ITF-MIB-EXT

File: ITF-MIB-EXT.mib (69130 bytes)

Imported modules

RFC-1212 RFC1213-MIB RFC1155-SMI
SYSTEM-MIB ITF-MIB IANAifType-MIB
ASAM-ALARM-MIB ASAM-EQUIP-MIB

Imported symbols

OBJECT-TYPE DisplayString Counter
Gauge asam ifIndex
InterfaceIndex IANAifType AsamAlarmSeverityType
eqptHolderId

Defined Types

AsamItfSeverityFilterType  
INTEGER indeterminate(1), warning(2), minor(3), major(4), critical(5), noAlarms(254), default(255)    

AsamIfExtEntry  
SEQUENCE    
  asamIfExtCustomerId DisplayString
  asamIfExtAlmReportingSeverity AsamItfSeverityFilterType
  asamIfExtIfSpecific OBJECT IDENTIFIER

AsamIfExtAlmReportingSeverityDefaultEntry  
SEQUENCE    
  asamIfExtIfType IANAifType
  asamIfExtAlmReportingSeverityDefault AsamAlarmSeverityType

AsamShelfPhyItfSummaryEntry  
SEQUENCE    
  asamShelfPhyItfNumberChangeOccurred Counter
  asamShelfPhyItfOperStatus OCTET STRING
  asamShelfPhyItfBitmap OCTET STRING

AsamLluEntry  
SEQUENCE    
  asamLluRelayStatus AsamLluRelayStatus
  asamLluRelayActionTime Gauge
  asamLluRelayOperStatus AsamLluRelayStatus
  asamLluRelayActionTimer Gauge

AsamLluRelayStatus  
Handling of relay for Local Loop Unbundling. unbundle (1),-- unbundling LLU relay on the particular physical line mentioned by a valid physical interface ifIndex. If LLURelay is unbundled, then the line is throughconnected to an external connector allowing to connect the line to another exchange. connect(2), -- connecting LLU relay on the particular physical line mentioned by a valid physical interface ifIndex. If LLURelay state of a particular line is connected then the line is served by the LT. For a DSL line this means it will pass to the card its low and high pass filter. The effect is that DSL signal is supported by the card, the POTS/ISDN signal is brought to an external connector. connectForMelt(3), -- connecting LLU relay for Melt on the particular physical line mentioned by a valid physical interface ifIndex. If LLURelay state of a particular line is connected with Melt then the line is served by the LT and the MELT test block can be used. For a DSL line this means it will pass to the card its low and high pass filter and a MELT measurement can be performed. The effect is that DSL signal is supported by the card, the POTS/ISDN signal is not connected. disconnect(4), -- disconnecting LLU relay on the particular physical line mentioned by a valid physical interface ifIndex. If LLURelay state of a particular line is disconnected: -the line is open ended at the LT side -the MELT test block(if present) on LT is throughconnected to an external connector This particular state allows for two types of testing: -an open ended measurement can be performed at end user side -future: a MELT measurement can be performed for the external link towards another exchange(if MELT test block present) disconnectTimed(5), -- Temporarily disconnect LLU relay. After a timeout specified by asamLluRelayActionTime, the relay goes back to 'connect'
TEXTUAL-CONVENTION    
  INTEGER unbundle(1), connect(2), connectForMelt(3), disconnect(4), disconnectTimed(5)  

AsamIfExtCounterSupportEntry  
SEQUENCE    
  asamIfExtCounterIndex IANAifType
  asamifTblifDescr INTEGER
  asamifTblifMtu INTEGER
  asamifTblifSpeed INTEGER
  asamifTblifPhysAddress INTEGER
  asamifTblifAdminStatus INTEGER
  asamifTblifOperStatus INTEGER
  asamifTblifLastChange INTEGER
  asamifTblifInOctets INTEGER
  asamifTblifInUcastPkts INTEGER
  asamifTblifInNUcastPkts INTEGER
  asamifTblifInDiscards INTEGER
  asamifTblifInErrors INTEGER
  asamifTblifInUbknownProtos INTEGER
  asamifTblifOutOctets INTEGER
  asamifTblifOutUcastPkts INTEGER
  asamifTblifOutNUcastPkts INTEGER
  asamifTblifOutDiscards INTEGER
  asamifTblifOutErrors INTEGER
  asamifxTblifName INTEGER
  asamifxTblifInMulticastPkts INTEGER
  asamifxTblifInBroadcastPkts INTEGER
  asamifxTblifOutMulticastPkts INTEGER
  asamifxTblifOutBroadcastPkts INTEGER
  asamifxTblifHCInOctets INTEGER
  asamifxTblifHCInUcastPkts INTEGER
  asamifxTblifHCInMulticastPkts INTEGER
  asamifxTblifHCInBroadcastPkts INTEGER
  asamifxTblifHCOutOctets INTEGER
  asamifxTblifHCOutUcastPkts INTEGER
  asamifxTblifHCOutMulticastPkts INTEGER
  asamifxTblifHCOutBroadcastPkts INTEGER
  asamifxTblifLinkUpDownTrapEnable INTEGER
  asamifxTblifHighSpeed INTEGER
  asamifxTblifPromiscuousMode INTEGER
  asamifxTblifConnectorPresent INTEGER
  asamifxTblifAlias INTEGER
  asamifxTblifCounterDiscontinuityTime INTEGER

AsamIfIndexToExtIfIndexMappingEntry  
SEQUENCE    
  asamExtIfIndexId1 Gauge
  asamExtIfIndexId2 Gauge
  asamExtIfIndexId3 Gauge

AsamExtIfIndexToIfIndexMappingEntry  
SEQUENCE    
  asamIfIndex InterfaceIndex

AsamIfPortTypeEntry  
SEQUENCE    
  asamIfPortType INTEGER

Defined Values

asamItfMIB 1.3.6.1.4.1.637.61.1.6
OBJECT IDENTIFIER    

asamPhyItfOperStatus 1.3.6.1.4.1.637.61.1.6.1
The bitmap for the operational status of the physical interfaces. MAX_PIF: the maximum number of interface per board SLOTS: the number of slots in the system Layout: 1..MAX_PIF 1..MAX_PIF ... 1..MAX_PIF ========== ========== ========== 0 1 ... SLOTS-1 Up = 1, Down = 0 ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NA INSRVMOD: NA RANGE: NA DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: This object is not supported.
Status: obsolete Access: read-only
OBJECT-TYPE    
  OCTET STRING  

asamPhyItfBitmap 1.3.6.1.4.1.637.61.1.6.2
The bitmap for the physical interfaces. MAX_PIF: the maximum number of interface per board SLOTS: the number of slots in the system Layout: 1..MAX_PIF 1..MAX_PIF ... 1..MAX_PIF ========== ========== ========== 0 1 ... SLOTS-1 Present = 1, Not present = 0 ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NA INSRVMOD: NA RANGE: NA DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: This object is not supported.
Status: obsolete Access: read-only
OBJECT-TYPE    
  OCTET STRING  

asamPhyItfChangeOccurredTrapEnable 1.3.6.1.4.1.637.61.1.6.3
Boolean indicating wether the changeOccurredTrap should be sent or not. The trap will not be sent if the linkUpDownTrap was already sent (regardless of the value asamChangeOccurredTrapEnable). ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NA INSRVMOD: NA RANGE: NA DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: This object is not supported.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

asamPhyItfNumberChangeOccurred 1.3.6.1.4.1.637.61.1.6.4
This is a counter indicating the number of state changes of the physical line. ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: NA DEFVALUE: 0 UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

asamIfExtTable 1.3.6.1.4.1.637.61.1.6.5
An extension to the ifTable defined in ITF-MIB. ALCATEL NOTE: TABLESIZE: DEP same size as the ifTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AsamIfExtEntry

asamIfExtEntry 1.3.6.1.4.1.637.61.1.6.5.1
An entry containing management information applicable to a particular interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AsamIfExtEntry  

asamIfExtCustomerId 1.3.6.1.4.1.637.61.1.6.5.1.1
A textual string identifying the customer assigned to this interface. Following strings have a special meaning: 'reserved' : the interface is reserved by an operator; 'faulty' : the interface is indicated by an operator as being faulty; 'available': the interface has no customer assigned to it. This object is only supported for physical interfaces. ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: YES INSRVMOD: YES RANGE: NA DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

asamIfExtAlmReportingSeverity 1.3.6.1.4.1.637.61.1.6.5.1.2
This objects specifies for a certain physical interface and all interface above in the interface hierarchy the minimal severity for an alarm to be reported. If no value is provided for this object, it will obtain the value 'default', which means the actual value is as specified in the asamIfExtAlmReportingSeverityDefaultTable. ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: YES INSRVMOD: YES RANGE: NA DEFVALUE: 'default' UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-write
OBJECT-TYPE    
  AsamItfSeverityFilterType  

asamIfExtIfSpecific 1.3.6.1.4.1.637.61.1.6.5.1.3
A reference to MIB definitions specific to the particular media being used to realize the interface. If no MIB definitions specific to the particular media are available, the value should be set to the OBJECT IDENTIFIER { 0 0 }. ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: NA DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  OBJECT IDENTIFIER  

asamNextAvailablePortType 1.3.6.1.4.1.637.61.1.6.6
This object contains the ifType for which the next available physical interface can be retrieved. Only values of ifType that represent physical interfaces are allowed. ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: YES RANGE: NA DEFVALUE: xdslLine UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-write
OBJECT-TYPE    
  IANAifType  

asamNextAvailablePort 1.3.6.1.4.1.637.61.1.6.7
This object gives the next available physical interface for which the ifType is as specified in asamNextAvailablePortType. A physical interface is considered available if its asamIfExtCustomerId has the value 'available' and its internal ASAM state is 'reachable'. If no interface of the desired type is available an error (genErr) is returned when a get-request is issued for this object. ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: NA DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

asamIfExtAlmReportingSeverityDefaultTable 1.3.6.1.4.1.637.61.1.6.8
A table specifying for each of the supported interface types for asamIfExtAlmReportingSeverity its default minimal severity. ALCATEL NOTE: TABLESIZE: DEP number of supported interface types.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AsamIfExtAlmReportingSeverityDefaultEntry

asamIfExtAlmReportingSeverityDefaultEntry 1.3.6.1.4.1.637.61.1.6.8.1
An entry of the asamIfExtAlmReportingSeverityDefaultTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AsamIfExtAlmReportingSeverityDefaultEntry  

asamIfExtIfType 1.3.6.1.4.1.637.61.1.6.8.1.1
The type of the interface. ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: NA DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  IANAifType  

asamIfExtAlmReportingSeverityDefault 1.3.6.1.4.1.637.61.1.6.8.1.2
The default minimal severity for an alarm to be reported that will be used for interfaces of the type specified in asamIfExtIfType. ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: YES RANGE: 1-5 DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-write
OBJECT-TYPE    
  AsamAlarmSeverityType  

asamItfTest 1.3.6.1.4.1.637.61.1.6.9
OBJECT IDENTIFIER    

asamItfMetallicTestGroup 1.3.6.1.4.1.637.61.1.6.9.1
OBJECT IDENTIFIER    

asamItfMetallicTestTypes 1.3.6.1.4.1.637.61.1.6.9.1.1
OBJECT IDENTIFIER    

asamItfMetallicTestLimited 1.3.6.1.4.1.637.61.1.6.9.1.1.1
OBJECT IDENTIFIER    

asamItfMetallicTestTapLooped 1.3.6.1.4.1.637.61.1.6.9.1.1.2
OBJECT IDENTIFIER    

asamItfMetallicTestMonitor 1.3.6.1.4.1.637.61.1.6.9.1.1.3
OBJECT IDENTIFIER    

asamItfMetallicTestSplitAccess 1.3.6.1.4.1.637.61.1.6.9.1.1.4
OBJECT IDENTIFIER    

asamItfMetallicTestInwardOnly 1.3.6.1.4.1.637.61.1.6.9.1.1.5
OBJECT IDENTIFIER    

asamItfMetallicTestOutwardOnly 1.3.6.1.4.1.637.61.1.6.9.1.1.6
OBJECT IDENTIFIER    

asamItfMetallicTestResetTimer 1.3.6.1.4.1.637.61.1.6.9.1.1.7
OBJECT IDENTIFIER    

asamItfMetallicTestCodes 1.3.6.1.4.1.637.61.1.6.9.1.2
OBJECT IDENTIFIER    

asamItfLineNotReachable 1.3.6.1.4.1.637.61.1.6.9.1.2.1
OBJECT IDENTIFIER    

asamItfPreparingMetallicTest 1.3.6.1.4.1.637.61.1.6.9.1.2.2
OBJECT IDENTIFIER    

asamItfAnotherMetallicTestInProgress 1.3.6.1.4.1.637.61.1.6.9.1.2.3
OBJECT IDENTIFIER    

asamItfTestAppliqueNotReachable 1.3.6.1.4.1.637.61.1.6.9.1.2.4
OBJECT IDENTIFIER    

asamItfPotsSplitterNotReachable 1.3.6.1.4.1.637.61.1.6.9.1.2.5
OBJECT IDENTIFIER    

asamItfWcapNotReachable 1.3.6.1.4.1.637.61.1.6.9.1.2.6
OBJECT IDENTIFIER    

asamItfLineBusy 1.3.6.1.4.1.637.61.1.6.9.1.2.7
OBJECT IDENTIFIER    

asamItfLineAdminOperAbnormal 1.3.6.1.4.1.637.61.1.6.9.1.2.8
OBJECT IDENTIFIER    

asamItfLineAnotherLineTestInProgress 1.3.6.1.4.1.637.61.1.6.9.1.2.9
OBJECT IDENTIFIER    

asamItfTestNotPossible 1.3.6.1.4.1.637.61.1.6.9.1.2.10
OBJECT IDENTIFIER    

asamShelfPhyItfSummaryTable 1.3.6.1.4.1.637.61.1.6.10
Shelf summary table, summarizing status information of physical interfaces of boards which can be equipped within the corresponding shelf. ALCATEL NOTE: TABLESIZE: DEP number of shelves.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AsamShelfPhyItfSummaryEntry

asamShelfPhyItfSummaryEntry 1.3.6.1.4.1.637.61.1.6.10.1
An entry of the shelf physical interface summary table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AsamShelfPhyItfSummaryEntry  

asamShelfPhyItfNumberChangeOccurred 1.3.6.1.4.1.637.61.1.6.10.1.1
This is a counter indicating the number of state changes of physical lines, equipped on boards within this shelf. ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: NA DEFVALUE: 0 UNITS: state change SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

asamShelfPhyItfOperStatus 1.3.6.1.4.1.637.61.1.6.10.1.2
The bitmap for the operational status of the physical interfaces of boards which can be equipped within this shelf. MAX_PIF: the maximum number of physical interfaces per board (lines + IMA). SLOTS: the maximum number of slots within a shelf Layout: 1..MAX_PIF 1..MAX_PIF ... 1..MAX_PIF ========== ========== ========== 0 1 ... SLOTS-1 Up = 1, Down = 0. ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: DEP: #slots*#interfaces per board DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

asamShelfPhyItfBitmap 1.3.6.1.4.1.637.61.1.6.10.1.3
The bitmap for the presence of the physical interfaces of boards which can be equipped within this shelf. MAX_PIF: the maximum number of physical interfaces per board (lines + IMA). SLOTS: the maximum number of slots within a shelf Layout: 1..MAX_PIF 1..MAX_PIF ... 1..MAX_PIF ========== ========== ========== 0 1 ... SLOTS-1 Present = 1, Not present = 0. ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: DEP: #slots*#interfaces per board DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

asamLluTable 1.3.6.1.4.1.637.61.1.6.11
The Local Loop Unbundling Table. ALCATEL NOTE: TABLESIZE: DEP same size as the ifTable
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AsamLluEntry

asamLluEntry 1.3.6.1.4.1.637.61.1.6.11.1
An entry in the asamLluTable. There will be an entry for each physical interface line (xdslLine) if the corresponding board is configured/planned and if the corresponding board supports LLU, i.e. no entries are auto-created in the MIB - for boards that are not planned, - for boards that are planned but for which the HW does not support LLU. the operator cannot create an entry nor delete an entry in this table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AsamLluEntry  

asamLluRelayStatus 1.3.6.1.4.1.637.61.1.6.11.1.1
Configured administrative status of the relay. This value is kept persistent ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: YES INSRVMOD: NA RANGE: NA DEFVALUE: unbundle UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-write
OBJECT-TYPE    
  AsamLluRelayStatus  

asamLluRelayActionTime 1.3.6.1.4.1.637.61.1.6.11.1.2
The delay in tenths of seconds during which the relay will be in disconnected state before switching to connected state after asamLluRelayStatus is configured to 'disconnectTimed' ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: 0..864000 DEFVALUE: 50 UNITS: s/10 SPARSE: NA DESCR: NA
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

asamLluRelayOperStatus 1.3.6.1.4.1.637.61.1.6.11.1.3
Operational status of the relay. This represents the actual status of the relay at any time. The value 'disconnectTimed' does not apply in this context ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: NA DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  AsamLluRelayStatus  

asamLluRelayActionTimer 1.3.6.1.4.1.637.61.1.6.11.1.4
Time in tenths of seconds remaining before switching to connected state after asamLluRelayStatus is configured to 'disconnectTimed'. 0 means that the timer associated with disconnectTimed is not active. This can happen when: - asamLluRelayStatus has never been configured to 'disconnectTimed' - The timer has been configured with asamLluRelayActionTime = 0 - The timer has expired ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: 0..864000 DEFVALUE: 0 UNITS: s/10 SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

asamIfExtCounterSupportTable 1.3.6.1.4.1.637.61.1.6.12
A Table listing the supported counters for a particular interface . ALCATEL NOTE: TABLESIZE: DEP number of supported interface types.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AsamIfExtCounterSupportEntry

asamIfExtCounterSupportEntry 1.3.6.1.4.1.637.61.1.6.12.1
An entry containing list of supported counter information applicable to a particular interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AsamIfExtCounterSupportEntry  

asamIfExtCounterIndex 1.3.6.1.4.1.637.61.1.6.12.1.1
A unique non-zero value representing an interface . ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: NA DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  IANAifType  

asamifTblifDescr 1.3.6.1.4.1.637.61.1.6.12.1.2
A value of 1 indicates that this parameter is supported for the specified interface A value of 0 indicates that this parameter is not supported for the specified interface . ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: 0..1 DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

asamifTblifMtu 1.3.6.1.4.1.637.61.1.6.12.1.3
A value of 1 indicates that this parameter is supported for the specified interface A value of 0 indicates that this parameter is not supported for the specified interface . ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: 0..1 DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

asamifTblifSpeed 1.3.6.1.4.1.637.61.1.6.12.1.4
A value of 1 indicates that this parameter is supported for the specified interface A value of 0 indicates that this parameter is not supported for the specified interface . ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: 0..1 DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

asamifTblifPhysAddress 1.3.6.1.4.1.637.61.1.6.12.1.5
A value of 1 indicates that this parameter is supported for the specified interface A value of 0 indicates that this parameter is not supported for the specified interface . ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: 0..1 DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

asamifTblifAdminStatus 1.3.6.1.4.1.637.61.1.6.12.1.6
A value of 1 indicates that this parameter is supported for the specified interface A value of 0 indicates that this parameter is not supported for the specified interface . ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: 0..1 DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

asamifTblifOperStatus 1.3.6.1.4.1.637.61.1.6.12.1.7
A value of 1 indicates that this parameter is supported for the specified interface A value of 0 indicates that this parameter is not supported for the specified interface . ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: 0..1 DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

asamifTblifLastChange 1.3.6.1.4.1.637.61.1.6.12.1.8
A value of 1 indicates that this parameter is supported for the specified interface A value of 0 indicates that this parameter is not supported for the specified interface . ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: 0..1 DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

asamifTblifInOctets 1.3.6.1.4.1.637.61.1.6.12.1.9
A value of 1 indicates that this parameter is supported for the specified interface A value of 0 indicates that this parameter is not supported for the specified interface . ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: 0..1 DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

asamifTblifInUcastPkts 1.3.6.1.4.1.637.61.1.6.12.1.10
A value of 1 indicates that this parameter is supported for the specified interface A value of 0 indicates that this parameter is not supported for the specified interface . ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: 0..1 DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

asamifTblifInNUcastPkts 1.3.6.1.4.1.637.61.1.6.12.1.11
A value of 1 indicates that this parameter is supported for the specified interface A value of 0 indicates that this parameter is not supported for the specified interface . ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: 0..1 DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

asamifTblifInDiscards 1.3.6.1.4.1.637.61.1.6.12.1.12
A value of 1 indicates that this parameter is supported for the specified interface A value of 0 indicates that this parameter is not supported for the specified interface . ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: 0..1 DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

asamifTblifInErrors 1.3.6.1.4.1.637.61.1.6.12.1.13
A value of 1 indicates that this parameter is supported for the specified interface A value of 0 indicates that this parameter is not supported for the specified interface . ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: 0..1 DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

asamifTblifInUbknownProtos 1.3.6.1.4.1.637.61.1.6.12.1.14
A value of 1 indicates that this parameter is supported for the specified interface A value of 0 indicates that this parameter is not supported for the specified interface . ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: 0..1 DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

asamifTblifOutOctets 1.3.6.1.4.1.637.61.1.6.12.1.15
A value of 1 indicates that this parameter is supported for the specified interface A value of 0 indicates that this parameter is not supported for the specified interface . ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: 0..1 DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

asamifTblifOutUcastPkts 1.3.6.1.4.1.637.61.1.6.12.1.16
A value of 1 indicates that this parameter is supported for the specified interface A value of 0 indicates that this parameter is not supported for the specified interface . ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: 0..1 DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

asamifTblifOutNUcastPkts 1.3.6.1.4.1.637.61.1.6.12.1.17
A value of 1 indicates that this parameter is supported for the specified interface A value of 0 indicates that this parameter is not supported for the specified interface . ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: 0..1 DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

asamifTblifOutDiscards 1.3.6.1.4.1.637.61.1.6.12.1.18
A value of 1 indicates that this parameter is supported for the specified interface A value of 0 indicates that this parameter is not supported for the specified interface . ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: 0..1 DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

asamifTblifOutErrors 1.3.6.1.4.1.637.61.1.6.12.1.19
A value of 1 indicates that this parameter is supported for the specified interface A value of 0 indicates that this parameter is not supported for the specified interface . ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: 0..1 DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

asamifxTblifName 1.3.6.1.4.1.637.61.1.6.12.1.20
A value of 1 indicates that this parameter is supported for the specified interface A value of 0 indicates that this parameter is not supported for the specified interface . ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: 0..1 DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

asamifxTblifInMulticastPkts 1.3.6.1.4.1.637.61.1.6.12.1.21
A value of 1 indicates that this parameter is supported for the specified interface A value of 0 indicates that this parameter is not supported for the specified interface . ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: 0..1 DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

asamifxTblifInBroadcastPkts 1.3.6.1.4.1.637.61.1.6.12.1.22
A value of 1 indicates that this parameter is supported for the specified interface A value of 0 indicates that this parameter is not supported for the specified interface . ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: 0..1 DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

asamifxTblifOutMulticastPkts 1.3.6.1.4.1.637.61.1.6.12.1.23
A value of 1 indicates that this parameter is supported for the specified interface A value of 0 indicates that this parameter is not supported for the specified interface . ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: 0..1 DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

asamifxTblifOutBroadcastPkts 1.3.6.1.4.1.637.61.1.6.12.1.24
A value of 1 indicates that this parameter is supported for the specified interface A value of 0 indicates that this parameter is not supported for the specified interface . ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: 0..1 DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

asamifxTblifHCInOctets 1.3.6.1.4.1.637.61.1.6.12.1.25
A value of 1 indicates that this parameter is supported for the specified interface A value of 0 indicates that this parameter is not supported for the specified interface . ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: 0..1 DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

asamifxTblifHCInUcastPkts 1.3.6.1.4.1.637.61.1.6.12.1.26
A value of 1 indicates that this parameter is supported for the specified interface A value of 0 indicates that this parameter is not supported for the specified interface . ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: 0..1 DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

asamifxTblifHCInMulticastPkts 1.3.6.1.4.1.637.61.1.6.12.1.27
A value of 1 indicates that this parameter is supported for the specified interface A value of 0 indicates that this parameter is not supported for the specified interface . ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: 0..1 DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

asamifxTblifHCInBroadcastPkts 1.3.6.1.4.1.637.61.1.6.12.1.28
A value of 1 indicates that this parameter is supported for the specified interface A value of 0 indicates that this parameter is not supported for the specified interface . ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: 0..1 DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

asamifxTblifHCOutOctets 1.3.6.1.4.1.637.61.1.6.12.1.29
A value of 1 indicates that this parameter is supported for the specified interface A value of 0 indicates that this parameter is not supported for the specified interface . ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: 0..1 DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

asamifxTblifHCOutUcastPkts 1.3.6.1.4.1.637.61.1.6.12.1.30
A value of 1 indicates that this parameter is supported for the specified interface A value of 0 indicates that this parameter is not supported for the specified interface . ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: 0..1 DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

asamifxTblifHCOutMulticastPkts 1.3.6.1.4.1.637.61.1.6.12.1.31
A value of 1 indicates that this parameter is supported for the specified interface A value of 0 indicates that this parameter is not supported for the specified interface . ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: 0..1 DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

asamifxTblifHCOutBroadcastPkts 1.3.6.1.4.1.637.61.1.6.12.1.32
A value of 1 indicates that this parameter is supported for the specified interface A value of 0 indicates that this parameter is not supported for the specified interface . ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: 0..1 DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

asamifxTblifLinkUpDownTrapEnable 1.3.6.1.4.1.637.61.1.6.12.1.33
A value of 1 indicates that this parameter is supported for the specified interface A value of 0 indicates that this parameter is not supported for the specified interface . ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: 0..1 DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

asamifxTblifHighSpeed 1.3.6.1.4.1.637.61.1.6.12.1.34
A value of 1 indicates that this parameter is supported for the specified interface A value of 0 indicates that this parameter is not supported for the specified interface . ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: 0..1 DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

asamifxTblifPromiscuousMode 1.3.6.1.4.1.637.61.1.6.12.1.35
A value of 1 indicates that this parameter is supported for the specified interface A value of 0 indicates that this parameter is not supported for the specified interface . ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: 0..1 DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

asamifxTblifConnectorPresent 1.3.6.1.4.1.637.61.1.6.12.1.36
A value of 1 indicates that this parameter is supported for the specified interface A value of 0 indicates that this parameter is not supported for the specified interface . ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: 0..1 DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

asamifxTblifAlias 1.3.6.1.4.1.637.61.1.6.12.1.37
A value of 1 indicates that this parameter is supported for the specified interface A value of 0 indicates that this parameter is not supported for the specified interface . ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: 0..1 DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

asamifxTblifCounterDiscontinuityTime 1.3.6.1.4.1.637.61.1.6.12.1.38
A value of 1 indicates that this parameter is supported for the specified interface A value of 0 indicates that this parameter is not supported for the specified interface . ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: 0..1 DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

asamIfIndexToExtIfIndexMappingTable 1.3.6.1.4.1.637.61.1.6.13
ifIndex to extended ifIndex Mapping Table. ALCATEL NOTE: TABLESIZE: DEP same size as the ifTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AsamIfIndexToExtIfIndexMappingEntry

asamIfIndexToExtIfIndexMappingEntry 1.3.6.1.4.1.637.61.1.6.13.1
An entry containing mapping from ifIndex to extended ifIndex of interfaces.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AsamIfIndexToExtIfIndexMappingEntry  

asamExtIfIndexId1 1.3.6.1.4.1.637.61.1.6.13.1.1
Indicates the first indentifier of the extended-ifIndex INTEGER.xxxx.xxxx. ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: Gauge DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge 0..4294967295  

asamExtIfIndexId2 1.3.6.1.4.1.637.61.1.6.13.1.2
Indicates the second indentifier of the extended-ifIndex xxxx.INTEGER.xxxx. ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: Gauge DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge 0..4294967295  

asamExtIfIndexId3 1.3.6.1.4.1.637.61.1.6.13.1.3
Indicates the third indentifier of the extended-ifIndex xxxx.xxxx.INTEGER. ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: Gauge DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge 0..4294967295  

asamExtIfIndexToIfIndexMappingTable 1.3.6.1.4.1.637.61.1.6.14
Extended-ifIndex to ifIndex Mapping Table. ALCATEL NOTE: TABLESIZE: DEP same size as the ifTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AsamExtIfIndexToIfIndexMappingEntry

asamExtIfIndexToIfIndexMappingEntry 1.3.6.1.4.1.637.61.1.6.14.1
An entry containing mapping from extended-ifIndex to ifIndex of interfaces.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AsamExtIfIndexToIfIndexMappingEntry  

asamIfIndex 1.3.6.1.4.1.637.61.1.6.14.1.1
Indicates the ifIndex of the interface. ALCATEL NOTE: ACCESS: NA USAGE: NA PERSIST: NO INSRVMOD: NA RANGE: ifIndex DEFVALUE: NA UNITS: NA SPARSE: NA DESCR: NA
Status: mandatory Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

asamIfPortTypeTable 1.3.6.1.4.1.637.61.1.6.15
EFM Interface PortType Table. ALCATEL NOTE: TABLESIZE: Entry will be equivalent to number of EFM interfaces exist.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AsamIfPortTypeEntry

asamIfPortTypeEntry 1.3.6.1.4.1.637.61.1.6.15.1
An entry appears in this table for each EFM interface exist in the system.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AsamIfPortTypeEntry  

asamIfPortType 1.3.6.1.4.1.637.61.1.6.15.1.1
This object identifies the whole network service model based on this interface. User Network Interface (UNI) is an interface which specifies one untrust subscriber is connected. Network to Network Interface (NNI) is an interface which specifies one trust networks in connected. Hicap User Network Interface (HUNI) is an interface which specifies one untrust subscriber is connected, but with hicapacity services. Uplink specifies the interface is at the upside of the ISAM, i.e. connecting the ISAM to the network. Lemi is a local ethernet management interface. It is supported only on a restricted set of systems/cards. ALCATEL NOTE: ACCESS : NA USAGE : NA PERSIST: YES INSRVMOD: NA RANGE : NA DEFVALUE: uni UNITS : NA SPARSE : NA DESCR : This Object is supported only for few LTs.Setting of portType is not allowed for native ethernet interfaces.Setting portType as UNI is allowed for all interfaces except native ethernet.Setting portType as NNI is allowed only for EFM intefaces on supported LTs.For ethernet interfaces (native Ethernet) get command will display the portType from extendEtherPortCtrlTable
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER uni(1), nni(2), huni(3), uplink(4), lemi(5)