER
  expEgpToIsisRuleDelayMetric INTEGER
  expEgpToIsisRuleErrorMetricAction INTEGER
  expEgpToIsisRuleErrorMetric INTEGER
  expEgpToIsisRuleExpenseMetricAction INTEGER
  expEgpToIsisRuleExpenseMetric INTEGER
  expEgpToIsisRuleStatus INTEGER

ExpOspfToIsisRuleEntry  
SEQUENCE    
  expOspfToIsisRuleNetwork IpAddress
  expOspfToIsisRuleFromAs INTEGER
  expOspfToIsisRuleAction INTEGER
  expOspfToIsisRuleMetricType INTEGER
  expOspfToIsisRuleDefaultMetricAction INTEGER
  expOspfToIsisRuleDefaultMetric INTEGER
  expOspfToIsisRuleDelayMetricAction INTEGER
  expOspfToIsisRuleDelayMetric INTEGER
  expOspfToIsisRuleErrorMetricAction INTEGER
  expOspfToIsisRuleErrorMetric INTEGER
  expOspfToIsisRuleExpenseMetricAction INTEGER
  expOspfToIsisRuleExpenseMetric INTEGER
  expOspfToIsisRuleStatus INTEGER

ExpRipToIsisRuleEntry  
SEQUENCE    
  expRipToIsisRuleNetwork IpAddress
  expRipToIsisRuleAction INTEGER
  expRipToIsisRuleMetricType INTEGER
  expRipToIsisRuleDefaultMetricAction INTEGER
  expRipToIsisRuleDefaultMetric INTEGER
  expRipToIsisRuleDelayMetricAction INTEGER
  expRipToIsisRuleDelayMetric INTEGER
  expRipToIsisRuleErrorMetricAction INTEGER
  expRipToIsisRuleErrorMetric INTEGER
  expRipToIsisRuleExpenseMetricAction INTEGER
  expRipToIsisRuleExpenseMetric INTEGER
  expRipToIsisRuleStatus INTEGER

ExpStaticToIsisRuleEntry  
SEQUENCE    
  expStaticToIsisRuleNetwork IpAddress
  expStaticToIsisRuleAction INTEGER
  expStaticToIsisRuleMetricType INTEGER
  expStaticToIsisRuleDefaultMetricAction INTEGER
  expStaticToIsisRuleDefaultMetric INTEGER
  expStaticToIsisRuleDelayMetricAction INTEGER
  expStaticToIsisRuleDelayMetric INTEGER
  expStaticToIsisRuleErrorMetricAction INTEGER
  expStaticToIsisRuleErrorMetric INTEGER
  expStaticToIsisRuleExpenseMetricAction INTEGER
  expStaticToIsisRuleExpenseMetric INTEGER
  expStaticToIsisRuleStatus INTEGER

IpIfFilterEntry  
SEQUENCE    
  ipIfFilterIndex INTEGER
  ipIfFilterDstAddr IpAddress
  ipIfFilterDstMask IpAddress
  ipIfFilterSrcAddr IpAddress
  ipIfFilterSrcMask IpAddress
  ipIfFilterProtocol INTEGER
  ipIfFilterDstPort INTEGER
  ipIfFilterSrcPort INTEGER
  ipIfFilterAction INTEGER
  ipIfFilterStatus INTEGER

IpIfFilter2Entry  
SEQUENCE    
  ipIfFilter2Index INTEGER
  ipIfFilter2DstAddr IpAddress
  ipIfFilter2DstMask IpAddress
  ipIfFilter2SrcAddr IpAddress
  ipIfFilter2SrcMask IpAddress
  ipIfFilter2Protocol INTEGER
  ipIfFilter2DstPortStart INTEGER
  ipIfFilter2SrcPortStart INTEGER
  ipIfFilter2Action INTEGER
  ipIfFilter2Status INTEGER
  ipIfFilter2DstPortEnd INTEGER
  ipIfFilter2SrcPortEnd INTEGER
  ipIfFilter2TcpSyn INTEGER
  ipIfFilter2ProtocolPriority INTEGER

RipNetEntry  
SEQUENCE    
  ripNetNet IpAddress
  ripNetState INTEGER
  ripNetRipsIn Counter
  ripNetRipsOut Counter
  ripNetAlgorithm INTEGER

LpdQueueEntry  
SEQUENCE    
  lpdQueueStatus INTEGER
  lpdQueueName DisplayString
  lpdQueuePorts OCTET STRING
  lpdQueueEnabled INTEGER
  lpdQueueLfConversion INTEGER
  lpdQueueTotalJobs Gauge
  lpdQueueActiveJobs Gauge
  lpdQueueWaitingJobs Gauge
  lpdQueueProcessedJobs Counter
  lpdQueueFormFeed INTEGER
  lpdQueueBypass INTEGER

LpdJobEntry  
SEQUENCE    
  lpdJobStatus INTEGER
  lpdJobNumber INTEGER
  lpdJobAssignedPort INTEGER
  lpdJobFileSize INTEGER
  lpdJobHostName DisplayString
  lpdJobFileName DisplayString
  lpdJobState INTEGER

SecurIDPortEntry  
SEQUENCE    
  securIDPortIndex INTEGER
  securIDPortStatus INTEGER

SshPortEntry  
SEQUENCE    
  sshPortIndex INTEGER
  sshPortIncomingTcpPort INTEGER
  sshPortNewlineFiltering INTEGER
  sshPortNewline INTEGER
  sshPortTransmitBufferedTime INTEGER
  sshPortRemoteProtocol INTEGER

Defined Values

xInternetDep 1.3.6.1.4.1.33.4
OBJECT IDENTIFIER    

xInternet 1.3.6.1.4.1.33.10
OBJECT IDENTIFIER    

xIp 1.3.6.1.4.1.33.10.1
OBJECT IDENTIFIER    

xTcp 1.3.6.1.4.1.33.10.2
OBJECT IDENTIFIER    

xSnmpAgent 1.3.6.1.4.1.33.10.3
OBJECT IDENTIFIER    

xDomainResolver 1.3.6.1.4.1.33.10.4
OBJECT IDENTIFIER    

xSlip 1.3.6.1.4.1.33.10.5
OBJECT IDENTIFIER    

xTelnet 1.3.6.1.4.1.33.10.6
OBJECT IDENTIFIER    

xTn3270 1.3.6.1.4.1.33.10.7
OBJECT IDENTIFIER    

xKerberos 1.3.6.1.4.1.33.10.8
OBJECT IDENTIFIER    

xPortSecurity 1.3.6.1.4.1.33.10.9
OBJECT IDENTIFIER    

xXremote 1.3.6.1.4.1.33.10.10
OBJECT IDENTIFIER    

xRotary 1.3.6.1.4.1.33.10.11
OBJECT IDENTIFIER    

xEgp 1.3.6.1.4.1.33.10.12
OBJECT IDENTIFIER    

xOspf 1.3.6.1.4.1.33.10.13
OBJECT IDENTIFIER    

xRouterIp 1.3.6.1.4.1.33.10.14
OBJECT IDENTIFIER    

xRouterUdp 1.3.6.1.4.1.33.10.15
OBJECT IDENTIFIER    

xRouterPolicy 1.3.6.1.4.1.33.10.16
OBJECT IDENTIFIER    

xRip 1.3.6.1.4.1.33.10.18
OBJECT IDENTIFIER    

xlpd 1.3.6.1.4.1.33.10.19
OBJECT IDENTIFIER    

xSecurID 1.3.6.1.4.1.33.10.20
OBJECT IDENTIFIER    

xSsh 1.3.6.1.4.1.33.10.23
OBJECT IDENTIFIER    

ipGatewayAddress1 1.3.6.1.4.1.33.10.1.1
The internet address of the system's primary (first choice) gateway. A value of 0.0.0.0 indicates no address. Corresponds directly to SERVER INTERNET PRIMARY GATEWAY ADDRESS and the value labeled 'Primary Gateway Address:' in the SERVER INTERNET CHARACTERISTICS display.
OBJECT-TYPE    
  IpAddress  

ipGatewayAddress2 1.3.6.1.4.1.33.10.1.2
The internet address of the system's secondary (second choice) gateway. A value of 0.0.0.0 indicates no address. Corresponds directly to SERVER INTERNET SECONDARY GATEWAY ADDRESS and the value labeled 'Secondary Gateway Address:' in the SERVER INTERNET CHARACTERISTICS display.
OBJECT-TYPE    
  IpAddress  

ipAutoSubnetMask 1.3.6.1.4.1.33.10.1.3
A control for automatic determination of subnet mask. 'disabled' indicates the system must use the mask as configured by the network manager. 'enabled' indicates that the system is to automatically change the subnet mask when the system's Internet address is changed. Corresponds directly to SERVER INTERNET SUBNET MASK AUTOCONFIGURE and the value labeled 'Subnet Mask Autoconfigure:' in the SERVER INTERNET CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

ipReassembly 1.3.6.1.4.1.33.10.1.4
A control for reassembly of IP fragments. Corresponds directly to SERVER INTERNET REASSEMBLY and the value labeled 'Reassembly:' in the SERVER INTERNET CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

ipFragmentsQueuedHigh 1.3.6.1.4.1.33.10.1.5
Highest number of IP fragments queued.
OBJECT-TYPE    
  Gauge  

ipFragmentsQueuedCurrent 1.3.6.1.4.1.33.10.1.6
Current number of IP fragments queued.
OBJECT-TYPE    
  Gauge  

ipGenAdExtTable 1.3.6.1.4.1.33.10.1.7
Table of additional fields indexed by local IP address. An entry in this table is created or deleted when an entry in the MIB-II ipAddrTable is created or deleted. Although MIB-II specifies the ipAddrTable as read-only, iTouch implementations typically implement it as read-write to support modification of local IP addresses, network masks, and such.
OBJECT-TYPE    
  SEQUENCE OF  
    IpGenAdExtEntry

ipARPTimeout 1.3.6.1.4.1.33.10.1.8
A control to set the length of time in minutes before an unused ARP entry is purged from the ARP table. The default is 60 minutes. Corresponds directly to the value labeled 'Translation Table TTL' in the SERVER INTERNET CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER 1..255  

ipGatewayPingInterval 1.3.6.1.4.1.33.10.1.9
A control to set the interval of time in seconds between successive pings to the primary gateway so as to determine its status. The default is 60 seconds. Corresponds directly to the value labeled 'Gateway Timeout' in the SERVER INTERNET CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER 1..300  

ipConfigureBootp 1.3.6.1.4.1.33.10.1.11
Control to use the BOOTP protocol upon startup to learn the unit's own internet address, subnet mask, primary and secondary gateway servers, domain name servers, time server and domain name.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

ipGenAdExtEntry 1.3.6.1.4.1.33.10.1.7.1
A particular entry.
OBJECT-TYPE    
  IpGenAdExtEntry  

ipGenAdEntExtType 1.3.6.1.4.1.33.10.1.7.1.1
The way this local IP address is used, which may imply alternate, more intuitive ways to set it. primary general purpose for ordinary use rotary identificaton for rotary selection slip use for SLIP connection ppp use for PPP connection
OBJECT-TYPE    
  INTEGER primary(1), rotary(2), slip(3), ppp(4)  

ipGenAdEntExtBroadcast 1.3.6.1.4.1.33.10.1.7.1.2
Outgoing IP broadcast address associated with this local address. Value may be confined to logical compatibility with associated network mask.
OBJECT-TYPE    
  IpAddress  

tcpPortTable 1.3.6.1.4.1.33.10.2.1
A list of TCP character port entries.
OBJECT-TYPE    
  SEQUENCE OF  
    TcpPortEntry

tcpPortEntry 1.3.6.1.4.1.33.10.2.1.1
TCP parameter values for a character port.
OBJECT-TYPE    
  TcpPortEntry  

tcpPortIndex 1.3.6.1.4.1.33.10.2.1.1.1
An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the Proposed Standard Internet Character MIB.
OBJECT-TYPE    
  INTEGER  

tcpPortConnectByAddress 1.3.6.1.4.1.33.10.2.1.1.2
A control for requesting outgoing connection by internet address. 'disabled' indicates outgoing connections must be by Domain name. 'enabled' indicates that outgoing connections may be requested by internet address. Corresponds directly to PORT INTERNET CONNECTIONS and the presence of the label 'Internet Connections' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

tcpPortWindowSize 1.3.6.1.4.1.33.10.2.1.1.3
Size of the TCP window for TCP connections on the port. Corresponds directly to PORT INTERNET TCP WINDOW SIZE and the value labeled 'TCP Window Size:' in the PORT ALTERNATE CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER 64..8192  

tcpPortKeepAliveLimit 1.3.6.1.4.1.33.10.2.1.1.4
Number of minutes to maintain a TCP connection without response to keep-alive communication. A value of zero indicates no limit.
OBJECT-TYPE    
  INTEGER 0..30  

tcpResequencing 1.3.6.1.4.1.33.10.2.2
A control for keeping TCP messages received out-of-order to resequence them before using them. Corresponds directly to SERVER INTERNET TCP RESEQUENCING and the value labeled 'Resequencing:' in the SERVER INTERNET CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

tcpQueuedSegs 1.3.6.1.4.1.33.10.2.3
Number of TCP segments in the TCP receive queues. Corresponds directly to the value labeled 'TCP Packets Queued:' in the SERVER INTERNET COUNTERS display.
OBJECT-TYPE    
  Gauge  

tcpDiscardSegs 1.3.6.1.4.1.33.10.2.4
Number of TCP segments discarded due to exceeding the TCP receive queue limit. Corresponds directly to the value labeled 'TCP Packets Discarded:' in the SERVER INTERNET COUNTERS display.
OBJECT-TYPE    
  Counter  

tcpConnectTimer 1.3.6.1.4.1.33.10.2.5
Number of seconds to attempt a TCP connection without a response from the other side. The default value is 32 seconds. Corresponds directly to the SERVER INTERNET TCP CONNECT TIMER and the value labeled 'TCP Connect Timer' in the SERVER INTERNET CHARACTERISTICS display
OBJECT-TYPE    
  INTEGER 4..32  

tcpLocalPortBase 1.3.6.1.4.1.33.10.2.6
The value for port 0's tcp source port number.
OBJECT-TYPE    
  INTEGER 1..32767  

tcpLocalPortIncrement 1.3.6.1.4.1.33.10.2.7
The value by which the tcp source port number increases for each port greater than port 0.
OBJECT-TYPE    
  INTEGER 1..1024  

tcpRoutingTblSz 1.3.6.1.4.1.33.10.2.8
A control to set the size of the working routing table. The default is the current size of the table (64).
OBJECT-TYPE    
  INTEGER 64..512  

tcpDataSendDelay 1.3.6.1.4.1.33.10.2.9
A control to delay for the specified number of 10 millisecond ticks before sending the userdata string over the telnet connection.
OBJECT-TYPE    
  INTEGER 0..3000  

tcpAckDelay 1.3.6.1.4.1.33.10.2.10
A Control to prevent sending a TCP ACK when we we change TCP window size.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

tcpRetransmitMin 1.3.6.1.4.1.33.10.2.11
Number of milliseconds for the initial TCP Retransmit timer. This is the time at which a TCP session will initially retransmit unacknowledged packets.
OBJECT-TYPE    
  INTEGER 600..3000  

snmpAgentGetCommunity 1.3.6.1.4.1.33.10.3.1
The SNMP community name allowed to perform get-requests or get-next requests to this agent. Use of this value is case-insensitive. If the size is 0, the agent does not check the community name for these operations. Corresponds directly to SERVER INTERNET SNMP GET COMMUNITY and the value labeled 'Get Community:' in the SERVER INTERNET SNMP CHARACTERISTICS display.
OBJECT-TYPE    
  DisplayString Size(0..32)  

snmpAgentSetCommunity 1.3.6.1.4.1.33.10.3.2
The SNMP community name allowed to perform set-requests to this agent. Use of this value is case-insensitive. If the size is 0, the agent does not check the community name for these operations. Corresponds directly to SERVER INTERNET SNMP SET COMMUNITY and the value labeled 'Set Community:' in the SERVER INTERNET SNMP CHARACTERISTICS display.
OBJECT-TYPE    
  DisplayString Size(0..32)  

snmpAgentTrapCommunity 1.3.6.1.4.1.33.10.3.3
The SNMP community name sent in traps from this agent. Use of this value preserves case. Corresponds directly to SERVER INTERNET SNMP TRAP COMMUNITY and the value labeled 'Trap Community:' in the SERVER INTERNET SNMP CHARACTERISTICS display.
OBJECT-TYPE    
  DisplayString Size(0..32)  

snmpAgentGetClientNumber 1.3.6.1.4.1.33.10.3.4
The number of client source addresses allowed to perform get-requests or get-next requests to this agent. If the value is 0, the agent does not check source address for these operations. Corresponds indirectly to the values labeled 'Get Client n:' in the SERVER INTERNET SNMP CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER  

snmpAgentSetClientNumber 1.3.6.1.4.1.33.10.3.5
The number of client source addresses allowed to perform set-requests to this agent. If the value is 0, the agent does not check source address for these operations. Corresponds indirectly to the values labeled 'Set Client n:' in the SERVER INTERNET SNMP CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER  

snmpAgentTrapClientNumber 1.3.6.1.4.1.33.10.3.6
The number of client source addresses to which this agent sends traps. If the value is 0, the agent does not perform this operation. Corresponds indirectly to the values labeled 'Trap Client n:' in the SERVER INTERNET SNMP CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER  

getClientTable 1.3.6.1.4.1.33.10.3.7
A list of get client entries. The number of entries is given by the value of snmpAgentGetClientNumber.
OBJECT-TYPE    
  SEQUENCE OF  
    GetClientEntry

getClientEntry 1.3.6.1.4.1.33.10.3.7.1
Parameter values for a get client.
OBJECT-TYPE    
  GetClientEntry  

getClientIndex 1.3.6.1.4.1.33.10.3.7.1.1
Identification of a get client entry. Corresponds directly to the number in the label 'Get Client n:' in the SERVER INTERNET SNMP CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER  

getClientEntryStatus 1.3.6.1.4.1.33.10.3.7.1.2
Status of this entry. Setting the value to 'invalid' invalidates the entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table.
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

getClientAddressType 1.3.6.1.4.1.33.10.3.7.1.3
The type of network address contained in getClientAddress. 'unknown' means no address has been defined. 'other' means no other type value applies. 'ip' is an Internet IP address. 'ethernet' is an 802.3 MAC address. If getClientAddressType does not accompany getClientAddress in a set request, the default type is 'ip'. Corresponds indirectly to the address value labeled 'Get Client n:' in the SERVER INTERNET SNMP CHARACTERISTICS display.
OBJECT-TYPE    
  AddressType  

getClientAddress 1.3.6.1.4.1.33.10.3.7.1.4
The client's network address. If getClientAddressType does not accompany getClientAddress in a set request, the default type is 'ip'. Corresponds directly to the address value labeled 'Get Client n:' in the SERVER INTERNET SNMP CHARACTERISTICS display.
OBJECT-TYPE    
  OCTET STRING  

setClientTable 1.3.6.1.4.1.33.10.3.8
A list of set client entries. The number of entries is given by the value of snmpAgentSetClientNumber.
OBJECT-TYPE    
  SEQUENCE OF  
    SetClientEntry

setClientEntry 1.3.6.1.4.1.33.10.3.8.1
Parameter values for a set client.
OBJECT-TYPE    
  SetClientEntry  

setClientIndex 1.3.6.1.4.1.33.10.3.8.1.1
Identification of a set client entry. Corresponds directly to the number in the label 'Set Client n:' in the SERVER INTERNET SNMP CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER  

setClientEntryStatus 1.3.6.1.4.1.33.10.3.8.1.2
Status of this entry. Setting the value to 'invalid' invalidates the entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table.
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

setClientAddressType 1.3.6.1.4.1.33.10.3.8.1.3
The type of network address contained in setClientAddress. 'unknown' means no address has been defined. 'other' means no other type value applies. 'ip' is an Internet IP address. 'ethernet' is an 802.3 MAC address. If setClientAddressType does not accompany setClientAddress in a set request, the default type is 'ip'. Corresponds indirectly to the address value labeled 'Set Client n:' in the SERVER INTERNET SNMP CHARACTERISTICS display.
OBJECT-TYPE    
  AddressType  

setClientAddress 1.3.6.1.4.1.33.10.3.8.1.4
The client's network address. When setting this value, the requester must supply setClientAddressType. If setClientAddressType does not accompany setClientAddress in a set request, the default type is 'ip'. Corresponds directly to the address value labeled 'Set Client n:' in the SERVER INTERNET SNMP CHARACTERISTICS display.
OBJECT-TYPE    
  OCTET STRING  

trapClientTable 1.3.6.1.4.1.33.10.3.9
A list of trap client entries. The number of entries is given by the value of snmpAgentTrapClientNumber.
OBJECT-TYPE    
  SEQUENCE OF  
    TrapClientEntry

trapClientEntry 1.3.6.1.4.1.33.10.3.9.1
Parameter values for a trap client.
OBJECT-TYPE    
  TrapClientEntry  

trapClientIndex 1.3.6.1.4.1.33.10.3.9.1.1
Identification of a trap client entry. Corresponds directly to the number in the label 'Trap Client n:' in the SERVER INTERNET SNMP CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER  

trapClientEntryStatus 1.3.6.1.4.1.33.10.3.9.1.2
Status of this entry. Setting the value to 'invalid' invalidates the entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table.
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

trapClientAddressType 1.3.6.1.4.1.33.10.3.9.1.3
The type of network address contained in trapClientAddress. 'unknown' means no address has been defined. 'other' means no other type value applies. 'ip' is an Internet IP address. 'ethernet' is an 802.3 MAC address. If trapClientAddressType does not accompany trapClientAddress in a set request, the default type is 'ip'. Corresponds indirectly to the address value labeled 'Trap Client n:' in the SERVER INTERNET SNMP CHARACTERISTICS display.
OBJECT-TYPE    
  AddressType  

trapClientAddress 1.3.6.1.4.1.33.10.3.9.1.4
The client's network address. When setting this value, the requester must supply trapClientAddressType. If trapClientAddressType does not accompany trapClientAddress in a set request, the default type is 'ip'. Corresponds directly to the address value labeled 'Trap Client n:' in the SERVER INTERNET SNMP CHARACTERISTICS display.
OBJECT-TYPE    
  OCTET STRING  

snmpAgentAuthFailureAddress 1.3.6.1.4.1.33.10.3.10
The address of the client to most recently fail SNMP authorization.
OBJECT-TYPE    
  TypedAddress  

snmpAgentCommunityAuthenticationAlways 1.3.6.1.4.1.33.10.3.14
When enabled, indicates that community string authentication is done always for Gets, Sets, and GetNexts. When disabled, community string authentication is done once; but bypassed on subsequent Gets, Sets or GetNexts from the same address.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

domainResolverSuffix 1.3.6.1.4.1.33.10.4.1
A partial domain name for the server to append to the end of an incomplete domain name provided by the user. Corresponds directly to SERVER INTERNET DEFAULT DOMAIN SUFFIX and the value labeled 'Domain Suffix:' in the SERVER INTERNET CHARACTERISTICS display.
OBJECT-TYPE    
  DisplayString Size(0..115)  

domainResolverAddress1 1.3.6.1.4.1.33.10.4.2
The internet address of a Domain Name Server. The system can use one or two such addresses, without preference. A value of 0.0.0.0 indicates no address. Corresponds directly to SERVER INTERNET PRIMARY DOMAIN ADDRESS and the value labeled 'Primary Domain Address:' in the SERVER INTERNET CHARACTERISTICS display.
OBJECT-TYPE    
  IpAddress  

domainResolverAddress2 1.3.6.1.4.1.33.10.4.3
The internet address of a Domain Name Server. The system can use one or two such addresses, without preference. A value of 0.0.0.0 indicates no address. Corresponds directly to SERVER INTERNET SECONDARY DOMAIN ADDRESS and the value labeled 'Secondary Domain Address:' in the SERVER INTERNET CHARACTERISTICS display.
OBJECT-TYPE    
  IpAddress  

domainResolverTtl 1.3.6.1.4.1.33.10.4.4
The number of hours to keep received Domain information. Corresponds directly to SERVER INTERNET DOMAIN TTL and the value labeled ' Domain TTL:' in the SERVER INTERNET CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER 0..168  

domainResolverNameNumber 1.3.6.1.4.1.33.10.4.5
The number of Domain name mappings in this system's name cache.
OBJECT-TYPE    
  INTEGER  

nameTable 1.3.6.1.4.1.33.10.4.6
A list of Domain name entries. The number of entries is given by the value of domainResolverNameNumber.
OBJECT-TYPE    
  SEQUENCE OF  
    NameEntry

nameEntry 1.3.6.1.4.1.33.10.4.6.1
Parameter values for a Domain name.
OBJECT-TYPE    
  NameEntry  

nameName 1.3.6.1.4.1.33.10.4.6.1.1
A fully qualified domain name. Corresponds directly to the value labeled 'Domain Name' in the DOMAIN display.
OBJECT-TYPE    
  DisplayString Size(1..50)  

nameAddress 1.3.6.1.4.1.33.10.4.6.1.2
An Internet address corresponding to the Domain name. Corresponds directly to the value labeled 'Internet Address' in the DOMAIN display.
OBJECT-TYPE    
  IpAddress  

nameStatus 1.3.6.1.4.1.33.10.4.6.1.3
The status of the entry. Set to 'invalid' to remove the entry, which corresponds directly to the PURGE DOMAIN command. Actual removal of the entry is implementation specific.
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

nameSource 1.3.6.1.4.1.33.10.4.6.1.4
Source of this entry. The value meanings are: local defined by manager (LOCAL) primary obtained from a primary name server secondary obtained from a secondary name server rwho obtained from rwho Corresponds directly to the value labeled 'Source' in the DOMAIN display.
OBJECT-TYPE    
  INTEGER manager(1), primary(2), secondary(3), rwho(4)  

nameTtl 1.3.6.1.4.1.33.10.4.6.1.5
The number of minutes remaining in the entry's time to live. Corresponds directly to the value labeled 'TTL' in the DOMAIN display.
OBJECT-TYPE    
  INTEGER  

domainResolverPpp 1.3.6.1.4.1.33.10.4.7
OBJECT IDENTIFIER    

domainResolverPppPrimaryServer 1.3.6.1.4.1.33.10.4.7.1
The internet address of the primary Domain Name Server to use in PPP IPCP negotiations. A value of 0.0.0.0 indicates no address. Corresponds directly to the value labeled 'Primary WINS Address:' in the SERVER INTERNET CHARACTERISTICS display.
OBJECT-TYPE    
  IpAddress  

domainResolverPppSecondaryServer 1.3.6.1.4.1.33.10.4.7.2
The internet address of the secondary Domain Name Server to use in PPP IPCP negotiations. A value of 0.0.0.0 indicates no address. Corresponds directly to the value labeled 'Secondary WINS Address:' in the SERVER INTERNET CHARACTERISTICS display.
OBJECT-TYPE    
  IpAddress  

slipTable 1.3.6.1.4.1.33.10.5.1
A list of SLIP character port entries.
OBJECT-TYPE    
  SEQUENCE OF  
    SlipEntry

slipEntry 1.3.6.1.4.1.33.10.5.1.1
Parameter values for a SLIP port.
OBJECT-TYPE    
  SlipEntry  

slipIndex 1.3.6.1.4.1.33.10.5.1.1.1
An index value that uniquely identifies a port that can run SLIP. The port identified by a particular value of this index is the same port as identified by charPortIndex in the Proposed Standard Internet Character MIB.
OBJECT-TYPE    
  INTEGER  

slipState 1.3.6.1.4.1.33.10.5.1.1.2
A control indicating whether SLIP is in operation on the port. Corresponds directly to PORT INTERNET SLIP and the value labeled 'SLIP' in the PORT CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER off(1), on(2), compressed(3)  

slipLocalAddress 1.3.6.1.4.1.33.10.5.1.1.3
The IP address assigned to the port. Corresponds directly to PORT SLIP ADDRESS and the value labeled 'SLIP Address:' in the PORT ALTERNATE CHARACTERISTICS display.
OBJECT-TYPE    
  IpAddress  

slipRemoteAddress 1.3.6.1.4.1.33.10.5.1.1.4
The IP address of the remote system attached to the port. Corresponds directly to PORT SLIP REMOTE and the value labeled 'Remote SLIP Address:' in the PORT ALTERNATE CHARACTERISTICS display.
OBJECT-TYPE    
  IpAddress  

slipMask 1.3.6.1.4.1.33.10.5.1.1.5
The subnet mask to use for SLIP operation on the port. Corresponds directly to PORT SLIP MASK and the value labeled 'SLIP Mask:' in the PORT ALTERNATE CHARACTERISTICS display.
OBJECT-TYPE    
  IpAddress  

slipPortPacketsReceived 1.3.6.1.4.1.33.10.5.1.1.6
The number of SLIP packets received from the port. Corresponds directly to the value labeled 'Serial Packets Received:' in the PORT COUNTERS display.
OBJECT-TYPE    
  Counter  

slipPortPacketsSent 1.3.6.1.4.1.33.10.5.1.1.7
The number of SLIP packets sent to the port. Corresponds directly to the value labeled 'Serial Packets Sent:' in the PORT COUNTERS display.
OBJECT-TYPE    
  Counter  

slipPortPacketsDiscarded 1.3.6.1.4.1.33.10.5.1.1.8
The number of SLIP packets received from the port and discarded. Corresponds directly to the value labeled 'Serial Packets Discarded:' in the PORT COUNTERS display.
OBJECT-TYPE    
  Counter  

slipPortPacketLengthErrors 1.3.6.1.4.1.33.10.5.1.1.9
The number of SLIP packets received from the port with an incorrect number of bytes. Corresponds directly to the value labeled 'Serial Packet Length Errors:' in the PORT COUNTERS display.
OBJECT-TYPE    
  Counter  

slipPortPacketChecksumErrors 1.3.6.1.4.1.33.10.5.1.1.10
The number of SLIP packets received from the port with an invalid checksum. Corresponds directly to the value labeled 'Serial Packet Checksum Errors:' in the PORT COUNTERS display.
OBJECT-TYPE    
  Counter  

slipNetworkPacketsReceived 1.3.6.1.4.1.33.10.5.1.1.11
The number of SLIP packets received from the network for this port. Corresponds directly to the value labeled 'Network Packets Received:' in the PORT COUNTERS display.
OBJECT-TYPE    
  Counter  

slipNetworkPacketsSent 1.3.6.1.4.1.33.10.5.1.1.12
The number of SLIP packets sent to the network from this port. Corresponds directly to the value labeled 'Network Packets Sent:' in the PORT COUNTERS display.
OBJECT-TYPE    
  Counter  

slipNetworkPacketsDiscarded 1.3.6.1.4.1.33.10.5.1.1.13
The number of SLIP packets received from the network for this port and discarded. Corresponds directly to the value labeled 'Network Packets Discarded:' in the PORT COUNTERS display.
OBJECT-TYPE    
  Counter  

telnetPortTable 1.3.6.1.4.1.33.10.6.1
A list of Telnet character port entries.
OBJECT-TYPE    
  SEQUENCE OF  
    TelnetPortEntry

telnetPortEntry 1.3.6.1.4.1.33.10.6.1.1
Telnet parameter values for a character port.
OBJECT-TYPE    
  TelnetPortEntry  

telnetPortIndex 1.3.6.1.4.1.33.10.6.1.1.1
An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the Proposed Standard Internet Character MIB.
OBJECT-TYPE    
  INTEGER  

telnetPortIncomingTcpPort 1.3.6.1.4.1.33.10.6.1.1.2
The TCP port number offered for incoming connections to this character port. Corresponds directly to PORT TELNET REMOTE PORT and the value labeled 'Remote Port:' in the PORT TELNET CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER 1..32767  

telnetPortOutgoingTcpPort 1.3.6.1.4.1.33.10.6.1.1.3
The TCP port number used by default for outgoing connections from this character port. Corresponds directly to PORT TELNET DEFAULT PORT and the value labeled 'Default Port:' in the PORT TELNET CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER  

telnetPortNewlineTranslation 1.3.6.1.4.1.33.10.6.1.1.4
Translation to apply to newline sequences (CR/NULL or CR/LF) received from the network, before sending the newline to the character port. The value indicates the sequence sent to the character port, with 'none' meaning no translation. The lfToCrLf value converts the newline character LF received from the network to a CR/LF. Corresponds directly to PORT TELNET NEWLINE FILTERING and the value labeled 'Newline Filtering:' in the PORT TELNET CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER none(1), cr(2), crNull(3), crLf(4), std(5), lfToCrLf(6)  

telnetPortTerminalType 1.3.6.1.4.1.33.10.6.1.1.5
The terminal type character string for Telnet negotiations. Corresponds directly to PORT TELNET TERMINALTYPE and the value labeled 'TerminalType:' in the PORT TELNET CHARACTERISTICS display.
OBJECT-TYPE    
  DisplayString Size(0..21)  

telnetPortEorReflection 1.3.6.1.4.1.33.10.6.1.1.6
Control for end-of-record handshake. Corresponds directly to PORT TELNET EOR REFLECTION and the value labeled 'EOR Reflection:' in the PORT TELNET CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

telnetPortBinaryMode 1.3.6.1.4.1.33.10.6.1.1.7
Control for operation of Telnet binary mode. The value meanings are: disabled refuse binary mode negotiation (INTERACTIVE) flowControl pass all but XON and XOFF (PASTHRU) complete pass all characters (PASSALL) Corresponds directly to PORT TELNET BINARY SESSION MODE and the value labeled 'Binary Session Mode:' in the PORT TELNET CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER flowControl(1), complete(2), disabled(3)  

telnetPortSendLocation 1.3.6.1.4.1.33.10.6.1.1.8
A control indicating whether a Telnet session will initiate negotiation of the Send Location option. Corresponds directly to the PORT TELNET LOCATION and the value labeled 'Location' in the PORT TELNET CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

telnetPortClientLocation 1.3.6.1.4.1.33.10.6.1.1.9
The location of the Telnet client port. Corresponds directly to the value labeled 'Telnet Client Location' in the SESSION display.
OBJECT-TYPE    
  DisplayString Size(0..50)  

telnetPortPassiveSendLocation 1.3.6.1.4.1.33.10.6.1.1.10
A control indicating whether a Telnet session will passively respond to negotiation of the Send Location option. When disabled and telnetPortSendLocation is disabled, we will refuse to negotiate this option. When telnetPortSendLocation is enabled, it takes precedence. Corresponds directly to the value labeled 'Passive Location' in the PORT TELNET CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

telnetSerialPortTable 1.3.6.1.4.1.33.10.6.2
A list of Telnet character port entries.
OBJECT-TYPE    
  SEQUENCE OF  
    TelnetSerialPortEntry

telnetSerialPortEntry 1.3.6.1.4.1.33.10.6.2.1
Telnet parameter values for a character port.
OBJECT-TYPE    
  TelnetSerialPortEntry  

telnetSerialPortIndex 1.3.6.1.4.1.33.10.6.2.1.1
An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the Proposed Standard Internet Character MIB.
OBJECT-TYPE    
  INTEGER  

telnetSerialPortOptionDisplay 1.3.6.1.4.1.33.10.6.2.1.2
Control for display of Telnet option negotiations. Corresponds directly to PORT TELNET OPTION DISPLAY and the value labeled 'Option Display:' in the PORT TELNET CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

telnetSerialPortCsiEscape 1.3.6.1.4.1.33.10.6.2.1.3
Control for translation of 8-bit escape sequences received from the character port to 7-bit equivalents before transmission to the remote partner. Corresponds directly to PORT TELNET CSI ESCAPE and the value labeled 'CSI Escape:' in the PORT TELNET CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

telnetSerialPortEchoMode 1.3.6.1.4.1.33.10.6.2.1.4
Control for who echoes characters that come from the character port. The value meanings are: local terminal server echoes locally remote remote system echoes disabled don't default to local echo passive don't initiate negotiating of echo character initiate remote echo and suppress go ahead line reject remote echo and reject suppress go ahead noecho will not initiate echo, but will negotiate it Corresponds directly to PORT TELNET ECHO MODE and the value labeled 'Echo Mode:' in the PORT TELNET CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER local(1), remote(2), disabled(3), passive(4), character(5), line(6), noecho(7)  

telnetSerialPortNewlineMode 1.3.6.1.4.1.33.10.6.2.1.5
Translation to apply to newline (carriage return) received from the character port, before sending the newline to the remote partner. The correspondence to command keywords is 'crNull' to NULL, 'crLF' to LINEFEED, and 'verbatim' to NOTHING (that is, no translation). Corresponds directly to PORT TELNET NEWLINE and the value labeled 'Newline:' in the PORT TELNET CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER crNull(1), crLf(2), verbatim(3)  

telnetSerialPortTransmitMode 1.3.6.1.4.1.33.10.6.2.1.6
Criterion for deciding to send to the remote partner characters received from the character port. Corresponds directly to PORT TELNET TRANSMIT and the value labeled 'Transmit:' in the PORT TELNET CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER immediate(1), buffered(2), timed(3), controlchar(4)  

telnetSerialPortTransmitCharacterTimes 1.3.6.1.4.1.33.10.6.2.1.7
Number of character times to wait before transmitting when telnetSerialPortTransmitMode value is 'timed'. Corresponds directly to PORT TELNET TRANSMIT IDLETIME and the value labeled 'Transmit: Idle Time -' in the PORT TELNET CHARACTERISTICS display. This object may only be set to values 1..255. A value of 0 may be read if telnetSerialPortTransmitMode has a value of immediate or buffered
OBJECT-TYPE    
  INTEGER 0..255  

telnetSerialPortAbortOutputCharacter 1.3.6.1.4.1.33.10.6.2.1.8
Character input from the character port to cause aborting output. The value 0 indicates no character has this effect. Corresponds directly to PORT TELNET ABORT OUTPUT and the value labeled 'Abort Output Character:' in the PORT TELNET CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER 0..255  

telnetSerialPortAttentionCharacter 1.3.6.1.4.1.33.10.6.2.1.9
Character input from the character port to cause an attention notification to the remote partner. The value 0 indicates no character has this effect. Corresponds directly to PORT TELNET ATTENTION and the value labeled 'Attention Character:' in the PORT TELNET CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER 0..255  

telnetSerialPortEraseKeyCharacter 1.3.6.1.4.1.33.10.6.2.1.10
Character input from the character port to cause erasure of the previous input character. The value 0 indicates no character has this effect. Corresponds directly to PORT TELNET ERASE CHARACTER and the value labeled 'Erase Keystroke Character:' in the PORT TELNET CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER 0..255  

telnetSerialPortEraseLineCharacter 1.3.6.1.4.1.33.10.6.2.1.11
Character input from the character port to cause erasure of the previous line of input. The value 0 indicates no character has this effect. Corresponds directly to PORT TELNET ERASE LINE and the value labeled 'Erase Line Character:' in the PORT TELNET CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER 0..255  

telnetSerialPortInterruptCharacter 1.3.6.1.4.1.33.10.6.2.1.12
Character input from the character port to cause sending an interrupt notification to the remote partner. The value 0 indicates no character has this effect. Corresponds directly to PORT TELNET INTERRUPT and the value labeled 'Interrupt Character:' in the PORT TELNET CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER 0..255  

telnetSerialPortQueryCharacter 1.3.6.1.4.1.33.10.6.2.1.13
Character input from the character port to cause sending a status query to the remote partner. The value 0 indicates no character has this effect. Corresponds directly to PORT TELNET QUERY and the value labeled 'Query Character:' in the PORT TELNET CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER 0..255  

telnetSerialPortSynchronizeCharacter 1.3.6.1.4.1.33.10.6.2.1.14
Character input from the character port to cause sending a synchronization attempt to the remote partner. The value 0 indicates no character has this effect. Corresponds directly to PORT TELNET SYNCHRONIZE and the value labeled 'Synchronize Character:' in the PORT TELNET CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER 0..255  

telnetSerialPortUrgentBreak 1.3.6.1.4.1.33.10.6.2.1.15
Control for encoding breaks as Telnet urgent data. Corresponds directly to PORT TELNET URGENT BREAK and the value labeled 'Urgent Break:' in the PORT TELNET CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

telnetSerialPortRs491 1.3.6.1.4.1.33.10.6.2.1.16
A control to enable RS491 protocol processing on a port.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

telnetSerialPortTransmitBufferedTime 1.3.6.1.4.1.33.10.6.2.1.17
Number of milliseconds to wait before transmitting when telnetSerialPortTransmitMode value is 'timed'. Corresponds directly to PORT TELNET TRANSMIT BUFFERED and the value labeled 'Transmit: Buff Time -' in the PORT TELNET CHARACTERISTICS display. This object may only be set to values 30..1500. A value of 0 may be read if telnetSerialPortTransmitMode has a value of immediate, idletime or controlchar
OBJECT-TYPE    
  INTEGER 30..1500  

telnetSerialPortInterpretInterruptAsBreak 1.3.6.1.4.1.33.10.6.2.1.18
Control to interpret a Telnet Interrupt Character coming from the network as a Telnet Break Character, and to send a break out the serial port. This control is necessary for those devices which can send Telnet Interrupt but not Telnet Break. Corresponds directly to the presence of 'Telnet Interrupts Interpreted as Break' under the label 'Enabled Characteristics' in the PORT TELNET CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

telnetSerialPortPass8d 1.3.6.1.4.1.33.10.6.2.1.19
Control to pass unaltered the hexadecimal character '8D'. This control is added to ensure that this character will pass through directly in a session with 8-bit characters and parity odd or even. Corresponds directly to the presence of 'Telnet Pass 8D' under the label 'Enabled Characteristics' in the PORT TELNET CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

telnetSerialPortComControlClient 1.3.6.1.4.1.33.10.6.2.1.20
Control to begin Telnet comport control option negotiations as a client when a Telnet session is initiated. The comport control option enables a port to do outbound modem dialing on a Telnet connection. Corresponds to the value labeled 'Client:' in the PORT TELNET COMPORTCONTROL CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

telnetSerialPortComControlServer 1.3.6.1.4.1.33.10.6.2.1.21
Control to begin Telnet comport control option negotiations as a server when a Telnet session is initiated. Corresponds to the value labeled 'Server:' in the PORT TELNET COMPORTCONTROL CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

telnetSerialPortComControlServerRaisesDtr 1.3.6.1.4.1.33.10.6.2.1.22
Control for the client to request that the server raises its DTR signal on the port at the begining of the Telnet connection. Corresponds to the value labeled 'Server Raises DTR:' in the PORT TELNET COMPORTCONTROL CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

telnetSerialPortComControlClientTogglesDtr 1.3.6.1.4.1.33.10.6.2.1.23
Control to respond to the server's notification that its DCD has come high (or low) by raising (or lowering) DTR accordingly on the local port. Corresponds to the value labeled 'Client Toggles DTR:' in the PORT TELNET COMPORTCONTROL CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

tn3270DeviceNumber 1.3.6.1.4.1.33.10.7.1
The number of entries in the tn3270 Device table.
OBJECT-TYPE    
  INTEGER  

tn3270LanguageNumber 1.3.6.1.4.1.33.10.7.2
The number of entries in the tn3270 Language table.
OBJECT-TYPE    
  INTEGER  

tn3270PortKeymapStatus 1.3.6.1.4.1.33.10.7.3
Control for individual ports to create their own keymaps. Corresponds directly to SERVER TN3270 PORT KEYMAPS and the value labeled 'Port Keymaps:' in the SERVER TN3270 display.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

tn3270DeviceTable 1.3.6.1.4.1.33.10.7.4
A list of tn3270 terminal device entries.
OBJECT-TYPE    
  SEQUENCE OF  
    Tn3270DeviceEntry

tn3270DeviceEntry 1.3.6.1.4.1.33.10.7.4.1
Tn3270 parameter values for a terminal device entry.
OBJECT-TYPE    
  Tn3270DeviceEntry  

tn3270DeviceName 1.3.6.1.4.1.33.10.7.4.1.1
The name of a generic terminal device. Corresponds directly to SERVER TN3270 DEVICE and the value labeled 'Device Name:' in the SERVER TN3270 DEVICE display.
OBJECT-TYPE    
  DisplayString Size(1..8)  

tn3270DeviceStatus 1.3.6.1.4.1.33.10.7.4.1.2
Status of this entry. Setting the value to 'invalid' invalidates the entry, corresponding directly to the PURGE SERVER TN3270 DEVICE command. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. If a new device table entry is added to the table, the agent will copy the VT100 table as a default. If one plans to add a new table entry, one should not remove the VT100 entry.
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

tn3270DeviceType 1.3.6.1.4.1.33.10.7.4.1.3
The terminal type character string for use when tn3270DeviceTn3270Type is insufficient. Corresponds directly to SERVER TN3270 DEVICE TERMINALTYPE and the value labeled 'TerminalType:' in the SERVER TN3270 DEVICE display.
OBJECT-TYPE    
  DisplayString Size(0..21)  

tn3270Device3278Model 1.3.6.1.4.1.33.10.7.4.1.4
The 3278 model for the device. Corresponds directly to SERVER TN3270 DEVICE 3278Model and the value labeled '3278Model:' in the SERVER TN3270 DEVICE display.
OBJECT-TYPE    
  INTEGER model2(1), model5(2)  

tn3270DeviceKeyNumber 1.3.6.1.4.1.33.10.7.4.1.5
The number of Key table entries for this device.
OBJECT-TYPE    
  INTEGER  

tn3270DeviceScreenNumber 1.3.6.1.4.1.33.10.7.4.1.6
The number of Screen table entries for this device.
OBJECT-TYPE    
  INTEGER  

tn3270KeyTable 1.3.6.1.4.1.33.10.7.5
A list of tn3270 key entries by device.
OBJECT-TYPE    
  SEQUENCE OF  
    Tn3270KeyEntry

tn3270KeyEntry 1.3.6.1.4.1.33.10.7.5.1
Tn3270 parameter values for a key entry for a device.
OBJECT-TYPE    
  Tn3270KeyEntry  

tn3270KeyDeviceName 1.3.6.1.4.1.33.10.7.5.1.1
The name of a generic terminal device as in tn3270DeviceName. Corresponds directly to SERVER TN3270 DEVICE and the value labeled 'Device Name:' in the SERVER TN3270 DEVICE display.
OBJECT-TYPE    
  DisplayString Size(1..8)  

tn3270KeyName 1.3.6.1.4.1.33.10.7.5.1.2
The key name to which this entry applies. Corresponds directly to the key portion of SERVER TN3270 DEVICE KEYMAP and the value labeled '3270-key' in the 'Keymap:' section of the SERVER TN3270 DEVICE display.
OBJECT-TYPE    
  INTEGER newline(1), tab(2), backtab(3), cursorup(4), cursorleft(5), cursorright(6), cursordown(7), home(8), delete(9), eraseeof(10), eraseinput(11), insert(12), flushinput(13), refresh(14), centsign(15), duplicate(16), fieldmark(17), scroll(18), status(19), reset(20), fastleft(21), fastright(22), showkeys(23), print(24), pf1(39), pf2(40), pf3(41), pf4(42), pf5(43), pf6(44), pf7(45), pf8(46), pf9(47), pf10(48), pf11(49), pf12(50), pf13(51), pf14(52), pf15(53), pf16(54), pf17(55), pf18(56), pf19(57), pf20(58), pf21(59), pf22(60), pf23(61), pf24(62), pa1(63), pa2(64), pa3(65), sysreq(66), enter(67), clear(68), cursorsel(69), test(70)  

tn3270KeyStatus 1.3.6.1.4.1.33.10.7.5.1.3
Status of this entry. Setting the value to 'invalid' invalidates the entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table.
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

tn3270KeyCharacterSequence 1.3.6.1.4.1.33.10.7.5.1.4
The ASCII character sequence for the key. Corresponds directly to the escape-sequence portion of SERVER TN3270 DEVICE KEYMAP and the value labeled 'KeyCode' in the 'Keymap:' section of the SERVER TN3270 DEVICE display.
OBJECT-TYPE    
  OCTET STRING Size(0..8)  

tn3270KeyDescription 1.3.6.1.4.1.33.10.7.5.1.5
Descriptive text for the key. Corresponds directly to the description portion of SERVER TN3270 DEVICE KEYMAP and the value labeled 'Description' in the SERVER TN3270 DEVICE display.
OBJECT-TYPE    
  DisplayString Size(0..5)  

tn3270ScreenTable 1.3.6.1.4.1.33.10.7.6
A list of tn3270 screen action entries by device.
OBJECT-TYPE    
  SEQUENCE OF  
    Tn3270ScreenEntry

tn3270ScreenEntry 1.3.6.1.4.1.33.10.7.6.1
Tn3270 parameter values for a screen action entry for a device.
OBJECT-TYPE    
  Tn3270ScreenEntry  

tn3270ScreenDeviceName 1.3.6.1.4.1.33.10.7.6.1.1
The name of a generic terminal device as in tn3270DeviceName. Corresponds directly to SERVER TN3270 DEVICE and the value labeled 'Device Name:' in the SERVER TN3270 DEVICE display.
OBJECT-TYPE    
  DisplayString Size(1..8)  

tn3270ScreenActionName 1.3.6.1.4.1.33.10.7.6.1.2
The screen action to which this entry applies. Corresponds directly to the action portion of SERVER TN3270 DEVICE SCREENMAP and the value labeled 'Terminal Function' in the 'Screenmap: section of the SERVER TN3270 DEVICE display.
OBJECT-TYPE    
  INTEGER eraseeol(1), clearscr(2), movecursor(3), col132(4), col80(5), beep(6), charset(7), boldon(8), boldoff(9), blinkon(10), blinkoff(11), underscoreon(12), underscoreoff(13), reverseon(14), reverseoff(15), colorBlue(16), colorRed(17), colorPink(18), colorGreen(19), colorTurquoise(20), colorYellow(21), colorWhite(22), status1(26), status2(27), reset1(28), reset2(29), reset3(30), reset4(31), base(32), sgr(33)  

tn3270ScreenStatus 1.3.6.1.4.1.33.10.7.6.1.3
Status of this entry. Setting the value to 'invalid' invalidates the entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table.
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

tn3270ScreenCharacterSequence 1.3.6.1.4.1.33.10.7.6.1.4
The ASCII character sequence for the screen action. Some actions may have a lesser length limit. Corresponds directly to the escape-sequence portion of SERVER TN3270 DEVICE SCREENMAP and the value labeled 'HexCode' in the 'Screenmap: section of the SERVER TN3270 DEVICE display.
OBJECT-TYPE    
  OCTET STRING Size(0..15)  

tn3270LanguageTable 1.3.6.1.4.1.33.10.7.7
A list of tn3270 language entries.
OBJECT-TYPE    
  SEQUENCE OF  
    Tn3270LanguageEntry

tn3270LanguageEntry 1.3.6.1.4.1.33.10.7.7.1
Tn3270 parameter values for a language entry.
OBJECT-TYPE    
  Tn3270LanguageEntry  

tn3270LanguageName 1.3.6.1.4.1.33.10.7.7.1.1
The name of language for character translation tables. Corresponds directly to SERVER TN3270 LANGUAGE and the value labeled 'Language Name:' in the SERVER LANGUAGE display.
OBJECT-TYPE    
  DisplayString Size(1..8)  

tn3270LanguageStatus 1.3.6.1.4.1.33.10.7.7.1.2
Status of this entry. Setting the value to 'invalid' invalidates the entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. If a new device table entry is added to the table, the agent will copy the USENGLSH table as the default.
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

eToALanguageTable 1.3.6.1.4.1.33.10.7.8
A list of language EBCDIC to ASCII conversion entries.
OBJECT-TYPE    
  SEQUENCE OF  
    EToALanguageEntry

eToALanguageEntry 1.3.6.1.4.1.33.10.7.8.1
EBCDIC to ASCII parameter values for a language entry.
OBJECT-TYPE    
  EToALanguageEntry  

eToALanguageName 1.3.6.1.4.1.33.10.7.8.1.1
The name of language from the language table.
OBJECT-TYPE    
  DisplayString Size(1..8)  

eToAOffset 1.3.6.1.4.1.33.10.7.8.1.2
EBCDIC character offset plus one, that is, the value 1 corresponds to an operational offset of 0. Corresponds directly to the offset portion of SERVER TN3270 LANGUAGE and the hexadecimal labels around the conversion table labeled 'EBCDIC to ASCII' in the SERVER LANGUAGE display.
OBJECT-TYPE    
  INTEGER 65..256  

eToAValue 1.3.6.1.4.1.33.10.7.8.1.3
ASCII character value for the EBCDIC offset. Corresponds directly to the value portion of SERVER TN3270 LANGUAGE and the values in the conversion table labeled 'EBCDIC to ASCII' in the SERVER LANGUAGE display.
OBJECT-TYPE    
  INTEGER 32..255  

aToELanguageTable 1.3.6.1.4.1.33.10.7.9
A list of language ASCII to EBCDIC conversion entries.
OBJECT-TYPE    
  SEQUENCE OF  
    AToELanguageEntry

aToELanguageEntry 1.3.6.1.4.1.33.10.7.9.1
ASCII to EBCDIC parameter values for a language entry.
OBJECT-TYPE    
  AToELanguageEntry  

aToELanguageName 1.3.6.1.4.1.33.10.7.9.1.1
The name of language from the language table.
OBJECT-TYPE    
  DisplayString Size(1..8)  

aToEOffset 1.3.6.1.4.1.33.10.7.9.1.2
ASCII character offset plus one, that is, the value 1 corresponds to an operational offset of 0. Corresponds directly to the offset portion of SERVER TN3270 LANGUAGE and the hexadecimal labels around the conversion table labeled 'ASCII to EBCDIC' in the SERVER LANGUAGE display.
OBJECT-TYPE    
  INTEGER 33..256  

aToEValue 1.3.6.1.4.1.33.10.7.9.1.3
EBCDIC character value for the ASCII offset. Corresponds directly to the value portion of SERVER TN3270 LANGUAGE and the values in the conversion table labeled 'ASCII to EBCDIC' in the SERVER LANGUAGE display.
OBJECT-TYPE    
  INTEGER 0..255  

tn3270PortTable 1.3.6.1.4.1.33.10.7.10
A list of tn3270 character port entries.
OBJECT-TYPE    
  SEQUENCE OF  
    Tn3270PortEntry

tn3270PortEntry 1.3.6.1.4.1.33.10.7.10.1
Parameter values for a tn3270 port.
OBJECT-TYPE    
  Tn3270PortEntry  

tn3270PortIndex 1.3.6.1.4.1.33.10.7.10.1.1
An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the Proposed Standard Internet Character MIB.
OBJECT-TYPE    
  INTEGER  

tn3270PortDeviceName 1.3.6.1.4.1.33.10.7.10.1.2
The name of a generic terminal device from the tn3270 device table. Corresponds directly to PORT TELNET TN3270 DEVICE and the value labeled 'Tn3270 Device:' in the PORT TELNET display.
OBJECT-TYPE    
  DisplayString Size(0..8)  

tn3270PortLanguageName 1.3.6.1.4.1.33.10.7.10.1.3
The name of language from the tn3270 language table. Corresponds directly to PORT TELNET TN3270 LANGUAGE and the value labeled 'Tn3270 Language:' in the PORT TELNET display.
OBJECT-TYPE    
  DisplayString Size(0..8)  

tn3270PortExtendedAttributes 1.3.6.1.4.1.33.10.7.10.1.4
A control indicating that certain 3270 extended attributes are supported on the port. Corresponds directly to PORT TELNET TN3270 XTDATTRS and the label 'Tn3270 XtdAttrs' following the label 'Enabled Characteristics' in the PORT TELNET display.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

tn3270PortEorNegotiation 1.3.6.1.4.1.33.10.7.10.1.5
A control for negotiation of the Telnet EOR option when establishing a tn3270 session on the port. Corresponds directly to PORT TELNET TN3270 EOR and the label 'Tn3270 EOR' following the label 'Enabled Characteristics' in the PORT TELNET display.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

tn3270PortErrorLock 1.3.6.1.4.1.33.10.7.10.1.6
A control for requiring use the RESET key when the host reports an error during a tn3270 session on the port. Corresponds directly to PORT TELNET TN3270 ERRORLOCK and the label 'Tn3270 ErrorLock' following the label 'Enabled Characteristics' in the PORT TELNET display.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

tn3270PortPrinterPort 1.3.6.1.4.1.33.10.7.10.1.7
The port number of the tn3270 printer. Corresponds directly to PORT TELNET TN3270 PRINTER and the value labeled 'Tn3270 Printer:' in the PORT TELNET display.
OBJECT-TYPE    
  INTEGER  

tn3270PortOutgoingTcpPort 1.3.6.1.4.1.33.10.7.10.1.8
The TCP port which is used for a TN3270 session when connecting to a remote host from this serial port. Corresponds directly to the value labeled 'Tn3270 Default Port:' in the PORT TELNET CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER 1..32767  

tn3270PortSpaceInsert 1.3.6.1.4.1.33.10.7.10.1.9
Control to allow insert mode within a space filled field, and write characters over EBCDIC spaces. Corresponds directly to the presence of 'Tn3270 Space_Insert' under the label 'Enabled Characteristics' in the PORT TELNET CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

tn3270PortTypeAhead 1.3.6.1.4.1.33.10.7.10.1.10
Control to permit typing ahead in a tn3270 session prior to receiving a response from the host for the previous command entered. Corresponds directly to the presence of 'Tn3270 TypeAhead' under the label 'Enabled Characteristics' in the PORT TELNET CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

tn3270PrefixKeyMap 1.3.6.1.4.1.33.10.7.10.1.11
Control to prepend a prefix function to another function key. When the operator hits the key the prepended function(s) and then the main function for the key are transmitted to the host. Corresponds directly to the presence of 'Tn3270 PrefixKeyMap' under the label 'Enabled Characteristics' in the PORT TELNET CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

tn3270PortScanner 1.3.6.1.4.1.33.10.7.10.1.12
Indicates that this is a tn3270 scanner port. Corresponds directly to the presence of 'Tn3270 SCANNER' under the label 'Enabled Characteristics' in the PORT TELNET CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

kerbStatus 1.3.6.1.4.1.33.10.8.1
A control indicating the level of Kerberos operation on the system. Corresponds directly to SERVER KERBEROS STATUS and the value labeled 'Kerberos Security:' in the SERVER KERBEROS display.
OBJECT-TYPE    
  INTEGER none(1), login(2)  

kerbRealm 1.3.6.1.4.1.33.10.8.2
The Kerberos realm with which the kerbServerName1 and kerbServerName2 are associated. Corresponds directly to SERVER KERBEROS REALM and the value labeled 'Kerberos Realm:' in the SERVER KERBEROS display.
OBJECT-TYPE    
  DisplayString Size(0..40)  

kerbQueryLimit 1.3.6.1.4.1.33.10.8.3
The maximum number of attempts the system can make when trying to verify a Kerberos ID. Corresponds directly to SERVER KERBEROS QUERY LIMIT and the value labeled 'Kerberos Query Limit:' in the SERVER KERBEROS display.
OBJECT-TYPE    
  INTEGER 1..16  

kerbMasterName 1.3.6.1.4.1.33.10.8.4
The Domain name of the Kerberos master host system, which holds the Kerberos database. Corresponds directly to SERVER KERBEROS MASTER and the value labeled 'Kerberos Master:' in the SERVER KERBEROS display.
OBJECT-TYPE    
  DisplayString Size(0..50)  

kerbServerName1 1.3.6.1.4.1.33.10.8.5
The Domain name of the first Kerberos server to try when the system verifys a Kerberos ID. Corresponds directly to SERVER KERBEROS PRIMARY SERVER and the value labeled 'Kerberos Primary Server:' in the SERVER KERBEROS display.
OBJECT-TYPE    
  DisplayString Size(0..50)  

kerbServerName2 1.3.6.1.4.1.33.10.8.6
The Domain name of the Kerberos server to try when the system verifys a Kerberos ID and cannot reach the Kerberos primary server. Corresponds directly to SERVER KERBEROS SECONDARY SERVER and the value labeled 'Kerberos Secondary Server:' in the SERVER KERBEROS display.
OBJECT-TYPE    
  DisplayString Size(0..50)  

kerbInsecureLogins 1.3.6.1.4.1.33.10.8.7
The number of user logins on ports for which Kerberos user verification is not enabled. Corresponds directly to the value labeled 'Logins without Kerberos:' in the SERVER KERBEROS display.
OBJECT-TYPE    
  Counter  

kerbSecureLogins 1.3.6.1.4.1.33.10.8.8
The number of successful user logins on ports for which Kerberos user verification is enabled. Corresponds directly to the value labeled 'Successful Logins:' in the SERVER KERBEROS display.
OBJECT-TYPE    
  Counter  

kerbSecureLoginsFailed 1.3.6.1.4.1.33.10.8.9
The number of verification failures due to incorrect ID or password for attempted user logins on ports for which Kerberos user verification is enabled. Corresponds directly to the value labeled 'Unsuccessful Logins:' in the SERVER KERBEROS display.
OBJECT-TYPE    
  Counter  

kerbPasswordChangeFailed 1.3.6.1.4.1.33.10.8.10
The number of user failures to change their Kerberos password due to invalid old password or new password verification. Corresponds directly to the value labeled 'Password Change Failures:' in the SERVER KERBEROS display.
OBJECT-TYPE    
  Counter  

kerbError 1.3.6.1.4.1.33.10.8.11
The error number of the most recent Kerberos-related failure. Corresponds directly to the value labeled 'Last Kerberos Error:' in the SERVER KERBEROS display. For a list of error numbers and their meanings, consult relevant iTouch or Kerberos documentation.
OBJECT-TYPE    
  INTEGER  

kerbErrorTime 1.3.6.1.4.1.33.10.8.12
The date and time that kerbError was last updated. Corresponds directly to the value labeled 'Occurred:' in the SERVER KERBEROS display.
OBJECT-TYPE    
  DateTime  

kerbMasterAccess 1.3.6.1.4.1.33.10.8.13
The number of times the system successfully accessed the Kerberos master host. Corresponds directly to the value labeled 'Attempts to access:', 'Master', and 'Successful:' in the SERVER KERBEROS display.
OBJECT-TYPE    
  Counter  

kerbMasterAccessFailed 1.3.6.1.4.1.33.10.8.14
The number of times the system failed access to the Kerberos master host. Corresponds directly to the value labeled 'Attempts to access:', 'Master', and 'Unsuccessful:' in the SERVER KERBEROS display.
OBJECT-TYPE    
  Counter  

kerbServerAccess1 1.3.6.1.4.1.33.10.8.15
The number of times the system successfully accessed the Kerberos primary server. Corresponds directly to the value labeled 'Attempts to access:', 'Server1', and 'Successful:' in the SERVER KERBEROS display.
OBJECT-TYPE    
  Counter  

kerbServerAccessFailed1 1.3.6.1.4.1.33.10.8.16
The number of times the system failed access to the Kerberos primary server. Corresponds directly to the value labeled 'Attempts to access:', 'Server1', and 'Unsuccessful:' in the SERVER KERBEROS display.
OBJECT-TYPE    
  Counter  

kerbServerAccess2 1.3.6.1.4.1.33.10.8.17
The number of times the system successfully accessed the Kerberos secondary server. Corresponds directly to the value labeled 'Attempts to access:', 'Server2', and 'Successful:' in the SERVER KERBEROS display.
OBJECT-TYPE    
  Counter  

kerbServerAccessFailed2 1.3.6.1.4.1.33.10.8.18
The number of times the system failed access to the Kerberos secondary server. Corresponds directly to the value labeled 'Attempts to access:', 'Server2', and 'Unsuccessful:' in the SERVER KERBEROS display.
OBJECT-TYPE    
  Counter  

kerbPortTable 1.3.6.1.4.1.33.10.8.19
A list of Kerberos character port entries.
OBJECT-TYPE    
  SEQUENCE OF  
    KerbPortEntry

kerbPortEntry 1.3.6.1.4.1.33.10.8.19.1
Parameter values for a Kerberos port.
OBJECT-TYPE    
  KerbPortEntry  

kerbPortIndex 1.3.6.1.4.1.33.10.8.19.1.1
An index value that uniquely identifies a port could relate to Kerberos. The port identified by a particular value of this index is the same port as identified by charPortIndex in the Proposed Standard Internet Character MIB.
OBJECT-TYPE    
  INTEGER  

kerbPortStatus 1.3.6.1.4.1.33.10.8.19.1.2
A control indicating the level of Kerberos operation on the port. Corresponds directly to PORT KERBEROS and the value 'Kerberos' following the label 'Enabled Characteristics' in the PORT CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER none(1), login(2)  

kerbServerPort 1.3.6.1.4.1.33.10.8.20
The UDP port number on the Kerberos server where Kerberos messages are sent.
OBJECT-TYPE    
  INTEGER standardPort(88), experimentalPort(750)  

psEntryNumber 1.3.6.1.4.1.33.10.9.1
The number of security entries in this system's port security table with psEntryStatus of 'valid'.
OBJECT-TYPE    
  INTEGER  

psEntryNumberLimit 1.3.6.1.4.1.33.10.9.2
The maximum number of security entries in this system's port security table.
OBJECT-TYPE    
  INTEGER  

psEntryInvalidIndex 1.3.6.1.4.1.33.10.9.3
A value of psEntryIndex for an entry that has psEntryStatus of 'invalid'. A management station may choose this value when adding a new entry. Collisions between independent management stations simultaneously using the same number are beyond the scope of this document.
OBJECT-TYPE    
  INTEGER  

psPortTable 1.3.6.1.4.1.33.10.9.4
A list of port security character port entries.
OBJECT-TYPE    
  SEQUENCE OF  
    PsPortEntry

psPortEntry 1.3.6.1.4.1.33.10.9.4.1
Port security parameter values for a port.
OBJECT-TYPE    
  PsPortEntry  

psPortIndex 1.3.6.1.4.1.33.10.9.4.1.1
An index value that uniquely identifies a port for security purposes. The port identified by a particular value of this index is the same port as identified by charPortIndex in the Proposed Standard Internet Character MIB.
OBJECT-TYPE    
  INTEGER  

psPortDefaultInboundAccess 1.3.6.1.4.1.33.10.9.4.1.2
The default access to the port for incoming TCP connections. Corresponds directly to PORT INTERNET SECURITY DEFAULT INBOUND and the value labeled 'Inbound Default:' in the PORT INTERNET SECURITY display.
OBJECT-TYPE    
  INTEGER allow(1), deny(2)  

psPortDefaultOutboundAccess 1.3.6.1.4.1.33.10.9.4.1.3
The default access to the port for outgoing TCP connections. Corresponds directly to PORT INTERNET SECURITY DEFAULT OUTBOUND and the value labeled 'Outbound Default:' in the PORT INTERNET SECURITY display.
OBJECT-TYPE    
  INTEGER allow(1), deny(2)  

psClrInternetSecurity 1.3.6.1.4.1.33.10.9.4.1.4
A control for if the internet security entries for this port will be cleared upon port logout. The default is disabled.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

psTable 1.3.6.1.4.1.33.10.9.5
A list of port security entries.
OBJECT-TYPE    
  SEQUENCE OF  
    PsEntry

psEntry 1.3.6.1.4.1.33.10.9.5.1
Port security parameter values for an entry for a port.
OBJECT-TYPE    
  PsEntry  

psEntryIndex 1.3.6.1.4.1.33.10.9.5.1.1
A small, numeric distinguisher for port security entries. When adding a new entry, the client should specify an unused value, such as psEntryInvalidIndex. Corresponds directly to the value labeled 'Entry' in the SERVER INTERNET SECURITY display.
OBJECT-TYPE    
  INTEGER  

psEntryStatus 1.3.6.1.4.1.33.10.9.5.1.2
Status of this entry. Setting the value to 'invalid' invalidates the entry, corresponding directly to the CLEAR INTERNET SECURITY command. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Setting this object to 'valid' has no effect. When creating a new instance, one must set psEntryAddress, psEntryMask, psEntryAccess, psEntryDirection and psEntryPortList for the new instance in the same physical set request. Furthermore, if one wishes to change an entry, one must first delete it and then add it with its new values.
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

psEntryAddress 1.3.6.1.4.1.33.10.9.5.1.3
The IP address to which the entry pertains. Corresponds directly to the PORT INTERNET SECURITY internet address and the value labeled 'Internet Address' in the SERVER INTERNET SECURITY display.
OBJECT-TYPE    
  IpAddress  

psEntryMask 1.3.6.1.4.1.33.10.9.5.1.4
The mask applied to psEntryAddress when making a security check based on this entry. Corresponds directly to PORT INTERNET SECURITY MASK and the value labeled 'Security Mask' in the SERVER INTERNET SECURITY display.
OBJECT-TYPE    
  IpAddress  

psEntryAccess 1.3.6.1.4.1.33.10.9.5.1.5
The access to the port for TCP connections when making a security check based on this entry. Corresponds directly to PORT INTERNET SECURITY ALLOW or DENY and the value labeled 'Access' in the SERVER INTERNET SECURITY display.
OBJECT-TYPE    
  INTEGER allow(1), deny(2)  

psEntryDirection 1.3.6.1.4.1.33.10.9.5.1.6
The direction of TCP connections to which this entry applies. Corresponds directly to PORT INTERNET SECURITY INBOUND or OUTBOUND and the value labeled 'Direction' in the SERVER INTERNET SECURITY display.
OBJECT-TYPE    
  INTEGER inbound(1), outbound(2)  

psEntryPortMap 1.3.6.1.4.1.33.10.9.5.1.7
The list of character ports to which this entry applies. The OCTET STRING contains a bitmap, with one bit for each port, and enough octets for all the ports on the system. Port numbers are as defined for charPortIndex in the Proposed Standard Internet Character MIB. Corresponding bit numbers start with 1 as the high-order bit of the first octet. Corresponds directly to PORT INTERNET SECURITY and the value labeled 'Ports' in the SERVER INTERNET SECURITY display.
OBJECT-TYPE    
  OCTET STRING  

xremoteServerName1 1.3.6.1.4.1.33.10.10.1
The Domain name of the first XREMOTE font server to try for downloading fonts. Corresponds directly to SERVER XREMOTE PRIMARY SERVER and the value labeled 'Xremote Primary Font Server:' in the SERVER XREMOTE display.
OBJECT-TYPE    
  DisplayString Size(0..50)  

xremoteServerName2 1.3.6.1.4.1.33.10.10.2
The Domain name of the XREMOTE font server to try for downloading fonts and the primary font server does not respond. Corresponds directly to SERVER XREMOTE SECONDARY SERVER and the value labeled 'Xremote Secondary Font Server:' in the SERVER XREMOTE display.
OBJECT-TYPE    
  DisplayString Size(0..50)  

xremoteServerAccess1 1.3.6.1.4.1.33.10.10.3
The number of times the system successfully accessed the XREMOTE primary font server. Corresponds directly to the value labeled 'Attempts to access:', 'Server1', and 'Successful:' in the SERVER XREMOTE display.
OBJECT-TYPE    
  Counter  

xremoteServerAccessFailed1 1.3.6.1.4.1.33.10.10.4
The number of times the system failed access to the XREMOTE primary font server. Corresponds directly to the value labeled 'Attempts to access:', 'Server1', and 'Unsuccessful:' in the SERVER XREMOTE display.
OBJECT-TYPE    
  Counter  

xremoteServerAccess2 1.3.6.1.4.1.33.10.10.5
The number of times the system successfully accessed the XREMOTE secondary font server. Corresponds directly to the value labeled 'Attempts to access:', 'Server2', and 'Successful:' in the SERVER XREMOTE display.
OBJECT-TYPE    
  Counter  

xremoteServerAccessFailed2 1.3.6.1.4.1.33.10.10.6
The number of times the system failed access to the XREMOTE secondary font server. Corresponds directly to the value labeled 'Attempts to access:', 'Server2', and 'Unsuccessful:' in the SERVER XREMOTE display.
OBJECT-TYPE    
  Counter  

xremoteSessions 1.3.6.1.4.1.33.10.10.7
The number of connected XREMOTE sessions. Corresponds directly to the value labeled 'Current Number of Xremote Sessions:' in the SERVER XREMOTE display.
OBJECT-TYPE    
  Gauge  

xremotePortTable 1.3.6.1.4.1.33.10.10.8
A list of XREMOTE character port entries.
OBJECT-TYPE    
  SEQUENCE OF  
    XremotePortEntry

xremotePortEntry 1.3.6.1.4.1.33.10.10.8.1
XREMOTE parameter values for a port.
OBJECT-TYPE    
  XremotePortEntry  

xremotePortIndex 1.3.6.1.4.1.33.10.10.8.1.1
An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the Proposed Standard Internet Character MIB.
OBJECT-TYPE    
  INTEGER  

xremotePortXremote 1.3.6.1.4.1.33.10.10.8.1.2
Control for use of XREMOTE on the port. Corresponds directly to PORT XREMOTE and the presence of the label 'Xremote' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

xremotePortXdmQuery 1.3.6.1.4.1.33.10.10.8.1.3
The type of query message issued by a port when searching for an X Display Manager (XDM). Corresponds directly to the PORT XDM QUERY and the 'XDM Query:' in the PORT ALTERNATE CHARACTERISTICS display
OBJECT-TYPE    
  INTEGER specific(1), broadcast(2), indirect(3)  

xremotePortXdmHost 1.3.6.1.4.1.33.10.10.8.1.4
The Domain name or Internet address of the X Display Manager (XDM) for a port. Corresponds directly to the PORT XDM HOST and the 'XDM Host:' in the PORT ALTERNATE CHARACTERISTICS display
OBJECT-TYPE    
  DisplayString Size(0..50)  

xremoteServerClients 1.3.6.1.4.1.33.10.10.9
The number of active X clients. Corresponds directly to the value labeled 'Current Number of XClients:' in the SERVER XREMOTE display.
OBJECT-TYPE    
  Gauge  

rotaryNumber 1.3.6.1.4.1.33.10.11.1
The number of entries in the Rotary table.
OBJECT-TYPE    
  INTEGER  

rotaryTable 1.3.6.1.4.1.33.10.11.2
A list of rotary entries.
OBJECT-TYPE    
  SEQUENCE OF  
    RotaryEntry

rotaryEntry 1.3.6.1.4.1.33.10.11.2.1
Parameter values for a rotary.
OBJECT-TYPE    
  RotaryEntry  

rotaryAddress 1.3.6.1.4.1.33.10.11.2.1.1
The internet address to be recognized as a rotary. Corresponds directly to the ip-address portion of SERVER INTERNET ROTARY and the value labeled 'Internet Address' in the SERVER INTERNET ROTARY display.
OBJECT-TYPE    
  IpAddress  

rotaryStatus 1.3.6.1.4.1.33.10.11.2.1.2
Status of this entry. Setting the value to 'invalid' invalidates the entry, corresponding directly to the CLEAR SERVER INTERNET ROTARY command. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Setting the value to 'valid' in conjunction with a new rotaryAddress will add a new entry to the table. When adding a new entry, one should also specify a rotaryPortMap as the DEFVAL of 0..0 for rotaryPortMap is meaningless.
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

rotaryPortMap 1.3.6.1.4.1.33.10.11.2.1.3
The list of character ports that compose the rotary. The OCTET STRING contains a bitmap, with one bit for each port, and enough octets for all the ports on the system. Port numbers are as defined for charPortIndex in the Proposed Standard Internet Character MIB. Corresponding bit numbers start with 1 as the high-order bit of the first octet. Corresponds directly to port-list portion of SERVER INTERNET ROTARY and the value labeled 'Ports' in the SERVER INTERNET ROTARY display.
OBJECT-TYPE    
  OCTET STRING  

egpRouting 1.3.6.1.4.1.33.10.12.1
Control for EGP routing services.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

egpStatus 1.3.6.1.4.1.33.10.12.2
Status of the EGP routing services indicating why it is not running.
OBJECT-TYPE    
  INTEGER active(1), noMemory(2), noIpRouting(3), noEgpRouting(4), noNeighbors(5), noAS(6)  

egpNbrTable 1.3.6.1.4.1.33.10.12.3
The EGP neighbor table.
OBJECT-TYPE    
  SEQUENCE OF  
    EgpNbrEntry

egpNbrEntry 1.3.6.1.4.1.33.10.12.3.1
Information about this entity's relationship with a particular EGP neighbor.
OBJECT-TYPE    
  EgpNbrEntry  

egpNbrAddr 1.3.6.1.4.1.33.10.12.3.1.1
The IP address of this entry's EGP neighbor.
OBJECT-TYPE    
  IpAddress  

egpNbrIntervalDead 1.3.6.1.4.1.33.10.12.3.1.2
The interval upon entering the cease or idle state before automatically assuming a Start Event has occured. If a neighbor does not respond within 5 minutes, a Stop Event will automatically occur. The interval is in hundredths of seconds.
OBJECT-TYPE    
  INTEGER 0..65535  

egpNbrStatus 1.3.6.1.4.1.33.10.12.3.1.3
The status of the entry for this neighbor. Set to 'invalid' to remove the entry.
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

ospfAutoConfigure 1.3.6.1.4.1.33.10.13.1
Control whether OSPF will automatically configure itself.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

ospfStatus 1.3.6.1.4.1.33.10.13.2
Status of the OSPF routing services indicating why it is not running.
OBJECT-TYPE    
  INTEGER active(1), noMemory(2), noIpRouting(3), noOspfRouting(4), noAreas(5), noInterfaces(6), noRtrId(7), noBackBoneAndVirtualInterfaces(8), noBackBoneAndInterface(9), noBackBone(10)  

ospfIfMtrcTable 1.3.6.1.4.1.33.10.13.3
The TOS metrics for a non-virtual interface identified by the interface index.
OBJECT-TYPE    
  SEQUENCE OF  
    OspfIfMtrcEntry

ospfIfMtrcEntry 1.3.6.1.4.1.33.10.13.3.1
A particular TOS metric for a non-virtual interface identified by the interface index.
OBJECT-TYPE    
  OspfIfMtrcEntry  

ospfIfMtrcIpAddress 1.3.6.1.4.1.33.10.13.3.1.1
Same as ospfIfMetricIpAddress in OSPF MIB, the IP address of this OSPF interface.
OBJECT-TYPE    
  IpAddress  

ospfIfMtrcAddressLessIf 1.3.6.1.4.1.33.10.13.3.1.2
Same as ospfIfMetricAddressLessIf in OSPF MIB, for the purpose of easing the instancing of addressed and addressless interfaces. This variable takes the value 0 on interfaces with IP Addresses, and the value of ifIndex for interfaces having no IP Address.
OBJECT-TYPE    
  INTEGER  

ospfIfMtrcTos 1.3.6.1.4.1.33.10.13.3.1.3
Same as ospfIfMetricTOS in OSPF MIB, the type of service metric being referenced.
OBJECT-TYPE    
  INTEGER 1..16  

ospfIfMtrcCostActual 1.3.6.1.4.1.33.10.13.3.1.4
The actual cost of the metric in case it was set to auto.
OBJECT-TYPE    
  INTEGER 1..65535  

ospfXIfTable 1.3.6.1.4.1.33.10.13.4
The TOS metrics for a non-virtual interface identified by the interface index.
OBJECT-TYPE    
  SEQUENCE OF  
    OspfXIfEntry

ospfXIfEntry 1.3.6.1.4.1.33.10.13.4.1
Interface parameters for OSPF.
OBJECT-TYPE    
  OspfXIfEntry  

ospfXIfIpAddress 1.3.6.1.4.1.33.10.13.4.1.1
Same as ospfIfIpAddress in OSPF MIB, the IP address of this OSPF interface.
OBJECT-TYPE    
  IpAddress  

ospfXIfAddressLessIf 1.3.6.1.4.1.33.10.13.4.1.2
Same as ospfIfAddressLessIf in OSPF MIB, for the purpose of easing the instancing of addressed and addressless interfaces. This variable takes the value 0 on interfaces with IP Addresses, and the value of ifIndex for interfaces having no IP Address.
OBJECT-TYPE    
  INTEGER  

ospfXIfTypeActual 1.3.6.1.4.1.33.10.13.4.1.3
The interface type.
OBJECT-TYPE    
  INTEGER broadcast(1), nonbroadcast(2), pointToPoint(3)  

ospfXIfStatus 1.3.6.1.4.1.33.10.13.4.1.4
The status of the interface entry, including the entry in the standard OSPF MIB. Set to 'invalid' to remove the entry.
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

ospfXAreaTable 1.3.6.1.4.1.33.10.13.5
Parameters for an OSPF area.
OBJECT-TYPE    
  SEQUENCE OF  
    OspfXAreaEntry

ospfXAreaEntry 1.3.6.1.4.1.33.10.13.5.1
An area entry.
OBJECT-TYPE    
  OspfXAreaEntry  

ospfXAreaId 1.3.6.1.4.1.33.10.13.5.1.1
Same as ospfAreaId in OSPF MIB, the ID of the area.
OBJECT-TYPE    
  IpAddress  

ospfXAreaStatus 1.3.6.1.4.1.33.10.13.5.1.2
The status of the area entry, including the entry in the standard OSPF MIB. Set to 'invalid' to remove the entry.
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

ipAdExtTable 1.3.6.1.4.1.33.10.14.1
Table of additional fields indexed by local IP address. An entry in this table is created or deleted when an entry in the ipAddrTable is created or deleted.
OBJECT-TYPE    
  SEQUENCE OF  
    IpAdExtEntry

ipAdExtEntry 1.3.6.1.4.1.33.10.14.1.1
A particular entry.
OBJECT-TYPE    
  IpAdExtEntry  

ipAdEntExtAddress 1.3.6.1.4.1.33.10.14.1.1.1
Same as ipAdEntAddr, a local address representing a network connection.
OBJECT-TYPE    
  IpAddress  

ipAdEntExtProxyArp 1.3.6.1.4.1.33.10.14.1.1.2
Controls whether proxy ARP is active for this local address.
OBJECT-TYPE    
  INTEGER enabled(2), disabled(1)  

ipAdEntExtRip 1.3.6.1.4.1.33.10.14.1.1.3
Controls whether RIP as a router discovery protocol is active for this local address.
OBJECT-TYPE    
  INTEGER enabled(2), disabled(1)  

ipRouterIfTable 1.3.6.1.4.1.33.10.14.2
Table of IP router values indexed by interface.
OBJECT-TYPE    
  SEQUENCE OF  
    IpRouterIfEntry

ipRouterIfEntry 1.3.6.1.4.1.33.10.14.2.1
A particular entry.
OBJECT-TYPE    
  IpRouterIfEntry  

ipRouterIfIndex 1.3.6.1.4.1.33.10.14.2.1.1
The index of the interface; same as IfIndex.
OBJECT-TYPE    
  INTEGER  

ipRouterIfProtocolPriority 1.3.6.1.4.1.33.10.14.2.1.2
The priority at which all Internet routed packets will be placed on the WAN output queue.
OBJECT-TYPE    
  INTEGER low(1), medium(3), high(5)  

ipRouterIfMTU 1.3.6.1.4.1.33.10.14.2.1.3
The size of the largest datagram that IP can transmit on this interface. The default value is actually hardware dependent.
OBJECT-TYPE    
  INTEGER 128..65535  

ipRouterIfRDP 1.3.6.1.4.1.33.10.14.2.1.4
Control for whether the router side of the Router Discovery Protocol is running on this interface.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

ipRouterIfArpPacketsIn 1.3.6.1.4.1.33.10.14.2.1.5
The number of ARP packets received on this interface.
OBJECT-TYPE    
  Counter  

ipRouterIfArpPacketsOut 1.3.6.1.4.1.33.10.14.2.1.6
The number of ARP packets sent on this interface.
OBJECT-TYPE    
  Counter  

ipRouterIfPacketsIn 1.3.6.1.4.1.33.10.14.2.1.7
The number of IP packets received on this interface.
OBJECT-TYPE    
  Counter  

ipRouterIfPacketsOut 1.3.6.1.4.1.33.10.14.2.1.8
The number of IP packets sent on this interface.
OBJECT-TYPE    
  Counter  

ipRouterIfForwardsIn 1.3.6.1.4.1.33.10.14.2.1.9
The number of IP packets received on this interface that were forwarded.
OBJECT-TYPE    
  Counter  

ipRouterIfForwardsOut 1.3.6.1.4.1.33.10.14.2.1.10
The number of IP packets sent on this interface that were forwarded.
OBJECT-TYPE    
  Counter  

xIpTraffic 1.3.6.1.4.1.33.10.14.3
OBJECT IDENTIFIER    

ipTrafficSort 1.3.6.1.4.1.33.10.14.3.1
Setting to 'execute' causes the most recent traffic information to be sorted into the ipTrafficTable. The sorting precedence is: decreasing percentage, increasing destination address, increasing source address, and increasing interface number. Setting to 'ready' has no effect.
OBJECT-TYPE    
  INTEGER ready(1), execute(2)  

ipTrafficTable 1.3.6.1.4.1.33.10.14.3.2
A list of traffic entries, sorted in the order specified by ipTrafficSort.
OBJECT-TYPE    
  SEQUENCE OF  
    IpTrafficEntry

ipTrafficEntry 1.3.6.1.4.1.33.10.14.3.2.1
A traffic entry.
OBJECT-TYPE    
  IpTrafficEntry  

ipTrafficIndex 1.3.6.1.4.1.33.10.14.3.2.1.1
Identification of this traffic entry.
OBJECT-TYPE    
  INTEGER  

ipTrafficPercent 1.3.6.1.4.1.33.10.14.3.2.1.2
The percentage of total traffic that this traffic entry represents, in tenths of a percent.
OBJECT-TYPE    
  INTEGER  

ipTrafficDstAddr 1.3.6.1.4.1.33.10.14.3.2.1.3
The destination IP address of the traffic entry.
OBJECT-TYPE    
  IpAddress  

ipTrafficSrcAddr 1.3.6.1.4.1.33.10.14.3.2.1.4
The source IP address of the traffic entry.
OBJECT-TYPE    
  IpAddress  

ipTrafficProtocol 1.3.6.1.4.1.33.10.14.3.2.1.5
The IP protocol type of the traffic entry.
OBJECT-TYPE    
  INTEGER 0..255  

ipTrafficDstPort 1.3.6.1.4.1.33.10.14.3.2.1.6
The destination TCP/UDP port of the traffic entry.
OBJECT-TYPE    
  INTEGER 0..65535  

ipTrafficSrcPort 1.3.6.1.4.1.33.10.14.3.2.1.7
The source TCP/UDP port of the traffic entry.
OBJECT-TYPE    
  INTEGER 0..65535  

ipTrafficIf 1.3.6.1.4.1.33.10.14.3.2.1.8
The inbound interface to which the traffic entry applies. This value is the same as IfIndex.
OBJECT-TYPE    
  INTEGER  

ipTrafficMonitoring 1.3.6.1.4.1.33.10.14.3.3
Control for whether the router side of the Router Discovery Protocol is running on this interface.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

xIpNetToMediaTable 1.3.6.1.4.1.33.10.14.4
iTouch extensions to the IP Address Translation Table.
OBJECT-TYPE    
  SEQUENCE OF  
    XIpNetToMediaEntry

xIpNetToMediaEntry 1.3.6.1.4.1.33.10.14.4.1
Entry parameters.
OBJECT-TYPE    
  XIpNetToMediaEntry  

xIpNetToMediaCircuit 1.3.6.1.4.1.33.10.14.4.1.1
An additional identifier for the circuit (i.e. Frame Relay DLCI or X.25 VC) which the entry extends.
OBJECT-TYPE    
  INTEGER  

xIpNetToMediaReverseArp 1.3.6.1.4.1.33.10.14.4.1.2
Whether reverse ARP is supported on this entry.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

udpBcstServerTable 1.3.6.1.4.1.33.10.15.1
Table of servers to whom UDP broadcast messages will be forwarded.
OBJECT-TYPE    
  SEQUENCE OF  
    UdpBcstServerEntry

udpBcstServerEntry 1.3.6.1.4.1.33.10.15.1.1
A particular entry.
OBJECT-TYPE    
  UdpBcstServerEntry  

udpBcstServerAddress 1.3.6.1.4.1.33.10.15.1.1.1
Internet address of the server.
OBJECT-TYPE    
  IpAddress  

udpBcstServerStatus 1.3.6.1.4.1.33.10.15.1.1.2
The status of the server. Set to 'invalid' to remove the entry.
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

udpBcstPortTable 1.3.6.1.4.1.33.10.15.2
Table of incoming UDP destination port numbers for which UDP broadcasts will be forwarded.
OBJECT-TYPE    
  SEQUENCE OF  
    UdpBcstPortEntry

udpBcstPortEntry 1.3.6.1.4.1.33.10.15.2.1
A particular entry.
OBJECT-TYPE    
  UdpBcstPortEntry  

udpBcstPort 1.3.6.1.4.1.33.10.15.2.1.1
The incoming destination UDP port number.
OBJECT-TYPE    
  INTEGER  

udpBcstPortStatus 1.3.6.1.4.1.33.10.15.2.1.2
The status of broadcast forwarding for the port. Set to 'invalid' to remove the entry.
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

udpBcstRouting 1.3.6.1.4.1.33.10.15.3
The indication of whether this entity forwards UDP broadcasts.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

xImport 1.3.6.1.4.1.33.10.16.1
OBJECT IDENTIFIER    

xExport 1.3.6.1.4.1.33.10.16.2
OBJECT IDENTIFIER    

xFilter 1.3.6.1.4.1.33.10.16.3
OBJECT IDENTIFIER    

impEgpRuleTable 1.3.6.1.4.1.33.10.16.1.1
The EGP import table.
OBJECT-TYPE    
  SEQUENCE OF  
    ImpEgpRuleEntry

impEgpRuleEntry 1.3.6.1.4.1.33.10.16.1.1.1
An EGP import rule. Each rule is keyed by the Autonomous System of the EGP neighbor and the IP network of the route learned from the neighbor. The AS can be set to a wild card as can the IP network. When a route is learned from a neighbor, the most specific import rule is applied to the route. The route is either accepted or discarded and its metrics are applied according to the rule. An exact match on the AS and IP network is the most exact rule. An exact match on the AS and a wild card match on the IP network is the 2nd most exact rule. A wild card match on the AS and an exact match on the IP network is the 3rd most exact match. Finally, a total wild card match is the least exact rule.
OBJECT-TYPE    
  ImpEgpRuleEntry  

impEgpRuleAs 1.3.6.1.4.1.33.10.16.1.1.1.1
The Autonomous System of the neighbor. The value 65535 is a wild card matching any AS number.
OBJECT-TYPE    
  INTEGER 0..65535  

impEgpRuleNetwork 1.3.6.1.4.1.33.10.16.1.1.1.2
The IP network learned from the neighbor. The value 255.255.255.255 is a wild card matching any network.
OBJECT-TYPE    
  IpAddress  

impEgpRuleAction 1.3.6.1.4.1.33.10.16.1.1.1.3
Control whether the route is learned or discarded.
OBJECT-TYPE    
  INTEGER discard(1), accept(2)  

impEgpRulePreference 1.3.6.1.4.1.33.10.16.1.1.1.4
Preference to be stored with the route. The lower preference is preferred.
OBJECT-TYPE    
  INTEGER 1..255  

impEgpRuleType 1.3.6.1.4.1.33.10.16.1.1.1.5
Type to be stored with the route. The type is based on the OSPF external type and used to help compare metrics. Type 1 is preferred over type 2.
OBJECT-TYPE    
  INTEGER 1..2  

impEgpRuleMetricAction 1.3.6.1.4.1.33.10.16.1.1.1.6
How to apply the impEgpRuleMetric field to the metric learned with the route before storing it in the routing table.
OBJECT-TYPE    
  INTEGER replace(1), increment(2), decrement(3)  

impEgpRuleMetric 1.3.6.1.4.1.33.10.16.1.1.1.7
Metric value to be applied to the metric learned learned with the route before storing it in the routing table.
OBJECT-TYPE    
  INTEGER 0..16777215  

impEgpRuleStatus 1.3.6.1.4.1.33.10.16.1.1.1.8
The status of the rule. Set to 'invalid' to remove the rule. If the all wild card rule is removed, it is automatically readded with default values.
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

impOspfRuleTable 1.3.6.1.4.1.33.10.16.1.2
The OSPF import table.
OBJECT-TYPE    
  SEQUENCE OF  
    ImpOspfRuleEntry

impOspfRuleEntry 1.3.6.1.4.1.33.10.16.1.2.1
An OSPF import rule. Each rule is keyed by the IP network of the route and the AS from which it was learned. The Ip network and the AS can both be set to a wild card. When an OSPF route is added to the routing table, the most specific import rule is applied to set the preference of the route. An exact match on the Ip network and on the AS is the most exact rule. An exact match on the IP network and a wild card match on the AS is the 2nd most exact rule. A wild card match on both the on the AS and IP network is the next and least exact rule.
OBJECT-TYPE    
  ImpOspfRuleEntry  

impOspfRuleNetwork 1.3.6.1.4.1.33.10.16.1.2.1.1
The IP network of the route. The value 255.255.255.255 is a wild card matching any network.
OBJECT-TYPE    
  IpAddress  

impOspfRulePreference 1.3.6.1.4.1.33.10.16.1.2.1.2
Preference to be stored with the route. The lower preference is preferred.
OBJECT-TYPE    
  INTEGER 1..255  

impOspfRuleStatus 1.3.6.1.4.1.33.10.16.1.2.1.3
The status of the rule. Set to 'invalid' to remove the rule. If the all wild card rule is removed, it is automatically readded with default values.
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

impRipRuleTable 1.3.6.1.4.1.33.10.16.1.3
The RIP import table.
OBJECT-TYPE    
  SEQUENCE OF  
    ImpRipRuleEntry

impRipRuleEntry 1.3.6.1.4.1.33.10.16.1.3.1
A RIP import rule. Each rule is keyed by the interface and the IP network of the route learned from the neighbor. The route is either accepted or discarded and its metrics are applied according to the rule. An exact match on the IP network is the rule that will be applied. If an exact match does not exist, the rule with the wild card IP network is used.
OBJECT-TYPE    
  ImpRipRuleEntry  

impRipRuleFromIf 1.3.6.1.4.1.33.10.16.1.3.1.1
The interface index of the interface where the rule applies, same as ifIndex.
OBJECT-TYPE    
  IpAddress  

impRipRuleNetwork 1.3.6.1.4.1.33.10.16.1.3.1.2
The IP network learned from the neighbor. The value 255.255.255.255 is a wild card matching any network.
OBJECT-TYPE    
  IpAddress  

impRipRuleAction 1.3.6.1.4.1.33.10.16.1.3.1.3
Control whether the route is learned or discarded.
OBJECT-TYPE    
  INTEGER discard(1), accept(2)  

impRipRulePreference 1.3.6.1.4.1.33.10.16.1.3.1.4
Preference to be stored with the route. The lower preference are preferred.
OBJECT-TYPE    
  INTEGER 0..255  

impRipRuleType 1.3.6.1.4.1.33.10.16.1.3.1.5
Type to be stored with the route. The type is based on the OSPF external type and used to help compare metrics. Type 1 is preferred over type 2.
OBJECT-TYPE    
  INTEGER 1..2  

impRipRuleMetricAction 1.3.6.1.4.1.33.10.16.1.3.1.6
How to apply the impRipRuleMetric field to the metric learned with the route before storing it in the routing table.
OBJECT-TYPE    
  INTEGER replace(1), increment(2), decrement(3)  

impRipRuleMetric 1.3.6.1.4.1.33.10.16.1.3.1.7
Metric value to be applied to the metric learned learned with the route before storing it in the routing table.
OBJECT-TYPE    
  INTEGER 0..16777215  

impRipRuleStatus 1.3.6.1.4.1.33.10.16.1.3.1.8
The status of the rule. Set to 'invalid' to remove the rule. If the all wild card rule is removed, it is automatically readded with default values.
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

impIsisRuleTable 1.3.6.1.4.1.33.10.16.1.4
The Isis import table.
OBJECT-TYPE    
  SEQUENCE OF  
    ImpIsisRuleEntry

impIsisRuleEntry 1.3.6.1.4.1.33.10.16.1.4.1
An Isis import rule. Each rule is keyed by the IP network of the route learned from the neighbor. The route is either accepted or discarded and its metrics are applied according to the rule. An exact match on the IP network is the rule that will be applied. If an exact match does not exist, the rule with the wild card IP network is used.
OBJECT-TYPE    
  ImpIsisRuleEntry  

impIsisRuleNetwork 1.3.6.1.4.1.33.10.16.1.4.1.1
The IP network learned from the neighbor. The value 255.255.255.255 is a wild card matching any network.
OBJECT-TYPE    
  IpAddress  

impIsisRuleAction 1.3.6.1.4.1.33.10.16.1.4.1.2
Control whether the route is learned or discarded.
OBJECT-TYPE    
  INTEGER discard(1), accept(2)  

impIsisRulePreference 1.3.6.1.4.1.33.10.16.1.4.1.3
Preference to be stored with the route. The lower preference are preferred.
OBJECT-TYPE    
  INTEGER 0..255  

impIsisRuleType 1.3.6.1.4.1.33.10.16.1.4.1.4
Type to be stored with the route. The type is based on the OSPF external type and used to help compare metrics. Type 1 is preferred over type 2.
OBJECT-TYPE    
  INTEGER 1..2  

impIsisRuleMetricAction 1.3.6.1.4.1.33.10.16.1.4.1.5
How to apply the impIsisRuleMetric field to the metric learned with the route before storing it in the routing table.
OBJECT-TYPE    
  INTEGER replace(1), increment(2), decrement(3)  

impIsisRuleMetric 1.3.6.1.4.1.33.10.16.1.4.1.6
Metric value to be applied to the metric learned learned with the route before storing it in the routing table.
OBJECT-TYPE    
  INTEGER  

impIsisRuleStatus 1.3.6.1.4.1.33.10.16.1.4.1.7
The status of the rule. Set to 'invalid' to remove the rule. If the all wild card rule is removed, it is automatically readded with default values.
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

expEgpToEgpRuleTable 1.3.6.1.4.1.33.10.16.2.1
The EGP to EGP export table.
OBJECT-TYPE    
  SEQUENCE OF  
    ExpEgpToEgpRuleEntry

expEgpToEgpRuleEntry 1.3.6.1.4.1.33.10.16.2.1.1
An EGP to EGP export rule. Each rule is keyed by the Autonomous System of the EGP neighbor, the IP network of the EGP route in the routing table, and the Autonomous System from which the route was learned. The neighbor (to) AS can be set to a wild card as can the IP network and the (from) AS. The route is either accepted to be advertised to the neighbor or discarded from being advertised, and its metric is applied according to the rule. The best match is as follows: To As IP Network From AS Rank exact exact exact 1st exact exact wild card 2nd exact wild card exact 3rd exact wild card wild card 4th wild card exact exact 5th wild card exact wild card 6th wild card wild card exact 7th wild card wild card wild card 8th
OBJECT-TYPE    
  ExpEgpToEgpRuleEntry  

expEgpToEgpRuleToAs 1.3.6.1.4.1.33.10.16.2.1.1.1
The Autonomous System of the neighbor. The value 65535 is a wild card matching any AS number.
OBJECT-TYPE    
  INTEGER 0..65535  

expEgpToEgpRuleNetwork 1.3.6.1.4.1.33.10.16.2.1.1.2
The IP network of the route in the route table. The value 255.255.255.255 is a wild card matching any network.
OBJECT-TYPE    
  IpAddress  

expEgpToEgpRuleFromAs 1.3.6.1.4.1.33.10.16.2.1.1.3
The Autonomous System of the route in the route table. The value 65535 is a wild card matching any AS number.
OBJECT-TYPE    
  INTEGER 0..65535  

expEgpToEgpRuleAction 1.3.6.1.4.1.33.10.16.2.1.1.4
Control whether the route is advertised or not.
OBJECT-TYPE    
  INTEGER hide(1), advertise(2)  

expEgpToEgpRuleMetricAction 1.3.6.1.4.1.33.10.16.2.1.1.5
How to apply the expEgpToEgpRuleMetric field to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER replace(1), increment(2), decrement(3)  

expEgpToEgpRuleMetric 1.3.6.1.4.1.33.10.16.2.1.1.6
Metric value to be applied to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER 0..16777215  

expEgpToEgpRuleStatus 1.3.6.1.4.1.33.10.16.2.1.1.7
The status of the rule. Set to 'invalid' to remove the rule. If the all wild card rule is removed, it is automatically readded with default values.
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

expOspfToEgpRuleTable 1.3.6.1.4.1.33.10.16.2.2
The OSPF to EGP export table.
OBJECT-TYPE    
  SEQUENCE OF  
    ExpOspfToEgpRuleEntry

expOspfToEgpRuleEntry 1.3.6.1.4.1.33.10.16.2.2.1
An OSPF to EGP export rule. Each rule is keyed by the Autonomous System of the EGP neighbor, the IP network of the OSPF route in the routing table, and the Autonomous System from which the route was learned. The neighbor (to) AS can be set to a wild card as can the IP network and the (from) AS. The route is either accepted to be advertised to the neighbor or discarded from being advertised, and its metric is applied according to the rule. The best match is as follows: To As IP Network From AS Rank exact exact exact 1st exact exact wild card 2nd exact wild card exact 3rd exact wild card wild card 4th wild card exact exact 5th wild card exact wild card 6th wild card wild card exact 7th wild card wild card wild card 8th
OBJECT-TYPE    
  ExpOspfToEgpRuleEntry  

expOspfToEgpRuleToAs 1.3.6.1.4.1.33.10.16.2.2.1.1
The Autonomous System of the neighbor. The value 65535 is a wild card matching any AS number.
OBJECT-TYPE    
  INTEGER 0..65535  

expOspfToEgpRuleNetwork 1.3.6.1.4.1.33.10.16.2.2.1.2
The IP network of the route in the route table. The value 255.255.255.255 is a wild card matching any network.
OBJECT-TYPE    
  IpAddress  

expOspfToEgpRuleFromAs 1.3.6.1.4.1.33.10.16.2.2.1.3
The Autonomous System of the route in the route table. Local indicates that the route was not an external OSPF route. The value 65535 is a wild card matching any AS number, and the value 65534 is for routes within the local AS.
OBJECT-TYPE    
  INTEGER 0..65535  

expOspfToEgpRuleAction 1.3.6.1.4.1.33.10.16.2.2.1.4
Control whether the route is advertised or not.
OBJECT-TYPE    
  INTEGER hide(1), advertise(2)  

expOspfToEgpRuleMetricAction 1.3.6.1.4.1.33.10.16.2.2.1.5
How to apply the expOspfToEgpRuleMetric field to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER replace(1), increment(2), decrement(3)  

expOspfToEgpRuleMetric 1.3.6.1.4.1.33.10.16.2.2.1.6
Metric value to be applied to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER 0..16777215  

expOspfToEgpRuleStatus 1.3.6.1.4.1.33.10.16.2.2.1.7
The status of the rule. Set to 'invalid' to remove the rule. If the all wild card rule is removed, it is automatically readded with default values.
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

expStaticToEgpRuleTable 1.3.6.1.4.1.33.10.16.2.3
The Static to EGP export table.
OBJECT-TYPE    
  SEQUENCE OF  
    ExpStaticToEgpRuleEntry

expStaticToEgpRuleEntry 1.3.6.1.4.1.33.10.16.2.3.1
An Static to EGP export rule. Each rule is keyed by the Autonomous System of the EGP neighbor and the IP network of the Static route in the routing table. The neighbor (to) AS can be set to a wild card as can the IP network. The route is either accepted to be advertised to the neighbor or discarded from being advertised, and its metric is applied according to the rule. The best match is as follows: To As IP Network Rank exact exact 1st exact wild card 2nd wild card exact 3rd wild card wild card 4th
OBJECT-TYPE    
  ExpStaticToEgpRuleEntry  

expStaticToEgpRuleToAs 1.3.6.1.4.1.33.10.16.2.3.1.1
The Autonomous System of the neighbor. The value 65535 is a wild card matching any AS number.
OBJECT-TYPE    
  INTEGER 0..65535  

expStaticToEgpRuleNetwork 1.3.6.1.4.1.33.10.16.2.3.1.2
The IP network of the route in the route table. The value 255.255.255.255 is a wild card matching any network.
OBJECT-TYPE    
  IpAddress  

expStaticToEgpRuleAction 1.3.6.1.4.1.33.10.16.2.3.1.3
Control whether the route is advertised or not.
OBJECT-TYPE    
  INTEGER hide(1), advertise(2)  

expStaticToEgpRuleMetricAction 1.3.6.1.4.1.33.10.16.2.3.1.4
How to apply the expStaticToEgpRuleMetric field to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER replace(1), increment(2), decrement(3)  

expStaticToEgpRuleMetric 1.3.6.1.4.1.33.10.16.2.3.1.5
Metric value to be applied to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER 0..16777215  

expStaticToEgpRuleStatus 1.3.6.1.4.1.33.10.16.2.3.1.6
The status of the rule. Set to 'invalid' to remove the rule. If the all wild card rule is removed, it is automatically readded with default values.
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

expEgpToOspfRuleTable 1.3.6.1.4.1.33.10.16.2.4
The EGP to OSPF export table.
OBJECT-TYPE    
  SEQUENCE OF  
    ExpEgpToOspfRuleEntry

expEgpToOspfRuleEntry 1.3.6.1.4.1.33.10.16.2.4.1
An EGP to OSPF export rule. Each rule is keyed by the IP network of the EGP route in the routing table, and the Autonomous System from which the route was learned. The Ip network can be set to a wild card as can the (from) AS. The route is either accepted to be advertised to the neighbor or discarded from being advertised, and its metric is applied according to the rule. The best match is as follows: IP Network From AS Rank exact exact 1st exact wild card 2nd wild card exact 3rd wild card wild card 4th
OBJECT-TYPE    
  ExpEgpToOspfRuleEntry  

expEgpToOspfRuleNetwork 1.3.6.1.4.1.33.10.16.2.4.1.1
The IP network of the route in the route table. The value 255.255.255.255 is a wild card matching any network.
OBJECT-TYPE    
  IpAddress  

expEgpToOspfRuleFromAs 1.3.6.1.4.1.33.10.16.2.4.1.2
The Autonomous System of the route in the route table. The value 65535 is a wild card matching any AS number.
OBJECT-TYPE    
  INTEGER 0..65535  

expEgpToOspfRuleAction 1.3.6.1.4.1.33.10.16.2.4.1.3
Control whether the route is advertised or not.
OBJECT-TYPE    
  INTEGER hide(1), advertise(2)  

expEgpToOspfRuleStatus 1.3.6.1.4.1.33.10.16.2.4.1.4
The status of the rule. Set to 'invalid' to remove the rule. If the all wild card rule is removed, it is automatically readded with default values.
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

expRipToEgpRuleTable 1.3.6.1.4.1.33.10.16.2.5
The Rip to EGP export table.
OBJECT-TYPE    
  SEQUENCE OF  
    ExpRipToEgpRuleEntry

expRipToEgpRuleEntry 1.3.6.1.4.1.33.10.16.2.5.1
An Rip to EGP export rule. Each rule is keyed by the Autonomous System of the EGP neighbor and the IP network of the Rip route in the routing table. The neighbor (to) AS can be set to a wild card as can the IP network. The route is either accepted to be advertised to the neighbor or discarded from being advertised, and its metric is applied according to the rule. The best match is as follows: To As IP Network Best Match Rank exact exact 1st exact wild card 2nd wild card exact 3rd wild card wild card 4th
OBJECT-TYPE    
  ExpRipToEgpRuleEntry  

expRipToEgpRuleToAs 1.3.6.1.4.1.33.10.16.2.5.1.1
The Autonomous System of the neighbor. The value 65535 is a wild card matching any AS number.
OBJECT-TYPE    
  INTEGER 0..65535  

expRipToEgpRuleNetwork 1.3.6.1.4.1.33.10.16.2.5.1.2
The IP network of the route in the route table. The value 255.255.255.255 is a wild card matching any network.
OBJECT-TYPE    
  IpAddress  

expRipToEgpRuleAction 1.3.6.1.4.1.33.10.16.2.5.1.3
Control whether the route is advertised or not.
OBJECT-TYPE    
  INTEGER hide(1), advertise(2)  

expRipToEgpRuleMetricAction 1.3.6.1.4.1.33.10.16.2.5.1.4
How to apply the expRipToEgpRuleMetric field to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER replace(1), increment(2), decrement(3)  

expRipToEgpRuleMetric 1.3.6.1.4.1.33.10.16.2.5.1.5
Metric value to be applied to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER 0..16777215  

expRipToEgpRuleStatus 1.3.6.1.4.1.33.10.16.2.5.1.6
The status of the rule. Set to 'invalid' to remove the rule. If the all wild card rule is removed, it is automatically readded with default values.
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

expRipToOspfRuleTable 1.3.6.1.4.1.33.10.16.2.6
The RIP to OSPF export table.
OBJECT-TYPE    
  SEQUENCE OF  
    ExpRipToOspfRuleEntry

expRipToOspfRuleEntry 1.3.6.1.4.1.33.10.16.2.6.1
A RIP to OSPF export rule. Each rule is keyed by the IP network of the RIP route in the routing table. The IP network can be set to a wild card. The route is either accepted to be advertised to the neighbor or discarded from being advertised, and its metric is applied according to the rule. The best match is as follows: IP Network Best Match Rank exact 1st wild card 2nd
OBJECT-TYPE    
  ExpRipToOspfRuleEntry  

expRipToOspfRuleNetwork 1.3.6.1.4.1.33.10.16.2.6.1.1
The IP network of the route in the route table. The value 255.255.255.255 is a wild card matching any network.
OBJECT-TYPE    
  IpAddress  

expRipToOspfRuleAction 1.3.6.1.4.1.33.10.16.2.6.1.2
Control whether the route is advertised or not.
OBJECT-TYPE    
  INTEGER hide(1), advertise(2)  

expRipToOspfRuleStatus 1.3.6.1.4.1.33.10.16.2.6.1.3
The status of the rule. Set to 'invalid' to remove the rule. If the all wild card rule is removed, it is automatically readded with default values.
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

expEgpToRipRuleTable 1.3.6.1.4.1.33.10.16.2.7
The EGP to RIP export table.
OBJECT-TYPE    
  SEQUENCE OF  
    ExpEgpToRipRuleEntry

expEgpToRipRuleEntry 1.3.6.1.4.1.33.10.16.2.7.1
An EGP to RIP export rule. Each rule is keyed by the Autonomous System of the EGP neighbor, the IP network of the EGP route in the routing table, and the Autonomous System from which the route was learned. The IP network can be set to a wild card as can the the from AS. The route is either accepted to be advertised to the neighbor or discarded from being advertised, and its metric is applied according to the rule. The best match is as follows: IP Network From AS Best Match Rank exact exact 1st exact wild card 2nd wild card exact 3rd wild card wild card 4th
OBJECT-TYPE    
  ExpEgpToRipRuleEntry  

expEgpToRipRuleToIf 1.3.6.1.4.1.33.10.16.2.7.1.1
The IP address of the RIP interface to which the rule applies.
OBJECT-TYPE    
  IpAddress  

expEgpToRipRuleNetwork 1.3.6.1.4.1.33.10.16.2.7.1.2
The IP network of the route in the route table. The value 255.255.255.255 is a wild card matching any network.
OBJECT-TYPE    
  IpAddress  

expEgpToRipRuleFromAs 1.3.6.1.4.1.33.10.16.2.7.1.3
The Autonomous System of the route in the route table. The value 65535 is a wild card matching any AS number.
OBJECT-TYPE    
  INTEGER 0..65535  

expEgpToRipRuleAction 1.3.6.1.4.1.33.10.16.2.7.1.4
Control whether the route is advertised or not.
OBJECT-TYPE    
  INTEGER hide(1), advertise(2)  

expEgpToRipRuleMetricAction 1.3.6.1.4.1.33.10.16.2.7.1.5
How to apply the expEgpToRipRuleMetric field to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER replace(1), increment(2), decrement(3)  

expEgpToRipRuleMetric 1.3.6.1.4.1.33.10.16.2.7.1.6
Metric value to be applied to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER 0..16777215  

expEgpToRipRuleStatus 1.3.6.1.4.1.33.10.16.2.7.1.7
The status of the rule. Set to 'invalid' to remove the rule. If the all wild card rule is removed, it is automatically readded with default values.
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

expOspfToRipRuleTable 1.3.6.1.4.1.33.10.16.2.8
The OSPF to RIP export table.
OBJECT-TYPE    
  SEQUENCE OF  
    ExpOspfToRipRuleEntry

expOspfToRipRuleEntry 1.3.6.1.4.1.33.10.16.2.8.1
An Ospf to RIP export rule. Each rule is keyed by the Autonomous System of the Ospf neighbor, the IP network of the Ospf route in the routing table, and the Autonomous System from which the route was learned. The IP network can be set to a wild card as can the the from AS. The route is either accepted to be advertised to the neighbor or discarded from being advertised, and its metric is applied according to the rule. The best match is as follows: IP Network From AS Best Match Rank exact exact 1st exact wild card 2nd wild card exact 3rd wild card wild card 4th
OBJECT-TYPE    
  ExpOspfToRipRuleEntry  

expOspfToRipRuleToIf 1.3.6.1.4.1.33.10.16.2.8.1.1
The IP address of the RIP interface to which the rule applies.
OBJECT-TYPE    
  IpAddress  

expOspfToRipRuleNetwork 1.3.6.1.4.1.33.10.16.2.8.1.2
The IP network of the route in the route table. The value 255.255.255.255 is a wild card matching any network.
OBJECT-TYPE    
  IpAddress  

expOspfToRipRuleFromAs 1.3.6.1.4.1.33.10.16.2.8.1.3
The Autonomous System of the route in the route table. The value 65535 is a wild card matching any AS number, and the value 65534 is for routes within the local AS.
OBJECT-TYPE    
  INTEGER 0..65535  

expOspfToRipRuleAction 1.3.6.1.4.1.33.10.16.2.8.1.4
Control whether the route is advertised or not.
OBJECT-TYPE    
  INTEGER hide(1), advertise(2)  

expOspfToRipRuleMetricAction 1.3.6.1.4.1.33.10.16.2.8.1.5
How to apply the expOspfToRipRuleMetric field to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER replace(1), increment(2), decrement(3)  

expOspfToRipRuleMetric 1.3.6.1.4.1.33.10.16.2.8.1.6
Metric value to be applied to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER 0..16777215  

expOspfToRipRuleStatus 1.3.6.1.4.1.33.10.16.2.8.1.7
The status of the rule. Set to 'invalid' to remove the rule. If the all wild card rule is removed, it is automatically readded with default values. The same is true for the all wild cards where the AS is set to local
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

expRipToRipRuleTable 1.3.6.1.4.1.33.10.16.2.9
The Rip to Rip export table.
OBJECT-TYPE    
  SEQUENCE OF  
    ExpRipToRipRuleEntry

expRipToRipRuleEntry 1.3.6.1.4.1.33.10.16.2.9.1
An Rip to Rip export rule. Each rule is keyed by the IP network of the Rip route in the routing table. The neighbor IP network can be set to a wild card. The route is either accepted to be advertised to the neighbor or discarded from being advertised, and its metric is applied according to the rule. The best match is as follows: IP Network Best Match Rank exact 1st wild card 2nd
OBJECT-TYPE    
  ExpRipToRipRuleEntry  

expRipToRipRuleToIf 1.3.6.1.4.1.33.10.16.2.9.1.1
The IP address of the RIP interface to which the rule applies.
OBJECT-TYPE    
  IpAddress  

expRipToRipRuleNetwork 1.3.6.1.4.1.33.10.16.2.9.1.2
The IP network of the route in the route table. The value 255.255.255.255 is a wild card matching any network.
OBJECT-TYPE    
  IpAddress  

expRipToRipRuleAction 1.3.6.1.4.1.33.10.16.2.9.1.3
Control whether the route is advertised or not.
OBJECT-TYPE    
  INTEGER hide(1), advertise(2)  

expRipToRipRuleMetricAction 1.3.6.1.4.1.33.10.16.2.9.1.4
How to apply the expRipToRipRuleMetric field to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER replace(1), increment(2), decrement(3)  

expRipToRipRuleMetric 1.3.6.1.4.1.33.10.16.2.9.1.5
Metric value to be applied to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER 0..16777215  

expRipToRipRuleStatus 1.3.6.1.4.1.33.10.16.2.9.1.6
The status of the rule. Set to 'invalid' to remove the rule. If the all wild card rule is removed, it is automatically readded with default values.
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

expStaticToRipRuleTable 1.3.6.1.4.1.33.10.16.2.10
The Static to Rip export table.
OBJECT-TYPE    
  SEQUENCE OF  
    ExpStaticToRipRuleEntry

expStaticToRipRuleEntry 1.3.6.1.4.1.33.10.16.2.10.1
An Static to Rip export rule. Each rule is keyed by the IP network of the Static route in the routing table. The neighbor IP network can be set to a wild card. The route is either accepted to be advertised to the neighbor or discarded from being advertised, and its metric is applied according to the rule. The best match is as follows: IP Network Best Match Rank exact 1st wild card 2nd
OBJECT-TYPE    
  ExpStaticToRipRuleEntry  

expStaticToRipRuleToIf 1.3.6.1.4.1.33.10.16.2.10.1.1
The IP address of the RIP interface to which the rule applies.
OBJECT-TYPE    
  IpAddress  

expStaticToRipRuleNetwork 1.3.6.1.4.1.33.10.16.2.10.1.2
The IP network of the route in the route table. The value 255.255.255.255 is a wild card matching any network.
OBJECT-TYPE    
  IpAddress  

expStaticToRipRuleAction 1.3.6.1.4.1.33.10.16.2.10.1.3
Control whether the route is advertised or not.
OBJECT-TYPE    
  INTEGER hide(1), advertise(2)  

expStaticToRipRuleMetricAction 1.3.6.1.4.1.33.10.16.2.10.1.4
How to apply the expStaticToRipRuleMetric field to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER replace(1), increment(2), decrement(3)  

expStaticToRipRuleMetric 1.3.6.1.4.1.33.10.16.2.10.1.5
Metric value to be applied to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER 0..16777215  

expStaticToRipRuleStatus 1.3.6.1.4.1.33.10.16.2.10.1.6
The status of the rule. Set to 'invalid' to remove the rule. If the all wild card rule is removed, it is automatically readded with default values.
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

expIsisToEgpRuleTable 1.3.6.1.4.1.33.10.16.2.11
The Isis to EGP export table.
OBJECT-TYPE    
  SEQUENCE OF  
    ExpIsisToEgpRuleEntry

expIsisToEgpRuleEntry 1.3.6.1.4.1.33.10.16.2.11.1
An Isis to EGP export rule. Each rule is keyed by the Autonomous System of the EGP neighbor and the IP network of the Isis route in the routing table. The neighbor (to) AS can be set to a wild card as can the IP network. The route is either accepted to be advertised to the neighbor or discarded from being advertised, and its metric is applied according to the rule. The best match is as follows: To As IP Network Best Match Rank exact exact 1st exact wild card 2nd wild card exact 3rd wild card wild card 4th .
OBJECT-TYPE    
  ExpIsisToEgpRuleEntry  

expIsisToEgpRuleToAs 1.3.6.1.4.1.33.10.16.2.11.1.1
The Autonomous System of the neighbor. The value 65535 is a wild card matching any AS number.
OBJECT-TYPE    
  INTEGER 0..65535  

expIsisToEgpRuleNetwork 1.3.6.1.4.1.33.10.16.2.11.1.2
The IP network of the route in the route table. The value 255.255.255.255 is a wild card matching any network.
OBJECT-TYPE    
  IpAddress  

expIsisToEgpRuleAction 1.3.6.1.4.1.33.10.16.2.11.1.3
Control whether the route is advertised or not.
OBJECT-TYPE    
  INTEGER hide(1), advertise(2)  

expIsisToEgpRuleMetricAction 1.3.6.1.4.1.33.10.16.2.11.1.4
How to apply the expIsisToEgpRuleMetric field to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER replace(1), increment(2), decrement(3)  

expIsisToEgpRuleMetric 1.3.6.1.4.1.33.10.16.2.11.1.5
Metric value to be applied to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER  

expIsisToEgpRuleStatus 1.3.6.1.4.1.33.10.16.2.11.1.6
The status of the rule. Set to 'invalid' to remove the rule. If the all wild card rule is removed, it is automatically readded with default values.
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

expIsisToOspfRuleTable 1.3.6.1.4.1.33.10.16.2.12
The Isis to Ospf export table.
OBJECT-TYPE    
  SEQUENCE OF  
    ExpIsisToOspfRuleEntry

expIsisToOspfRuleEntry 1.3.6.1.4.1.33.10.16.2.12.1
An Isis to Ospf export rule. Each rule is keyed by the IP network of the Isis route in the routing table. The IP network can be set to a wild card. The route is either accepted to be advertised to the neighbor or discarded from being advertised, and its metric is applied according to the rule. The best match is as follows: IP Network Best Match Rank exact 1st wild card 2nd .
OBJECT-TYPE    
  ExpIsisToOspfRuleEntry  

expIsisToOspfRuleNetwork 1.3.6.1.4.1.33.10.16.2.12.1.1
The IP network of the route in the route table. The value 255.255.255.255 is a wild card matching any network.
OBJECT-TYPE    
  IpAddress  

expIsisToOspfRuleAction 1.3.6.1.4.1.33.10.16.2.12.1.2
Control whether the route is advertised or not.
OBJECT-TYPE    
  INTEGER hide(1), advertise(2)  

expIsisToOspfRuleStatus 1.3.6.1.4.1.33.10.16.2.12.1.3
The status of the rule. Set to 'invalid' to remove the rule. If the all wild card rule is removed, it is automatically readded with default values.
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

expIsisToRipRuleTable 1.3.6.1.4.1.33.10.16.2.13
The Isis to Rip export table.
OBJECT-TYPE    
  SEQUENCE OF  
    ExpIsisToRipRuleEntry

expIsisToRipRuleEntry 1.3.6.1.4.1.33.10.16.2.13.1
An Isis to Rip export rule. Each rule is keyed by the IP network of the Isis route in the routing table. The IP network can be set to a wild card. The route is either accepted to be advertised to the neighbor or discarded from being advertised, and its metric is applied according to the rule. The best match is as follows: IP Network Best Match Rank exact 1st wild card 2nd .
OBJECT-TYPE    
  ExpIsisToRipRuleEntry  

expIsisToRipRuleToIf 1.3.6.1.4.1.33.10.16.2.13.1.1
The IP address of the RIP interface to which the rule applies.
OBJECT-TYPE    
  IpAddress  

expIsisToRipRuleNetwork 1.3.6.1.4.1.33.10.16.2.13.1.2
The IP network of the route in the route table. The value 255.255.255.255 is a wild card matching any network.
OBJECT-TYPE    
  IpAddress  

expIsisToRipRuleAction 1.3.6.1.4.1.33.10.16.2.13.1.3
Control whether the route is advertised or not.
OBJECT-TYPE    
  INTEGER hide(1), advertise(2)  

expIsisToRipRuleMetricAction 1.3.6.1.4.1.33.10.16.2.13.1.4
How to apply the expIsisToRipRuleMetric field to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER replace(1), increment(2), decrement(3)  

expIsisToRipRuleMetric 1.3.6.1.4.1.33.10.16.2.13.1.5
Metric value to be applied to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER  

expIsisToRipRuleStatus 1.3.6.1.4.1.33.10.16.2.13.1.6
The status of the rule. Set to 'invalid' to remove the rule. If the all wild card rule is removed, it is automatically readded with default values.
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

expEgpToIsisRuleTable 1.3.6.1.4.1.33.10.16.2.14
The EGP to Isis export table.
OBJECT-TYPE    
  SEQUENCE OF  
    ExpEgpToIsisRuleEntry

expEgpToIsisRuleEntry 1.3.6.1.4.1.33.10.16.2.14.1
An EGP to Isis export rule. Each rule is keyed by the Autonomous System of the EGP neighbor, the IP network of the EGP route in the routing table, and the Autonomous System from which the route was learned. The IP network can be set to a wild card as can the from AS. The route is either accepted to be advertised to the neighbor or discarded from being advertised, and its metric is applied according to the rule. The best match is as follows: IP Network From AS Best Match Rank exact exact 1st exact wild card 2nd wild card exact 3rd wild card wild card 4th .
OBJECT-TYPE    
  ExpEgpToIsisRuleEntry  

expEgpToIsisRuleNetwork 1.3.6.1.4.1.33.10.16.2.14.1.1
The IP network of the route in the route table. The value 255.255.255.255 is a wild card matching any network.
OBJECT-TYPE    
  IpAddress  

expEgpToIsisRuleFromAs 1.3.6.1.4.1.33.10.16.2.14.1.2
The Autonomous System of the route in the route table. The value 65535 is a wild card matching any AS number.
OBJECT-TYPE    
  INTEGER 0..65535  

expEgpToIsisRuleAction 1.3.6.1.4.1.33.10.16.2.14.1.3
Control whether the route is advertised or not.
OBJECT-TYPE    
  INTEGER hide(1), advertise(2)  

expEgpToIsisRuleMetricType 1.3.6.1.4.1.33.10.16.2.14.1.4
Whether to advertise the metric as Internal or External.
OBJECT-TYPE    
  INTEGER internal(1), external(2)  

expEgpToIsisRuleDefaultMetricAction 1.3.6.1.4.1.33.10.16.2.14.1.5
How to apply the expEgpToIsisDefaultRuleMetric field to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER replace(1), increment(2), decrement(3)  

expEgpToIsisRuleDefaultMetric 1.3.6.1.4.1.33.10.16.2.14.1.6
Default metric value to be applied to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER  

expEgpToIsisRuleDelayMetricAction 1.3.6.1.4.1.33.10.16.2.14.1.7
How to apply the expEgpToIsisDelayRuleMetric field to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER replace(1), increment(2), decrement(3)  

expEgpToIsisRuleDelayMetric 1.3.6.1.4.1.33.10.16.2.14.1.8
Delay metric value to be applied to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER  

expEgpToIsisRuleErrorMetricAction 1.3.6.1.4.1.33.10.16.2.14.1.9
How to apply the expEgpToIsisErrorRuleMetric field to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER replace(1), increment(2), decrement(3)  

expEgpToIsisRuleErrorMetric 1.3.6.1.4.1.33.10.16.2.14.1.10
Error metric value to be applied to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER  

expEgpToIsisRuleExpenseMetricAction 1.3.6.1.4.1.33.10.16.2.14.1.11
How to apply the expEgpToIsisExpenseRuleMetric field to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER replace(1), increment(2), decrement(3)  

expEgpToIsisRuleExpenseMetric 1.3.6.1.4.1.33.10.16.2.14.1.12
Expense metric value to be applied to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER  

expEgpToIsisRuleStatus 1.3.6.1.4.1.33.10.16.2.14.1.13
The status of the rule. Set to 'invalid' to remove the rule. If the all wild card rule is removed, it is automatically readded with default values.
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

expOspfToIsisRuleTable 1.3.6.1.4.1.33.10.16.2.15
The Ospf to Isis export table.
OBJECT-TYPE    
  SEQUENCE OF  
    ExpOspfToIsisRuleEntry

expOspfToIsisRuleEntry 1.3.6.1.4.1.33.10.16.2.15.1
An Ospf to Isis export rule. Each rule is keyed by the Autonomous System of the Ospf neighbor, the IP network of the Ospf route in the routing table, and the Autonomous System from which the route was learned. The IP network can be set to a wild card as can the the from AS. The route is either accepted to be advertised to the neighbor or discarded from being advertised, and its metric is applied according to the rule. The best match is as follows: IP Network From AS Best Match Rank exact exact 1st exact wild card 2nd wild card exact 3rd wild card wild card 4th .
OBJECT-TYPE    
  ExpOspfToIsisRuleEntry  

expOspfToIsisRuleNetwork 1.3.6.1.4.1.33.10.16.2.15.1.1
The IP network of the route in the route table. The value 255.255.255.255 is a wild card matching any network.
OBJECT-TYPE    
  IpAddress  

expOspfToIsisRuleFromAs 1.3.6.1.4.1.33.10.16.2.15.1.2
The Autonomous System of the route in the route table. The value 65535 is a wild card matching any AS number, and the value 65534 is for routes within the local AS.
OBJECT-TYPE    
  INTEGER 0..65535  

expOspfToIsisRuleAction 1.3.6.1.4.1.33.10.16.2.15.1.3
Control whether the route is advertised or not.
OBJECT-TYPE    
  INTEGER hide(1), advertise(2)  

expOspfToIsisRuleMetricType 1.3.6.1.4.1.33.10.16.2.15.1.4
Whether to advertise the metric as Internal or External.
OBJECT-TYPE    
  INTEGER internal(1), external(2)  

expOspfToIsisRuleDefaultMetricAction 1.3.6.1.4.1.33.10.16.2.15.1.5
How to apply the expOspfToIsisDefaultRuleMetric field to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER replace(1), increment(2), decrement(3)  

expOspfToIsisRuleDefaultMetric 1.3.6.1.4.1.33.10.16.2.15.1.6
Default metric value to be applied to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER  

expOspfToIsisRuleDelayMetricAction 1.3.6.1.4.1.33.10.16.2.15.1.7
How to apply the expOspfToIsisDelayRuleMetric field to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER replace(1), increment(2), decrement(3)  

expOspfToIsisRuleDelayMetric 1.3.6.1.4.1.33.10.16.2.15.1.8
Delay metric value to be applied to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER  

expOspfToIsisRuleErrorMetricAction 1.3.6.1.4.1.33.10.16.2.15.1.9
How to apply the expOspfToIsisErrorRuleMetric field to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER replace(1), increment(2), decrement(3)  

expOspfToIsisRuleErrorMetric 1.3.6.1.4.1.33.10.16.2.15.1.10
Error metric value to be applied to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER  

expOspfToIsisRuleExpenseMetricAction 1.3.6.1.4.1.33.10.16.2.15.1.11
How to apply the expOspfToIsisExpenseRuleMetric field to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER replace(1), increment(2), decrement(3)  

expOspfToIsisRuleExpenseMetric 1.3.6.1.4.1.33.10.16.2.15.1.12
Expense metric value to be applied to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER  

expOspfToIsisRuleStatus 1.3.6.1.4.1.33.10.16.2.15.1.13
The status of the rule. Set to 'invalid' to remove the rule. If the all wild card rule is removed, it is automatically readded with default values. The same is true for the all wild cards where the AS is set to local
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

expRipToIsisRuleTable 1.3.6.1.4.1.33.10.16.2.16
The Isis to Isis export table.
OBJECT-TYPE    
  SEQUENCE OF  
    ExpRipToIsisRuleEntry

expRipToIsisRuleEntry 1.3.6.1.4.1.33.10.16.2.16.1
An Isis to Isis export rule. Each rule is keyed by the IP network of the Isis route in the routing table. The neighbor IP network can be set to a wild card. The route is either accepted to be advertised to the neighbor or discarded from being advertised, and its metric is applied according to the rule. The best match is as follows: IP Network Best Match Rank exact 1st wild card 2nd .
OBJECT-TYPE    
  ExpRipToIsisRuleEntry  

expRipToIsisRuleNetwork 1.3.6.1.4.1.33.10.16.2.16.1.1
The IP network of the route in the route table. The value 255.255.255.255 is a wild card matching any network.
OBJECT-TYPE    
  IpAddress  

expRipToIsisRuleAction 1.3.6.1.4.1.33.10.16.2.16.1.2
Control whether the route is advertised or not.
OBJECT-TYPE    
  INTEGER hide(1), advertise(2)  

expRipToIsisRuleMetricType 1.3.6.1.4.1.33.10.16.2.16.1.3
Whether to advertise the metric as Internal or External.
OBJECT-TYPE    
  INTEGER internal(1), external(2)  

expRipToIsisRuleDefaultMetricAction 1.3.6.1.4.1.33.10.16.2.16.1.4
How to apply the expRipToIsisDefaultRuleMetric field to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER replace(1), increment(2), decrement(3)  

expRipToIsisRuleDefaultMetric 1.3.6.1.4.1.33.10.16.2.16.1.5
Default metric value to be applied to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER  

expRipToIsisRuleDelayMetricAction 1.3.6.1.4.1.33.10.16.2.16.1.6
How to apply the expRipToIsisDelayRuleMetric field to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER replace(1), increment(2), decrement(3)  

expRipToIsisRuleDelayMetric 1.3.6.1.4.1.33.10.16.2.16.1.7
Delay metric value to be applied to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER  

expRipToIsisRuleErrorMetricAction 1.3.6.1.4.1.33.10.16.2.16.1.8
How to apply the expRipToIsisErrorRuleMetric field to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER replace(1), increment(2), decrement(3)  

expRipToIsisRuleErrorMetric 1.3.6.1.4.1.33.10.16.2.16.1.9
Error metric value to be applied to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER  

expRipToIsisRuleExpenseMetricAction 1.3.6.1.4.1.33.10.16.2.16.1.10
How to apply the expRipToIsisExpenseRuleMetric field to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER replace(1), increment(2), decrement(3)  

expRipToIsisRuleExpenseMetric 1.3.6.1.4.1.33.10.16.2.16.1.11
Expense metric value to be applied to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER  

expRipToIsisRuleStatus 1.3.6.1.4.1.33.10.16.2.16.1.12
The status of the rule. Set to 'invalid' to remove the rule. If the all wild card rule is removed, it is automatically readded with default values.
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

expStaticToIsisRuleTable 1.3.6.1.4.1.33.10.16.2.17
The Static to Isis export table.
OBJECT-TYPE    
  SEQUENCE OF  
    ExpStaticToIsisRuleEntry

expStaticToIsisRuleEntry 1.3.6.1.4.1.33.10.16.2.17.1
An Static to Isis export rule. Each rule is keyed by the IP network of the Static route in the routing table. The neighbor IP network can be set to a wild card. The route is either accepted to be advertised to the neighbor or discarded from being advertised, and its metric is applied according to the rule. The best match is as follows: IP Network Best Match Rank exact 1st wild card 2nd .
OBJECT-TYPE    
  ExpStaticToIsisRuleEntry  

expStaticToIsisRuleNetwork 1.3.6.1.4.1.33.10.16.2.17.1.1
The IP network of the route in the route table. The value 255.255.255.255 is a wild card matching any network.
OBJECT-TYPE    
  IpAddress  

expStaticToIsisRuleAction 1.3.6.1.4.1.33.10.16.2.17.1.2
Control whether the route is advertised or not.
OBJECT-TYPE    
  INTEGER hide(1), advertise(2)  

expStaticToIsisRuleMetricType 1.3.6.1.4.1.33.10.16.2.17.1.3
Whether to advertise the metric as Internal or External.
OBJECT-TYPE    
  INTEGER internal(1), external(2)  

expStaticToIsisRuleDefaultMetricAction 1.3.6.1.4.1.33.10.16.2.17.1.4
How to apply the expStaticToIsisDefaultRuleMetric field to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER replace(1), increment(2), decrement(3)  

expStaticToIsisRuleDefaultMetric 1.3.6.1.4.1.33.10.16.2.17.1.5
Default metric value to be applied to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER  

expStaticToIsisRuleDelayMetricAction 1.3.6.1.4.1.33.10.16.2.17.1.6
How to apply the expStaticToIsisDelayRuleMetric field to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER replace(1), increment(2), decrement(3)  

expStaticToIsisRuleDelayMetric 1.3.6.1.4.1.33.10.16.2.17.1.7
Delay metric value to be applied to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER  

expStaticToIsisRuleErrorMetricAction 1.3.6.1.4.1.33.10.16.2.17.1.8
How to apply the expStaticToIsisErrorRuleMetric field to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER replace(1), increment(2), decrement(3)  

expStaticToIsisRuleErrorMetric 1.3.6.1.4.1.33.10.16.2.17.1.9
Error metric value to be applied to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER  

expStaticToIsisRuleExpenseMetricAction 1.3.6.1.4.1.33.10.16.2.17.1.10
How to apply the expStaticToIsisExpenseRuleMetric field to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER replace(1), increment(2), decrement(3)  

expStaticToIsisRuleExpenseMetric 1.3.6.1.4.1.33.10.16.2.17.1.11
Expense metric value to be applied to the metric in the route table entry before the route is advertised.
OBJECT-TYPE    
  INTEGER  

expStaticToIsisRuleStatus 1.3.6.1.4.1.33.10.16.2.17.1.12
The status of the rule. Set to 'invalid' to remove the rule. If the all wild card rule is removed, it is automatically readded with default values.
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

ipIfFilterTable 1.3.6.1.4.1.33.10.16.3.1
Table of filter entries.
OBJECT-TYPE    
  SEQUENCE OF  
    IpIfFilterEntry

ipIfFilterEntry 1.3.6.1.4.1.33.10.16.3.1.1
A particular entry.
OBJECT-TYPE    
  IpIfFilterEntry  

ipIfFilterIndex 1.3.6.1.4.1.33.10.16.3.1.1.1
The interface index with which this entry is associated. This value is the same as IfIndex.
OBJECT-TYPE    
  INTEGER  

ipIfFilterDstAddr 1.3.6.1.4.1.33.10.16.3.1.1.2
The destination IP address to use in the filter match.
OBJECT-TYPE    
  IpAddress  

ipIfFilterDstMask 1.3.6.1.4.1.33.10.16.3.1.1.3
The destination IP mask to use in the filter match.
OBJECT-TYPE    
  IpAddress  

ipIfFilterSrcAddr 1.3.6.1.4.1.33.10.16.3.1.1.4
The source IP address to use in the filter match.
OBJECT-TYPE    
  IpAddress  

ipIfFilterSrcMask 1.3.6.1.4.1.33.10.16.3.1.1.5
The source IP mask to use in the filter match.
OBJECT-TYPE    
  IpAddress  

ipIfFilterProtocol 1.3.6.1.4.1.33.10.16.3.1.1.6
The protocol to use in the filter match. The value 256 indicates any protocol.
OBJECT-TYPE    
  INTEGER 0..256  

ipIfFilterDstPort 1.3.6.1.4.1.33.10.16.3.1.1.7
The destination port to use in the filter match. This field only applies to TCP and UDP protocol packets. The value 65536 indicates any destination port.
OBJECT-TYPE    
  INTEGER 0..65536  

ipIfFilterSrcPort 1.3.6.1.4.1.33.10.16.3.1.1.8
The source port to use in the filter match. This field only applies to TCP and UDP protocol packets. The value 65536 indicates any source port.
OBJECT-TYPE    
  INTEGER 0..65536  

ipIfFilterAction 1.3.6.1.4.1.33.10.16.3.1.1.9
Control whether the packet for which this filter is the best match should be forwarded or discarded.
OBJECT-TYPE    
  INTEGER discard(1), forward(2)  

ipIfFilterStatus 1.3.6.1.4.1.33.10.16.3.1.1.10
The status of the filter entry. Set to 'invalid' to remove the entry.
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

ipFilterState 1.3.6.1.4.1.33.10.16.3.2
The indication of whether this system does IP filtering.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

ipIfFilter2Table 1.3.6.1.4.1.33.10.16.3.3
Table of filter entries.
OBJECT-TYPE    
  SEQUENCE OF  
    IpIfFilter2Entry

ipIfFilter2Entry 1.3.6.1.4.1.33.10.16.3.3.1
A particular entry.
OBJECT-TYPE    
  IpIfFilter2Entry  

ipIfFilter2Index 1.3.6.1.4.1.33.10.16.3.3.1.1
The interface index with which this entry is associated. This value is the same as IfIndex.
OBJECT-TYPE    
  INTEGER  

ipIfFilter2DstAddr 1.3.6.1.4.1.33.10.16.3.3.1.2
The destination IP address to use in the filter match.
OBJECT-TYPE    
  IpAddress  

ipIfFilter2DstMask 1.3.6.1.4.1.33.10.16.3.3.1.3
The destination IP mask to use in the filter match.
OBJECT-TYPE    
  IpAddress  

ipIfFilter2SrcAddr 1.3.6.1.4.1.33.10.16.3.3.1.4
The source IP address to use in the filter match.
OBJECT-TYPE    
  IpAddress  

ipIfFilter2SrcMask 1.3.6.1.4.1.33.10.16.3.3.1.5
The source IP mask to use in the filter match.
OBJECT-TYPE    
  IpAddress  

ipIfFilter2Protocol 1.3.6.1.4.1.33.10.16.3.3.1.6
The protocol to use in the filter match. The value 256 indicates any protocol.
OBJECT-TYPE    
  INTEGER 0..256  

ipIfFilter2DstPortStart 1.3.6.1.4.1.33.10.16.3.3.1.7
The starting destination port in a range of destination ports to use in the filter match. This field only applies to TCP and UDP protocol packets.
OBJECT-TYPE    
  INTEGER 0..65535  

ipIfFilter2SrcPortStart 1.3.6.1.4.1.33.10.16.3.3.1.8
The starting source port in a range of source ports to use in the filter match. This field only applies to TCP and UDP protocol packets.
OBJECT-TYPE    
  INTEGER 0..65535  

ipIfFilter2Action 1.3.6.1.4.1.33.10.16.3.3.1.9
Control whether the packet for which this filter is the best match should be forwarded or discarded.
OBJECT-TYPE    
  INTEGER discard(1), forward(2)  

ipIfFilter2Status 1.3.6.1.4.1.33.10.16.3.3.1.10
The status of the filter entry. Set to 'invalid' to remove the entry.
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

ipIfFilter2DstPortEnd 1.3.6.1.4.1.33.10.16.3.3.1.11
The ending destination port in a range of destination ports to use in the filter match. This field only applies to TCP and UDP protocol packets. This filed must also be greater or equal to the ipIfFilter2DstPortStart field.
OBJECT-TYPE    
  INTEGER 0..65535  

ipIfFilter2SrcPortEnd 1.3.6.1.4.1.33.10.16.3.3.1.12
The starting source port in a range of source ports to use in the filter match. This field only applies to TCP and UDP protocol packets. This filed must also be greater or equal to the ipIfFilter2SrcPortStart field.
OBJECT-TYPE    
  INTEGER 0..65535  

ipIfFilter2TcpSyn 1.3.6.1.4.1.33.10.16.3.3.1.13
The value of the TCP SYN and ACK bit to ues in the filter match. This field only applies to TCP packets. On indicates that the SYN bit is on and the ACK bit is off. Off is any other combination.
OBJECT-TYPE    
  INTEGER off(1), on(2), all(3)  

ipIfFilter2ProtocolPriority 1.3.6.1.4.1.33.10.16.3.3.1.14
Control the priority at which the packet for which this filter is the best match should be placed on the WAN output queue. None indicates that the sending interfaces protocol priority should be used.
OBJECT-TYPE    
  INTEGER low(1), medium(3), high(5), none(256)  

ripState 1.3.6.1.4.1.33.10.18.1
The indication of whether this system participates in RIP.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

ripStatus 1.3.6.1.4.1.33.10.18.2
The status of the RIP software.
OBJECT-TYPE    
  INTEGER active(1), ripDisabled(2), ipDisabled(3), noNetworksEnabled(4), noMemory(5)  

ripNetTable 1.3.6.1.4.1.33.10.18.3
Table of RIP entries.
OBJECT-TYPE    
  SEQUENCE OF  
    RipNetEntry

ripNetEntry 1.3.6.1.4.1.33.10.18.3.1
A particular entry.
OBJECT-TYPE    
  RipNetEntry  

ripNetNet 1.3.6.1.4.1.33.10.18.3.1.1
The IP Network to which this entry applies.
OBJECT-TYPE    
  IpAddress  

ripNetState 1.3.6.1.4.1.33.10.18.3.1.2
This value controls the RIP protocol on this network.
OBJECT-TYPE    
  INTEGER disabled(1), routerDiscovery(2), full(3)  

ripNetRipsIn 1.3.6.1.4.1.33.10.18.3.1.3
The number of RIP packets received from routers on this IP network.
OBJECT-TYPE    
  Counter  

ripNetRipsOut 1.3.6.1.4.1.33.10.18.3.1.4
The number of RIP packets sent to routers on this IP network.
OBJECT-TYPE    
  Counter  

ripNetAlgorithm 1.3.6.1.4.1.33.10.18.3.1.5
This value controls the RIP algorithm on this network.
OBJECT-TYPE    
  INTEGER poisonedReverse(1), splitHorizon(2)  

lpdQueueTable 1.3.6.1.4.1.33.10.19.1
A list of lpd queues on the server.
OBJECT-TYPE    
  SEQUENCE OF  
    LpdQueueEntry

lpdQueueEntry 1.3.6.1.4.1.33.10.19.1.1
Lpd parameter values plus counters for an individual lpd queue.
OBJECT-TYPE    
  LpdQueueEntry  

lpdQueueStatus 1.3.6.1.4.1.33.10.19.1.1.1
Status of this entry. Setting the value to 'invalid' invalidates the entry, corresponding directly to the CLEAR/PURGE SERVER LPD QUEUE command. Setting the value to 'valid' validates (creates) the entry, corresonding directly to the DEF/SET SERVER LPD QUEUE and lpd create commands.
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

lpdQueueName 1.3.6.1.4.1.33.10.19.1.1.2
Name of the LPD queue, case sensitive.
OBJECT-TYPE    
  DisplayString Size(1..16)  

lpdQueuePorts 1.3.6.1.4.1.33.10.19.1.1.3
List of ports assigned to the queue. An lpd queue can be associated with more than 1 port. This object corresponds to the port-list in the DEF/SET SERVER LPD QUEUE and lpc/create commands. The OCTET STRING contains a bitmap, with one bit for each port, and enough octets for all the ports on the system. Port numbers are as defined for charPortIndex in the Character MIB [11]. Corresponding bit numbers start with 1 as the high-order bit of the first octet.
OBJECT-TYPE    
  OCTET STRING Size(16)  

lpdQueueEnabled 1.3.6.1.4.1.33.10.19.1.1.4
Flag indicates if the queue is enabled. A 'disabled' queue will reject print requests from remote systems. A 'enabled' queue accepts requests for printing.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

lpdQueueLfConversion 1.3.6.1.4.1.33.10.19.1.1.5
Flag indicates if the queue is converting linefeeds to linefeeds, carriagereturns. 'lfcr' does the converion, 'lf' does not.
OBJECT-TYPE    
  INTEGER lf(1), lfcr(2)  

lpdQueueTotalJobs 1.3.6.1.4.1.33.10.19.1.1.6
The total number of jobs on the queue. This number should be equal to the number of active and waiting jobs. (lpdQueueActive + lpdQueueWaiting)
OBJECT-TYPE    
  Gauge  

lpdQueueActiveJobs 1.3.6.1.4.1.33.10.19.1.1.7
The number of active jobs on the queue. An active job is a job that has been assigned a port is in the process of receiving data from a remote host and sending it out the port.
OBJECT-TYPE    
  Gauge  

lpdQueueWaitingJobs 1.3.6.1.4.1.33.10.19.1.1.8
The number of waiting jobs on the queue. A waiting job is a job that needs a port to send its data to. This implies that the ports associated with this queue are busy.
OBJECT-TYPE    
  Gauge  

lpdQueueProcessedJobs 1.3.6.1.4.1.33.10.19.1.1.9
The total number of jobs processed by this queue since server boot.
OBJECT-TYPE    
  Counter  

lpdQueueFormFeed 1.3.6.1.4.1.33.10.19.1.1.10
A control to determine how we will send out a formfeed when printing a lpd job. formfeedafter: Send after job, formfeedbefore: Send before job, formfeednone: Send no formfeed.
OBJECT-TYPE    
  INTEGER formfeedafter(1), formfeedbefore(2), formfeednone(3)  

lpdQueueBypass 1.3.6.1.4.1.33.10.19.1.1.11
Control for a queue to bypass a LPD port which has output inhibited via flow control. Corresponds directly to the value labeled 'Bypass' in the SERVER LPD QUEUE display.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

lpdJobTable 1.3.6.1.4.1.33.10.19.2
A list of lpd jobs.
OBJECT-TYPE    
  SEQUENCE OF  
    LpdJobEntry

lpdJobEntry 1.3.6.1.4.1.33.10.19.2.1
A single lpd Job.
OBJECT-TYPE    
  LpdJobEntry  

lpdJobStatus 1.3.6.1.4.1.33.10.19.2.1.1
Status of this entry. Setting this object to 'invalid' will remove the job from the queue. Setting this object ot 'valid' has no effect since the only way to create an lpd job is with the lpd protocol.
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

lpdJobNumber 1.3.6.1.4.1.33.10.19.2.1.2
The queue relative job number for this lpd job. Job numbers are assigned as jobs are accepted onto the queue. Job numbers are reset to 1 when they reach a value greater than 1000 and the queue goes empty.
OBJECT-TYPE    
  INTEGER 1..5000  

lpdJobAssignedPort 1.3.6.1.4.1.33.10.19.2.1.3
The number of the port assigned to the lpd job.
OBJECT-TYPE    
  INTEGER 0..256  

lpdJobFileSize 1.3.6.1.4.1.33.10.19.2.1.4
The size of the file being sent from the remote system.
OBJECT-TYPE    
  INTEGER 0..2147483647  

lpdJobHostName 1.3.6.1.4.1.33.10.19.2.1.5
The name of the host sending the job.
OBJECT-TYPE    
  DisplayString Size(1..34)  

lpdJobFileName 1.3.6.1.4.1.33.10.19.2.1.6
The name of the file being sent.
OBJECT-TYPE    
  DisplayString Size(1..34)  

lpdJobState 1.3.6.1.4.1.33.10.19.2.1.7
The current state of the lpd job. A typical job transistions through the following states: initialize->waiting->assigned->printingdata-> printingcontrol->completed.
OBJECT-TYPE    
  INTEGER initialized(1), waiting(2), assigned(3), printingData(4), printingControl(5), aborted(6), completed(7), error(8), flushing(9)  

securIDServerName0 1.3.6.1.4.1.33.10.20.1
The Domain name of the first SecurID server to try when the system verifies a SecurID PASSCODE. Corresponds directly to SERVER SECURID SERVER0 and the value labeled 'SecurID Server0:' in the SERVER SECURID display.
OBJECT-TYPE    
  DisplayString Size(0..50)  

securIDServerName1 1.3.6.1.4.1.33.10.20.2
The Domain name of the second SecurID server to try when the system verifies a SecurID PASSCODE. Corresponds directly to SERVER SECURID SERVER1 and the value labeled 'SecurID Server1:' in the SERVER SECURID display.
OBJECT-TYPE    
  DisplayString Size(0..50)  

securIDServerName2 1.3.6.1.4.1.33.10.20.3
The Domain name of the third SecurID server to try when the system verifies a SecurID PASSCODE. Corresponds directly to SERVER SECURID SERVER2 and the value labeled 'SecurID Server2:' in the SERVER SECURID display.
OBJECT-TYPE    
  DisplayString Size(0..50)  

securIDServerName3 1.3.6.1.4.1.33.10.20.4
The Domain name of the fourth SecurID server to try when the system verifies a SecurID PASSCODE. Corresponds directly to SERVER SECURID SERVER3 and the value labeled 'SecurID Server3:' in the SERVER SECURID display.
OBJECT-TYPE    
  DisplayString Size(0..50)  

securIDServerName4 1.3.6.1.4.1.33.10.20.5
The Domain name of the fifth SecurID server to try when the system verifies a SecurID PASSCODE. Corresponds directly to SERVER SECURID SERVER4 and the value labeled 'SecurID Server4:' in the SERVER SECURID display.
OBJECT-TYPE    
  DisplayString Size(0..50)  

securIDMaxRetries 1.3.6.1.4.1.33.10.20.6
The maximum number of times the server will try any single SecurID server to validate a PASSCODE. Corresponds directly to SERVER SECURID ACMMAXRETRIES and the value labeled 'SecurID ACMMAXRETRIES:' in the SERVER SECURID display.
OBJECT-TYPE    
  INTEGER 1..10  

securIDBaseTimeout 1.3.6.1.4.1.33.10.20.7
The initial timeout value to be used between prompts for a SecurID PASSCODE. Corresponds directly to SERVER SECURID ACMBASETIMEOUT and the value labeled 'SecurID ACMBASETIMEOUT:' in the SERVER SECURID display.
OBJECT-TYPE    
  INTEGER 1..10  

securIDPort 1.3.6.1.4.1.33.10.20.8
The UDP port number to be used when communicating with the SecurID servers. Corresponds directly to SERVER SECURID ACM_PORT and the value labeled 'SecurID ACM_PORT:' in the SERVER SECURID display.
OBJECT-TYPE    
  INTEGER 1..32767  

securIDQueryLimit 1.3.6.1.4.1.33.10.20.9
The maximum number of times a user will be queried for a SecurID PASSCODE before being logged out. Corresponds directly to SERVER SECURID QUERY LIMIT and the value labeled 'SecurID Query Limit:' in the SERVER SECURID display.
OBJECT-TYPE    
  INTEGER 1..10  

securIDEncryptionMode 1.3.6.1.4.1.33.10.20.10
The type of encryption to use in SecurID validation. Corresponds directly to the value labeled 'Encryption Mode' in the SERVER SECURID display.
OBJECT-TYPE    
  INTEGER sdiBlockCipher(1), des(2)  

securIDInsecureLogins 1.3.6.1.4.1.33.10.20.11
The number of user logins on ports for which SecurID user verification is not enabled. Corresponds directly to the value labeled 'Logins without SecurID:' in the SERVER SECURID display.
OBJECT-TYPE    
  Counter  

securIDSecureLogins 1.3.6.1.4.1.33.10.20.12
The number of successful user logins on ports for which SecurID user verification is enabled. Corresponds directly to the value labeled 'Successful Logins:' in the SERVER SECURID display.
OBJECT-TYPE    
  Counter  

securIDSecureLoginsFailed 1.3.6.1.4.1.33.10.20.13
The number of verification failures due to incorrect PASSCODE for attempted user logins on ports for which SecurID user verification is enabled. Corresponds directly to the value labeled 'Unsuccessful Logins:' in the SERVER SECURID display.
OBJECT-TYPE    
  Counter  

securIDServerAccess0 1.3.6.1.4.1.33.10.20.14
The number of times the system successfully accessed the SecurID server0. Corresponds directly to the value labeled 'Attempts to access:', 'Server0', and 'Successful:' in the SERVER SECURID display.
OBJECT-TYPE    
  Counter  

securIDServerAccessFailed0 1.3.6.1.4.1.33.10.20.15
The number of times the system unsuccessfully accessed the SecurID server0. Corresponds directly to the value labeled 'Attempts to access:', 'Server0', and 'UnSuccessful:' in the SERVER SECURID display.
OBJECT-TYPE    
  Counter  

securIDServerAccess1 1.3.6.1.4.1.33.10.20.16
The number of times the system successfully accessed the SecurID server1. Corresponds directly to the value labeled 'Attempts to access:', 'Server1', and 'Successful:' in the SERVER SECURID display.
OBJECT-TYPE    
  Counter  

securIDServerAccessFailed1 1.3.6.1.4.1.33.10.20.17
The number of times the system unsuccessfully accessed the SecurID server1. Corresponds directly to the value labeled 'Attempts to access:', 'Server1', and 'UnSuccessful:' in the SERVER SECURID display.
OBJECT-TYPE    
  Counter  

securIDServerAccess2 1.3.6.1.4.1.33.10.20.18
The number of times the system successfully accessed the SecurID server2. Corresponds directly to the value labeled 'Attempts to access:', 'Server2', and 'Successful:' in the SERVER SECURID display.
OBJECT-TYPE    
  Counter  

securIDServerAccessFailed2 1.3.6.1.4.1.33.10.20.19
The number of times the system unsuccessfully accessed the SecurID server2. Corresponds directly to the value labeled 'Attempts to access:', 'Server2', and 'UnSuccessful:' in the SERVER SECURID display.
OBJECT-TYPE    
  Counter  

securIDServerAccess3 1.3.6.1.4.1.33.10.20.20
The number of times the system successfully accessed the SecurID server3. Corresponds directly to the value labeled 'Attempts to access:', 'Server3', and 'Successful:' in the SERVER SECURID display.
OBJECT-TYPE    
  Counter  

securIDServerAccessFailed3 1.3.6.1.4.1.33.10.20.21
The number of times the system unsuccessfully accessed the SecurID server3. Corresponds directly to the value labeled 'Attempts to access:', 'Server3', and 'UnSuccessful:' in the SERVER SECURID display.
OBJECT-TYPE    
  Counter  

securIDServerAccess4 1.3.6.1.4.1.33.10.20.22
The number of times the system successfully accessed the SecurID server4. Corresponds directly to the value labeled 'Attempts to access:', 'Server4', and 'Successful:' in the SERVER SECURID display.
OBJECT-TYPE    
  Counter  

securIDServerAccessFailed4 1.3.6.1.4.1.33.10.20.23
The number of times the system unsuccessfully accessed the SecurID server4. Corresponds directly to the value labeled 'Attempts to access:', 'Server4', and 'UnSuccessful:' in the SERVER SECURID display.
OBJECT-TYPE    
  Counter  

securIDErrorPortIndex 1.3.6.1.4.1.33.10.20.24
The index of the most recent port on which a SecurID access violation occurred. Corresponds directly to the value labeled 'Last Unsuccessful Login:' in the SERVER SECURID display.
OBJECT-TYPE    
  INTEGER 0..40  

securIDError 1.3.6.1.4.1.33.10.20.25
The error number of the most recent SecurID-related error. Corresponds directly to the value labeled 'Reason:' in the SERVER SECURID display. See iTouch documentation for a complete list of error numbers and their meaning.
OBJECT-TYPE    
  INTEGER 0..40  

securIDErrorUsername 1.3.6.1.4.1.33.10.20.26
The username associated with the most recent SecurID-related error. Corresponds directly to the value labeled 'Username:' in the SERVER SECURID display.
OBJECT-TYPE    
  DisplayString Size(0..17)  

securIDPortTable 1.3.6.1.4.1.33.10.20.27
A list of SecurID character port entries.
OBJECT-TYPE    
  SEQUENCE OF  
    SecurIDPortEntry

securIDPortEntry 1.3.6.1.4.1.33.10.20.27.1
Parameter values for a SecurID port.
OBJECT-TYPE    
  SecurIDPortEntry  

securIDPortIndex 1.3.6.1.4.1.33.10.20.27.1.1
An index value that uniquely identifies a port could relate to SecurID. The port identified by a particular value of this index is the same port as identified by charPortIndex in the Proposed Standard Internet Character MIB.
OBJECT-TYPE    
  INTEGER  

securIDPortStatus 1.3.6.1.4.1.33.10.20.27.1.2
A control indicating the level of SecurID operation on the port. Corresponds directly to PORT SECURID and the value 'SecurID' following the label 'Enabled Characteristics' in the PORT CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

sshPortTable 1.3.6.1.4.1.33.10.23.1
A list of SSH port entries
OBJECT-TYPE    
  SEQUENCE OF  
    SshPortEntry

sshPortEntry 1.3.6.1.4.1.33.10.23.1.1
Parameter values for an SSH port.
OBJECT-TYPE    
  SshPortEntry  

sshPortIndex 1.3.6.1.4.1.33.10.23.1.1.1
An index value that uniquely identifies an SSH port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the proposed standard Internet Character MIB.
OBJECT-TYPE    
  INTEGER  

sshPortIncomingTcpPort 1.3.6.1.4.1.33.10.23.1.1.2
Specifies the TCP port number used to identify the port when a SSH connection request arrives at the server. The default for a physical port is 2022 + 100 * port's physical port number. The default is 22 for virtual ports. Corresponds directly to the value labeled 'Remote Port:' in the PORT SSH CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER 1..32767  

sshPortNewlineFiltering 1.3.6.1.4.1.33.10.23.1.1.3
Translation to apply to newline sequences (CR/NULL or CR/LF) received from the network during a SSH session, before sending the newline to the character port. The value indicates which input sequence is converted to which output sequence and sent to the character port, with 'none' meaning no translation. Corresponds directly to the value labeled 'Newline Filtering:' in the PORT SSH CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER none(1), crToCrLf(2), crToCrNull(3), crLfToCr(4), crLfToCrNull(5), crNullToCr(6), crNullToCrLf(7)  

sshPortNewline 1.3.6.1.4.1.33.10.23.1.1.4
Translation to apply to newline (carriage return) received from the character port during an SSH session, before sending the newline to the remote partner. Corresponds directly to the value labeled 'Newline:' in the PORT SSH CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER none(1), crToCrLf(2), crToCrNull(3), crLfToCr(4), crLfToCrNull(5), crNullToCr(6), crNullToCrLf(7)  

sshPortTransmitBufferedTime 1.3.6.1.4.1.33.10.23.1.1.5
Number of milliseconds to wait before transmitting data received from a character port during an interactive SSH session. Corresponds directly to the value labeled 'Transmit Buffered Time:' in the PORT SSH CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER 30..1500  

sshPortRemoteProtocol 1.3.6.1.4.1.33.10.23.1.1.6
Indicates which remote protocols will be accepted at this port. Corresponds indirectly to the presence of 'Telnet' or 'SSH' under the label 'Enabled Characteristics:' in the PORT SSH CHARACTERISTICS display. If both protocols are accepted at the port, the choice of protocol is determined by which features are enabled on the server with SSH taking precedence over Telnet.
OBJECT-TYPE    
  INTEGER ssh(1), telnet(2), both(3)  

sshCipherMask 1.3.6.1.4.1.33.10.23.2
This is a list of the encryption methods supported. The OCTET STRING contains a bitmap, with one bit for each cipher type. Corresponding bit numbers start with 0 as the low-order bit of the second octet. The following bit positions are defined: none(0), des(2), tripleDes(3), and blowfish(6). Corresponds directly to the value labeled 'SSH Cipher Enabled:' in the SERVER SSH CHARACTERISTICS display.
OBJECT-TYPE    
  OCTET STRING Size(2)  

sshAuthenticationTimeout 1.3.6.1.4.1.33.10.23.3
The timeout in minutes before disconnecting if no successful authentication of SSH parties has been made. Corresponds directly to the value labeled 'Authentication Timeout:' in the SERVER SSH CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER 1..120  

sshHostKeyLength 1.3.6.1.4.1.33.10.23.4
The bit length of the SSH host encryption key. When modified, the desired change does not occur until the next system initialization. Corresponds directly to the value labeled 'Host Key Length:' in the SERVER SSH CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER 512..2048  

sshHostKeyGenerate 1.3.6.1.4.1.33.10.23.5
For a set-request with a value of generate or update, a new host key will be generated in the background. When modified with generate, the desired change does not occur until the next system initialization whereas when modified with update the change goes into effect upon completion of the new key. In response to a get-request or a get-next-request the agent will respond ready except when a host key is being created in which case the agent responds generate.
OBJECT-TYPE    
  INTEGER ready(1), generate(2), update(3)  

sshServerKeyLength 1.3.6.1.4.1.33.10.23.6
The bit length of the SSH server encryption key. The difference between the server and host key lengths should be greater than 128 bits. Corresponds directly to the value labeled 'Server Key Length:' in the SERVER SSH CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER 512..2048  

sshServerKeyTtl 1.3.6.1.4.1.33.10.23.7
The time in minutes that the server key remains valid. After this time the server key is automatically re-generated. Corresponds directly to the value labeled 'Server Key Timeout:' in the SERVER SSH CHARACTERISTICS display.
OBJECT-TYPE    
  INTEGER 30..1440  

sshServerMaxBufferSize 1.3.6.1.4.1.33.10.23.8
The size of the four buffers used by SSH for input and output. These buffers are used for data coming from the console, going to the network, coming from the network and going to the console.
OBJECT-TYPE    
  INTEGER 4096..262144