HH3C-FCOE-MIB

File: HH3C-FCOE-MIB.mib (19714 bytes)

Imported modules

HH3C-OID-MIB SNMPv2-SMI SNMPv2-TC
SNMP-FRAMEWORK-MIB IF-MIB Q-BRIDGE-MIB
T11-TC-MIB FC-MGMT-MIB

Imported symbols

hh3cCommon MODULE-IDENTITY OBJECT-TYPE
Unsigned32 RowStatus TimeStamp
TruthValue MacAddress TEXTUAL-CONVENTION
SnmpAdminString InterfaceIndex InterfaceIndexOrZero
VlanIndex T11FabricIndex fcmInstanceIndex

Defined Types

Hh3cFCoEVfcBindType  
TEXTUAL-CONVENTION    
  current INTEGER interfaceIndex(1), macAddress(2)

Hh3cFCoECfgEntry  
SEQUENCE    
  hh3cFCoECfgFcmap STRING
  hh3cFCoECfgDynamicVfcCreation TruthValue
  hh3cFCoECfgDefaultFCFPriority Unsigned32
  hh3cFCoECfgDATov Unsigned32
  hh3cFCoECfgAddressingMode INTEGER

Hh3cFCoEVLANEntry  
SEQUENCE    
  hh3cFCoEVLANIndex VlanIndex
  hh3cFCoEFabricIndex T11FabricIndex
  hh3cFCoEVLANOperState INTEGER
  hh3cFCoEVLANRowStatus RowStatus

Hh3cFCoEStaticVfcEntry  
SEQUENCE    
  hh3cFCoEStaticVfcIndex Unsigned32
  hh3cFCoEStaticVfcFCFPriority Unsigned32
  hh3cFCoEStaticVfcBindType Hh3cFCoEVfcBindType
  hh3cFCoEStaticVfcBindIfIndex InterfaceIndexOrZero
  hh3cFCoEStaticVfcBindMACAddress MacAddress
  hh3cFCoEStaticVfcIfIndex InterfaceIndex
  hh3cFCoEStaticVfcCreationTime TimeStamp
  hh3cFCoEStaticVfcFailureCause SnmpAdminString
  hh3cFCoEStaticVfcRowStatus RowStatus

Hh3cFCoEFIPSnoopingEntry  
SEQUENCE    
  hh3cFCoEFIPSnoopingVLANIndex VlanIndex
  hh3cFCoEFIPSnoopingEnable TruthValue
  hh3cFCoEFIPSnoopingFcmap STRING

Defined Values

hh3cFCoE 1.3.6.1.4.1.25506.2.120
This MIB module is for configuring and monitoring Fibre Channel over Ethernet (FCoE) related entities. This MIB defines a Virtual FC (VFC) Interface as an object that represents either a VF_Port or a VE_Port on a FCoE Forwarder (FCF). VFC interfaces can be created either statically (by management request) or dynamically (at the time of FIP based FLOGI or ELP request). Other terminologies used in this MIB are defined by the Hh3c FCoE standard, as defined in the FC-BB-5 specification. This MIB also supports configuration of the following objects: - Mapping of FCoE VLAN-ID used to carry traffic for a Fabric - FC-MAP value used by the FCF operating in FPMA mode - FIP snooping related objects
MODULE-IDENTITY    

hh3cFCoEObjects 1.3.6.1.4.1.25506.2.120.1
OBJECT IDENTIFIER    

hh3cFCoEConfig 1.3.6.1.4.1.25506.2.120.1.1
OBJECT IDENTIFIER    

hh3cFCoECfgTable 1.3.6.1.4.1.25506.2.120.1.1.1
This table facilitates configuration of FCoE parameters on a per Fibre Channel management instance.
OBJECT-TYPE    
  SEQUENCE OF  
    Hh3cFCoECfgEntry

hh3cFCoECfgEntry 1.3.6.1.4.1.25506.2.120.1.1.1.1
There is one entry in this table for each Fibre Channel management instance.
OBJECT-TYPE    
  Hh3cFCoECfgEntry  

hh3cFCoECfgFcmap 1.3.6.1.4.1.25506.2.120.1.1.1.1.1
This object configures the FC-MAP value used by the FCF when operating in FPMA mode. The default value is 0EFC00h, as written in the standard.
OBJECT-TYPE    
  STRING Size(3)  

hh3cFCoECfgDynamicVfcCreation 1.3.6.1.4.1.25506.2.120.1.1.1.1.2
This object is set to 'true' to enable, or 'false' to disable, the dynamic creation of VFC interfaces on this FCF. When set to 'true', VFC interfaces are dynamically created as and when a FIP-based FLOGI or ELP request is received.
OBJECT-TYPE    
  TruthValue  

hh3cFCoECfgDefaultFCFPriority 1.3.6.1.4.1.25506.2.120.1.1.1.1.3
The FIP priority value advertised by the FCF to ENodes by default. hh3cFCoEStaticVfcFCFPriority configured for a VFC interface overrides this setting for the ENode associated with the VFC.
OBJECT-TYPE    
  Unsigned32 0..255  

hh3cFCoECfgDATov 1.3.6.1.4.1.25506.2.120.1.1.1.1.4
The Discovery_Advertisement_Timeout value configured for the FCF. This is used as the timeout value in seconds by the FCF to send periodic Discovery Advertisements.
OBJECT-TYPE    
  Unsigned32 1..600  

hh3cFCoECfgAddressingMode 1.3.6.1.4.1.25506.2.120.1.1.1.1.5
Addressing mode(s) supported by the FCF. Implementations should fail SetRequests for unsupported modes.
OBJECT-TYPE    
  INTEGER fpma(1), spma(2), fpmaAndSpma(3)  

hh3cFCoEVLANTable 1.3.6.1.4.1.25506.2.120.1.1.2
In fabrics in which VLANs are deployed, this table facilitates configuration of VLAN and Virtual Fabric associations in an FCoE network. In such fabrics, FCoE forwarding for a fabric is over a VLAN in a (Layer-2) Ethernet network. That is, reachability between the ENode/remote-FCF and an FCF for a given fabric is determined by the reachability provided by the Ethernet network on the corresponding VLAN. An active entry in this table indicates which VLAN is used to transport FCoE traffic for a particular Virtual Fabric. If VLANs are not deployed or not enabled, entries in this table are ignored by the bridge. Some implmentations may allow traffic from only one Virtual Fabric to be transported over a given VLAN. Such implementations should prevent multiple entries with the same VLAN-ID from being created in this table. Modifying existing VLAN-Virtual Fabric associations is not possible. The specific row must first be deleted and then a new one created.
OBJECT-TYPE    
  SEQUENCE OF  
    Hh3cFCoEVLANEntry

hh3cFCoEVLANEntry 1.3.6.1.4.1.25506.2.120.1.1.2.1
There is one entry in this table for each VLAN that is designated to transport FCoE traffic for a given Virtual Fabric.
OBJECT-TYPE    
  Hh3cFCoEVLANEntry  

hh3cFCoEVLANIndex 1.3.6.1.4.1.25506.2.120.1.1.2.1.1
This object identifies the VLAN-ID that the FCoE FCF function is being enabled for.
OBJECT-TYPE    
  VlanIndex  

hh3cFCoEFabricIndex 1.3.6.1.4.1.25506.2.120.1.1.2.1.2
This object identifies the Fabric Index of the Virtual Fabric traffic which is to be transported over the VLAN identified by hh3cFCoEVLANIndex.
OBJECT-TYPE    
  T11FabricIndex  

hh3cFCoEVLANOperState 1.3.6.1.4.1.25506.2.120.1.1.2.1.3
Operational state of this VLAN-Virtual Fabric association entry. The 'up' state is achieved when both the Virtual Fabric and VLAN are valid.
OBJECT-TYPE    
  INTEGER up(1), down(2)  

hh3cFCoEVLANRowStatus 1.3.6.1.4.1.25506.2.120.1.1.2.1.4
The status of this conceptual row. The RowStatus becomes active on successful creation of an entry.
OBJECT-TYPE    
  RowStatus  

hh3cFCoEStaticVfcTable 1.3.6.1.4.1.25506.2.120.1.1.3
This table facilitates the creation and deletion of static VFC interfaces. While VFCs can be dynamically created based on FIP FLOGI/ELP requests, operators may want to associate certain pre-configured policy for a particular ENode or a remote-FCF. In such cases static VFC creation becomes necessary. In addition to being creating, a static VFC also needs to be associated to an ENode or remote-FCF. The VFC binding provides such an associaton. The binding does not need to be specified when the row for a VFC is created, but may be specified later.
OBJECT-TYPE    
  SEQUENCE OF  
    Hh3cFCoEStaticVfcEntry

hh3cFCoEStaticVfcEntry 1.3.6.1.4.1.25506.2.120.1.1.3.1
There is one entry in this table for each statically created VFC Interface.
OBJECT-TYPE    
  Hh3cFCoEStaticVfcEntry  

hh3cFCoEStaticVfcIndex 1.3.6.1.4.1.25506.2.120.1.1.3.1.1
This index uniquely identifies a static VFC entry in this table.
OBJECT-TYPE    
  Unsigned32 1..65535  

hh3cFCoEStaticVfcFCFPriority 1.3.6.1.4.1.25506.2.120.1.1.3.1.2
If this VFC is for a VF_Port this object is used to configure FCF priority to be advertised to the ENode associated with the VFC.
OBJECT-TYPE    
  Unsigned32 0..255  

hh3cFCoEStaticVfcBindType 1.3.6.1.4.1.25506.2.120.1.1.3.1.3
The mechanism to identify the ENode associated with this VFC if it is of type VF_Port or to identify the remote-FCF associated with this VFC if it is of type VE_Port.
OBJECT-TYPE    
  Hh3cFCoEVfcBindType  

hh3cFCoEStaticVfcBindIfIndex 1.3.6.1.4.1.25506.2.120.1.1.3.1.4
This object is applicable only when the local FCF is directly connected to an ENode or remote-FCF over a specific Ethernet interface, in which case this object contains the ifIndex of said Ethernet interface. If the ENode or remote-FCF is not directly connected to the FCF, this value of this object is zero.
OBJECT-TYPE    
  InterfaceIndexOrZero  

hh3cFCoEStaticVfcBindMACAddress 1.3.6.1.4.1.25506.2.120.1.1.3.1.5
This object is applicable when the ENode or remote-FCF to which the local FCF is connected is identified by a MAC address. A FIP frame from a ENode or remote-FCF is associated with this VFC only if the source MAC address in the frame is the same as the value of this object.
OBJECT-TYPE    
  MacAddress  

hh3cFCoEStaticVfcIfIndex 1.3.6.1.4.1.25506.2.120.1.1.3.1.6
The ifIndex of this Virtual FC interface.
OBJECT-TYPE    
  InterfaceIndex  

hh3cFCoEStaticVfcCreationTime 1.3.6.1.4.1.25506.2.120.1.1.3.1.7
The timestamp of this entry's creation time.
OBJECT-TYPE    
  TimeStamp  

hh3cFCoEStaticVfcFailureCause 1.3.6.1.4.1.25506.2.120.1.1.3.1.8
The cause of failure for the last bind operation. This object will be zero length if and only if the bind is successful.
OBJECT-TYPE    
  SnmpAdminString  

hh3cFCoEStaticVfcRowStatus 1.3.6.1.4.1.25506.2.120.1.1.3.1.9
The status of this conceptual row. The RowStatus becomes active on successful creation of a VFC. The VFC does not need to be bound for the row to be active, but the VFC must be bound before becoming operational.
OBJECT-TYPE    
  RowStatus  

hh3cFCoEFIPSnoopingTable 1.3.6.1.4.1.25506.2.120.1.1.4
FCoE provides increased flexibility, but with this flexibility new challenges arise in assuring highly robust Fabrics. The FCF does not have the complete control that a Fibre Channel switch has. Ethernet bridges commonly provide a feature called Access Control Lists (ACLs). Properly configured ACLs may emulate a point-to-point link by providing the traffic enforcement previously discussed. Furthermore, the FIP protocol has been designed to enable Ethernet bridges to efficiently monitor FIP frames passing through them. This data facilitates the automatic configuration of these ACLs. In addition, the automatic configuration is possible independent of any other ACLs that may be in use in the network for other applications. And FIP Snooping is to maintain these ACLs.
OBJECT-TYPE    
  SEQUENCE OF  
    Hh3cFCoEFIPSnoopingEntry

hh3cFCoEFIPSnoopingEntry 1.3.6.1.4.1.25506.2.120.1.1.4.1
There is one entry in this table for each VLAN that is designated to ensures that only valid FCoE traffic is allowed.
OBJECT-TYPE    
  Hh3cFCoEFIPSnoopingEntry  

hh3cFCoEFIPSnoopingVLANIndex 1.3.6.1.4.1.25506.2.120.1.1.4.1.1
This object identifies the VLAN-ID that the FIP Snooping function is being enabled for.
OBJECT-TYPE    
  VlanIndex  

hh3cFCoEFIPSnoopingEnable 1.3.6.1.4.1.25506.2.120.1.1.4.1.2
This object is used to enable or disable FIP Snooping on an Ethernet Bridge.
OBJECT-TYPE    
  TruthValue  

hh3cFCoEFIPSnoopingFcmap 1.3.6.1.4.1.25506.2.120.1.1.4.1.3
This object configures the FC-MAP value associated with the FIP snooping Ethernet Bridge.
OBJECT-TYPE    
  STRING Size(3)