HUAWEI-ANCP-AN-EXT-MIB

File: HUAWEI-ANCP-AN-EXT-MIB.mib (36389 bytes)

Imported modules

HUAWEI-MIB	SNMPv2-TC	SNMPv2-SMI
RMON2-MIB	IF-MIB	INET-ADDRESS-MIB
SNMPv2-CONF	GSMP-MIB	HUAWEI-ANCP-AN-MIB

Imported symbols

huaweiMgmt	TruthValue	MODULE-IDENTITY
OBJECT-TYPE	Unsigned32	mib-2
TimeTicks	NOTIFICATION-TYPE	ZeroBasedCounter32
ifIndex	InetAddressType	InetAddress
InetPortNumber	MODULE-COMPLIANCE	OBJECT-GROUP
NOTIFICATION-GROUP	GsmpVersion	GsmpNameType
GsmpPartitionIdType	RowStatus	TEXTUAL-CONVENTION
ancpAnSessionConfigSessionId	ancpAnSessionConfigEntry	ancpAnInterfaceConfigEntry
ancpAnCurrentSessionEntry	ancpAnCurrentSessionAnIpAddressType	ancpAnCurrentSessionAnIpAddress
ancpAnSessionConfigNasIpAddressType	ancpAnSessionConfigNasIpAddress	ancpAnCurrentSessionAnInstance
ancpAnCurrentSessionNasInstance	ancpAnCurrentSessionStartUptime	ancpAnCurrentSessionDiscontinuityTime
ancpAnCurrentSessionStatSentMessages	ancpAnCurrentSessionStatReceivedValidMessages	ancpAnCurrentSessionStatDiscardedMessages

Defined Types

HwAncpAnSessionConfigEntry
SEQUENCE
	hwAncpAnSessionConfigOamThreshold	Unsigned32
	hwAncpAnSessionConfigRollDefaultFlag	TruthValue
	hwAncpAnSessionConfigBandwidthCacSwitch	TruthValue
	hwAncpAnSessionConfigForceNoPartition	TruthValue

HwAncpAnCurrentSessionEntry
SEQUENCE
	hwAncpAnCurrentSessionDiagnostic	INTEGER
	hwAncpAnCurrentSessionPartitionUsedStatus	INTEGER

HwAncpAnInterfaceConfigEntry
SEQUENCE
	hwAncpAnInterfaceEnable	TruthValue
	hwAncpAnInterfaceEncapType	INTEGER
	hwAncpAnInterfacePara1	Unsigned32
	hwAncpAnInterfacePara2	Unsigned32
	hwAncpAnInterfacePara3	Unsigned32

HwAncpAnPartitionEntry
SEQUENCE
	hwAncpAnPartitionId	Unsigned32
	hwAncpAnPartitionInterfaceEncapType	INTEGER
	hwAncpAnPartitionInterfacePara1	Unsigned32
	hwAncpAnPartitionInterfacePara2	Unsigned32
	hwAncpAnPartitionInterfacePara3	Unsigned32

HwAncpAnSessionStatisticEntry
SEQUENCE
	hwAncpAnSessionClearStatistics	INTEGER
	hwAncpAnSessionStatSentSynMessages	ZeroBasedCounter32
	hwAncpAnSessionStatSentSynAckMessages	ZeroBasedCounter32
	hwAncpAnSessionStatSentAckMessages	ZeroBasedCounter32
	hwAncpAnSessionStatSentRstAckMessages	ZeroBasedCounter32
	hwAncpAnSessionStatSentTopoUpMessages	ZeroBasedCounter32
	hwAncpAnSessionStatSentTopoDownMessages	ZeroBasedCounter32
	hwAncpAnSessionStatSentLineCfgMessages	ZeroBasedCounter32
	hwAncpAnSessionStatSentOamMessages	ZeroBasedCounter32
	hwAncpAnSessionStatSentCacMessages	ZeroBasedCounter32
	hwAncpAnSessionStatSentCacThresholdMessages	ZeroBasedCounter32
	hwAncpAnSessionStatSentCacApplyBwMessages	ZeroBasedCounter32
	hwAncpAnSessionStatSentFailedMessages	ZeroBasedCounter32
	hwAncpAnSessionStatRcvdSynMessages	ZeroBasedCounter32
	hwAncpAnSessionStatRcvdSynAckMessages	ZeroBasedCounter32
	hwAncpAnSessionStatRcvdAckMessages	ZeroBasedCounter32
	hwAncpAnSessionStatRcvdRstAckMessages	ZeroBasedCounter32
	hwAncpAnSessionStatRcvdLineCfgMessages	ZeroBasedCounter32
	hwAncpAnSessionStatRcvdOamMessages	ZeroBasedCounter32
	hwAncpAnSessionStatRcvdCacMessages	ZeroBasedCounter32
	hwAncpAnSessionStatRcvdCacThresholdMessages	ZeroBasedCounter32
	hwAncpAnSessionStatRcvdCacBdApplyMessages	ZeroBasedCounter32
	hwAncpAnSessionStatRcvdUnknownMessages	ZeroBasedCounter32

Defined Values

hwAncpAnExtMIB		1.3.6.1.4.1.2011.5.110
The extend MIB module is used for defining Huawei's Access Node Control Protocol (ANCP) MIB objects. ANCP is a dedicated control protocol between NAS and access nodes can facilitate NAS-managed tight QOS control in the access network, simplified OSS infrastructure for service management, optimized multicast replication to enable video services over DSL, subscriber statistics retrieval on the NAS for accounting purposes, and fault isolation capability on the NAS for the underlying access technology. Controllable multicast allows an access device to determine if a user has the authority to watch programs by identifying the user request packets. In this way, the access device controls and forwards the multicast services.
MODULE-IDENTITY

hwAncpAnObjects		1.3.6.1.4.1.2011.5.110.1
OBJECT IDENTIFIER

hwAncpAnTopoDiscoveryMode		1.3.6.1.4.1.2011.5.110.1.1
The object indicates the mode of reporting ANCP topology discovery. Enumerated value. Options: 1. port(1) -indicates the mode of reporting ANCP topology discovery is port 2. servicePort(2) -indicates the mode of reporting ANCP topology discovery is serviceport Default: servicePort(2)
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	port(1), servicePort(2)

hwAncpAnDraftVersion		1.3.6.1.4.1.2011.5.110.1.2
ANCP draft version. Options: 1. draft00(0) -indicates that draft draft-wadhwa-gsmp-l2control-configuration-00 is supported 2. draft01(1) -indicates that draft draft-ietf-ancp-protocol-01 is supported 3. draft02(2) -indicates that draft draft-ietf-ancp-protocol-02 is supported Default: draft01(1)
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	draft00(0), draft01(1), draft02(2)

hwAncpAnPortBegin		1.3.6.1.4.1.2011.5.110.1.3
This object is used to configure the start port ID in the circuit ID information of the ANCP message. Range: 0-1 Default: 0
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	0..1

hwAncpAnSessionConfigTable		1.3.6.1.4.1.2011.5.110.1.4
This table represents the ANCP sessions in the access node. An entry in this table needs to be configured (created) before an ANCP session might be started. The index of this table is ancpAnSessionConfigSessionId.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HwAncpAnSessionConfigEntry

hwAncpAnSessionConfigEntry		1.3.6.1.4.1.2011.5.110.1.4.1
This table represents the ANCP sessions in the access node. An entry in this table needs to be configured (created) before an ANCP session might be started. The index of this entry is ancpAnSessionConfigSessionId.
Status: current	Access: not-accessible
OBJECT-TYPE
	HwAncpAnSessionConfigEntry

hwAncpAnSessionConfigOamThreshold		1.3.6.1.4.1.2011.5.110.1.4.1.1
The OAM threshold in this session. Range: 1-100 Default: 100
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	1..100

hwAncpAnSessionConfigRollDefaultFlag		1.3.6.1.4.1.2011.5.110.1.4.1.2
The flag indicates whether rollback is permitted when link configuration fails. Options: 1. true(1) -rollback is permitted when link configuration fails 2. false(2) -rollback is not permitted when link configuration fails Default: false(2)
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

hwAncpAnSessionConfigBandwidthCacSwitch		1.3.6.1.4.1.2011.5.110.1.4.1.3
The switch of ANCP bandwidthCAC in this session. Options: 1. true(1) 2. false(2) Default: false(2)
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

hwAncpAnSessionConfigForceNoPartition		1.3.6.1.4.1.2011.5.110.1.4.1.4
The switch of ANCP force no partition in this session. Options: 1. true(1) -indicates that the partition is zero in ANCP packet 2. false(2) -indicates that the partition is the configuration in ANCP packet Default: false(2)
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

hwAncpAnCurrentSessionTable		1.3.6.1.4.1.2011.5.110.1.5
It is the Huawei proprietary ANCP session status table. It is queried to obtain the cause of failure to establish a session and check whether the cause is inconsistency in capability set negotiation. It supports the query function. The index of this table is ancpAnSessionConfigSessionId.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HwAncpAnCurrentSessionEntry

hwAncpAnCurrentSessionEntry		1.3.6.1.4.1.2011.5.110.1.5.1
It is the Huawei proprietary ANCP session status table. It is queried to obtain the cause of failure to establish a session and check whether the cause is inconsistency in capability set negotiation. It supports the query function. The index of this entry is ancpAnSessionConfigSessionId.
Status: current	Access: not-accessible
OBJECT-TYPE
	HwAncpAnCurrentSessionEntry

hwAncpAnCurrentSessionDiagnostic		1.3.6.1.4.1.2011.5.110.1.5.1.1
This object indicates the diagnose result when a session fails to be established. Options: 1. noDiagnostic(1) -indicates no diagnostic information 2. capabilityNegotiationFailure(2) -indicates capability negotiation failure
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	noDiagnostic(1), capabilityNegotiationFailure(2)

hwAncpAnCurrentSessionPartitionUsedStatus		1.3.6.1.4.1.2011.5.110.1.5.1.2
This object indicates the partition used status. Options: 1. used(1) -the partition is used 2. unused(2) -the partition is unused 3. unknow(255) -the session is not established
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	used(1), unused(2), unknow(255)

hwAncpAnInterfaceConfigTable		1.3.6.1.4.1.2011.5.110.1.6
An entry in the table showing the partition id for a specific user facing interface. The index of this table is ifIndex.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HwAncpAnInterfaceConfigEntry

hwAncpAnInterfaceConfigEntry		1.3.6.1.4.1.2011.5.110.1.6.1
An entry in the table showing the partition id for a specific user facing interface. The index of this entry is ifIndex.
Status: current	Access: not-accessible
OBJECT-TYPE
	HwAncpAnInterfaceConfigEntry

hwAncpAnInterfaceEnable		1.3.6.1.4.1.2011.5.110.1.6.1.1
This object specifies whether the user facing interface is managed by ANCP. Options: 1. true(1) -indicates the user facing interface is managed by ANCP 2. false(2) -indicates the user facing interface is not managed by ANCP
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

hwAncpAnInterfaceEncapType		1.3.6.1.4.1.2011.5.110.1.6.1.2
This object indicates the access type of the user. Options: 1. atm(1) -indicates the access type of user is ATM 2. eth(2) -indicates the access type of user is ETH 3. auto(3) -indicates the access type of user is auto mode. In this mode, the CID reported by ANCP is related with DSL profile 4. invalid(-1) -indicates the access type of user is invalid
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	atm(1), eth(2), auto(3), invalid(-1)

hwAncpAnInterfacePara1		1.3.6.1.4.1.2011.5.110.1.6.1.3
In the case of user interface in ATM access, this parameter is valid indicating the VPI of the user interface.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

hwAncpAnInterfacePara2		1.3.6.1.4.1.2011.5.110.1.6.1.4
In the case of user interface in ATM access, this parameter is valid indicating the VCI of the user interface.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

hwAncpAnInterfacePara3		1.3.6.1.4.1.2011.5.110.1.6.1.5
In the case of user interface in ETH access, this parameter is valid indicating the VLAN of the user.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

hwAncpAnPartitionTable		1.3.6.1.4.1.2011.5.110.1.7
This table is used to configure the circuit IDs in batches for all ports in a certain partition on an access node. This table can only used to get the circuit IDs of one port assoicated with the partition. If you need to obtain the current circuit ID configured for a certain port, you can specify a port to be queried in hwAncpAnInterfaceConfigTable. The index of this table is hwAncpAnPartitionId.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HwAncpAnPartitionEntry

hwAncpAnPartitionEntry		1.3.6.1.4.1.2011.5.110.1.7.1
This table is used to configure the circuit IDs in batches for all ports in a certain partition on an access node. This table can only used to get the circuit IDs of one port assoicated with the partition. If you need to obtain the current circuit ID configured for a certain port, you can specify a port to be queried in hwAncpAnInterfaceConfigTable. The index of this entry is hwAncpAnPartitionId.
Status: current	Access: not-accessible
OBJECT-TYPE
	HwAncpAnPartitionEntry

hwAncpAnPartitionId		1.3.6.1.4.1.2011.5.110.1.7.1.1
This object specifies whether the user facing interface is managed by ANCP.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	0..255

hwAncpAnPartitionInterfaceEncapType		1.3.6.1.4.1.2011.5.110.1.7.1.2
This object indicates the access type of the user. Options: 1. atm(1) -indicates the access type of user is ATM 2. eth(2) -indicates the access type of user is ETH 3. auto(3) -indicates the access type of user is auto mode. In this mode, the CID reported by ANCP is related with DSL profile
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	atm(1), eth(2), auto(3)

hwAncpAnPartitionInterfacePara1		1.3.6.1.4.1.2011.5.110.1.7.1.3
In the case of user interface in ATM access, this parameter is valid indicating the VPI of the user interface. Range: 0-4095
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

hwAncpAnPartitionInterfacePara2		1.3.6.1.4.1.2011.5.110.1.7.1.4
In the case of user interface in ATM access, this parameter is valid indicating the VCI of the user interface. Range: 32-65535
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

hwAncpAnPartitionInterfacePara3		1.3.6.1.4.1.2011.5.110.1.7.1.5
In the case of user interface in ETH access, this parameter is valid indicating the VLAN of the user. Range: 1-4095
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

hwAncpAnSessionStatisticTable		1.3.6.1.4.1.2011.5.110.1.8
It is the Huawei proprietary ANCP session statistics table. It is queried to obtain the ANCP session statistics. It supports the query sand clear functions. The index of this table is ancpAnSessionConfigSessionId.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HwAncpAnSessionStatisticEntry

hwAncpAnSessionStatisticEntry		1.3.6.1.4.1.2011.5.110.1.8.1
It is the Huawei proprietary ANCP session statistics table. It is queried to obtain the ANCP session statistics. It supports the query sand clear functions. The index of this entry is ancpAnSessionConfigSessionId.
Status: current	Access: not-accessible
OBJECT-TYPE
	HwAncpAnSessionStatisticEntry

hwAncpAnSessionClearStatistics		1.3.6.1.4.1.2011.5.110.1.8.1.1
This object allowed clearing the message statistics of the session. Options: 1. clear(1) -clear the message statistics of the session
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	clear(1)

hwAncpAnSessionStatSentSynMessages		1.3.6.1.4.1.2011.5.110.1.8.1.2
The number of messages that in this session have been sent SYN Message.
Status: current	Access: read-only
OBJECT-TYPE
	ZeroBasedCounter32

hwAncpAnSessionStatSentSynAckMessages		1.3.6.1.4.1.2011.5.110.1.8.1.3
The number of messages that in this session have been sent SYNACK Message.
Status: current	Access: read-only
OBJECT-TYPE
	ZeroBasedCounter32

hwAncpAnSessionStatSentAckMessages		1.3.6.1.4.1.2011.5.110.1.8.1.4
The number of messages that in this session have been sent ACK Message.
Status: current	Access: read-only
OBJECT-TYPE
	ZeroBasedCounter32

hwAncpAnSessionStatSentRstAckMessages		1.3.6.1.4.1.2011.5.110.1.8.1.5
The number of messages that in this session have been sent RSTACK Message.
Status: current	Access: read-only
OBJECT-TYPE
	ZeroBasedCounter32

hwAncpAnSessionStatSentTopoUpMessages		1.3.6.1.4.1.2011.5.110.1.8.1.6
The number of messages that in this session have been sent TOPO up Message.
Status: current	Access: read-only
OBJECT-TYPE
	ZeroBasedCounter32

hwAncpAnSessionStatSentTopoDownMessages		1.3.6.1.4.1.2011.5.110.1.8.1.7
The number of messages that in this session have been sent TOPO down Message.
Status: current	Access: read-only
OBJECT-TYPE
	ZeroBasedCounter32

hwAncpAnSessionStatSentLineCfgMessages		1.3.6.1.4.1.2011.5.110.1.8.1.8
The number of messages that in this session have been sent line config Message.
Status: current	Access: read-only
OBJECT-TYPE
	ZeroBasedCounter32

hwAncpAnSessionStatSentOamMessages		1.3.6.1.4.1.2011.5.110.1.8.1.9
The number of messages that in this session have been sent OAM Message.
Status: current	Access: read-only
OBJECT-TYPE
	ZeroBasedCounter32

hwAncpAnSessionStatSentCacMessages		1.3.6.1.4.1.2011.5.110.1.8.1.10
The number of messages that in this session have been sent CAC Message.
Status: current	Access: read-only
OBJECT-TYPE
	ZeroBasedCounter32

hwAncpAnSessionStatSentCacThresholdMessages		1.3.6.1.4.1.2011.5.110.1.8.1.11
The number of messages that in this session have been sent CAC threshold Message.
Status: current	Access: read-only
OBJECT-TYPE
	ZeroBasedCounter32

hwAncpAnSessionStatSentCacApplyBwMessages		1.3.6.1.4.1.2011.5.110.1.8.1.12
The number of messages that in this session have been sent CAC bandwidth apply Message.
Status: current	Access: read-only
OBJECT-TYPE
	ZeroBasedCounter32

hwAncpAnSessionStatSentFailedMessages		1.3.6.1.4.1.2011.5.110.1.8.1.13
The number of messages that in this session have been sent failed Message.
Status: current	Access: read-only
OBJECT-TYPE
	ZeroBasedCounter32

hwAncpAnSessionStatRcvdSynMessages		1.3.6.1.4.1.2011.5.110.1.8.1.14
The number of messages that in this session have been received SYN Message.
Status: current	Access: read-only
OBJECT-TYPE
	ZeroBasedCounter32

hwAncpAnSessionStatRcvdSynAckMessages		1.3.6.1.4.1.2011.5.110.1.8.1.15
The number of messages that in this session have been received SYNACK Message.
Status: current	Access: read-only
OBJECT-TYPE
	ZeroBasedCounter32

hwAncpAnSessionStatRcvdAckMessages		1.3.6.1.4.1.2011.5.110.1.8.1.16
The number of messages that in this session have been received ACK Message.
Status: current	Access: read-only
OBJECT-TYPE
	ZeroBasedCounter32

hwAncpAnSessionStatRcvdRstAckMessages		1.3.6.1.4.1.2011.5.110.1.8.1.17
The number of messages that in this session have been received RSTACK Message.
Status: current	Access: read-only
OBJECT-TYPE
	ZeroBasedCounter32

hwAncpAnSessionStatRcvdLineCfgMessages		1.3.6.1.4.1.2011.5.110.1.8.1.18
The number of messages that in this session have been received Line Config Message.
Status: current	Access: read-only
OBJECT-TYPE
	ZeroBasedCounter32

hwAncpAnSessionStatRcvdOamMessages		1.3.6.1.4.1.2011.5.110.1.8.1.19
The number of messages that in this session have been received OAM Message.
Status: current	Access: read-only
OBJECT-TYPE
	ZeroBasedCounter32

hwAncpAnSessionStatRcvdCacMessages		1.3.6.1.4.1.2011.5.110.1.8.1.20
The number of messages that in this session have been received CAC Message.
Status: current	Access: read-only
OBJECT-TYPE
	ZeroBasedCounter32

hwAncpAnSessionStatRcvdCacThresholdMessages		1.3.6.1.4.1.2011.5.110.1.8.1.21
The number of messages that in this session have been received CAC threshold Message.
Status: current	Access: read-only
OBJECT-TYPE
	ZeroBasedCounter32

hwAncpAnSessionStatRcvdCacBdApplyMessages		1.3.6.1.4.1.2011.5.110.1.8.1.22
The number of messages that in this session have been received CAC bandwidth apply Message.
Status: current	Access: read-only
OBJECT-TYPE
	ZeroBasedCounter32

hwAncpAnSessionStatRcvdUnknownMessages		1.3.6.1.4.1.2011.5.110.1.8.1.23
The number of messages that in this session have been received failed Message.
Status: current	Access: read-only
OBJECT-TYPE
	ZeroBasedCounter32

hwAncpAnTraps		1.3.6.1.4.1.2011.5.110.1.9
OBJECT IDENTIFIER

hwAncpAnTrapsVbOids		1.3.6.1.4.1.2011.5.110.1.9.0
OBJECT IDENTIFIER

hwAncpAnSessionUpTrapParaNum		1.3.6.1.4.1.2011.5.110.1.9.0.1
Indicates the parameters number of the hwAncpAnSessionUpTrap.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Unsigned32	1..4294967295

hwAncpAnSessionDownTrapParaNum		1.3.6.1.4.1.2011.5.110.1.9.0.2
Indicates the parameters number of the hwAncpAnSessionDownTrap.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Unsigned32	1..4294967295

hwAncpAnCommonTraps		1.3.6.1.4.1.2011.5.110.1.9.1
OBJECT IDENTIFIER

hwAncpAnCommonTrapsPrefix		1.3.6.1.4.1.2011.5.110.1.9.1.0
OBJECT IDENTIFIER

hwAncpAnSessionDownTrap		1.3.6.1.4.1.2011.5.110.1.9.1.0.1
This notification is generated whenever an ANCP session goes down. A session can go down for several reasons: 1) The ANCP session can be deleted by a manager from the ancpAnSessionConfigTable, and hence it will also be removed from the ancpAnCurrentSessionTable. 2) The session can go operational down due to some malfunction in the network, the AN, or the NAS. In this case, the ANCP session will be still in the ancpAnSessionConfigTable and ancpAnCurrentSessionTable, but the ancpAnCurrentSessionState moves from the estab state to another state. This notification is only generated when ancpAnSessionConfigNotifyDnEnable of this session is set to true.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwAncpAnSessionUpTrap		1.3.6.1.4.1.2011.5.110.1.9.1.0.2
This notification is generated when an ANCP session enters the estab state as given by ancpAnCurrentSessionState. Since ancpAnCurrentSessionAnInstance identifies the ANCP session uniquely the other attributes can be derived from this attribute. This notification is only generated when ancpAnSessionConfigNotifyUpEnable of this session is set to true.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

hwAncpAnSessionDiagnosticTrap		1.3.6.1.4.1.2011.5.110.1.9.1.0.3
If the setup of the connection fails, the DSLAM and the BRAS must generate an appropriate fault/alarm message to the network management system.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE