HM2-L2REDUNDANCY-MIB

File: HM2-L2REDUNDANCY-MIB.mib (71572 bytes)

Imported modules

SNMPv2-SMI	SNMPv2-CONF	SNMP-FRAMEWORK-MIB
SNMPv2-TC	IF-MIB	HM2-TC-MIB
INET-ADDRESS-MIB

Imported symbols

MODULE-IDENTITY	OBJECT-TYPE	OBJECT-IDENTITY
NOTIFICATION-TYPE	Integer32	Unsigned32
Counter32	MODULE-COMPLIANCE	NOTIFICATION-GROUP
OBJECT-GROUP	SnmpAdminString	RowStatus
MacAddress	TEXTUAL-CONVENTION	InterfaceIndexOrZero
HmEnabledStatus	hm2ConfigurationMibs	InetAddressType
InetAddress

Defined Types

Hm2CplPortOpState
.
TEXTUAL-CONVENTION
	INTEGER	not-connected(1), active(2), standby(3), not-applicable(4)

Hm2MrpEntry
SEQUENCE
	hm2MrpDomainID	OCTET STRING
	hm2MrpDomainName	SnmpAdminString
	hm2MrpRingport1GroupID	Integer32
	hm2MrpRingport1IfIndex	Integer32
	hm2MrpRingport1OperState	INTEGER
	hm2MrpRingport2GroupID	Integer32
	hm2MrpRingport2IfIndex	Integer32
	hm2MrpRingport2OperState	INTEGER
	hm2MrpRoleAdminState	INTEGER
	hm2MrpRoleOperState	INTEGER
	hm2MrpRecoveryDelay	INTEGER
	hm2MrpRecoveryDelaySupported	INTEGER
	hm2MrpVlanID	Integer32
	hm2MrpMRMPriority	Integer32
	hm2MrpMRMReactOnLinkChange	INTEGER
	hm2MrpMRMRingOpenCount	Counter32
	hm2MrpMRMLastRingOpenChange	Unsigned32
	hm2MrpMRMRoundTripDelayMax	Unsigned32
	hm2MrpMRMRoundTripDelayMin	Unsigned32
	hm2MrpMRMRoundTripDelayReset	INTEGER
	hm2MrpMRMNonBlockingMRCSupported	INTEGER
	hm2MrpMRCBlockedSupported	INTEGER
	hm2MrpRingOperState	INTEGER
	hm2MrpRedundancyOperState	INTEGER
	hm2MrpConfigOperState	INTEGER
	hm2MrpRowStatus	RowStatus
	hm2MrpRingport2FixedBackup	HmEnabledStatus

Hm2SrmEntry
SEQUENCE
	hm2SrmRingID	Integer32
	hm2SrmAdminState	INTEGER
	hm2SrmOperState	INTEGER
	hm2SrmVlanID	Integer32
	hm2SrmMRPDomainID	OCTET STRING
	hm2SrmPartnerMAC	MacAddress
	hm2SrmSubRingProtocol	INTEGER
	hm2SrmSubRingName	SnmpAdminString
	hm2SrmSubRingPortIfIndex	Integer32
	hm2SrmSubRingPortOperState	INTEGER
	hm2SrmSubRingOperState	INTEGER
	hm2SrmRedundancyOperState	INTEGER
	hm2SrmConfigOperState	INTEGER
	hm2SrmRowStatus	RowStatus

Hm2RingCouplingEntry
SEQUENCE
	hm2RingCplInterconnIfIndex	InterfaceIndexOrZero
	hm2RingCplInterconnIfOpState	INTEGER
	hm2RingCplControlIfIndex	InterfaceIndexOrZero
	hm2RingCplControlIfOpState	INTEGER
	hm2RingCplPartnerInterconnIfIndex	InterfaceIndexOrZero
	hm2RingCplPartnerInterconnIfOpState	INTEGER
	hm2RingCplPartnerIpAddrType	InetAddressType
	hm2RingCplPartnerIpAddr	InetAddress
	hm2RingCplCouplingMode	INTEGER
	hm2RingCplControlModeOperState	INTEGER
	hm2RingCplModeOperState	INTEGER
	hm2RingCplOperState	INTEGER
	hm2RingCplConfigOperState	INTEGER
	hm2RingCplCouplingLinks	INTEGER
	hm2RingCplExtendedDiag	INTEGER
	hm2RingCplNetCoupling	INTEGER
	hm2RingCplRedOperState	INTEGER
	hm2RingCplRowStatus	RowStatus

Defined Values

hm2L2RedundancyMib		1.3.6.1.4.1.248.11.40
Hirschmann Layer 2 Redundancy MIB. Copyright (C) 2011. All Rights Reserved.
MODULE-IDENTITY

hm2L2RedundancyMibNotifications		1.3.6.1.4.1.248.11.40.0
OBJECT IDENTIFIER

hm2L2RedundancyMibObjects		1.3.6.1.4.1.248.11.40.1
OBJECT IDENTIFIER

hm2L2RedundancyMibSNMPExtensionGroup		1.3.6.1.4.1.248.11.40.3
OBJECT IDENTIFIER

hm2MrpMibGroup		1.3.6.1.4.1.248.11.40.1.1
OBJECT IDENTIFIER

hm2SrmMibGroup		1.3.6.1.4.1.248.11.40.1.4
OBJECT IDENTIFIER

hm2RingRedMibGroup		1.3.6.1.4.1.248.11.40.1.7
OBJECT IDENTIFIER

hm2RingCouplingMibGroup		1.3.6.1.4.1.248.11.40.1.8
OBJECT IDENTIFIER

hm2RedundantCplConfigMibGroup		1.3.6.1.4.1.248.11.40.1.9
OBJECT IDENTIFIER

hm2MrpTable		1.3.6.1.4.1.248.11.40.1.1.1
Every entry in this table contains information about a Media Redundancy Protocol (MRP) domain, defined by IEC 62439-2.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hm2MrpEntry

hm2MrpEntry		1.3.6.1.4.1.248.11.40.1.1.1.1
An entry in the hm2MrpTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hm2MrpEntry

hm2MrpDomainID		1.3.6.1.4.1.248.11.40.1.1.1.1.1
Universally unique identifier belongs to the MRP domain which represents a ring.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	OCTET STRING	Size(16)

hm2MrpDomainName		1.3.6.1.4.1.248.11.40.1.1.1.1.2
A logical name for the MRP domain to ease the management of MRP domains.
Status: current	Access: read-create
OBJECT-TYPE
	SnmpAdminString

hm2MrpRingport1GroupID		1.3.6.1.4.1.248.11.40.1.1.1.1.3
Unique index to identify the slot number of the ringport 1 in the MRP domain.
Status: obsolete	Access: read-create
OBJECT-TYPE
	Integer32

hm2MrpRingport1IfIndex		1.3.6.1.4.1.248.11.40.1.1.1.1.4
Interface index of the ringport 1 in the MRP domain.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

hm2MrpRingport1OperState		1.3.6.1.4.1.248.11.40.1.1.1.1.5
Operational state of ringport 1. disabled(1) indicates that all frames are dropped. blocked(2) indicates that all frames are dropped except - MRP topology change frames and MRP test frames from a MRM, - MRP link change frames from a MRC, - frames from other protocols that also define to pass blocked(2) ports. forwarding(3) indicates that all frames are passed through according to the forwarding behavior of IEEE 802.1D. notConnected(4) indicates that the port has no link.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	disabled(1), blocked(2), forwarding(3), notConnected(4)

hm2MrpRingport2GroupID		1.3.6.1.4.1.248.11.40.1.1.1.1.6
Unique index to identify the slot number of the ringport 2 in the MRP domain.
Status: obsolete	Access: read-create
OBJECT-TYPE
	Integer32

hm2MrpRingport2IfIndex		1.3.6.1.4.1.248.11.40.1.1.1.1.7
Interface index of the ringport 2 in the MRP domain.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

hm2MrpRingport2OperState		1.3.6.1.4.1.248.11.40.1.1.1.1.8
Operational state of ringport 2. disabled(1) indicates that all frames are dropped. blocked(2) indicates that all frames are dropped except - MRP topology change frames and MRP test frames from a MRM, - MRP link change frames from a MRC, - frames from other protocols that also define to pass blocked(2) ports. forwarding(3) indicates that all frames are passed through according to the forwarding behavior of IEEE 802.1D. notConnected(4) indicates that the port has no link.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	disabled(1), blocked(2), forwarding(3), notConnected(4)

hm2MrpRoleAdminState		1.3.6.1.4.1.248.11.40.1.1.1.1.9
Control the role of the MRP entity in the MRP domain. If the value is set to client(1) the entity will be in the role of a Media Redundancy Client (MRC). If the value is set to manager(2) the entity will be in the role of a Media Redundancy Manager (MRM).
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	client(1), manager(2)

hm2MrpRoleOperState		1.3.6.1.4.1.248.11.40.1.1.1.1.10
Operational role of the MRP entity in the MRP domain. client(1) indicates that the MRP entity is in a MRC role. manager(2) indicates that the MRP entity is the manager MRM of this MRP domain. undefined(3) indicates that the MRP entity doesn't work.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	client(1), manager(2), undefined(3)

hm2MrpRecoveryDelay		1.3.6.1.4.1.248.11.40.1.1.1.1.11
The MRM defines with its parameter set the maximum recovery delay of the ring recovery in the MRP domain. delay500(1) specifies the parameter set for the maximum recovery delay of 500ms in the MRP domain. delay200(2) specifies the parameter set for the maximum recovery delay of 200ms in the MRP domain. delay30(3) specifies the parameter set for the maximum recovery delay of 30ms in the MRP domain. delay10(4) specifies the parameter set for the maximum recovery delay of 10ms in the MRP domain.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	delay500(1), delay200(2), delay30(3), delay10(4)

hm2MrpRecoveryDelaySupported		1.3.6.1.4.1.248.11.40.1.1.1.1.12
The 10ms and 30ms recovery time put additional restrictions on the cable length and on the reaction time of each client in the MRP ring, so these recovery times may not be supported by a MRP entity. supportedAll(1) indicates that all recovery times in hm2MrpRecoveryDelay are supported by the MRP entity. supported200500(2) indicates that only the recovery times 500ms and 200ms are supported by the MRP entity.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	supportedAll(1), supported200500(2)

hm2MrpVlanID		1.3.6.1.4.1.248.11.40.1.1.1.1.13
VLAN identifier assigned to the MRP domain. If value is set to 0 no VLAN is assigned.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

hm2MrpMRMPriority		1.3.6.1.4.1.248.11.40.1.1.1.1.14
Priority of the MRM. A lower value indicates a higher priority.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..65535

hm2MrpMRMReactOnLinkChange		1.3.6.1.4.1.248.11.40.1.1.1.1.15
Specifies whether the MRM reacts on all MRP link change frames or not. enabled(1) indicates that the MRM reacts on all MRP link change frames. disabled(2) indicates that the MRM does not react on link down MRP link change frames.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

hm2MrpMRMRingOpenCount		1.3.6.1.4.1.248.11.40.1.1.1.1.16
Counter will be incremented when the ring state changes to ring open.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

hm2MrpMRMLastRingOpenChange		1.3.6.1.4.1.248.11.40.1.1.1.1.17
The local time at which the ring state last changed to ring open. Measured in seconds since 00:00:00, January 1, 1970.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hm2MrpMRMRoundTripDelayMax		1.3.6.1.4.1.248.11.40.1.1.1.1.18
The max. Round-Trip-Delay (in microseconds) which was measured by the MRM since startup or reset. A device which supports only the recovery delays 200ms and 500ms doesn't support the measuring of round-trip-delay.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hm2MrpMRMRoundTripDelayMin		1.3.6.1.4.1.248.11.40.1.1.1.1.19
The min. Round-Trip-Delay (in microseconds) which was measured by the MRM since startup or reset. A device which supports only the recovery delays 200ms and 500ms doesn't support the measuring of round-trip-delay.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

hm2MrpMRMRoundTripDelayReset		1.3.6.1.4.1.248.11.40.1.1.1.1.20
A write request with reset(1) will reset the values of hm2MrpMRMRoundTripDelayMax and hm2MrpMRMRoundTripDelayMin to zero at the same time.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	reset(1)

hm2MrpMRMNonBlockingMRCSupported		1.3.6.1.4.1.248.11.40.1.1.1.1.21
Ability of the MRM to support MRC in the ring which have hm2MrpMRCBlockedSupported set disabled. enabled(1) indicates that the MRM is able to support MRC in the ring which have hm2MrpMRCBlockedSupported set disabled. disabled(2) indicates that the MRM is not able to support MRC in the ring which have hm2MrpMRCBlockedSupported set disabled.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

hm2MrpMRCBlockedSupported		1.3.6.1.4.1.248.11.40.1.1.1.1.22
Ability of the MRC to receive and forward MRP test frames, MRP link change frames and MRP topology change frames at a ringport whose port state is blocked. enabled(1) indicates that the MRC is able to receive and forward these MRP frames at a ringport whose port state is blocked. disabled(2) indicates that the MRC is not able to receive and forward these MRP frames at a ringport whose port state is blocked.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

hm2MrpRingOperState		1.3.6.1.4.1.248.11.40.1.1.1.1.23
Actual ring state of the MRP redundancy domain. The ring state can only be detected by the MRM. open(1) indicates that the ring is open. closed(2) indicates that the ring is closed. undefined(3) indicates an undefined ring state or is read if hm2MrpRoleOperState indicates the value client.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	open(1), closed(2), undefined(3)

hm2MrpRedundancyOperState		1.3.6.1.4.1.248.11.40.1.1.1.1.24
Operational state of ring redundancy in the MRP domain. available(1) indicates that ring redundancy exists in the MRP domain. notAvailable(2) indicates that ring redundancy does not exist in the MRP domain.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	available(1), notAvailable(2)

hm2MrpConfigOperState		1.3.6.1.4.1.248.11.40.1.1.1.1.25
Operational state of the configuration in the MRP domain. noError(1) indicates that no configuration error was detected. ringportLinkError(2) indicates that one of the ring lines is not connected with one of the ring ports in the MRP domain. multipleMRM(3) indicates multiple active MRM in the ring. singleSideReceive(4) indicates that the MRM has seen it's test frames, but only on one ring port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	noError(1), ringportLinkError(2), multipleMRM(3), singleSideReceive(4)

hm2MrpRowStatus		1.3.6.1.4.1.248.11.40.1.1.1.1.26
Supports creation, deletion and activation of rows. A row must not be active(1) in order to be modified. A row can be taken out of service by writing the value notInService(2).
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

hm2MrpRingport2FixedBackup		1.3.6.1.4.1.248.11.40.1.1.1.1.27
If value is set to enable(1) the ringport 2 at the MRM will always be the backup port. Setting is only relevant if hm2MrpRoleAdminState is set to manager(2).
Status: current	Access: read-create
OBJECT-TYPE
	HmEnabledStatus

hm2MrpConformance		1.3.6.1.4.1.248.11.40.1.1.2
OBJECT IDENTIFIER

hm2MrpCompliances		1.3.6.1.4.1.248.11.40.1.1.2.1
OBJECT IDENTIFIER

hm2MrpCompliance		1.3.6.1.4.1.248.11.40.1.1.2.1.1
Basic implementation requirements for MRP support. The agent shall support the monitoring and control of MRP redundancy domains.
Status: current	Access: read-create
MODULE-COMPLIANCE

hm2MrpGroups		1.3.6.1.4.1.248.11.40.1.1.2.2
OBJECT IDENTIFIER

hm2MrpDomainBasicGroup		1.3.6.1.4.1.248.11.40.1.1.2.2.1
Parameters which are necessary to monitor and control the status of MRP domains.
Status: current	Access: read-create
OBJECT-GROUP

hm2MrpDomainManagerGroup		1.3.6.1.4.1.248.11.40.1.1.2.2.2
Additional parameters which are necessary to monitor and control the status of a MRM.
Status: current	Access: read-create
OBJECT-GROUP

hm2MrpDomainDiagGroup		1.3.6.1.4.1.248.11.40.1.1.2.2.3
Parameters which are optional to monitor and control the diagnostic status of MRP domains.
Status: current	Access: read-create
OBJECT-GROUP

hm2MrpNotificationsGroup		1.3.6.1.4.1.248.11.40.1.1.2.2.4
Notifications indicate changes in the MRP ring.
Status: current	Access: read-create
NOTIFICATION-GROUP

hm2MrpFastMrp		1.3.6.1.4.1.248.11.40.1.1.3
Fast MRP means that MRP supports also maximum recovery times of 30ms or 10ms as defined in IEC 62439-2. supported(1) indicates that the device is able to support fast recovery times for MRP like 30ms or 10ms. notSupported(2) indicates that only the MRP recovery times 500ms and 200ms are supported by the device.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	supported(1), notSupported(2)

hm2SrmGlobalAdminState		1.3.6.1.4.1.248.11.40.1.4.1
Enables or disables the global SRM admin mode.
Status: current	Access: read-write
OBJECT-TYPE
	HmEnabledStatus

hm2SrmMaxInstances		1.3.6.1.4.1.248.11.40.1.4.2
Maximum number of supported SRM instances in the hm2SrmTable.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

hm2SrmTable		1.3.6.1.4.1.248.11.40.1.4.3
Every entry in this table contains information about a Sub-Ring Manager (SRM) domain.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hm2SrmEntry

hm2SrmEntry		1.3.6.1.4.1.248.11.40.1.4.3.1
Information about a Sub-Ring Manager (SRM) domain.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hm2SrmEntry

hm2SrmRingID		1.3.6.1.4.1.248.11.40.1.4.3.1.1
Identifier of the sub-ring in the SRM domain.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

hm2SrmAdminState		1.3.6.1.4.1.248.11.40.1.4.3.1.2
Admin state of the entity in the SRM domain. If the value is set to manager(1) the entity will be in the role of a Sub-Ring Manager. If the value is set to redundantManager(2) the entity will be in the role of the Sub-Ring Manager which will block its ringport if the sub-ring is closed. If the value is set to singleManager(3) the entity will be in the role of the single-manager which has both ends of a sub-ring connected and will block one of these ends if the sub-ring is closed. Note: Two instances in the hm2SrmTable are needed to build a single-manager where both instances must have singleManager(3) selected. Note: The sub-ring has two managers at the same time. The redundant manager can be designated.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	manager(1), redundantManager(2), singleManager(3)

hm2SrmOperState		1.3.6.1.4.1.248.11.40.1.4.3.1.3
Operational state of the entity in the SRM domain. manager(1) indicates that the entity is in the role of a Sub-Ring Manager. redundantManager(2) indicates that the entity is in the role of the Sub-Ring Manager which will block its ringport if the sub-ring is closed. singleManager(3) indicates that the entity is in the role of the single manager. disabled(4) indicates that the protocol does not work on the entity.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	manager(1), redundantManager(2), singleManager(3), disabled(4)

hm2SrmVlanID		1.3.6.1.4.1.248.11.40.1.4.3.1.4
VLAN identifier of the SRM domain. If value is set to 0 no VLAN is assigned.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..4042

hm2SrmMRPDomainID		1.3.6.1.4.1.248.11.40.1.4.3.1.5
Only for MRP: Universally unique identifier belongs to the MRP domain which represents a sub- ring.
Status: current	Access: read-create
OBJECT-TYPE
	OCTET STRING	Size(16)

hm2SrmPartnerMAC		1.3.6.1.4.1.248.11.40.1.4.3.1.6
The MAC address of the partner Sub-Ring Manager in the same sub-ring domain.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

hm2SrmSubRingProtocol		1.3.6.1.4.1.248.11.40.1.4.3.1.7
If the value is set to iec-62439-mrp(4) the Entity will run the MRP protocol. Note: If using iec-62439-mrp(4) all clients in The sub-ring segment must run MRP according To IEC 62439.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	iec-62439-mrp(4)

hm2SrmSubRingName		1.3.6.1.4.1.248.11.40.1.4.3.1.8
Name of the sub-ring in the SRM domain.
Status: current	Access: read-create
OBJECT-TYPE
	SnmpAdminString

hm2SrmSubRingPortIfIndex		1.3.6.1.4.1.248.11.40.1.4.3.1.9
Interface index of sub-ring port in the SRM domain.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

hm2SrmSubRingPortOperState		1.3.6.1.4.1.248.11.40.1.4.3.1.10
Operational state of sub-ring port. disabled(1) indicates that all frames are dropped. blocked(2) indicates that all frames are dropped except - frames used by the selected ring protocol which are defined to pass blocked(2) ports, - frames from other protocols which are Defined to pass blocked(2) ports. forwarding(3) indicates that all frames are passed through according to the forwarding behavior of IEEE 802.1D. not-connected(4) indicates that the port has no link.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	disabled(1), blocked(2), forwarding(3), not-connected(4)

hm2SrmSubRingOperState		1.3.6.1.4.1.248.11.40.1.4.3.1.11
Operational state of the sub-ring in the SRM domain. undefined(1) indicates an undefined sub-ring state. open(2) indicates that the sub-ring is opened. closed(3) indicates that the sub-ring is closed.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	undefined(1), open(2), closed(3)

hm2SrmRedundancyOperState		1.3.6.1.4.1.248.11.40.1.4.3.1.12
Operational state of the ring redundancy in The SRM domain. redGuaranteed(1) indicates that ring redundancy is guaranteed in the SRM domain. redNotGuaranteed(2) indicates that ring redundancy is not guaranteed in the SRM domain.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	redGuaranteed(1), redNotGuaranteed(2)

hm2SrmConfigOperState		1.3.6.1.4.1.248.11.40.1.4.3.1.13
Operational state of the configuration in the SRM domain. noError(1) indicates that no configuration error was detected. ringPortLinkError(2) indicates that the ring port has no link or one of the sub- ring lines is not connected with one of the ring ports of the entity but to another port of the entity. multipleSRM(3) indicates that the Sub-Ring Manager receives frames from more than one Sub-Ring Managers in the sub-ring. noPartnerManager(4) indicates that the Sub-Ring Manager receives his own frames. concurrentVLAN(5) indicates that the VLAN of the SRM domain is used by MRP in the basis ring. concurrentPort(6) indicates that the ringport of the SRM domain is used by another redundancy protocol. concurrentRedundancy(7) indicates the SRM domain is not active because of another active redundancy protocol. trunkMember(8) indicates that the ringport of the SRM domain is member of a trunk. sharedVLAN(9) indicates the SRM domain cannot be active because Shared VLAN is active and MRP is used in the basis ring too.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	noError(1), ringPortLinkError(2), multipleSRM(3), noPartnerManager(4), concurrentVLAN(5), concurrentPort(6), concurrentRedundancy(7), trunkMember(8), sharedVLAN(9)

hm2SrmRowStatus		1.3.6.1.4.1.248.11.40.1.4.3.1.20
Defines the status of the SRM database entry.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

hm2RingRedAdminState		1.3.6.1.4.1.248.11.40.1.7.1
Enables or disables the global (HIPER)Ring Redundancy admin mode.
Status: current	Access: read-write
OBJECT-TYPE
	HmEnabledStatus

hm2RingRedMode		1.3.6.1.4.1.248.11.40.1.7.2
The mode (HIPER)Ring Redundancy is configured.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ring-switch(1)

hm2RingRedPrimaryIntf		1.3.6.1.4.1.248.11.40.1.7.3
Interface index of the primary interface.
Status: current	Access: read-write
OBJECT-TYPE
	InterfaceIndexOrZero

hm2RingRedPrimaryIntfState		1.3.6.1.4.1.248.11.40.1.7.4
Operational state of the primary ring port. The port states are as follows, active - port is logically up and active. inactive - port is logically down. not-available - no Hiper Ring instance is running, check prerequisites.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	not-available(1), active(2), inactive(3)

hm2RingRedSecondaryIntf		1.3.6.1.4.1.248.11.40.1.7.5
Interface index of the secondary interface.
Status: current	Access: read-write
OBJECT-TYPE
	InterfaceIndexOrZero

hm2RingRedSecondaryIntfState		1.3.6.1.4.1.248.11.40.1.7.6
Operational state of the secondary ring port. The port states are as follows, active - port is logically up and active. inactive - port is logically down. not-available - no Hiper Ring instance is running, check prerequisites.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	not-available(1), active(2), inactive(3)

hm2RingCouplingTable		1.3.6.1.4.1.248.11.40.1.8.1
This table contains variables to define an entry in the ring coupling database.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		Hm2RingCouplingEntry

hm2RingCouplingEntry		1.3.6.1.4.1.248.11.40.1.8.1.1
The entry of the hm2RingCouplingTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	Hm2RingCouplingEntry

hm2RingCplInterconnIfIndex		1.3.6.1.4.1.248.11.40.1.8.1.1.1
Interface index of the coupling link. Note that only those ports can be chosen which do not belong to another L2 redundancy mechanism like ring redundancy or dual homing and that row creation is only done by writing to hm2RingCplRowStatus.
Status: current	Access: read-write
OBJECT-TYPE
	InterfaceIndexOrZero

hm2RingCplInterconnIfOpState		1.3.6.1.4.1.248.11.40.1.8.1.1.2
Operational state of the coupling interface. active(2) indicates that the port is switching. standby(3) indicates that the port is in standby mode. On the slave active(2) indicates that a ring coupling failure has occured and the port is switching. On the slave standby(3) indicates that the ring coupling is ok and the slave is in standby mode.
Status: current	Access: read-only
OBJECT-TYPE
	Hm2CplPortOpState

hm2RingCplControlIfIndex		1.3.6.1.4.1.248.11.40.1.8.1.1.3
Interface index of the control link in case of outband-control. Note that only those ports can be chosen which do not belong to another L2 redundancy mechanism like ring redundancy or dual homing and that row creation is only done by writing to hm2RingCplRowStatus.
Status: current	Access: read-write
OBJECT-TYPE
	InterfaceIndexOrZero

hm2RingCplControlIfOpState		1.3.6.1.4.1.248.11.40.1.8.1.1.4
Operational state of the control interface in case of outband-control.
Status: current	Access: read-only
OBJECT-TYPE
	Hm2CplPortOpState

hm2RingCplPartnerInterconnIfIndex		1.3.6.1.4.1.248.11.40.1.8.1.1.5
Interface index identifies the coupling link of the partner in the ring coupling. This variable can only be set if the hm2RingCplControlMode is local(4).
Status: current	Access: read-write
OBJECT-TYPE
	InterfaceIndexOrZero

hm2RingCplPartnerInterconnIfOpState		1.3.6.1.4.1.248.11.40.1.8.1.1.6
Operational state of the coupling interface of the partner in the ring coupling. active(2) indicates that the partner port is switching. standby(3) indicates that the partner port is in standby mode.
Status: current	Access: read-only
OBJECT-TYPE
	Hm2CplPortOpState

hm2RingCplPartnerIpAddrType		1.3.6.1.4.1.248.11.40.1.8.1.1.7
Partner IP Address type.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddressType

hm2RingCplPartnerIpAddr		1.3.6.1.4.1.248.11.40.1.8.1.1.8
IP Address of the partner in the ring coupling.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddress

hm2RingCplCouplingMode		1.3.6.1.4.1.248.11.40.1.8.1.1.9
Ring-coupling operating mode . In single(1) mode both coupling ports are local to the switch, switch performs master and slave functions. In dual-master-inband(2) mode second coupling port is on a remote switch, local switch is master, communication over network. In dual-master-outband(3) mode second coupling port is on a remote switch, local switch is master, communication over dedicated control port. In dual-slave-inband(4) mode second coupling port is on a remote switch, local switch is slave, communication over network. In dual-slave-outband(5) mode second coupling port is on a remote switch, local switch is slave, communication over dedicated control port. unknown(6) cannot be set,it's returned when no mode is configured.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	single(1), dual-master-inband(2), dual-master-outband(3), dual-slave-inband(4), dual-slave-outband(5), unknown(6)

hm2RingCplControlModeOperState		1.3.6.1.4.1.248.11.40.1.8.1.1.10
Control mode of the ring coupling which can only be chosen by the slave, the master just reports his current control mode. unknown(3) cannot be set. In outband(1) mode an additional line must connect the control interfaces between the two partners in the ring coupling. In inband(2) mode only the coupling link port is needed. In local(4) mode the coupling link port and the partner port are located on the same switch.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	outband(1), inband(2), unknown(3), local(4)

hm2RingCplModeOperState		1.3.6.1.4.1.248.11.40.1.8.1.1.11
Mode of operation . slaveOn(2) slave is activated. slaveOff(1) slave is deactivated, the ring coupling is disabled and the switch acts from now in normal rs mode.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	slaveOff(1), slaveOn(2)

hm2RingCplOperState		1.3.6.1.4.1.248.11.40.1.8.1.1.12
Operational state of an entry. If a new entry is created by setting hm2RingCplRowStatus to create(1), the operState returns a value of underCreation(1). slave(2) indicates that switch is configured to be the slave of the ring coupling, that means the switch is in standby mode. master(3) indicates that a switch is configured to be the master of the ring coupling. local(4) indicates that the switch is configured to control a ring coupling where the coupling port and the partner port are located on the same switch.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	underCreation(1), slave(2), master(3), local(4)

hm2RingCplConfigOperState		1.3.6.1.4.1.248.11.40.1.8.1.1.13
Operational state of the ring coupling configuration. slaveCouplingLinkError(2) indicates that the coupling link is not connected with the coupling port of the slave but with another port of the slave. In case of outband control additional failures can be detected: slaveControlLinkError(3) indicates that the control port of the slave has either no link or the link fails. masterControlLinkError(4) indicates that the control link is not connected with the control port of the master but with another port of the master. twoSlaves(5) is returned when two slaves are connected by the control line. localPartnerLinkError(6) indicates that the partner coupling link is not connected with the partner port of the slave but with another port of the slave in local control mode. localInvalidCouplingPort(7) indicates that in local mode the coupling line is connected to another switch and not on the same switch like the partner line. couplingPortNotAvailable(8), controlPortNotAvailable(9) and partnerPortNotAvailable(10) indicate that this port is not available because the module related to this port is not available or the port does not exist on this module.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	noError(1), slaveCouplingLinkError(2), slaveControlLinkError(3), masterControlLinkError(4), twoSlaves(5), localPartnerLinkError(6), localInvalidCouplingPort(7), couplingPortNotAvailable(8), controlPortNotAvailable(9), partnerPortNotAvailable(10)

hm2RingCplCouplingLinks		1.3.6.1.4.1.248.11.40.1.8.1.1.14
Maximum coupling links between two coupled rings in case of a failure in one of the coupled rings. If there is no connection starting from the switch in slave or local operational state over the route of the coupled rings or nets to oneself the slave or the local mode want to set the coupling port in forwarding after a timeout period. basicRedundancy(1) prevents the slave or the local mode from setting its coupling port into forwarding in case of the described failure. In this case the segment which is connected to this coupling port is unreachable until the failure is eliminated. In extendedRedundancy(2) the coupling port and the partner coupling port are allowed to be in forwarding.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	basicRedundancy(1), extendedRedundancy(2)

hm2RingCplExtendedDiag		1.3.6.1.4.1.248.11.40.1.8.1.1.15
Additional operational states detected by the slave or in local mode. basicRedundancyInactive(2) indicates that the coupling port has been prevented from setting into forwarding (please see description of hm2RingCplCouplingLinks).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	noError(1), basicRedundancyInactive(2)

hm2RingCplNetCoupling		1.3.6.1.4.1.248.11.40.1.8.1.1.16
Specifies the kind of the coupled net segment. If two HIPER Rings are coupled ringCoupling(1) must be used. In netCoupling(2) the coupled segment is no HIPER Ring topology and the switches in the coupled net segment may be connected with other ports than their ringports. Notice: if the ring coupling mechanism switches over, in ringCoupling(1) only the address tables of the switches in the two coupled HIPER Rings will be erased, in netCoupling(2) the address tables of all switches in the coupled net will be erased.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ringCoupling(1), netCoupling(2)

hm2RingCplRedOperState		1.3.6.1.4.1.248.11.40.1.8.1.1.17
Operational state of the Ring/Net coupling redundancy. redGuaranteed(1) indicates that redundancy is guaranteed in the ring coupling. redNotGuaranteed(2) indicates that redundancy is not guaranteed in the ring coupling.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	redGuaranteed(1), redNotGuaranteed(2)

hm2RingCplRowStatus		1.3.6.1.4.1.248.11.40.1.8.1.1.22
Defines the status of a ring coupling database entry.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

hm2RedundantCplAdminState		1.3.6.1.4.1.248.11.40.1.9.1
Enables or disables the global RCP admin state.
Status: current	Access: read-write
OBJECT-TYPE
	HmEnabledStatus

hm2RedundantCplInPrimaryPort		1.3.6.1.4.1.248.11.40.1.9.2
The inner coupling port of the primary ring.
Status: current	Access: read-write
OBJECT-TYPE
	InterfaceIndexOrZero

hm2RedundantCplOutPrimaryPort		1.3.6.1.4.1.248.11.40.1.9.3
The outer coupling port of the primary ring.
Status: current	Access: read-write
OBJECT-TYPE
	InterfaceIndexOrZero

hm2RedundantCplInSecondaryPort		1.3.6.1.4.1.248.11.40.1.9.4
The inner coupling port of the secondary ring
Status: current	Access: read-write
OBJECT-TYPE
	InterfaceIndexOrZero

hm2RedundantCplOutSecondaryPort		1.3.6.1.4.1.248.11.40.1.9.5
The outer coupling port of the secondary ring
Status: current	Access: read-write
OBJECT-TYPE
	InterfaceIndexOrZero

hm2RedundantCplRole		1.3.6.1.4.1.248.11.40.1.9.6
Configurable role of the RCP coupler.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	master(1), slave(2), auto(4)

hm2RedundantCplCurrentRole		1.3.6.1.4.1.248.11.40.1.9.7
Current role of the RCP coupler.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	master(1), slave(2), listening(3), error(4), disabled(5)

hm2RedundantCplTimeout		1.3.6.1.4.1.248.11.40.1.9.8
RCP coupler timeout in milliseconds.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	5..60000

hm2RedundantCplPartner		1.3.6.1.4.1.248.11.40.1.9.9
MAC address of the coupling partner.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

hm2RedundantCplPartnerPrimaryPort		1.3.6.1.4.1.248.11.40.1.9.10
Port of the coupling partner in the primary ring.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndexOrZero

hm2RedundantCplPartnerSecodaryPort		1.3.6.1.4.1.248.11.40.1.9.11
Port of the coupling partner in the secondary ring.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndexOrZero

hm2RedundantCplState		1.3.6.1.4.1.248.11.40.1.9.12
current forwarding state of the RCP coupler.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	forwarding(1), blocking(2)

hm2RedundantCplRedundancyState		1.3.6.1.4.1.248.11.40.1.9.13
Indicates if coupling redundancy is available.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	redAvailable(1), redNotAvailable(2)

hm2RedundantCplPartnerIPAddrType		1.3.6.1.4.1.248.11.40.1.9.14
Partner IP Address type.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddressType

hm2RedundantCplPartnerIPAddr		1.3.6.1.4.1.248.11.40.1.9.15
IP address of the coupling partner.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddress

hm2MrpReconfig		1.3.6.1.4.1.248.11.40.0.1
This notification is sent if the MRP ring has switched over.
Status: current	Access: read-only
NOTIFICATION-TYPE

hm2SrmReconfig		1.3.6.1.4.1.248.11.40.0.2
This notification is sent if the SRM ring has switched over.
Status: current	Access: read-only
NOTIFICATION-TYPE

hm2RingCplReconfig		1.3.6.1.4.1.248.11.40.0.3
The Ring Coupling mechanism has switched over
Status: current	Access: read-only
NOTIFICATION-TYPE

hm2RedundantCplReconfig		1.3.6.1.4.1.248.11.40.0.4
The RCP Redundancy mechanism has switched over.
Status: current	Access: read-only
NOTIFICATION-TYPE

hm2RingCouplingMibSESGroup		1.3.6.1.4.1.248.11.40.3.8
OBJECT IDENTIFIER

hm2RedundantCplSESGroup		1.3.6.1.4.1.248.11.40.3.9
OBJECT IDENTIFIER

hm2RingCouplingInvalidPortConfiguration		1.3.6.1.4.1.248.11.40.3.8.1
Could not enable Ring/Net Coupling configuration. In {0} control mode the {1} should be selected, different from the coupling port and in the valid range.
Status: current	Access: read-only
OBJECT-IDENTITY

hm2RedundantCplPortsMissing		1.3.6.1.4.1.248.11.40.3.9.1
Could not enable RCP. The required ports are not configured.
Status: current	Access: read-only
OBJECT-IDENTITY