INNO-MIB

File: INNO-MIB.mib (17281 bytes)

Imported modules

RFC1155-SMI RFC-1212 RFC1213-MIB
RFC-1215

Imported symbols

Counter TimeTicks enterprises
IpAddress Gauge OBJECT-TYPE
ifIndex TRAP-TYPE

Defined Types

DisplayString  
OCTET STRING    

L2  
SEQUENCE    
  l2Label DisplayString
  l2State INTEGER
  l2Mode INTEGER
  l1Label DisplayString

L1Pri  
SEQUENCE    
  l1PriLabel DisplayString
  l1PriState INTEGER
  l1PriErrCrc4 Counter
  l1PriErrRemAlarmInd Counter
  l1PriErrSigLoss Counter
  l1PriErrAlarmInd Counter
  l1PriErrFrameAlignmentTOut Counter
  l1PriErrFrameAlignmentLoss Counter
  l1PriErrSlip Counter
  l1PriTest INTEGER

L1Bri  
SEQUENCE    
  l1BriLabel DisplayString
  l1BriState INTEGER

L3  
SEQUENCE    
  l3Label DisplayString
  l3Protocol INTEGER
  l3NumBchan INTEGER
  l3NumBchanActive Gauge
  l3CallsBoot Counter

VoiceIf  
SEQUENCE    
  voiceIfGwName DisplayString
  voiceIfType INTEGER
  voiceIfAddr IpAddress
  voiceIfState INTEGER
  voiceIfNumber DisplayString
  voiceIfName DisplayString
  voiceIfProduct DisplayString
  voiceIfIndex INTEGER
  voiceIfAliasIndex INTEGER

Defined Values

innovaphone 1.3.6.1.4.1.6666
OBJECT IDENTIFIER    

isdn 1.3.6.1.4.1.6666.1
OBJECT IDENTIFIER    

l2Table 1.3.6.1.4.1.6666.1.1
ISDN layer2 table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    L2

l2Entry 1.3.6.1.4.1.6666.1.1.1
Layer 2 Entry
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  L2  

l2Label 1.3.6.1.4.1.6666.1.1.1.1
Name of this Layer 2 instance
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..8)  

l2State 1.3.6.1.4.1.6666.1.1.1.2
Indication whether the LAPD layer is active
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER down(1), up(2)  

l2Mode 1.3.6.1.4.1.6666.1.1.1.3
Interface mode, either NT or TE
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER te(1), nt(2)  

l1Label 1.3.6.1.4.1.6666.1.1.1.4
Name of Layer 1 (physical) instance this Layer 2 instance is working on
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..8)  

l1PriTable 1.3.6.1.4.1.6666.1.2
Layer1 table (primary rate interface)
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    L1Pri

l1PriEntry 1.3.6.1.4.1.6666.1.2.1
Layer 1 Entry (primary rate interface)
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  L1Pri  

l1PriLabel 1.3.6.1.4.1.6666.1.2.1.1
Name of this Layer 1 instance
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..8)  

l1PriState 1.3.6.1.4.1.6666.1.2.1.2
Indication whether the physical layer is active
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER down(1), up(2)  

l1PriErrCrc4 1.3.6.1.4.1.6666.1.2.1.3
The CRC4 check of a received submultiframe failed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

l1PriErrRemAlarmInd 1.3.6.1.4.1.6666.1.2.1.4
Remote Alarm
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

l1PriErrSigLoss 1.3.6.1.4.1.6666.1.2.1.5
Loss of signal
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

l1PriErrAlarmInd 1.3.6.1.4.1.6666.1.2.1.6
Alarm Indication Signal
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

l1PriErrFrameAlignmentTOut 1.3.6.1.4.1.6666.1.2.1.7
Receive Time Out 400 msec
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

l1PriErrFrameAlignmentLoss 1.3.6.1.4.1.6666.1.2.1.8
Loss of Frame Alignment
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

l1PriErrSlip 1.3.6.1.4.1.6666.1.2.1.9
Receive SLIP detected
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

l1PriTest 1.3.6.1.4.1.6666.1.2.1.10
Triggers,resets some hardware alarm counters
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noTest(0), simAlarm(1), resetAlarms(2)  

l1BriTable 1.3.6.1.4.1.6666.1.3
Layer1 table (basic rate interface)
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    L1Bri

l1BriEntry 1.3.6.1.4.1.6666.1.3.1
Layer 1 Entry (basic rate rate interface)
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  L1Bri  

l1BriLabel 1.3.6.1.4.1.6666.1.3.1.1
Name of this Layer 1 instance
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..8)  

l1BriState 1.3.6.1.4.1.6666.1.3.1.2
Indication whether the physical layer is active
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER down(1), up(2)  

l3Table 1.3.6.1.4.1.6666.1.4
Layer3 table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    L3

l3Entry 1.3.6.1.4.1.6666.1.4.1
Layer 3 Entry
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  L3  

l3Label 1.3.6.1.4.1.6666.1.4.1.1
Name of this Layer 3 instance
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..8)  

l3Protocol 1.3.6.1.4.1.6666.1.4.1.2
The Isdn signalling protocol on this interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER none(0), other(1), etsi(3), qsig(23)  

l3NumBchan 1.3.6.1.4.1.6666.1.4.1.3
Number of B-channels available
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

l3NumBchanActive 1.3.6.1.4.1.6666.1.4.1.4
Number of B-channels currently active. May also be understood as number of calls currently active on this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

l3CallsBoot 1.3.6.1.4.1.6666.1.4.1.5
Accumulated Number of Calls on this interface since last Boot
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

gateway 1.3.6.1.4.1.6666.2
OBJECT IDENTIFIER    

gatekeeper 1.3.6.1.4.1.6666.2.1
OBJECT IDENTIFIER    

voiceIfTable 1.3.6.1.4.1.6666.2.1.1
Voice Interfaces Table. Features either physical interfaces or aliases.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoiceIf

voiceIfEntry 1.3.6.1.4.1.6666.2.1.1.1
Voice Interfaces Entry.Features either physical interfaces or aliases.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  VoiceIf  

voiceIfGwName 1.3.6.1.4.1.6666.2.1.1.1.1
Only of interest for aliases to show at which GWxx an alias has been/will be registered
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

voiceIfType 1.3.6.1.4.1.6666.2.1.1.1.2
The type of the interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER unkown(0), if(1), ep(2), gk(3), gw(4)  

voiceIfAddr 1.3.6.1.4.1.6666.2.1.1.1.3
ip address, only of interest if interface state is up
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

voiceIfState 1.3.6.1.4.1.6666.2.1.1.1.4
Interface state
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER down(0), up(1)  

voiceIfNumber 1.3.6.1.4.1.6666.2.1.1.1.5
The E.164 number registered by this interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

voiceIfName 1.3.6.1.4.1.6666.2.1.1.1.6
The H.323 Name registered by this interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

voiceIfProduct 1.3.6.1.4.1.6666.2.1.1.1.7
If available the description of the registering product
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

voiceIfIndex 1.3.6.1.4.1.6666.2.1.1.1.8
Increasing index of an interface, utilized as first suboid of entry index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

voiceIfAliasIndex 1.3.6.1.4.1.6666.2.1.1.1.9
If interface is an alias, this is the increasing index of alias at an interface. Otherwise -1 will be returned. Utilized as second suboid of entry index.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

trapDummyGroup 1.3.6.1.4.1.6666.3
OBJECT IDENTIFIER    

trapDisplayStringParm 1.3.6.1.4.1.6666.3.1
This variable doesn't exist. Its purpose is to be syntactically referenced as a variable within a trap.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

trapIntegerParm 1.3.6.1.4.1.6666.3.2
This variable doesn't exist. Its purpose is to be syntactically referenced as a variable within a trap.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

trapGaugeParm 1.3.6.1.4.1.6666.3.3
This variable doesn't exist. Its purpose is to be syntactically referenced as a variable within a trap.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

innoColdStart 0
An unexpected restart happened.
TRAP-TYPE    

innoWarmStart 1
The device has been reset administratively.
TRAP-TYPE    

innoLinkDown 2
An interface link went down (PPP).
TRAP-TYPE    

innoLinkUp 3
An interface link went up.
TRAP-TYPE    

innoAuthenticationFailure 4
An Snmp PDU with a wrong community string has been received.
TRAP-TYPE    

innoIsdnFailure 5
Obsoleted: This SNMP trap is no longer necessary. Meanwhile it is covered more consistently by innoDiagAlarm and innoDiagAlarmClear. Removed from on v9hf16.
TRAP-TYPE    

innoDiagAlarm 6
This trap corresponds to an alarm under Administration/Diagnostics/Alarms
TRAP-TYPE    

innoDiagAlarmClear 7
This trap corresponds to an alarm clearing under Administration/Diagnostics/Alarms
TRAP-TYPE    

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor