HM2-PLATFORM-ROUTING-MIB

File: HM2-PLATFORM-ROUTING-MIB.mib (142714 bytes)

Imported modules

HM2-TC-MIB IF-MIB INET-ADDRESS-MIB
OSPF-MIB Q-BRIDGE-MIB VRRP-MIB
RFC1213-MIB RIPv2-MIB SNMPv2-SMI
SNMPv2-TC SNMP-FRAMEWORK-MIB

Imported symbols

hm2PlatformMibs HmEnabledStatus ifIndex
InterfaceIndex InterfaceIndexOrZero InetAddress
InetAddressType InetAddressIPv4 ospfIfEntry
ospfNbrEntry ospfVirtIfEntry ospfAreaEntry
ospfIfMetricEntry RouterID VlanId
vrrpOperVrId PhysAddress rip2IfConfEntry
TimeTicks Integer32 Gauge32
IpAddress Counter32 Unsigned32
MODULE-IDENTITY OBJECT-IDENTITY OBJECT-TYPE
DisplayString RowStatus TruthValue
SnmpAdminString

Defined Types

Hm2AgentSwitchLocalProxyArpEntry  
SEQUENCE    
  hm2AgentSwitchLocalProxyArpMode INTEGER

Hm2AgentSwitchIntfArpEntry  
SEQUENCE    
  hm2AgentSwitchIntfArpIpAddress IpAddress
  hm2AgentSwitchIntfArpIfIndex InterfaceIndex
  hm2AgentSwitchIntfArpAge TimeTicks
  hm2AgentSwitchIntfArpMacAddress PhysAddress
  hm2AgentSwitchIntfArpType INTEGER
  hm2AgentSwitchIntfArpStatus RowStatus

Hm2AgentSwitchIpInterfaceEntry  
SEQUENCE    
  hm2AgentSwitchIpInterfaceIfIndex InterfaceIndex
  hm2AgentSwitchIPAddressConfigMethod INTEGER
  hm2AgentSwitchIpInterfaceIpAddress IpAddress
  hm2AgentSwitchIpInterfaceNetMask IpAddress
  hm2AgentSwitchIpInterfaceClearIp HmEnabledStatus
  hm2AgentSwitchIpInterfaceRoutingMode HmEnabledStatus
  hm2AgentSwitchIpInterfaceProxyARPMode HmEnabledStatus
  hm2AgentSwitchIpInterfaceMtuValue Unsigned32
  hm2AgentSwitchIpInterfaceBandwidth Unsigned32
  hm2AgentSwitchIpInterfaceUnnumberedIfIndex InterfaceIndexOrZero
  hm2AgentSwitchIpInterfaceIcmpUnreachables HmEnabledStatus
  hm2AgentSwitchIpInterfaceIcmpRedirects HmEnabledStatus
  hm2AgentSwitchDhcpOperation INTEGER
  hm2AgentSwitchIpInterfaceSuppressed INTEGER
  hm2AgentSwitchIpInterfaceNumberOfFlaps Unsigned32
  hm2AgentSwitchIpInterfaceCurrentPenalty Unsigned32
  hm2AgentSwitchIpInterfaceReUseTime Unsigned32
  hm2AgentSwitchIpInterfaceNetdirectedBCMode HmEnabledStatus

Hm2AgentSwitchIpRouterDiscoveryEntry  
SEQUENCE    
  hm2AgentSwitchIpRouterDiscoveryIfIndex Integer32
  hm2AgentSwitchIpRouterDiscoveryAdvertiseMode INTEGER
  hm2AgentSwitchIpRouterDiscoveryMaxAdvertisementInterval Integer32
  hm2AgentSwitchIpRouterDiscoveryMinAdvertisementInterval Integer32
  hm2AgentSwitchIpRouterDiscoveryAdvertisementLifetime Integer32
  hm2AgentSwitchIpRouterDiscoveryPreferenceLevel Integer32
  hm2AgentSwitchIpRouterDiscoveryAdvertisementAddress IpAddress

Hm2AgentSwitchIpVlanEntry  
SEQUENCE    
  hm2AgentSwitchIpVlanId VlanId
  hm2AgentSwitchIpVlanIfIndex InterfaceIndex
  hm2AgentSwitchIpVlanRoutingStatus RowStatus

Hm2AgentSwitchSecondaryAddressEntry  
SEQUENCE    
  hm2AgentSwitchSecondaryIpAddress IpAddress
  hm2AgentSwitchSecondaryNetMask IpAddress
  hm2AgentSwitchSecondaryStatus RowStatus

Hm2AgentSwitchIntfIpHelperAddressEntry  
SEQUENCE    
  hm2AgentSwitchIntfIpHelperUdpPort Unsigned32
  hm2AgentSwitchIntfIpHelperIpAddress IpAddress
  hm2AgentSwitchIntfIpHelperHitCount Unsigned32
  hm2AgentSwitchIntfIpHelperStatus RowStatus

Hm2AgentRipRouteRedistEntry  
SEQUENCE    
  hm2AgentRipRouteRedistSource INTEGER
  hm2AgentRipRouteRedistMode INTEGER
  hm2AgentRipRouteRedistMetric Integer32
  hm2AgentRipRouteRedistMetricConfigured TruthValue
  hm2AgentRipRouteRedistMatchInternal INTEGER
  hm2AgentRipRouteRedistMatchExternal1 INTEGER
  hm2AgentRipRouteRedistMatchExternal2 INTEGER
  hm2AgentRipRouteRedistMatchNSSAExternal1 INTEGER
  hm2AgentRipRouteRedistMatchNSSAExternal2 INTEGER
  hm2AgentRipRouteRedistDistList Unsigned32
  hm2AgentRipRouteRedistDistListConfigured TruthValue

Hm2AgentRip2IfConfEntry  
SEQUENCE    
  hm2AgentRip2IfConfAuthKeyId Integer32

Hm2AgentOspfRouteRedistEntry  
SEQUENCE    
  hm2AgentOspfRouteRedistSource INTEGER
  hm2AgentOspfRouteRedistMode INTEGER
  hm2AgentOspfRouteRedistMetric Integer32
  hm2AgentOspfRouteRedistMetricConfigured TruthValue
  hm2AgentOspfRouteRedistMetricType INTEGER
  hm2AgentOspfRouteRedistTag Unsigned32
  hm2AgentOspfRouteRedistSubnets TruthValue
  hm2AgentOspfRouteRedistDistList Unsigned32
  hm2AgentOspfRouteRedistDistListConfigured TruthValue

Hm2AgentOspfIfEntry  
SEQUENCE    
  hm2AgentOspfIfAuthKeyId Integer32
  hm2AgentOspfIfIpMtuIgnoreFlag INTEGER
  hm2AgentOspfIfPassiveMode TruthValue
  hm2AgentOspfIfAdvertiseSecondaries INTEGER
  hm2AgentOspfIfFastHelloMode INTEGER

Hm2AgentOspfVirtIfEntry  
SEQUENCE    
  hm2AgentOspfVirtIfAuthKeyId Integer32

Hm2AgentOspfAreaOpaqueLsdbEntry  
SEQUENCE    
  hm2AgentOspfAreaOpaqueLsdbAreaId IpAddress
  hm2AgentOspfAreaOpaqueLsdbType INTEGER
  hm2AgentOspfAreaOpaqueLsdbLsid IpAddress
  hm2AgentOspfAreaOpaqueLsdbRouterId RouterID
  hm2AgentOspfAreaOpaqueLsdbSequence Integer32
  hm2AgentOspfAreaOpaqueLsdbAge Integer32
  hm2AgentOspfAreaOpaqueLsdbChecksum Integer32
  hm2AgentOspfAreaOpaqueLsdbAdvertisement OCTET STRING

Hm2AgentOspfLocalLsdbEntry  
SEQUENCE    
  hm2AgentOspfLocalLsdbIpAddress IpAddress
  hm2AgentOspfLocalLsdbAddressLessIf InterfaceIndexOrZero
  hm2AgentOspfLocalLsdbType INTEGER
  hm2AgentOspfLocalLsdbLsid IpAddress
  hm2AgentOspfLocalLsdbRouterId RouterID
  hm2AgentOspfLocalLsdbSequence Integer32
  hm2AgentOspfLocalLsdbAge Integer32
  hm2AgentOspfLocalLsdbChecksum Integer32
  hm2AgentOspfLocalLsdbAdvertisement OCTET STRING

Hm2AgentOspfAsLsdbEntry  
SEQUENCE    
  hm2AgentOspfAsLsdbType INTEGER
  hm2AgentOspfAsLsdbLsid IpAddress
  hm2AgentOspfAsLsdbRouterId RouterID
  hm2AgentOspfAsLsdbSequence Integer32
  hm2AgentOspfAsLsdbAge Integer32
  hm2AgentOspfAsLsdbChecksum Integer32
  hm2AgentOspfAsLsdbAdvertisement OCTET STRING

Hm2AgentOspfAreaNSSAEntry  
SEQUENCE    
  hm2AgentOspfAreaNSSAImportSummaries HmEnabledStatus
  hm2AgentOspfAreaNSSARedistribute HmEnabledStatus
  hm2AgentOspfAreaNSSADefaultInfoOriginate TruthValue
  hm2AgentOspfAreaNSSADefaultMetric Integer32
  hm2AgentOspfAreaNSSADefaultMetricType INTEGER

Hm2AgentOspfIfMetricEntry  
SEQUENCE    
  hm2AgentOspfIfMetricCalculatedCost Integer32

Hm2AgentRouterVrrpOperEntry  
SEQUENCE    
  hm2AgentRouterVrrpOperPriority Integer32

Hm2AgentSwitchIpHelperAddressEntry  
SEQUENCE    
  hm2AgentSwitchIpHelperUdpPort Unsigned32
  hm2AgentSwitchIpHelperAddress IpAddress
  hm2AgentSwitchIpHelperHitCount Unsigned32
  hm2AgentSwitchIpHelperStatus RowStatus

Hm2AgentSwitchInternalVlanEntry  
SEQUENCE    
  hm2AgentSwitchInternalVlanId VlanId
  hm2AgentSwitchInternalVlanIfIndex InterfaceIndex

Hm2AgentOspfQueueEntry  
SEQUENCE    
  hm2AgentOspfQueueIndex Unsigned32
  hm2AgentOspfQueueName DisplayString
  hm2AgentOspfQueueLength Gauge32
  hm2AgentOspfQueueHigh Gauge32
  hm2AgentOspfQueueDrops Counter32
  hm2AgentOspfQueueLimit Unsigned32

Hm2AgentOspfSpfStatsEntry  
SEQUENCE    
  hm2AgentOspfSpfIndex Unsigned32
  hm2AgentOspfSpfStatsDeltaT Unsigned32
  hm2AgentOspfSpfStatsIntra Unsigned32
  hm2AgentOspfSpfStatsSumm Unsigned32
  hm2AgentOspfSpfStatsExt Unsigned32
  hm2AgentOspfSpfStatsSpfTotal Unsigned32
  hm2AgentOspfSpfStatsRibUpdate Unsigned32
  hm2AgentOspfSpfStatsReason DisplayString

Hm2AgentEcmpCountEntry  
SEQUENCE    
  hm2AgentEcmpNextHopCount Unsigned32
  hm2AgentEcmpRouteCount Gauge32

Hm2AgentOspfNbrEntry  
SEQUENCE    
  hm2AgentOspfNbrDeadTime TimeTicks

Hm2AgentOspfRouteEntry  
SEQUENCE    
  hm2AgentOspfRouteNet InetAddressIPv4
  hm2AgentOspfRouteMask InetAddressIPv4
  hm2AgentOspfRouteCost Integer32
  hm2AgentOspfRouteProtoType INTEGER

Hm2AgentVrrpTrackingEntry  
SEQUENCE    
  hm2AgentVrrpTrackIfIndex Integer32
  hm2AgentVrrpTrackVrid Integer32
  hm2AgentVrrpTrackId SnmpAdminString
  hm2AgentVrrpTrackDecrement Integer32
  hm2AgentVrrpTrackOperStatus INTEGER
  hm2AgentVrrpTrackRowStatus RowStatus

Hm2AgentVrrpExtEntry  
SEQUENCE    
  hm2AgentVrrpExtIfIndex Integer32
  hm2AgentVrrpExtVrid Integer32
  hm2AgentVrrpExtDomainId Integer32
  hm2AgentVrrpExtDomainRole INTEGER
  hm2AgentVrrpExtDomainStatus INTEGER
  hm2AgentVrrpExtAdvertAddress IpAddress
  hm2AgentVrrpExtAdvertTimer Integer32
  hm2AgentVrrpExtCfgPriority Integer32
  hm2AgentVrrpExtNotifyAddress IpAddress
  hm2AgentVrrpExtNotifyLinkdown INTEGER
  hm2AgentVrrpExtPreemptionDelay Integer32
  hm2AgentVrrpPrimaryVirtualAddress IpAddress
  hm2AgentVrrpExtMethod INTEGER

Hm2AgentVrrpDomainEntry  
SEQUENCE    
  hm2AgentVrrpDomainId Integer32
  hm2AgentVrrpDomainMemberSendAdv INTEGER
  hm2AgentVrrpDomainStatus INTEGER
  hm2AgentVrrpDomainSupervisorIfIndex Integer32
  hm2AgentVrrpDomainSupervisorVrid Integer32
  hm2AgentVrrpDomainOperPriority Integer32
  hm2AgentVrrpDomainSupervisorOperState INTEGER

Hm2AgentStaticNeighbourEntry  
SEQUENCE    
  hm2AgentStaticNeighbourAddressType InetAddressType
  hm2AgentStaticNeighbourAddress InetAddress
  hm2AgentStaticNeighbourPhysAddress PhysAddress
  hm2AgentStaticNeighbourIfIndex InterfaceIndexOrZero
  hm2AgentStaticNeighbourRowStatus RowStatus

Hm2AgentDynamicNeighbourEntry  
SEQUENCE    
  hm2AgentDynamicNeighbourAddressType InetAddressType
  hm2AgentDynamicNeighbourAddress InetAddress
  hm2AgentDynamicNeighbourPhysAddress PhysAddress
  hm2AgentDynamicNeighbourIfIndex InterfaceIndexOrZero
  hm2AgentDynamicNeighbourAction INTEGER

Defined Values

hm2PlatformRouting 1.3.6.1.4.1.248.12.2
The Hirschmann Platform2 MIB for Layer3 Switching. Copyright (C) 2011. All Rights Reserved.
MODULE-IDENTITY    

hm2AgentSwitchArpGroup 1.3.6.1.4.1.248.12.2.1
OBJECT IDENTIFIER    

hm2AgentSwitchArpAgeoutTime 1.3.6.1.4.1.248.12.2.1.1
HiOS: Configures the exact ARP entry age-out time in seconds. HiSecOS: Configures the average ARP entry age-out time in seconds, with each entry aging out after a random time between 0.5*hm2AgentSwitchArpAgeoutTime and 1.5*hm2AgentSwitchArpAgeoutTime.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 15..21600  

hm2AgentSwitchArpResponseTime 1.3.6.1.4.1.248.12.2.1.2
Configures the ARP request response timeout in seconds. Allowable range: 1-10
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..10  

hm2AgentSwitchArpMaxRetries 1.3.6.1.4.1.248.12.2.1.3
Configures the ARP count of maximum request for retries. Allowable range: 0-10
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..10  

hm2AgentSwitchArpCacheSize 1.3.6.1.4.1.248.12.2.1.4
Configures the ARP maximum number of entries in the cache. Allowable range is platform specific.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hm2AgentSwitchArpDynamicRenew 1.3.6.1.4.1.248.12.2.1.5
This indicates the current setting of ARP dynamic renew mode.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2AgentSwitchArpTotalEntryCountCurrent 1.3.6.1.4.1.248.12.2.1.6
Current number of entries in the ARP cache.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hm2AgentSwitchArpTotalEntryCountPeak 1.3.6.1.4.1.248.12.2.1.7
Peak number of entries recorded in the ARP cache over time. This value is restarted whenever the ARP cache size is changed.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hm2AgentSwitchArpStaticEntryCountCurrent 1.3.6.1.4.1.248.12.2.1.8
Current number of configured static ARP entries.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hm2AgentSwitchArpStaticEntryCountMax 1.3.6.1.4.1.248.12.2.1.9
Maximum number of configurable static ARP entries.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hm2AgentSwitchLocalProxyArpTable 1.3.6.1.4.1.248.12.2.1.11
This table contains the per-interface configuration parameters for local proxy ARP.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2AgentSwitchLocalProxyArpEntry

hm2AgentSwitchLocalProxyArpEntry 1.3.6.1.4.1.248.12.2.1.11.1
Represents a logical row in the hm2AgentSwitchLocalProxyArpTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2AgentSwitchLocalProxyArpEntry  

hm2AgentSwitchLocalProxyArpMode 1.3.6.1.4.1.248.12.2.1.11.1.1
The local proxy ARP mode for the interface.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2AgentSwitchIntfArpTable 1.3.6.1.4.1.248.12.2.1.12
This table augments the MIB-II ipNetToMediaTable by providing per-interface ARP entry information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2AgentSwitchIntfArpEntry

hm2AgentSwitchIntfArpEntry 1.3.6.1.4.1.248.12.2.1.12.1
This table augments the MIB-II ipNetToMediaTable by providing per-interface ARP entry information.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2AgentSwitchIntfArpEntry  

hm2AgentSwitchIntfArpIpAddress 1.3.6.1.4.1.248.12.2.1.12.1.1
The Type of Address assigned to this interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

hm2AgentSwitchIntfArpIfIndex 1.3.6.1.4.1.248.12.2.1.12.1.2
The Associated IfIndex which identified the ARP Entry. This value must be specified for static ARP entries on an unnumbered interface
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

hm2AgentSwitchIntfArpAge 1.3.6.1.4.1.248.12.2.1.12.1.3
This defines the time (in seconds) since the ARP entry was last refreshed. This value is 0 for ARP entries of type local(1) or static(3), since these entries are not subject to aging.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

hm2AgentSwitchIntfArpMacAddress 1.3.6.1.4.1.248.12.2.1.12.1.4
The hardware MAX Address that each interface maps to.
Status: current Access: read-create
OBJECT-TYPE    
  PhysAddress  

hm2AgentSwitchIntfArpType 1.3.6.1.4.1.248.12.2.1.12.1.5
The type of ARP entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER local(1), gateway(2), static(3), dynamic(4)  

hm2AgentSwitchIntfArpStatus 1.3.6.1.4.1.248.12.2.1.12.1.6
The status of this ARP entry. Setting this object destroy will remove the entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hm2AgentSwitchArpSparseLearn 1.3.6.1.4.1.248.12.2.1.100
This indicates the current setting of ARP sparse learn mode.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2AgentSwitchArpCacheClear 1.3.6.1.4.1.248.12.2.1.101
Setting the object to 'flushARP' will flush the ARP cache. Setting the object to 'flushARPWithGateway' will also flush the ARP cache but includes the ARP entries that are used by gateways of routes. Reading the object always returns 'other'.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), flushARP(2), flushARPWithGateway(3)  

hm2AgentSwitchProxyArpMaxResponseDelay 1.3.6.1.4.1.248.12.2.1.248
Configures the maximum time in ms to wait before a proxy response is sent. Setting this to 0 determines a response to be sent immediately.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0 | 1..1000  

hm2AgentSwitchIpGroup 1.3.6.1.4.1.248.12.2.2
OBJECT IDENTIFIER    

hm2AgentSwitchIpRoutingMode 1.3.6.1.4.1.248.12.2.2.1
Administratively enables/disables routing on the switch.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2AgentSwitchIpDefaultGateway 1.3.6.1.4.1.248.12.2.2.2
Specifies the default gateway manually configured.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

hm2AgentSwitchIpInterfaceTable 1.3.6.1.4.1.248.12.2.2.3
IP interface table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2AgentSwitchIpInterfaceEntry

hm2AgentSwitchIpInterfaceEntry 1.3.6.1.4.1.248.12.2.2.3.1
IP interface entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2AgentSwitchIpInterfaceEntry  

hm2AgentSwitchIpInterfaceIfIndex 1.3.6.1.4.1.248.12.2.2.3.1.1
The IfIndex associated with this instance.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

hm2AgentSwitchIPAddressConfigMethod 1.3.6.1.4.1.248.12.2.2.3.1.2
The source of the IP address. User can set the object to none(0) or dhcp(2). Option dhcp(2) enables DHCP client on the interface. Option none(0) disables DHCP client on the interface. Get on this object returns manual(1) only when the interface has a manually configured address.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), manual(1), dhcp(2)  

hm2AgentSwitchIpInterfaceIpAddress 1.3.6.1.4.1.248.12.2.2.3.1.3
The IP address assigned to this interface. When setting this value, the value of hm2AgentSwitchIpInterfaceNetMask must be set at the same time.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

hm2AgentSwitchIpInterfaceNetMask 1.3.6.1.4.1.248.12.2.2.3.1.4
The netmask assigned to this interface. When setting this value, the value of hm2AgentSwitchIpInterfaceIpAddress must be set at the same time.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

hm2AgentSwitchIpInterfaceClearIp 1.3.6.1.4.1.248.12.2.2.3.1.5
When setting this object to 'enable(1)' the interfaces IP address and netmask will be set back to 0.0.0.0. Reading this object always returns 'disable(2).
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2AgentSwitchIpInterfaceRoutingMode 1.3.6.1.4.1.248.12.2.2.3.1.6
Enables or disables routing for this interface.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2AgentSwitchIpInterfaceProxyARPMode 1.3.6.1.4.1.248.12.2.2.3.1.7
Enables or disables proxy ARP for this interface.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2AgentSwitchIpInterfaceMtuValue 1.3.6.1.4.1.248.12.2.2.3.1.8
Configures the MTU value for this interface. The applicable range is 68 to the , in bytes. Get of this object returns the effective MTU value on the interface. Set of this object with a value of 0 resets the MTU to the default IP MTU value on the interface. If a packet is received where the size exceeds the mtu value, an icmp destination unreachable message is sent back to the sender with the current mtu.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0 | 68..12266  

hm2AgentSwitchIpInterfaceBandwidth 1.3.6.1.4.1.248.12.2.2.3.1.9
Configures the bandwidth value for this interface. If the returned value is 0, bandwidth for this interface is not configured.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..10000000  

hm2AgentSwitchIpInterfaceUnnumberedIfIndex 1.3.6.1.4.1.248.12.2.2.3.1.10
If this object is non-zero, it indicates that the interface is unnumbered and specifies which interface the address is borrowed from.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndexOrZero  

hm2AgentSwitchIpInterfaceIcmpUnreachables 1.3.6.1.4.1.248.12.2.2.3.1.11
If this object is enabled, it indicates that ICMP unreachables can be sent on this interface.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2AgentSwitchIpInterfaceIcmpRedirects 1.3.6.1.4.1.248.12.2.2.3.1.12
If this object is enabled and hm2AgentSwitchIpIcmpRedirectsMode is also enabled, ICMP redirects can be sent on this interface.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2AgentSwitchDhcpOperation 1.3.6.1.4.1.248.12.2.2.3.1.13
Renew or release the IP address learned through DHCP. Get on this object always gives none. None means no operation is performed on DHCP.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER renew(1), release(2), none(3)  

hm2AgentSwitchIpInterfaceSuppressed 1.3.6.1.4.1.248.12.2.2.3.1.14
This mib variable contains the following values, which has the meaning as: 'unsuppressed' - The interface is not suppressed 'suppressed' - The interface is suppressed
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unsuppressed(0), suppressed(1)  

hm2AgentSwitchIpInterfaceNumberOfFlaps 1.3.6.1.4.1.248.12.2.2.3.1.15
This mib variable displays the number of flaps occurred on the interface
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4294967295  

hm2AgentSwitchIpInterfaceCurrentPenalty 1.3.6.1.4.1.248.12.2.2.3.1.16
This mib variable displays the current penalty of an interface
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..20000  

hm2AgentSwitchIpInterfaceReUseTime 1.3.6.1.4.1.248.12.2.2.3.1.17
This mib variable displays the number of seconds until the interface is allowed to come up
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..255  

hm2AgentSwitchIpInterfaceNetdirectedBCMode 1.3.6.1.4.1.248.12.2.2.3.1.248
Enables or disables netdirected broadcasts for this interface.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2AgentSwitchIpRouterDiscoveryTable 1.3.6.1.4.1.248.12.2.2.4
There is no global administrative flag for router discovery. The global routing flag (hm2AgentSwitchIpRoutingMode) will be used for this purpose. If routing is disabled, router discovery is disabled as well.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2AgentSwitchIpRouterDiscoveryEntry

hm2AgentSwitchIpRouterDiscoveryEntry 1.3.6.1.4.1.248.12.2.2.4.1
.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2AgentSwitchIpRouterDiscoveryEntry  

hm2AgentSwitchIpRouterDiscoveryIfIndex 1.3.6.1.4.1.248.12.2.2.4.1.1
Interface Number to configure Router Discovery on.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..2147483647  

hm2AgentSwitchIpRouterDiscoveryAdvertiseMode 1.3.6.1.4.1.248.12.2.2.4.1.2
Enable or disable router discovery on the interface.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2AgentSwitchIpRouterDiscoveryMaxAdvertisementInterval 1.3.6.1.4.1.248.12.2.2.4.1.3
Maximum time allowed between sending router advertisements from the interface.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 4..1800  

hm2AgentSwitchIpRouterDiscoveryMinAdvertisementInterval 1.3.6.1.4.1.248.12.2.2.4.1.4
Minimum time allowed between sending router advertisements from the interface. This value must be less than or equal to hm2AgentSwitchIpRouterDiscoveryMaxAdvertisementInterval.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 3..1800  

hm2AgentSwitchIpRouterDiscoveryAdvertisementLifetime 1.3.6.1.4.1.248.12.2.2.4.1.5
Value of lifetime field of router advertsisement sent from the interface. This value must be greater than or equal to hm2AgentSwitchIpRouterDiscoveryMaxAdvertisementInterval.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 4..9000  

hm2AgentSwitchIpRouterDiscoveryPreferenceLevel 1.3.6.1.4.1.248.12.2.2.4.1.6
Preferability of the address as a default router address, related to other addresses on the same subnet. This is defined as the larger the number, the higher the preference.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hm2AgentSwitchIpRouterDiscoveryAdvertisementAddress 1.3.6.1.4.1.248.12.2.2.4.1.7
Address used when sending router advertisements from the interface.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

hm2AgentSwitchIpVlanTable 1.3.6.1.4.1.248.12.2.2.5
A static VLAN for which routing can be enabled/disabled.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2AgentSwitchIpVlanEntry

hm2AgentSwitchIpVlanEntry 1.3.6.1.4.1.248.12.2.2.5.1
A static VLAN for which routing can be enabled/disabled.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2AgentSwitchIpVlanEntry  

hm2AgentSwitchIpVlanId 1.3.6.1.4.1.248.12.2.2.5.1.1
The VLAN's ID.
Status: current Access: read-only
OBJECT-TYPE    
  VlanId  

hm2AgentSwitchIpVlanIfIndex 1.3.6.1.4.1.248.12.2.2.5.1.2
The IfIndex associated with this VLAN.
Status: current Access: read-write
OBJECT-TYPE    
  InterfaceIndex  

hm2AgentSwitchIpVlanRoutingStatus 1.3.6.1.4.1.248.12.2.2.5.1.3
Status of Routing mode per VLAN. active(1) - VLAN is enabled for routing createAndGo(4) - Adds VLAN entry for routing createAndWait(5) - Adds VLAN entry for routing destroy(6) - Removes VLAN from routing
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hm2AgentSwitchSecondaryAddressTable 1.3.6.1.4.1.248.12.2.2.6
Contains a list of secondary IP addresses associated with an interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2AgentSwitchSecondaryAddressEntry

hm2AgentSwitchSecondaryAddressEntry 1.3.6.1.4.1.248.12.2.2.6.1
A secondary IP address for a given interface. This IP address must not conflict with the IP address configured in the hm2AgentSwitchIpInterfaceTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2AgentSwitchSecondaryAddressEntry  

hm2AgentSwitchSecondaryIpAddress 1.3.6.1.4.1.248.12.2.2.6.1.1
The secondary IP address assigned to this interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

hm2AgentSwitchSecondaryNetMask 1.3.6.1.4.1.248.12.2.2.6.1.2
The secondary netmask assigned to this interface. This value must be set during creation and can not be changed.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

hm2AgentSwitchSecondaryStatus 1.3.6.1.4.1.248.12.2.2.6.1.3
Creates a new entry in the secondary address table. Allowed values are: createAndGo(4) - Creates an entry in this table, associating the address with a given interface. The hm2AgentSwitchSecondaryNetMask object must be set during creation. destroy(6) - Removes the associated address from the interface.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hm2AgentSwitchIpIcmpControlGroup 1.3.6.1.4.1.248.12.2.2.8
OBJECT IDENTIFIER    

hm2AgentSwitchIpIcmpEchoReplyMode 1.3.6.1.4.1.248.12.2.2.8.1
Sets the administrative Echo Reply Mode.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2AgentSwitchIpIcmpRedirectsMode 1.3.6.1.4.1.248.12.2.2.8.2
Sets the administrative Mode for sending Redirects.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2AgentSwitchIpIcmpRateLimitInterval 1.3.6.1.4.1.248.12.2.2.8.3
HiOS: Specifies the time interval between tokens being placed in the bucket for ICMP Ratelimit. HiSecOS: Specifies the average minimum time between subsequent ICMP packets for each destination, using a token bucket algorithm. In times without ICMP packets, the tokens accumulate to allow for bursts of up to hm2AgentSwitchIpIcmpRateLimitBurstSize packets.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..2147483647  

hm2AgentSwitchIpIcmpRateLimitBurstSize 1.3.6.1.4.1.248.12.2.2.8.4
HiOS: Specifies the number of tokens to be placed after timeout. HiSecOS: The size of the token bucket, fixed at 6 tokens.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..200  

hm2AgentSwitchIntfIpHelperAddressTable 1.3.6.1.4.1.248.12.2.2.10
Contains a list of IP helper addresses associated with an interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2AgentSwitchIntfIpHelperAddressEntry

hm2AgentSwitchIpFirstActiveAddressType 1.3.6.1.4.1.248.12.2.2.248
The type of hm2AgentSwitchIpFirstActiveAddress.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

hm2AgentSwitchIpFirstActiveAddress 1.3.6.1.4.1.248.12.2.2.249
The lowest ip address of any active routing interface.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress Size(4|16)  

hm2AgentSwitchIpStaticDefaultPref 1.3.6.1.4.1.248.12.2.2.250
The default preference for static routes.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..255  

hm2AgentSwitchIntfIpHelperAddressEntry 1.3.6.1.4.1.248.12.2.2.10.1
An IP helper address for a given interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2AgentSwitchIntfIpHelperAddressEntry  

hm2AgentSwitchIntfIpHelperUdpPort 1.3.6.1.4.1.248.12.2.2.10.1.1
UDP port number. Received packets with this destination UDP port number are forwarded to the helper address in this entry. A relay entry with port 0 allows dhcp, time, winnameserver, tacacs, dns, tftp, netbios-ns and netbios-dgm relay.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 0..65535  

hm2AgentSwitchIntfIpHelperIpAddress 1.3.6.1.4.1.248.12.2.2.10.1.2
An IP helper address for packets received on this interface. An address of 0.0.0.0 identifies the entry as a discard entry. Packets that match a discard entry are dropped.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

hm2AgentSwitchIntfIpHelperHitCount 1.3.6.1.4.1.248.12.2.2.10.1.4
The number of times a packet has been forwarded or discarded according to this entry.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hm2AgentSwitchIntfIpHelperStatus 1.3.6.1.4.1.248.12.2.2.10.1.5
Creates a new entry in the Helper Address table. Allowed values are: createAndGo(4) - Creates an IP helper entry in this table. destroy(6) - Removes the IP helper entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hm2AgentSwitchClearIpDefaultGateway 1.3.6.1.4.1.248.12.2.2.11
Resets the Global Default Gateway address.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

hm2AgentRouterRipConfigGroup 1.3.6.1.4.1.248.12.2.3
OBJECT IDENTIFIER    

hm2AgentRouterRipAdminState 1.3.6.1.4.1.248.12.2.3.1
Sets the administrative mode of RIP in the router.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2AgentRouterRipSplitHorizonMode 1.3.6.1.4.1.248.12.2.3.2
Sets the RIP split horizon operating mode in the router. A value of none(1) means split horizon processing is disabled. When set to simple(2), the simple split horizon technique is used. When set to poisonReverse(3), the split horizon with poison reverse technique is used. The default split horizon mode is simple(2).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(1), simple(2), poisonReverse(3)  

hm2AgentRouterRipAutoSummaryMode 1.3.6.1.4.1.248.12.2.3.3
Sets the RIP auto summarization mode in the router. A value of enable(1) means that routes advertized by this RIP router are combined, or summarized, whenever possible into aggregates. When set to disable(2), routes are not aggregated in RIP updates generated by this router. The default auto summary mode is enable(1).
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2AgentRouterRipHostRoutesAcceptMode 1.3.6.1.4.1.248.12.2.3.4
Sets the RIP host route acceptance mode in the router. A value of enable(1) means that host routes advertized to this RIP router will be accepted (learned) into its routing table. When set to disable(2), host routes advertized in RIP updates from neighboring routers are ignored. The default host routes accept mode is enable(1).
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2AgentRouterRipDefaultMetric 1.3.6.1.4.1.248.12.2.3.5
Default metric of redistributed routes, when RIP redistributes from other protocols. {0} indicates that the parameter is not configured, this value should not be set. Valid range for set is (1..15).
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0 | 1..15  

hm2AgentRouterRipDefaultMetricConfigured 1.3.6.1.4.1.248.12.2.3.6
Flag to determine whether RIP default-metric is configured or not. Set to 'false' to unconfigure the default route metric. Set to 'true' is not allowed.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

hm2AgentRouterRipDefaultInfoOriginate 1.3.6.1.4.1.248.12.2.3.7
Flag to determine, whether RIP can advertise a default-route learned from another protocol.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

hm2AgentRipRouteRedistTable 1.3.6.1.4.1.248.12.2.3.8
This table contains the MIB objects required to configure route-redistribution for RIP. Here, RIP is the Destination protocol and the source protocols can be any of : BGP, OSPF, Static, Connected.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2AgentRipRouteRedistEntry

hm2AgentRipRouteRedistEntry 1.3.6.1.4.1.248.12.2.3.8.1
The entries of the table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2AgentRipRouteRedistEntry  

hm2AgentRipRouteRedistSource 1.3.6.1.4.1.248.12.2.3.8.1.1
Source route, from which RIP can redistribute routes. This object also acts as the identifier for the RIP redistribution Table entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER connected(1), static(2), ospf(3), bgp(4)  

hm2AgentRipRouteRedistMode 1.3.6.1.4.1.248.12.2.3.8.1.2
User enabels/disables route-redistribution for a particular source protocol.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2AgentRipRouteRedistMetric 1.3.6.1.4.1.248.12.2.3.8.1.3
Metric used for redistributing a particular source protocol route into RIP. {0} indicates that the parameter is not configured, this value should not be set. Valid range for set is (1..15).
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0 | 1..15  

hm2AgentRipRouteRedistMetricConfigured 1.3.6.1.4.1.248.12.2.3.8.1.4
Flag to determine whether RIP redistribute-metric is configured or not. Set to 'false' to unconfigure redistribute metric. Set to 'true' is not allowed.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

hm2AgentRipRouteRedistMatchInternal 1.3.6.1.4.1.248.12.2.3.8.1.5
If this flag is true, RIP redistributes OSPF internal routes. It will be non-applicable, when source protocol is other than ospf.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2), not-applicable(3)  

hm2AgentRipRouteRedistMatchExternal1 1.3.6.1.4.1.248.12.2.3.8.1.6
If this flag is true, RIP redistributes OSPF External1 routes. It will be non-applicable, when source protocol is other than ospf.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2), not-applicable(3)  

hm2AgentRipRouteRedistMatchExternal2 1.3.6.1.4.1.248.12.2.3.8.1.7
If this flag is true, RIP redistributes OSPF External2 routes. It will be non-applicable, when source protocol is other than ospf.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2), not-applicable(3)  

hm2AgentRipRouteRedistMatchNSSAExternal1 1.3.6.1.4.1.248.12.2.3.8.1.8
If this flag is true, RIP redistributes OSPF NSSA-External1 routes. It will be non-applicable, when source protocol is other than ospf.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2), not-applicable(3)  

hm2AgentRipRouteRedistMatchNSSAExternal2 1.3.6.1.4.1.248.12.2.3.8.1.9
If this flag is true, RIP redistributes OSPF NSSA-External2 routes. It will be non-applicable, when source protocol is other than ospf.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2), not-applicable(3)  

hm2AgentRipRouteRedistDistList 1.3.6.1.4.1.248.12.2.3.8.1.10
Access-list number of the access-list, which filters routes received from a source-protocol.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0 | 1000..1099  

hm2AgentRipRouteRedistDistListConfigured 1.3.6.1.4.1.248.12.2.3.8.1.11
Flag to determine whether Access-list is configured or not.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

hm2AgentRip2IfConfTable 1.3.6.1.4.1.248.12.2.3.9
A list of subnets which require separate configuration in RIP. Augments rip2IfConfTable in the RIPv2-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2AgentRip2IfConfEntry

hm2AgentRip2IfConfEntry 1.3.6.1.4.1.248.12.2.3.9.1
A Single Routing Domain in a single Subnet. Augments rip2IfConfEntry in RIPv2-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2AgentRip2IfConfEntry  

hm2AgentRip2IfConfAuthKeyId 1.3.6.1.4.1.248.12.2.3.9.1.1
The identifier for the authentication key used on this interface. This field is only meaningful when the RIPv2-MIB rip2IfConfAuthType is md5(3); otherwise, the value is not used.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..255  

hm2AgentRouterRipRoutePref 1.3.6.1.4.1.248.12.2.3.10
The route preference, sometimes called administrative distance, for RIP routes. A route with a preference of 255 is considered unreachable.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..255  

hm2AgentRouterRipUpdateTimerInterval 1.3.6.1.4.1.248.12.2.3.248
Sets the RIP update timer interval in the router. This is the time in seconds between two full routing table update packets.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..1000  

hm2AgentRouterOspfConfigGroup 1.3.6.1.4.1.248.12.2.4
OBJECT IDENTIFIER    

hm2AgentOspfDefaultMetric 1.3.6.1.4.1.248.12.2.4.1
Default metric of redistributed routes, when OSPF redistributes from other protocols. {0} indicates that the parameter is not configured, this value should not be set. Valid range for set is (1..16777214).
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0 | 1..16777214  

hm2AgentOspfDefaultMetricConfigured 1.3.6.1.4.1.248.12.2.4.2
Flag to determine whether OSPF default-metric is configured or not. Set to 'false' to unconfigure the OSPF default-metric. Set to 'true' is not allowed.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

hm2AgentOspfDefaultInfoOriginate 1.3.6.1.4.1.248.12.2.4.3
Flag to determine, whether OSPF can advertise a default-route learned from another protocol.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

hm2AgentOspfDefaultInfoOriginateAlways 1.3.6.1.4.1.248.12.2.4.4
When this flag is true, the router advertises 0.0.0.0/0.0.0.0 always. Without this option, OSPF will only advertise 0.0.0.0/0.0.0.0 if the router's forwarding table contains a default route.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

hm2AgentOspfDefaultInfoOriginateMetric 1.3.6.1.4.1.248.12.2.4.5
Metric of the default route, which OSPF advertises when learned from other protocol. (0) indicates that the parameter is not configured, this value should not be set. Valid range for set is (1..16777214).
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0 | 1..16777214  

hm2AgentOspfDefaultInfoOriginateMetricConfigured 1.3.6.1.4.1.248.12.2.4.6
Flag to determine whether OSPF default-info originate metric is configured or not. Setting to false unconfigures the default route metric. Setting to true is not allowed.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

hm2AgentOspfDefaultInfoOriginateMetricType 1.3.6.1.4.1.248.12.2.4.7
Metric Type of the default route,which OSPF advertises when learned from other protocol. It can be 1(external type 1) or 2(external type 2).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER externalType1(1), externalType2(2)  

hm2AgentOspfRouteRedistTable 1.3.6.1.4.1.248.12.2.4.8
This table contains the MIB objects required to configure route-redistribution for OSPF. Here, OSPF is the Destination protocol and the source protocols can be any of : BGP, RIP, Static, Connected.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2AgentOspfRouteRedistEntry

hm2AgentOspfRouteRedistEntry 1.3.6.1.4.1.248.12.2.4.8.1
The entries of the table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2AgentOspfRouteRedistEntry  

hm2AgentOspfRouteRedistSource 1.3.6.1.4.1.248.12.2.4.8.1.1
Source protocol, from which OSPF can redistribute routes. This object also acts as the identifier for the OSPF redistribution Table entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER connected(1), static(2), rip(3), bgp(4)  

hm2AgentOspfRouteRedistMode 1.3.6.1.4.1.248.12.2.4.8.1.2
User enables/disables route-redistribution for a particular source protocol.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2AgentOspfRouteRedistMetric 1.3.6.1.4.1.248.12.2.4.8.1.3
Metric used for redistributing a particular source protocol route into OSPF.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..16777214  

hm2AgentOspfRouteRedistMetricConfigured 1.3.6.1.4.1.248.12.2.4.8.1.4
Flag to determine whether OSPF redistribute-metric is configured or not.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

hm2AgentOspfRouteRedistMetricType 1.3.6.1.4.1.248.12.2.4.8.1.5
Metric Type of routes,which OSPF redistributes from other source protocols. It can be 1(external type 1) or 2(external type 2).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER externalType1(1), externalType2(2)  

hm2AgentOspfRouteRedistTag 1.3.6.1.4.1.248.12.2.4.8.1.6
It specifies the tag field in routes redistributed by OSPF.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..4294967295  

hm2AgentOspfRouteRedistSubnets 1.3.6.1.4.1.248.12.2.4.8.1.7
If this value is false, then OSPF will not redistribute subnetted routes.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

hm2AgentOspfRouteRedistDistList 1.3.6.1.4.1.248.12.2.4.8.1.8
Access-list number of the access-list, which filters routes received from a source-protocol. HiOS: Valid access list numbers are between 1000 and 1099. HiSecOS: Valid access list numbers are between 1 and 10000.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0 | 1..10000  

hm2AgentOspfRouteRedistDistListConfigured 1.3.6.1.4.1.248.12.2.4.8.1.9
Flag to determine whether Access-list is configured or not.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

hm2AgentOspfIfTable 1.3.6.1.4.1.248.12.2.4.9
The OSPF Interface Table describes the inter- faces from the viewpoint of OSPF. Augments ospfIfTable from the OSPF-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2AgentOspfIfEntry

hm2AgentOspfIfEntry 1.3.6.1.4.1.248.12.2.4.9.1
The OSPF Interface Entry describes one inter- face from the viewpoint of OSPF. Augments ospfIfEntry in OSPF-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2AgentOspfIfEntry  

hm2AgentOspfIfAuthKeyId 1.3.6.1.4.1.248.12.2.4.9.1.1
The identifier for the authentication key used on this interface. This field is only meaningful when the OSPF-MIB ospfIfAuthType is md5(2); otherwise, the value is not used.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..255  

hm2AgentOspfIfIpMtuIgnoreFlag 1.3.6.1.4.1.248.12.2.4.9.1.2
Configures the IP MTU Ignore Flag value for this OSPF interface.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2AgentOspfIfPassiveMode 1.3.6.1.4.1.248.12.2.4.9.1.3
Flag to determine whether the interface is passive. A passive interface will not participate in the OSPF adjacency formation.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

hm2AgentOspfIfAdvertiseSecondaries 1.3.6.1.4.1.248.12.2.4.9.1.4
Configures the advertisability of the secondary addresses configured on this interface.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2AgentOspfIfFastHelloMode 1.3.6.1.4.1.248.12.2.4.9.1.248
Configures the fast hello mode on this interface. If enabled, hello packets are sent every 250ms, ospfIfHelloInterval is ignored. The dead interval and spf delay need to be re-configured accordingly for faster convergence.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2AgentOspfVirtIfTable 1.3.6.1.4.1.248.12.2.4.10
Information about this router's virtual inter- faces. Augments ospfVirtIfTable from the OSPF-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2AgentOspfVirtIfEntry

hm2AgentOspfVirtIfEntry 1.3.6.1.4.1.248.12.2.4.10.1
Information about a single Virtual Interface. Augments ospfVirtIfEntry in OSPF-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2AgentOspfVirtIfEntry  

hm2AgentOspfVirtIfAuthKeyId 1.3.6.1.4.1.248.12.2.4.10.1.1
The identifier for the authentication key used on this virtual interface. This field is only meaningful when the OSPF-MIB ospfVirtIfAuthType is md5(2); otherwise, the value is not used.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..255  

hm2AgentRouterOspfRFC1583CompatibilityMode 1.3.6.1.4.1.248.12.2.4.11
From RFC2328: Controls the preference rules used in Section 16.4 when choosing among multiple AS-external-LSAs advertising the same destination. When set to 'enabled', the preference rules remain those specified by RFC 1583 ([Ref9]). When set to 'disabled', the preference rules are those stated in Section 16.4.1, which prevent routing loops when AS- external-LSAs for the same destination have been originated from different areas. Set to 'enabled' by default. In order to minimize the chance of routing loops, all OSPF routers in an OSPF routing domain should have RFC1583Compatibility set identically. When there are routers present that have not been updated with the functionality specified in Section 16.4.1 of this memo, all routers should have RFC1583Compatibility set to 'enabled'. Otherwise, all routers should have RFC1583Compatibility set to 'disabled', preventing all routing loops.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2AgentOspfSpfDelayTime 1.3.6.1.4.1.248.12.2.4.12
Delay time (in seconds) between when OSPF receives a topology change and when it starts an SPF calculation. It can be an integer from 0 to 65535. The default time is 5 seconds. A value of 0 means that there is no delay; that is, the SPF calculation is started immediately.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

hm2AgentOspfSpfHoldTime 1.3.6.1.4.1.248.12.2.4.13
Minimum time (in seconds) between two consecutive SPF calculations. It can be an integer from 0 to 65535. The default time is 10 seconds. A value of 0 means that there is no delay; that is, two SPF calculations can be done, one immediately after the other.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

hm2AgentOspfAutoCostRefBw 1.3.6.1.4.1.248.12.2.4.14
Auto cost reference bandwidth of the router interfaces for ospf metric calculations. It can be an integer from 1 to 4294967. The default reference bandwidth is 100 Mbps.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..4294967  

hm2AgentOspfOpaqueLsaSupport 1.3.6.1.4.1.248.12.2.4.15
The router's support for Opaque LSA types. This object is persistent and when written the entity SHOULD save the change to non-volatile storage.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

hm2AgentOspfAreaOpaqueLsdbTable 1.3.6.1.4.1.248.12.2.4.16
The OSPF Process's Area Link State Database (LSDB). The LSDB contains type-10 Link State Advertisements from throughout the areas that the device is attached to.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2AgentOspfAreaOpaqueLsdbEntry

hm2AgentOspfAreaOpaqueLsdbEntry 1.3.6.1.4.1.248.12.2.4.16.1
A single AreaOpaque Link State Advertisement.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2AgentOspfAreaOpaqueLsdbEntry  

hm2AgentOspfAreaOpaqueLsdbAreaId 1.3.6.1.4.1.248.12.2.4.16.1.1
The 32 bit identifier of the Area from which the LSA was received.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

hm2AgentOspfAreaOpaqueLsdbType 1.3.6.1.4.1.248.12.2.4.16.1.2
The type of the link state advertisement. Each link state type has a separate advertisement format.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER areaOpaqueLink(10)  

hm2AgentOspfAreaOpaqueLsdbLsid 1.3.6.1.4.1.248.12.2.4.16.1.3
The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

hm2AgentOspfAreaOpaqueLsdbRouterId 1.3.6.1.4.1.248.12.2.4.16.1.4
The 32 bit number that uniquely identifies the originating router in the Autonomous System.
Status: current Access: read-only
OBJECT-TYPE    
  RouterID  

hm2AgentOspfAreaOpaqueLsdbSequence 1.3.6.1.4.1.248.12.2.4.16.1.5
The sequence number field is a signed 32-bit integer. It starts with the value '80000001'h, or -'7FFFFFFF'h, and increments until '7FFFFFFF'h. Thus, a typical sequence number will be very negative. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hm2AgentOspfAreaOpaqueLsdbAge 1.3.6.1.4.1.248.12.2.4.16.1.6
This field is the age of the link state advertisement in seconds.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hm2AgentOspfAreaOpaqueLsdbChecksum 1.3.6.1.4.1.248.12.2.4.16.1.7
This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hm2AgentOspfAreaOpaqueLsdbAdvertisement 1.3.6.1.4.1.248.12.2.4.16.1.8
The entire Link State Advertisement, including its header. Note that for variable length LSAs, SNMP agents may not be able to return the largest string size
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1..65535)  

hm2AgentOspfLocalLsdbTable 1.3.6.1.4.1.248.12.2.4.17
The OSPF Process's Link-Local Link State Database for non-virtual links. This table is identical to the OSPF LSDB Table in format, but contains only Link-Local Link State Advertisements for non-virtual links. The purpose is to allow Link-Local LSAs to be displayed for each non-virtual interface. This table is implemented to support type-9 LSAs which are defined in 'The OSPF Opaque LSA Option'.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2AgentOspfLocalLsdbEntry

hm2AgentOspfLocalLsdbEntry 1.3.6.1.4.1.248.12.2.4.17.1
A single Link State Advertisement.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2AgentOspfLocalLsdbEntry  

hm2AgentOspfLocalLsdbIpAddress 1.3.6.1.4.1.248.12.2.4.17.1.1
The IP Address of the interface from which the LSA was received if the interface is numbered.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

hm2AgentOspfLocalLsdbAddressLessIf 1.3.6.1.4.1.248.12.2.4.17.1.2
The Interface Index of the interface from which the LSA was received if the interface is unnumbered.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndexOrZero  

hm2AgentOspfLocalLsdbType 1.3.6.1.4.1.248.12.2.4.17.1.3
The type of the link state advertisement. Each link state type has a separate advertise- ment format.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER localOpaqueLink(9)  

hm2AgentOspfLocalLsdbLsid 1.3.6.1.4.1.248.12.2.4.17.1.4
The Link State ID is an LS Type Specific field containing a 32 bit identifier in IP address format; it identifies the piece of the routing domain that is being described by the advertisement.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

hm2AgentOspfLocalLsdbRouterId 1.3.6.1.4.1.248.12.2.4.17.1.5
The 32 bit number that uniquely identifies the originating router in the Autonomous System.
Status: current Access: read-only
OBJECT-TYPE    
  RouterID  

hm2AgentOspfLocalLsdbSequence 1.3.6.1.4.1.248.12.2.4.17.1.6
The sequence number field is a signed 32-bit integer. It starts with the value '80000001'h, or -'7FFFFFFF'h, and increments until '7FFFFFFF'h. Thus, a typical sequence number will be very negative. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hm2AgentOspfLocalLsdbAge 1.3.6.1.4.1.248.12.2.4.17.1.7
This field is the age of the link state adver- tisement in seconds.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hm2AgentOspfLocalLsdbChecksum 1.3.6.1.4.1.248.12.2.4.17.1.8
This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connec- tionless datagrams; it is commonly referred to as the Fletcher checksum.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hm2AgentOspfLocalLsdbAdvertisement 1.3.6.1.4.1.248.12.2.4.17.1.9
The entire Link State Advertisement, including its header. Note that for variable length LSAs, SNMP agents may not be able to return the largest string size.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1..65535)  

hm2AgentOspfAsLsdbTable 1.3.6.1.4.1.248.12.2.4.18
The OSPF Process's AS-scope LSA Link State Database. The Database contains the AS-scope Link State Advertisements from throughout the areas that the device is attached to. This table is identical to the OSPF LSDB Table in format, but contains only AS-scope Link State Advertisements. The purpose is to allow AS-scope LSAs to be displayed once for the router rather than once in each non-stub area.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2AgentOspfAsLsdbEntry

hm2AgentOspfAsLsdbEntry 1.3.6.1.4.1.248.12.2.4.18.1
A single Link State Advertisement.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2AgentOspfAsLsdbEntry  

hm2AgentOspfAsLsdbType 1.3.6.1.4.1.248.12.2.4.18.1.1
The type of the link state advertisement. Each link state type has a separate advertise- ment format.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER asOpaqueLink(11)  

hm2AgentOspfAsLsdbLsid 1.3.6.1.4.1.248.12.2.4.18.1.2
The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

hm2AgentOspfAsLsdbRouterId 1.3.6.1.4.1.248.12.2.4.18.1.3
The 32 bit number that uniquely identifies the originating router in the Autonomous System.
Status: current Access: read-only
OBJECT-TYPE    
  RouterID  

hm2AgentOspfAsLsdbSequence 1.3.6.1.4.1.248.12.2.4.18.1.4
The sequence number field is a signed 32-bit integer. It starts with the value '80000001'h, or -'7FFFFFFF'h, and increments until '7FFFFFFF'h. Thus, a typical sequence number will be very negative. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hm2AgentOspfAsLsdbAge 1.3.6.1.4.1.248.12.2.4.18.1.5
This field is the age of the link state adver- tisement in seconds.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hm2AgentOspfAsLsdbChecksum 1.3.6.1.4.1.248.12.2.4.18.1.6
This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connec- tionless datagrams; it is commonly referred to as the Fletcher checksum.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hm2AgentOspfAsLsdbAdvertisement 1.3.6.1.4.1.248.12.2.4.18.1.7
The entire Link State Advertisement, including its header.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1..65535)  

hm2AgentOspfDefaultPassiveMode 1.3.6.1.4.1.248.12.2.4.19
Flag to determine, whether all the interfaces are passive interfaces by default. A passive interface will not participate in the OSPF adjacency formation.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

hm2AgentOspfRoutePrefIntraArea 1.3.6.1.4.1.248.12.2.4.20
The route preference, sometimes called administrative distance, for intra-area OSPFv2 routes. A route with a preference of 255 is considered unreachable.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..255  

hm2AgentOspfRoutePrefInterArea 1.3.6.1.4.1.248.12.2.4.21
The route preference, sometimes called administrative distance, for inter-area OSPFv2 routes. A route with a preference of 255 is considered unreachable.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..255  

hm2AgentOspfRoutePrefExternal 1.3.6.1.4.1.248.12.2.4.22
The route preference, sometimes called administrative distance, for external OSPFv2 routes. A route with a preference of 255 is considered unreachable.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..255  

hm2AgentOspfAreaNSSATable 1.3.6.1.4.1.248.12.2.4.248
Information about all the configured Not-So-Stubby-Area(NSSAs) in OSPF. Augments ospfAreaTable from the OSPF-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2AgentOspfAreaNSSAEntry

hm2AgentOspfAreaNSSAEntry 1.3.6.1.4.1.248.12.2.4.248.1
Information about a single Not-So-Stubby-Area(NSSA). Augments ospfAreaEntry in OSPF-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2AgentOspfAreaNSSAEntry  

hm2AgentOspfAreaNSSAImportSummaries 1.3.6.1.4.1.248.12.2.4.248.1.1
When set to enabled, OSPF's summary routes are imported into the NSSA as Type-3 summary-LSAs. When set to disabled, summary routes are not imported into the NSSA. The default setting is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2AgentOspfAreaNSSARedistribute 1.3.6.1.4.1.248.12.2.4.248.1.2
When set to enabled NSSA ASBRs will not redistribute external routes into the NSSA and they will cease to originate Type-7 external LSAs for external routes.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2AgentOspfAreaNSSADefaultInfoOriginate 1.3.6.1.4.1.248.12.2.4.248.1.3
Determines if the router will originate a Type-7 default LSA into the NSSA. This command will cause a default LSA to be originated only if the router is an NSSA ABR or ASBR.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

hm2AgentOspfAreaNSSADefaultMetric 1.3.6.1.4.1.248.12.2.4.248.1.4
Defines the metric value advertised in the Type-7 default LSA originated by this router
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..16777214  

hm2AgentOspfAreaNSSADefaultMetricType 1.3.6.1.4.1.248.12.2.4.248.1.5
Defines the metric type advertised in the Type-7 default LSA originated by this router
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER ospfMetric(1), comparable(2), nonComparable(3)  

hm2AgentOspfIfMetricTable 1.3.6.1.4.1.248.12.2.4.249
Information about interface metrics.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2AgentOspfIfMetricEntry

hm2AgentOspfIfMetricEntry 1.3.6.1.4.1.248.12.2.4.249.1
Information about interface metrics.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2AgentOspfIfMetricEntry  

hm2AgentOspfIfMetricCalculatedCost 1.3.6.1.4.1.248.12.2.4.249.1.1
Returns the actual cost value used by OSPF for this interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..FFFF  

hm2AgentSnmpTrapFlagsConfigGroupLayer3 1.3.6.1.4.1.248.12.2.5
OBJECT IDENTIFIER    

hm2AgentSnmpVRRPNewMasterTrapFlag 1.3.6.1.4.1.248.12.2.5.1
This flag enables the sending of VRRP new master notification traps.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2AgentSnmpVRRPAuthFailureTrapFlag 1.3.6.1.4.1.248.12.2.5.2
This flag enables the sending of VRRP authentication failure notification traps.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2AgentBootpDhcpRelayGroup 1.3.6.1.4.1.248.12.2.6
OBJECT IDENTIFIER    

hm2AgentBootpDhcpRelayMaxHopCount 1.3.6.1.4.1.248.12.2.6.1
The BOOTP/DHCP Max Hop Count. The relay agent silently discards BOOTREQUEST messages whose hops field exceeds the value 16 assuming that the request is looped through the intermediate agents. The default value is 4.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..16  

hm2AgentBootpDhcpRelayMinWaitTime 1.3.6.1.4.1.248.12.2.6.4
The BOOTP/DHCP Minimum Wait Time. When the BOOTP relay agent receives a BOOTREQUEST message, it MAY use the value of the 'secs' (seconds since client began booting) field of the request as a factor in deciding whether to relay the request or not.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..100  

hm2AgentBootpDhcpRelayCircuitIdOptionMode 1.3.6.1.4.1.248.12.2.6.5
The BOOTP/DHCP Circuit ID Option Mode. This flag is set to enable/disable the network element to add/remove the DHCP Relay agent Circuit ID sub-options.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2AgentECMPGroup 1.3.6.1.4.1.248.12.2.7
OBJECT IDENTIFIER    

hm2AgentECMPOspfMaxPaths 1.3.6.1.4.1.248.12.2.7.1
It sets the number of paths that OSPF can report for a given destination where maxpaths is platform-dependent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

hm2AgentRouterVrrpConfigGroup 1.3.6.1.4.1.248.12.2.8
OBJECT IDENTIFIER    

hm2AgentRouterVrrpAdminState 1.3.6.1.4.1.248.12.2.8.1
Sets the administrative mode of VRRP in the router.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2AgentVrrpOperations 1.3.6.1.4.1.248.12.2.9
OBJECT IDENTIFIER    

hm2AgentRouterVrrpOperTable 1.3.6.1.4.1.248.12.2.9.1
Operations table for a VRRP router which consists of a sequence (i.e., one or more conceptual rows) of `hm2AgentRouterVrrpOperEntry' items.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2AgentRouterVrrpOperEntry

hm2AgentRouterVrrpOperEntry 1.3.6.1.4.1.248.12.2.9.1.1
An entry in the table contains operational priority that is associated with a virtual router.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  Hm2AgentRouterVrrpOperEntry  

hm2AgentRouterVrrpOperPriority 1.3.6.1.4.1.248.12.2.9.1.1.1
This object specifies the operational priority of the VRRP router. This value will be afftected by both the tracking process and the configured priority set by the vrrpOperPriority object.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Integer32 0..255  

hm2AgentRouterVrrpNumberOfFastInst 1.3.6.1.4.1.248.12.2.9.248
Number of VRRP instances with advertisement interval less than one second.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..16  

hm2AgentIpHelperGroup 1.3.6.1.4.1.248.12.2.11
OBJECT IDENTIFIER    

hm2AgentIpHelperAdminMode 1.3.6.1.4.1.248.12.2.11.1
Administratively enable or disable IP helper.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2AgentDhcpClientMsgsReceived 1.3.6.1.4.1.248.12.2.11.2
The Number of DHCP Requests Received. Total number of DHCP requests received from all clients.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hm2AgentDhcpClientMsgsRelayed 1.3.6.1.4.1.248.12.2.11.3
The Number of DHCP Requests Forwarded. Total number of DHCP requests relayed to a server.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hm2AgentDhcpServerMsgsReceived 1.3.6.1.4.1.248.12.2.11.4
The number of DHCP messages received from a server.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hm2AgentDhcpServerMsgsRelayed 1.3.6.1.4.1.248.12.2.11.5
The number of DHCP messages relayed to a server.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hm2AgentUdpClientMsgsReceived 1.3.6.1.4.1.248.12.2.11.6
The number of UDP messages received from all clients.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hm2AgentUdpClientMsgsRelayed 1.3.6.1.4.1.248.12.2.11.7
The number of UDP messages relayed to a server.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hm2AgentSwitchIpHelperAddressTable 1.3.6.1.4.1.248.12.2.11.8
Contains a list of IP helper addresses configured globally.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2AgentSwitchIpHelperAddressEntry

hm2AgentSwitchIpHelperAddressEntry 1.3.6.1.4.1.248.12.2.11.8.1
An IP Helper address that applies to packets received on any interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2AgentSwitchIpHelperAddressEntry  

hm2AgentSwitchIpHelperUdpPort 1.3.6.1.4.1.248.12.2.11.8.1.1
UDP port number. A relay entry with port 0 allows dhcp, time, winnameserver, tacacs, dns, tftp, netbios-ns and netbios-dgm relay.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..65535  

hm2AgentSwitchIpHelperAddress 1.3.6.1.4.1.248.12.2.11.8.1.2
The IP Helper address assigned to this interface.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

hm2AgentSwitchIpHelperHitCount 1.3.6.1.4.1.248.12.2.11.8.1.3
The number of times a packet has been forwarded or discarded according to this entry.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hm2AgentSwitchIpHelperStatus 1.3.6.1.4.1.248.12.2.11.8.1.4
Creates a new entry in the global IP Helper address table. Allowed values are: createAndGo(4) - Creates an IP helper entry in this table. destroy(6) - Removes the IP helper entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hm2AgentUdpClientMsgsTtlExpired 1.3.6.1.4.1.248.12.2.11.9
The number of UDP messages received with an expired TTL.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hm2AgentUdpClientMsgsDiscarded 1.3.6.1.4.1.248.12.2.11.10
The number of UDP messages that matched a discard entry.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hm2AgentInternalVlanGroup 1.3.6.1.4.1.248.12.2.12
OBJECT IDENTIFIER    

hm2AgentInternalVlanBase 1.3.6.1.4.1.248.12.2.12.1
The VLAN ID internally assigned to the first port-based routing interface.
Status: current Access: read-write
OBJECT-TYPE    
  VlanId  

hm2AgentInternalVlanPolicy 1.3.6.1.4.1.248.12.2.12.2
Whether to search up or down from the base VLAN ID for a free VLAN ID to assign to a port-based routing interface.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER ascending(0), descending(1)  

hm2AgentSwitchInternalVlanTable 1.3.6.1.4.1.248.12.2.12.3
Contains a list of VLAN IDs used internally for port-based routing interfaces.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2AgentSwitchInternalVlanEntry

hm2AgentSwitchInternalVlanEntry 1.3.6.1.4.1.248.12.2.12.3.1
A VLAN ID internally assigned to a port-based routing interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2AgentSwitchInternalVlanEntry  

hm2AgentSwitchInternalVlanId 1.3.6.1.4.1.248.12.2.12.3.1.1
A VLAN ID internally assigned to a port-based routing interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  VlanId  

hm2AgentSwitchInternalVlanIfIndex 1.3.6.1.4.1.248.12.2.12.3.1.2
Interface index of port-based routing interface using this VLAN ID.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

hm2AgentOspfQueueGroup 1.3.6.1.4.1.248.12.2.13
OBJECT IDENTIFIER    

hm2AgentOspfQueueTable 1.3.6.1.4.1.248.12.2.13.1
Table lists information about OSPFv2 message queue utilization.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2AgentOspfQueueEntry

hm2AgentOspfQueueEntry 1.3.6.1.4.1.248.12.2.13.1.1
Information on a specific OSPFv2 message queue.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2AgentOspfQueueEntry  

hm2AgentOspfQueueIndex 1.3.6.1.4.1.248.12.2.13.1.1.1
Index value for this message queue.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

hm2AgentOspfQueueName 1.3.6.1.4.1.248.12.2.13.1.1.2
Name of an OSPFv2 message queue.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

hm2AgentOspfQueueLength 1.3.6.1.4.1.248.12.2.13.1.1.3
The number of messages currently in the message queue.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hm2AgentOspfQueueHigh 1.3.6.1.4.1.248.12.2.13.1.1.4
The high water mark of the number of messages in the message queue.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hm2AgentOspfQueueDrops 1.3.6.1.4.1.248.12.2.13.1.1.5
The number of items dropped because the message queue was full.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hm2AgentOspfQueueLimit 1.3.6.1.4.1.248.12.2.13.1.1.6
The maximum number of messages this queue can hold.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hm2AgentOspfPacketStatsGroup 1.3.6.1.4.1.248.12.2.14
OBJECT IDENTIFIER    

hm2AgentOspfCountersCleared 1.3.6.1.4.1.248.12.2.14.1
The time since OSPFv2 counters were last cleared, in seconds.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hm2AgentOspfLsaRetxCount 1.3.6.1.4.1.248.12.2.14.2
The total number of LSAs retransmitted since OSPF counters were last cleared. If the same LSA is retransmitted to multiple neighbors, the count is incremented for each neighbor.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hm2AgentOspfHellosRx 1.3.6.1.4.1.248.12.2.14.3
The total number of OSPFv2 Hello packets received since OSPF counters were last cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hm2AgentOspfHellosTx 1.3.6.1.4.1.248.12.2.14.4
The total number of OSPFv2 Hello packets transmitted since OSPF counters were last cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hm2AgentOspfDdRx 1.3.6.1.4.1.248.12.2.14.5
The total number of OSPFv2 Database Description packets received since OSPF counters were last cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hm2AgentOspfDdTx 1.3.6.1.4.1.248.12.2.14.6
The total number of OSPFv2 Database Description packets transmitted since OSPF counters were last cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hm2AgentOspfLsReqRx 1.3.6.1.4.1.248.12.2.14.7
The total number of OSPFv2 LS Request packets received since OSPF counters were last cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hm2AgentOspfLsReqTx 1.3.6.1.4.1.248.12.2.14.8
The total number of OSPFv2 LS Request packets transmitted since OSPF counters were last cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hm2AgentOspfLsUpdatesRx 1.3.6.1.4.1.248.12.2.14.9
The total number of OSPFv2 LS Update packets received since OSPF counters were last cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hm2AgentOspfLsUpdatesTx 1.3.6.1.4.1.248.12.2.14.10
The total number of OSPFv2 LS Update packets transmitted since OSPF counters were last cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hm2AgentOspfLsAckRx 1.3.6.1.4.1.248.12.2.14.11
The total number of OSPFv2 LS Acknowledgement packets received since OSPF counters were last cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hm2AgentOspfLsAckTx 1.3.6.1.4.1.248.12.2.14.12
The total number of OSPFv2 LS Acknowledgement packets transmitted since OSPF counters were last cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hm2AgentOspfLsUpdatesRxMax 1.3.6.1.4.1.248.12.2.14.13
The maximum rate of OSPFv2 LS Update packets received over any 5-second interval since OSPF counters were last cleared. The rate is given in packets per second (that is, the number of packets received during the 5-second interval, divided by 5).
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hm2AgentOspfLsUpdatesTxMax 1.3.6.1.4.1.248.12.2.14.14
The maximum rate of OSPFv2 LS Update packets transmitted over any 5-second interval since OSPF counters were last cleared. The rate is given in packets per second (that is, the number of packets transmitted during the 5-second interval, divided by 5).
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hm2AgentOspfType1LsasRx 1.3.6.1.4.1.248.12.2.14.15
The number of type 1 (router) LSAs received since OSPF counters were last cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hm2AgentOspfType2LsasRx 1.3.6.1.4.1.248.12.2.14.16
The number of type 2 (network) LSAs received since OSPF counters were last cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hm2AgentOspfType3LsasRx 1.3.6.1.4.1.248.12.2.14.17
The number of type 3 (network summary) LSAs received since OSPF counters were last cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hm2AgentOspfType4LsasRx 1.3.6.1.4.1.248.12.2.14.18
The number of type 4 (ASBR summary) LSAs received since OSPF counters were last cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hm2AgentOspfType5LsasRx 1.3.6.1.4.1.248.12.2.14.19
The number of type 5 (external) LSAs received since OSPF counters were last cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hm2AgentOspfType7LsasRx 1.3.6.1.4.1.248.12.2.14.20
The number of type 7 (NSSA external) LSAs received since OSPF counters were last cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hm2AgentOspfType9LsasRx 1.3.6.1.4.1.248.12.2.14.21
The number of type 9 (Link Opaque) LSAs received since OSPF counters were last cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hm2AgentOspfType10LsasRx 1.3.6.1.4.1.248.12.2.14.22
The number of type 10 (Area Opaque) LSAs received since OSPF counters were last cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hm2AgentOspfType11LsasRx 1.3.6.1.4.1.248.12.2.14.23
The number of type 11 (AS Opaque) LSAs received since OSPF counters were last cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hm2AgentOspfSpfStatsTable 1.3.6.1.4.1.248.12.2.15
Contains statistics for the twenty most recent SPF runs. Statistics are reported from the oldest SPF first to the most recent.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2AgentOspfSpfStatsEntry

hm2AgentOspfSpfStatsEntry 1.3.6.1.4.1.248.12.2.15.1
Statistics for a single SPF run.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2AgentOspfSpfStatsEntry  

hm2AgentOspfSpfIndex 1.3.6.1.4.1.248.12.2.15.1.1
Integer that uniquely identifies an SPF run. This value is incremented each time OSPF runs a full routing table calculation.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

hm2AgentOspfSpfStatsDeltaT 1.3.6.1.4.1.248.12.2.15.1.2
How long since this routing table calculation ran. The time is given in seconds.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hm2AgentOspfSpfStatsIntra 1.3.6.1.4.1.248.12.2.15.1.3
Number of milliseconds to compute intra-area routes.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hm2AgentOspfSpfStatsSumm 1.3.6.1.4.1.248.12.2.15.1.4
Number of milliseconds to compute inter-area routes.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hm2AgentOspfSpfStatsExt 1.3.6.1.4.1.248.12.2.15.1.5
Number of milliseconds to compute external routes.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hm2AgentOspfSpfStatsSpfTotal 1.3.6.1.4.1.248.12.2.15.1.6
Number of milliseconds for entire routing table calculation.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hm2AgentOspfSpfStatsRibUpdate 1.3.6.1.4.1.248.12.2.15.1.7
Number of milliseconds to update the common routing table.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hm2AgentOspfSpfStatsReason 1.3.6.1.4.1.248.12.2.15.1.8
Reasons why a routing table calculation was required. R - new router LSA, N - new Network LSA, SN - new network summary LSA, SA - new ASBR summary LSA, X - new external LSA.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

hm2AgentRoutingHeapGroup 1.3.6.1.4.1.248.12.2.16
OBJECT IDENTIFIER    

hm2AgentRoutingHeapSize 1.3.6.1.4.1.248.12.2.16.1
The size of the routing heap, in bytes. Unicast routing protocols and ARP allocate memory from the routing heap.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hm2AgentRoutingHeapInUse 1.3.6.1.4.1.248.12.2.16.2
The number of bytes currently allocated from the routing heap.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hm2AgentRoutingHeapHigh 1.3.6.1.4.1.248.12.2.16.3
High water mark for the number of bytes allocated from the routing heap.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hm2AgentRoutingTableSummaryGroup 1.3.6.1.4.1.248.12.2.17
OBJECT IDENTIFIER    

hm2AgentConnectedRoutes 1.3.6.1.4.1.248.12.2.17.1
The number of connected routes in the IPv4 routing table.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hm2AgentStaticRoutes 1.3.6.1.4.1.248.12.2.17.2
The number of static routes in the IPv4 routing table.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hm2AgentRipRoutes 1.3.6.1.4.1.248.12.2.17.3
The number of RIP routes in the IPv4 routing table.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hm2AgentOspfRoutes 1.3.6.1.4.1.248.12.2.17.4
The number of OSPFv2 routes in the IPv4 routing table.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hm2AgentOspfIntraRoutes 1.3.6.1.4.1.248.12.2.17.5
The number of OSPFv2 intra-area routes in the IPv4 routing table.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hm2AgentOspfInterRoutes 1.3.6.1.4.1.248.12.2.17.6
The number of OSPFv2 inter-area routes in the IPv4 routing table.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hm2AgentOspfExt1Routes 1.3.6.1.4.1.248.12.2.17.7
The number of OSPFv2 external type 1 routes in the IPv4 routing table.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hm2AgentOspfExt2Routes 1.3.6.1.4.1.248.12.2.17.8
The number of OSPFv2 external type 2 routes in the IPv4 routing table.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hm2AgentBgpRoutes 1.3.6.1.4.1.248.12.2.17.9
The number of BGP routes in the IPv4 routing table.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hm2AgentEbgpRoutes 1.3.6.1.4.1.248.12.2.17.10
The number of external BGP routes in the IPv4 routing table.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hm2AgentIbgpRoutes 1.3.6.1.4.1.248.12.2.17.11
The number of internal BGP routes in the IPv4 routing table.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hm2AgentLocalBgpRoutes 1.3.6.1.4.1.248.12.2.17.12
The number of local BGP routes in the IPv4 routing table.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hm2AgentRejectRoutes 1.3.6.1.4.1.248.12.2.17.13
The number of reject routes in the IPv4 routing table.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hm2AgentTotalRoutes 1.3.6.1.4.1.248.12.2.17.14
The number of routes in the IPv4 routing table.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hm2AgentBestRoutes 1.3.6.1.4.1.248.12.2.17.15
The number of IPv4 routes in the forwarding table.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hm2AgentBestRoutesHigh 1.3.6.1.4.1.248.12.2.17.16
The highest number of IPv4 routes in the forwarding table.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hm2AgentAlternateRoutes 1.3.6.1.4.1.248.12.2.17.17
The number of alternate routes in the IPv4 routing table. An alternate route is less preferred than the best route and is not used for forwarding.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hm2AgentRouteAdds 1.3.6.1.4.1.248.12.2.17.18
The number of routes added to the IPv4 routing table.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hm2AgentRouteModifies 1.3.6.1.4.1.248.12.2.17.19
The number of routes changed in the IPv4 routing table.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hm2AgentRouteDeletes 1.3.6.1.4.1.248.12.2.17.20
The number of routes removed from the IPv4 routing table.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hm2AgentUnresolvedRouteAdds 1.3.6.1.4.1.248.12.2.17.21
The number of IPv4 route adds that failed because none of the route's next hops were on a local subnet.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hm2AgentInvalidRouteAdds 1.3.6.1.4.1.248.12.2.17.22
The number of IPv4 routes adds that failed because the route was invalid.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hm2AgentFailedRouteAdds 1.3.6.1.4.1.248.12.2.17.23
The number of IPv4 routes adds that failed because of a resource limitation in the routing table
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hm2AgentReservedLocals 1.3.6.1.4.1.248.12.2.17.24
The number of IPv4 routing table entries reserved for a local subnet on a routing interface that is down.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hm2AgentUniqueNextHops 1.3.6.1.4.1.248.12.2.17.25
The number of distinct next hops used among all IPv4 routes currently in the routing table. These include local interfaces for local routes and neighbors for indirect routes.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hm2AgentUniqueNextHopsHigh 1.3.6.1.4.1.248.12.2.17.26
The highest count of unique next hops since counters were last cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hm2AgentNextHopGroups 1.3.6.1.4.1.248.12.2.17.27
The current number of next hop groups in use by one or more routes. Each next hop group includes one or more next hops.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hm2AgentNextHopGroupsHigh 1.3.6.1.4.1.248.12.2.17.28
The highest count of next hop groups since counters were last cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hm2AgentEcmpGroups 1.3.6.1.4.1.248.12.2.17.29
The number of next hop groups with multiple next hops.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hm2AgentEcmpGroupsHigh 1.3.6.1.4.1.248.12.2.17.30
The high water mark of the number of ECMP groups.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hm2AgentEcmpRoutes 1.3.6.1.4.1.248.12.2.17.31
The current number of IPv4 routes with multiple next hops.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hm2AgentTruncEcmpRoutes 1.3.6.1.4.1.248.12.2.17.32
The number of ECMP routes that are currently installed in the forwarding table with just one next hop. The forwarding table may limit the number of ECMP routes or the number of ECMP groups. When an ECMP route cannot be installed because such a limit is reached, the route is installed with a single next hop.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hm2AgentEcmpRetries 1.3.6.1.4.1.248.12.2.17.33
The number of ECMP routes that have been installed in the forwarding table after initially being installed with a single next hop.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

hm2AgentEcmpCountTable 1.3.6.1.4.1.248.12.2.18
A count of the number of routes with each number of ECMP next hops.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2AgentEcmpCountEntry

hm2AgentEcmpCountEntry 1.3.6.1.4.1.248.12.2.18.1
Number of IPv4 routes with a given number of next hops.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2AgentEcmpCountEntry  

hm2AgentEcmpNextHopCount 1.3.6.1.4.1.248.12.2.18.1.1
The number of next hops in a route. From 0 to the maximum number of next hops in an ECMP route. The maximum varies by platform.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 0..128  

hm2AgentEcmpRouteCount 1.3.6.1.4.1.248.12.2.18.1.2
The number of IPv4 routes with agentEcmpNextHopCount next hops.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

hm2AgentOspfStubRouterGroup 1.3.6.1.4.1.248.12.2.19
OBJECT IDENTIFIER    

hm2AgentOspfStubRouterAdvertisement 1.3.6.1.4.1.248.12.2.19.1
Specifies how the router LSAs are advertised by the router. The value doNotAdvertise indicates the advertisement of a standard router LSA and is the default value. The value advertise indicates the advertisement of a stub router LSA.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER doNotAdvertise(1), advertise(2)  

hm2AgentOspfStubRouterReason 1.3.6.1.4.1.248.12.2.19.2
This indicates the reason because of which the router is in Stub mode. This is valid only if the agentOspfStubRouterMode is 'active'.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER configured(0), startup(1), resource-limitation(2)  

hm2AgentOspfStubRouterStartupTimeRemaining 1.3.6.1.4.1.248.12.2.19.3
The time remaining (in seconds) for the router to come out of the stub mode. This is valid only if the agentOspfStubRouterReason is 'startup'.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hm2AgentOspfStubRouterDuration 1.3.6.1.4.1.248.12.2.19.4
Time elapsed (in seconds) since the router last entered the stub router mode. This is valid only if the agentOspfStubRouterMode is 'active' and agentOspfStubRouterReason is 'resource-limitation'.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

hm2AgentOspfNbrTable 1.3.6.1.4.1.248.12.2.249
Information about this router's neighbors. Augments ospfNbrTable from the OSPF-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2AgentOspfNbrEntry

hm2AgentOspfNbrEntry 1.3.6.1.4.1.248.12.2.249.1
Information about a single neighbor. Augments ospfNbrEntry in OSPF-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2AgentOspfNbrEntry  

hm2AgentOspfNbrDeadTime 1.3.6.1.4.1.248.12.2.249.1.1
The neighbor's Dead Time is the amount of remaining time since the last OSPF hello packet received, before declaring the neighbor status as down.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

hm2AgentOspfRouteTable 1.3.6.1.4.1.248.12.2.250
Information about this router's OSPF routes.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2AgentOspfRouteEntry

hm2AgentOspfRouteEntry 1.3.6.1.4.1.248.12.2.250.1
Information about a single route.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2AgentOspfRouteEntry  

hm2AgentOspfRouteNet 1.3.6.1.4.1.248.12.2.250.1.1
The IP Address of the Net or Subnet indicated by the route.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddressIPv4  

hm2AgentOspfRouteMask 1.3.6.1.4.1.248.12.2.250.1.2
The Subnet Mask that pertains to the Net or Subnet.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddressIPv4  

hm2AgentOspfRouteCost 1.3.6.1.4.1.248.12.2.250.1.3
The route cost calculated in the SPF algorithm to reach the network.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hm2AgentOspfRouteProtoType 1.3.6.1.4.1.248.12.2.250.1.4
The type of route that was learned from OSPF.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER intra(1), inter(2), ext-type1(3), ext-type2(4), nssa-type1(5), nssa-type2(6)  

hm2AgentVrrpExtGroup 1.3.6.1.4.1.248.12.2.260
OBJECT IDENTIFIER    

hm2AgentVrrpTrackingTable 1.3.6.1.4.1.248.12.2.260.1
This table contains variables to define an entry in the VRRP Tracking database.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2AgentVrrpTrackingEntry

hm2AgentVrrpTrackingEntry 1.3.6.1.4.1.248.12.2.260.1.1
The entries of the table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2AgentVrrpTrackingEntry  

hm2AgentVrrpTrackIfIndex 1.3.6.1.4.1.248.12.2.260.1.1.1
DURABLE: { 1:all } The interface number of the virtual router
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

hm2AgentVrrpTrackVrid 1.3.6.1.4.1.248.12.2.260.1.1.2
DURABLE: { 1:all } The virtual router id for this virtual router
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..255  

hm2AgentVrrpTrackId 1.3.6.1.4.1.248.12.2.260.1.1.3
DURABLE: { 1:all } The id of the object being tracked
Status: current Access: not-accessible
OBJECT-TYPE    
  SnmpAdminString  

hm2AgentVrrpTrackDecrement 1.3.6.1.4.1.248.12.2.260.1.1.4
DURABLE: { 1:all } The value by wich the current priority of the virtual router is decremented when the tracked object goes DOWN.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..253  

hm2AgentVrrpTrackOperStatus 1.3.6.1.4.1.248.12.2.260.1.1.5
Shows if the tracked object is currently UP or DOWN or NOT-READY
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), notReady(3)  

hm2AgentVrrpTrackRowStatus 1.3.6.1.4.1.248.12.2.260.1.1.6
DURABLE: { 1:all } Defines the status of a vrrp tracking database entry. Set to createAndGo(4) to create a new row. Set to destroy(6) to delete an entry. Reads as active(1) if the tracked object exists and is trackable, notReady(3) otherwise.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hm2AgentVrrpExtTable 1.3.6.1.4.1.248.12.2.260.2
This table contains variables to define an entry in the VRRP enhancements database.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2AgentVrrpExtEntry

hm2AgentVrrpExtEntry 1.3.6.1.4.1.248.12.2.260.2.1
The entry of the hm2AgentVrrpExtTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2AgentVrrpExtEntry  

hm2AgentVrrpExtIfIndex 1.3.6.1.4.1.248.12.2.260.2.1.1
The interface number of the virtual router
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

hm2AgentVrrpExtVrid 1.3.6.1.4.1.248.12.2.260.2.1.2
The virtual router id for this virtual router
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..255  

hm2AgentVrrpExtDomainId 1.3.6.1.4.1.248.12.2.260.2.1.3
The domain this virtual router is a member of. If set to 0, the virtual router is not a member of any domain.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..8  

hm2AgentVrrpExtDomainRole 1.3.6.1.4.1.248.12.2.260.2.1.4
The role of this virtual router in its domain. This is none(1) if the virtual router is not member of a domain, supervisor(3) if it is the supervisor of its domain, member(2) otherwise.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(1), member(2), supervisor(3)  

hm2AgentVrrpExtDomainStatus 1.3.6.1.4.1.248.12.2.260.2.1.5
Shows if the domain configuration is correct for this virtual router
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER noError(1), noSupervisor(2), supervisorDown(3)  

hm2AgentVrrpExtAdvertAddress 1.3.6.1.4.1.248.12.2.260.2.1.6
The IP address advertisements of the virtual router are sent to
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

hm2AgentVrrpExtAdvertTimer 1.3.6.1.4.1.248.12.2.260.2.1.7
This is used to set the interval between advertisements in milliseconds. This accesses the same value as vrrpOperAdvertisementInterval.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 100..255000  

hm2AgentVrrpExtCfgPriority 1.3.6.1.4.1.248.12.2.260.2.1.8
The configured priority of the virtual router. This can be different from the operating priority if tracked objects are down or the virtual router is the ip address owner
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..254  

hm2AgentVrrpExtNotifyAddress 1.3.6.1.4.1.248.12.2.260.2.1.9
The IP address notifications of the virtual router are sent to
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

hm2AgentVrrpExtNotifyLinkdown 1.3.6.1.4.1.248.12.2.260.2.1.10
Enables or disables sending of notification messages if the virtual router's interface goes down.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2AgentVrrpExtPreemptionDelay 1.3.6.1.4.1.248.12.2.260.2.1.11
Time (in seconds) after startup of the virtual router by which the preemption of a Master with a lower priority is delayed.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

hm2AgentVrrpPrimaryVirtualAddress 1.3.6.1.4.1.248.12.2.260.2.1.12
The virtual IP address in the subnet of the primary ip address on the interface. If no match is found, an unspecified virtual address is returned. If no virtual address is configured, 0.0.0.0 is returned.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

hm2AgentVrrpExtMethod 1.3.6.1.4.1.248.12.2.260.2.1.13
The source of the VRRP instance. User can set the object to none(1), config(2), ttdp(3).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(1), config(2), ttdp(3)  

hm2AgentVrrpDomainTable 1.3.6.1.4.1.248.12.2.260.3
This table contains variables to define an entry in the VRRP domain database.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2AgentVrrpDomainEntry

hm2AgentVrrpDomainEntry 1.3.6.1.4.1.248.12.2.260.3.1
The entries of the table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2AgentVrrpDomainEntry  

hm2AgentVrrpDomainId 1.3.6.1.4.1.248.12.2.260.3.1.1
The domain ID.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..8  

hm2AgentVrrpDomainMemberSendAdv 1.3.6.1.4.1.248.12.2.260.3.1.2
DURABLE: { 1:all } Determines if the members of this domain send advertisement packets. If set to disabled(2), only the supervisor of the domain sends packets.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2AgentVrrpDomainStatus 1.3.6.1.4.1.248.12.2.260.3.1.3
Shows if the configuration of the domain is complete.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER noError(1), noSupervisor(2), supervisorDown(3)  

hm2AgentVrrpDomainSupervisorIfIndex 1.3.6.1.4.1.248.12.2.260.3.1.4
The interface number of the supervisor of the domain
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hm2AgentVrrpDomainSupervisorVrid 1.3.6.1.4.1.248.12.2.260.3.1.5
The virtual router id of the supervisor of the domain. 0 if unconfigured
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..255  

hm2AgentVrrpDomainOperPriority 1.3.6.1.4.1.248.12.2.260.3.1.6
The current operating priority of the domain. This can be different from the configured priority if tracked objects are down. For domain members this is the priority of the supervisor of that Domain if the supervisor is configured and up.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..255  

hm2AgentVrrpDomainSupervisorOperState 1.3.6.1.4.1.248.12.2.260.3.1.7
Shows the current operational state of the domain supervisor.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER initialize(1), backup(2), master(3), unknown(4)  

hm2AgentNeighbourGroup 1.3.6.1.4.1.248.12.2.270
OBJECT IDENTIFIER    

hm2AgentStaticNeighbourTable 1.3.6.1.4.1.248.12.2.270.10
.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2AgentStaticNeighbourEntry

hm2AgentStaticNeighbourEntry 1.3.6.1.4.1.248.12.2.270.10.1
.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2AgentStaticNeighbourEntry  

hm2AgentStaticNeighbourAddressType 1.3.6.1.4.1.248.12.2.270.10.1.1
.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddressType  

hm2AgentStaticNeighbourAddress 1.3.6.1.4.1.248.12.2.270.10.1.2
.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddress Size(4|16)  

hm2AgentStaticNeighbourPhysAddress 1.3.6.1.4.1.248.12.2.270.10.1.3
.
Status: current Access: read-create
OBJECT-TYPE    
  PhysAddress Size(0..65535)  

hm2AgentStaticNeighbourIfIndex 1.3.6.1.4.1.248.12.2.270.10.1.4
.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndexOrZero  

hm2AgentStaticNeighbourRowStatus 1.3.6.1.4.1.248.12.2.270.10.1.5
The status of this entry. Setting this object destroy will remove the entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hm2AgentDynamicNeighbourTable 1.3.6.1.4.1.248.12.2.270.11
.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2AgentDynamicNeighbourEntry

hm2AgentDynamicNeighbourEntry 1.3.6.1.4.1.248.12.2.270.11.1
.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2AgentDynamicNeighbourEntry  

hm2AgentDynamicNeighbourAddressType 1.3.6.1.4.1.248.12.2.270.11.1.1
.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddressType  

hm2AgentDynamicNeighbourAddress 1.3.6.1.4.1.248.12.2.270.11.1.2
.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddress Size(4|16)  

hm2AgentDynamicNeighbourPhysAddress 1.3.6.1.4.1.248.12.2.270.11.1.3
.
Status: current Access: read-only
OBJECT-TYPE    
  PhysAddress Size(0..65535)  

hm2AgentDynamicNeighbourIfIndex 1.3.6.1.4.1.248.12.2.270.11.1.4
.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndexOrZero  

hm2AgentDynamicNeighbourAction 1.3.6.1.4.1.248.12.2.270.11.1.5
.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), delete(2), static(3)  

hm2AgentRoutingSNMPExtensionGroup 1.3.6.1.4.1.248.12.2.280
OBJECT IDENTIFIER    

hm2AgentIpHelperTableFullErrorReturn 1.3.6.1.4.1.248.12.2.280.1
The maximum number of IP helper entries has been reached
Status: current Access: read-write
OBJECT-IDENTITY    

hm2AgentIpHelperInvalidServerAddrErrorReturn 1.3.6.1.4.1.248.12.2.280.2
Invalid IP server address.
Status: current Access: read-write
OBJECT-IDENTITY    

hm2AgentRouterOspfDependenciesNotMet 1.3.6.1.4.1.248.12.2.280.3
Cannot modify OSPF admin state on this interface. Set primary IP address.
Status: current Access: read-write
OBJECT-IDENTITY    

hm2AgentRouterOspfRangeTableFullErrorReturn 1.3.6.1.4.1.248.12.2.280.4
The maximum number of area-range entries has been reached.
Status: current Access: read-write
OBJECT-IDENTITY    

hm2AgentRouterOspfVirtNbrTableFullErrorReturn 1.3.6.1.4.1.248.12.2.280.5
The maximum number of virtual neighbor entries has been reached.
Status: current Access: read-write
OBJECT-IDENTITY    

hm2AgentRouterRIPDependenciesNotMet 1.3.6.1.4.1.248.12.2.280.8
Cannot modify RIP admin state on this interface. Set primary IP address.
Status: current Access: read-write
OBJECT-IDENTITY    

hm2AgentIpHelperInvalidUdpPortErrorReturn 1.3.6.1.4.1.248.12.2.280.9
Invalid UDP port.
Status: current Access: read-write
OBJECT-IDENTITY    

hm2AgentStaticNeighbourTableFullErrorReturn 1.3.6.1.4.1.248.12.2.280.10
Static Neighbour Table is full.
Status: current Access: read-write
OBJECT-IDENTITY    

hm2AgentSecondaryAddrNoPrimaryErrorReturn 1.3.6.1.4.1.248.12.2.280.11
Cannot add the secondary IP address because the interface has no primary IP address.
Status: current Access: read-write
OBJECT-IDENTITY    

hm2AgentSecondaryAddrDifferentPrimaryErrorReturn 1.3.6.1.4.1.248.12.2.280.12
The secondary IP address must be different from the primary IP address.
Status: current Access: read-write
OBJECT-IDENTITY    

hm2AgentSecondaryAddrWrongIpClassErrorReturn 1.3.6.1.4.1.248.12.2.280.13
The network number of the secondary IP address is not valid to be used on a routing interface.
Status: current Access: read-write
OBJECT-IDENTITY    

hm2AgentSecondaryAddrWrongSubnetErrorReturn 1.3.6.1.4.1.248.12.2.280.14
All IP addresses on the interface must be from different subnets.
Status: obsolete Access: read-write
OBJECT-IDENTITY    

hm2AgentSecondaryAddrMaxIntfEntriesErrorReturn 1.3.6.1.4.1.248.12.2.280.15
The maximum number of secondary IP addresses on the interface has been reached.
Status: current Access: read-write
OBJECT-IDENTITY    

hm2AgentSecondaryAddrMaxSystemEntriesErrorReturn 1.3.6.1.4.1.248.12.2.280.16
The maximum number of IP addresses on the system has been reached.
Status: current Access: read-write
OBJECT-IDENTITY    

hm2AgentSecondaryAddrStaticRouteErrorReturn 1.3.6.1.4.1.248.12.2.280.17
The secondary IP address is same as the next hop address of a static route.
Status: current Access: read-write
OBJECT-IDENTITY    

hm2AgentSecondaryAddrStaticARPErrorReturn 1.3.6.1.4.1.248.12.2.280.18
The secondary IP address is same as a static ARP entry.
Status: current Access: read-write
OBJECT-IDENTITY    

hm2AgentSecondaryAddrAbsentEntryErrorReturn 1.3.6.1.4.1.248.12.2.280.19
The secondary IP address is not configured on the interface.
Status: current Access: read-write
OBJECT-IDENTITY    

hm2AgentPrimaryAddrWrongIpClassErrorReturn 1.3.6.1.4.1.248.12.2.280.20
The primary IP address is out of the allowed IP class.
Status: current Access: read-write
OBJECT-IDENTITY    

hm2AgentPrimaryAddrConflictErrorReturn 1.3.6.1.4.1.248.12.2.280.21
The primary IP address conflicts with another IP address on a routing interface.
Status: obsolete Access: read-write
OBJECT-IDENTITY    

hm2AgentPrimaryAddrStaticRouteErrorReturn 1.3.6.1.4.1.248.12.2.280.22
The primary IP address is same as the next hop address of a static route.
Status: current Access: read-write
OBJECT-IDENTITY    

hm2AgentPrimaryAddrStaticARPErrorReturn 1.3.6.1.4.1.248.12.2.280.23
The primary IP address is same as a static ARP entry.
Status: current Access: read-write
OBJECT-IDENTITY    

hm2AgentPrimaryAddrExistingSecondaryErrorReturn 1.3.6.1.4.1.248.12.2.280.24
The primary IP address cannot be changed because the interface has secondary IP addresses configured.
Status: current Access: read-write
OBJECT-IDENTITY    

hm2AgentPrimaryAddrNetworkConflictErrorReturn 1.3.6.1.4.1.248.12.2.280.25
The primary IP address conflicts with the management IP address.
Status: obsolete Access: read-write
OBJECT-IDENTITY    

hm2AgentPrimaryAddrRoutingTableFullErrorReturn 1.3.6.1.4.1.248.12.2.280.26
The primary IP address cannot be added because there are no free entries in the routing table.
Status: current Access: read-write
OBJECT-IDENTITY    

hm2AgentDstAddrHostBitSetErrorReturn 1.3.6.1.4.1.248.12.2.280.27
The route cannot be added. Host bits must not be set in the destination. Network address is {0}.
Status: current Access: read-write
OBJECT-IDENTITY    

hm2AgentSamePrefRouteErrorReturn 1.3.6.1.4.1.248.12.2.280.28
Route cannot be added because reject route and next hop route cannot share the same preference.
Status: current Access: read-write
OBJECT-IDENTITY    

hm2AgentVrrpAssoIpAddrRowStatusInconsistentAddress 1.3.6.1.4.1.248.12.2.280.29
The virtual address does not matching the current interface address configuration.
Status: current Access: read-write
OBJECT-IDENTITY    

hm2AgentVrrpAssoIpAddrRowStatusInvalidAddress 1.3.6.1.4.1.248.12.2.280.30
The virtual address is not valid with the current interface address configuration.
Status: current Access: read-write
OBJECT-IDENTITY    

hm2AgentVrrpAssoIpAddrRowStatusUnknownVRID 1.3.6.1.4.1.248.12.2.280.31
Unknown virtual router id.
Status: current Access: read-write
OBJECT-IDENTITY    

hm2AgentSwitchIpRouterDiscMinMaxAdvtIntErrorRtrn 1.3.6.1.4.1.248.12.2.280.32
Min advertisement interval is bigger then max advertisement interval.
Status: current Access: read-write
OBJECT-IDENTITY    

hm2AgentSwitchIpRouterDiscLifeTimeMaxAdvIntErrorRtrn 1.3.6.1.4.1.248.12.2.280.33
Max advertisement interval is bigger then advertisement life time.
Status: current Access: read-write
OBJECT-IDENTITY    

hm2AgentSwitchIpIcmpRateLimitExceedingRatioErrorReturn 1.3.6.1.4.1.248.12.2.280.34
Rate limit ratio exceeds 100 packets per second.
Status: current Access: read-write
OBJECT-IDENTITY    

hm2AgentRouterOspfMaxAreaErrorReturn 1.3.6.1.4.1.248.12.2.280.35
The maximum number of OSPF areas has been reached.
Status: current Access: read-write
OBJECT-IDENTITY    

hm2AgentospfRouterIdChange 1.3.6.1.4.1.248.12.2.280.36
OSPF must be disabled to change the router ID.
Status: current Access: read-write
OBJECT-IDENTITY    

hm2AgentOspfRedistDistList 1.3.6.1.4.1.248.12.2.280.37
Please add a redistribute list.
Status: current Access: read-write
OBJECT-IDENTITY    

hm2AgentOspfDefaultAreaDeleteErrorReturn 1.3.6.1.4.1.248.12.2.280.38
The default area cannot be deleted.
Status: current Access: read-write
OBJECT-IDENTITY    

hm2AgentLocalArpDeleteErrorReturn 1.3.6.1.4.1.248.12.2.280.39
Local ARP entries cannot be deleted.
Status: current Access: read-write
OBJECT-IDENTITY    

hm2AgentDynamicVlanRoutingErrorReturn 1.3.6.1.4.1.248.12.2.280.40
Dynamic VLANs cannot be used for routing interfaces.
Status: current Access: read-write
OBJECT-IDENTITY    

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor