EXTREME-OSPFV3-MIB

File: EXTREME-OSPFV3-MIB.mib (131249 bytes)

Imported modules

SNMPv2-SMI	SNMPv2-TC	SNMPv2-CONF
IF-MIB	INET-ADDRESS-MIB	OSPF-MIB
EXTREME-BASE-MIB

Imported symbols

MODULE-IDENTITY	OBJECT-TYPE	NOTIFICATION-TYPE
mib-2	Counter32	Gauge32
Integer32	Unsigned32	TEXTUAL-CONVENTION
TruthValue	StorageType	RowStatus
MODULE-COMPLIANCE	OBJECT-GROUP	NOTIFICATION-GROUP
InterfaceIndex	InetAddressType	InetAddress
InetAddressPrefixLength	InetAddressIPv6	Metric
BigMetric	Status	HelloRange
DesignatedRouterPriority	extremeAgent

Defined Types

ExtremeOspfv3UpToRefreshIntervalTc
The values one might be able to configure for variables bounded by the Refresh Interval
TEXTUAL-CONVENTION
	Integer32	1..1800

ExtremeOspfv3DeadIntRangeTc
The range, in seconds, of dead interval value.
TEXTUAL-CONVENTION
	Integer32	1..FFFF

ExtremeOspfv3RouterIdTc
A 32-bit, unsigned integer uniquely identifying the router in the Autonomous System. To ensure uniqueness, this may default to the value of one of the router's IPv4 host addresses if IPv4 is configured on the router.
TEXTUAL-CONVENTION
	Unsigned32	0..FFFFFFFF

ExtremeOspfv3AreaIdTc
An OSPFv3 Area Identifier
TEXTUAL-CONVENTION
	Unsigned32	0..FFFFFFFF

ExtremeOspfv3IfInstIdTc
An OSPFv3 interface instance ID
TEXTUAL-CONVENTION
	Integer32	0..255

ExtremeOspfv3AreaEntry
SEQUENCE
	extremeOspfv3AreaId	ExtremeOspfv3AreaIdTc
	extremeOspfv3ImportAsExtern	INTEGER
	extremeOspfv3AreaSpfRuns	Counter32
	extremeOspfv3AreaBdrRtrCount	Gauge32
	extremeOspfv3AreaAsBdrRtrCount	Gauge32
	extremeOspfv3AreaScopeLsaCount	Gauge32
	extremeOspfv3AreaScopeLsaCksumSum	Integer32
	extremeOspfv3AreaSummary	INTEGER
	extremeOspfv3AreaStatus	RowStatus
	extremeOspfv3StubMetric	BigMetric
	extremeOspfv3AreaNssaTranslatorRole	INTEGER
	extremeOspfv3AreaNssaTranslatorState	INTEGER
	extremeOspfv3AreaNssaTranslatorStabInt	Unsigned32
	extremeOspfv3AreaNssaTranslatorEvents	Counter32
	extremeOspfv3AreaStubMetricType	INTEGER

ExtremeOspfv3AsLsdbEntry
SEQUENCE
	extremeOspfv3AsLsdbType	Unsigned32
	extremeOspfv3AsLsdbRouterId	ExtremeOspfv3RouterIdTc
	extremeOspfv3AsLsdbLsid	Unsigned32
	extremeOspfv3AsLsdbSequence	Integer32
	extremeOspfv3AsLsdbAge	Integer32
	extremeOspfv3AsLsdbChecksum	Integer32
	extremeOspfv3AsLsdbAdvertisement	OCTET STRING
	extremeOspfv3AsLsdbTypeKnown	TruthValue

ExtremeOspfv3AreaLsdbEntry
SEQUENCE
	extremeOspfv3AreaLsdbAreaId	ExtremeOspfv3AreaIdTc
	extremeOspfv3AreaLsdbType	Unsigned32
	extremeOspfv3AreaLsdbRouterId	ExtremeOspfv3RouterIdTc
	extremeOspfv3AreaLsdbLsid	Unsigned32
	extremeOspfv3AreaLsdbSequence	Integer32
	extremeOspfv3AreaLsdbAge	Integer32
	extremeOspfv3AreaLsdbChecksum	Integer32
	extremeOspfv3AreaLsdbAdvertisement	OCTET STRING
	extremeOspfv3AreaLsdbTypeKnown	TruthValue

ExtremeOspfv3LinkLsdbEntry
SEQUENCE
	extremeOspfv3LinkLsdbIfIndex	InterfaceIndex
	extremeOspfv3LinkLsdbIfInstId	ExtremeOspfv3IfInstIdTc
	extremeOspfv3LinkLsdbType	Unsigned32
	extremeOspfv3LinkLsdbRouterId	ExtremeOspfv3RouterIdTc
	extremeOspfv3LinkLsdbLsid	Unsigned32
	extremeOspfv3LinkLsdbSequence	Integer32
	extremeOspfv3LinkLsdbAge	Integer32
	extremeOspfv3LinkLsdbChecksum	Integer32
	extremeOspfv3LinkLsdbAdvertisement	OCTET STRING
	extremeOspfv3LinkLsdbTypeKnown	TruthValue

ExtremeOspfv3HostEntry
SEQUENCE
	extremeOspfv3HostAddressType	InetAddressType
	extremeOspfv3HostAddress	InetAddress
	extremeOspfv3HostMetric	Metric
	extremeOspfv3HostStatus	RowStatus
	extremeOspfv3HostAreaID	ExtremeOspfv3AreaIdTc

ExtremeOspfv3IfEntry
SEQUENCE
	extremeOspfv3IfIndex	InterfaceIndex
	extremeOspfv3IfInstId	ExtremeOspfv3IfInstIdTc
	extremeOspfv3IfAreaId	ExtremeOspfv3AreaIdTc
	extremeOspfv3IfType	INTEGER
	extremeOspfv3IfAdminStat	Status
	extremeOspfv3IfRtrPriority	DesignatedRouterPriority
	extremeOspfv3IfTransitDelay	ExtremeOspfv3UpToRefreshIntervalTc
	extremeOspfv3IfRetransInterval	ExtremeOspfv3UpToRefreshIntervalTc
	extremeOspfv3IfHelloInterval	HelloRange
	extremeOspfv3IfRtrDeadInterval	ExtremeOspfv3DeadIntRangeTc
	extremeOspfv3IfPollInterval	Unsigned32
	extremeOspfv3IfState	INTEGER
	extremeOspfv3IfDesignatedRouter	ExtremeOspfv3RouterIdTc
	extremeOspfv3IfBackupDesignatedRouter	ExtremeOspfv3RouterIdTc
	extremeOspfv3IfEvents	Counter32
	extremeOspfv3IfStatus	RowStatus
	extremeOspfv3IfMulticastForwarding	INTEGER
	extremeOspfv3IfDemand	TruthValue
	extremeOspfv3IfMetricValue	Metric
	extremeOspfv3IfLinkScopeLsaCount	Gauge32
	extremeOspfv3IfLinkLsaCksumSum	Integer32
	extremeOspfv3IfDemandNbrProbe	TruthValue
	extremeOspfv3IfDemandNbrProbeRetxLimit	Unsigned32
	extremeOspfv3IfDemandNbrProbeInterval	Unsigned32

ExtremeOspfv3VirtIfEntry
SEQUENCE
	extremeOspfv3VirtIfAreaId	ExtremeOspfv3AreaIdTc
	extremeOspfv3VirtIfNeighbor	ExtremeOspfv3RouterIdTc
	extremeOspfv3VirtIfIndex	InterfaceIndex
	extremeOspfv3VirtIfInstId	ExtremeOspfv3IfInstIdTc
	extremeOspfv3VirtIfTransitDelay	ExtremeOspfv3UpToRefreshIntervalTc
	extremeOspfv3VirtIfRetransInterval	ExtremeOspfv3UpToRefreshIntervalTc
	extremeOspfv3VirtIfHelloInterval	HelloRange
	extremeOspfv3VirtIfRtrDeadInterval	ExtremeOspfv3DeadIntRangeTc
	extremeOspfv3VirtIfState	INTEGER
	extremeOspfv3VirtIfEvents	Counter32
	extremeOspfv3VirtIfStatus	RowStatus
	extremeOspfv3VirtIfLinkScopeLsaCount	Gauge32
	extremeOspfv3VirtIfLinkLsaCksumSum	Integer32

ExtremeOspfv3NbrEntry
SEQUENCE
	extremeOspfv3NbrIfIndex	InterfaceIndex
	extremeOspfv3NbrIfInstId	ExtremeOspfv3IfInstIdTc
	extremeOspfv3NbrRtrId	ExtremeOspfv3RouterIdTc
	extremeOspfv3NbrAddressType	InetAddressType
	extremeOspfv3NbrAddress	InetAddress
	extremeOspfv3NbrOptions	Integer32
	extremeOspfv3NbrPriority	DesignatedRouterPriority
	extremeOspfv3NbrState	INTEGER
	extremeOspfv3NbrEvents	Counter32
	extremeOspfv3NbrLsRetransQLen	Gauge32
	extremeOspfv3NbrHelloSuppressed	TruthValue
	extremeOspfv3NbrIfId	InterfaceIndex
	extremeOspfv3NbrRestartHelperStatus	INTEGER
	extremeOspfv3NbrRestartHelperAge	ExtremeOspfv3UpToRefreshIntervalTc
	extremeOspfv3NbrRestartHelperExitRc	INTEGER

ExtremeOspfv3CfgNbrEntry
SEQUENCE
	extremeOspfv3CfgNbrIfIndex	InterfaceIndex
	extremeOspfv3CfgNbrIfInstId	ExtremeOspfv3IfInstIdTc
	extremeOspfv3CfgNbrAddressType	InetAddressType
	extremeOspfv3CfgNbrAddress	InetAddress
	extremeOspfv3CfgNbrPriority	DesignatedRouterPriority
	extremeOspfv3CfgNbrRtrId	ExtremeOspfv3RouterIdTc
	extremeOspfv3CfgNbrState	INTEGER
	extremeOspfv3CfgNbrStorageType	StorageType
	extremeOspfv3CfgNbrStatus	RowStatus

ExtremeOspfv3VirtNbrEntry
SEQUENCE
	extremeOspfv3VirtNbrArea	ExtremeOspfv3AreaIdTc
	extremeOspfv3VirtNbrRtrId	ExtremeOspfv3RouterIdTc
	extremeOspfv3VirtNbrIfIndex	InterfaceIndex
	extremeOspfv3VirtNbrIfInstId	ExtremeOspfv3IfInstIdTc
	extremeOspfv3VirtNbrAddressType	InetAddressType
	extremeOspfv3VirtNbrAddress	InetAddress
	extremeOspfv3VirtNbrOptions	Integer32
	extremeOspfv3VirtNbrState	INTEGER
	extremeOspfv3VirtNbrEvents	Counter32
	extremeOspfv3VirtNbrLsRetransQLen	Gauge32
	extremeOspfv3VirtNbrHelloSuppressed	TruthValue
	extremeOspfv3VirtNbrIfId	InterfaceIndex
	extremeOspfv3VirtNbrRestartHelperStatus	INTEGER
	extremeOspfv3VirtNbrRestartHelperAge	ExtremeOspfv3UpToRefreshIntervalTc
	extremeOspfv3VirtNbrRestartHelperExitRc	INTEGER

ExtremeOspfv3AreaAggregateEntry
SEQUENCE
	extremeOspfv3AreaAggregateAreaID	ExtremeOspfv3AreaIdTc
	extremeOspfv3AreaAggregateAreaLsdbType	INTEGER
	extremeOspfv3AreaAggregatePrefixType	InetAddressType
	extremeOspfv3AreaAggregatePrefix	InetAddress
	extremeOspfv3AreaAggregatePrefixLength	InetAddressPrefixLength
	extremeOspfv3AreaAggregateStatus	RowStatus
	extremeOspfv3AreaAggregateEffect	INTEGER
	extremeOspfv3AreaAggregateRouteTag	Integer32

Defined Values

extremeOspfv3MIB		1.3.6.1.4.1.1916.1.50
The MIB module to describe OSPF version 3. Copyright (C) The Internet Society (2005). This version of this MIB module is part of RFC XXXX; see the RFC itself for full legal notices.
MODULE-IDENTITY

extremeOspfv3Notifications		1.3.6.1.4.1.1916.1.50.0
OBJECT IDENTIFIER

extremeOspfv3Objects		1.3.6.1.4.1.1916.1.50.1
OBJECT IDENTIFIER

extremeOspfv3Conformance		1.3.6.1.4.1.1916.1.50.2
OBJECT IDENTIFIER

extremeOspfv3GeneralGroup		1.3.6.1.4.1.1916.1.50.1.1
OBJECT IDENTIFIER

extremeOspfv3RouterId		1.3.6.1.4.1.1916.1.50.1.1.1
A 32-bit integer uniquely identifying the router in the Autonomous System. To ensure uniqueness, this may default to the value of one of the router's IPv4 host addresses, represented as a 32-bit unsigned integer, if IPv4 is configured on the router.
Status: current	Access: read-write
OBJECT-TYPE
	ExtremeOspfv3RouterIdTc

extremeOspfv3AdminStat		1.3.6.1.4.1.1916.1.50.1.1.2
The administrative status of OSPFv3 in the router. The value 'enabled' denotes that the OSPFv3 Process is active on at least one interface; 'disabled' disables it on all interfaces.
Status: current	Access: read-write
OBJECT-TYPE
	Status

extremeOspfv3VersionNumber		1.3.6.1.4.1.1916.1.50.1.1.3
The version number of OSPF for IPv6 is 3.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	version3(3)

extremeOspfv3AreaBdrRtrStatus		1.3.6.1.4.1.1916.1.50.1.1.4
A flag to note whether this router is an area border router.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

extremeOspfv3ASBdrRtrStatus		1.3.6.1.4.1.1916.1.50.1.1.5
A flag to note whether this router is configured as an Autonomous System border router.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

extremeOspfv3AsScopeLsaCount		1.3.6.1.4.1.1916.1.50.1.1.6
The number of AS-Scope (e.g. AS-External) link state advertisements in the link state database.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

extremeOspfv3AsScopeLsaCksumSum		1.3.6.1.4.1.1916.1.50.1.1.7
The 32-bit unsigned sum of the LS checksums of the AS-scoped link state advertisements contained in the link state database. This sum can be used to determine if there has been a change in a router's link state database, and to compare the link state database of two routers.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

extremeOspfv3OriginateNewLsas		1.3.6.1.4.1.1916.1.50.1.1.8
The number of new link-state advertisements that have been originated. This number is incremented each time the router originates a new LSA.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

extremeOspfv3RxNewLsas		1.3.6.1.4.1.1916.1.50.1.1.9
The number of link state advertisements received determined to be new instantiations. This number does not include newer instantiations of self-originated link state advertisements.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

extremeOspfv3ExtLsaCount		1.3.6.1.4.1.1916.1.50.1.1.10
The number of External(LS type 0x4005) in the link state database
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

extremeOspfv3ExtAreaLsdbLimit		1.3.6.1.4.1.1916.1.50.1.1.11
The maximum number of non-default AS-external-LSAs entries that can be stored in the link state database. If the value is -1, then there is no limit. When the number of non-default AS-external-LSAs in a router's link-state database reaches extremeOspfv3ExtAreaLsdbLimit, the router enters Overflow state. The router never holds more than extremeOspfv3ExtAreaLsdbLimit non-default AS-external-LSAs in its database. OspfExtAreaLsdbLimit MUST be set identically in all routers attached to the OSPFv3 backbone and/or any regular OSPFv3 area. (i.e., OSPFv3 stub areas and NSSAs are excluded).
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	-1..7FFFFFFF

extremeOspfv3MulticastExtensions		1.3.6.1.4.1.1916.1.50.1.1.12
A Bit Mask indicating whether the router is forwarding IPv6 multicast datagrams based on the algorithms defined in the Multicast Extensions to OSPF. If intraAreaMulticast set, indicates that the router can forward IPv6 multicast datagrams in the router's directly attached areas (called intra-area multicast routing). If interAreaMulticast set, indicates that the router can forward IPv6 multicast datagrams between OSPFv3 areas (called inter-area multicast routing). If interAsMulticast set, indicates that the router can forward IPv6 multicast datagrams between Autonomous Systems (called inter-AS multicast routing). Only certain combinations of bit settings are allowed, namely: - All bits cleared (no multicasting) - intraAreaMulticast only, - intraAreaMulticast and interAreaMulticast, - intraAreaMulticast and interAsMulticast - intraAreaMulticast, interAreaMulticast and interAsMulticast By default, all bits are cleared.
Status: current	Access: read-write
OBJECT-TYPE
	BITS	intraAreaMulticast(0), interAreaMulticast(1), interAsMulticast(2)

extremeOspfv3ExitOverflowInterval		1.3.6.1.4.1.1916.1.50.1.1.13
The number of seconds that, after entering Overflow State, a router will attempt to leave Overflow State. This allows the router to again originate non-default, AS-External-LSAs. When set to 0, the router will not leave Overflow State until restarted.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

extremeOspfv3DemandExtensions		1.3.6.1.4.1.1916.1.50.1.1.14
The router's support for demand routing.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

extremeOspfv3ReferenceBandwidth		1.3.6.1.4.1.1916.1.50.1.1.15
Reference bandwidth in kilobits/second for calculating default interface metrics. The default value is 100,000 KBPS (100 MBPS)
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

extremeOspfv3RestartSupport		1.3.6.1.4.1.1916.1.50.1.1.16
The router's support for OSPF Graceful restart. Options include: no restart support, only planned restarts or both planned and unplanned restarts.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), plannedOnly(2), plannedAndUnplanned(3)

extremeOspfv3RestartInterval		1.3.6.1.4.1.1916.1.50.1.1.17
Configured OSPF Graceful restart timeout interval.
Status: current	Access: read-write
OBJECT-TYPE
	ExtremeOspfv3UpToRefreshIntervalTc

extremeOspfv3RestartStatus		1.3.6.1.4.1.1916.1.50.1.1.18
The current status of OSPF Graceful restart capability.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notRestarting(1), plannedRestart(2), unplannedRestart(3)

extremeOspfv3RestartAge		1.3.6.1.4.1.1916.1.50.1.1.19
Remaining time in current OSPF Graceful restart interval.
Status: current	Access: read-only
OBJECT-TYPE
	ExtremeOspfv3UpToRefreshIntervalTc

extremeOspfv3RestartExitRc		1.3.6.1.4.1.1916.1.50.1.1.20
Describes the outcome of the last attempt at a Graceful restart. none:............no restart has yet been attempted. inProgress:......a restart attempt is currently underway. completed:.......the last restart completed successfully. timedOut:........the last restart timed out. topologyChanged:.the last restart was aborted due to a topology change.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), inProgress(2), completed(3), timedOut(4), topologyChanged(5)

extremeOspfv3NotificationEnable		1.3.6.1.4.1.1916.1.50.1.1.21
This object provides a coarse level of control over the generation of OSPFv3 notifications. If this object is set to true (1), then it enables the generation of OSPFv3 notifications. If it is set to false (2), these notifications are not generated. This object is persistent, and when written, the entity SHOULD save the change to non-volatile storage.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

extremeOspfv3AreaTable		1.3.6.1.4.1.1916.1.50.1.2
Information describing the configured parameters and cumulative statistics of the router's attached areas.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ExtremeOspfv3AreaEntry

extremeOspfv3AreaEntry		1.3.6.1.4.1.1916.1.50.1.2.1
Information describing the configured parameters and cumulative statistics of one of the router's attached areas.
Status: current	Access: not-accessible
OBJECT-TYPE
	ExtremeOspfv3AreaEntry

extremeOspfv3AreaId		1.3.6.1.4.1.1916.1.50.1.2.1.1
A 32-bit integer uniquely identifying an area. Area ID 0 is used for the OSPFv3 backbone.
Status: current	Access: not-accessible
OBJECT-TYPE
	ExtremeOspfv3AreaIdTc

extremeOspfv3ImportAsExtern		1.3.6.1.4.1.1916.1.50.1.2.1.2
Indicates whether an area is a Stub area, NSSA, or standard area. AS-scope LSAs are not imported into Stub Areas or NSSAs. NSSAs import AS-External data as NSSA LSAs which have Area-scope
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	importExternal(1), importNoExternal(2), importNssa(3)

extremeOspfv3AreaSpfRuns		1.3.6.1.4.1.1916.1.50.1.2.1.3
The number of times that the intra-area route table has been calculated using this area's link state database. This is typically done using Dijkstra's algorithm.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

extremeOspfv3AreaBdrRtrCount		1.3.6.1.4.1.1916.1.50.1.2.1.4
The total number of area border routers reachable within this area. This is initially zero, and is calculated in each SPF Pass.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

extremeOspfv3AreaAsBdrRtrCount		1.3.6.1.4.1.1916.1.50.1.2.1.5
The total number of Autonomous System border routers reachable within this area. This is initially zero, and is calculated in each SPF Pass.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

extremeOspfv3AreaScopeLsaCount		1.3.6.1.4.1.1916.1.50.1.2.1.6
The total number of Area-Scope link state advertisements in this area's link state database.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

extremeOspfv3AreaScopeLsaCksumSum		1.3.6.1.4.1.1916.1.50.1.2.1.7
The 32-bit unsigned sum of the Area-Scope link state advertisements' LS checksums contained in this area's link state database. The sum can be used to determine if there has been a change in a router's link state database, and to compare the link-state database of two routers.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

extremeOspfv3AreaSummary		1.3.6.1.4.1.1916.1.50.1.2.1.8
The variable ospfAreaSummary controls the im- port of summary LSAs into stub and NSSA areas. It has no effect on other areas. If it is noAreaSummary, the router will not originate summary LSAs into the stub or NSSA area. It will rely entirely on its default route. If it is sendAreaSummary, the router will both summarize and propagate summary LSAs.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	noAreaSummary(1), sendAreaSummary(2)

extremeOspfv3AreaStatus		1.3.6.1.4.1.1916.1.50.1.2.1.9
This variable controls the status of the entry. The use of RowStatus is covered in more detail in [6].
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

extremeOspfv3StubMetric		1.3.6.1.4.1.1916.1.50.1.2.1.10
The metric value advertised for the default route into Stub and NSSA areas.
Status: current	Access: read-create
OBJECT-TYPE
	BigMetric

extremeOspfv3AreaNssaTranslatorRole		1.3.6.1.4.1.1916.1.50.1.2.1.11
Indicates an NSSA Border router's ability to perform NSSA translation of NSSA-LSAs into AS-External-LSAs.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	always(1), candidate(2)

extremeOspfv3AreaNssaTranslatorState		1.3.6.1.4.1.1916.1.50.1.2.1.12
Indicates if and how an NSSA Border router is performing NSSA translation of NSSA-LSAs into AS-External-LSA's. When this object is set to enabled, the NSSA Border router's extremeOspfv3AreaNssTranslatorRole has been set to always. When this object is set to elected, a candidate NSSA Border router is translating NSSA-LSA's into AS-External-LSA's. When this object is set to disabled, a candidate NSSA Border router is NOT translating NSSA-LSA's into AS-External-LSA's.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	enabled(1), elected(2), disabled(3)

extremeOspfv3AreaNssaTranslatorStabInt		1.3.6.1.4.1.1916.1.50.1.2.1.13
The number of seconds after an elected translator determines its services are no longer required, that it should continue to perform its translation duties.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

extremeOspfv3AreaNssaTranslatorEvents		1.3.6.1.4.1.1916.1.50.1.2.1.14
Indicates the number of Translator State changes that have occurred since the last boot-up.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

extremeOspfv3AreaStubMetricType		1.3.6.1.4.1.1916.1.50.1.2.1.15
This variable displays the type of metric advertised as a default route.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	extremeOspfv3Metric(1), comparableCost(2), nonComparable(3)

extremeOspfv3AsLsdbTable		1.3.6.1.4.1.1916.1.50.1.3
The OSPFv3 Process's AS-Scope Link State Database.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ExtremeOspfv3AsLsdbEntry

extremeOspfv3AsLsdbEntry		1.3.6.1.4.1.1916.1.50.1.3.1
A single AS-Scope Link State Advertisement.
Status: current	Access: not-accessible
OBJECT-TYPE
	ExtremeOspfv3AsLsdbEntry

extremeOspfv3AsLsdbType		1.3.6.1.4.1.1916.1.50.1.3.1.1
The type of the link state advertisement. Each link state type has a separate advertisement format. AS-Scope LSAs not recognized by the router may be stored in the database.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	0..FFFFFFFF

extremeOspfv3AsLsdbRouterId		1.3.6.1.4.1.1916.1.50.1.3.1.2
The 32 bit number that uniquely identifies the originating router in the Autonomous System.
Status: current	Access: not-accessible
OBJECT-TYPE
	ExtremeOspfv3RouterIdTc

extremeOspfv3AsLsdbLsid		1.3.6.1.4.1.1916.1.50.1.3.1.3
The Link State ID is an LS Type Specific field containing a unique identifier; it identifies the piece of the routing domain that is being described by the advertisement. In contrast to OSPFv2, the LSID has no addressing semantics.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

extremeOspfv3AsLsdbSequence		1.3.6.1.4.1.1916.1.50.1.3.1.4
The sequence number field is a signed 32-bit integer. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

extremeOspfv3AsLsdbAge		1.3.6.1.4.1.1916.1.50.1.3.1.5
This field is the age of the link state advertisement in seconds.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

extremeOspfv3AsLsdbChecksum		1.3.6.1.4.1.1916.1.50.1.3.1.6
This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

extremeOspfv3AsLsdbAdvertisement		1.3.6.1.4.1.1916.1.50.1.3.1.7
The entire Link State Advertisement, including its header.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(1..65535)

extremeOspfv3AsLsdbTypeKnown		1.3.6.1.4.1.1916.1.50.1.3.1.8
Indicates whether the LSA type is recognized by this Router.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

extremeOspfv3AreaLsdbTable		1.3.6.1.4.1.1916.1.50.1.4
The OSPFv3 Process's Area-Scope Link State Database.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ExtremeOspfv3AreaLsdbEntry

extremeOspfv3AreaLsdbEntry		1.3.6.1.4.1.1916.1.50.1.4.1
A single Area-Scope Link State Advertisement.
Status: current	Access: not-accessible
OBJECT-TYPE
	ExtremeOspfv3AreaLsdbEntry

extremeOspfv3AreaLsdbAreaId		1.3.6.1.4.1.1916.1.50.1.4.1.1
The 32-bit identifier of the Area from which the LSA was received.
Status: current	Access: not-accessible
OBJECT-TYPE
	ExtremeOspfv3AreaIdTc

extremeOspfv3AreaLsdbType		1.3.6.1.4.1.1916.1.50.1.4.1.2
The type of the link state advertisement. Each link state type has a separate advertisement format. Area-Scope LSAs unrecognized by the router are also stored in this database.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	0..FFFFFFFF

extremeOspfv3AreaLsdbRouterId		1.3.6.1.4.1.1916.1.50.1.4.1.3
The 32-bit number that uniquely identifies the originating router in the Autonomous System.
Status: current	Access: not-accessible
OBJECT-TYPE
	ExtremeOspfv3RouterIdTc

extremeOspfv3AreaLsdbLsid		1.3.6.1.4.1.1916.1.50.1.4.1.4
The Link State ID is an LS Type Specific field containing a unique identifier; it identifies the piece of the routing domain that is being described by the advertisement. In contrast to OSPFv2, the LSID has no addressing semantics.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

extremeOspfv3AreaLsdbSequence		1.3.6.1.4.1.1916.1.50.1.4.1.5
The sequence number field is a signed 32-bit integer. It is used to detect old and dupli- cate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

extremeOspfv3AreaLsdbAge		1.3.6.1.4.1.1916.1.50.1.4.1.6
This field is the age of the link state advertisement in seconds.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

extremeOspfv3AreaLsdbChecksum		1.3.6.1.4.1.1916.1.50.1.4.1.7
This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

extremeOspfv3AreaLsdbAdvertisement		1.3.6.1.4.1.1916.1.50.1.4.1.8
The entire Link State Advertisement, including its header.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(1..65535)

extremeOspfv3AreaLsdbTypeKnown		1.3.6.1.4.1.1916.1.50.1.4.1.9
Indicates whether the LSA type is recognized by this Router.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

extremeOspfv3LinkLsdbTable		1.3.6.1.4.1.1916.1.50.1.5
The OSPFv3 Process's Link-Scope Link State Database.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ExtremeOspfv3LinkLsdbEntry

extremeOspfv3LinkLsdbEntry		1.3.6.1.4.1.1916.1.50.1.5.1
A single Link-Scope Link State Advertisement.
Status: current	Access: not-accessible
OBJECT-TYPE
	ExtremeOspfv3LinkLsdbEntry

extremeOspfv3LinkLsdbIfIndex		1.3.6.1.4.1.1916.1.50.1.5.1.1
The identifier of the link from which the LSA was received.
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndex

extremeOspfv3LinkLsdbIfInstId		1.3.6.1.4.1.1916.1.50.1.5.1.2
The identifier of the interface instance from which the LSA was received.
Status: current	Access: not-accessible
OBJECT-TYPE
	ExtremeOspfv3IfInstIdTc

extremeOspfv3LinkLsdbType		1.3.6.1.4.1.1916.1.50.1.5.1.3
The type of the link state advertisement. Each link state type has a separate advertisement format. Link-Scope LSAs unrecognized by the router are also stored in this database.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	0..FFFFFFFF

extremeOspfv3LinkLsdbRouterId		1.3.6.1.4.1.1916.1.50.1.5.1.4
The 32 bit number that uniquely identifies the originating router in the Autonomous System.
Status: current	Access: not-accessible
OBJECT-TYPE
	ExtremeOspfv3RouterIdTc

extremeOspfv3LinkLsdbLsid		1.3.6.1.4.1.1916.1.50.1.5.1.5
The Link State ID is an LS Type Specific field containing a unique identifier; it identifies the piece of the routing domain that is being described by the advertisement. In contrast to OSPFv2, the LSID has no addressing semantics.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

extremeOspfv3LinkLsdbSequence		1.3.6.1.4.1.1916.1.50.1.5.1.6
The sequence number field is a signed 32-bit integer. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

extremeOspfv3LinkLsdbAge		1.3.6.1.4.1.1916.1.50.1.5.1.7
This field is the age of the link state advertisement in seconds.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

extremeOspfv3LinkLsdbChecksum		1.3.6.1.4.1.1916.1.50.1.5.1.8
This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

extremeOspfv3LinkLsdbAdvertisement		1.3.6.1.4.1.1916.1.50.1.5.1.9
The entire Link State Advertisement, including its header.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(1..65535)

extremeOspfv3LinkLsdbTypeKnown		1.3.6.1.4.1.1916.1.50.1.5.1.10
Indicates whether the LSA type is recognized by this Router.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

extremeOspfv3HostTable		1.3.6.1.4.1.1916.1.50.1.6
The list of Hosts, and their metrics, that the router will advertise as host routes.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ExtremeOspfv3HostEntry

extremeOspfv3HostEntry		1.3.6.1.4.1.1916.1.50.1.6.1
A metric to be advertised when a given host is reachable.
Status: current	Access: not-accessible
OBJECT-TYPE
	ExtremeOspfv3HostEntry

extremeOspfv3HostAddressType		1.3.6.1.4.1.1916.1.50.1.6.1.1
The address type of extremeOspfv3HostAddress. Only IPv6 addresses without zone index are expected.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddressType

extremeOspfv3HostAddress		1.3.6.1.4.1.1916.1.50.1.6.1.2
The IPv6 Address of the Host. Must be a Global address.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddress	Size(16)

extremeOspfv3HostMetric		1.3.6.1.4.1.1916.1.50.1.6.1.3
The Metric to be advertised.
Status: current	Access: read-create
OBJECT-TYPE
	Metric

extremeOspfv3HostStatus		1.3.6.1.4.1.1916.1.50.1.6.1.4
This variable controls the status of the entry. The use of RowStatus is covered in more detail in [6].
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

extremeOspfv3HostAreaID		1.3.6.1.4.1.1916.1.50.1.6.1.5
The Area the Host Entry is to be found within. By default, the area that a subsuming OSPFv3 interface is in, or Area 0
Status: current	Access: read-create
OBJECT-TYPE
	ExtremeOspfv3AreaIdTc

extremeOspfv3IfTable		1.3.6.1.4.1.1916.1.50.1.7
The OSPFv3 Interface Table describes the interfaces from the viewpoint of OSPFv3.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ExtremeOspfv3IfEntry

extremeOspfv3IfEntry		1.3.6.1.4.1.1916.1.50.1.7.1
The OSPFv3 Interface Entry describes one interface from the viewpoint of OSPFv3.
Status: current	Access: not-accessible
OBJECT-TYPE
	ExtremeOspfv3IfEntry

extremeOspfv3IfIndex		1.3.6.1.4.1.1916.1.50.1.7.1.1
The interface index of this OSPFv3 interface. It corresponds to the interface index of the IPv6 interface on which OSPFv3 is configured.
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndex

extremeOspfv3IfInstId		1.3.6.1.4.1.1916.1.50.1.7.1.2
Enables multiple interface instances of OSPFv3 to be run over a single link. Each protocol instance would be assigned a separate ID. This ID has local link significance only.
Status: current	Access: not-accessible
OBJECT-TYPE
	ExtremeOspfv3IfInstIdTc

extremeOspfv3IfAreaId		1.3.6.1.4.1.1916.1.50.1.7.1.3
A 32-bit integer uniquely identifying the area to which the interface connects. Area ID 0 is used for the OSPFv3 backbone.
Status: current	Access: read-create
OBJECT-TYPE
	ExtremeOspfv3AreaIdTc

extremeOspfv3IfType		1.3.6.1.4.1.1916.1.50.1.7.1.4
The OSPFv3 interface type.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	broadcast(1), nbma(2), pointToPoint(3), pointToMultipoint(5)

extremeOspfv3IfAdminStat		1.3.6.1.4.1.1916.1.50.1.7.1.5
The OSPFv3 interface's administrative status. The value formed on the interface, and the interface will be advertised as an internal route to some area. The value 'disabled' denotes that the interface is external to OSPFv3.
Status: current	Access: read-create
OBJECT-TYPE
	Status

extremeOspfv3IfRtrPriority		1.3.6.1.4.1.1916.1.50.1.7.1.6
The priority of this interface. Used in multi-access networks, this field is used in the designated router election algorithm. The value 0 signifies that the router is not eligible to become the designated router on this particular network. In the event of a tie in this value, routers will use their Router ID as a tie breaker.
Status: current	Access: read-create
OBJECT-TYPE
	DesignatedRouterPriority

extremeOspfv3IfTransitDelay		1.3.6.1.4.1.1916.1.50.1.7.1.7
The estimated number of seconds it takes to transmit a link state update packet over this interface.
Status: current	Access: read-create
OBJECT-TYPE
	ExtremeOspfv3UpToRefreshIntervalTc

extremeOspfv3IfRetransInterval		1.3.6.1.4.1.1916.1.50.1.7.1.8
The number of seconds between link state advertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database description and link state request packets.
Status: current	Access: read-create
OBJECT-TYPE
	ExtremeOspfv3UpToRefreshIntervalTc

extremeOspfv3IfHelloInterval		1.3.6.1.4.1.1916.1.50.1.7.1.9
The length of time, in seconds, between the Hello packets that the router sends on the interface. This value must be the same for all routers attached to a common network.
Status: current	Access: read-create
OBJECT-TYPE
	HelloRange

extremeOspfv3IfRtrDeadInterval		1.3.6.1.4.1.1916.1.50.1.7.1.10
The number of seconds that a router's Hello packets have not been seen before its neighbors declare the router down on the interface. This should be some multiple of the Hello interval. This value must be the same for all routers attached to a common network.
Status: current	Access: read-create
OBJECT-TYPE
	ExtremeOspfv3DeadIntRangeTc

extremeOspfv3IfPollInterval		1.3.6.1.4.1.1916.1.50.1.7.1.11
The larger time interval, in seconds, between the Hello packets sent to an inactive non-broadcast multi-access neighbor.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

extremeOspfv3IfState		1.3.6.1.4.1.1916.1.50.1.7.1.12
The OSPFv3 Interface State.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	down(1), loopback(2), waiting(3), pointToPoint(4), designatedRouter(5), backupDesignatedRouter(6), otherDesignatedRouter(7)

extremeOspfv3IfDesignatedRouter		1.3.6.1.4.1.1916.1.50.1.7.1.13
The Router ID of the Designated Router.
Status: current	Access: read-only
OBJECT-TYPE
	ExtremeOspfv3RouterIdTc

extremeOspfv3IfBackupDesignatedRouter		1.3.6.1.4.1.1916.1.50.1.7.1.14
The Router ID of the Backup Designated Router.
Status: current	Access: read-only
OBJECT-TYPE
	ExtremeOspfv3RouterIdTc

extremeOspfv3IfEvents		1.3.6.1.4.1.1916.1.50.1.7.1.15
The number of times this OSPF interface has changed its state, or an error has occurred.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

extremeOspfv3IfStatus		1.3.6.1.4.1.1916.1.50.1.7.1.16
This variable controls the status of the entry. The use of RowStatus is covered in more detail in [6].
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

extremeOspfv3IfMulticastForwarding		1.3.6.1.4.1.1916.1.50.1.7.1.17
The way multicasts should forwarded on this interface; not forwarded, forwarded as data link multicasts, or forwarded as data link unicasts. Data link multicasting is not meaningful on point to point and NBMA interfaces, and setting extremeOspfv3MulticastForwarding to 0 effectively disables all multicast forwarding.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	blocked(1), multicast(2), unicast(3)

extremeOspfv3IfDemand		1.3.6.1.4.1.1916.1.50.1.7.1.18
Indicates whether Demand OSPFv3 procedures (hello suppression to FULL neighbors and setting the DoNotAge flag on propagated LSAs) should be performed on this interface.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

extremeOspfv3IfMetricValue		1.3.6.1.4.1.1916.1.50.1.7.1.19
The metric assigned to this interface. The default value of the Metric is Reference Bandwidth / ifSpeed. The value of the reference bandwidth is configured by the extremeOspfv3ReferenceBandwidth object.
Status: current	Access: read-create
OBJECT-TYPE
	Metric

extremeOspfv3IfLinkScopeLsaCount		1.3.6.1.4.1.1916.1.50.1.7.1.20
The total number of Link-Scope link state advertisements in this link's link state database.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

extremeOspfv3IfLinkLsaCksumSum		1.3.6.1.4.1.1916.1.50.1.7.1.21
The 32-bit unsigned sum of the Link-Scope link state advertisements' LS checksums contained in this link's link state database. The sum can be used to determine if there has been a change in a router's link state database, and to compare the link state database of two routers.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

extremeOspfv3IfDemandNbrProbe		1.3.6.1.4.1.1916.1.50.1.7.1.22
Indicates whether or not neighbor probing is enabled to determine whether or not the neighbor is inactive. Neighbor probing is disabled by default.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

extremeOspfv3IfDemandNbrProbeRetxLimit		1.3.6.1.4.1.1916.1.50.1.7.1.23
The number of consecutive LSA retransmissions before the neighbor is deemed inactive and the neighbor adjacency is brought down.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

extremeOspfv3IfDemandNbrProbeInterval		1.3.6.1.4.1.1916.1.50.1.7.1.24
Defines how often the neighbor will be probed.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

extremeOspfv3VirtIfTable		1.3.6.1.4.1.1916.1.50.1.8
Information about this router's virtual interfaces.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ExtremeOspfv3VirtIfEntry

extremeOspfv3VirtIfEntry		1.3.6.1.4.1.1916.1.50.1.8.1
Information about a single Virtual Interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	ExtremeOspfv3VirtIfEntry

extremeOspfv3VirtIfAreaId		1.3.6.1.4.1.1916.1.50.1.8.1.1
The Transit Area that the Virtual Link traverses. By definition, this is not Area 0
Status: current	Access: not-accessible
OBJECT-TYPE
	ExtremeOspfv3AreaIdTc

extremeOspfv3VirtIfNeighbor		1.3.6.1.4.1.1916.1.50.1.8.1.2
The Router ID of the Virtual Neighbor.
Status: current	Access: not-accessible
OBJECT-TYPE
	ExtremeOspfv3RouterIdTc

extremeOspfv3VirtIfIndex		1.3.6.1.4.1.1916.1.50.1.8.1.3
The interface index assigned to this OSPFv3 virtual interface. It is advertised in Hello's sent over the virtal link and in the router's router-LSAs.
Status: current	Access: read-create
OBJECT-TYPE
	InterfaceIndex

extremeOspfv3VirtIfInstId		1.3.6.1.4.1.1916.1.50.1.8.1.4
Specifies the interface instance ID to be used for the virtual interface. This ID has local link significance only.
Status: current	Access: read-create
OBJECT-TYPE
	ExtremeOspfv3IfInstIdTc

extremeOspfv3VirtIfTransitDelay		1.3.6.1.4.1.1916.1.50.1.8.1.5
The estimated number of seconds it takes to transmit a link state update packet over this interface.
Status: current	Access: read-create
OBJECT-TYPE
	ExtremeOspfv3UpToRefreshIntervalTc

extremeOspfv3VirtIfRetransInterval		1.3.6.1.4.1.1916.1.50.1.8.1.6
The number of seconds between link state advertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database description and link state request packets. This value should be well over the expected round-trip time.
Status: current	Access: read-create
OBJECT-TYPE
	ExtremeOspfv3UpToRefreshIntervalTc

extremeOspfv3VirtIfHelloInterval		1.3.6.1.4.1.1916.1.50.1.8.1.7
The length of time, in seconds, between the Hello packets that the router sends on the interface. This value must be the same for the virtual neighbor.
Status: current	Access: read-create
OBJECT-TYPE
	HelloRange

extremeOspfv3VirtIfRtrDeadInterval		1.3.6.1.4.1.1916.1.50.1.8.1.8
The number of seconds that a router's Hello packets have not been seen before its neighbors declare the router down. This should be some multiple of the Hello interval. This value must be the same for the virtual neighbor.
Status: current	Access: read-create
OBJECT-TYPE
	ExtremeOspfv3DeadIntRangeTc

extremeOspfv3VirtIfState		1.3.6.1.4.1.1916.1.50.1.8.1.9
OSPF virtual interface states. The same encoding as the ospfV3IfTable is used.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	down(1), pointToPoint(4)

extremeOspfv3VirtIfEvents		1.3.6.1.4.1.1916.1.50.1.8.1.10
The number of state changes or error events on this Virtual Link
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

extremeOspfv3VirtIfStatus		1.3.6.1.4.1.1916.1.50.1.8.1.11
This variable controls the status of the entry. The use of RowStatus is covered in more detail in [6].
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

extremeOspfv3VirtIfLinkScopeLsaCount		1.3.6.1.4.1.1916.1.50.1.8.1.12
The total number of Link-Scope link state advertisements in this virtual link's link state database.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

extremeOspfv3VirtIfLinkLsaCksumSum		1.3.6.1.4.1.1916.1.50.1.8.1.13
The 32-bit unsigned sum of the Link-Scope link-state advertisements' LS checksums contained in this virtual link's link-state database. The sum can be used to determine if there has been a change in a router's link state database, and to compare the link state database of two routers.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

extremeOspfv3NbrTable		1.3.6.1.4.1.1916.1.50.1.9
A table of non-virtual neighbor information.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ExtremeOspfv3NbrEntry

extremeOspfv3NbrEntry		1.3.6.1.4.1.1916.1.50.1.9.1
The information regarding a single neighbor.
Status: current	Access: not-accessible
OBJECT-TYPE
	ExtremeOspfv3NbrEntry

extremeOspfv3NbrIfIndex		1.3.6.1.4.1.1916.1.50.1.9.1.1
The local link ID of the link over which the neighbor can be reached.
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndex

extremeOspfv3NbrIfInstId		1.3.6.1.4.1.1916.1.50.1.9.1.2
Interface instance over which the neighbor can be reached. This ID has local link significance only.
Status: current	Access: not-accessible
OBJECT-TYPE
	ExtremeOspfv3IfInstIdTc

extremeOspfv3NbrRtrId		1.3.6.1.4.1.1916.1.50.1.9.1.3
A 32-bit integer uniquely identifying the neighboring router in the Autonomous System.
Status: current	Access: not-accessible
OBJECT-TYPE
	ExtremeOspfv3RouterIdTc

extremeOspfv3NbrAddressType		1.3.6.1.4.1.1916.1.50.1.9.1.4
The address type of extremeOspfv3NbrAddress. Only IPv6 addresses without zone index are expected.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddressType

extremeOspfv3NbrAddress		1.3.6.1.4.1.1916.1.50.1.9.1.5
The IPv6 address of the neighbor associated with the local link.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddress	Size(16)

extremeOspfv3NbrOptions		1.3.6.1.4.1.1916.1.50.1.9.1.6
A Bit Mask corresponding to the neighbor's options field.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

extremeOspfv3NbrPriority		1.3.6.1.4.1.1916.1.50.1.9.1.7
The priority of this neighbor in the designated router election algorithm. The value 0 signifies that the neighbor is not eligible to become the designated router on this particular network.
Status: current	Access: read-only
OBJECT-TYPE
	DesignatedRouterPriority

extremeOspfv3NbrState		1.3.6.1.4.1.1916.1.50.1.9.1.8
The State of the relationship with this Neighbor.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	down(1), attempt(2), init(3), twoWay(4), exchangeStart(5), exchange(6), loading(7), full(8)

extremeOspfv3NbrEvents		1.3.6.1.4.1.1916.1.50.1.9.1.9
The number of times this neighbor relationship has changed state, or an error has occurred.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

extremeOspfv3NbrLsRetransQLen		1.3.6.1.4.1.1916.1.50.1.9.1.10
The current length of the retransmission queue.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

extremeOspfv3NbrHelloSuppressed		1.3.6.1.4.1.1916.1.50.1.9.1.11
Indicates whether Hellos are being suppressed to the neighbor
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

extremeOspfv3NbrIfId		1.3.6.1.4.1.1916.1.50.1.9.1.12
The interface ID that the neighbor advertises in its Hello Packets on this link, that is, the neighbor's local interface index.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

extremeOspfv3NbrRestartHelperStatus		1.3.6.1.4.1.1916.1.50.1.9.1.13
Indicates whether the router is acting as a Graceful restart helper for the neighbor.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notHelping(1), helping(2)

extremeOspfv3NbrRestartHelperAge		1.3.6.1.4.1.1916.1.50.1.9.1.14
Remaining time in current OSPF Graceful restart interval, if the router is acting as a restart helper for the neighbor.
Status: current	Access: read-only
OBJECT-TYPE
	ExtremeOspfv3UpToRefreshIntervalTc

extremeOspfv3NbrRestartHelperExitRc		1.3.6.1.4.1.1916.1.50.1.9.1.15
Describes the outcome of the last attempt at acting as a Graceful restart helper for the neighbor. none:............no restart has yet been attempted. inProgress:......a restart attempt is currently underway. completed:.......the last restart completed successfully. timedOut:........the last restart timed out. topologyChanged:.the last restart was aborted due to a topology change.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), inProgress(2), completed(3), timedOut(4), topologyChanged(5)

extremeOspfv3CfgNbrTable		1.3.6.1.4.1.1916.1.50.1.10
A table of configured non-virtual neighbor information and neighbors dynamically discovered by lower-level protocols such as Inverse Neighbor Discovery.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ExtremeOspfv3CfgNbrEntry

extremeOspfv3CfgNbrEntry		1.3.6.1.4.1.1916.1.50.1.10.1
The information regarding a single configured neighbor or neighbor discovered by lower-level protocols such as Inverse Neighbor Discovery.
Status: current	Access: not-accessible
OBJECT-TYPE
	ExtremeOspfv3CfgNbrEntry

extremeOspfv3CfgNbrIfIndex		1.3.6.1.4.1.1916.1.50.1.10.1.1
The local link ID of the link over which the neighbor can be reached.
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndex

extremeOspfv3CfgNbrIfInstId		1.3.6.1.4.1.1916.1.50.1.10.1.2
Interface instance over which the neighbor can be reached. This ID has local link significance only.
Status: current	Access: not-accessible
OBJECT-TYPE
	ExtremeOspfv3IfInstIdTc

extremeOspfv3CfgNbrAddressType		1.3.6.1.4.1.1916.1.50.1.10.1.3
The address type of extremeOspfv3NbrAddress. Only IPv6 addresses without zone index are expected.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddressType

extremeOspfv3CfgNbrAddress		1.3.6.1.4.1.1916.1.50.1.10.1.4
The IPv6 address of the neighbor associated with the local link.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddress	Size(16)

extremeOspfv3CfgNbrPriority		1.3.6.1.4.1.1916.1.50.1.10.1.5
The priority of this neighbor in the designated router election algorithm. The value 0 signifies that the neighbor is not eligible to become the designated router on this particular network.
Status: current	Access: read-create
OBJECT-TYPE
	DesignatedRouterPriority

extremeOspfv3CfgNbrRtrId		1.3.6.1.4.1.1916.1.50.1.10.1.6
A 32-bit integer uniquely identifying the neighboring router in the Autonomous System. A value of 0 is returned until a Hello is received from the configured neighbor.
Status: current	Access: read-only
OBJECT-TYPE
	ExtremeOspfv3RouterIdTc

extremeOspfv3CfgNbrState		1.3.6.1.4.1.1916.1.50.1.10.1.7
The State of the relationship with this Neighbor.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	down(1), attempt(2), init(3), twoWay(4), exchangeStart(5), exchange(6), loading(7), full(8)

extremeOspfv3CfgNbrStorageType		1.3.6.1.4.1.1916.1.50.1.10.1.8
The storage type for this conceptual row. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row. Manually configured entries will have a storage type of nonVolatile while entries dynamically created as a result of a lower-level protocol such as Inverse Neighbor Discovery will have a storage type of volatile.
Status: current	Access: read-create
OBJECT-TYPE
	StorageType

extremeOspfv3CfgNbrStatus		1.3.6.1.4.1.1916.1.50.1.10.1.9
This variable controls the status of the entry. The use of RowStatus is covered in more detail in [6].
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

extremeOspfv3VirtNbrTable		1.3.6.1.4.1.1916.1.50.1.11
A table of virtual neighbor information.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ExtremeOspfv3VirtNbrEntry

extremeOspfv3VirtNbrEntry		1.3.6.1.4.1.1916.1.50.1.11.1
Virtual neighbor information.
Status: current	Access: not-accessible
OBJECT-TYPE
	ExtremeOspfv3VirtNbrEntry

extremeOspfv3VirtNbrArea		1.3.6.1.4.1.1916.1.50.1.11.1.1
The Transit Area Identifier.
Status: current	Access: not-accessible
OBJECT-TYPE
	ExtremeOspfv3AreaIdTc

extremeOspfv3VirtNbrRtrId		1.3.6.1.4.1.1916.1.50.1.11.1.2
A 32-bit integer uniquely identifying the neighboring router in the Autonomous System.
Status: current	Access: not-accessible
OBJECT-TYPE
	ExtremeOspfv3RouterIdTc

extremeOspfv3VirtNbrIfIndex		1.3.6.1.4.1.1916.1.50.1.11.1.3
The local interface ID for the virtual link over which the neighbor can be reached.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

extremeOspfv3VirtNbrIfInstId		1.3.6.1.4.1.1916.1.50.1.11.1.4
The interface instance for the virtual link over which the neighbor can be reached.
Status: current	Access: read-only
OBJECT-TYPE
	ExtremeOspfv3IfInstIdTc

extremeOspfv3VirtNbrAddressType		1.3.6.1.4.1.1916.1.50.1.11.1.5
The address type of extremeOspfv3VirtNbrAddress. Only IPv6 addresses without zone index are expected.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddressType

extremeOspfv3VirtNbrAddress		1.3.6.1.4.1.1916.1.50.1.11.1.6
The IPv6 address advertised by this Virtual Neighbor. It must be a Global scope address.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddress	Size(16)

extremeOspfv3VirtNbrOptions		1.3.6.1.4.1.1916.1.50.1.11.1.7
A Bit Mask corresponding to the neighbor's options field.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

extremeOspfv3VirtNbrState		1.3.6.1.4.1.1916.1.50.1.11.1.8
The state of the Virtual Neighbor Relationship.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	down(1), attempt(2), init(3), twoWay(4), exchangeStart(5), exchange(6), loading(7), full(8)

extremeOspfv3VirtNbrEvents		1.3.6.1.4.1.1916.1.50.1.11.1.9
The number of times this virtual link has changed its state, or an error has occurred.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

extremeOspfv3VirtNbrLsRetransQLen		1.3.6.1.4.1.1916.1.50.1.11.1.10
The current length of the retransmission queue.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

extremeOspfv3VirtNbrHelloSuppressed		1.3.6.1.4.1.1916.1.50.1.11.1.11
Indicates whether Hellos are being suppressed to the neighbor
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

extremeOspfv3VirtNbrIfId		1.3.6.1.4.1.1916.1.50.1.11.1.12
The interface ID that the neighbor advertises in its Hello Packets on this virtual link, that is, the neighbor's local interface ID.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

extremeOspfv3VirtNbrRestartHelperStatus		1.3.6.1.4.1.1916.1.50.1.11.1.13
Indicates whether the router is acting as a Graceful restart helper for the neighbor.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notHelping(1), helping(2)

extremeOspfv3VirtNbrRestartHelperAge		1.3.6.1.4.1.1916.1.50.1.11.1.14
Remaining time in current OSPF Graceful restart interval, if the router is acting as a restart helper for the neighbor.
Status: current	Access: read-only
OBJECT-TYPE
	ExtremeOspfv3UpToRefreshIntervalTc

extremeOspfv3VirtNbrRestartHelperExitRc		1.3.6.1.4.1.1916.1.50.1.11.1.15
Describes the outcome of the last attempt at acting as a Graceful restart helper for the neighbor. none:............no restart has yet been attempted. inProgress:......a restart attempt is currently underway. completed:.......the last restart completed successfully. timedOut:........the last restart timed out. topologyChanged:.the last restart was aborted due to a topology change.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(1), inProgress(2), completed(3), timedOut(4), topologyChanged(5)

extremeOspfv3AreaAggregateTable		1.3.6.1.4.1.1916.1.50.1.12
A range of IPv6 prefixes specified by a prefix/prefix length pair. Note that if ranges are configured such that one range subsumes another range the most specific match is the preferred one.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ExtremeOspfv3AreaAggregateEntry

extremeOspfv3AreaAggregateEntry		1.3.6.1.4.1.1916.1.50.1.12.1
A range of IPv6 prefixes specified by a prefix/prefix length pair. Note that if ranges are configured such that one range subsumes another range the most specific match is the preferred one.
Status: current	Access: not-accessible
OBJECT-TYPE
	ExtremeOspfv3AreaAggregateEntry

extremeOspfv3AreaAggregateAreaID		1.3.6.1.4.1.1916.1.50.1.12.1.1
The Area the Address Aggregate is to be found within.
Status: current	Access: not-accessible
OBJECT-TYPE
	ExtremeOspfv3AreaIdTc

extremeOspfv3AreaAggregateAreaLsdbType		1.3.6.1.4.1.1916.1.50.1.12.1.2
The type of the Address Aggregate. This field specifies the Area Lsdb type that this Address Aggregate applies to.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	interAreaPrefixLsa(8195), nssaExternalLsa(8199)

extremeOspfv3AreaAggregatePrefixType		1.3.6.1.4.1.1916.1.50.1.12.1.4
The prefix type of extremeOspfv3AreaAggregatePrefix. Only IPv6 addresses are expected.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddressType

extremeOspfv3AreaAggregatePrefix		1.3.6.1.4.1.1916.1.50.1.12.1.5
The IPv6 Prefix.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddress	Size(0..16)

extremeOspfv3AreaAggregatePrefixLength		1.3.6.1.4.1.1916.1.50.1.12.1.6
The length of the prefix (in bits). A prefix can not be shorter than 3 bits.
Status: current	Access: not-accessible
OBJECT-TYPE
	InetAddressPrefixLength	3..128

extremeOspfv3AreaAggregateStatus		1.3.6.1.4.1.1916.1.50.1.12.1.7
This variable controls the status of the entry The use of RowStatus is covered in more detail in [6].
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

extremeOspfv3AreaAggregateEffect		1.3.6.1.4.1.1916.1.50.1.12.1.8
Prefixes subsumed by ranges either trigger the advertisement of the indicated aggregate (advertiseMatching), or result in the prefix not being advertised at all outside the area.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	advertiseMatching(1), doNotAdvertiseMatching(2)

extremeOspfv3AreaAggregateRouteTag		1.3.6.1.4.1.1916.1.50.1.12.1.9
This tag is advertised only in the summarized As-External LSA when summarizing from NSSA-LSA's to AS-External-LSA's.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32

extremeOspfv3NotificationEntry		1.3.6.1.4.1.1916.1.50.1.13
OBJECT IDENTIFIER

extremeOspfv3ConfigErrorType		1.3.6.1.4.1.1916.1.50.1.13.1
Potential types of configuration conflicts. Used by the extremeOspfv3ConfigError and extremeOspfv3ConfigVirtError notifications.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	INTEGER	badVersion(1), areaMismatch(2), unknownNbmaNbr(3), unknownVirtualNbr(4), helloIntervalMismatch(5), deadIntervalMismatch(6), optionMismatch(7), mtuMismatch(8), duplicateRouterId(9), noError(10)

extremeOspfv3PacketType		1.3.6.1.4.1.1916.1.50.1.13.2
OSPFv3 packet types.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	INTEGER	hello(1), dbDescript(2), lsReq(3), lsUpdate(4), lsAck(5), nullPacket(6)

extremeOspfv3PacketSrc		1.3.6.1.4.1.1916.1.50.1.13.3
The IPv6 address of an inbound packet that cannot be identified by a neighbor instance. Only IPv6 addresses without zone index are expected.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	InetAddressIPv6

extremeOspfv3VirtIfStateChange		1.3.6.1.4.1.1916.1.50.0.1
An extremeOspfv3VirtIfStateChange notification signifies that there has been a change in the state of an OSPFv3 virtual interface. This notification should be generated when the interface state regresses (e.g., goes from Point-to-Point to Down) or progresses to a terminal state (i.e., Point-to-Point).
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

extremeOspfv3NbrStateChange		1.3.6.1.4.1.1916.1.50.0.2
An extremeOspfv3NbrStateChange notification signifies that there has been a change in the state of a non-virtual OSPFv3 neighbor. This notification should be generated when the neighbor state regresses (e.g., goes from Attempt or Full to 1-Way or Down) or progresses to a terminal state (e.g., 2-Way or Full). When a neighbor transitions from or to Full on non-broadcast multi-access and broadcast networks, the notification should be generated by the Designated Router. A Designated Router transitioning to Down will be noted by ospfIfStateChange.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

extremeOspfv3VirtNbrStateChange		1.3.6.1.4.1.1916.1.50.0.3
An extremeOspfv3VirtNbrStateChange notification signifies that there has been a change in the state of an OSPFv3 virtual neighbor. This notification should be generated when the neighbor state regresses (e.g., goes from Attempt or Full to 1-Way or Down) or progresses to a terminal state (e.g., Full).
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

extremeOspfv3IfConfigError		1.3.6.1.4.1.1916.1.50.0.4
An extremeOspfv3IfConfigError notification signifies that a packet has been received on a non-virtual interface from a router whose configuration parameters conflict with this router's configuration parameters. Note that the event optionMismatch should cause a notification only if it prevents an adjacency from forming.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

extremeOspfv3VirtIfConfigError		1.3.6.1.4.1.1916.1.50.0.5
An extremeOspfv3VirtIfConfigError notification signifies that a packet has been received on a virtual interface from a router whose configuration parameters conflict with this router's configuration parameters. Note that the event optionMismatch should cause a notification only if it prevents an adjacency from forming.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

extremeOspfv3IfStateChange		1.3.6.1.4.1.1916.1.50.0.6
An extremeOspfv3IfStateChange notification signifies that there has been a change in the state of a non-virtual OSPFv3 interface. This notification should be generated when the interface state regresses (e.g., goes from DR to Down) or progresses to a terminal state (i.e., Point-to-Point, DR Other, DR, or Backup).
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

extremeOspfv3NssaTranslatorStatusChange		1.3.6.1.4.1.1916.1.50.0.7
An extremeOspfv3NssaTranslatorStatusChange notification indicates that there has been a change in the router's ability to translate OSPFv3 NSSA LSAs into OSPFv3 External LSAs. This notification should be generated when the Translator Status transitions from or to any defined status on a per-area basis.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

extremeOspfv3NbrRestartHelperStatusChange		1.3.6.1.4.1.1916.1.50.0.8
An extremeOspfv3NbrRestartHelperStatusChange notification signifies that there has been a change in the graceful restart helper state for the neighbor. This notification should be generated when the neighbor restart helper status transitions for a neighbor.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

extremeOspfv3VirtNbrRestartHelperStatusChange		1.3.6.1.4.1.1916.1.50.0.9
An extremeOspfv3VirtNbrRestartHelperStatusChange notification signifies that there has been a change in the graceful restart helper state for the virtual neighbor. This notification should be generated when the virtual neighbor restart helper status transitions for a virtual neighbor.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

extremeOspfv3Groups		1.3.6.1.4.1.1916.1.50.2.1
OBJECT IDENTIFIER

extremeOspfv3Compliances		1.3.6.1.4.1.1916.1.50.2.2
OBJECT IDENTIFIER

extremeOspfv3Compliance		1.3.6.1.4.1.1916.1.50.2.2.1
The compliance statement
Status: current	Access: accessible-for-notify
MODULE-COMPLIANCE

extremeOspfv3BasicGroup		1.3.6.1.4.1.1916.1.50.2.1.1
These objects are required for OSPFv3 systems.
Status: current	Access: accessible-for-notify
OBJECT-GROUP

extremeOspfv3AreaGroup		1.3.6.1.4.1.1916.1.50.2.1.2
These objects are required for OSPFv3 systems supporting areas.
Status: current	Access: accessible-for-notify
OBJECT-GROUP

extremeOspfv3AsLsdbGroup		1.3.6.1.4.1.1916.1.50.2.1.3
These objects are required for OSPFv3 systems that display their AS-scope link state database.
Status: current	Access: accessible-for-notify
OBJECT-GROUP

extremeOspfv3AreaLsdbGroup		1.3.6.1.4.1.1916.1.50.2.1.4
These objects are required for OSPFv3 systems that display their Area-scope link state database.
Status: current	Access: accessible-for-notify
OBJECT-GROUP

extremeOspfv3LinkLsdbGroup		1.3.6.1.4.1.1916.1.50.2.1.5
These objects are required for OSPFv3 systems that display their Link-scope link state database.
Status: current	Access: accessible-for-notify
OBJECT-GROUP

extremeOspfv3HostGroup		1.3.6.1.4.1.1916.1.50.2.1.6
These objects are required for OSPFv3 systems that support attached hosts.
Status: current	Access: accessible-for-notify
OBJECT-GROUP

extremeOspfv3IfGroup		1.3.6.1.4.1.1916.1.50.2.1.7
These interface objects are required for OSPFv3 systems.
Status: current	Access: accessible-for-notify
OBJECT-GROUP

extremeOspfv3VirtIfGroup		1.3.6.1.4.1.1916.1.50.2.1.8
These virtual interface objects are required for OSPFv3 systems.
Status: current	Access: accessible-for-notify
OBJECT-GROUP

extremeOspfv3NbrGroup		1.3.6.1.4.1.1916.1.50.2.1.9
These neighbor objects are required for OSPFv3 systems.
Status: current	Access: accessible-for-notify
OBJECT-GROUP

extremeOspfv3CfgNbrGroup		1.3.6.1.4.1.1916.1.50.2.1.10
These Configured neighbor objects are required for OSPFv3 systems.
Status: current	Access: accessible-for-notify
OBJECT-GROUP

extremeOspfv3VirtNbrGroup		1.3.6.1.4.1.1916.1.50.2.1.11
These virtual neighbor objects are required for OSPFv3 systems.
Status: current	Access: accessible-for-notify
OBJECT-GROUP

extremeOspfv3AreaAggregateGroup		1.3.6.1.4.1.1916.1.50.2.1.12
These area aggregate objects are required for OSPFv3 systems.
Status: current	Access: accessible-for-notify
OBJECT-GROUP

extremeOspfv3NotificationObjectGroup		1.3.6.1.4.1.1916.1.50.2.1.13
These objects are used to record notification parameters.
Status: current	Access: accessible-for-notify
OBJECT-GROUP

extremeOspfv3NotificationGroup		1.3.6.1.4.1.1916.1.50.2.1.14
This group is used for OSPFv3 notifications.
Status: current	Access: accessible-for-notify
NOTIFICATION-GROUP