HUAWEI-NGADSL-LINE-MIB

File: HUAWEI-NGADSL-LINE-MIB.mib (195322 bytes)

Imported modules

HUAWEI-MIB	IF-MIB	ADSL2-LINE-MIB
SNMPv2-CONF	SNMPv2-SMI	SNMPv2-TC
HC-PerfHist-TC-MIB	HUAWEI-DEVICE-MIB

Imported symbols

huaweiUtility	ifIndex	adsl2
adsl2PMLCurrUnit	adsl2PMLHist15MUnit	adsl2PMLHist15MInterval
adsl2PMLHistInit15MInterval	adsl2PMLHist1DUnit	adsl2PMLHist1DInterval
adsl2PMLHistinit1DInterval	adsl2ChannelStatusEntry	adsl2ChAlarmConfProfileEntry
adsl2PMLineCurrEntry	adsl2PMLineCurrInitEntry	adsl2PMChCurrEntry
adsl2LineConfProfEntry	adsl2SCStatusEntry	adsl2LineEntry
adsl2ChStatusUnit	adsl2PMChCurrUnit	adsl2PMChHist15MUnit
adsl2PMChHist15MInterval	adsl2PMChHist1DUnit	adsl2PMChHist1DInterval
adsl2LConfProfProfileName	adsl2SCStatusDirection	adsl2LineAlarmConfProfileName
adsl2ChAlarmConfProfileName	adsl2ChConfProfProfileName	adsl2LineCmndConfLdsfFailReason
adsl2ChStatusActDataRate	adsl2ChStatusChannelNum	MODULE-COMPLIANCE
OBJECT-GROUP	NOTIFICATION-GROUP	MODULE-IDENTITY
Gauge32	OBJECT-TYPE	Unsigned32
Counter32	Integer32	NOTIFICATION-TYPE
TEXTUAL-CONVENTION	DateAndTime	HCPerfIntervalThreshold
HCPerfTimeElapsed	hwFrameIndex	hwSlotIndex
hwPortIndex	hwPortOperStatus	hwPortPrimaryStatus
hwPortSecondaryStatus

Defined Types

Adsl2SymbolProtection
Attributes with this syntax are configuration parameters that reference the minimum-length impulse noise protection (INP) in terms of number of symbols. The possible values are: noProtection (i.e., INP not required), halfSymbol (i.e., INP length is 1/2 symbol), and 1-16 symbols in steps of 1 symbol. Options: 1. noProtection(1) - Indicates that the INP value is 0 2. halfSymbol(2) - Indicates that the INP value is 0.5 3. singleSymbol(3) - Indicates that the INP value is 1 4. twoSymbols(4) - Indicates that the INP value is 2 5. threeSymbols(5) - Indicates that the INP value is 3 6. fourSymbols(6) - Indicates that the INP value is 4 7. fiveSymbols(7) - Indicates that the INP value is 5 8. sixSymbols(8) - Indicates that the INP value is 6 9. sevenSymbols(9) - Indicates that the INP value is 7 10.eightSymbols(10) - Indicates that the INP value is 8 11.nineSymbols(11) - Indicates that the INP value is 9 12.tenSymbols(12) - Indicates that the INP value is 10 13.elevenSymbols(13) - Indicates that the INP value is 11 14.twelveSymbols(14) - Indicates that the INP value is 12 15.thirteeSymbols(15) - Indicates that the INP value is 13 16.fourteenSymbols(16) - Indicates that the INP value is 14 17.fifteenSymbols(17) - Indicates that the INP value is 15 18.sixteenSymbols(18) - Indicates that the INP value is 16
TEXTUAL-CONVENTION
	INTEGER	noProtection(1), halfSymbol(2), singleSymbol(3), twoSymbols(4), threeSymbols(5), fourSymbols(6), fiveSymbols(7), sixSymbols(8), sevenSymbols(9), eightSymbols(10), nineSymbols(11), tenSymbols(12), elevenSymbols(13), twelveSymbols(14), thirteeSymbols(15), fourteenSymbols(16), fifteenSymbols(17), sixteenSymbols(18)

Adsl2TrellisMode
Enable and disable the trellis mode. This default value is enabled(2). Options: 1. disable(1) - Disable the trellis mode 2. enable(2) - Enable the trellis mode
TEXTUAL-CONVENTION
	INTEGER	disable(1), enable(2)

Adsl2BitSwap
Enable and disable the bit swap upstream or downstream of a line. Options: 1. disable(1) - Disable the bit swap upstream or downstream of a line 2. enable(2) - Enable the bit swap upstream or downstream of a line
TEXTUAL-CONVENTION
	INTEGER	disable(1), enable(2)

Adsl2DpboEpsd
This is a structure that represents up to 16 PSD Mask breakpoints. Each breakpoint occupies 3 octets: The first two octets hold the index of the sub-carrier associated with the breakpoint. The third octet holds the PSD reduction at the breakpoint from 0 (0dBm/Hz) to 255 (-127.5dBm/Hz) using units of 0.5dBm/Hz.Valid values are in the range 0 to 190 (0 to -95dBm/Hz). Options: 1. disable(1) 2. enable(2)
TEXTUAL-CONVENTION
	OCTET STRING	Size(0..48)

Adsl2CfgMode
The configured ADSL management mode. Options: 1. rfc2662(1) - Management model based on RFC2662 and RFC3440 2. rfc4706(2) - Management model based on RFC4706 3. tr165(3) - Management model based on TR-165
TEXTUAL-CONVENTION
	INTEGER	rfc2662(1), rfc4706(2), tr165(3)

Adsl2DataPathMode
The channel data path mode. Options: 1. atm(1) - ATM data path 2. ptm(2) - PTM data path 3. both(3) - AMT and PTM data path
TEXTUAL-CONVENTION
	INTEGER	atm(1), ptm(2), both(3)

Adsl2PhyRControl
To enable or disable the retransmission function. Options: 1. enable(1) - Enable the retransmission function 2. disable(2) - Disable the retransmission function
TEXTUAL-CONVENTION
	INTEGER	enable(1), disable(2)

Adsl2StatusRtxUsed
This parameter specifies whether G.998.4 retransmission is used in a given transmit direction. Options: 1. rtxInuse(1) - RTX in use 2. rtxUnusedModeForbidden(2) - RTX not in use, due to RTX_MODE = FORBIDDEN 3. rtxUnusedNotSupportedXtuc(3) - RTX not in use, due to not supported by the XTU-C 4. rtxUnusedNotSupportedXtur(4) - RTX not in use, due to not supported by the XTU-R 5. rtxUnusedNotSupportedXtucAndXtur(5) - RTX not in use, due to not supported by the XTU-C and XTU-R 6. invalidValue(-1) - Invalid value
TEXTUAL-CONVENTION
	INTEGER	rtxInuse(1), rtxUnusedModeForbidden(2), rtxUnusedNotSupportedXtuc(3), rtxUnusedNotSupportedXtur(4), rtxUnusedNotSupportedXtucAndXtur(5), invalidValue(-1)

Hwadsl2InitResult
Specifies the result of a full initialization attempt; the six possible result values are: noFail(0) - Successful initialization. configError(1) - Configuration failure. configNotFeasible(2) - Configuration details not supported. commFail(3) - Communication failure. noPeerAtu(4) - Peer ATU not detected. otherCause(5) - Other initialization failure reason. ginpNotSelected(6) - G.998.4 Retransmission mode was not selected while RTX_MODE = FORCED or with RTX_MODE = RTX_TESTMODE The values used are as defined in ITU-T G.997.1, paragraph 7.5.1.3
TEXTUAL-CONVENTION
	INTEGER	noFail(0), configError(1), configNotFeasible(2), commFail(3), noPeerAtu(4), otherCause(5), ginpNotSelected(6)

Adsl2RfiBand
This is a string of 4 groups of values in the following structure: Octets 0+1 - Index of start sub-carrier used in the context of a first group. Octets 2+3 - Index of end sub-carrier used in the context of a first group. Octet 4+5 - The psd value configurated in the first group Octets 6-11 - Same, for a 2nd group. This architecture continues until octets 22-23, which are associated with a 4th group.
TEXTUAL-CONVENTION
	OCTET STRING	Size(0..24)

Hwadsl2ChannelStatusEntry
SEQUENCE
	hwadsl2ChStatusPhyRrrcBits	Counter32
	hwadsl2ChStatusPhyRtxQueue	Counter32
	hwadsl2ChStatusINP	Unsigned32
	hwadsl2ChStatusRSRedundancy	Unsigned32
	hwadsl2ChStatusRSSymbols	Unsigned32
	hwadsl2ChStatusInterDepth	Unsigned32
	hwadsl2ChStatusSymbolLength	Unsigned32
	hwadsl2ChStatusRSSize	Unsigned32
	hwadsl2ChStatusActNetDataRate	Unsigned32
	hwadsl2ChStatusActINPAgainstREIN	Unsigned32

Adsl2LConfProfReferenceClockType
The various clock references for the ADSL line, represented as an enumeration. Options: 1. freeRun(1) - Indicates the local clock 2. system(2) - Indicates the system clock
TEXTUAL-CONVENTION
	INTEGER	freeRun(1), system(2)

Adsl2ProfSwitchType
The profile switch value is enable or disable. Options: 1. enable(1) - Enable the switch 2. disable(2) - Disable the switch
TEXTUAL-CONVENTION
	INTEGER	enable(1), disable(2)

Hwadsl2LineConfProfEntry
SEQUENCE
	hwadsl2LConfProfInmIatoDs	Unsigned32
	hwadsl2LConfProfInmIatsDs	Unsigned32
	hwadsl2LConfProfInmCcDs	Unsigned32
	hwadsl2LConfProfInmInpeqModeDs	Unsigned32
	hwadsl2LConfProfRfiBands	Adsl2RfiBand
	hwadsl2LConfProfReferenceClock	Adsl2LConfProfReferenceClockType
	hwadsl2LConfProfL3Time	Unsigned32
	hwadsl2LConfProfDpboEselMin	Unsigned32
	hwadsl2LConfProfTrellisMode	Adsl2TrellisMode
	hwadsl2LConfProfBitSwapDs	Adsl2BitSwap
	hwadsl2LConfProfBitSwapUs	Adsl2BitSwap
	hwadsl2LConfProfDpboEPsd	Adsl2DpboEpsd
	hwadsl2LConfProfDpboEsEL	Unsigned32
	hwadsl2LConfProfDpboEsCableModelA	Unsigned32
	hwadsl2LConfProfDpboEsCableModelB	Unsigned32
	hwadsl2LConfProfDpboEsCableModelC	Unsigned32
	hwadsl2LConfProfDpboMus	Unsigned32
	hwadsl2LConfProfDpboFMin	Unsigned32
	hwadsl2LConfProfDpboFMax	Unsigned32

Hwadsl2ChConfProfileEntry
SEQUENCE
	hwadsl2ChConfProfDataPathMode	Adsl2DataPathMode
	hwadsl2ChConfProfErasureDecoding	Adsl2ProfSwitchType
	hwadsl2ChConfProfPhyRcontrolDs	Adsl2PhyRControl
	hwadsl2ChConfProfPhyRcontrolUs	Adsl2PhyRControl
	hwadsl2ChConfProfInpMaxDs	Adsl2SymbolProtection
	hwadsl2ChConfProfInpMaxUs	Adsl2SymbolProtection
	hwadsl2ChConfProfMinRtxRatioDs	Unsigned32
	hwadsl2ChConfProfMinRtxRatioUs	Unsigned32
	hwadsl2ChConfProfMinRSoverheadDs	Unsigned32
	hwadsl2ChConfProfMinRSoverheadUs	Unsigned32

Hwadsl2PMLineCurrEntry
SEQUENCE
	hwadsl2PMLCurr15MInmainpeq	OCTET STRING
	hwadsl2PMLCurr15MInmame	Counter32
	hwadsl2PMLCurr15MInmaiat	OCTET STRING
	hwadsl2PMLCurr1DayInmainpeq	OCTET STRING
	hwadsl2PMLCurr1DayInmame	Counter32
	hwadsl2PMLCurr1DayInmaiat	OCTET STRING
	hwadsl2PMLEverBeforeInmainpeq	OCTET STRING
	hwadsl2PMLEverBeforeInmame	Counter32
	hwadsl2PMLEverBeforeInmaiat	OCTET STRING
	hwadsl2PMLEverBeforeFecs	Counter32
	hwadsl2PMLEverBeforeEs	Counter32
	hwadsl2PMLEverBeforeSes	Counter32
	hwadsl2PMLEverBeforeLoss	Counter32
	hwadsl2PMLEverBeforeUas	Counter32
	hwadsl2PMLCurr15MStartTime	DateAndTime
	hwadsl2PMLCurr1DayStartTime	DateAndTime
	hwadsl2PMLCurr15MLofs	Counter32
	hwadsl2PMLCurr15MLols	Counter32
	hwadsl2PMLCurr15MLops	Counter32
	hwadsl2PMLCurr1DayLofs	Counter32
	hwadsl2PMLCurr1DayLols	Counter32
	hwadsl2PMLCurr1DayLops	Counter32
	hwadsl2PMLEverBeforeLofs	Counter32
	hwadsl2PMLEverBeforeLols	Counter32
	hwadsl2PMLEverBeforeLops	Counter32
	hwadsl2PMLCurr15MLeftrs	Counter32
	hwadsl2PMLCurr15MEfb	Counter32
	hwadsl2PMLCurr15MMinEftr	Counter32
	hwadsl2PMLCurr1DayLeftrs	Counter32
	hwadsl2PMLCurr1DayEfb	Counter32
	hwadsl2PMLCurr1DayMinEftr	Counter32
	hwadsl2PMLEverBeforeLeftrs	Counter32
	hwadsl2PMLEverBeforeEfb	Counter32
	hwadsl2PMLEverBeforeMinEftr	Counter32

Hwadsl2PMLineHist15MinEntry
SEQUENCE
	hwadsl2PMLHist15MInmainpeq	OCTET STRING
	hwadsl2PMLHist15MInmame	Counter32
	hwadsl2PMLHist15MInmaiat	OCTET STRING
	hwadsl2PMLHist15MStartTime	DateAndTime
	hwadsl2PMLHist15MLofs	Counter32
	hwadsl2PMLHist15MLols	Counter32
	hwadsl2PMLHist15MLops	Counter32
	hwadsl2PMLHist15MLeftrs	Counter32
	hwadsl2PMLHist15MEfb	Counter32
	hwadsl2PMLHist15MMinEftr	Counter32

Hwadsl2PMLineHist1DayEntry
SEQUENCE
	hwadsl2PMLHist1DayInmainpeq	OCTET STRING
	hwadsl2PMLHist1DayInmame	Counter32
	hwadsl2PMLHist1DayInmaiat	OCTET STRING
	hwadsl2PMLHist1DayStartTime	DateAndTime
	hwadsl2PMLHist1DayLofs	Counter32
	hwadsl2PMLHist1DayLols	Counter32
	hwadsl2PMLHist1DayLops	Counter32
	hwadsl2PMLHist1DLeftrs	Counter32
	hwadsl2PMLHist1DEfb	Counter32
	hwadsl2PMLHist1DMinEftr	Counter32

Hwadsl2PMLineCurrInitEntry
SEQUENCE
	hwadsl2PMLInitEverBeforeFullInits	Unsigned32
	hwadsl2PMLInitEverBeforeFailedFullInits	Unsigned32
	hwadsl2PMLInitEverBeforeShortInits	Unsigned32
	hwadsl2PMLInitEverBeforeFailedShortInits	Unsigned32
	hwadsl2PMLineCurrInit15MStartTime	DateAndTime
	hwadsl2PMLineCurrInit1DayStartTime	DateAndTime

Hwadsl2PMLineInitHist15MinEntry
SEQUENCE
	hwadsl2PMLineInitHist15MinStartTime	DateAndTime

Hwadsl2PMLineInitHist1DayEntry
SEQUENCE
	hwadsl2PMLineInitHist1DayStartTime	DateAndTime

Hwadsl2PMChCurrEntry
SEQUENCE
	hwadsl2PMChCurr15MRtxCW	Counter32
	hwadsl2PMChCurr15MRtxCorrectedCW	Counter32
	hwadsl2PMChCurr15MRtxUncorrectedCW	Counter32
	hwadsl2PMChCurr1DayRtxCW	Counter32
	hwadsl2PMChCurr1DayRtxCorrectedCW	Counter32
	hwadsl2PMChCurr1DayRtxUncorrectedCW	Counter32
	hwadsl2PMChEverBeforeRtxCW	Counter32
	hwadsl2PMChEverBeforeRtxCorrectedCW	Counter32
	hwadsl2PMChEverBeforeRtxUncorrectedCW	Counter32
	hwadsl2PMChEverBeforeCodingViolations	Unsigned32
	hwadsl2PMChEverBeforeCorrectedBlocks	Unsigned32
	hwadsl2PMChCur15MStartTime	DateAndTime
	hwadsl2PMChCur1DayStartTime	DateAndTime

Hwadsl2PMChHist15MinEntry
SEQUENCE
	hwadsl2PMChHist15MRtxCW	Counter32
	hwadsl2PMChHist15MRtxCorrectedCW	Counter32
	hwadsl2PMChHist15MRtxUncorrectedCW	Counter32
	hwadsl2PMChHist15MStartTime	DateAndTime

Hwadsl2PMChHist1DEntry
SEQUENCE
	hwadsl2PMChHist1DRtxCW	Counter32
	hwadsl2PMChHist1DRtxCorrectedCW	Counter32
	hwadsl2PMChHist1DRtxUncorrectedCW	Counter32
	hwadsl2PMChHist1DStartTime	DateAndTime

Hwadsl2LineEntry
SEQUENCE
	hwadsl2LineStatusCodingGainDsInfo	Unsigned32
	hwadsl2LineStatusCodingGainUsInfo	Unsigned32
	hwadsl2LineStatusPcbDsInfo	Unsigned32
	hwadsl2LineStatusPcbUsInfo	Unsigned32
	hwadsl2DynamicprofileInfo	OCTET STRING
	hwadsl2LineStatusInitResult	Hwadsl2InitResult
	hwadsl2LineStatusRtxUsedDs	Adsl2StatusRtxUsed
	hwadsl2LineStatusLastRetrainInfo	INTEGER
	hwadsl2LineStatusLineRateDs	Unsigned32
	hwadsl2LineStatusLineRateUs	Unsigned32

Hwadsl2SCStatusEntry
SEQUENCE
	hwadsl2SCStatusInfoTxPSD	OCTET STRING
	hwadsl2SCStatusInfoSnrMargins	OCTET STRING

Hwadsl2ChAlarmConfProfileEntry
SEQUENCE
	hwadsl2ChAlarmConfProfileMonitoringRateDs	Unsigned32
	hwadsl2ChAlarmConfProfileMonitoringRateUs	Unsigned32

Hwadsl2LineAlarmConfProfileEntry
SEQUENCE
	hwadsl2LineAlarmConfProfileXturThresh15MinLeftrs	HCPerfIntervalThreshold
	hwAdsl2LineAlarmConfProfileDyingGaspAlarmSwitch	INTEGER
	hwAdsl2LineAlarmConfProfileActiveFailAlarmSwitch	INTEGER

Defined Values

hwadsl2MIB		1.3.6.1.4.1.2011.6.138
The MIB is used for defining HUAWEI NGADSL LINE MIB objects, which expand from RFC4706 ADSL2-LINE MIB.
MODULE-IDENTITY

adsl2Mode		1.3.6.1.4.1.2011.2.25.238.1.65535
OBJECT IDENTIFIER

adsl2ChStatusINP		1.3.6.1.4.1.2011.2.25.238.1.2.1.1.65535
The actual impulse noise protection (INP) on the bearer channel in L0 state. Unit: 0.1 DMT symbol
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..254

adsl2ChStatusRSRedundancy		1.3.6.1.4.1.2011.2.25.238.1.2.1.1.65536
The actual number of Reed-Solomon redundancy bytes per codeword used in the latency path in which the bearer channel is transported. The value is coded in bytes. The value 0 indicates no Reed-Solomon coding. Unit: byte
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..16

adsl2ChStatusRSSymbols		1.3.6.1.4.1.2011.2.25.238.1.2.1.1.65537
The DMT Symbol number per codeword used in the latency path in which the bearer channel is transported. Unit: 0.01 DMT symbol
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

adsl2ChStatusInterDepth		1.3.6.1.4.1.2011.2.25.238.1.2.1.1.65538
The actual Reed-Solomon codeword size used in the latency path in which the bearer channel is transported. The value ranges from 1 to 4096 by step of 1. The value 1 indicates no interleaving.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	1..4096

adsl2ChStatusSymbolLength		1.3.6.1.4.1.2011.2.25.238.1.2.1.1.65539
The actual number of bits per symbol assigned to the latency path in which the bearer channel is transported. This value does not include trellis overhead. Unit: bit
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..65535

adsl2ChStatusRSSize		1.3.6.1.4.1.2011.2.25.238.1.2.1.1.65540
The actual Reed-Solomon codeword size used in the latency path in which the bearer channel is transported. Unit: byte
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..255

adsl2ChAlarmConfProfileMonitoringRateDs		1.3.6.1.4.1.2011.2.25.238.1.5.3.3.1.65535
The channel monitoring rate downstream. When the value you set is larger than the value of the rate downstream defined in the channel profile, it will not be successful. The value 0 means that no threshold is specified for the associated counter. This object is defaulted 0. Unit: bits/second
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..200000000

adsl2ChAlarmConfProfileMonitoringRateUs		1.3.6.1.4.1.2011.2.25.238.1.5.3.3.1.65536
The channel monitoring rate upstream. When the value you set is larger than the value of the rate upstream defined in the channel profile, it will not be successful. The value 0 means that no threshold is specified for the associated counter. This object is defaulted 0. Unit: bits/second
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..200000000

adsl2PMLEverBeforeFecs		1.3.6.1.4.1.2011.2.25.238.1.4.1.1.1.65535
Count of seconds since agent reset that there was at least one FEC correction event for one or more bearer channels in this line. This parameter is inhibited during UAS or SES. Unit: seconds
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

adsl2PMLEverBeforeEs		1.3.6.1.4.1.2011.2.25.238.1.4.1.1.1.65536
Count of seconds since agent reset that there was: ATU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 ATU-R: FEBE >= 1 for one or more bearer channels OR LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1. This parameter is inhibited during UAS. Unit: seconds
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

adsl2PMLEverBeforeSes		1.3.6.1.4.1.2011.2.25.238.1.4.1.1.1.65537
Count of seconds since agent reset that there was: ATU-C: (CRC-8 summed over all bearer channels) >= 18 OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 ATU-R: (FEBE summed over all bearer channels) >= 18 OR LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1 This parameter is inhibited during UAS. Unit: seconds
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

adsl2PMLEverBeforeLoss		1.3.6.1.4.1.2011.2.25.238.1.4.1.1.1.65538
Count of seconds since agent reset that there was LOS (or LOS-FE for ATU-R). Unit: seconds
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

adsl2PMLEverBeforeUas		1.3.6.1.4.1.2011.2.25.238.1.4.1.1.1.65539
Count of seconds in Unavailability State since agent reset. Unavailability begins at the onset of 10 contiguous severely -errored seconds, and ends at the onset of 10 contiguous seconds with no severely-errored seconds. Unit: seconds
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

adsl2PMLInitEverBeforeFullInits		1.3.6.1.4.1.2011.2.25.238.1.4.1.2.1.65535
Count of full initializations attempted on the line (successful and failed) since agent reset.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

adsl2PMLInitEverBeforeFailedFullInits		1.3.6.1.4.1.2011.2.25.238.1.4.1.2.1.65536
Count of failed full initializations on the line since agent reset.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

adsl2PMLInitEverBeforeShortInits		1.3.6.1.4.1.2011.2.25.238.1.4.1.2.1.65537
Count of short initializations attempted on the line (successful and failed) since agent reset.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

adsl2PMLInitEverBeforeFailedShortInits		1.3.6.1.4.1.2011.2.25.238.1.4.1.2.1.65538
Count of failed short initializations on the line since agent reset.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

adsl2PMChEverBeforeCodingViolations		1.3.6.1.4.1.2011.2.25.238.1.4.2.1.1.65535
Count of CRC-8 (FEBE for ATU-R) anomalies occurring in the channel since agent reset. This parameter is inhibited during UAS or SES. If the CRC is applied over multiple channels, then each related CRC-8 (or FEBE) anomaly should increment each of the counters related to the individual channels.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

adsl2PMChEverBeforeCorrectedBlocks		1.3.6.1.4.1.2011.2.25.238.1.4.2.1.1.65536
Count of FEC (FFEC for ATU-R) anomalies (corrected code words) occurring in the channel since agent reset. This parameter is inhibited during UAS or SES. If the FEC is applied over multiple channels, then each related FEC (or FFEC) anomaly should increment each of the counters related to the individual channels.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwadslmodecfg		1.3.6.1.4.1.2011.2.25.238.1.65535.1
This object is used to change ADSL management mode. After the mode being changed, system will automatically save data and reboot. Options: 1. rfc2662(1) - Management model based on RFC2662 and RFC3440 2. rfc4706(2) - Management model based on RFC4706 3. tr165(3) - Management model based on TR-165
Status: current	Access: read-write
OBJECT-TYPE
	Adsl2CfgMode

hwadslabrmodecfg		1.3.6.1.4.1.2011.2.25.238.1.65535.2
This object is used to change abr-calculation mode. Options: 1. normalMode(1) - Change mode to normal abr-calculation 2. ptMode(2) - Change mode to pt abr-calculation
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	normalMode(1), ptMode(2)

adsl2LConfProfTrellisMode		1.3.6.1.4.1.2011.2.25.238.1.5.1.2.1.65535
Enable and disable the trellis mode. This object is defaulted enabled(2). Options: 1. disable(1) - Disable the trellis 2. enable(2) - Enable the trellis
Status: current	Access: read-create
OBJECT-TYPE
	Adsl2TrellisMode

adsl2LConfProfBitSwapDs		1.3.6.1.4.1.2011.2.25.238.1.5.1.2.1.65536
Enable and disable the bit swap downstream of a line. This object is defaulted enable(2). Options: 1. disable(1) - Disable the bit swap downstream of a line 2. enable(2) - Enable the bit swap downstream of a line
Status: current	Access: read-create
OBJECT-TYPE
	Adsl2BitSwap

adsl2LConfProfBitSwapUs		1.3.6.1.4.1.2011.2.25.238.1.5.1.2.1.65537
Enable and disable the bit swap upstream of a line. This object is defaulted enable(2). Options: 1. disable(1) - Disable the bit swap upstream of a line 2. enable(2) - Enable the bit swap upstream of a line
Status: current	Access: read-create
OBJECT-TYPE
	Adsl2BitSwap

adsl2LConfProfDpboEPsd		1.3.6.1.4.1.2011.2.25.238.1.5.1.2.1.65538
This parameter defines the PSD mask that is assumed to be permitted at the exchange. This parameter shall use the same format as PSDMASKds.The maximum number of breakpoints for DPBOEPSD is 16. This is a string of 16 pairs of values in the following structure: Octets 0+1 - Index of 1st sub-carrier used in the context of a first breakpoint Octet 2 - The PSD reduction for the sub-carrier indicated in octets 0 and 1 Octets 3-5 - Same, for a 2nd breakpoint Octets 6-8 - Same, for a 3rd breakpoint This architecture continues until octets 45-47, which are associated with a 16th breakpoint. Each subcarrier index is an unsigned number in the range 1 and NSCds. Each PSD reduction value is in the range 0 (0dBm/Hz) to 255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are in the range 0 to 190 (0 to -95dBm/Hz). When the number of breakpoints is less than 16, all remaining octets are set to the value 0xff. Unit: 0.5dBm/Hz
Status: current	Access: read-create
OBJECT-TYPE
	Adsl2DpboEpsd

adsl2LConfProfDpboEsEL		1.3.6.1.4.1.2011.2.25.238.1.5.1.2.1.65539
This configuration parameter defines the assumed electrical length of cables (E-side cables) connecting exchange based DSL services to a remote flexibility point (cabinet), that hosts the xTU-C that is subject to spectrally shaped downstream power back-off depending on this length. For this parameter the electrical length is defined as the loss (in dB) of an equivalent length of hypothetical cable at a reference frequency defined by the network operator or in spectrum management regulations. DPBOESEL shall be coded as an unsigned integer representing an electrical length from 0 dB (coded as 0) to 255.5 dB (coded as 511) in steps of 0.5 dB. All values in the range are valid.If DPBOESEL is set to zero, the DPBO in this section shall be disabled. This object is defaulted 0. Unit: 0.5dB
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..511

adsl2LConfProfDpboEsCableModelA		1.3.6.1.4.1.2011.2.25.238.1.5.1.2.1.65540
This configuration parameter defines a cable model in terms of three scalars DPBOESCMA, DPBOESCMB and DPBOESCMC that shall be used to describe the frequency dependent loss of E-side cables.Parameters DPBOESCMA, DPBOESCMB, DPBOESCMC shall be coded as unsigned integers representing a scalar value from -1 (coded as 0) to 1.5 (coded as 640) in step of 1/256. All values in the range are valid. This object is defaulted 256.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..640

adsl2LConfProfDpboEsCableModelB		1.3.6.1.4.1.2011.2.25.238.1.5.1.2.1.65541
This configuration parameter defines a cable model in terms of three scalars DPBOESCMA, DPBOESCMB and DPBOESCMC that shall be used to describe the frequency dependent loss of E-side cables.Parameters DPBOESCMA, DPBOESCMB, DPBOESCMC shall be coded as unsigned integers representing a scalar value from -1 (coded as 0) to 1.5 (coded as 640) in step of 1/256. All values in the range are valid.This object is defaulted 512.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..640

adsl2LConfProfDpboEsCableModelC		1.3.6.1.4.1.2011.2.25.238.1.5.1.2.1.65542
This configuration parameter defines a cable model in terms of three scalars DPBOESCMA, DPBOESCMB and DPBOESCMC that shall be used to describe the frequency dependent loss of E-side cables.Parameters DPBOESCMA, DPBOESCMB, DPBOESCMC shall be coded as unsigned integers representing a scalar value from -1 (coded as 0) to 1.5 (coded as 640) in step of 1/256. All values in the range are valid.This object is defaulted 256.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..640

adsl2LConfProfDpboMus		1.3.6.1.4.1.2011.2.25.238.1.5.1.2.1.65543
DPBOMUS defines the assumed Minimum Usable receive Signal PSD (in dBm/Hz) for exchange based services, used to modify parameter DPBOFMAX defined below. It shall be coded as an unsigned integer representing a PSD level from 0 dBm/Hz (coded as 0) to -127.5 dBm/Hz (coded as 255) in steps of 0.5 dBm/Hz. All values in the range are valid.This object is defaulted 180. Unit: 0.5dBm/Hz
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..255

adsl2LConfProfDpboFMin		1.3.6.1.4.1.2011.2.25.238.1.5.1.2.1.65544
DPBOFMIN defines the minimum frequency from which the DPBO shall be applied. It shall be coded as a 16 bits unsigned integer representing a frequency in multiple of 4.3125 KHz. The range of valid values is from 0 kHz (coded as 0) to 8832 kHz (coded as 2048). This object is defaulted 0. Unit: 4.3125 KHz
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..2048

adsl2LConfProfDpboFMax		1.3.6.1.4.1.2011.2.25.238.1.5.1.2.1.65545
DPBOFMAX defines the maximum frequency at which DPBO may be applied. It shall be coded as a 16 bits unsigned integer representing a frequency in multiple of 4.3125 KHz. The range of valid values is from 138 kHz (coded as 32) to 29997.75 kHz (coded as 6956). This object is defaulted 511. Unit: 4.3125 KHz
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	32..6956

adsl2SCStatusTxPSD		1.3.6.1.4.1.2011.2.25.238.1.2.2.1.65535
The PSD MASK per sub-carrier.An array of 512 16-bits values, designed for supporting up to 512 (downstream) sub-carriers. It ranges from -1400 to -300 units of 0.1 dBm/Hz (physical values are -140 to -30 dBm/Hz) Unit: 0.1 dBm/Hz
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..1024)

adsl2SCStatusSnrMargins		1.3.6.1.4.1.2011.2.25.238.1.2.2.1.65536
SNR Margin is the maximum increase in dB of the noise power received at the ATU (ATU-R on downstream direction and ATU-C on upstream direction), such that the BER requirements are met for all bearer channels received at the ATU. It ranges from -640 to 630 units of 0.1 dB (physical values are -64 to 63 dB). Unit: 0.1 dB
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..1024)

adsl2LineStatusCodingGainDs		1.3.6.1.4.1.2011.2.25.238.1.1.1.1.65535
The actual value of Coding gain upstream parameter,it ranges from 0 to 16. Unit: 0.5 dB
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

adsl2LineStatusCodingGainUs		1.3.6.1.4.1.2011.2.25.238.1.1.1.1.65536
The actual value of Coding gain downstream parameter,it ranges from 0 to 16. Unit: 0.5 dB
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

adsl2LineStatusPcbDs		1.3.6.1.4.1.2011.2.25.238.1.1.1.1.65537
Indicates Power Cut-back on downstream direction. It ranges from 0 to 400 units of 0.1 dB (physical values are 0 to 40 dB). Unit: tenth dB
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

adsl2LineStatusPcbUs		1.3.6.1.4.1.2011.2.25.238.1.1.1.1.65538
Indicates Power Cut-back on upstream direction. It ranges from 0 to 400 units of 0.1 dB (physical values are 0 to 40 dB) Unit: tenth dB
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwadsl2Dynamicprofile		1.3.6.1.4.1.2011.2.25.238.1.1.1.1.65539
The value of this object identifies the row in the ADSL Dynamic Profile Table,which applies to this ADSL line, and channels if applicable. NULL - indicates that there is no Dynamic profile bound to this port.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..32)

hwadsl2		1.3.6.1.4.1.2011.6.138.1
OBJECT IDENTIFIER

hwadsl2Line		1.3.6.1.4.1.2011.6.138.1.1
OBJECT IDENTIFIER

hwadsl2Status		1.3.6.1.4.1.2011.6.138.1.2
OBJECT IDENTIFIER

hwadsl2Inventory		1.3.6.1.4.1.2011.6.138.1.3
OBJECT IDENTIFIER

hwadsl2PM		1.3.6.1.4.1.2011.6.138.1.4
OBJECT IDENTIFIER

hwadsl2Profile		1.3.6.1.4.1.2011.6.138.1.5
OBJECT IDENTIFIER

hwadsl2Scalar		1.3.6.1.4.1.2011.6.138.1.6
OBJECT IDENTIFIER

hwadsl2Notifications		1.3.6.1.4.1.2011.6.138.1.0
OBJECT IDENTIFIER

hwadsl2Conformance		1.3.6.1.4.1.2011.6.138.1.8
OBJECT IDENTIFIER

hwadsl2Mode		1.3.6.1.4.1.2011.6.138.1.9
OBJECT IDENTIFIER

hwAdsl2TrapsVbOids		1.3.6.1.4.1.2011.6.138.1.10
OBJECT IDENTIFIER

hwadsl2Traps		1.3.6.1.4.1.2011.6.138.1.11
OBJECT IDENTIFIER

hwadsl2PMLine		1.3.6.1.4.1.2011.6.138.1.4.1
OBJECT IDENTIFIER

hwadsl2PMChannel		1.3.6.1.4.1.2011.6.138.1.4.2
OBJECT IDENTIFIER

hwadsl2ProfileLine		1.3.6.1.4.1.2011.6.138.1.5.1
OBJECT IDENTIFIER

hwadsl2ProfileChannel		1.3.6.1.4.1.2011.6.138.1.5.2
OBJECT IDENTIFIER

hwadsl2ProfileAlarmConf		1.3.6.1.4.1.2011.6.138.1.5.3
OBJECT IDENTIFIER

hwadsl2ScalarSC		1.3.6.1.4.1.2011.6.138.1.6.1
OBJECT IDENTIFIER

hwAdsl2CommonTraps		1.3.6.1.4.1.2011.6.138.1.11.1
OBJECT IDENTIFIER

hwAdsl2CommonTrapsPrefix		1.3.6.1.4.1.2011.6.138.1.11.1.0
OBJECT IDENTIFIER

hwadsl2AlarmTraps		1.3.6.1.4.1.2011.6.138.1.11.2
OBJECT IDENTIFIER

hwadsl2AlarmTrapsPrefix		1.3.6.1.4.1.2011.6.138.1.11.2.0
OBJECT IDENTIFIER

hwadsl2ChannelStatusTable		1.3.6.1.4.1.2011.6.138.1.2.1
The table hwadsl2ChannelStatusTable contains status parameters of the ADSL2 channel and live data from equipment. The indexes of this table are ifIndex and adsl2ChStatusUnit.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hwadsl2ChannelStatusEntry

hwadsl2ChannelStatusEntry		1.3.6.1.4.1.2011.6.138.1.2.1.1
The table hwadsl2ChannelStatusTable contains status parameters of the ADSL2 channel and live data from equipment. The indexes of this entry are ifIndex and adsl2ChStatusUnit.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hwadsl2ChannelStatusEntry

hwadsl2ChStatusPhyRrrcBits		1.3.6.1.4.1.2011.6.138.1.2.1.1.1
The bits in the channel that used to retransmission. Unit: bit
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2ChStatusPhyRtxQueue		1.3.6.1.4.1.2011.6.138.1.2.1.1.2
The number of the units for retransmission.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2ChStatusINP		1.3.6.1.4.1.2011.6.138.1.2.1.1.3
If retransmission is not used in a given transmit direction, this parameter reports the actual impulse noise protection (INP) on the bearer channel in the L0 state. In the L1 or L2 state, the parameter contains the INP in the previous L0 state. If retransmission is used in a given transmit direction, this parameter reports the actual impulse noise protection (INP) against SHINE on the bearer channel in the L0 state. In the L2 state, the parameter contains the INP in the previous L0 state. Unit: 0.1 DMT symbol
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..254

hwadsl2ChStatusRSRedundancy		1.3.6.1.4.1.2011.6.138.1.2.1.1.4
The actual number of Reed-Solomon redundancy bytes per codeword used in the latency path in which the bearer channel is transported. The value is coded in bytes. The value 0 indicates no Reed-Solomon coding. Unit: byte
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..16

hwadsl2ChStatusRSSymbols		1.3.6.1.4.1.2011.6.138.1.2.1.1.5
The DMT Symbol number per codeword used in the latency path in which the bearer channel is transported. Unit: 0.01 DMT symbol
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwadsl2ChStatusInterDepth		1.3.6.1.4.1.2011.6.138.1.2.1.1.6
The actual Reed-Solomon codeword size used in the latency path in which the bearer channel is transported. The value ranges from 1 to 4096 by step of 1. The value 1 indicates no interleaving.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	1..4096

hwadsl2ChStatusSymbolLength		1.3.6.1.4.1.2011.6.138.1.2.1.1.7
The actual number of bits per symbol assigned to the latency path in which the bearer channel is transported. This value does not include trellis overhead. Unit: bit
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..65535

hwadsl2ChStatusRSSize		1.3.6.1.4.1.2011.6.138.1.2.1.1.8
The actual Reed-Solomon codeword size used in the latency path in which the bearer channel is transported. Unit: byte
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..255

hwadsl2ChStatusActNetDataRate		1.3.6.1.4.1.2011.6.138.1.2.1.1.9
In L0 state, this parameter reports the Net Data Rate at which the bearer channel is operating. In L2 state, this parameter contains the Net Data Rate in the previous L0 state. This parameter is optional if G.998.4 retransmission function is not supported. The data rate is coded in steps of 1000 bit/s.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwadsl2ChStatusActINPAgainstREIN		1.3.6.1.4.1.2011.6.138.1.2.1.1.10
If retransmission is used in a given transmit direction, this parameter reports the actual impulse noise protection (INP) against REIN (under specific conditions detailed in G.998.4) on the bearer channel in the L0 state. In the L2 state, the parameter contains the INP in the previous L0 state. The value is coded in fractions of DMT symbols with a granularity of 0.1 symbols.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwadsl2LineConfProfTable		1.3.6.1.4.1.2011.6.138.1.5.1.2
The table hwadsl2LineConfProfTable contains huawei private ADSL2 line profile configuration.Entries in this table MUST be maintained in a persistent manner. The index of this table is adsl2LConfProfProfileName.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hwadsl2LineConfProfEntry

hwadsl2LineConfProfEntry		1.3.6.1.4.1.2011.6.138.1.5.1.2.1
The table hwadsl2LineConfProfTable contains huawei private ADSL2 line profile configuration.Entries in this table MUST be maintained in a persistent manner. The index of this entry is adsl2LConfProfProfileName.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hwadsl2LineConfProfEntry

hwadsl2LConfProfInmIatoDs		1.3.6.1.4.1.2011.6.138.1.5.1.2.1.1
The parameter of downstream impulse noise monitoring inter arrival time offset. This is the Inter Arrival Time Offset that the xTU receiver shall use to determine in which bin of the Inter Arrival Time histogram the IAT is reported. The valid values for INMIATO ranges from 3 to 511 DMT symbols in steps of 1 DMT symbol.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	3..511

hwadsl2LConfProfInmIatsDs		1.3.6.1.4.1.2011.6.138.1.5.1.2.1.2
The parameter of downstream impulse noise monitoring inter arrival time step. This is the Inter Arrival Time Step that the xTU receiver shall use to determine in which bin of the Inter Arrival Time histogram the IAT is reported. The valid values for INMIATS ranges from 0 to 7 in steps of 1.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..7

hwadsl2LConfProfInmCcDs		1.3.6.1.4.1.2011.6.138.1.5.1.2.1.3
The parameter of Downstream impulse noise monitoring cluster continuation value. This is the Cluster Continuation value that the xTU receiver shall use in the cluster indication process described in the relevant ITU-T Recommendation. The valid values for INMCC range from 0 to 64 DMT symbols in steps of 1 DMT symbol.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..64

hwadsl2LConfProfInmInpeqModeDs		1.3.6.1.4.1.2011.6.138.1.5.1.2.1.4
The parameter of Downstream impulse noise monitoring equivalent impulse noise protect mode. This is the INM Equivalent INP Mode that the xTU receiver shall use in the computation of the Equivalent INP, as defined in the relevant ITU-T Recommendation. The valid values for INM_INPEQ_MODE are 0, 1, 2, 3, and 4.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..4

hwadsl2LConfProfRfiBands		1.3.6.1.4.1.2011.6.138.1.5.1.2.1.5
The RFI notch parameter. It is a string consist of begin tone index, end tone index and psd value. This is a string of 4 groups of values in the following structure: Octets 0+1 - Index of start sub-carrier used in the context of a first group Octets 2+3 - Index of end sub-carrier used in the context of a first group Octet 4+5 - The psd value configurated in the first group Octets 6-11 - Same, for a 2nd group This architecture continues until octets 22-23, which are associated with a 4th group.It can contain as most as 4 groups.
Status: current	Access: read-create
OBJECT-TYPE
	Adsl2RfiBand

hwadsl2LConfProfReferenceClock		1.3.6.1.4.1.2011.6.138.1.5.1.2.1.6
This object configures the clock reference for the ATU-C in an ADSL Line.
Status: current	Access: read-create
OBJECT-TYPE
	Adsl2LConfProfReferenceClockType

hwadsl2LConfProfL3Time		1.3.6.1.4.1.2011.6.138.1.5.1.2.1.7
This minimum time (in seconds) between an Entry into the L3 state and the L0 or L2 state. Unit: seconds
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..65535

hwadsl2LConfProfDpboEselMin		1.3.6.1.4.1.2011.6.138.1.5.1.2.1.8
DPBOESELMIN in dB is the minimum of all main cable losses for the KVz supplied when using the SOL model (expansion of a KVz and ADSL2 provision of additional KVz areas from this KVz using cross-cables to additional KVz), including the KVz at the MSAN site. This value must be adjustable as the minimum requirement via the SNMP interface in the configuration profile for each ADSL2 port, and is set individually for each MSAN site and usage. As an option, adjustment can be done for each MSAN or line card, thus taking effect for entire port groups. It is used only for determining the MUF. Unit: 0.5dB
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..511

hwadsl2LConfProfTrellisMode		1.3.6.1.4.1.2011.6.138.1.5.1.2.1.9
Enables and disables the trellis mode. This object is defaulted enabled(2).
Status: current	Access: read-create
OBJECT-TYPE
	Adsl2TrellisMode

hwadsl2LConfProfBitSwapDs		1.3.6.1.4.1.2011.6.138.1.5.1.2.1.10
Enables and disables the bit swap downstream of a line.
Status: current	Access: read-create
OBJECT-TYPE
	Adsl2BitSwap

hwadsl2LConfProfBitSwapUs		1.3.6.1.4.1.2011.6.138.1.5.1.2.1.11
Enables and disables the bit swap upstream of a line.
Status: current	Access: read-create
OBJECT-TYPE
	Adsl2BitSwap

hwadsl2LConfProfDpboEPsd		1.3.6.1.4.1.2011.6.138.1.5.1.2.1.12
This parameter defines the PSD mask that is assumed to be permitted at the exchange. This parameter shall use the same format as PSDMASKds.The maximum number of breakpoints for DPBOEPSD is 16. This is a string of 16 pairs of values in the following structure: Octets 0+1 - Index of 1st sub-carrier used in the context of a first breakpoint. Octet 2 - The PSD reduction for the sub-carrier indicated in octets 0 and 1 Octets 3-5 - Same, for a 2nd breakpoint Octets 6-8 - Same, for a 3rd breakpoint This architecture continues until octets 45-47, which are associated with a 16th breakpoint. Each subcarrier index is an unsigned number in the range 1 and NSCds. Each PSD reduction value is in the range 0 (0dBm/Hz) to 255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are in the range 0 to 190 (0 to -95dBm/Hz). When the number of breakpoints is less than 16, all remaining octets are set to the value 0xff.
Status: current	Access: read-create
OBJECT-TYPE
	Adsl2DpboEpsd

hwadsl2LConfProfDpboEsEL		1.3.6.1.4.1.2011.6.138.1.5.1.2.1.13
This configuration parameter defines the assumed electrical length of cables (E-side cables) connecting exchange based DSL services to a remote flexibility point (cabinet), that hosts the xTU-C that is subject to spectrally shaped downstream power back-off depending on this length. For this parameter the electrical length is defined as the loss (in dB) of an equivalent length of hypothetical cable at a reference frequency defined by the network operator or in spectrum management regulations. DPBOESEL shall be coded as an unsigned integer representing an electrical length from 0 dB (coded as 0) to 255.5 dB (coded as 511) in steps of 0.5 dB. All values in the range are valid.If DPBOESEL is set to zero, the DPBO in this section shall be disabled. Unit: 0.5dB
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..511

hwadsl2LConfProfDpboEsCableModelA		1.3.6.1.4.1.2011.6.138.1.5.1.2.1.14
This configuration parameter defines a cable model in terms of three scalars DPBOESCMA, DPBOESCMB and DPBOESCMC that shall be used to describe the frequency dependent loss of E-side cables.Parameters DPBOESCMA, DPBOESCMB, DPBOESCMC shall be coded as unsigned integers representing a scalar value from -1 (coded as 0) to 1.5 (coded as 640) in step of 1/256. All values in the range are valid.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..640

hwadsl2LConfProfDpboEsCableModelB		1.3.6.1.4.1.2011.6.138.1.5.1.2.1.15
This configuration parameter defines a cable model in terms of three scalars DPBOESCMA, DPBOESCMB and DPBOESCMC that shall be used to describe the frequency dependent loss of E-side cables.Parameters DPBOESCMA, DPBOESCMB, DPBOESCMC shall be coded as unsigned integers representing a scalar value from -1 (coded as 0) to 1.5 (coded as 640) in step of 1/256. All values in the range are valid.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..640

hwadsl2LConfProfDpboEsCableModelC		1.3.6.1.4.1.2011.6.138.1.5.1.2.1.16
This configuration parameter defines a cable model in terms of three scalars DPBOESCMA, DPBOESCMB and DPBOESCMC that shall be used to describe the frequency dependent loss of E-side cables.Parameters DPBOESCMA, DPBOESCMB, DPBOESCMC shall be coded as unsigned integers representing a scalar value from -1 (coded as 0) to 1.5 (coded as 640) in step of 1/256. All values in the range are valid.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..640

hwadsl2LConfProfDpboMus		1.3.6.1.4.1.2011.6.138.1.5.1.2.1.17
DPBOMUS defines the assumed Minimum Usable receive Signal PSD (in dBm/Hz) for exchange based services, used to modify parameter DPBOFMAX defined below. It shall be coded as an unsigned integer representing a PSD level from 0 dBm/Hz (coded as 0) to -127.5 dBm/Hz (coded as 255) in steps of 0.5 dBm/Hz. All values in the range are valid. Unit: 0.5dBm/Hz
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..255

hwadsl2LConfProfDpboFMin		1.3.6.1.4.1.2011.6.138.1.5.1.2.1.18
DPBOFMIN defines the minimum frequency from which the DPBO shall be applied. It shall be coded as a 16 bits unsigned integer representing a frequency in multiple of 4.3125 KHz. The range of valid values is from 0 kHz (coded as 0) to 8832 kHz (coded as 2048). Unit: 4.3125 KHz
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..2048

hwadsl2LConfProfDpboFMax		1.3.6.1.4.1.2011.6.138.1.5.1.2.1.19
DPBOFMAX defines the maximum frequency at which DPBO may be applied. It shall be coded as a 16 bits unsigned integer representing a frequency in multiple of 4.3125 KHz. The range of valid values is from 138 kHz (coded as 32) to 29997.75 kHz (coded as 6956). Unit: 4.3125 KHz
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	32..6956

hwadsl2ChConfProfileTable		1.3.6.1.4.1.2011.6.138.1.5.2.1
The table hwadsl2ChConfProfileTable contains huawei private ADSL2 channel profile configuration. Entries in this table MUST be maintained in a persistent manner. The index of this table is adsl2ChConfProfProfileName.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hwadsl2ChConfProfileEntry

hwadsl2ChConfProfileEntry		1.3.6.1.4.1.2011.6.138.1.5.2.1.1
The table hwadsl2ChConfProfileTable contains huawei private ADSL2 channel profile configuration. Entries in this table MUST be maintained in a persistent manner. The index of this entry is adsl2ChConfProfProfileName.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hwadsl2ChConfProfileEntry

hwadsl2ChConfProfDataPathMode		1.3.6.1.4.1.2011.6.138.1.5.2.1.1.1
The channel data path mode. Options: 1. atm(1) - ATM data path 2. ptm(2) - PTM data path 3. both(3) - ATM and PTM data path Huawei defined.
Status: current	Access: read-create
OBJECT-TYPE
	Adsl2DataPathMode

hwadsl2ChConfProfErasureDecoding		1.3.6.1.4.1.2011.6.138.1.5.2.1.1.2
Enable or disable the erasure decoding of a channel. Options: 1. enable(1) - Open the erasure decoding of a channel 2. disable(2) - Close the erasure decoding of a channel
Status: current	Access: read-create
OBJECT-TYPE
	Adsl2ProfSwitchType

hwadsl2ChConfProfPhyRcontrolDs		1.3.6.1.4.1.2011.6.138.1.5.2.1.1.3
To enable or disable the retransmission function of downstream PHY-R. Options: 1. enable(1) - Enable the retransmission function of downstream PHY-R 2. disable(2) - Disable the retransmission function of downstream PHY-R
Status: current	Access: read-create
OBJECT-TYPE
	Adsl2PhyRControl

hwadsl2ChConfProfPhyRcontrolUs		1.3.6.1.4.1.2011.6.138.1.5.2.1.1.4
To enable or disable the retransmission function of upstream PHY-R. Options: 1. enable(1) - Enable the retransmission function of upstream PHY-R 2. disable(2) - Disable the retransmission function of upstream PHY-R
Status: current	Access: read-create
OBJECT-TYPE
	Adsl2PhyRControl

hwadsl2ChConfProfInpMaxDs		1.3.6.1.4.1.2011.6.138.1.5.2.1.1.5
Maximum Impulse Noise Protection on downstream direction.
Status: current	Access: read-create
OBJECT-TYPE
	Adsl2SymbolProtection

hwadsl2ChConfProfInpMaxUs		1.3.6.1.4.1.2011.6.138.1.5.2.1.1.6
Maximum Impulse Noise Protection on upstream direction.
Status: current	Access: read-create
OBJECT-TYPE
	Adsl2SymbolProtection

hwadsl2ChConfProfMinRtxRatioDs		1.3.6.1.4.1.2011.6.138.1.5.2.1.1.7
This object is used to config the minimum retransmission band width parameter downstream.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..255

hwadsl2ChConfProfMinRtxRatioUs		1.3.6.1.4.1.2011.6.138.1.5.2.1.1.8
This object is used to config the minimum retransmission band width parameter upstream.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..255

hwadsl2ChConfProfMinRSoverheadDs		1.3.6.1.4.1.2011.6.138.1.5.2.1.1.9
This object is used to config the minimum RSoverhead parameter downstream.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..128

hwadsl2ChConfProfMinRSoverheadUs		1.3.6.1.4.1.2011.6.138.1.5.2.1.1.10
This object is used to config the minimum RSoverhead parameter upstream.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..128

hwadsl2PMLineCurrTable		1.3.6.1.4.1.2011.6.138.1.4.1.1
The table hwadsl2PMLineCurrTable contains current Performance Monitoring results of ADSL2 line. The PM counters in the table are not reset even when the xtU is reinitialized. They are re-initialized only when the agent itself is reset or reinitialized. The indexes of this table are ifIndex and adsl2PMLCurrUnit.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hwadsl2PMLineCurrEntry

hwadsl2PMLineCurrEntry		1.3.6.1.4.1.2011.6.138.1.4.1.1.1
The table hwadsl2PMLineCurrTable contains current Performance Monitoring results of ADSL2 line. The PM counters in the table are not reset even when the xtU is reinitialized. They are re-initialized only when the agent itself is reset or reinitialized. The indexes of this entry are ifIndex and adsl2PMLCurrUnit.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hwadsl2PMLineCurrEntry

hwadsl2PMLCurr15MInmainpeq		1.3.6.1.4.1.2011.6.138.1.4.1.1.1.1
This parameter is a count of the INMAINPEQi anomalies occurring on the line during current 15 minutes.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..68)

hwadsl2PMLCurr15MInmame		1.3.6.1.4.1.2011.6.138.1.4.1.1.1.2
This parameter is a count of the INMAME anomalies occurring on the line during current 15 minutes.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMLCurr15MInmaiat		1.3.6.1.4.1.2011.6.138.1.4.1.1.1.3
This parameter is a count of the INMAIATi anomalies occurring on the line during current 15 minutes.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

hwadsl2PMLCurr1DayInmainpeq		1.3.6.1.4.1.2011.6.138.1.4.1.1.1.4
This parameter is a count of the INMAINPEQi anomalies occurring on the line during current 1 day.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..68)

hwadsl2PMLCurr1DayInmame		1.3.6.1.4.1.2011.6.138.1.4.1.1.1.5
This parameter is a count of the INMAME anomalies occurring on the line during current 1 day.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMLCurr1DayInmaiat		1.3.6.1.4.1.2011.6.138.1.4.1.1.1.6
This parameter is a count of the INMAIATi anomalies occurring on the line during current 1 day.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

hwadsl2PMLEverBeforeInmainpeq		1.3.6.1.4.1.2011.6.138.1.4.1.1.1.7
This parameter is a count of the INMAINPEQi anomalies occurring on the line ever before.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..68)

hwadsl2PMLEverBeforeInmame		1.3.6.1.4.1.2011.6.138.1.4.1.1.1.8
This parameter is a count of the INMAME anomalies occurring on the line ever before.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMLEverBeforeInmaiat		1.3.6.1.4.1.2011.6.138.1.4.1.1.1.9
This parameter is a count of the INMAIATi anomalies occurring on the line ever before.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

hwadsl2PMLEverBeforeFecs		1.3.6.1.4.1.2011.6.138.1.4.1.1.1.10
Count of seconds since agent reset that there was at least one FEC correction event for one or more bearer channels in this line. This parameter is inhibited during UAS or SES. Unit: seconds
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMLEverBeforeEs		1.3.6.1.4.1.2011.6.138.1.4.1.1.1.11
Count of seconds since agent reset that there was: ATU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 ATU-R: FEBE >= 1 for one or more bearer channels OR LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1. This parameter is inhibited during UAS. Unit: seconds
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMLEverBeforeSes		1.3.6.1.4.1.2011.6.138.1.4.1.1.1.12
Count of seconds since agent reset that there was: ATU-C: (CRC-8 summed over all bearer channels) >= 18 OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 ATU-R: (FEBE summed over all bearer channels) >= 18 OR LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1 This parameter is inhibited during UAS. Unit: seconds
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMLEverBeforeLoss		1.3.6.1.4.1.2011.6.138.1.4.1.1.1.13
Count of seconds since agent reset that there was LOS (or LOS-FE for ATU-R). Unit: seconds
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMLEverBeforeUas		1.3.6.1.4.1.2011.6.138.1.4.1.1.1.14
Count of seconds in Unavailability State since agent reset. Unavailability begins at the onset of 10 contiguous severely -errored seconds, and ends at the onset of 10 contiguous seconds with no severely-errored seconds. Unit: seconds
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMLCurr15MStartTime		1.3.6.1.4.1.2011.6.138.1.4.1.1.1.15
Start time of the current 15-minute performance statistics.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

hwadsl2PMLCurr1DayStartTime		1.3.6.1.4.1.2011.6.138.1.4.1.1.1.16
Start time of the current 1-day performance statistics.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

hwadsl2PMLCurr15MLofs		1.3.6.1.4.1.2011.6.138.1.4.1.1.1.17
Count of seconds in the current 15 minute interval when there was Loss of Framing. Unit: seconds
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMLCurr15MLols		1.3.6.1.4.1.2011.6.138.1.4.1.1.1.18
Count of seconds in the current 15 minute interval when there was Loss of Link. Unit: seconds
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMLCurr15MLops		1.3.6.1.4.1.2011.6.138.1.4.1.1.1.19
Count of seconds in the current 15 minute interval when there was Loss of Power. Unit: seconds
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMLCurr1DayLofs		1.3.6.1.4.1.2011.6.138.1.4.1.1.1.20
Count of the number of seconds when there was Loss of Framing during the current day. Unit: seconds
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMLCurr1DayLols		1.3.6.1.4.1.2011.6.138.1.4.1.1.1.21
Count of the number of seconds when there was Loss of Link during the current day. Unit: seconds
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMLCurr1DayLops		1.3.6.1.4.1.2011.6.138.1.4.1.1.1.22
Count of the number of seconds when there was Loss of Power during the current day. Unit: seconds
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMLEverBeforeLofs		1.3.6.1.4.1.2011.6.138.1.4.1.1.1.23
Count of the number of seconds when there was Loss of Framing since agent reset. Unit: seconds
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMLEverBeforeLols		1.3.6.1.4.1.2011.6.138.1.4.1.1.1.24
Count of the number of seconds when there was Loss of Link since agent reset. Unit: seconds
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMLEverBeforeLops		1.3.6.1.4.1.2011.6.138.1.4.1.1.1.25
Count of the number of seconds when there was Loss of Power since agent reset. Unit: seconds
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMLCurr15MLeftrs		1.3.6.1.4.1.2011.6.138.1.4.1.1.1.26
If retransmission is used in a given transmit direction, this parameter is a count of the seconds with a near-end leftr defect present observed over the 15 minutes accumulation period.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMLCurr15MEfb		1.3.6.1.4.1.2011.6.138.1.4.1.1.1.27
If retransmission is used in a given transmit direction, this parameter is a count of the number of error-free bits observed over the 15 minutes accumulation period.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMLCurr15MMinEftr		1.3.6.1.4.1.2011.6.138.1.4.1.1.1.28
If retransmission is used in a given transmit direction, this parameter reports the minimum of the EFTR(Error-free throughput rate) observed over the 15 minutes accumulation period.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMLCurr1DayLeftrs		1.3.6.1.4.1.2011.6.138.1.4.1.1.1.29
If retransmission is used in a given transmit direction, this parameter is a count of the seconds with a near-end leftr defect present observed over the 24 hours accumulation period.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMLCurr1DayEfb		1.3.6.1.4.1.2011.6.138.1.4.1.1.1.30
If retransmission is used in a given transmit direction, this parameter is a count of the number of error-free bits observed over the 24 hours accumulation period.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMLCurr1DayMinEftr		1.3.6.1.4.1.2011.6.138.1.4.1.1.1.31
If retransmission is used in a given transmit direction, this parameter reports the minimum of the EFTR(Error-free throughput rate) observed over the 24 hours accumulation period.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMLEverBeforeLeftrs		1.3.6.1.4.1.2011.6.138.1.4.1.1.1.32
If retransmission is used in a given transmit direction, this parameter is a count of the seconds with a near-end leftr defect present observed ever before.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMLEverBeforeEfb		1.3.6.1.4.1.2011.6.138.1.4.1.1.1.33
If retransmission is used in a given transmit direction, this parameter is a count of the number of error-free bits observed ever before.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMLEverBeforeMinEftr		1.3.6.1.4.1.2011.6.138.1.4.1.1.1.34
If retransmission is used in a given transmit direction, this parameter reports the minimum of the EFTR(Error-free throughput rate) observed ever before.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMLineHist15MinTable		1.3.6.1.4.1.2011.6.138.1.4.1.2
The table hwadsl2PMLineHist15MinTable contains Performance Monitoring results of ADSL2 line at last 15 minutes. The PM counters in the table are not reset even when the xtU is reinitialized. They are re-initialized only when the agent itself is reset or reinitialized. The indexes of this table are ifIndex, adsl2PMLHist15MUnit and adsl2PMLHist15MInterval.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hwadsl2PMLineHist15MinEntry

hwadsl2PMLineHist15MinEntry		1.3.6.1.4.1.2011.6.138.1.4.1.2.1
The table hwadsl2PMLineHist15MinTable contains Performance Monitoring results of ADSL2 line at last 15 minutes. The PM counters in the table are not reset even when the xtU is reinitialized. They are re-initialized only when the agent itself is reset or reinitialized. The indexes of this entry are ifIndex, adsl2PMLHist15MUnit and adsl2PMLHist15MInterval.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hwadsl2PMLineHist15MinEntry

hwadsl2PMLHist15MInmainpeq		1.3.6.1.4.1.2011.6.138.1.4.1.2.1.1
This parameter is a count of the INMAINPEQi anomalies occurring on the line at last 15 minutes.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..68)

hwadsl2PMLHist15MInmame		1.3.6.1.4.1.2011.6.138.1.4.1.2.1.2
This parameter is a count of the INMAME anomalies occurring on the line at last 15 minutes.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMLHist15MInmaiat		1.3.6.1.4.1.2011.6.138.1.4.1.2.1.3
This parameter is a count of the INMAIATi anomalies occurring on the line at last 15 minutes.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

hwadsl2PMLHist15MStartTime		1.3.6.1.4.1.2011.6.138.1.4.1.2.1.4
Start time of the historical 15-minute performance statistics.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

hwadsl2PMLHist15MLofs		1.3.6.1.4.1.2011.6.138.1.4.1.2.1.5
Count of seconds in the interval when there was Loss of Framing. Unit: seconds
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMLHist15MLols		1.3.6.1.4.1.2011.6.138.1.4.1.2.1.6
Count of seconds in the interval when there was Loss of Link. Unit: seconds
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMLHist15MLops		1.3.6.1.4.1.2011.6.138.1.4.1.2.1.7
Count of seconds in the interval when there was Loss of Power. Unit: seconds
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMLHist15MLeftrs		1.3.6.1.4.1.2011.6.138.1.4.1.2.1.8
If retransmission is used in a given transmit direction, this parameter is a count of the seconds with a near-end leftr defect present observed over the 15 minutes accumulation period.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMLHist15MEfb		1.3.6.1.4.1.2011.6.138.1.4.1.2.1.9
If retransmission is used in a given transmit direction, this parameter is a count of the number of error-free bits observed over the 15 minutes accumulation period.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMLHist15MMinEftr		1.3.6.1.4.1.2011.6.138.1.4.1.2.1.10
If retransmission is used in a given transmit direction, this parameter reports the minimum of the EFTR(Error-free throughput rate) observed over the 15 minutes accumulation period.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMLineHist1DayTable		1.3.6.1.4.1.2011.6.138.1.4.1.3
The table hwadsl2PMLineHist1DayTable contains Performance Monitoring results of ADSL2 line at last 1 day. The PM counters in the table are not reset even when the xtU is reinitialized. They are re-initialized only when the agent itself is reset or reinitialized. The indexes of this table are ifIndex, adsl2PMLHist1DUnit and adsl2PMLHist1DInterval.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hwadsl2PMLineHist1DayEntry

hwadsl2PMLineHist1DayEntry		1.3.6.1.4.1.2011.6.138.1.4.1.3.1
The table hwadsl2PMLineHist1DayTable contains Performance Monitoring results of ADSL2 line at last 1 day. The PM counters in the table are not reset even when the xtU is reinitialized. They are re-initialized only when the agent itself is reset or reinitialized. The indexes of this entry are ifIndex, adsl2PMLHist1DUnit and adsl2PMLHist1DInterval.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hwadsl2PMLineHist1DayEntry

hwadsl2PMLHist1DayInmainpeq		1.3.6.1.4.1.2011.6.138.1.4.1.3.1.1
This parameter is a count of the INMAINPEQi anomalies occurring on the line at last 1 day.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..68)

hwadsl2PMLHist1DayInmame		1.3.6.1.4.1.2011.6.138.1.4.1.3.1.2
This parameter is a count of the INMAME anomalies occurring on the line at last 1 day.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMLHist1DayInmaiat		1.3.6.1.4.1.2011.6.138.1.4.1.3.1.3
This parameter is a count of the INMAIATi anomalies occurring on the line at last 1 day.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

hwadsl2PMLHist1DayStartTime		1.3.6.1.4.1.2011.6.138.1.4.1.3.1.4
Start time of the historical 1-day performance statistics.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

hwadsl2PMLHist1DayLofs		1.3.6.1.4.1.2011.6.138.1.4.1.3.1.5
Count of seconds during this interval that there was Loss of Framing. Unit: seconds
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMLHist1DayLols		1.3.6.1.4.1.2011.6.138.1.4.1.3.1.6
Count of seconds during this interval that there was Loss of Link. Unit: seconds
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMLHist1DayLops		1.3.6.1.4.1.2011.6.138.1.4.1.3.1.7
Count of seconds during this interval that there was Loss of Power. Unit: seconds
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMLHist1DLeftrs		1.3.6.1.4.1.2011.6.138.1.4.1.3.1.8
If retransmission is used in a given transmit direction, this parameter is a count of the seconds with a near-end leftr defect present observed over the 24 hours accumulation period.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMLHist1DEfb		1.3.6.1.4.1.2011.6.138.1.4.1.3.1.9
If retransmission is used in a given transmit direction, this parameter is a count of the number of error-free bits observed over the 24 hours accumulation period.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMLHist1DMinEftr		1.3.6.1.4.1.2011.6.138.1.4.1.3.1.10
If retransmission is used in a given transmit direction, this parameter reports the minimum of the EFTR(Error-free throughput rate) observed over the 24 hours accumulation period.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMLineCurrInitTable		1.3.6.1.4.1.2011.6.138.1.4.1.4
The table hwadsl2PMLineCurrInitTable contains current initialization counters of the ADSL2 line. The PM counters in the table are not reset even when the XTU is reinitialized. They are reinitialized only when the agent itself is reset or reinitialized. The index of this table is ifIndex.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hwadsl2PMLineCurrInitEntry

hwadsl2PMLineCurrInitEntry		1.3.6.1.4.1.2011.6.138.1.4.1.4.1
The table hwadsl2PMLineCurrInitTable contains current initialization counters of the ADSL2 line. The PM counters in the table are not reset even when the XTU is reinitialized. They are reinitialized only when the agent itself is reset or reinitialized. The index of this entry is ifIndex.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hwadsl2PMLineCurrInitEntry

hwadsl2PMLInitEverBeforeFullInits		1.3.6.1.4.1.2011.6.138.1.4.1.4.1.1
Count of full initializations attempted on the line (successful and failed) since agent reset.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwadsl2PMLInitEverBeforeFailedFullInits		1.3.6.1.4.1.2011.6.138.1.4.1.4.1.2
Count of failed full initializations on the line since agent reset.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwadsl2PMLInitEverBeforeShortInits		1.3.6.1.4.1.2011.6.138.1.4.1.4.1.3
Count of short initializations attempted on the line (successful and failed) since agent reset.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwadsl2PMLInitEverBeforeFailedShortInits		1.3.6.1.4.1.2011.6.138.1.4.1.4.1.4
Count of failed short initializations on the line since agent reset.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwadsl2PMLineCurrInit15MStartTime		1.3.6.1.4.1.2011.6.138.1.4.1.4.1.5
Start time of the current init 15-minute performance statistics.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

hwadsl2PMLineCurrInit1DayStartTime		1.3.6.1.4.1.2011.6.138.1.4.1.4.1.6
Start time of the current init 1-day performance statistics.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

hwadsl2PMLineInitHist15MinTable		1.3.6.1.4.1.2011.6.138.1.4.1.5
The table hwadsl2PMLineInitHist15MinTable contains Performance Monitoring results of ADSL2 line initialize at last 15 minutes. The PM counters in the table are not reset even when the xtU is reinitialized. They are re-initialized only when the agent itself is reset or reinitialized. The indexes of this table are ifIndex and adsl2PMLHistInit15MInterval.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hwadsl2PMLineInitHist15MinEntry

hwadsl2PMLineInitHist15MinEntry		1.3.6.1.4.1.2011.6.138.1.4.1.5.1
The table hwadsl2PMLineInitHist15MinTable contains Performance Monitoring results of ADSL2 line initialize at last 15 minutes. The PM counters in the table are not reset even when the xtU is reinitialized. They are re-initialized only when the agent itself is reset or reinitialized. The indexes of this entry are ifIndex and adsl2PMLHistInit15MInterval.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hwadsl2PMLineInitHist15MinEntry

hwadsl2PMLineInitHist15MinStartTime		1.3.6.1.4.1.2011.6.138.1.4.1.5.1.1
Start time of the historical init 15-minute performance statistics.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

hwadsl2PMLineInitHist1DayTable		1.3.6.1.4.1.2011.6.138.1.4.1.6
The table hwadsl2PMLineInitHist1DayTable contains Performance Monitoring results of ADSL2 line initialize at last one day. The indexes of this table are ifIndex and adsl2PMLHistinit1DInterval.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hwadsl2PMLineInitHist1DayEntry

hwadsl2PMLineInitHist1DayEntry		1.3.6.1.4.1.2011.6.138.1.4.1.6.1
The table hwadsl2PMLineInitHist1DayTable contains Performance Monitoring results of ADSL2 line initialize at last one day. The indexes of this entry are ifIndex and adsl2PMLHistinit1DInterval.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hwadsl2PMLineInitHist1DayEntry

hwadsl2PMLineInitHist1DayStartTime		1.3.6.1.4.1.2011.6.138.1.4.1.6.1.1
Start time of the historical init 1-day performance statistics.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

hwadsl2PMChCurrTable		1.3.6.1.4.1.2011.6.138.1.4.2.1
The table hwadsl2PMChCurrTable contains some extended current Performance Monitoring results of the ADSL2 channel. The PM counters in the table are not reset even when the XTU is reinitialized. They are reinitialized only when the agent itself is reset or reinitialized. The indexes of this table are ifIndex and adsl2PMChCurrUnit.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hwadsl2PMChCurrEntry

hwadsl2PMChCurrEntry		1.3.6.1.4.1.2011.6.138.1.4.2.1.1
The table hwadsl2PMChCurrTable contains some extended current Performance Monitoring results of the ADSL2 channel. The PM counters in the table are not reset even when the XTU is reinitialized. They are reinitialized only when the agent itself is reset or reinitialized. The indexes of this entry are ifIndex and adsl2PMChCurrUnit.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hwadsl2PMChCurrEntry

hwadsl2PMChCurr15MRtxCW		1.3.6.1.4.1.2011.6.138.1.4.2.1.1.1
Count of units request retransmission on this channel within the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMChCurr15MRtxCorrectedCW		1.3.6.1.4.1.2011.6.138.1.4.2.1.1.2
Count of units corrected by retransmission on this channel within the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMChCurr15MRtxUncorrectedCW		1.3.6.1.4.1.2011.6.138.1.4.2.1.1.3
Count of units uncorrected by retransmission on this channel within the current 15 minute interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMChCurr1DayRtxCW		1.3.6.1.4.1.2011.6.138.1.4.2.1.1.4
Count of units request retransmission on this channel during the current day.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMChCurr1DayRtxCorrectedCW		1.3.6.1.4.1.2011.6.138.1.4.2.1.1.5
Count of units corrected by retransmission on this channel during the current day.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMChCurr1DayRtxUncorrectedCW		1.3.6.1.4.1.2011.6.138.1.4.2.1.1.6
Count of units uncorrected by retransmission on this channel during the current day.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMChEverBeforeRtxCW		1.3.6.1.4.1.2011.6.138.1.4.2.1.1.7
Count of units request retransmission on this channel ever before.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMChEverBeforeRtxCorrectedCW		1.3.6.1.4.1.2011.6.138.1.4.2.1.1.8
Count of units corrected by retransmission on this channel ever before.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMChEverBeforeRtxUncorrectedCW		1.3.6.1.4.1.2011.6.138.1.4.2.1.1.9
Count of units uncorrected by retransmission on this channel ever before.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMChEverBeforeCodingViolations		1.3.6.1.4.1.2011.6.138.1.4.2.1.1.10
Count of CRC-8 (FEBE for ATU-R) anomalies occurring in the channel since agent reset. This parameter is inhibited during UAS or SES. If the CRC is applied over multiple channels, then each related CRC-8 (or FEBE) anomaly should increment each of the counters related to the individual channels.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwadsl2PMChEverBeforeCorrectedBlocks		1.3.6.1.4.1.2011.6.138.1.4.2.1.1.11
Count of FEC (FFEC for ATU-R) anomalies (corrected code words) occurring in the channel since agent reset. This parameter is inhibited during UAS or SES. If the FEC is applied over multiple channels, then each related FEC (or FFEC) anomaly should increment each of the counters related to the individual channels.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwadsl2PMChCur15MStartTime		1.3.6.1.4.1.2011.6.138.1.4.2.1.1.12
Start time of the channel current 15-minute performance statistics.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

hwadsl2PMChCur1DayStartTime		1.3.6.1.4.1.2011.6.138.1.4.2.1.1.13
Start time of the channel current 1-day performance statistics.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

hwadsl2PMChHist15MinTable		1.3.6.1.4.1.2011.6.138.1.4.2.2
The table hwadsl2PMChHist15MinTable contains PM channel history for 15min intervals of the ADSL2 channel. The indexes of this table are ifIndex,adsl2PMChHist15MUnit and adsl2PMChHist15MInterval.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hwadsl2PMChHist15MinEntry

hwadsl2PMChHist15MinEntry		1.3.6.1.4.1.2011.6.138.1.4.2.2.1
The table hwadsl2PMChHist15MinTable contains PM channel history for 15min intervals of the ADSL2 channel. The indexes of this entry are ifIndex,adsl2PMChHist15MUnit and adsl2PMChHist15MInterval.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hwadsl2PMChHist15MinEntry

hwadsl2PMChHist15MRtxCW		1.3.6.1.4.1.2011.6.138.1.4.2.2.1.1
Count of units request retransmission on this channel within the last 15 minutes interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMChHist15MRtxCorrectedCW		1.3.6.1.4.1.2011.6.138.1.4.2.2.1.2
Count of units corrected by retransmission on this channel within the last 15 minutes interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMChHist15MRtxUncorrectedCW		1.3.6.1.4.1.2011.6.138.1.4.2.2.1.3
Count of units uncorrected by retransmission on this channel within the last 15 minutes interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMChHist15MStartTime		1.3.6.1.4.1.2011.6.138.1.4.2.2.1.4
Start time of the historical 15-minute performance statistics.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

hwadsl2PMChHist1DTable		1.3.6.1.4.1.2011.6.138.1.4.2.3
The table hwadsl2PMChHist1DayTable contains some extended PM channel history for 1-day intervals of ADSL2. The indexes of this table are ifIndex,adsl2PMChHist1DUnit and adsl2PMChHist1DInterval.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hwadsl2PMChHist1DEntry

hwadsl2PMChHist1DEntry		1.3.6.1.4.1.2011.6.138.1.4.2.3.1
The table hwadsl2PMChHist1DayTable contains some extended PM channel history for 1-day intervals of ADSL2. The indexes of this entry are ifIndex,adsl2PMChHist1DUnit and adsl2PMChHist1DInterval.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hwadsl2PMChHist1DEntry

hwadsl2PMChHist1DRtxCW		1.3.6.1.4.1.2011.6.138.1.4.2.3.1.1
Count of units request retransmission on this channel within the last 1 day interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMChHist1DRtxCorrectedCW		1.3.6.1.4.1.2011.6.138.1.4.2.3.1.2
Count of units corrected by retransmission on this channel within the last 1 day interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMChHist1DRtxUncorrectedCW		1.3.6.1.4.1.2011.6.138.1.4.2.3.1.3
Count of units uncorrected by retransmission on this channel within the last 1 day interval.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hwadsl2PMChHist1DStartTime		1.3.6.1.4.1.2011.6.138.1.4.2.3.1.4
Start time of the historical 1-day performance statistics.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

hwadsl2LineTable		1.3.6.1.4.1.2011.6.138.1.1.1
The table hwadsl2LineTable contains configuration, command, and status parameters of the ADSL2 line. The index of this table is an interface index where the interface has an ifType of adsl2plus(238). Several objects in this table MUST be maintained in a persistent manner.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hwadsl2LineEntry

hwadsl2LineEntry		1.3.6.1.4.1.2011.6.138.1.1.1.1
The table hwadsl2LineTable contains configuration, command, and status parameters of the ADSL2 line. The index of this entry is an interface index where the interface has an ifType of adsl2plus(238). Several objects in this table MUST be maintained in a persistent manner.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hwadsl2LineEntry

hwadsl2LineStatusCodingGainDsInfo		1.3.6.1.4.1.2011.6.138.1.1.1.1.1
The actual value of Coding gain upstream parameter,it ranges from 0 to 16 units of 0.5 dB. Unit: 0.5 dB
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwadsl2LineStatusCodingGainUsInfo		1.3.6.1.4.1.2011.6.138.1.1.1.1.2
The actual value of Coding gain downstream parameter,it ranges from 0 to 16 units of 0.5 dB. Unit: 0.5 dB
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwadsl2LineStatusPcbDsInfo		1.3.6.1.4.1.2011.6.138.1.1.1.1.3
Indicates Power Cut-back on downstream direction. It ranges from 0 to 400 units of 0.1 dB (physical values are 0 to 40 dB). Unit: tenth dB
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwadsl2LineStatusPcbUsInfo		1.3.6.1.4.1.2011.6.138.1.1.1.1.4
Indicates Power Cut-back on upstream direction. It ranges from 0 to 400 units of 0.1 dB (physical values are 0 to 40 dB) and the invalid value is 4294967295. Unit: tenth dB
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwadsl2DynamicprofileInfo		1.3.6.1.4.1.2011.6.138.1.1.1.1.5
The value of this object identifies the row in the ADSL Dynamic Profile Table,which applies to this ADSL line, and channels if applicable. NULL -Indicates that there is no Dynamic profile bound to this port.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..32)

hwadsl2LineStatusInitResult		1.3.6.1.4.1.2011.6.138.1.1.1.1.6
Indicates the result of the last full initialization performed on the line. Options: 1. noFail(0) - Successful initialization 2. configError(1) - Configuration failure 3. configNotFeasible(2) - Configuration details not supported 4. commFail(3) - Communication failure 5. noPeerXtu(4) - Peer xTU not detected 6. otherCause(5) - Other initialization failure reason 7. ginpNotSelected(6) - G.998.4 Retransmission mode was not selected while RTX_MODE = FORCED or with RTX_MODE = RTX_TESTMODE 8. invalidValue(-1) - Invalid value
Status: current	Access: read-only
OBJECT-TYPE
	Hwadsl2InitResult

hwadsl2LineStatusRtxUsedDs		1.3.6.1.4.1.2011.6.138.1.1.1.1.7
This parameter specifies whether G.998.4 retransmission is used in a given transmit direction. Options: 1. rtxInuse(1) - RTX in use 2. rtxUnusedModeForbidden(2) - RTX not in use, due to RTX_MODE = FORBIDDEN 3. rtxUnusedNotSupportedXtuc(3) - RTX not in use, due to not supported by the XTU-C 4. rtxUnusedNotSupportedXtur(4) - RTX not in use, due to not supported by the XTU-R 5. rtxUnusedNotSupportedXtucAndXtur(5) - RTX not in use, due to not supported by the XTU-C and XTU-R 6. invalidValue(-1) - Invalid value
Status: current	Access: read-only
OBJECT-TYPE
	Adsl2StatusRtxUsed

hwadsl2LineStatusLastRetrainInfo		1.3.6.1.4.1.2011.6.138.1.1.1.1.8
Indicates the last retrained information performed on the line. Options: 1. none(1) - No record is available 2. cpe-l3-trigger(2) - The terminal initiates a low power consumption L3 request 3. lom-us-trigger-dra(3) - The upstream noise margin is smaller than the minimum noise margin in rate dynamic adjustment 4. lom-ds-trigger-dra(4) - The downstream noise margin is smaller than the minimum noise margin in rate dynamic adjustment 5. cpe-never-answer-oam(5) - No OAM response is received from the CPE all the time 6. cpe-no-more-answer-oam(6) - No OAM response is received from the CPE 7. persistent-ncd-us(7) - Upstream continuous no cell delineation 8. persistent-ncd-ds(8) - Downstream continuous no cell delineation 9. persistent-lcd-us(9) - Upstream continuous loss of cell delineation 10.persistent-lcd-ds(10) - Downstream continuous loss of cell delineation 11.l2-problem-co-drop(11) - The CO is faulty during the switching from L0 to L2 12.l2-problem-cpe-drop(12) - The CPE is faulty during the switching from L0 to L2 13.bitswap-refused-us-co-drop(13) - The CO goes offline when the upstream bit swap fault occurs 10 times consecutively 14.bitswap-refused-us-cpe-drop(14) - The CPE goes offline when the downstream bit swap fault occurs 10 times consecutively 15.channel-change-us-co-drop(15) - The CO goes offline when the upstream net rate changes 16.channel-change-us-cpe-drop(16) - The CPE goes offline when the upstream net rate changes 17.noise-increase-us-co-drop(17) - The CO goes offline when the upstream noise increases 18.noise-increase-us-cpe-drop(18) - The CPE goes offline when the upstream noise increases 19.bitswap-refused-ds-co-drop(19) - The CO goes offline when the downstream bit swap fault occurs 10 times consecutively 20.bitswap-refused-ds-cpe-drop(20) - The CPE goes offline when the downstream bit swap fault occurs 10 times consecutively 21.channel-change-ds-co-drop(21) - The CO goes offline when the downstream net rate changes 22.channel-change-ds-cpe-drop(22) - The CPE goes offline when the downstream net rate changes 23.noise-increase-ds-co-drop(23) - The CO goes offline when the downstream noise increases 24.noise-increase-ds-cpe-drop(24) - The CPE goes offline when the downstream noise increases 25.lom-us-co-drop(25) - The CO goes offline when the upstream noise margin is smaller than the minimum noise margin 26.lom-us-cpe-drop(26) - The CPE goes offline when the upstream noise margin is smaller than the minimum noise margin 27.lom-ds-co-drop(27) - The CO goes offline when the downstream noise margin is smaller than the minimum noise margin 28.lom-ds-cpe-drop(28) - The CPE goes offline when the downstream noise margin is smaller than the minimum noise margin 29.sra-problem-us-co-drop(29) - The CO goes offline when the upstream SRA is faulty 30.sra-problem-us-cpe-drop(30) - The CPE goes offline when the upstream SRA is faulty 31.sra-failed-us-co-drop(31) - The CO goes offline when the upstream SRA fails 32.sra-failed-us-cpe-drop(32) - The CPE goes offline when the upstream SRA fails 33.sra-problem-ds-co-drop(33) - The CO goes offline when the downstream SRA is fault 34.sra-problem-ds-cpe-drop(34) - The CPE goes offline when the downstream SRA is faulty 35.sra-rejected-ds-co-drop(35) - The CO goes offline when the downstream SRA is rejected 36.sra-rejected-ds-cpe-drop(36) - The CPE goes offline when the downstream SRA is rejected 37.bitswap-problem-us-co-drop(37) - The CO goes offline when the upstream bit swap is faulty 38.bitswap-problem-us-cpe-drop(38) - The CPE goes offline when the upstream bit swap is faulty 39.bitswap-failed-us-co-drop(39) - The CO goes offline when the upstream bit swap fails 40.bitswap-failed-us-cpe-drop(40) - The CPE goes offline when the upstream bit swap fails 41.bitswap-problem-ds-co-drop(41) - The CO goes offline when the downstream bit swap is faulty 42.bitswap-problem-ds-cpe-drop(42) - The CPE goes offline when the downstream bit swap is faulty 43.bitswap-rejected-ds-co-drop(43) - The CO goes offline when the downstream bit swap is rejected 44.bitswap-rejected-ds-cpe-drop(44) - The CPE goes offline when the downstream bit swap is rejected 45.cpe-switched-off(45) - The CPE power supply is shut down 46.cpe-lost(46) - The CPE is disconnected 47.co-reset(47) - The CO resets the chipset or line 48.co-stop(48) - The CO actively deactivate the port 49.unknown(49) - Unknown reason
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), cpe-l3-trigger(2), lom-us-trigger-dra(3), lom-ds-trigger-dra(4), cpe-never-answer-oam(5), cpe-no-more-answer-oam(6), persistent-ncd-us(7), persistent-ncd-ds(8), persistent-lcd-us(9), persistent-lcd-ds(10), l2-problem-co-drop(11), l2-problem-cpe-drop(12), bitswap-refused-us-co-drop(13), bitswap-refused-us-cpe-drop(14), channel-change-us-co-drop(15), channel-change-us-cpe-drop(16), noise-increase-us-co-drop(17), noise-increase-us-cpe-drop(18), bitswap-refused-ds-co-drop(19), bitswap-refused-ds-cpe-drop(20), channel-change-ds-co-drop(21), channel-change-ds-cpe-drop(22), noise-increase-ds-co-drop(23), noise-increase-ds-cpe-drop(24), lom-us-co-drop(25), lom-us-cpe-drop(26), lom-ds-co-drop(27), lom-ds-cpe-drop(28), sra-problem-us-co-drop(29), sra-problem-us-cpe-drop(30), sra-failed-us-co-drop(31), sra-failed-us-cpe-drop(32), sra-problem-ds-co-drop(33), sra-problem-ds-cpe-drop(34), sra-rejected-ds-co-drop(35), sra-rejected-ds-cpe-drop(36), bitswap-problem-us-co-drop(37), bitswap-problem-us-cpe-drop(38), bitswap-failed-us-co-drop(39), bitswap-failed-us-cpe-drop(40), bitswap-problem-ds-co-drop(41), bitswap-problem-ds-cpe-drop(42), bitswap-rejected-ds-co-drop(43), bitswap-rejected-ds-cpe-drop(44), cpe-switched-off(45), cpe-lost(46), co-reset(47), co-stop(48), unknown(49)

hwadsl2LineStatusLineRateDs		1.3.6.1.4.1.2011.6.138.1.1.1.1.9
The actual line rate downstream. Unit: bits/second
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwadsl2LineStatusLineRateUs		1.3.6.1.4.1.2011.6.138.1.1.1.1.10
The actual line rate upstream. Unit: bits/second
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hwadsl2SCStatusTable		1.3.6.1.4.1.2011.6.138.1.2.2
The table hwadsl2SCStatusTable contains status parameters of the ADSL2 sub-carriers. The following points apply to this table: 1. The main purpose of this table is to hold the results of a DELT. 2. This table also holds parameters obtained at line initialization time. 3. The rows in this table are volatile; that is, they are lost if the SNMP agent is rebooted. 4. Due to the large OCTET STRING attributes in this table, the worst case memory requirements for this table are very high. The manager may use the row status attribute of this table to delete rows in order to reclaim memory. 5. The manager may create rows in this table. The SNMP agent may create rows in this table. Only the manager may delete rows in this table. 6. The maximum number of rows allowable in this table is indicated by the scalar attribute adsl2ScalarSCMaxInterfaces. The number of rows available in this table is indicated by the scalar attribute adsl2ScalarSCAvailInterfaces. 7. The SNMP agent is permitted to create rows in this table when a DELT completes successfully or when line initialization occurs. It is not mandatory for the SNMP agent to create rows in this table; hence, it may be necessary for the manager to create rows in this table before any results can be stored. 8. If the manager attempts to create a row in this table and there are no more rows available, the creation attempt will fail, and the response to the SNMP SET PDU will contain the error noCreation(11). 9. If the SNMP agent attempts to create a row in this table and there are no more rows available, the creation attempt will fail, and the attribute adsl2LineCmndConfLdsfFailReason will indicate the reason for the failure. The failure reason will be either tableFull(10) or noResources(11). 10. An example of use of this table is as follows: Step 1. : The DELT is started by setting the : adsl2LineCmndConfLdsf from inhibit to force. Step 2. : The DELT completes, and valid data is : available. Step 3. : The row in the adsl2SCStatusTable where the : results will be stored does not yet exist so : the SNMP agent attempts to create the row. Step 4. : Due to a low memory condition, a row in the : adsl2SCStatusTable table cannot be created at : this time. Step 5. : The reason for the failure, tableFull(10), is : indicated in the adsl2LineCmndConfLdsfFailReason : attribute. 11. Another example of use of this table is as follows : Step 1. : The DELT is started by setting the : adsl2LineCmndConfLdsf from inhibit to force. Step 2. : The DELT completes and valid data is : available. Step 3. : The row in the adsl2SCStatusTable where the : results will be stored does not yet exist so : the SNMP agent attempts to create the row. Step 4. : The row creation is successful. Step 5. : The value of the attribute : adsl2LineCmndConfLdsfFailReasonreason is set : to success(2). 12. Another example of use of this table is as follows: Step 1. : The manager creates a row in adsl2SCStatusTable : for a particular ADSL2 line. Step 2. : The DELT is started on the above-mentioned : line by setting the adsl2LineCmndConfLdsf from : inhibit to force. Step 3. : The DELT completes, and valid data is : available. Step 4. : The value of the attribute : adsl2LineCmndConfLdsfFailReasonreason is set : to success(2). The indexes of this table are ifIndex and adsl2SCStatusDirection.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hwadsl2SCStatusEntry

hwadsl2SCStatusEntry		1.3.6.1.4.1.2011.6.138.1.2.2.1
The table hwadsl2SCStatusTable contains status parameters of the ADSL2 sub-carriers. The following points apply to this table: 1. The main purpose of this table is to hold the results of a DELT. 2. This table also holds parameters obtained at line initialization time. 3. The rows in this table are volatile; that is, they are lost if the SNMP agent is rebooted. 4. Due to the large OCTET STRING attributes in this table, the worst case memory requirements for this table are very high. The manager may use the row status attribute of this table to delete rows in order to reclaim memory. 5. The manager may create rows in this table. The SNMP agent may create rows in this table. Only the manager may delete rows in this table. 6. The maximum number of rows allowable in this table is indicated by the scalar attribute adsl2ScalarSCMaxInterfaces. The number of rows available in this table is indicated by the scalar attribute adsl2ScalarSCAvailInterfaces. 7. The SNMP agent is permitted to create rows in this table when a DELT completes successfully or when line initialization occurs. It is not mandatory for the SNMP agent to create rows in this table; hence, it may be necessary for the manager to create rows in this table before any results can be stored. 8. If the manager attempts to create a row in this table and there are no more rows available, the creation attempt will fail, and the response to the SNMP SET PDU will contain the error noCreation(11). 9. If the SNMP agent attempts to create a row in this table and there are no more rows available, the creation attempt will fail, and the attribute adsl2LineCmndConfLdsfFailReason will indicate the reason for the failure. The failure reason will be either tableFull(10) or noResources(11). 10. An example of use of this table is as follows: Step 1. : The DELT is started by setting the : adsl2LineCmndConfLdsf from inhibit to force. Step 2. : The DELT completes, and valid data is : available. Step 3. : The row in the adsl2SCStatusTable where the : results will be stored does not yet exist so : the SNMP agent attempts to create the row. Step 4. : Due to a low memory condition, a row in the : adsl2SCStatusTable table cannot be created at : this time. Step 5. : The reason for the failure, tableFull(10), is : indicated in the adsl2LineCmndConfLdsfFailReason : attribute. 11. Another example of use of this table is as follows : Step 1. : The DELT is started by setting the : adsl2LineCmndConfLdsf from inhibit to force. Step 2. : The DELT completes and valid data is : available. Step 3. : The row in the adsl2SCStatusTable where the : results will be stored does not yet exist so : the SNMP agent attempts to create the row. Step 4. : The row creation is successful. Step 5. : The value of the attribute : adsl2LineCmndConfLdsfFailReasonreason is set : to success(2). 12. Another example of use of this table is as follows: Step 1. : The manager creates a row in adsl2SCStatusTable : for a particular ADSL2 line. Step 2. : The DELT is started on the above-mentioned : line by setting the adsl2LineCmndConfLdsf from : inhibit to force. Step 3. : The DELT completes, and valid data is : available. Step 4. : The value of the attribute : adsl2LineCmndConfLdsfFailReasonreason is set : to success(2). The indexes of this entry are ifIndex and adsl2SCStatusDirection.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hwadsl2SCStatusEntry

hwadsl2SCStatusInfoTxPSD		1.3.6.1.4.1.2011.6.138.1.2.2.1.1
The PSD MASK per sub-carrier.An array of 512 16-bits values, designed for supporting up to 512 (downstream) sub-carriers. It ranges from -1400 to -300 units of 0.1 dBm/Hz (physical values are -140 to -30 dBm/Hz). Unit: 0.1 dBm/Hz
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..1024)

hwadsl2SCStatusInfoSnrMargins		1.3.6.1.4.1.2011.6.138.1.2.2.1.2
SNR Margin is the maximum increase in dB of the noise power received at the ATU (ATU-R on downstream direction and ATU-C on upstream direction), such that the BER requirements are met for all bearer channels received at the ATU. It ranges from -640 to 630 units of 0.1 dB (physical values are -64 to 63 dB). Unit: 0.1 dB
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..1024)

hwadsl2ChAlarmConfProfileTable		1.3.6.1.4.1.2011.6.138.1.5.3.1
The table hwadsl2ChAlarmConfProfileTable contains ADSL2 channel PM thresholds profiles. Entries in this table MUST be maintained in a persistent manner. The index of this table is adsl2ChAlarmConfProfileName.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hwadsl2ChAlarmConfProfileEntry

hwadsl2ChAlarmConfProfileEntry		1.3.6.1.4.1.2011.6.138.1.5.3.1.1
The table hwadsl2ChAlarmConfProfileTable contains ADSL2 channel PM thresholds profiles. Entries in this table MUST be maintained in a persistent manner. The index of this entry is adsl2ChAlarmConfProfileName.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hwadsl2ChAlarmConfProfileEntry

hwadsl2ChAlarmConfProfileMonitoringRateDs		1.3.6.1.4.1.2011.6.138.1.5.3.1.1.1
The channel monitoring rate downstream. When the value you set is larger than the value of the rate downstream defined in the channel profile, it will not be successful. The value 0 means that no threshold is specified for the associated counter. Unit: bits/second
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..200000000

hwadsl2ChAlarmConfProfileMonitoringRateUs		1.3.6.1.4.1.2011.6.138.1.5.3.1.1.2
The channel monitoring rate upstream. When the value you set is larger than the value of the rate upstream defined in the channel profile, it will not be successful. The value 0 means that no threshold is specified for the associated counter. Unit: bits/second
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..200000000

hwadsl2LineAlarmConfProfileTable		1.3.6.1.4.1.2011.6.138.1.5.3.2
The table hwadsl2LineAlarmConfProfileTable contains ADSL2 line PM thresholds profiles. A default profile with an index of 'DEFVAL' will always exist, and its parameters will be set to vendor- specific values, unless otherwise specified in this document. The index of this table is adsl2LineAlarmConfProfileName.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hwadsl2LineAlarmConfProfileEntry

hwadsl2LineAlarmConfProfileEntry		1.3.6.1.4.1.2011.6.138.1.5.3.2.1
The table hwadsl2LineAlarmConfProfileTable contains ADSL2 line PM thresholds profiles. A default profile with an index of 'DEFVAL' will always exist, and its parameters will be set to vendor- specific values, unless otherwise specified in this document. The index of this entry is adsl2LineAlarmConfProfileName.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hwadsl2LineAlarmConfProfileEntry

hwadsl2LineAlarmConfProfileXturThresh15MinLeftrs		1.3.6.1.4.1.2011.6.138.1.5.3.2.1.1
A threshold for the hwadsl2PMLCurr15MLeftrs counter, when adsl2PMLCurrUnit is ATUR {2}. The value 0 means that no threshold is specified for the associated counter. Unit: seconds
Status: current	Access: read-create
OBJECT-TYPE
	HCPerfIntervalThreshold

hwAdsl2LineAlarmConfProfileDyingGaspAlarmSwitch		1.3.6.1.4.1.2011.6.138.1.5.3.2.1.2
This object enable/disable the report of LOSS-OF-POWER alarm in an ADSL line. Options: 1. enable(1) - The report of LOSS-OF-POWER alarm in an ADSL line is enabled 2. disable(2) - The report of LOSS-OF-POWER alarm in an ADSL line is disabled
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

hwAdsl2LineAlarmConfProfileActiveFailAlarmSwitch		1.3.6.1.4.1.2011.6.138.1.5.3.2.1.3
This object enable/disable the active fail alarm switch. Options: 1. enable(1) - The active fail alarm switch is enabled 2. disable(2) - The active fail alarm switch is disabled
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

hwadslmodecfgCfg		1.3.6.1.4.1.2011.6.138.1.9.1
This object is used to change ADSL management mode. After the mode being changed, system will automatically save data and reboot.
Status: current	Access: read-write
OBJECT-TYPE
	Adsl2CfgMode

hwadslabrmodecfgCfg		1.3.6.1.4.1.2011.6.138.1.9.2
This object is used to change abr-calculation mode. Options: 1. normalMode(1) - Normal abr-calculation mode 2. ptMode(2) - PT abr-calculation mode
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	normalMode(1), ptMode(2)

hwadsl2LinePMThresholdItem		1.3.6.1.4.1.2011.6.138.1.10.0
Indicate the threshold item.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	OCTET STRING	Size(0..1024)

hwadsl2LineTemplateID		1.3.6.1.4.1.2011.6.138.1.10.1
Indicate line template ID.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Gauge32

hwadsl2ActivationFailureCause		1.3.6.1.4.1.2011.6.138.1.10.2
The reason of activation failure.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	OCTET STRING	Size(0..1024)

hwadsl2ChipsetID		1.3.6.1.4.1.2011.6.138.1.10.3
The Chipset ID.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

hwAdsl2SwitchResult		1.3.6.1.4.1.2011.6.138.1.10.4
Mode switch result. Options: 1. success(0) - Indicates that the adsl mode switch result is success 2. fail(1) - Indicates that the adsl mode switch result is fail
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	INTEGER	success(0), fail(1)

hwAdsl2RequestID		1.3.6.1.4.1.2011.6.138.1.10.5
Request ID.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

hwadsl2LineCmndConfLdsfResult		1.3.6.1.4.1.2011.6.138.1.10.6
The result of the test. Options: 1. success(0) - Indicates that the test result is success 2. fail(1) - Indicates that the test result is fail
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	INTEGER	success(0), fail(1)

hwadsl2LinePMThresholdValue		1.3.6.1.4.1.2011.6.138.1.10.7
Indicate the threshold value of threshold item.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

hwadsl2LinePMCurrentValue		1.3.6.1.4.1.2011.6.138.1.10.8
Indicate the current value of threshold item.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

hwadsl2ChPMThresholdValue		1.3.6.1.4.1.2011.6.138.1.10.9
Indicate the threshold value of threshold item.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

hwadsl2ChPMCurrentValue		1.3.6.1.4.1.2011.6.138.1.10.10
Indicate the current value of threshold item.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

hwAdsl2ModeSwitchResultTrap		1.3.6.1.4.1.2011.6.138.1.11.1.0.1
Adsl2 mode switch result trap. This trap message is generated when the result of the recent ADSL mode switch process.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwAdsl2AdminModeTrap		1.3.6.1.4.1.2011.6.138.1.11.1.0.2
Adsl2 administration mode trap. This trap message is generated when the ADSL mode is the system worked.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwAdsl2DeltOperResultTrap		1.3.6.1.4.1.2011.6.138.1.11.1.0.3
NGADSL delt trap. This trap message is generated when delt test result reported.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwAdsl2PortStatusChangeTrap		1.3.6.1.4.1.2011.6.138.1.11.1.0.4
Adsl2 port status change trap. This trap message is generated when port status changes.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwadsl2PortAutoDeactiveAlarmTrap		1.3.6.1.4.1.2011.6.138.1.11.2.0.0
Port automatically trap. This trap message is generated when the ADSL port is automatically deactivated. The ADSL port is automatically deactivated due to the line fault.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwAdsl2PortReactiveAlarmTrap		1.3.6.1.4.1.2011.6.138.1.11.2.0.1
Port reactive trap. This trap message is generated when the ADSL port is re-activated after the ADSL line recovers.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwAdsl2PortATURPowerOffAlarmTrap		1.3.6.1.4.1.2011.6.138.1.11.2.0.2
Port ATU-R power off trap. This trap message is generated when ATU-R is powered off.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwAdsl2ChipsetRecoverAlarmTrap		1.3.6.1.4.1.2011.6.138.1.11.2.0.3
Chipset recover trap. This trap message is generated when the ADSL chipset recovers.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwAdsl2PortDeactiveAlarmTrap		1.3.6.1.4.1.2011.6.138.1.11.2.0.4
Port deactive trap. This trap message is generated when some xDSL ports or all the xDSL ports are automatically deactivated. Some xDSL ports or all the xDSL ports are automatically deactivated due to lack of licenses.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwAdsl2LinePerformanceStatAlarmTrap		1.3.6.1.4.1.2011.6.138.1.11.2.0.5
Line performance statistics trap. This trap message is generated when the line performance statistics of the ADSL port reach the threshold.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwAdsl2DownstreamActivationRateAlarmTrap		1.3.6.1.4.1.2011.6.138.1.11.2.0.6
ADSL channel downstream activation rate trap. This trap message is generated when the ADSL channel downstream activation rate is lower than the threshold.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwAdsl2ChannelPerformanceStatAlarmTrap		1.3.6.1.4.1.2011.6.138.1.11.2.0.7
Channel performance statistics trap. This trap message is generated when the channel performance statistics of the ADSL port reach the threshold.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwAdsl2UpstreamActivationRateAlarmTrap		1.3.6.1.4.1.2011.6.138.1.11.2.0.8
ADSL channel upstream activation rate trap. This trap message is generated when the ADSL channel upstream activation rate is lower than the threshold.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwAdsl2UpstreamRateIncreaseAlarmTrap		1.3.6.1.4.1.2011.6.138.1.11.2.0.9
ADSL channel upstream rate increases trap. This trap message is generated when the ADSL channel upstream rate increases to a value higher than the threshold.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwAdsl2UpstreamRateDecreaseAlarmTrap		1.3.6.1.4.1.2011.6.138.1.11.2.0.10
ADSL channel upstream rate decreases trap. This trap message is generated when the ADSL channel upstream rate decreases to a value lower than the threshold.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwAdsl2DownstreamRateIncreaseAlarmTrap		1.3.6.1.4.1.2011.6.138.1.11.2.0.11
ADSL channel downstream rate increases trap. This trap message is generated when the ADSL channel downstream rate increases to a value higher than the threshold.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwAdsl2DownstreamRateDecreaseAlarmTrap		1.3.6.1.4.1.2011.6.138.1.11.2.0.12
ADSL channel downstream rate decreases trap. This trap message is generated when the ADSL channel downstream rate decreases to a value lower than the threshold.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwAdsl2FailedActiveAlarmTrap		1.3.6.1.4.1.2011.6.138.1.11.2.0.13
Failed active trap. This trap message is generated when it failed to activate the port using the ADSL line configuration parameters.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwAdsl2ChipsetNotAvailableAlarmTrap		1.3.6.1.4.1.2011.6.138.1.11.2.0.14
Chipset not available trap. This trap message is generated when the ADSL chipset is not available.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE