HM2-PLATFORM-MULTICAST-MIB

File: HM2-PLATFORM-MULTICAST-MIB.mib (25727 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC INET-ADDRESS-MIB
IF-MIB PIM-BSR-MIB MGMD-STD-MIB
HM2-TC-MIB PIM-STD-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE OBJECT-IDENTITY
Integer32 Unsigned32 TimeTicks
RowStatus InetAddress InetAddressType
InetAddressPrefixLength InterfaceIndex pimBsrCandidateBSREntry
mgmdHostInterfaceIfIndex mgmdHostInterfaceQuerierType mgmdHostCacheAddressType
mgmdHostCacheAddress mgmdHostCacheIfIndex hm2PlatformMibs
HmEnabledStatus PimGroupMappingOriginType

Defined Types

Hm2AgentMulticastPIMSMGroupMappingEntry  
SEQUENCE    
  hm2AgentMulticastPIMSMGroupMappingGrpAddrType InetAddressType
  hm2AgentMulticastPIMSMGroupMappingGrpAddr InetAddress
  hm2AgentMulticastPIMSMGroupMappingRPAddrType InetAddressType
  hm2AgentMulticastPIMSMGroupMappingRPAddr InetAddress
  hm2AgentMulticastPIMSMGroupMappingOrigin PimGroupMappingOriginType
  hm2AgentMulticastPIMSMGroupMappingGrpPrefixLen InetAddressPrefixLength
  hm2AgentMulticastPIMSMGroupMappingExpiryTime TimeTicks

Hm2AgentIpStaticMRouteEntry  
SEQUENCE    
  hm2AgentIpStaticMRouteSrcAddressType InetAddressType
  hm2AgentIpStaticMRouteSrcIpAddr InetAddress
  hm2AgentIpStaticMRouteSrcNetMask Integer32
  hm2AgentIpStaticMRouteRpfIpAddr InetAddress
  hm2AgentIpStaticMRouteIfIndex InterfaceIndex
  hm2AgentIpStaticMRoutePreference Integer32
  hm2AgentIpStaticMRouteStatus RowStatus
  hm2AgentIpStaticMRouteExtRpfIpAddrType InetAddressType
  hm2AgentIpStaticMRouteExtRpfIpAddr InetAddress

Hm2AgentPIMBsrCandidateConfEntry  
SEQUENCE    
  pimBsrCandidateBSRAdvInterval Unsigned32

Hm2AgentMulticastMgmdExtEntry  
SEQUENCE    
  hm2AgentMulticastMgmdUnsolicitRprtInterval Unsigned32
  hm2AgentMulticastMgmdNumberOfGroups Integer32

Hm2AgentMulticastMgmdHostCacheExtEntry  
SEQUENCE    
  hm2AgentMulticastMgmdHostStatus INTEGER

Defined Values

hm2PlatformMulticast 1.3.6.1.4.1.248.12.4
The Hirschmann Private Platform2 MIB for Layer3 Multicast. Copyright (C) 2013. All Rights Reserved.
MODULE-IDENTITY    

hm2AgentMulticastIGMPConfigGroup 1.3.6.1.4.1.248.12.4.1
OBJECT IDENTIFIER    

hm2AgentMulticastIGMPAdminMode 1.3.6.1.4.1.248.12.4.1.1
This enables or disables IGMP on the system.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2AgentMulticastIGMPProxyOperStatus 1.3.6.1.4.1.248.12.4.1.249
The operating status of IGMP proxy on this device.
Status: current Access: read-only
OBJECT-TYPE    
  HmEnabledStatus  

hm2AgentMulticastPIMSMConfigGroup 1.3.6.1.4.1.248.12.4.3
OBJECT IDENTIFIER    

hm2AgentMulticastPIMSMAdminMode 1.3.6.1.4.1.248.12.4.3.1
This enables or disables PIM Sparse Mode on the system.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2AgentMulticastPIMSMGroupMappingTable 1.3.6.1.4.1.248.12.4.3.249
The (conceptual) table listing BSR-specific information about PIM group mappings learned via C-RP advertisements or created locally using configurations.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2AgentMulticastPIMSMGroupMappingEntry

hm2AgentMulticastPIMSMGroupMappingEntry 1.3.6.1.4.1.248.12.4.3.249.1
An entry (conceptual row) in the hm2AgentMulticastPIMSMGroupMappingTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2AgentMulticastPIMSMGroupMappingEntry  

hm2AgentMulticastPIMSMGroupMappingGrpAddrType 1.3.6.1.4.1.248.12.4.3.249.1.1
The Inet address type of the IP multicast group prefix.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddressType  

hm2AgentMulticastPIMSMGroupMappingGrpAddr 1.3.6.1.4.1.248.12.4.3.249.1.2
The IP multicast group address that, when combined with hm2AgentMulticastPIMSMGroupMappingGrpPrefixLen, gives the group prefix for this mapping. The InetAddressType is given by the hm2AgentMulticastPIMSMGroupMappingGrpAddrType object.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddress Size(4|8|16|20)  

hm2AgentMulticastPIMSMGroupMappingRPAddrType 1.3.6.1.4.1.248.12.4.3.249.1.3
The Inet address type of the RP address.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

hm2AgentMulticastPIMSMGroupMappingRPAddr 1.3.6.1.4.1.248.12.4.3.249.1.4
The IP address of the RP to be used for the given group. The InetAddressType is given by the hm2AgentMulticastPIMSMGroupMappingRPAddrType object.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress Size(4|8|16|20)  

hm2AgentMulticastPIMSMGroupMappingOrigin 1.3.6.1.4.1.248.12.4.3.249.1.5
The mechanism by which the RP for the group was learned.
Status: current Access: read-only
OBJECT-TYPE    
  PimGroupMappingOriginType  

hm2AgentMulticastPIMSMGroupMappingGrpPrefixLen 1.3.6.1.4.1.248.12.4.3.249.1.6
The multicast group prefix length that, when combined with hm2AgentMulticastPIMSMGroupMappingGrpAddr, gives the group prefix for this mapping. If hm2AgentMulticastPIMSMGroupMappingGrpAddrType is 'ipv4' or 'ipv4z', this object must be in the range 4..32. If hm2AgentMulticastPIMSMGroupMappingGrpAddrType is 'ipv6' or 'ipv6z', this object must be in the range 8..128.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressPrefixLength 4..128  

hm2AgentMulticastPIMSMGroupMappingExpiryTime 1.3.6.1.4.1.248.12.4.3.249.1.7
The minimum time remaining before this entry will be aged out. The value zero indicates that this entry will never be aged out.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

hm2AgentMulticastPIMDMConfigGroup 1.3.6.1.4.1.248.12.4.4
OBJECT IDENTIFIER    

hm2AgentMulticastPIMDMAdminMode 1.3.6.1.4.1.248.12.4.4.1
This enables or disables PIM Dense Mode on the system.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2AgentMulticastPIMDMPruneAssertHoldtime 1.3.6.1.4.1.248.12.4.4.248
The value inserted into the Holdtime field of a PIM-DM Prune message sent on any interface.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 60..64800  

hm2AgentMulticastRoutingConfigGroup 1.3.6.1.4.1.248.12.4.5
OBJECT IDENTIFIER    

hm2AgentMulticastRoutingAdminMode 1.3.6.1.4.1.248.12.4.5.1
This enables or disables Multicast Routing Mode on the system.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2AgentMulticastSoftwareDSCP 1.3.6.1.4.1.248.12.4.5.248
Configures the DSCP value that is written into multicast packets that are routed in software. If set to 64, the DSCP value of incoming packets is not changed.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..64  

hm2AgentMulticastDVMRPConfigGroup 1.3.6.1.4.1.248.12.4.6
OBJECT IDENTIFIER    

hm2AgentMulticastDVMRPAdminMode 1.3.6.1.4.1.248.12.4.6.1
This enables or disables DVMRP on the system.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2AgentMulticastDVMRPRouteExpiryTime 1.3.6.1.4.1.248.12.4.6.248
TBD.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..200  

hm2AgentSnmpTrapFlagsConfigGroupMulticast 1.3.6.1.4.1.248.12.4.7
OBJECT IDENTIFIER    

hm2AgentSnmpDVMRPTrapFlag 1.3.6.1.4.1.248.12.4.7.1
This enables or disables DVMRP Traps on the system.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2AgentSnmpPIMTrapFlag 1.3.6.1.4.1.248.12.4.7.2
This enables or disables PIM Traps on the system.
Status: current Access: read-write
OBJECT-TYPE    
  HmEnabledStatus  

hm2AgentIpStaticMRouteTable 1.3.6.1.4.1.248.12.4.8
The table listing the Static Multicast Route Entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2AgentIpStaticMRouteEntry

hm2AgentIpStaticMRouteEntry 1.3.6.1.4.1.248.12.4.8.1
Information about a table entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2AgentIpStaticMRouteEntry  

hm2AgentIpStaticMRouteSrcAddressType 1.3.6.1.4.1.248.12.4.8.1.1
The address type of this Multicast data source.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddressType  

hm2AgentIpStaticMRouteSrcIpAddr 1.3.6.1.4.1.248.12.4.8.1.2
The address of the Multicast data source.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddress Size(4|16)  

hm2AgentIpStaticMRouteSrcNetMask 1.3.6.1.4.1.248.12.4.8.1.3
The network mask for the IP address of the Multicast data source.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..128  

hm2AgentIpStaticMRouteRpfIpAddr 1.3.6.1.4.1.248.12.4.8.1.4
The RPF Address. This object has been deprecated, because it has no address type. It is replaced by hm2AgentIpStaticMRouteExtRpfIpAddr.
Status: deprecated Access: read-create
OBJECT-TYPE    
  InetAddress  

hm2AgentIpStaticMRouteIfIndex 1.3.6.1.4.1.248.12.4.8.1.5
The interface index is valid only for IPv6 and only if RPF address is link-local.
Status: current Access: read-create
OBJECT-TYPE    
  InterfaceIndex  

hm2AgentIpStaticMRoutePreference 1.3.6.1.4.1.248.12.4.8.1.6
The preference of this route entry.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..255  

hm2AgentIpStaticMRouteStatus 1.3.6.1.4.1.248.12.4.8.1.7
The status of this row. The status object cannot be set to active(1) before a valid value has been written to hm2AgentIpStaticMRouteExtRpfIpAddr. All writeable objects in this entry can be modified when the status of this entry is active(1).
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

hm2AgentIpStaticMRouteExtRpfIpAddrType 1.3.6.1.4.1.248.12.4.8.1.248
The address type of the RPF Address.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressType  

hm2AgentIpStaticMRouteExtRpfIpAddr 1.3.6.1.4.1.248.12.4.8.1.249
The RPF Address.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddress  

hm2AgentPIMBsrCandidateConfTable 1.3.6.1.4.1.248.12.4.3.4
Provides Candidate-BSR-Advertisements interval information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2AgentPIMBsrCandidateConfEntry

hm2AgentPIMBsrCandidateConfEntry 1.3.6.1.4.1.248.12.4.3.4.1
Information about a table entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2AgentPIMBsrCandidateConfEntry  

pimBsrCandidateBSRAdvInterval 1.3.6.1.4.1.248.12.4.3.4.1.1
A Candidate BSR generates Candidate-BSR-Advertisements periodically. This object represents the time interval in seconds between two consecutive advertisements.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..16383  

hm2AgentMulticastMgmdExtConfigGroup 1.3.6.1.4.1.248.12.4.250
OBJECT IDENTIFIER    

hm2AgentMulticastMgmdExtTable 1.3.6.1.4.1.248.12.4.250.10
The (conceptual) table listing the upstream interface of the router. This is also known as proxy interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2AgentMulticastMgmdExtEntry

hm2AgentMulticastMgmdExtEntry 1.3.6.1.4.1.248.12.4.250.10.1
An entry (conceptual row) representing the upstream interface of the router.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2AgentMulticastMgmdExtEntry  

hm2AgentMulticastMgmdUnsolicitRprtInterval 1.3.6.1.4.1.248.12.4.250.10.1.1
Specify how often the system should send unsolicited reports to routers on the upstream interface.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..260  

hm2AgentMulticastMgmdNumberOfGroups 1.3.6.1.4.1.248.12.4.250.10.1.2
Number of groups corresponding to the proxy interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

hm2AgentMulticastMgmdHostCacheExtGroup 1.3.6.1.4.1.248.12.4.251
OBJECT IDENTIFIER    

hm2AgentMulticastMgmdHostCacheExtTable 1.3.6.1.4.1.248.12.4.251.10
The (conceptual) table listing group addresses of the upstream interface of the router.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Hm2AgentMulticastMgmdHostCacheExtEntry

hm2AgentMulticastMgmdHostCacheExtEntry 1.3.6.1.4.1.248.12.4.251.10.1
An entry (conceptual row) representing a group of upstream interface of the router.
Status: current Access: not-accessible
OBJECT-TYPE    
  Hm2AgentMulticastMgmdHostCacheExtEntry  

hm2AgentMulticastMgmdHostStatus 1.3.6.1.4.1.248.12.4.251.10.1.1
A variable that describes the state of the host in relation with an IP multicast group.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER non-member(1), delay-member(2), idle-member(3)  

hm2AgentMulticastSNMPExtensionGroup 1.3.6.1.4.1.248.12.4.260
OBJECT IDENTIFIER    

hm2AgentMulticastProtocolEnableErrorReturn 1.3.6.1.4.1.248.12.4.260.1
Cannot enable protocol x because protocol y is enabled.
Status: current Access: read-only
OBJECT-IDENTITY    

hm2AgentMulticastNullGroupErrorReturn 1.3.6.1.4.1.248.12.4.260.2
The group address or the group address mask is zero.
Status: current Access: read-only
OBJECT-IDENTITY    

hm2AgentMulticastBoundaryRangeEntriesErrorReturn 1.3.6.1.4.1.248.12.4.260.3
The group address is out of administratively scoped addresses range(239.x.x.x).
Status: current Access: read-only
OBJECT-IDENTITY    

hm2AgentMulticastHostEntriesErrorReturn 1.3.6.1.4.1.248.12.4.260.4
The group address has host bits set.
Status: current Access: read-only
OBJECT-IDENTITY    

hm2AgentMgmdHostInvalidEntryErrorReturn 1.3.6.1.4.1.248.12.4.260.5
The entry cannot be deleted because is not valid.
Status: current Access: read-only
OBJECT-IDENTITY    

hm2AgentMulticastProtocolDeInitErrorReturn 1.3.6.1.4.1.248.12.4.260.6
The multicast routing protocol is deinitializing. Please retry later.
Status: current Access: read-only
OBJECT-IDENTITY    

hm2AgentMulticastLocalAddressErrorReturn 1.3.6.1.4.1.248.12.4.260.7
The IP address is not local.
Status: current Access: read-only
OBJECT-IDENTITY    

hm2AgentMulticastCandRPErrorReturn 1.3.6.1.4.1.248.12.4.260.8
Candidate RP is already configured on another interface.
Status: current Access: read-only
OBJECT-IDENTITY    

hm2AgentMulticastUnicastValidationErrorReturn 1.3.6.1.4.1.248.12.4.260.9
The IP address is out of unicast range.
Status: current Access: read-only
OBJECT-IDENTITY    

hm2AgentMulticastGroupValidationErrorReturn 1.3.6.1.4.1.248.12.4.260.10
The group address is out of multicast range.
Status: current Access: read-only
OBJECT-IDENTITY    

hm2AgentMulticastSSMValidationErrorReturn 1.3.6.1.4.1.248.12.4.260.11
The group address is in SSM range.
Status: current Access: read-only
OBJECT-IDENTITY    

hm2AgentMulticastStaticSourceErrorReturn 1.3.6.1.4.1.248.12.4.260.12
Source address is a directly connected address.
Status: current Access: read-only
OBJECT-IDENTITY    

hm2AgentMulticastStaticRPFErrorReturn 1.3.6.1.4.1.248.12.4.260.13
The RPF address is a local address.
Status: current Access: read-only
OBJECT-IDENTITY    

hm2AgentMulticastStaticHostErrorReturn 1.3.6.1.4.1.248.12.4.260.14
The source IP address has the host bit set.
Status: current Access: read-only
OBJECT-IDENTITY    

hm2AgentMulticastCandRPPrimaryErrorReturn 1.3.6.1.4.1.248.12.4.260.15
The candidate RP address must be a primary IP address.
Status: current Access: read-only
OBJECT-IDENTITY    

hm2AgentMulticastCandBSRPrimaryErrorReturn 1.3.6.1.4.1.248.12.4.260.16
The candidate BSR address must be a primary IP address.
Status: current Access: read-only
OBJECT-IDENTITY    

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor