HUAWEI-ETHERNET-OPTICMODULE-MIB

File: HUAWEI-ETHERNET-OPTICMODULE-MIB.mib (117149 bytes)

Imported modules

HUAWEI-DEVICE-MIB HUAWEI-MIB IF-MIB
SNMPv2-SMI SNMPv2-TC

Imported symbols

hwFrameIndex hwSlotIndex hwPortIndex
hwPortDesc huaweiMgmt ifIndex
InterfaceIndex TimeTicks OBJECT-TYPE
Integer32 Unsigned32 MODULE-IDENTITY
NOTIFICATION-TYPE TruthValue MacAddress
RowStatus TEXTUAL-CONVENTION

Defined Types

PortList  
Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.
TEXTUAL-CONVENTION    
  OCTET STRING  

HwOpticsModuleInformationEntry  
SEQUENCE    
  hwOpticsMDIdentifier INTEGER
  hwOpticsMDExtID INTEGER
  hwOpticsMDConnector INTEGER
  hwOpticsMDEncoding INTEGER
  hwOpticsMDBrNominal Integer32
  hwOpticsMDLength9Micronkm Integer32
  hwOpticsMDLength9Micron Integer32
  hwOpticsMDLength50Micron Integer32
  hwOpticsMDLength62Micron5 Integer32
  hwOpticsMDLengthCopper Integer32
  hwOpticsMDVendorName OCTET STRING
  hwOpticsMDVendorOUI Integer32
  hwOpticsMDVendorPN OCTET STRING
  hwOpticsMDVendorRev OCTET STRING
  hwOpticsMDWaveLength Integer32
  hwOpticsMDCcBase Integer32
  hwOpticsMDOptions INTEGER
  hwOpticsMDBrMax Integer32
  hwOpticsMDBrMin Integer32
  hwOpticsMDVendorSN OCTET STRING
  hwOpticsMDDateCode OCTET STRING
  hwOpticsMDDiagnosticMonitoringType INTEGER
  hwOpticsMDEnhancedOptions INTEGER
  hwOpticsMDSFF8472Compliance INTEGER
  hwOpticsMDCcExt Integer32
  hwOpticsMDVendorSpecific OCTET STRING
  hwOpticsMDCLEICode OCTET STRING
  hwOpticsMDInfoRemote INTEGER

HwOpticsModuleTransceiverEntry  
SEQUENCE    
  hwOpticsMDInfinibandComplianceCodes INTEGER
  hwOpticsMDSONETcomplianceCodes INTEGER
  hwOpticsMDGEComplianceCodes INTEGER
  hwOpticsMDLinkLength INTEGER
  hwOpticsMDTransmitterTechnology INTEGER
  hwOpticsMDTransmissionMedia INTEGER
  hwOpticsMDSpeed INTEGER
  hwOpticsMDTransceiverRemote INTEGER

Hw10GEOpticsModuleInformationEntry  
SEQUENCE    
  hw10GEOpticsMDIdentifier INTEGER
  hw10GEOpticsMDExtCLEICode INTEGER
  hw10GEOpticsMDExtTXRefClock INTEGER
  hw10GEOpticsMDExtCDRFunc INTEGER
  hw10GEOpticsMDExtPowerLevel INTEGER
  hw10GEOpticsMDConnector INTEGER
  hw10GEOpticsMDEthComplianceBaseEW INTEGER
  hw10GEOpticsMDEthComplianceBaseLW INTEGER
  hw10GEOpticsMDEthComplianceBaseSW INTEGER
  hw10GEOpticsMDEthComplianceBaseLRM INTEGER
  hw10GEOpticsMDEthComplianceBaseER INTEGER
  hw10GEOpticsMDEthComplianceBaseLR INTEGER
  hw10GEOpticsMDEthComplianceBaseSR INTEGER
  hw10GEOpticsMDFibreCompliance INTEGER
  hw10GEOpticsMDLowerSpeedLink INTEGER
  hw10GEOpticsMDSONETSDHCodesI64point5 INTEGER
  hw10GEOpticsMDSONETSDHCodesI64point3 INTEGER
  hw10GEOpticsMDSONETSDHCodesI64point2 INTEGER
  hw10GEOpticsMDSONETSDHCodesI64point2r INTEGER
  hw10GEOpticsMDSONETSDHCodesI64point1 INTEGER
  hw10GEOpticsMDSONETSDHCodesI64point1r INTEGER
  hw10GEOpticsMDSONETSDHCodesS64point5b INTEGER
  hw10GEOpticsMDSONETSDHCodesS64point5a INTEGER
  hw10GEOpticsMDSONETSDHCodesS64point3b INTEGER
  hw10GEOpticsMDSONETSDHCodesS64point3a INTEGER
  hw10GEOpticsMDSONETSDHCodesS64point2b INTEGER
  hw10GEOpticsMDSONETSDHCodesS64point2a INTEGER
  hw10GEOpticsMDSONETSDHCodesS64point1 INTEGER
  hw10GEOpticsMDSONETSDHCodesG959P1L1 INTEGER
  hw10GEOpticsMDSONETSDHCodesL64point3 INTEGER
  hw10GEOpticsMDSONETSDHCodesL64point2c INTEGER
  hw10GEOpticsMDSONETSDHCodesL64point2b INTEGER
  hw10GEOpticsMDSONETSDHCodesL64point2a INTEGER
  hw10GEOpticsMDSONETSDHCodesL64point1 INTEGER
  hw10GEOpticsMDSONETSDHCodesV64point3 INTEGER
  hw10GEOpticsMDSONETSDHCodesV64point2b INTEGER
  hw10GEOpticsMDSONETSDHCodesV64point2a INTEGER
  hw10GEOpticsMDEncodingRZ INTEGER
  hw10GEOpticsMDEncodingNRZ INTEGER
  hw10GEOpticsMDEncodingSONET INTEGER
  hw10GEOpticsMDEncoding8B10B INTEGER
  hw10GEOpticsMDEncoding64B INTEGER
  hw10GEOpticsMDBrMin Integer32
  hw10GEOpticsMDBrMax Integer32
  hw10GEOpticsMDSupportLenSMF Integer32
  hw10GEOpticsMDSupportLenE50um Integer32
  hw10GEOpticsMDSupportLen50um Integer32
  hw10GEOpticsMDSupportLen62p5um Integer32
  hw10GEOpticsMDSupportLenCopper Integer32
  hw10GEOpticsMDTransmitterSupport INTEGER
  hw10GEOpticsMDDetector INTEGER
  hw10GEOpticsMDCooledTransmitterDevice INTEGER
  hw10GEOpticsMDWavelengthControl INTEGER
  hw10GEOpticsMDTransmitterTechnologySupport INTEGER
  hw10GEOpticsMDVendorName OCTET STRING
  hw10GEOpticsMDSupportXFIMode INTEGER
  hw10GEOpticsMDSupportLinesideMode INTEGER
  hw10GEOpticsMDMaxBitRateSupportedByCDR INTEGER
  hw10GEOpticsMDVendorOUI Integer32
  hw10GEOpticsMDVendorPN OCTET STRING
  hw10GEOpticsMDVendorRev OCTET STRING
  hw10GEOpticsMDWavelength Integer32
  hw10GEOpticsMDWaveTolerance Integer32
  hw10GEOpticsMDMaxCaseTemperature Integer32
  hw10GEOpticsMDMaxDissipation Integer32
  hw10GEOpticsMDCcbase Integer32
  hw10GEOpticsMDMaxDissipationPowerDownMode Integer32
  hw10GEOpticsMDMaximum5P0VSupply Integer32
  hw10GEOpticsMDMaximum3P3VSupply Integer32
  hw10GEOpticsMDMaximum1P8VSupply Integer32
  hw10GEOpticsMDMaximum5P2VSupply Integer32
  hw10GEOpticsMDVendorSN OCTET STRING
  hw10GEOpticsMDDateCode OCTET STRING
  hw10GEOpticsMDDiagnoMonitorPowerMeasure INTEGER
  hw10GEOpticsMDDiagnoMonitorTypeFECBER INTEGER
  hw10GEOpticsMDEnhancedOptions INTEGER
  hw10GEOpticsMDAuxInputOne INTEGER
  hw10GEOpticsMDAuxInputTwo INTEGER
  hw10GEOpticsMDCCEXT Integer32
  hw10GEOpticsMDVendorSpecific OCTET STRING

HwOpticsDdmInformationEntry  
SEQUENCE    
  hwOpticsTemperature Integer32
  hwOpticsSupplyVoltage Integer32
  hwOpticsTxBiasCurrent Integer32
  hwOpticsTxPower Integer32
  hwOpticsRxPower Integer32
  hwOpticsMDDdmInfoRemote INTEGER

HwOpticsPowerThresholdEntry  
SEQUENCE    
  hwOpticsPowerThresholdValue Integer32
  hwOpticsPowerThresholdSwitch INTEGER
  hwOpticsPowerTxUpperThresholdValue Integer32
  hwOpticsPowerRxUpperThresholdValue Integer32
  hwOpticsPowerRxLowerThresholdValue Integer32
  hwOpticsTemperatureLowerThresholdValue Integer32
  hwOpticsTemperatureUpperThresholdValue Integer32
  hwOpticsTemperatureThresholdSwitch INTEGER
  hwOpticsVoltageLowerThresholdValue Integer32
  hwOpticsVoltageUpperThresholdValue Integer32
  hwOpticsVoltageThresholdSwitch INTEGER
  hwOpticsCurrentLowerThresholdValue Integer32
  hwOpticsCurrentUpperThresholdValue Integer32
  hwOpticsCurrentThresholdSwitch INTEGER

HwOpticsSmartSFPExtModuleInformationEntry  
SEQUENCE    
  hwOpticsSmartSFPIdentifier INTEGER
  hwOpticsSmartSFPProtocolVersion Integer32
  hwOpticsSmartSFPSSFPEnhancedOption Integer32
  hwOpticsSmartSFPPassword Unsigned32
  hwOpticsSmartSFPRemoteControllable INTEGER
  hwOpticsSmartSFPSubCarrierControl INTEGER
  hwOpticsSmartSFPSubCarrierlinkStatus INTEGER
  hwOpticsSmartSFPLocalLoopback INTEGER
  hwOpticsSmartSFPRemoteLoopback INTEGER
  hwOpticsSmartSFPDyingGaspStatus INTEGER
  hwOpticsSmartSFPLocalRXOutputControl INTEGER
  hwOpticsSmartSFPPilottoneControl INTEGER
  hwOpticsSmartSFPPilottoneStatus INTEGER
  hwOpticsSmartSFPLoopbackdeviceloss Integer32
  hwOpticsSmartSFPRoundtripfiberloss Integer32
  hwOpticsSmartSFPExtModuleInfoRemote INTEGER

HwOpticsSmartSFPConfigEntry  
SEQUENCE    
  hwOpticsSmartSFPIILoopOpticloss Integer32

Defined Values

hwEthernet 1.3.6.1.4.1.2011.5.14
This mib is used for managing Ethernet optics module.
MODULE-IDENTITY    

hwOpticsModuleInformation 1.3.6.1.4.1.2011.5.14.6
OBJECT IDENTIFIER    

hwOpticsModuleInformationTable 1.3.6.1.4.1.2011.5.14.6.1
Indicates the optical module table of an Ethernet port. It is used for querying the information about the optical module of an Ethernet port. The index of this table is ifIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwOpticsModuleInformationEntry

hwOpticsModuleInformationEntry 1.3.6.1.4.1.2011.5.14.6.1.1
Indicates the optical module table of an Ethernet port. It is used for querying the information about the optical module of an Ethernet port. The index of this entry is ifIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwOpticsModuleInformationEntry  

hwOpticsMDIdentifier 1.3.6.1.4.1.2011.5.14.6.1.1.1
Indicate the identifier of optical module. Options: 1. unknown(1) -unknown the identifier of optical module 2. gbic(2) -the identifier of optical module is gbic 3. solderedToMotherboard(3) -the identifier of optical module is solderedToMotherboard 4. sfp(4) -the identifier of optical module is sfp 5. pin300XBI(5) -the identifier of optical module is pin300XBI 6. xenpak(6) -the identifier of optical module is xenpak 7. xfp(7) -the identifier of optical module is xfp 8. xff(8) -the identifier of optical module is xff 9. xfpe(9) -the identifier of optical module is xfpe 10. xpak(10) -the identifier of optical module is xpak 11. x2(11) -the identifier of optical module is x2
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(1), gbic(2), solderedToMotherboard(3), sfp(4), pin300XBI(5), xenpak(6), xfp(7), xff(8), xfpe(9), xpak(10), x2(11)  

hwOpticsMDExtID 1.3.6.1.4.1.2011.5.14.6.1.1.2
Indicate the extended type of optical module. Options: 1. notSpecifiedOrNotCompliant(1) -the extended type of optical module is notSpecifiedOrNotCompliant 2. moddef1(2) -the extended type of optical module is moddef1 3. moddef2(3) -the extended type of optical module is moddef2 4. moddef3(4) -the extended type of optical module is moddef3 5. bySerialIDOnly(5) -the extended type of optical module is bySerialIDOnly 6. moddef5(6) -the extended type of optical module is moddef5 7. moddef6(7) -the extended type of optical module is moddef6 8. moddef7(8) -the extended type of optical module is moddef7
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSpecifiedOrNotCompliant(1), moddef1(2), moddef2(3), moddef3(4), bySerialIDOnly(5), moddef5(6), moddef6(7), moddef7(8)  

hwOpticsMDConnector 1.3.6.1.4.1.2011.5.14.6.1.1.3
Indicate the type of optical module connector. Options: 1. unknown(1) -unknown the type of optical module connector 2. sc(2) -the type of optical module connector is sc 3. copperConnector1(3) -the type of optical module connector is copperConnector1 4. copperConnector2(4) -the type of optical module connector is copperConnector2 5. bnctnc(5) -the type of optical module connector is bnctnc 6. coaxialHeaders(6) -the type of optical module connector is coaxialHeaders 7. fiberJack(7) -the type of optical module connector is fiberJack 8. lc(8) -the type of optical module connector is lc 9. mtrj(9) -the type of optical module connector is mtrj 10. mu(10) -the type of optical module connector is mu 11. sg(11) -the type of optical module connector is sg 12. opticalPigtail(12) -the type of optical module connector is opticalPigtail 13. hssdcii(13) -the type of optical module connector is hssdcii 14. copperPigtail(14) -the type of optical module connector is copperPigtail 15. vendorSpecific(15) -the type of optical module connector is vendorSpecific
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(1), sc(2), copperConnector1(3), copperConnector2(4), bnctnc(5), coaxialHeaders(6), fiberJack(7), lc(8), mtrj(9), mu(10), sg(11), opticalPigtail(12), hssdcii(13), copperPigtail(14), vendorSpecific(15)  

hwOpticsMDEncoding 1.3.6.1.4.1.2011.5.14.6.1.1.4
Indicate the encoding mechanism. Options: 1. unspecified(1) -the encoding mechanism is unspecified 2. encodingMethod8B10B(2) -the encoding mechanism is encodingMethod8B10B 3. encodingMethod4B5B(3) -the encoding mechanism is encodingMethod4B5B 4. nrz(4) -the encoding mechanism is nrz 5. manchester(5) -the encoding mechanism is manchester 6. sONETScrambled(6) -the encoding mechanism is sONETScrambled 7. encodingMethod64B66B(7) -the encoding mechanism is encodingMethod64B66B
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unspecified(1), encodingMethod8B10B(2), encodingMethod4B5B(3), nrz(4), manchester(5), sONETScrambled(6), encodingMethod64B66B(7)  

hwOpticsMDBrNominal 1.3.6.1.4.1.2011.5.14.6.1.1.5
Nominal bit rate. Unit: 100 MBits/sec
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwOpticsMDLength9Micronkm 1.3.6.1.4.1.2011.5.14.6.1.1.6
Indicate the link length that is supported by the transceiver while operating in compliance with the applicable standards using 9 micron Single-mode Fiber. The maximum value is 255, which means that the transceiver supports a link length greater than 25.4 km. Unit: km
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwOpticsMDLength9Micron 1.3.6.1.4.1.2011.5.14.6.1.1.7
Indicate the link length that is supported by the transceiver while operating in compliance with the applicable standards using 9 micron Single-mode Fiber. The maximum value is 255, which means that the transceiver supports a link length greater than 254 km. Unit: 100m
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwOpticsMDLength50Micron 1.3.6.1.4.1.2011.5.14.6.1.1.8
Indicate link length that is supported by the transceiver while operating in compliance with applicable standards using 50 micron multi-mode OM2 [500MHz*km] fiber. The maximum value is 255, which means that the transceiver supports a link length greater than 2.54 km. Unit: 10m
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwOpticsMDLength62Micron5 1.3.6.1.4.1.2011.5.14.6.1.1.9
Indicate link length that is supported by the transceiver while operating in compliance with applicable standards using 62.5 micron multi-mode OM1 [200 MHz*km] fiber. The maximum value is 255, which means that the transceiver supports a link length greater than 2.54 km. Unit: 10m
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwOpticsMDLengthCopper 1.3.6.1.4.1.2011.5.14.6.1.1.10
Indicate Link length supported for copper. Unit: 1m
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwOpticsMDVendorName 1.3.6.1.4.1.2011.5.14.6.1.1.11
Indicate the vendor name of a optical module.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..17)  

hwOpticsMDVendorOUI 1.3.6.1.4.1.2011.5.14.6.1.1.12
Indicate the vendor IEEE company ID of a optical module.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwOpticsMDVendorPN 1.3.6.1.4.1.2011.5.14.6.1.1.13
Indicate the part number of a optical module provided by vendor.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..17)  

hwOpticsMDVendorRev 1.3.6.1.4.1.2011.5.14.6.1.1.14
Indicate the revision level for part number provided by vendor.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..5)  

hwOpticsMDWaveLength 1.3.6.1.4.1.2011.5.14.6.1.1.15
The laser wavelength.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwOpticsMDCcBase 1.3.6.1.4.1.2011.5.14.6.1.1.16
The check code for base ID fields(one byte).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwOpticsMDOptions 1.3.6.1.4.1.2011.5.14.6.1.1.17
Options: 1. rateSelect(1) -RATE-SELECT is implemented 2. txDisableAndTheSerialOutputDisabled(2) -TX-DISABLE is implemented and disables the serial output. 3. txFault(3) -TX-FAULT signal implemented. 4. signalLossAndInvertedFromStandard(4) -Loss of Signal implemented, signal inverted from standard definition in SFP MSA. 5. signalLossAndAsDefined(5) -Loss of Signal implemented, signal as defined in SFP MSA
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER rateSelect(1), txDisableAndTheSerialOutputDisabled(2), txFault(3), signalLossAndInvertedFromStandard(4), signalLossAndAsDefined(5)  

hwOpticsMDBrMax 1.3.6.1.4.1.2011.5.14.6.1.1.18
The upper bit rate margin.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwOpticsMDBrMin 1.3.6.1.4.1.2011.5.14.6.1.1.19
The lower bit rate margin.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwOpticsMDVendorSN 1.3.6.1.4.1.2011.5.14.6.1.1.20
The serial number of a optical module provided by vendor.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..17)  

hwOpticsMDDateCode 1.3.6.1.4.1.2011.5.14.6.1.1.21
The date code of a optical module.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..9)  

hwOpticsMDDiagnosticMonitoringType 1.3.6.1.4.1.2011.5.14.6.1.1.22
Indicate the diagnostic monitoring type. Options: 1. internallyCalibrated(1) -the diagnostic monitoring type is internallyCalibrated 2. externallyCalibrated(2) -the diagnostic monitoring type is externallyCalibrated 3. invalid(-1) -invalid value
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER internallyCalibrated(1), externallyCalibrated(2), invalid(-1)  

hwOpticsMDEnhancedOptions 1.3.6.1.4.1.2011.5.14.6.1.1.23
Indicate enhanced Options. Options: 1. forAllMonitoredQuantities(1) -optional Alarm/warning flags implemented for all monitored quantities 2. txDisable(2) -optional Soft TX-DISABLE control and monitoring implemented 3. txFault(3) -optional Soft TX-FAULT monitoring implemented 4. rxLOS(4) -optional Soft RX-LOS monitoring implemented 5. rateSelect(5) -optional Soft RATE-SELECT control and monitoring implemented 6. invalid(-1) -invalid value
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER forAllMonitoredQuantities(1), txDisable(2), txFault(3), rxLOS(4), rateSelect(5), invalid(-1)  

hwOpticsMDSFF8472Compliance 1.3.6.1.4.1.2011.5.14.6.1.1.24
Indicate the SFF-8472 standard. Options: 1. undefined(1) -not included or undefined. 2. includesSFF8472V93(2) -includes functionality described in Rev 9.3 SFF-8472. 3. includesSFF8472V95(3) -includes functionality described in Rev 9.5 SFF-8472. 4. includesSFF8472V102(4) -includes functionality described in Rev 10.2 SFF-8472. 5. tbd(5) -to be determined.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER undefined(1), includesSFF8472V93(2), includesSFF8472V95(3), includesSFF8472V102(4), tbd(5)  

hwOpticsMDCcExt 1.3.6.1.4.1.2011.5.14.6.1.1.25
Check code for the Extended ID Fields.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwOpticsMDVendorSpecific 1.3.6.1.4.1.2011.5.14.6.1.1.26
Vendor of Optical module specific information.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..96)  

hwOpticsMDCLEICode 1.3.6.1.4.1.2011.5.14.6.1.1.27
CLEI code supported by eSFP. Length is 10 bytes.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..10)  

hwOpticsMDInfoRemote 1.3.6.1.4.1.2011.5.14.6.1.1.28
Indicates the operation is performed on a remote optical module. Options: 1. remote(1) -the operation is performed on a remote optical module 2. invalid(-1) -invalid value
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER remote(1), invalid(-1)  

hwOpticsModuleTransceiverTable 1.3.6.1.4.1.2011.5.14.6.2
This table used for querying the information about the optical transceiver of an Ethernet port. The index of this table is ifindex.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwOpticsModuleTransceiverEntry

hwOpticsModuleTransceiverEntry 1.3.6.1.4.1.2011.5.14.6.2.1
This table used for querying the information about the optical transceiver of an Ethernet port. The index of this entry is ifindex.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwOpticsModuleTransceiverEntry  

hwOpticsMDInfinibandComplianceCodes 1.3.6.1.4.1.2011.5.14.6.2.1.1
Infiniband transceiver type. Options: 1. sx(1) -infiniband transceiver type is sx 2. lx(2) -infiniband transceiver type is lx 3. copperActive(3) -infiniband transceiver type is copperActive 4. copperPassive(4) -infiniband transceiver type is copperPassive 5. invalid(-1) -invalid value
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER sx(1), lx(2), copperActive(3), copperPassive(4), invalid(-1)  

hwOpticsMDSONETcomplianceCodes 1.3.6.1.4.1.2011.5.14.6.2.1.2
SONET transceiver type. Options: 1. oC48LongReach(1) -SONET transceiver type is oC48LongReach 2. oC48IntermediateReach(2) -SONET transceiver type is oC48IntermediateReach 3. oC48ShortReach(3) -SONET transceiver type is oC48ShortReach 4. oC12SingleModeLongReach(4) -SONET transceiver type is oC12SingleModeLongReach 5. oC12SingleModeIntermediateReach(5) -SONET transceiver type is oC12SingleModeIntermediateReach 6. oC12MultiModeShortReach(6) -SONET transceiver type is oC12MultiModeShortReach 7. oC3SingleModeLongReach(7) -SONET transceiver type is oC3SingleModeLongReach 8. oC3SingleModeIntermediateReach(8) -SONET transceiver type is oC3SingleModeIntermediateReach 9. oC3MultiModeShortReach(9) -SONET transceiver type is oC3MultiModeShortReach 10. invalid(-1) -invalid value
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER oC48LongReach(1), oC48IntermediateReach(2), oC48ShortReach(3), oC12SingleModeLongReach(4), oC12SingleModeIntermediateReach(5), oC12MultiModeShortReach(6), oC3SingleModeLongReach(7), oC3SingleModeIntermediateReach(8), oC3MultiModeShortReach(9), invalid(-1)  

hwOpticsMDGEComplianceCodes 1.3.6.1.4.1.2011.5.14.6.2.1.3
Ethernet transceiver type. Options: 1. en1000BASET(1) -Ethernet transceiver type is 1000BASE-T 2. en1000BASECX(2) -Ethernet transceiver type is 1000BASE-CX 3. en1000BASELX(3) -Ethernet transceiver type is 1000BASE-LX 4. en1000BASESX(4) -Ethernet transceiver type is 1000BASE-SX 5. enMULTILX(5) -Ethernet transceiver type is 100BASE-LX&1000BASE-LX 6. en100BASELX(6) -Ethernet transceiver type is 100BASE-LX 7. en100BASEFX(7) -Ethernet transceiver type is 100BASE-FX 8. en1000BASEBX(8) -Ethernet transceiver type is 1000BASE-BX 9. en1000BASEPX(9) -Ethernet transceiver type is 1000BASE-PX 10. en10GBASELRM(10) -Ethernet transceiver type is 10GBASE-LRM 11. en10GBASELR(11) -Ethernet transceiver type is 10GBASE-LR 12. en10GBASESR(12) -Ethernet transceiver type is 10GBASE-SR 13. en100BASEBX(13) -Ethernet transceiver type is 100BASE-BX
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER en1000BASET(1), en1000BASECX(2), en1000BASELX(3), en1000BASESX(4), enMULTILX(5), en100BASELX(6), en100BASEFX(7), en1000BASEBX(8), en1000BASEPX(9), en10GBASELRM(10), en10GBASELR(11), en10GBASESR(12), en100BASEBX(13)  

hwOpticsMDLinkLength 1.3.6.1.4.1.2011.5.14.6.2.1.4
Fibre Channel link length. Options: 1. veryLongDistance(1) -fibre channel link length is veryLongDistance 2. shortDistance(2) -fibre channel link length is shortDistance 3. intermediateDistance(3) -fibre channel link length is intermediateDistance 4. longDistance(4) -fibre channel link length is longDistance 5. invalid(-1) -invalid value
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER veryLongDistance(1), shortDistance(2), intermediateDistance(3), longDistance(4), invalid(-1)  

hwOpticsMDTransmitterTechnology 1.3.6.1.4.1.2011.5.14.6.2.1.5
Fibre Channel transmitter technology. Options: 1. longwaveLaser(1) -fibre channel transmitter technology is longwaveLaser 2. electricalInterenclosure(2) -fibre channel transmitter technology is electricalInterenclosure 3. shortwaveLaser(3) -fibre channel transmitter technology is shortwaveLaser 4. invalid(-1) -invalid value
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER longwaveLaser(1), electricalInterenclosure(2), shortwaveLaser(3), invalid(-1)  

hwOpticsMDTransmissionMedia 1.3.6.1.4.1.2011.5.14.6.2.1.6
Fibre Channel transmission media. Options: 1. twinAxialPair(1) -fibre channel transmission media is twinAxialPair 2. shieldedTwistedPair(2) -fibre channel transmission media is shieldedTwistedPair 3. miniatureCoax(3) -fibre channel transmission media is miniatureCoax 4. videoCoax(4) -fibre channel transmission media is videoCoax 5. multiMode62m5(5) -fibre channel transmission media is multiMode62m5 6. multiMode50m(6) -fibre channel transmission media is multiMode50m 7. singleMode(7) -fibre channel transmission media is singleMode 8. invalid(-1) -invalid value
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER twinAxialPair(1), shieldedTwistedPair(2), miniatureCoax(3), videoCoax(4), multiMode62m5(5), multiMode50m(6), singleMode(7), invalid(-1)  

hwOpticsMDSpeed 1.3.6.1.4.1.2011.5.14.6.2.1.7
Fibre Channel speed. Options: 1. speed400MBytesPerSec(1) -fibre channel speed is 400 MBits/s 2. speed200MBytesPerSec(2) -fibre channel speed is 200 MBits/s 3. speed100MBytesPerSec(3) -fibre channel speed is 100 MBits/s 4. invalid(-1) -invalid value
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER speed400MBytesPerSec(1), speed200MBytesPerSec(2), speed100MBytesPerSec(3), invalid(-1)  

hwOpticsMDTransceiverRemote 1.3.6.1.4.1.2011.5.14.6.2.1.8
Indicates the operation is performed on a remote optical module. Options: 1. remote(1) -the operation is performed on a remote optical module 2. invalid(-1) -invalid value
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER remote(1), invalid(-1)  

hw10GEOpticsModuleInformationTable 1.3.6.1.4.1.2011.5.14.6.3
Indicates the 10GE optical module information table of an Ethernet port. It is used for querying the information about the 10GE optical module of an Ethernet port. The index of this table is ifindex.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hw10GEOpticsModuleInformationEntry

hw10GEOpticsModuleInformationEntry 1.3.6.1.4.1.2011.5.14.6.3.1
Indicates the 10GE optical module information table of an Ethernet port. It is used for querying the information about the 10GE optical module of an Ethernet port. The index of this entry is ifindex.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hw10GEOpticsModuleInformationEntry  

hw10GEOpticsMDIdentifier 1.3.6.1.4.1.2011.5.14.6.3.1.1
Indicate the identifier of 10GE optical module. Options: 1. unknown(0) -unknown identifier of 10GE optical module 2. gbic(1) -the identifier of 10GE optical module is gbic 3. solderedToMotherBoard(2) -the identifier of 10GE optical module is solderedToMotherBoard 4. sfp(3) -the identifier of 10GE optical module is sfp 5. pin300XBI(4) -the identifier of 10GE optical module is pin300XBI 6. xenpak(5) -the identifier of 10GE optical module is xenpak 7. xfp(6) -the identifier of 10GE optical module is xfp 8. xff(7) -the identifier of 10GE optical module is xff 9. xfep(8) -the identifier of 10GE optical module is xfep 10. xpak(9) -the identifier of 10GE optical module is xpak 11. x2(10) -the identifier of 10GE optical module is x2
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(0), gbic(1), solderedToMotherBoard(2), sfp(3), pin300XBI(4), xenpak(5), xfp(6), xff(7), xfep(8), xpak(9), x2(10)  

hw10GEOpticsMDExtCLEICode 1.3.6.1.4.1.2011.5.14.6.3.1.2
Extended identifier: CLEI Options: 1. nonExtCLEICode(0) -no CLEI code present in Table 02h 2. extCLEICode(1) -CLEI code present in Table 02h
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER nonExtCLEICode(0), extCLEICode(1)  

hw10GEOpticsMDExtTXRefClock 1.3.6.1.4.1.2011.5.14.6.3.1.3
Extended identifier: TX Ref Clock Options: 1. nonExtTXRefClock(0) -tx Ref Clock Input Not Required 2. extTXRefClock(1) -tx Ref Clock Input Required
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER nonExtTXRefClock(0), extTXRefClock(1)  

hw10GEOpticsMDExtCDRFunc 1.3.6.1.4.1.2011.5.14.6.3.1.4
Extended identifier: CDR function Options: 1. nonExtCDRFunc(0) -no CDR version of XFP 2. extCDRFunc(1) -module with CDR function
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER nonExtCDRFunc(0), extCDRFunc(1)  

hw10GEOpticsMDExtPowerLevel 1.3.6.1.4.1.2011.5.14.6.3.1.5
Extended identifier: Power Level Options: 1. extPowerLevel1(0) -power Level 1 Module (1.5 W max. power dissipation.) 2. extPowerLevel2(1) -power Level 2 Module (2.5W Max) 3. extPowerLevel3(2) -power Level 3 Module (3.5W max. power dissipation.) 4. extPowerLevel4(3) -power Level 4 Module (>3.5W max. power dissipation.)
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER extPowerLevel1(0), extPowerLevel2(1), extPowerLevel3(2), extPowerLevel4(3)  

hw10GEOpticsMDConnector 1.3.6.1.4.1.2011.5.14.6.3.1.6
Indicate the type of 10GE optical module connector. Options: 1. unknown(0) -unknown the type of 10GE optical module connector 2. sc(1) -the type of 10GE optical module connector is sc 3. style1Connector(2) -the type of 10GE optical module connector is style1Connector 4. style2Connector(3) -the type of 10GE optical module connector is style2Connector 5. bnctnc(4) -the type of 10GE optical module connector is bnctnc 6. channelCoaxial(5) -the type of 10GE optical module connector is channelCoaxial 7. fiberJack(6) -the type of 10GE optical module connector is fiberJack 8. lc(7) -the type of 10GE optical module connector is lc 9. mtrj(8) -the type of 10GE optical module connector is mtrj 10. mu(9) -the type of 10GE optical module connector is mu 11. sg(10) -the type of 10GE optical module connector is sg 12. opticalPigtail(11) -the type of 10GE optical module connector is opticalPigtail 13. hssdc(20) -the type of 10GE optical module connector is hssdc 14. copperPigtail(21) -the type of 10GE optical module connector is copperPigtail
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(0), sc(1), style1Connector(2), style2Connector(3), bnctnc(4), channelCoaxial(5), fiberJack(6), lc(7), mtrj(8), mu(9), sg(10), opticalPigtail(11), hssdc(20), copperPigtail(21)  

hw10GEOpticsMDEthComplianceBaseEW 1.3.6.1.4.1.2011.5.14.6.3.1.7
Indicate 10GBASE-EW support or not. Options: 1. nonEthComplianceBaseEW(0) -not support 10GBASE-EW 2. ethComplianceBaseEW(1) -support 10GBASE-EW
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER nonEthComplianceBaseEW(0), ethComplianceBaseEW(1)  

hw10GEOpticsMDEthComplianceBaseLW 1.3.6.1.4.1.2011.5.14.6.3.1.8
Indicate 10GBASE-LW support or not. Options: 1. nonEthComplianceBaseLW(0) -not support 10GBASE-LW 2. ethComplianceBaseLW(1) -support 10GBASE-LW
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER nonEthComplianceBaseLW(0), ethComplianceBaseLW(1)  

hw10GEOpticsMDEthComplianceBaseSW 1.3.6.1.4.1.2011.5.14.6.3.1.9
Indicate 10GBASE-SW support or not. Options: 1. nonEthComplianceBaseSW(0) -not support 10GBASE-SW 2. ethComplianceBaseSW(1) -support 10GBASE-SW
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER nonEthComplianceBaseSW(0), ethComplianceBaseSW(1)  

hw10GEOpticsMDEthComplianceBaseLRM 1.3.6.1.4.1.2011.5.14.6.3.1.10
Indicate 10GBASE-LRM support or not. Options: 1. nonEthComplianceBaseLRM(0) -not support 10GBASE-LRM 2. ethComplianceBaseLRM(1) -support 10GBASE-LRM
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER nonEthComplianceBaseLRM(0), ethComplianceBaseLRM(1)  

hw10GEOpticsMDEthComplianceBaseER 1.3.6.1.4.1.2011.5.14.6.3.1.11
Indicate 10GBASE-ER support or not. Options: 1. nonEthComplianceBaseER(0) -not support 10GBASE-ER 2. ethComplianceBaseER(1) -support 10GBASE-ER
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER nonEthComplianceBaseER(0), ethComplianceBaseER(1)  

hw10GEOpticsMDEthComplianceBaseLR 1.3.6.1.4.1.2011.5.14.6.3.1.12
Indicate 10GBASE-LR support or not. Options: 1. nonEthComplianceBaseLR(0) -not support 10GBASE-LR 2. ethComplianceBaseLR(1) -support 10GBASE-LR
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER nonEthComplianceBaseLR(0), ethComplianceBaseLR(1)  

hw10GEOpticsMDEthComplianceBaseSR 1.3.6.1.4.1.2011.5.14.6.3.1.13
Indicate 10GBASE-SR support or not. Options: 1. nonEthComplianceBaseSR(0) -not support 10GBASE-SR 2. ethComplianceBaseSR(1) -support 10GBASE-SR
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER nonEthComplianceBaseSR(0), ethComplianceBaseSR(1)  

hw10GEOpticsMDFibreCompliance 1.3.6.1.4.1.2011.5.14.6.3.1.14
Indicate 10 Gigabit Fibre Channel Compliance type. Options: 1. fibreComplianceInter1300FP(16) -intermediate Reach 1300 nm FP 2. fibreComplianceExtended1550(32) -extended reach 1550 nm 3. fibreComplianceSM1200(64) -1200-SM-LL-L 4. fibreComplianceMX1200(128) -1200-MX-SN-I 5. invalid(-1) -invalid value
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER fibreComplianceInter1300FP(16), fibreComplianceExtended1550(32), fibreComplianceSM1200(64), fibreComplianceMX1200(128), invalid(-1)  


hw10GEOpticsMDSONETSDHCodesI64point5 1.3.6.1.4.1.2011.5.14.6.3.1.16
Indicate SONET/SDH Codes I-64.5 support or not. Options: 1. notSupport(0) -not Support I-64.5 2. support(1) -support I-64.5
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupport(0), support(1)  

hw10GEOpticsMDSONETSDHCodesI64point3 1.3.6.1.4.1.2011.5.14.6.3.1.17
Indicate SONET/SDH Codes I-64.3 support or not. Options: 1. notSupport(0) -not Support I-64.3 2. support(1) -support I-64.3
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupport(0), support(1)  

hw10GEOpticsMDSONETSDHCodesI64point2 1.3.6.1.4.1.2011.5.14.6.3.1.18
Indicate SONET/SDH Codes I-64.2 support or not. Options: 1. notSupport(0) -not Support I-64.2 2. support(1) -support I-64.2
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupport(0), support(1)  

hw10GEOpticsMDSONETSDHCodesI64point2r 1.3.6.1.4.1.2011.5.14.6.3.1.19
Indicate SONET/SDH Codes I-64.2r support or not. Options: 1. notSupport(0) -not support I-64.2r 2. support(1) -support I-64.2r
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupport(0), support(1)  

hw10GEOpticsMDSONETSDHCodesI64point1 1.3.6.1.4.1.2011.5.14.6.3.1.20
Indicate SONET/SDH Codes I-64.1 support or not. Options: 1. notSupport(0) -not support I-64.1 2. support(1) -support I-64.1
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupport(0), support(1)  

hw10GEOpticsMDSONETSDHCodesI64point1r 1.3.6.1.4.1.2011.5.14.6.3.1.21
Indicate SONET/SDH Codes I-64.1r support or not. Options: 1. notSupport(0) -not support I-64.1r 2. support(1) -support I-64.1r
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupport(0), support(1)  

hw10GEOpticsMDSONETSDHCodesS64point5b 1.3.6.1.4.1.2011.5.14.6.3.1.22
Indicate SONET/SDH Codes S-64.5b support or not. Options: 1. notSupport(0) -not support S-64.5b 2. support(1) -support S-64.5b
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupport(0), support(1)  

hw10GEOpticsMDSONETSDHCodesS64point5a 1.3.6.1.4.1.2011.5.14.6.3.1.23
Indicate SONET/SDH Codes S-64.5a support or not. Options: 1. notSupport(0) -not support S-64.5a 2. support(1) -support S-64.5a
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupport(0), support(1)  

hw10GEOpticsMDSONETSDHCodesS64point3b 1.3.6.1.4.1.2011.5.14.6.3.1.24
Indicate SONET/SDH Codes S-64.3b support or not. Options: 1. notSupport(0) -not support S-64.3b 2. support(1) -support S-64.3b
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupport(0), support(1)  

hw10GEOpticsMDSONETSDHCodesS64point3a 1.3.6.1.4.1.2011.5.14.6.3.1.25
Indicate SONET/SDH Codes S-64.3a support or not. Options: 1. notSupport(0) -not support S-64.3a 2. support(1) -support S-64.3a
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupport(0), support(1)  

hw10GEOpticsMDSONETSDHCodesS64point2b 1.3.6.1.4.1.2011.5.14.6.3.1.26
Indicate SONET/SDH Codes S-64.2b support or not. Options: 1. notSupport(0) -not support S-64.2b 2. support(1) -support S-64.2b
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupport(0), support(1)  

hw10GEOpticsMDSONETSDHCodesS64point2a 1.3.6.1.4.1.2011.5.14.6.3.1.27
Indicate SONET/SDH Codes S-64.2a support or not. Options: 1. notSupport(0) -not support S-64.2a 2. support(1) -support S-64.2a
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupport(0), support(1)  

hw10GEOpticsMDSONETSDHCodesS64point1 1.3.6.1.4.1.2011.5.14.6.3.1.28
Indicate SONET/SDH Codes S-64.1 support or not. Options: 1. notSupport(0) -not support S-64.1 2. support(1) -support S-64.1
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupport(0), support(1)  

hw10GEOpticsMDSONETSDHCodesG959P1L1 1.3.6.1.4.1.2011.5.14.6.3.1.29
Indicate SONET/SDH Codes G.959.1 P1L1-2D2 support or not. Options: 1. notSupport(0) -not support G.959.1 P1L1-2D2 2. support(1) -support G.959.1 P1L1-2D2
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupport(0), support(1)  

hw10GEOpticsMDSONETSDHCodesL64point3 1.3.6.1.4.1.2011.5.14.6.3.1.30
Indicate SONET/SDH Codes L-64.3 support or not. Options: 1. notSupport(0) -not support L-64.3 2. support(1) -support L-64.3
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupport(0), support(1)  

hw10GEOpticsMDSONETSDHCodesL64point2c 1.3.6.1.4.1.2011.5.14.6.3.1.31
Indicate SONET/SDH Codes L-64.2c support or not. Options: 1. notSupport(0) -not support L-64.2c 2. support(1) -support L-64.2c
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupport(0), support(1)  

hw10GEOpticsMDSONETSDHCodesL64point2b 1.3.6.1.4.1.2011.5.14.6.3.1.32
Indicate SONET/SDH Codes L-64.2b support or not. Options: 1. notSupport(0) -not support L-64.2b 2. support(1) -support L-64.2b
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupport(0), support(1)  

hw10GEOpticsMDSONETSDHCodesL64point2a 1.3.6.1.4.1.2011.5.14.6.3.1.33
Indicate SONET/SDH Codes L-64.2a support or not. Options: 1. notSupport(0) -not support L-64.2a 2. support(1) -support L-64.2a
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupport(0), support(1)  

hw10GEOpticsMDSONETSDHCodesL64point1 1.3.6.1.4.1.2011.5.14.6.3.1.34
Indicate SONET/SDH Codes L-64.1 support or not. Options: 1. notSupport(0) -not support L-64.1 2. support(1) -support L-64.1
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupport(0), support(1)  

hw10GEOpticsMDSONETSDHCodesV64point3 1.3.6.1.4.1.2011.5.14.6.3.1.35
Indicate SONET/SDH Codes V-64.3 support or not. Options: 1. notSupport(0) -not support V-64.3 2. support(1) -support V-64.3
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupport(0), support(1)  

hw10GEOpticsMDSONETSDHCodesV64point2b 1.3.6.1.4.1.2011.5.14.6.3.1.36
Indicate SONET/SDH Codes V-64.2b support or not. Options: 1. notSupport(0) -not support V-64.2b 2. support(1) -support V-64.2b
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupport(0), support(1)  

hw10GEOpticsMDSONETSDHCodesV64point2a 1.3.6.1.4.1.2011.5.14.6.3.1.37
Indicate SONET/SDH Codes V-64.2a support or not. Options: 1. notSupport(0) -not support V-64.2a 2. support(1) -support V-64.2a
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupport(0), support(1)  

hw10GEOpticsMDEncodingRZ 1.3.6.1.4.1.2011.5.14.6.3.1.38
Indicate encoding mechanism RZ support or not. Options: 1. nonEncodingRZ(0) -not support RZ 2. encodingRZ(1) -support RZ
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER nonEncodingRZ(0), encodingRZ(1)  

hw10GEOpticsMDEncodingNRZ 1.3.6.1.4.1.2011.5.14.6.3.1.39
Indicate encoding mechanism NRZ support or not. Options: 1. nonEncodingNRZ(0) -not support NRZ 2. encodingNRZ(1) -support NRZ
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER nonEncodingNRZ(0), encodingNRZ(1)  

hw10GEOpticsMDEncodingSONET 1.3.6.1.4.1.2011.5.14.6.3.1.40
Indicate encoding mechanism SONET support or not. Options: 1. nonEncodingSONET(0) -not support SONET 2. encodingSONET(1) -support SONET
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER nonEncodingSONET(0), encodingSONET(1)  

hw10GEOpticsMDEncoding8B10B 1.3.6.1.4.1.2011.5.14.6.3.1.41
Indicate encoding mechanism 8B10B support or not. Options: 1. nonEncoding8B10B(0) -not support 8B10B 2. encoding8B10B(1) -support 8B10B
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER nonEncoding8B10B(0), encoding8B10B(1)  

hw10GEOpticsMDEncoding64B 1.3.6.1.4.1.2011.5.14.6.3.1.42
Indicate encoding mechanism 64B/66B support or not. Options: 1. nonEncoding64B(0) -not support 64B/66B 2. encoding64B(1) -support 64B/66B
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER nonEncoding64B(0), encoding64B(1)  

hw10GEOpticsMDBrMin 1.3.6.1.4.1.2011.5.14.6.3.1.43
Minimum bit rate. Unit: 100 MBits/s
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hw10GEOpticsMDBrMax 1.3.6.1.4.1.2011.5.14.6.3.1.44
Maximum bit rate. Unit: 100 MBits/s
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hw10GEOpticsMDSupportLenSMF 1.3.6.1.4.1.2011.5.14.6.3.1.45
Indicate the link length that is supported by the transceiver with the applicable standards using Single-mode Fiber.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hw10GEOpticsMDSupportLenE50um 1.3.6.1.4.1.2011.5.14.6.3.1.46
Indicate the link length that is supported by the transceiver with the applicable standards using 2000MHz*km (850nm) extended bandwidth 50 micron core multimode fiber. Unit: 2m
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hw10GEOpticsMDSupportLen50um 1.3.6.1.4.1.2011.5.14.6.3.1.47
This value specifies the link length that is supported by the transceiver with the applicable standards using 500MHz*km (850 and 1310nm) 50 micron core multimode fiber. Unit: 1m
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hw10GEOpticsMDSupportLen62p5um 1.3.6.1.4.1.2011.5.14.6.3.1.48
This value specifies the link length that is supported by the transceiver with the applicable standards using 200MHz*km (850 nm)/500 MHz*km (1310 nm) 62.5 micron core multimode fiber. Unit: 1m
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hw10GEOpticsMDSupportLenCopper 1.3.6.1.4.1.2011.5.14.6.3.1.49
Indicate the minimum link length that is supported by the transceiver with copper cable. Unit: 1m
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hw10GEOpticsMDTransmitterSupport 1.3.6.1.4.1.2011.5.14.6.3.1.50
Indicate the transmitter support tunable or not. Options: 1. nonTunable(0) -transmitter not support tunable 2. tunable(1) -transmitter support tunable
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER nonTunable(0), tunable(1)  

hw10GEOpticsMDDetector 1.3.6.1.4.1.2011.5.14.6.3.1.51
Indicate the Detector is enable or not. Options: 1. nonDetector(0) -detector is disable 2. detector(1) -detector is enable
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER nonDetector(0), detector(1)  

hw10GEOpticsMDCooledTransmitterDevice 1.3.6.1.4.1.2011.5.14.6.3.1.52
Indicate the Cooled transmitter is enable or not. Options: 1. nonSupport(0) -cooled transmitter is disable 2. support(1) -cooled transmitter is enable
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER nonSupport(0), support(1)  

hw10GEOpticsMDWavelengthControl 1.3.6.1.4.1.2011.5.14.6.3.1.53
Indicate the wavelength control support or not. Options: 1. nonSupport(0) -wavelength control not support 2. support(1) -wavelength control support
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER nonSupport(0), support(1)  

hw10GEOpticsMDTransmitterTechnologySupport 1.3.6.1.4.1.2011.5.14.6.3.1.54
Indicate the transmitter technology type. Options: 1. vCSEL850(0) -the transmitter technology type is vCSEL850 2. vCSEL1310(1) -the transmitter technology type is vCSEL1310 3. vCSEL1550(2) -the transmitter technology type is vCSEL1550 4. fP1310(3) -the transmitter technology type is fP1310 5. dFB1310(4) -the transmitter technology type is dFB1310 6. dFB1550(5) -the transmitter technology type is dFB1550 7. eML1310(6) -the transmitter technology type is eML1310 8. eML1550(7) -the transmitter technology type is eML1550 9. cOPPER(8) -the transmitter technology type is cOPPER
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER vCSEL850(0), vCSEL1310(1), vCSEL1550(2), fP1310(3), dFB1310(4), dFB1550(5), eML1310(6), eML1550(7), cOPPER(8)  

hw10GEOpticsMDVendorName 1.3.6.1.4.1.2011.5.14.6.3.1.55
Indicate the vendor name of a 10GE optical module.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..40)  

hw10GEOpticsMDSupportXFIMode 1.3.6.1.4.1.2011.5.14.6.3.1.56
Indicate the XFI loopback mode support or not. Options: 1. nonSupportXFIMode(0) -the XFI loopback mode not support 2. supportXFIMode(1) -the XFI loopback mode support
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER nonSupportXFIMode(0), supportXFIMode(1)  

hw10GEOpticsMDSupportLinesideMode 1.3.6.1.4.1.2011.5.14.6.3.1.57
Indicate the Lineside loopback mode support or not. Options: 1. nonSupportLinesideMode(0) -lineside loopback mode not support 2. supportLinesideMode(1) -lineside loopback mode support
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER nonSupportLinesideMode(0), supportLinesideMode(1)  

hw10GEOpticsMDMaxBitRateSupportedByCDR 1.3.6.1.4.1.2011.5.14.6.3.1.58
Indicate which rate is supported by the CDR. Options: 1. maxBitRateSupportedByCDR11p1(1) -CDR support for 11.1 Gb/s 2. maxBitRateSupportedByCDR10p7(3) -CDR support for 10.7 Gb/s 3. maxBitRateSupportedByCDR10p5(7) -CDR support for 10.5 Gb/s 4. maxBitRateSupportedByCDR10p3(15) -CDR support for 10.3 Gb/s 5. maxBitRateSupportedByCDR9p95(31) -CDR support for 9.95 Gb/s 6. invalid(-1) -invalid value
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER maxBitRateSupportedByCDR11p1(1), maxBitRateSupportedByCDR10p7(3), maxBitRateSupportedByCDR10p5(7), maxBitRateSupportedByCDR10p3(15), maxBitRateSupportedByCDR9p95(31), invalid(-1)  

hw10GEOpticsMDVendorOUI 1.3.6.1.4.1.2011.5.14.6.3.1.59
Indicate the vendor IEEE company ID of a 10GE optical module.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hw10GEOpticsMDVendorPN 1.3.6.1.4.1.2011.5.14.6.3.1.60
Indicate the part number of a 10GE optical module provided by vendor.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..40)  

hw10GEOpticsMDVendorRev 1.3.6.1.4.1.2011.5.14.6.3.1.61
Indicate the revision level for part number provided by vendor.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..40)  

hw10GEOpticsMDWavelength 1.3.6.1.4.1.2011.5.14.6.3.1.62
The laser wavelength.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hw10GEOpticsMDWaveTolerance 1.3.6.1.4.1.2011.5.14.6.3.1.63
The guaranteed +/- range of transmitter output wavelength under all normal operating conditions.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hw10GEOpticsMDMaxCaseTemperature 1.3.6.1.4.1.2011.5.14.6.3.1.64
Maximum Case Temperature in Degrees C.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hw10GEOpticsMDCcbase 1.3.6.1.4.1.2011.5.14.6.3.1.65
Cc-base.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hw10GEOpticsMDMaxDissipation 1.3.6.1.4.1.2011.5.14.6.3.1.66
Maximum Power Dissipation. Max power is 8 bit value * 20 mW.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hw10GEOpticsMDMaxDissipationPowerDownMode 1.3.6.1.4.1.2011.5.14.6.3.1.67
Maximum Total Power Dissipation in Power Down Mode. Max Power is 8 bit value * 10 mW.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hw10GEOpticsMDMaximum5P0VSupply 1.3.6.1.4.1.2011.5.14.6.3.1.68
Maximum current required by +5V Supply.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hw10GEOpticsMDMaximum3P3VSupply 1.3.6.1.4.1.2011.5.14.6.3.1.69
Maximum current required by +3.3V Supply.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hw10GEOpticsMDMaximum1P8VSupply 1.3.6.1.4.1.2011.5.14.6.3.1.70
Maximum current required by +1.8V Supply.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hw10GEOpticsMDMaximum5P2VSupply 1.3.6.1.4.1.2011.5.14.6.3.1.71
Maximum current required by -5.2V Supply.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hw10GEOpticsMDVendorSN 1.3.6.1.4.1.2011.5.14.6.3.1.72
The serial number of a 10GE optical module provided by vendor.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..140)  

hw10GEOpticsMDDateCode 1.3.6.1.4.1.2011.5.14.6.3.1.73
The date code of a 10GE optical module.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..40)  

hw10GEOpticsMDDiagnoMonitorPowerMeasure 1.3.6.1.4.1.2011.5.14.6.3.1.74
Received power measurement type. Options: 1. supportOMA(0) -OMA 2. supportAveragePower(1) -AveragePower
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER supportOMA(0), supportAveragePower(1)  

hw10GEOpticsMDDiagnoMonitorTypeFECBER 1.3.6.1.4.1.2011.5.14.6.3.1.75
Module Respond to FEC BER. Options: 1. nonSupportBER(0) -no BER Support 2. supportBER(1) -BER Support
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER nonSupportBER(0), supportBER(1)  

hw10GEOpticsMDEnhancedOptions 1.3.6.1.4.1.2011.5.14.6.3.1.76
Indicate enhanced Options. Options: 1. cmu(0) -enhanced options is cmu 2. rateSelect(2) -enhanced options is rateSelect 3. fec(4) -enhanced options is fec 4. vpsby(8) -enhanced options is vpsby 5. rxLOS(16) -enhanced options is rxLOS 6. txFault(32) -enhanced options is txFault 7. txDisable(64) -enhanced options is txDisable 8. alarmFLGIM(128) -enhanced options is alarmFLGIM
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER cmu(0), rateSelect(2), fec(4), vpsby(8), rxLOS(16), txFault(32), txDisable(64), alarmFLGIM(128)  

hw10GEOpticsMDAuxInputOne 1.3.6.1.4.1.2011.5.14.6.3.1.77
Indicate which quantity is monitored by each auxiliary A/D channel one. Options: 1. auxInputType1(0) -Auxiliary monitoring not implemented 2. auxInputType2(1) -APD Bias Voltage 3. auxInputType4(3) -TEC Current (mA) 4. auxInputType5(4) -Laser Temperature 5. auxInputType6(5) -Laser Wavelength 6. auxInputType7(6) -+5V Supply Voltage 7. auxInputType8(7) -+3.3V Supply Voltage 8. auxInputType9(8) -+1.8V Supply Voltage 9. auxInputType10(9) --5.2V Supply Voltage 10. auxInputType11(10) -+5V Supply Current 11. auxInputType14(13) -+3.3V Supply Current 12. auxInputType15(14) -+1.8V Supply Current 13. auxInputType16(15) --5.2V Supply Current
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER auxInputType1(0), auxInputType2(1), auxInputType4(3), auxInputType5(4), auxInputType6(5), auxInputType7(6), auxInputType8(7), auxInputType9(8), auxInputType10(9), auxInputType11(10), auxInputType14(13), auxInputType15(14), auxInputType16(15)  

hw10GEOpticsMDAuxInputTwo 1.3.6.1.4.1.2011.5.14.6.3.1.78
Indicate which quantity is monitored by each auxiliary A/D channel two. Options: 1. auxInputType1(0) -Auxiliary monitoring not implemented 2. auxInputType2(1) -APD Bias Voltage 3. auxInputType4(3) -TEC Current (mA) 4. auxInputType5(4) -Laser Temperature 5. auxInputType6(5) -Laser Wavelength 6. auxInputType7(6) -+5V Supply Voltage 7. auxInputType8(7) -+3.3V Supply Voltage 8. auxInputType9(8) -+1.8V Supply Voltage 9. auxInputType10(9) --5.2V Supply Voltage 10. auxInputType11(10) -+5V Supply Current 11. auxInputType14(13) -+3.3V Supply Current 12. auxInputType15(14) -+1.8V Supply Current 13. auxInputType16(15) --5.2V Supply Current
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER auxInputType1(0), auxInputType2(1), auxInputType4(3), auxInputType5(4), auxInputType6(5), auxInputType7(6), auxInputType8(7), auxInputType9(8), auxInputType10(9), auxInputType11(10), auxInputType14(13), auxInputType15(14), auxInputType16(15)  

hw10GEOpticsMDCCEXT 1.3.6.1.4.1.2011.5.14.6.3.1.79
CC-EXT
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hw10GEOpticsMDVendorSpecific 1.3.6.1.4.1.2011.5.14.6.3.1.80
Vendor of 10GE Optical module specific information.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..140)  

hwOpticsDdmInformationTable 1.3.6.1.4.1.2011.5.14.6.4
Indicates the optical module diagnose information table of an Ethernet port. It is used for querying the diagnose information about the optical module of an Ethernet port. The index of this table is ifindex.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwOpticsDdmInformationEntry

hwOpticsDdmInformationEntry 1.3.6.1.4.1.2011.5.14.6.4.1
Indicates the optical module diagnose information table of an Ethernet port. It is used for querying the diagnose information about the optical module of an Ethernet port. The index of this entry is ifindex.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwOpticsDdmInformationEntry  

hwOpticsTemperature 1.3.6.1.4.1.2011.5.14.6.4.1.1
Temperature. Unit: 0.000001C
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwOpticsSupplyVoltage 1.3.6.1.4.1.2011.5.14.6.4.1.2
Supply voltage. Unit: 0.000001V
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwOpticsTxBiasCurrent 1.3.6.1.4.1.2011.5.14.6.4.1.3
Transmitted bias current. Unit: 0.000001A
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwOpticsTxPower 1.3.6.1.4.1.2011.5.14.6.4.1.4
Transmitted power. Unit: 0.000001dBm
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwOpticsRxPower 1.3.6.1.4.1.2011.5.14.6.4.1.5
Received power. Unit: 0.000001dBm
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hwOpticsMDDdmInfoRemote 1.3.6.1.4.1.2011.5.14.6.4.1.6
Indicates the operation is performed on a remote optical module. Options: 1. remote(1) -the operation is performed on a remote optical module 2. invalid(-1) -invalid value
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER remote(1), invalid(-1)  

hwOpticsPowerThresholdTable 1.3.6.1.4.1.2011.5.14.6.5
Indicates the optical power threshold table of an Ethernet port. It is used for querying, setting, and clearing the optical power threshold of an Ethernet port. After the power threshold is set, the power threshold alarming function of the optical port is enabled. When the optical power is lower than the lower threshold or higher than the upper threshold, an alarm is reported. The index of this table is ifindex.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwOpticsPowerThresholdEntry

hwOpticsPowerThresholdEntry 1.3.6.1.4.1.2011.5.14.6.5.1
Indicates the optical power threshold table of an Ethernet port. It is used for querying, setting, and clearing the optical power threshold of an Ethernet port. After the power threshold is set, the power threshold alarming function of the optical port is enabled. When the optical power is lower than the lower threshold or higher than the upper threshold, an alarm is reported. The index of this entry is ifindex.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwOpticsPowerThresholdEntry  

hwOpticsPowerThresholdValue 1.3.6.1.4.1.2011.5.14.6.5.1.1
TX optical power lower limit threshold value. Unit: 0.000001dBm
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 -99000000..100000000 | 2147483647  

hwOpticsPowerThresholdSwitch 1.3.6.1.4.1.2011.5.14.6.5.1.2
Optical power threshold value Switch. Options: 1. on(1) -set optical power threshold value 2. off(2) -clear optical power threshold value 3. invalid(-1) -invalid value Default: off(2)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2), invalid(-1)  

hwOpticsPowerTxUpperThresholdValue 1.3.6.1.4.1.2011.5.14.6.5.1.3
TX optical power upper limit threshold value. Unit: 0.000001dBm
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 -99000000..100000000 | 2147483647  

hwOpticsPowerRxUpperThresholdValue 1.3.6.1.4.1.2011.5.14.6.5.1.4
RX optical power upper limit threshold value. Unit: 0.000001dBm
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 -99000000..100000000 | 2147483647  

hwOpticsPowerRxLowerThresholdValue 1.3.6.1.4.1.2011.5.14.6.5.1.5
RX optical power lower limit threshold value. Unit: 0.000001dBm
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 -99000000..100000000 | 2147483647  

hwOpticsTemperatureLowerThresholdValue 1.3.6.1.4.1.2011.5.14.6.5.1.6
Optical temperature lower limit threshold value. Unit: 0.01C
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 -9000..30000 | 2147483647  

hwOpticsTemperatureUpperThresholdValue 1.3.6.1.4.1.2011.5.14.6.5.1.7
Optical temperature upper limit threshold value. Unit: 0.01C
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 -9000..30000 | 2147483647  

hwOpticsTemperatureThresholdSwitch 1.3.6.1.4.1.2011.5.14.6.5.1.8
Optical temperature threshold value Switch. Options: 1. on(1) -set optical temparature threshold value 2. off(2) -clear optical temperature threshold value 3. invalid(-1) -invalid value Default: off(2)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2), invalid(-1)  

hwOpticsVoltageLowerThresholdValue 1.3.6.1.4.1.2011.5.14.6.5.1.9
Optical voltage lower limit threshold value. Unit: 0.01V
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..10000 | 2147483647  

hwOpticsVoltageUpperThresholdValue 1.3.6.1.4.1.2011.5.14.6.5.1.10
Optical voltage upper limit threshold value. Unit: 0.01V
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..10000 | 2147483647  

hwOpticsVoltageThresholdSwitch 1.3.6.1.4.1.2011.5.14.6.5.1.11
Optical voltage threshold value Switch. Options: 1. on(1) -set optical voltage threshold value 2. off(2) -clear optical voltage threshold value 3. invalid(-1) -invalid value Default: off(2)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2), invalid(-1)  

hwOpticsCurrentLowerThresholdValue 1.3.6.1.4.1.2011.5.14.6.5.1.12
Optical current lower limit threshold value. Unit: mA
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..10000 | 2147483647  

hwOpticsCurrentUpperThresholdValue 1.3.6.1.4.1.2011.5.14.6.5.1.13
Optical current upper limit threshold value. Unit: mA
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..10000 | 2147483647  

hwOpticsCurrentThresholdSwitch 1.3.6.1.4.1.2011.5.14.6.5.1.14
Optical current threshold value Switch. Options: 1. on(1) -set optical current threshold value 2. off(2) -clear optical current threshold value 3. invalid(-1) -invalid value Default: off(2)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2), invalid(-1)  

hwOpticsModuleTraps 1.3.6.1.4.1.2011.5.14.6.6
OBJECT IDENTIFIER    

hwOpticsCommonTraps 1.3.6.1.4.1.2011.5.14.6.6.1
OBJECT IDENTIFIER    

hwOpticsCommonTrapsPrefix 1.3.6.1.4.1.2011.5.14.6.6.1.0
OBJECT IDENTIFIER    

hwOpticsAlarmTraps 1.3.6.1.4.1.2011.5.14.6.6.2
OBJECT IDENTIFIER    

hwOpticsAlarmTrapsPrefix 1.3.6.1.4.1.2011.5.14.6.6.2.0
OBJECT IDENTIFIER    

hwOpticsTransceiverFaultyAlarmTrap 1.3.6.1.4.1.2011.5.14.6.6.2.0.1
This trap will send when the optical transceiver is faulty.
Status: current Access: read-write
NOTIFICATION-TYPE    

hwOpticsPowerOutOfRangeAlarmTrap 1.3.6.1.4.1.2011.5.14.6.6.2.0.2
This trap will send when the Tx power of the Ethernet optical port is out of the range.
Status: current Access: read-write
NOTIFICATION-TYPE    

hwOpticsPortTemperatureHighAlarmTrap 1.3.6.1.4.1.2011.5.14.6.6.2.0.3
This trap will send when the temperature of the Ethernet optical port is too high.
Status: current Access: read-write
NOTIFICATION-TYPE    

hwOpticsSmartSFPExtModuleInformationTable 1.3.6.1.4.1.2011.5.14.6.7
Indicates the extended information table of a smart SFP optical module. It is used for querying the extend information about a smart SFP optical module and setting loopback of a smart SFP optical module. This operation can be performed on both local and remote optical modules. When this operation is performed on a remote optical module, the hwOpticsSmartSFPExtModuleInfoRemote leaf is required. The index of this table is ifIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwOpticsSmartSFPExtModuleInformationEntry

hwOpticsSmartSFPExtModuleInformationEntry 1.3.6.1.4.1.2011.5.14.6.7.1
Indicates the extended information table of a smart SFP optical module. It is used for querying the extend information about a smart SFP optical module and setting loopback of a smart SFP optical module. This operation can be performed on both local and remote optical modules. When this operation is performed on a remote optical module, the hwOpticsSmartSFPExtModuleInfoRemote leaf is required. The index of this entry is ifIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwOpticsSmartSFPExtModuleInformationEntry  

hwOpticsSmartSFPIdentifier 1.3.6.1.4.1.2011.5.14.6.7.1.1
Indicates the type of a smart SFP optical module. Options: 1. smartSFPI(1) -The optical module is a smart SFP I optical module 2. smartSFPII(2) -The optical module is a smart SFP II optical module 3. unknowType(3) -Unknown or unspecified type
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER smartSFPI(1), smartSFPII(2), unknowType(3)  

hwOpticsSmartSFPProtocolVersion 1.3.6.1.4.1.2011.5.14.6.7.1.2
Indicates the protocol version of a smart SFP optical module. Range: -1, 0-255. -1 is the invalid value.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -1 | 0..255  

hwOpticsSmartSFPSSFPEnhancedOption 1.3.6.1.4.1.2011.5.14.6.7.1.3
Indicates the enhanced options of a smart SFP optical module. Range: -1, 0-65535. -1 is the invalid value.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -1 | 0..65535  

hwOpticsSmartSFPPassword 1.3.6.1.4.1.2011.5.14.6.7.1.4
Indicates the password of a smart SFP optical module.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hwOpticsSmartSFPRemoteControllable 1.3.6.1.4.1.2011.5.14.6.7.1.5
Indicates whether the remote smart SFP optical module can control the local optical module. Options: 1. disable(1) -disable, control command from remote optical module will be ignored 2. enable(2) -enable 3. invalid(-1) -invalid value
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disable(1), enable(2), invalid(-1)  

hwOpticsSmartSFPSubCarrierControl 1.3.6.1.4.1.2011.5.14.6.7.1.6
Indicates sub-carrier control of a smart SFP optical module, that is, whether the local smart SFP optical module can send signals to the remote optical module. Options: 1. disable(1) -disable 2. enable(2) -enable 3. invalid(-1) -invalid value
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disable(1), enable(2), invalid(-1)  

hwOpticsSmartSFPSubCarrierlinkStatus 1.3.6.1.4.1.2011.5.14.6.7.1.7
Indicates the sub-carrier status of a smart SFP optical module. Options: 1. down(1) -linked down 2. rxUp(2) -linked up in RX only 3. up(3) -linked up in both RX and TX direction 4. invalid(-1) -invalid value
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER down(1), rxUp(2), up(3), invalid(-1)  

hwOpticsSmartSFPLocalLoopback 1.3.6.1.4.1.2011.5.14.6.7.1.8
Indicates the loopback control of a local smart SFP optical module. Options: 1. noloop(1) -no loop 2. remote(2) -local outward loop back 3. local(3) -local inward loop back 4. invalid(-1) -invalid value
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noloop(1), remote(2), local(3), invalid(-1)  

hwOpticsSmartSFPRemoteLoopback 1.3.6.1.4.1.2011.5.14.6.7.1.9
Indicates the loopback control of a remote smart SFP optical module. Options: 1. noloop(1) -no loop 2. remote(2) -remote outward loop back 3. invalid(-1) -invalid value
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noloop(1), remote(2), invalid(-1)  

hwOpticsSmartSFPDyingGaspStatus 1.3.6.1.4.1.2011.5.14.6.7.1.10
Indicates the dying-gasp status of a remote smart SFP optical module. Options: 1. poweron(1) -remote normal power 2. poweroff(2) -remote Dying-Gasp asserted 3. invalid(-1) -invalid value
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER poweron(1), poweroff(2), invalid(-1)  

hwOpticsSmartSFPLocalRXOutputControl 1.3.6.1.4.1.2011.5.14.6.7.1.11
Indicates the local output control of a smart SFP optical module. Options: 1. disable(1) -disable 2. enable(2) -enable 3. disableRxLos(3) -disable when LOS asserted 4. invalid(-1) -invalid value
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2), disableRxLos(3), invalid(-1)  

hwOpticsSmartSFPPilottoneControl 1.3.6.1.4.1.2011.5.14.6.7.1.12
Indicates control of outputting attenuation signals by a smart SFP optical module. Options: 1. disable(1) -disable 2. enable(2) -enable 3. invalid(-1) -invalid value
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2), invalid(-1)  

hwOpticsSmartSFPPilottoneStatus 1.3.6.1.4.1.2011.5.14.6.7.1.13
Indicates the carrier loopback detection status of a smart SFP optical module. Options: 1. noSignal(1) -no signal 2. toneDetected(2) -tone detected 3. invalid(-1) -invalid value
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noSignal(1), toneDetected(2), invalid(-1)  

hwOpticsSmartSFPLoopbackdeviceloss 1.3.6.1.4.1.2011.5.14.6.7.1.14
Indicates the optical attenuation of a remote loopback device. Range: -1, 0-25500. -1 is the invalid value. Unit: 0.01db
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -1 | 0..25500  

hwOpticsSmartSFPRoundtripfiberloss 1.3.6.1.4.1.2011.5.14.6.7.1.15
Indicates the optical attenuation of an optical path. Range: -1, 0-25500. -1 is the invalid value. Unit: 0.01db
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -1 | 0..25500  

hwOpticsSmartSFPExtModuleInfoRemote 1.3.6.1.4.1.2011.5.14.6.7.1.16
Indicates the operation is performed on a remote optical module. Options: 1. remote(1) -the operation is performed on a remote optical module 2. invalid(-1) -invalid value
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER remote(1), invalid(-1)  

hwOpticsSmartSFPConfigTable 1.3.6.1.4.1.2011.5.14.6.8
Indicates the configured parameter table of a smart SFP optical module. It is used for querying and setting the configured parameters of a smart SFP optical module. This table supports only the smart SFP 2 optical module. The index of this table is ifIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    HwOpticsSmartSFPConfigEntry

hwOpticsSmartSFPConfigEntry 1.3.6.1.4.1.2011.5.14.6.8.1
Indicates the configured parameter table of a smart SFP optical module. It is used for querying and setting the configured parameters of a smart SFP optical module. This table supports only the smart SFP 2 optical module. The index of this entry is ifIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  HwOpticsSmartSFPConfigEntry  

hwOpticsSmartSFPIILoopOpticloss 1.3.6.1.4.1.2011.5.14.6.8.1.1
Indicates the optical attenuation of a remote loopback device. Unit: 0.01db. Range: -1, 0-25500. -1 is the invalid value. Default: 14000.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 -1 | 0..25500  

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor