GW-EPON-MIB

Imported modules

Imported symbols

devices	RowStatus	TruthValue
DisplayString	MacAddress	TEXTUAL-CONVENTION
DateAndTime	MODULE-IDENTITY	OBJECT-TYPE
Integer32	TimeTicks	NOTIFICATION-TYPE
Counter32	IpAddress

Defined Types

ChassisSlotSupportType
The value indicates the type of board this slot surpports.
TEXTUAL-CONVENTION
	BITS	sw(0), epon(1), gpon(2), get(3), geo(4), tdm(5), stm1(6), pwu48(7), pwu220(8), smb(9), gem(10), sig(11), onuEponB(12), onu6FeC(13), onu8FeD(14), onu16FeD(15), onu8PotsA(16), onu8PotsB(17), onu8FxsA(18), onu8FxsB(19), oltMain(20), olt2Epon(21), e1(22), oltE1(23), onuE1A(24), onuE1B(25), sw-6900(26), olt4epon(27), olt8epon(28), olt12epon(29), gem4ge(30), gem10ge(31), fan-6900(32), pwu-48(33), pwu-220(34), olt4epon4ge(35), pwu-220-6900m(36), pwu-48-6900m(37), fan-6900s(38), pwu-220-6900s(39), pwu-48-6900s(40)

OnuAlarmLevelList
Each octet within this value specifies a alarm-level of one ONU of a PON, with the first octet specifying ONU1 alarm-level, and the second octet specifying ONU2 alarm-level, etc. Per octet value is defined: '0' - null '1' - vital '2' - major '3' - minor '4' - warning '5' - clear '6' - information '7' - off-line.
TEXTUAL-CONVENTION
	OCTET STRING

EponDeviceType
The value indicates the type of this device: 1 - unknown, 2 - GFA6700, 3 - GFA6100, 4 - GT811, 5 - GT831, 6 - GT831-CATV, 7 - GT812, 8 - GT813, 9 - GT881, 10 - GT861, 11 - GT891, 12 - GT810, 13 - GT863, 14 - other, 15 - GT865, 16 - GT816, 17 - GT811A, 18 - GT812A, 19 - GT831A, 20 - GT831A-CATV, 21 - GT815, 22 - GT812B, 23 - GT831B, 24 - GT866, 25 - GT811-B, 26 - GT851, 27 - GT813-B, 28 - GT862, 29 - GT892, 30 - GT835, 31 - GT831-B-CATV, 32 - GT815-B, 33 - GT871, 34 - GT871R, 35 - GD5048, 36 - GD6024, 37 - GT872, 38 - GT872P, --GT872B(deprecated) 39 - GT872R, 40 - GT873, 41 - GT873P, 42 - GT873R, 43 - GT871P, 44 - GT870, 45 - GT811-C, 46 - GT810-A, 47 - GT811-D, 96 - GFA6900M, 97 - GGA6900S, 99 - GFA6900
TEXTUAL-CONVENTION
	Integer32

OnuList
Each octet within this value specifies a set of eight ONUs, with the first octet specifying ONUs ID 1 through 8, the second octet specifying ONUs ID 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered ONU ID, and the least significant bit represents the highest numbered ONU ID. Thus, each ONU of a PON is represented by a single bit within the value of this object. If the bit has a value of '1', then the ONU is registered and included in this list; if the bit has a value of '0', then the ONU is disregistered and not included.
TEXTUAL-CONVENTION
	OCTET STRING

ChassisSlotBoardType
The value indicates the type of this board: null(1) - NULL, unknown(2) - Unknown, sw(3) - SW (OLT), master control and switch board. epon(4) - EPON (OLT), slave epon board. gpon(5) - GPON (OLT), slave gpon board. get(6) - GET (OLT, 4GE-TX), using category 5 UTP interface. geo(7) - GEO (OLT, 4GE-XX), using X fiber over PMT interface. tdm(8) - TDM (OLT), slave tdm board. stm1(9) - STM1 (OLT), slave stm1 board. pwu48(10) - PWR48, power board with input of -48V(DC). pwu220(11) - PWR220, power board with input of 220V(AC). smb(12) - SMB (ONU), the simple mainboard of box device. gem(13) - GEM (OLT), slave board. sig(14) - SIG (OLT), slave board. onuEponB(15) - EPON-B (ONU). onu6FeC(16) - 6FE-C (ONU), RJ45 connector. onu8FeD(17) - 8FE-D (ONU), SCSI68 connector. onu16FeD(18) - 16FE-D (ONU), SCSI68 connector. onu8PotsA(19)- 8POTS-A (ONU), RJ11 connector. onu8PotsB(20)- 8POTS-B (ONU), RJ21 connector. onu8FxsA(21) - 8FXS-A (ONU), RJ11 connector. onu8FxsB(22) - 8FXS-B (ONU), RJ21 connector. oltMain(23) - the master board of box-device OLT. olt2Epon(24) - the EPON board of box-device OLT. E1 ( 25 ) - oltE1 ( 26 ) , onuE1A ( 27 ) , onuE1B ( 28 ) , sw-6900 ( 29 ) - SW (OLT), master control and switch board of GFA6900. olt4epon ( 30 ) - EPON (OLT) , PON board with 4 PON ports. olt8epon ( 31 ) - EPON (OLT) , PON board with 8 PON ports. olt12epon ( 32 ) - EPON (OLT) , PON board with 12 PON ports and 4 GE ports. gem4ge ( 33 ) - GEM (OLT) , GEM board with 4 GE ports. gem10ge ( 34 ) - GEM (OLT) , GEM board with 1 10GE port and 4 GE ports. fan-6900 ( 35 ) - FAN (OLT) , FAN board of GFA6900. pwu-48 ( 36 ) - PWU (OLT) , 48V Power board of GFA6900 and GFA6900M. pwu-220 ( 37 ) - PWU (OLT) , 220V Power board of GFA6900. olt4epon4ge(38) - EPON (OLT) , EPON board with 4 PON ports and 4 GE ports pwu-220-6900m(39) - PWU (OLT) , 220V Power board of GFA6900M. fan-6900s(40) - FAN (OLT) , FAN board of GFA6900S. pwu-48-6900s(41) - PWU (OLT) , 48V Power board of GFA6900S. pwu-220-6900s(42) - PWU (OLT) , 220V Power board of GFA6900S.
TEXTUAL-CONVENTION
	INTEGER	null(1), unknown(2), sw(3), epon(4), gpon(5), get(6), geo(7), tdm(8), stm1(9), pwu48(10), pwu220(11), smb(12), gem(13), sig(14), onuEponB(15), onu6FeC(16), onu8FeD(17), onu16FeD(18), onu8PotsA(19), onu8PotsB(20), onu8FxsA(21), onu8FxsB(22), oltMain(23), olt2Epon(24), e1(25), oltE1(26), onuE1A(27), onuE1B(28), sw-6900(29), olt4epon(30), olt8epon(31), olt12epon(32), gem4ge(33), gem10ge(34), fan-6900(35), pwu-48(36), pwu-220(37), olt4epon4ge(38), pwu-220-6900m(39), fan-6900s(40), pwu-48-6900s(41), pwu-220-6900s(42)

GwEponDevEntry
SEQUENCE
	deviceIndex	Integer32
	deviceType	EponDeviceType
	deviceName	DisplayString
	deviceDescription	DisplayString
	deviceLocation	DisplayString
	deviceVendor	DisplayString
	deviceFirmWareVersion	DisplayString
	deviceSoftWareVersion	DisplayString
	deviceHardWareVersion	DisplayString
	deviceOperStatus	INTEGER
	deviceAlarmStatus	INTEGER
	deviceMacAddress	MacAddress
	deviceLastChange	TimeTicks
	deviceReset	INTEGER
	deviceEntLogicalIndex	Integer32
	deviceEntLogicalCommunity	DisplayString
	deviceOnuTestDistance	Integer32
	deviceUpTime	TimeTicks
	deviceStpEnable	INTEGER
	deviceChipsetVendor	DisplayString
	deviceChipsetMode	Integer32
	deviceChipsetRevision	DisplayString
	deviceChipsetDate	DisplayString
	deviceCapPortDesc	DisplayString
	deviceCapEthPortNum	Integer32
	deviceCapIadPotsPortNum	Integer32
	deviceCapE1PortNum	Integer32
	deviceCapUQueueTotal	Integer32
	deviceCapUQueuePort	Integer32
	deviceCapDQueueTotal	Integer32
	deviceCapDQueuePort	Integer32
	deviceCapBattery	INTEGER
	deviceMulticastSwitch	INTEGER
	deviceSystemTime	DateAndTime
	deviceRestartupTime	DateAndTime
	deviceTrafficServiceStatus	INTEGER
	deviceAlarmMask	BITS
	deviceModel	DisplayString
	deviceMulticastFastLeaveAbility	BITS
	deviceMulticastFastLeaveOperState	INTEGER
	deviceMulticastFastLeaveAdminState	INTEGER
	onuMacTableAlarmThreshold	Integer32
	onuMacNumbers	Integer32

GwEponBoardEntry
SEQUENCE
	boardIndex	Integer32
	curBoardType	ChassisSlotBoardType
	boardDescription	DisplayString
	boardActMode	INTEGER
	boardOperStatus	INTEGER
	boardAlarmLevel	INTEGER
	boardLastChangeTime	TimeTicks
	boardSupprotType	ChassisSlotSupportType
	boardReset	INTEGER
	boardTemperature	Integer32
	boardEntLogicalIndex	Integer32
	boardEntLogicalCommunity	DisplayString
	boardSoftwareVersion	DisplayString
	boardFirmwareVersion	DisplayString
	boardBootVersion	DisplayString
	boardHardwareVersion	DisplayString
	boardManufactureDate	DisplayString
	boardSerialNo	DisplayString
	boardCpuUsage	Integer32
	boardMemoryUsage	Integer32
	boardHasSnmpAgent	INTEGER
	boardSnmpAgentIpAddr	IpAddress
	boardSnmpAgentReadCommunity	DisplayString
	boardSnmpAgentWriteCommunity	DisplayString
	boardTemperatureHighThresholds	Integer32
	boardCpuUsageThresholds	Integer32
	boardMemoryUsageThresholds	Integer32
	boardMemorySize	Integer32
	boardTemperatureLowThresholds	Integer32
	boardAdminStatus	INTEGER

PonPortEntry
SEQUENCE
	ponPortIndex	Integer32
	ponPortIfIndex	Integer32
	ponPortDot1dBasePort	Integer32
	ponPortPartnerDev	Integer32
	ponPortPartnerBrd	Integer32
	ponPortPartnerPort	Integer32
	ponPortProtectionDev	Integer32
	ponPortProtectionBrd	Integer32
	ponPortProtectionPort	Integer32
	ponPortType	INTEGER
	ponPortMaxOnu	Integer32
	ponPortCurrOnu	Integer32
	ponPortOperStatus	INTEGER
	ponPortAlarmStatus	BITS
	ponPortAlarmMask	BITS
	ponPortMaxBW	Integer32
	ponPortActBW	Integer32
	ponPortRemainBW	Integer32
	ponPortApsCtrl	INTEGER
	ponPortApsStatus	INTEGER
	ponPortEncryptSet	INTEGER
	ponPortOnuLpbCtrl	INTEGER
	ponPortOnuLpbSource	INTEGER
	ponPortOnuLpbTime	Integer32
	ponPortOnuLpbTxFrms	Counter32
	ponPortOnuLpbRxFrms	Counter32
	ponEntLogicalIndex	Integer32
	ponEntLogicalCommunity	DisplayString
	ponPortLinkedOnuCounter	Integer32
	ponPortAdminStatus	INTEGER
	ponPortReset	INTEGER
	ponPortWindowRange	INTEGER
	ponPortDownlinkPolicingEbl	INTEGER
	ponPortAllOnuAlmLevel	OnuAlarmLevelList

PonOnuMapEntry
SEQUENCE
	mappingOnuIndex	Integer32
	onuDevIndex	Integer32
	onuName	DisplayString

PonPerfMonEntry
SEQUENCE
	ponPerfBER	Counter32
	ponPerfFER	Counter32
	ponPerfBerAlmEnable	INTEGER
	ponPerfFerAlmEnable	INTEGER
	ponPerfUpBandwidth	Counter32
	ponPerfDownBandwidth	Counter32

PonHisCtrlEntry
SEQUENCE
	ponHis15MinuteEnable	INTEGER
	ponHis24HourEnable	INTEGER

OnuAuthEntry
SEQUENCE
	eponBoardIndex	Integer32
	eponPonPortIndex	Integer32
	onuAuthIndex	Integer32
	onuAuthMacAddress	MacAddress
	onuAuthRowStatus	RowStatus

OnuAuthModeEntry
SEQUENCE
	onuAuthModeBrdIdx	Integer32
	onuAuthModePonIdx	Integer32
	onuAuthMode	INTEGER
	onuAuthEnableForPon	INTEGER
	onuAuthEntryReorganize	INTEGER

OnuAuthLoidEntry
SEQUENCE
	onuAuthLoidBrdIdx	Integer32
	onuAuthLoidPonIdx	Integer32
	onuAuthLoidIdx	Integer32
	onuAuthLoid	DisplayString
	onuAuthLoidPassword	DisplayString
	onuAuthLoidDevIdx	Integer32
	onuAuthLoidRowStatus	RowStatus

OnuAuth1Entry
SEQUENCE
	eponUnauthenticatedBoardIndex	Integer32
	eponUnauthenticatedPonPortIndex	Integer32
	onuUnauthenticatedIndex	Integer32
	onuUnauthenticatedMacAddress	MacAddress

PonLlidEntry
SEQUENCE
	ponLlidIndex	Integer32
	ponLlidType	INTEGER
	ponLlidOltBoard	Integer32
	ponLlidOltPort	Integer32
	ponLlidOltPortIfIndex	Integer32
	ponLlidOnuPortIfIndex	Integer32
	ponLlidOnuBoard	Integer32
	ponLlidOnuPort	Integer32
	ponLlidLLID	Integer32
	ponLlidIfIndex	Integer32
	ponLlidUpFixedBW	Integer32
	ponLlidDownFixedBW	Integer32
	ponLlidDesc	DisplayString
	ponLlidSurportMacNum	Integer32
	ponLlidOnuMacAddress	MacAddress
	ponLlidRowStatus	RowStatus
	ponLlidUpBWClass	Integer32
	ponLlidUpDelay	INTEGER
	ponLlidUpAssuredBW	Integer32
	ponLlidUpBesteffortBW	Integer32
	ponLlidDownBWClass	Integer32
	ponLlidDownDelay	INTEGER
	ponLlidDownAssuredBW	Integer32
	ponLlidDownBesteffortBW	Integer32
	ponLlidCtcFecAbility	INTEGER
	ponLlidCtcFecMode	INTEGER
	ponLlidCtcEncrypCtrl	INTEGER
	ponLlidCtcDbaQueSetNum	Integer32
	ponLlidCtcDbaQueSetCfgStatus	INTEGER

PonLlidCtcDbaQueSetEntry
SEQUENCE
	ponLlidCtcDbaQueSetIndex	Integer32
	ponLlidCtcDbaReportBitmap	BITS
	ponLlidCtcDbaQueue0Threshold	Integer32
	ponLlidCtcDbaQueue1Threshold	Integer32
	ponLlidCtcDbaQueue2Threshold	Integer32
	ponLlidCtcDbaQueue3Threshold	Integer32
	ponLlidCtcDbaQueue4Threshold	Integer32
	ponLlidCtcDbaQueue5Threshold	Integer32
	ponLlidCtcDbaQueue6Threshold	Integer32
	ponLlidCtcDbaQueue7Threshold	Integer32

Defined Values

gwEponMib		1.3.6.1.4.1.10072.2.20
EPON private MIB information definitions
MODULE-IDENTITY

gwEponMibObjects		1.3.6.1.4.1.10072.2.20.1
OBJECT IDENTIFIER

gwEponCfgGroup		1.3.6.1.4.1.10072.2.20.1.1
OBJECT IDENTIFIER

gwEponDevice		1.3.6.1.4.1.10072.2.20.1.1.1
OBJECT IDENTIFIER

gwEponBoard		1.3.6.1.4.1.10072.2.20.1.1.2
OBJECT IDENTIFIER

gwEponPon		1.3.6.1.4.1.10072.2.20.1.1.3
OBJECT IDENTIFIER

gwEponPonOnuAuth		1.3.6.1.4.1.10072.2.20.1.1.4
OBJECT IDENTIFIER

gwEponLlid		1.3.6.1.4.1.10072.2.20.1.1.5
OBJECT IDENTIFIER

gwDevTrapGroup		1.3.6.1.4.1.10072.2.20.1.1.6
OBJECT IDENTIFIER

gwAlarmLevelGroup		1.3.6.1.4.1.10072.2.20.1.1.7
OBJECT IDENTIFIER

gwConsoleCfgGroup		1.3.6.1.4.1.10072.2.20.1.1.8
OBJECT IDENTIFIER

gwEponDevTable		1.3.6.1.4.1.10072.2.20.1.1.1.1
Table of device informations
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		GwEponDevEntry

gwEponDevEntry		1.3.6.1.4.1.10072.2.20.1.1.1.1.1
An entry in the table, containing properties and some descriptions
Status: current	Access: not-accessible
OBJECT-TYPE
	GwEponDevEntry

deviceIndex		1.3.6.1.4.1.10072.2.20.1.1.1.1.1.1
Index of device
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

deviceType		1.3.6.1.4.1.10072.2.20.1.1.1.1.1.2
The value indicates the type of this device
Status: current	Access: read-only
OBJECT-TYPE
	EponDeviceType

deviceName		1.3.6.1.4.1.10072.2.20.1.1.1.1.1.3
A string indicates or configure device name
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

deviceDescription		1.3.6.1.4.1.10072.2.20.1.1.1.1.1.4
Description for this device
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..255)

deviceLocation		1.3.6.1.4.1.10072.2.20.1.1.1.1.1.5
A string indicates and configure the device location
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..255)

deviceVendor		1.3.6.1.4.1.10072.2.20.1.1.1.1.1.6
A string indicates the vendor
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..255)

deviceFirmWareVersion		1.3.6.1.4.1.10072.2.20.1.1.1.1.1.7
The value indicates the version of firmware
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(20)

deviceSoftWareVersion		1.3.6.1.4.1.10072.2.20.1.1.1.1.1.8
The value indicates the version of software
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(20)

deviceHardWareVersion		1.3.6.1.4.1.10072.2.20.1.1.1.1.1.9
The value indicates the version of PCB
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(20)

deviceOperStatus		1.3.6.1.4.1.10072.2.20.1.1.1.1.1.10
The current operational state of the device, 'down(2)' indicates that the ONU is off-line. 'dormant(4)' indicates the device is waiting for external actions (such as no bandwidth for any service), 'powerDown(5)' indicates the device is power down or dying gasp.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2), unknown(3), dormant(4), powerDown(5)

deviceAlarmStatus		1.3.6.1.4.1.10072.2.20.1.1.1.1.1.11
The value indicates alarm status for this device, it means unique alarm occur that unique bit is set '1', on the other hand, unique bit is set 0 while this alarm is cleared.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	vital(1), major(2), minor(3), warning(4), clear(5)

deviceMacAddress		1.3.6.1.4.1.10072.2.20.1.1.1.1.1.12
The value indicates and confgure device MAC address
Status: current	Access: read-write
OBJECT-TYPE
	MacAddress	Size(6)

deviceLastChange		1.3.6.1.4.1.10072.2.20.1.1.1.1.1.15
the last time for this device change
Status: current	Access: read-only
OBJECT-TYPE
	TimeTicks

deviceReset		1.3.6.1.4.1.10072.2.20.1.1.1.1.1.16
Description
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noop(1), reset(2)

deviceEntLogicalIndex		1.3.6.1.4.1.10072.2.20.1.1.1.1.1.17
The value of this object uniquely identifies the logical entity. The value should be a small positive integer; index values for different logical entities are are not necessarily contiguous.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..2147483647

deviceEntLogicalCommunity		1.3.6.1.4.1.10072.2.20.1.1.1.1.1.18
An SNMPv1 or SNMPv2C community-string which can be used to access detailed management information for this logical entity. The agent should allow read access with this community string (to an appropriate subset of all managed objects) and may also return a community string based on the privileges of the request used to read this object. Note that an agent may return a community string with read-only privileges, even if this object is accessed with a read- write community string. However, the agent must take care not to return a community string which allows more privileges than the community string used to access this object. A compliant SNMP agent may wish to conserve naming scopes by representing multiple logical entities in a single 'default' naming scope. This is possible when the logical entities represented by the same value of entLogicalCommunity have no object instances in common. For example, 'bridge1' and 'repeater1' may be part of the main naming scope, but at least one additional community string is needed to represent 'bridge2' and 'repeater2'. Logical entities 'bridge1' and 'repeater1' would be represented by sysOREntries associated with the 'default' naming scope. For agents not accessible via SNMPv1 or SNMPv2C, the value of this object is the empty string. This object may also contain an empty string if a community string has not yet been assigned by the agent, or no community string with suitable access rights can be returned for a particular SNMP request. Note that this object is deprecated. Agents which implement SNMPv3 access should use the entLogicalContextEngineID and entLogicalContextName objects to identify the context associated with each logical entity. SNMPv3 agents may return a zero-length string for this object, or may continue to return a community string (e.g., tri-lingual agent support).
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..20)

deviceOnuTestDistance		1.3.6.1.4.1.10072.2.20.1.1.1.1.1.19
the distance between OLT and unique ONU, unit:meter
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

deviceUpTime		1.3.6.1.4.1.10072.2.20.1.1.1.1.1.20
The value of this object uniquely identifies up time about this device.
Status: current	Access: read-only
OBJECT-TYPE
	TimeTicks

deviceStpEnable		1.3.6.1.4.1.10072.2.20.1.1.1.1.1.21
OLT or ONU spanning tree contral, enable(1)- enable the spanning tree protocol, disable(2)- disable the spanning tree protocol.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

deviceChipsetVendor		1.3.6.1.4.1.10072.2.20.1.1.1.1.1.22
PON chipset vendor ID
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

deviceChipsetMode		1.3.6.1.4.1.10072.2.20.1.1.1.1.1.23
PON chipset type
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

deviceChipsetRevision		1.3.6.1.4.1.10072.2.20.1.1.1.1.1.24
PON chipset revision
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

deviceChipsetDate		1.3.6.1.4.1.10072.2.20.1.1.1.1.1.25
PON chipset design date
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

deviceCapPortDesc		1.3.6.1.4.1.10072.2.20.1.1.1.1.1.26
Port capabilities description, include GE/FE/E1/POTS etc.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

deviceCapEthPortNum		1.3.6.1.4.1.10072.2.20.1.1.1.1.1.27
Number of ethernet port supported
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

deviceCapIadPotsPortNum		1.3.6.1.4.1.10072.2.20.1.1.1.1.1.28
Number of POTS port of IAD supported
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

deviceCapE1PortNum		1.3.6.1.4.1.10072.2.20.1.1.1.1.1.29
Number of E1 port supported
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

deviceCapUQueueTotal		1.3.6.1.4.1.10072.2.20.1.1.1.1.1.30
Number of upstream queues
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

deviceCapUQueuePort		1.3.6.1.4.1.10072.2.20.1.1.1.1.1.31
Maximum queues per port upstream
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

deviceCapDQueueTotal		1.3.6.1.4.1.10072.2.20.1.1.1.1.1.32
Number of downstream queues
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

deviceCapDQueuePort		1.3.6.1.4.1.10072.2.20.1.1.1.1.1.33
Maximum queues per port downstream
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

deviceCapBattery		1.3.6.1.4.1.10072.2.20.1.1.1.1.1.34
Battery Backup
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

deviceMulticastSwitch		1.3.6.1.4.1.10072.2.20.1.1.1.1.1.35
ONU multicast switch
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	snooping(1), ctc(2)

deviceSystemTime		1.3.6.1.4.1.10072.2.20.1.1.1.1.1.36
Current system clock-time. OCTET-STRING consisting of eleven octets whose contents are defined by RFC2579.
Status: current	Access: read-write
OBJECT-TYPE
	DateAndTime

deviceRestartupTime		1.3.6.1.4.1.10072.2.20.1.1.1.1.1.37
The time of device(OLT or ONU) restartup-time. OCTET-STRING consisting of eleven octets whose contents are defined by RFC2579.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

deviceTrafficServiceStatus		1.3.6.1.4.1.10072.2.20.1.1.1.1.1.38
ONU traffic service state. 'enable(1)' indicates the traffic is in-service. 'disable(2)' indicates the traffic is out of service, but is still registered.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

deviceAlarmMask		1.3.6.1.4.1.10072.2.20.1.1.1.1.1.39
.
Status: current	Access: read-write
OBJECT-TYPE
	BITS	power(0), fan(1), cpu(2), temperature(3), register(4), present(5), ethlink(6), ethfer(7), ethflr(8), ethti(9), ethloop(10), ponber(11), ponfer(12), ponabnormal(13), ponaps(14), ponlink(15), onuLaserAlwayOn(16), onuOpticalPowerLow(17), onuOpticalPowerHigh(18), ponLOS(19)

deviceModel		1.3.6.1.4.1.10072.2.20.1.1.1.1.1.40
.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..32)

deviceMulticastFastLeaveAbility		1.3.6.1.4.1.10072.2.20.1.1.1.1.1.41
Fast Leave Mode: If the bit value of 'ctc(0)' is 0, the mode is CTC and non-fast-leave function, if the bit value of 'ctc(0)' is 1, the mode is CTC and fast-leave function; If the bit value of 'snooping(1)' is 0, the mode is snooping and non-fast-leave function, If the bit value of 'snooping(1)' is 1, the mode is snooping and fast-leave function.
Status: current	Access: read-only
OBJECT-TYPE
	BITS	ctc(0), snooping(1)

deviceMulticastFastLeaveOperState		1.3.6.1.4.1.10072.2.20.1.1.1.1.1.42
Fast Leave Function is active or deactive
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	active(1), deactive(2)

deviceMulticastFastLeaveAdminState		1.3.6.1.4.1.10072.2.20.1.1.1.1.1.43
active or deactivate Fast Leave Function
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	active(1), deactive(2)

onuMacTableAlarmThreshold		1.3.6.1.4.1.10072.2.20.1.1.1.1.1.44
onu MAC table alarm threshold
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

onuMacNumbers		1.3.6.1.4.1.10072.2.20.1.1.1.1.1.45
show onu actual mac number
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

gwEponBoardTable		1.3.6.1.4.1.10072.2.20.1.1.2.1
table of board informations
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		GwEponBoardEntry

gwEponBoardEntry		1.3.6.1.4.1.10072.2.20.1.1.2.1.1
An entry in the table, containig status and configrue information about boards
Status: current	Access: not-accessible
OBJECT-TYPE
	GwEponBoardEntry

boardIndex		1.3.6.1.4.1.10072.2.20.1.1.2.1.1.1
index of boards in unique device which is specified by 'deviceIndex'
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

curBoardType		1.3.6.1.4.1.10072.2.20.1.1.2.1.1.2
The value indicates the type of this board.
Status: current	Access: read-only
OBJECT-TYPE
	ChassisSlotBoardType

boardDescription		1.3.6.1.4.1.10072.2.20.1.1.2.1.1.3
The value indicates and confgure board description
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..255)

boardActMode		1.3.6.1.4.1.10072.2.20.1.1.2.1.1.4
The value indicates acting mode of unique board
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	master-active(1), master-redundancy(2), slave(3), unknown(4)

boardOperStatus		1.3.6.1.4.1.10072.2.20.1.1.2.1.1.5
The Value indicates board operating status
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	null(1), initing(2), upgrating(3), running(4), exception(5)

boardAlarmLevel		1.3.6.1.4.1.10072.2.20.1.1.2.1.1.6
The value indicates alarm level for unique board
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	vital(1), major(2), minor(3), warning(4), noAlarm(5)

boardLastChangeTime		1.3.6.1.4.1.10072.2.20.1.1.2.1.1.7
the time of last change about this board
Status: current	Access: read-only
OBJECT-TYPE
	TimeTicks

boardSupprotType		1.3.6.1.4.1.10072.2.20.1.1.2.1.1.8
The value indicates the type of board this slot surpports.
Status: current	Access: read-only
OBJECT-TYPE
	ChassisSlotSupportType

boardReset		1.3.6.1.4.1.10072.2.20.1.1.2.1.1.9
The value of this object determines whether reset this board. 'noop(1)' - only read value. 'reset(2)' - only write value, if the active master board is resetted, and another master board is running, then, the two boards will be switchover.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noop(1), reset(2)

boardTemperature		1.3.6.1.4.1.10072.2.20.1.1.2.1.1.10
The value indicates the temperature of this board
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

boardEntLogicalIndex		1.3.6.1.4.1.10072.2.20.1.1.2.1.1.11
The value of this object uniquely identifies the logical entity. The value should be a small positive integer; index values for different logical entities are are not necessarily contiguous.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..2147483647

boardEntLogicalCommunity		1.3.6.1.4.1.10072.2.20.1.1.2.1.1.12
An SNMPv1 or SNMPv2C community-string which can be used to access detailed management information for this logical entity. The agent should allow read access with this community string (to an appropriate subset of all managed objects) and may also return a community string based on the privileges of the request used to read this object. Note that an agent may return a community string with read-only privileges, even if this object is accessed with a read- write community string. However, the agent must take care not to return a community string which allows more privileges than the community string used to access this object. A compliant SNMP agent may wish to conserve naming scopes by representing multiple logical entities in a single 'default' naming scope. This is possible when the logical entities represented by the same value of entLogicalCommunity have no object instances in common. For example, 'bridge1' and 'repeater1' may be part of the main naming scope, but at least one additional community string is needed to represent 'bridge2' and 'repeater2'. Logical entities 'bridge1' and 'repeater1' would be represented by sysOREntries associated with the 'default' naming scope. For agents not accessible via SNMPv1 or SNMPv2C, the value of this object is the empty string. This object may also contain an empty string if a community string has not yet been assigned by the agent, or no community string with suitable access rights can be returned for a particular SNMP request. Note that this object is deprecated. Agents which implement SNMPv3 access should use the entLogicalContextEngineID and entLogicalContextName objects to identify the context associated with each logical entity. SNMPv3 agents may return a zero-length string for this object, or may continue to return a community string (e.g., tri-lingual agent support).
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..20)

boardSoftwareVersion		1.3.6.1.4.1.10072.2.20.1.1.2.1.1.13
the value indicates the version of software
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..20)

boardFirmwareVersion		1.3.6.1.4.1.10072.2.20.1.1.2.1.1.14
the value indicates the version of firmware
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..20)

boardBootVersion		1.3.6.1.4.1.10072.2.20.1.1.2.1.1.15
Boot Version
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..20)

boardHardwareVersion		1.3.6.1.4.1.10072.2.20.1.1.2.1.1.16
Hardware Version
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..20)

boardManufactureDate		1.3.6.1.4.1.10072.2.20.1.1.2.1.1.17
Manufacture Date
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..20)

boardSerialNo		1.3.6.1.4.1.10072.2.20.1.1.2.1.1.18
Manufacture Serial No
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..20)

boardCpuUsage		1.3.6.1.4.1.10072.2.20.1.1.2.1.1.19
The percentage of CPU usage
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

boardMemoryUsage		1.3.6.1.4.1.10072.2.20.1.1.2.1.1.20
The percentage of used memory
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

boardHasSnmpAgent		1.3.6.1.4.1.10072.2.20.1.1.2.1.1.21
the object indicates whether there is a SNMP agent running on this board.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notpresent(0), snmpv1(1), snmpv2c(2), snmpv3(3)

boardSnmpAgentIpAddr		1.3.6.1.4.1.10072.2.20.1.1.2.1.1.22
this object indicates and configure IP address of SNMP agent running on this board. now, only GT861's IAD boards surpport this function.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

boardSnmpAgentReadCommunity		1.3.6.1.4.1.10072.2.20.1.1.2.1.1.23
the object indicates and configure the read-only community of SNMP agent running on the board. now, only GT861's IAD boards surpport this function.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..16)

boardSnmpAgentWriteCommunity		1.3.6.1.4.1.10072.2.20.1.1.2.1.1.24
the object indicates and configure the read-write community of SNMP agent running on the board. now, only GT861's IAD boards surpport this function.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..16)

boardTemperatureHighThresholds		1.3.6.1.4.1.10072.2.20.1.1.2.1.1.25
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

boardCpuUsageThresholds		1.3.6.1.4.1.10072.2.20.1.1.2.1.1.26
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

boardMemoryUsageThresholds		1.3.6.1.4.1.10072.2.20.1.1.2.1.1.27
The percentage of used memory
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

boardMemorySize		1.3.6.1.4.1.10072.2.20.1.1.2.1.1.28
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

boardTemperatureLowThresholds		1.3.6.1.4.1.10072.2.20.1.1.2.1.1.29
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

boardAdminStatus		1.3.6.1.4.1.10072.2.20.1.1.2.1.1.30
The desired state of the board.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	up(1), down(2)

ponPortTable		1.3.6.1.4.1.10072.2.20.1.1.3.1
table of pon port informations
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PonPortEntry

ponPortEntry		1.3.6.1.4.1.10072.2.20.1.1.3.1.1
An entry in the table, containing status and configure information about pon port
Status: current	Access: not-accessible
OBJECT-TYPE
	PonPortEntry

ponPortIndex		1.3.6.1.4.1.10072.2.20.1.1.3.1.1.1
index of pon port
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..2147483647

ponPortIfIndex		1.3.6.1.4.1.10072.2.20.1.1.3.1.1.2
The value equipped to the index of this pon port in the IF-MIB
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..2147483647

ponPortDot1dBasePort		1.3.6.1.4.1.10072.2.20.1.1.3.1.1.3
port id in the bridge, equipped to the value in the bridge 'dot1dBasePort'
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..65536

ponPortPartnerDev		1.3.6.1.4.1.10072.2.20.1.1.3.1.1.4
index of the device which contains parter pon port
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ponPortPartnerBrd		1.3.6.1.4.1.10072.2.20.1.1.3.1.1.5
index of board which contains parter pon port
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ponPortPartnerPort		1.3.6.1.4.1.10072.2.20.1.1.3.1.1.6
partnet physical pon port index
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ponPortProtectionDev		1.3.6.1.4.1.10072.2.20.1.1.3.1.1.7
PON Automatic Protection Switching, index of device
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

ponPortProtectionBrd		1.3.6.1.4.1.10072.2.20.1.1.3.1.1.8
PON Automatic Protection Switching, index of board
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

ponPortProtectionPort		1.3.6.1.4.1.10072.2.20.1.1.3.1.1.9
PON Automatic Protection Switching, index of pon port
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

ponPortType		1.3.6.1.4.1.10072.2.20.1.1.3.1.1.10
type of pon port
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	eponMauType1000BasePXOLT(1), eponMauType1000BasePXONU(2), eponMauType1000BasePX10DOLT(3), eponMauType1000BasePX10DONU(4), eponMauType1000BasePX10UOLT(5), eponMauType1000BasePX10UONU(6), eponMauType1000BasePX20DOLT(7), eponMauType1000BasePX20DONU(8), eponMauType1000BasePX20UOLT(9), eponMauType1000BasePX20UONU(10)

ponPortMaxOnu		1.3.6.1.4.1.10072.2.20.1.1.3.1.1.11
The max number of supported ONUs in this PON port.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..2147483647

ponPortCurrOnu		1.3.6.1.4.1.10072.2.20.1.1.3.1.1.12
The current number of registered ONUs in this PON port.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..64

ponPortOperStatus		1.3.6.1.4.1.10072.2.20.1.1.3.1.1.13
operation status of unique pon port
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2), unknown(3), loop(4)

ponPortAlarmStatus		1.3.6.1.4.1.10072.2.20.1.1.3.1.1.14
PON port alarm status, it indicates an alarm with bit=1, if all bit is 0, indicates no alarm.
Status: current	Access: read-only
OBJECT-TYPE
	BITS	ber(0), fer(1), abnormal(2), aps(3), link(4), onuLaserAlwaysOn(5), onuOpticalPowerLow(6), onuOpticalPowerHigh(7), ponLOS(8)

ponPortAlarmMask		1.3.6.1.4.1.10072.2.20.1.1.3.1.1.15
PON Port Alarm mask, the bit=1 indicates mask.
Status: current	Access: read-write
OBJECT-TYPE
	BITS	ber(0), fer(1), abnormal(2), aps(3), link(4), onuLaserAlwaysOn(5), onuOpticalPowerLow(6), onuOpticalPowerHigh(7), ponLOS(8)

ponPortMaxBW		1.3.6.1.4.1.10072.2.20.1.1.3.1.1.16
The max bandwidth supported, unit:KB.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..1000000

ponPortActBW		1.3.6.1.4.1.10072.2.20.1.1.3.1.1.17
the actual bandwidth, unit:KB.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

ponPortRemainBW		1.3.6.1.4.1.10072.2.20.1.1.3.1.1.18
The current available bandwidth, unit:KB.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..1000000

ponPortApsCtrl		1.3.6.1.4.1.10072.2.20.1.1.3.1.1.19
PON automatic-protection-switching control.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), auto(2), force(3)

ponPortApsStatus		1.3.6.1.4.1.10072.2.20.1.1.3.1.1.20
PON automatic-protection-switching status.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), active(2), passive(3)

ponPortEncryptSet		1.3.6.1.4.1.10072.2.20.1.1.3.1.1.21
Encryption set according to every ONU, this value is ignored when the pon port belongs to OLT.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	pure(1), downstreamonly(2), bidirectional(3)

ponPortOnuLpbCtrl		1.3.6.1.4.1.10072.2.20.1.1.3.1.1.22
ONU Loopback Control, 'noop(1)' is no operation, i.e. the current status is idle; 'lpbStart(2)' is start loopback, only when the object value is 'noop', it can be configurated 'lpbStart(2)', otherwise forbidden, and if success, its value become 'inProcess(4)'; 'lpbStop(3)' is stop loopback, only when the object value is 'inProcess(4)', it can be configurated 'lpbStop(3)', and if success, its value become 'noop(1)'; 'inProcess(4)' is loopbacking status now.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noop(1), lpbStart(2), lpbStop(3), inProcess(4)

ponPortOnuLpbSource		1.3.6.1.4.1.10072.2.20.1.1.3.1.1.23
Loopback Data Source, 'internal' indicates internal data source, to use testing the link up or down, like ping function; 'external' indicates external data source, to use testing the bandwidth of the ONU ethernet.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	internal(1), external(2)

ponPortOnuLpbTime		1.3.6.1.4.1.10072.2.20.1.1.3.1.1.24
Loopback Timeout, if the object value is 0, indicate the loopback is processing at all time, if the value is none 0, indicate the loopback time from begin to end, when the time is end it will be auto-stopped. unit:second.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..2147483647

ponPortOnuLpbTxFrms		1.3.6.1.4.1.10072.2.20.1.1.3.1.1.25
The number of frames transmit by this ONU Logical Link.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ponPortOnuLpbRxFrms		1.3.6.1.4.1.10072.2.20.1.1.3.1.1.26
The number of frames transmit by this ONU Logical Link.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ponEntLogicalIndex		1.3.6.1.4.1.10072.2.20.1.1.3.1.1.27
The value of this object uniquely identifies the logical entity. The value should be a small positive integer; index values for different logical entities are are not necessarily contiguous.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..2147483647

ponEntLogicalCommunity		1.3.6.1.4.1.10072.2.20.1.1.3.1.1.28
An SNMPv1 or SNMPv2C community-string which can be used to access detailed management information for this logical entity. The agent should allow read access with this community string (to an appropriate subset of all managed objects) and may also return a community string based on the privileges of the request used to read this object. Note that an agent may return a community string with read-only privileges, even if this object is accessed with a read- write community string. However, the agent must take care not to return a community string which allows more privileges than the community string used to access this object. A compliant SNMP agent may wish to conserve naming scopes by representing multiple logical entities in a single 'default' naming scope. This is possible when the logical entities represented by the same value of entLogicalCommunity have no object instances in common. For example, 'bridge1' and 'repeater1' may be part of the main naming scope, but at least one additional community string is needed to represent 'bridge2' and 'repeater2'. Logical entities 'bridge1' and 'repeater1' would be represented by sysOREntries associated with the 'default' naming scope. For agents not accessible via SNMPv1 or SNMPv2C, the value of this object is the empty string. This object may also contain an empty string if a community string has not yet been assigned by the agent, or no community string with suitable access rights can be returned for a particular SNMP request. Note that this object is deprecated. Agents which implement SNMPv3 access should use the entLogicalContextEngineID and entLogicalContextName objects to identify the context associated with each logical entity. SNMPv3 agents may return a zero-length string for this object, or may continue to return a community string (e.g., tri-lingual agent support).
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..20)

ponPortLinkedOnuCounter		1.3.6.1.4.1.10072.2.20.1.1.3.1.1.29
The current number of linked ONUs in this PON port.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..64

ponPortAdminStatus		1.3.6.1.4.1.10072.2.20.1.1.3.1.1.30
The desired state of the PON port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	up(1), down(2)

ponPortReset		1.3.6.1.4.1.10072.2.20.1.1.3.1.1.31
PON interface reset.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noop(1), reset(2)

ponPortWindowRange		1.3.6.1.4.1.10072.2.20.1.1.3.1.1.32
The max window range of ONU register.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), wr20km(2), wr40km(3), wr60km(4)

ponPortDownlinkPolicingEbl		1.3.6.1.4.1.10072.2.20.1.1.3.1.1.33
Config onu downlink-policer enable
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

ponPortAllOnuAlmLevel		1.3.6.1.4.1.10072.2.20.1.1.3.1.1.34
All ONUs alarm-level list.
Status: current	Access: read-only
OBJECT-TYPE
	OnuAlarmLevelList

ponOnuMapTable		1.3.6.1.4.1.10072.2.20.1.1.3.2
table of pon-ONU map
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PonOnuMapEntry

ponOnuMapEntry		1.3.6.1.4.1.10072.2.20.1.1.3.2.1
An entry in the table
Status: current	Access: not-accessible
OBJECT-TYPE
	PonOnuMapEntry

mappingOnuIndex		1.3.6.1.4.1.10072.2.20.1.1.3.2.1.1
index of mapping onu
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..64

onuDevIndex		1.3.6.1.4.1.10072.2.20.1.1.3.2.1.2
device index of this ONU
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..2147483647

onuName		1.3.6.1.4.1.10072.2.20.1.1.3.2.1.3
device name of this ONU
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(255)

ponPerfMonTable		1.3.6.1.4.1.10072.2.20.1.1.3.3
Table of pon performence
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PonPerfMonEntry

ponPerfMonEntry		1.3.6.1.4.1.10072.2.20.1.1.3.3.1
An entry in the table, containing pon performence monitor information .
Status: current	Access: not-accessible
OBJECT-TYPE
	PonPerfMonEntry

ponPerfBER		1.3.6.1.4.1.10072.2.20.1.1.3.3.1.1
byte error rate of specified pon port upstream, UNIT: 10E-6
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ponPerfFER		1.3.6.1.4.1.10072.2.20.1.1.3.3.1.4
frame error rate of specified pon port downstream, UNIT: 10E-6
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ponPerfBerAlmEnable		1.3.6.1.4.1.10072.2.20.1.1.3.3.1.5
The value indicates whether enable pon performence BER alarm
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

ponPerfFerAlmEnable		1.3.6.1.4.1.10072.2.20.1.1.3.3.1.6
The value indicates whether enable pon performence FER alarm
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

ponPerfUpBandwidth		1.3.6.1.4.1.10072.2.20.1.1.3.3.1.7
the value indicates upstream bandwidth on this port
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ponPerfDownBandwidth		1.3.6.1.4.1.10072.2.20.1.1.3.3.1.8
the value indicates downstream bandwidth on this port
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ponHisCtrlTable		1.3.6.1.4.1.10072.2.20.1.1.3.4
Table of pon performence
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PonHisCtrlEntry

ponHisCtrlEntry		1.3.6.1.4.1.10072.2.20.1.1.3.4.1
An entry in the table, containing pon performence monitor information .
Status: current	Access: not-accessible
OBJECT-TYPE
	PonHisCtrlEntry

ponHis15MinuteEnable		1.3.6.1.4.1.10072.2.20.1.1.3.4.1.1
The value indicates whether enable history statistic with interval 15 minutes
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

ponHis24HourEnable		1.3.6.1.4.1.10072.2.20.1.1.3.4.1.2
The value indicates whether enable history statistic with interval 24 hours
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

ponBERThreashold		1.3.6.1.4.1.10072.2.20.1.1.3.5
Ber measurement threshold, the value defination: 0=1e-0=1, 1=1e-1=0.1,......
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..8

ponFERThreashold		1.3.6.1.4.1.10072.2.20.1.1.3.6
Fer measurement threshold, the value defination: 0=1.00e-0=1, 1=1.00e-1=0.1,......
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..10

gwEponPonCtcExt		1.3.6.1.4.1.10072.2.20.1.1.3.7
OBJECT IDENTIFIER

onuAuthEnable		1.3.6.1.4.1.10072.2.20.1.1.4.1
Tok_String
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), auth-new-only(2), auth-all(3)

onuAuthTable		1.3.6.1.4.1.10072.2.20.1.1.4.2
The table of ONU authentication based MAC address.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		OnuAuthEntry

onuAuthEntry		1.3.6.1.4.1.10072.2.20.1.1.4.2.1
An entry in the table
Status: current	Access: not-accessible
OBJECT-TYPE
	OnuAuthEntry

eponBoardIndex		1.3.6.1.4.1.10072.2.20.1.1.4.2.1.1
The epon board index
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

eponPonPortIndex		1.3.6.1.4.1.10072.2.20.1.1.4.2.1.2
PON port index
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

onuAuthIndex		1.3.6.1.4.1.10072.2.20.1.1.4.2.1.3
MAC address index
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

onuAuthMacAddress		1.3.6.1.4.1.10072.2.20.1.1.4.2.1.4
MAC address
Status: current	Access: read-create
OBJECT-TYPE
	MacAddress

onuAuthRowStatus		1.3.6.1.4.1.10072.2.20.1.1.4.2.1.5
This object indicates the status of this entry.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

onuToPonBindingEnable		1.3.6.1.4.1.10072.2.20.1.1.4.3
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

onuAuthModeTable		1.3.6.1.4.1.10072.2.20.1.1.4.4
The table of ONU authentication Mode.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		OnuAuthModeEntry

onuAuthModeEntry		1.3.6.1.4.1.10072.2.20.1.1.4.4.1
An entry in the table
Status: current	Access: not-accessible
OBJECT-TYPE
	OnuAuthModeEntry

onuAuthModeBrdIdx		1.3.6.1.4.1.10072.2.20.1.1.4.4.1.1
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

onuAuthModePonIdx		1.3.6.1.4.1.10072.2.20.1.1.4.4.1.2
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

onuAuthMode		1.3.6.1.4.1.10072.2.20.1.1.4.4.1.3
'macAddr(1)' : based ONU MAC address. 'loid(2)' : based ONU logical ID. 'hybrid(3)' : based both macAddr and loid. 'loidNoPwd(4) : based loid, but not check password. 'hybridNoPwd(5)' : based hybrid, but not check password.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	macAddr(1), loid(2), hybrid(3), loidNoPwd(4), hybridNoPwd(5), disable(6)

onuAuthEnableForPon		1.3.6.1.4.1.10072.2.20.1.1.4.4.1.4
Description
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), auth-new-only(2), auth-all(3)

onuAuthEntryReorganize		1.3.6.1.4.1.10072.2.20.1.1.4.4.1.5
For PonPort
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	organize(1)

onuAuthEntryReorganizeForAll		1.3.6.1.4.1.10072.2.20.1.1.4.9
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	organize(1)

onuAuthLoidTable		1.3.6.1.4.1.10072.2.20.1.1.4.5
The table of ONU authentication based LOID(Logical ONU ID).
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		OnuAuthLoidEntry

onuAuthLoidEntry		1.3.6.1.4.1.10072.2.20.1.1.4.5.1
An entry in the table
Status: current	Access: not-accessible
OBJECT-TYPE
	OnuAuthLoidEntry

onuAuthLoidBrdIdx		1.3.6.1.4.1.10072.2.20.1.1.4.5.1.1
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

onuAuthLoidPonIdx		1.3.6.1.4.1.10072.2.20.1.1.4.5.1.2
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

onuAuthLoidIdx		1.3.6.1.4.1.10072.2.20.1.1.4.5.1.3
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..128

onuAuthLoid		1.3.6.1.4.1.10072.2.20.1.1.4.5.1.4
Tok_String
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(24)

onuAuthLoidPassword		1.3.6.1.4.1.10072.2.20.1.1.4.5.1.5
Tok_String
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(12)

onuAuthLoidDevIdx		1.3.6.1.4.1.10072.2.20.1.1.4.5.1.6
Tok_String
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

onuAuthLoidRowStatus		1.3.6.1.4.1.10072.2.20.1.1.4.5.1.7
This object indicates the status of this entry.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

onuUnauthenticatedTable		1.3.6.1.4.1.10072.2.20.1.1.4.6
The table of unauthenticated ONUs based MAC address.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		OnuAuth1Entry

onuUnauthenticatedEntry		1.3.6.1.4.1.10072.2.20.1.1.4.6.1
An entry in the table
Status: current	Access: not-accessible
OBJECT-TYPE
	OnuAuth1Entry

eponUnauthenticatedBoardIndex		1.3.6.1.4.1.10072.2.20.1.1.4.6.1.1
The epon board index
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

eponUnauthenticatedPonPortIndex		1.3.6.1.4.1.10072.2.20.1.1.4.6.1.2
PON port index
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

onuUnauthenticatedIndex		1.3.6.1.4.1.10072.2.20.1.1.4.6.1.3
MAC address index
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

onuUnauthenticatedMacAddress		1.3.6.1.4.1.10072.2.20.1.1.4.6.1.4
MAC address
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

ponLlidTable		1.3.6.1.4.1.10072.2.20.1.1.5.1
Table of the pon llid information
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PonLlidEntry

ponLlidEntry		1.3.6.1.4.1.10072.2.20.1.1.5.1.1
An entry in the table, containing status or configure information
Status: current	Access: not-accessible
OBJECT-TYPE
	PonLlidEntry

ponLlidIndex		1.3.6.1.4.1.10072.2.20.1.1.5.1.1.1
The pon logic link index
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ponLlidType		1.3.6.1.4.1.10072.2.20.1.1.5.1.1.2
type of pon logic link
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unkown(0), ethlink(1)

ponLlidOltBoard		1.3.6.1.4.1.10072.2.20.1.1.5.1.1.3
The value equals to entPhysicalIndex in ENTITY-MIB
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

ponLlidOltPort		1.3.6.1.4.1.10072.2.20.1.1.5.1.1.4
the pon port id
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

ponLlidOltPortIfIndex		1.3.6.1.4.1.10072.2.20.1.1.5.1.1.5
ifIndex of the olt port
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

ponLlidOnuPortIfIndex		1.3.6.1.4.1.10072.2.20.1.1.5.1.1.6
ifIndex of the onu port
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

ponLlidOnuBoard		1.3.6.1.4.1.10072.2.20.1.1.5.1.1.7
The value indicates board id for this LLID
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

ponLlidOnuPort		1.3.6.1.4.1.10072.2.20.1.1.5.1.1.8
The value indicates onu port for this LLID
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

ponLlidLLID		1.3.6.1.4.1.10072.2.20.1.1.5.1.1.9
the vlaue of LLID
Status: obsolete	Access: read-only
OBJECT-TYPE
	Integer32	1..2147483647

ponLlidIfIndex		1.3.6.1.4.1.10072.2.20.1.1.5.1.1.10
The value equals to ''ifIndex'' in IF-MIB according this object'
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..2147483647

ponLlidUpFixedBW		1.3.6.1.4.1.10072.2.20.1.1.5.1.1.11
upstream fixed bandwidth about this pon port, unit:KBps
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..1000000

ponLlidDownFixedBW		1.3.6.1.4.1.10072.2.20.1.1.5.1.1.12
upstream fixed bandwidth about this pon port, unit:KBps, not support
Status: obsolete	Access: read-write
OBJECT-TYPE
	Integer32	0..1000000

ponLlidDesc		1.3.6.1.4.1.10072.2.20.1.1.5.1.1.13
description of the LLID
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString

ponLlidSurportMacNum		1.3.6.1.4.1.10072.2.20.1.1.5.1.1.14
The value of maximum MAC addresses
Status: deprecated	Access: read-create
OBJECT-TYPE
	Integer32	0..8192

ponLlidOnuMacAddress		1.3.6.1.4.1.10072.2.20.1.1.5.1.1.15
The value indicates and confgure onu MAC address
Status: current	Access: read-create
OBJECT-TYPE
	MacAddress	Size(6)

ponLlidRowStatus		1.3.6.1.4.1.10072.2.20.1.1.5.1.1.16
row status of this entry
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

ponLlidUpBWClass		1.3.6.1.4.1.10072.2.20.1.1.5.1.1.17
upstream class level for this pon port bandwidth allocation
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..7

ponLlidUpDelay		1.3.6.1.4.1.10072.2.20.1.1.5.1.1.18
upstream delay level for this pon port bandwidth allocation
Status: deprecated	Access: read-write
OBJECT-TYPE
	INTEGER	low(1), high(2)

ponLlidUpAssuredBW		1.3.6.1.4.1.10072.2.20.1.1.5.1.1.19
upstream assured bandwidth about this pon port, unit:KBps
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	64..1000000

ponLlidUpBesteffortBW		1.3.6.1.4.1.10072.2.20.1.1.5.1.1.20
upstream best-effort bandwidth about this pon port, unit:KBps
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	64..1000000

ponLlidDownBWClass		1.3.6.1.4.1.10072.2.20.1.1.5.1.1.21
upstream class level for this pon port bandwidth allocation
Status: obsolete	Access: read-write
OBJECT-TYPE
	Integer32	0..7

ponLlidDownDelay		1.3.6.1.4.1.10072.2.20.1.1.5.1.1.22
upstream delay level for this pon port bandwidth allocation
Status: obsolete	Access: read-write
OBJECT-TYPE
	INTEGER	low(1), high(2)

ponLlidDownAssuredBW		1.3.6.1.4.1.10072.2.20.1.1.5.1.1.23
downstream assured bandwidth about this pon port, unit:KBps
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	64..1000000

ponLlidDownBesteffortBW		1.3.6.1.4.1.10072.2.20.1.1.5.1.1.24
downstream best-effort bandwidth about this pon port, unit:KBps
Status: obsolete	Access: read-write
OBJECT-TYPE
	Integer32	64..1000000

ponLlidCtcFecAbility		1.3.6.1.4.1.10072.2.20.1.1.5.1.1.25
FEC ability
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), supported(2), notSupported(3)

ponLlidCtcFecMode		1.3.6.1.4.1.10072.2.20.1.1.5.1.1.26
FEC mode, unknown(1)-initializing, true state not yet known. enable(2)-activate FEC. disable(3)-deactivate FEC.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unknown(1), enable(2), disable(3)

ponLlidCtcEncrypCtrl		1.3.6.1.4.1.10072.2.20.1.1.5.1.1.27
CTC encryption control
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

ponLlidCtcDbaQueSetNum		1.3.6.1.4.1.10072.2.20.1.1.5.1.1.28
DBA queue set number
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..8

ponLlidCtcDbaQueSetCfgStatus		1.3.6.1.4.1.10072.2.20.1.1.5.1.1.29
The Queue sets configuration status, this object value is always 'noop(1)' when read, 'get(2)' will refresh the object of ponLlidCtcDbaQueSetNum and the table of ponLlidCtcDbaQueSetTable, 'set(3)' will config the data, include ponLlidCtcDbaQueSetNum and ponLlidCtcDbaQueSetTable. 'get(2)' and 'set(3) are only write value.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noop(1), get(2), set(3)

ponLlidCtcDbaQueSetTable		1.3.6.1.4.1.10072.2.20.1.1.5.2
Table of the pon llid DBA information
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PonLlidCtcDbaQueSetEntry

ponLlidCtcDbaQueSetEntry		1.3.6.1.4.1.10072.2.20.1.1.5.2.1
CTC DBA entry
Status: current	Access: not-accessible
OBJECT-TYPE
	PonLlidCtcDbaQueSetEntry

ponLlidCtcDbaQueSetIndex		1.3.6.1.4.1.10072.2.20.1.1.5.2.1.1
The DBA queue-sets index
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ponLlidCtcDbaReportBitmap		1.3.6.1.4.1.10072.2.20.1.1.5.2.1.2
bit=0 - queue x report is not present, bit=1 - queue x report is present
Status: current	Access: read-write
OBJECT-TYPE
	BITS	queue0(0), queue1(1), queue2(2), queue3(3), queue4(4), queue5(5), queue6(6), queue7(7)

ponLlidCtcDbaQueue0Threshold		1.3.6.1.4.1.10072.2.20.1.1.5.2.1.3
Queue0 threshold
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..65535

ponLlidCtcDbaQueue1Threshold		1.3.6.1.4.1.10072.2.20.1.1.5.2.1.4
Queue1 threshold
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..65535

ponLlidCtcDbaQueue2Threshold		1.3.6.1.4.1.10072.2.20.1.1.5.2.1.5
Queue2 threshold
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..65535

ponLlidCtcDbaQueue3Threshold		1.3.6.1.4.1.10072.2.20.1.1.5.2.1.6
Queue3 threshold
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..65535

ponLlidCtcDbaQueue4Threshold		1.3.6.1.4.1.10072.2.20.1.1.5.2.1.7
Queue4 threshold
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..65535

ponLlidCtcDbaQueue5Threshold		1.3.6.1.4.1.10072.2.20.1.1.5.2.1.8
Queue5 threshold
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..65535

ponLlidCtcDbaQueue6Threshold		1.3.6.1.4.1.10072.2.20.1.1.5.2.1.9
Queue6 threshold
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..65535

ponLlidCtcDbaQueue7Threshold		1.3.6.1.4.1.10072.2.20.1.1.5.2.1.10
Queue7 threshold
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..65535

onuNewRegSuccess		1.3.6.1.4.1.10072.2.20.1.1.6.1
A new ONU register success.
Status: current	Access: read-write
NOTIFICATION-TYPE

onuReregSuccess		1.3.6.1.4.1.10072.2.20.1.1.6.2
An ONU reregister success.
Status: current	Access: read-write
NOTIFICATION-TYPE

onuNotPresent		1.3.6.1.4.1.10072.2.20.1.1.6.3
An ONU is not present alarm
Status: current	Access: read-write
NOTIFICATION-TYPE

devPowerOff		1.3.6.1.4.1.10072.2.20.1.1.6.4
device Power Off Alarm
Status: current	Access: read-write
NOTIFICATION-TYPE

devPowerOn		1.3.6.1.4.1.10072.2.20.1.1.6.5
device Power On Alarm
Status: current	Access: read-write
NOTIFICATION-TYPE

cfgDataSaveSuccess		1.3.6.1.4.1.10072.2.20.1.1.6.6
saving config data to flash successfully
Status: current	Access: read-write
NOTIFICATION-TYPE

cfgDataSaveFail		1.3.6.1.4.1.10072.2.20.1.1.6.7
saving config data to flash unsuccessfully
Status: current	Access: read-write
NOTIFICATION-TYPE

flashClearSuccess		1.3.6.1.4.1.10072.2.20.1.1.6.8
clear config data successfully
Status: current	Access: read-write
NOTIFICATION-TYPE

flashClearFail		1.3.6.1.4.1.10072.2.20.1.1.6.9
clear config data unsuccessfully
Status: current	Access: read-write
NOTIFICATION-TYPE

softwareUpdateSuccess		1.3.6.1.4.1.10072.2.20.1.1.6.10
update software successfully
Status: current	Access: read-write
NOTIFICATION-TYPE

softwareUpdateFail		1.3.6.1.4.1.10072.2.20.1.1.6.11
update software unsuccessfully
Status: current	Access: read-write
NOTIFICATION-TYPE

firmwareUpdateSuccess		1.3.6.1.4.1.10072.2.20.1.1.6.12
firmware update successfully
Status: current	Access: read-write
NOTIFICATION-TYPE

firmwareUpdateFail		1.3.6.1.4.1.10072.2.20.1.1.6.13
update firmware unsuccessfully
Status: current	Access: read-write
NOTIFICATION-TYPE

cfgDataBackupSuccess		1.3.6.1.4.1.10072.2.20.1.1.6.14
backup configuration data to NMS successfully.
Status: current	Access: read-write
NOTIFICATION-TYPE

cfgDataBackupFail		1.3.6.1.4.1.10072.2.20.1.1.6.15
backup configuration data to NMS unsuccessfully.
Status: current	Access: read-write
NOTIFICATION-TYPE

cfgDataRestoreSuccess		1.3.6.1.4.1.10072.2.20.1.1.6.16
restore configuration data from NMS successfully.
Status: current	Access: read-write
NOTIFICATION-TYPE

cfgDataRestoreFail		1.3.6.1.4.1.10072.2.20.1.1.6.17
restore configuration data from NMS unsuccessfully.
Status: current	Access: read-write
NOTIFICATION-TYPE

autoProtectSwitch		1.3.6.1.4.1.10072.2.20.1.1.6.18
Auto Protect Switch(APS) occurs
Status: current	Access: read-write
NOTIFICATION-TYPE

cpuUsageFactorHigh		1.3.6.1.4.1.10072.2.20.1.1.6.19
high cpu usage factor alarm
Status: current	Access: read-write
NOTIFICATION-TYPE

ponPortBERAlarm		1.3.6.1.4.1.10072.2.20.1.1.6.20
pon port BER alarm
Status: current	Access: read-write
NOTIFICATION-TYPE

ponPortBERAlarmClear		1.3.6.1.4.1.10072.2.20.1.1.6.21
pon port BER alarm clear
Status: current	Access: read-write
NOTIFICATION-TYPE

ponPortFERAlarm		1.3.6.1.4.1.10072.2.20.1.1.6.22
pon port FER alarm
Status: current	Access: read-write
NOTIFICATION-TYPE

ponPortFERAlarmClear		1.3.6.1.4.1.10072.2.20.1.1.6.23
pon port FER alarm clear
Status: current	Access: read-write
NOTIFICATION-TYPE

llidActBWExceeding		1.3.6.1.4.1.10072.2.20.1.1.6.24
llid bandwidth exceed the limit
Status: current	Access: read-write
NOTIFICATION-TYPE

llidActBWExceedingClear		1.3.6.1.4.1.10072.2.20.1.1.6.25
llid bandwidth return to appropriate value
Status: current	Access: read-write
NOTIFICATION-TYPE

devBoardInterted		1.3.6.1.4.1.10072.2.20.1.1.6.26
insert a board
Status: current	Access: read-write
NOTIFICATION-TYPE

devBoardPull		1.3.6.1.4.1.10072.2.20.1.1.6.27
pull a board out
Status: current	Access: read-write
NOTIFICATION-TYPE

powerOffAlarm		1.3.6.1.4.1.10072.2.20.1.1.6.30
power OFF alarm
Status: current	Access: read-write
NOTIFICATION-TYPE

powerOnAlarm		1.3.6.1.4.1.10072.2.20.1.1.6.31
power ON alarm
Status: current	Access: read-write
NOTIFICATION-TYPE

boardTemperatureHigh		1.3.6.1.4.1.10072.2.20.1.1.6.32
board temperature high alarm
Status: current	Access: read-write
NOTIFICATION-TYPE

boardTemperatureHighClear		1.3.6.1.4.1.10072.2.20.1.1.6.33
board temperature high alarm clear
Status: current	Access: read-write
NOTIFICATION-TYPE

ponBoardReset		1.3.6.1.4.1.10072.2.20.1.1.6.34
PON board reset event occur
Status: current	Access: read-write
NOTIFICATION-TYPE

swBoardProtectedSwitch		1.3.6.1.4.1.10072.2.20.1.1.6.35
sw board protected switch event occur
Status: current	Access: read-write
NOTIFICATION-TYPE

ponPortAbnormal		1.3.6.1.4.1.10072.2.20.1.1.6.36
abnormal status on PON port occur
Status: current	Access: read-write
NOTIFICATION-TYPE

onuRegisterConflict		1.3.6.1.4.1.10072.2.20.1.1.6.37
onu register conflict
Status: current	Access: read-write
NOTIFICATION-TYPE

firmwareLoadSuccess		1.3.6.1.4.1.10072.2.20.1.1.6.38
firmware load successfully
Status: current	Access: read-write
NOTIFICATION-TYPE

firmwareLoadFailure		1.3.6.1.4.1.10072.2.20.1.1.6.39
firmware load fail
Status: current	Access: read-write
NOTIFICATION-TYPE

dbaUpdateSuccess		1.3.6.1.4.1.10072.2.20.1.1.6.40
update dba successfully
Status: current	Access: read-write
NOTIFICATION-TYPE

dbaUpdateFailure		1.3.6.1.4.1.10072.2.20.1.1.6.41
update dba faul
Status: current	Access: read-write
NOTIFICATION-TYPE

dbaLoadSuccess		1.3.6.1.4.1.10072.2.20.1.1.6.42
load dba successfully
Status: current	Access: read-write
NOTIFICATION-TYPE

dbaLoadFailure		1.3.6.1.4.1.10072.2.20.1.1.6.43
load dba fail
Status: current	Access: read-write
NOTIFICATION-TYPE

ponToEthLinkdown		1.3.6.1.4.1.10072.2.20.1.1.6.44
.
Status: current	Access: read-write
NOTIFICATION-TYPE

ponToEthLinkup		1.3.6.1.4.1.10072.2.20.1.1.6.45
.
Status: current	Access: read-write
NOTIFICATION-TYPE

onuSoftwareLoadSuccess		1.3.6.1.4.1.10072.2.20.1.1.6.46
load onu software successfully
Status: current	Access: read-write
NOTIFICATION-TYPE

onuSoftwareLoadFailure		1.3.6.1.4.1.10072.2.20.1.1.6.47
load onu software fail
Status: current	Access: read-write
NOTIFICATION-TYPE

ethLinkdown		1.3.6.1.4.1.10072.2.20.1.1.6.54
Ethernet port linkdown alarm.
Status: current	Access: read-write
NOTIFICATION-TYPE

ethLinkup		1.3.6.1.4.1.10072.2.20.1.1.6.55
Ethernet port linkup alarm.
Status: current	Access: read-write
NOTIFICATION-TYPE

bootUpdateSuccess		1.3.6.1.4.1.10072.2.20.1.1.6.56
boot firmware update successfully notification
Status: current	Access: read-write
NOTIFICATION-TYPE

bootUpdateFailure		1.3.6.1.4.1.10072.2.20.1.1.6.57
boot firmware update fail notification
Status: current	Access: read-write
NOTIFICATION-TYPE

batFileBackupSuccess		1.3.6.1.4.1.10072.2.20.1.1.6.58
bat file backup successfully notification
Status: current	Access: read-write
NOTIFICATION-TYPE

batFileBackupFailure		1.3.6.1.4.1.10072.2.20.1.1.6.59
bat file backup fail notification
Status: current	Access: read-write
NOTIFICATION-TYPE

batFileRestoreSuccess		1.3.6.1.4.1.10072.2.20.1.1.6.60
bat file restore successfully notification
Status: current	Access: read-write
NOTIFICATION-TYPE

batFileRestoreFailure		1.3.6.1.4.1.10072.2.20.1.1.6.61
bat file restore fail notification
Status: current	Access: read-write
NOTIFICATION-TYPE

onuRegAuthFailure		1.3.6.1.4.1.10072.2.20.1.1.6.62
Illegal ONU register.
Status: current	Access: read-write
NOTIFICATION-TYPE

deviceColdStart		1.3.6.1.4.1.10072.2.20.1.1.6.63
Only report OLT cold start. this trap is not sent if a devPowerOn trap is sent for the same restart. Implementation of this trap is optional.
Status: current	Access: read-write
NOTIFICATION-TYPE

deviceWarmStart		1.3.6.1.4.1.10072.2.20.1.1.6.64
Only report OLT warm start.
Status: current	Access: read-write
NOTIFICATION-TYPE

deviceExceptionRestart		1.3.6.1.4.1.10072.2.20.1.1.6.65
Only report OLT restart because of exception.
Status: current	Access: read-write
NOTIFICATION-TYPE

ethLoopAlarm		1.3.6.1.4.1.10072.2.20.1.1.6.84
Ethernet port loop alarm.
Status: current	Access: read-write
NOTIFICATION-TYPE

ethLoopAlarmClear		1.3.6.1.4.1.10072.2.20.1.1.6.85
Ethernet port loop clear.
Status: current	Access: read-write
NOTIFICATION-TYPE

onuLoopAlarm		1.3.6.1.4.1.10072.2.20.1.1.6.86
Onu loop alarm.
Status: current	Access: read-write
NOTIFICATION-TYPE

onuLoopAlarmClear		1.3.6.1.4.1.10072.2.20.1.1.6.87
Onu loop clear.
Status: current	Access: read-write
NOTIFICATION-TYPE

backboneEthLinkdown		1.3.6.1.4.1.10072.2.20.1.1.6.88
Ethernet port linkdown alarm.
Status: current	Access: read-write
NOTIFICATION-TYPE

backboneEthLinkup		1.3.6.1.4.1.10072.2.20.1.1.6.89
Ethernet port linkup alarm.
Status: current	Access: read-write
NOTIFICATION-TYPE

boardCpuUsageAlarm		1.3.6.1.4.1.10072.2.20.1.1.6.116
cpu usage factor alarm
Status: current	Access: read-write
NOTIFICATION-TYPE

boardCpuUsageAlarmClear		1.3.6.1.4.1.10072.2.20.1.1.6.117
cpu usage factor alarm clear
Status: current	Access: read-write
NOTIFICATION-TYPE

boardMemoryUsageAlarm		1.3.6.1.4.1.10072.2.20.1.1.6.118
Tok_String
Status: current	Access: read-write
NOTIFICATION-TYPE

boardMemoryUsageAlarmClear		1.3.6.1.4.1.10072.2.20.1.1.6.119
Tok_String
Status: current	Access: read-write
NOTIFICATION-TYPE

ponPortFullAlarm		1.3.6.1.4.1.10072.2.20.1.1.6.132
Tok_String
Status: current	Access: read-write
NOTIFICATION-TYPE

ponPortAbnormalClear		1.3.6.1.4.1.10072.2.20.1.1.6.133
Tok_String
Status: current	Access: read-write
NOTIFICATION-TYPE

ethPortBroadCastFloodControl		1.3.6.1.4.1.10072.2.20.1.1.6.136
Ethernet port broadcast flood alarm.
Status: current	Access: read-write
NOTIFICATION-TYPE

ethPortBroadCastFloodControlClear		1.3.6.1.4.1.10072.2.20.1.1.6.137
Ethernet port broadcast flood alarm clear.
Status: current	Access: read-write
NOTIFICATION-TYPE

sysfileUploadsuccess		1.3.6.1.4.1.10072.2.20.1.1.6.138
Tok_String
Status: current	Access: read-write
NOTIFICATION-TYPE

sysfileUploadfailure		1.3.6.1.4.1.10072.2.20.1.1.6.139
Tok_String
Status: current	Access: read-write
NOTIFICATION-TYPE

sysfileDownloadsuccess		1.3.6.1.4.1.10072.2.20.1.1.6.140
Tok_String
Status: current	Access: read-write
NOTIFICATION-TYPE

sysfileDownloadfailure		1.3.6.1.4.1.10072.2.20.1.1.6.141
Tok_String
Status: current	Access: read-write
NOTIFICATION-TYPE

ponPortLosAlarm		1.3.6.1.4.1.10072.2.20.1.1.6.142
Tok_String
Status: current	Access: read-write
NOTIFICATION-TYPE

ponPortLosAlarmClear		1.3.6.1.4.1.10072.2.20.1.1.6.143
Tok_String
Status: current	Access: read-write
NOTIFICATION-TYPE

ponFWVersionMismatch		1.3.6.1.4.1.10072.2.20.1.1.6.144
Tok_String
Status: current	Access: read-write
NOTIFICATION-TYPE

ponFWVersionMatch		1.3.6.1.4.1.10072.2.20.1.1.6.145
Tok_String
Status: current	Access: read-write
NOTIFICATION-TYPE

ponDBAVersionMismatch		1.3.6.1.4.1.10072.2.20.1.1.6.146
Tok_String
Status: current	Access: read-write
NOTIFICATION-TYPE

ponDBAVersionMatch		1.3.6.1.4.1.10072.2.20.1.1.6.147
Tok_String
Status: current	Access: read-write
NOTIFICATION-TYPE

ponSFPTypeMismatch		1.3.6.1.4.1.10072.2.20.1.1.6.148
Tok_String
Status: current	Access: read-write
NOTIFICATION-TYPE

ponSFPTypeMitch		1.3.6.1.4.1.10072.2.20.1.1.6.149
Tok_String
Status: current	Access: read-write
NOTIFICATION-TYPE

ponPortBRASAlarm		1.3.6.1.4.1.10072.2.20.1.1.6.150
Tok_String
Status: current	Access: read-write
NOTIFICATION-TYPE

ponPortBRASAlarmClear		1.3.6.1.4.1.10072.2.20.1.1.6.151
Tok_String
Status: current	Access: read-write
NOTIFICATION-TYPE

ponPortUpNoTraffic		1.3.6.1.4.1.10072.2.20.1.1.6.152
Tok_String
Status: current	Access: read-write
NOTIFICATION-TYPE

ponPortUpNoTrafficClear		1.3.6.1.4.1.10072.2.20.1.1.6.153
Tok_String
Status: current	Access: read-write
NOTIFICATION-TYPE

onuDeletingNotify		1.3.6.1.4.1.10072.2.20.1.1.6.154
Illegal ONU register.
Status: current	Access: read-write
NOTIFICATION-TYPE

onuMacTableOverFlow		1.3.6.1.4.1.10072.2.20.1.1.6.208
onu mac table over flow.
Status: current	Access: read-write
NOTIFICATION-TYPE

onuMacTableOverFlowClear		1.3.6.1.4.1.10072.2.20.1.1.6.209
onu mac table over flow clear.
Status: current	Access: read-write
NOTIFICATION-TYPE

onuNotPresentAlmLevel		1.3.6.1.4.1.10072.2.20.1.1.7.1
the value indicates an alarm level is set on this event
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..4

devPowerOffAlmLevel		1.3.6.1.4.1.10072.2.20.1.1.7.2
the value indicates an alarm level is set on this event
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..4

ponPortBERAlarmLevel		1.3.6.1.4.1.10072.2.20.1.1.7.3
the value indicates an alarm level is set on this event
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..4

ponPortFERAlarmLevel		1.3.6.1.4.1.10072.2.20.1.1.7.4
the value indicates an alarm level is set on this event
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..4

llidActBWExceedingAlarmLevel		1.3.6.1.4.1.10072.2.20.1.1.7.5
the value indicates an alarm level is set on this event
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..4

powerOffAlarmLevel		1.3.6.1.4.1.10072.2.20.1.1.7.6
the value indicates an alarm level is set on this event
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..4

boardTemperatureHighAlarmLevel		1.3.6.1.4.1.10072.2.20.1.1.7.7
the value indicates an alarm level is set on this event
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..4

devBoardPullAlarmLevel		1.3.6.1.4.1.10072.2.20.1.1.7.8
the value indicates an alarm level is set on this event
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..4

ethLinkdownAlarmLevel		1.3.6.1.4.1.10072.2.20.1.1.7.9
the value indicates an alarm level is set on this event
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..4

devFanAlarmAlarmLevel		1.3.6.1.4.1.10072.2.20.1.1.7.10
the value indicates an alarm level is set on this event
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..4

ethFlrAlarmLevel		1.3.6.1.4.1.10072.2.20.1.1.7.11
the value indicates an alarm level is set on this event
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..4

ethFerAlarmLevel		1.3.6.1.4.1.10072.2.20.1.1.7.12
the value indicates an alarm level is set on this event
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..4

ethTransmittalIntermitAlarmLevel		1.3.6.1.4.1.10072.2.20.1.1.7.13
the value indicates an alarm level is set on this event
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..4

gwEponPonCtcExtOamDiscoveryTiming		1.3.6.1.4.1.10072.2.20.1.1.3.7.1
extended oam discovery timing, unit: ms
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..2550

gwEponPonCtcExtOamCtcOui		1.3.6.1.4.1.10072.2.20.1.1.3.7.2
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(16)

gwEponPonCtcExtOamCtcVer		1.3.6.1.4.1.10072.2.20.1.1.3.7.3
CTC ext-oam version
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..255

gwEponPonCtcEncrypUpdKeyTime		1.3.6.1.4.1.10072.2.20.1.1.3.7.4
Update key time, unit: s
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..255

gwEponPonCtcEncrypNoReplyTimeout		1.3.6.1.4.1.10072.2.20.1.1.3.7.5
No reply timeout, unit: ms
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..2550

gwEponPonCtcEncrypTimingThreshold		1.3.6.1.4.1.10072.2.20.1.1.3.7.6
Encryption timing threshold
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

gwConsoleBaudRate		1.3.6.1.4.1.10072.2.20.1.1.8.1
the baud rate for the system console
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	b300(1), b600(2), b1200(3), b2400(4), b4800(5), b9600(6), b19200(7), b38400(8), b115200(9), b230400(10)

gwConsoleDataBits		1.3.6.1.4.1.10072.2.20.1.1.8.2
the data bits length for the system console
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	b5(5), b6(6), b7(7), b8(8)

gwConsoleStopBitSet		1.3.6.1.4.1.10072.2.20.1.1.8.3
the stop bits for the system console
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	sb1(1), sb2(2)

gwConsoleParitySet		1.3.6.1.4.1.10072.2.20.1.1.8.4
the parity set for the system console
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), even(2), odd(3), space(4)

gwConsoleFlowCtrlSet		1.3.6.1.4.1.10072.2.20.1.1.8.5
the flow control set for the system console
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)