EMD-MIB

File: EMD-MIB.mib (116513 bytes)

Imported modules

SNMPv2-SMI	SNMPv2-CONF	SNMPv2-TC
INET-ADDRESS-MIB	RFC1213-MIB

Imported symbols

MODULE-IDENTITY	OBJECT-TYPE	NOTIFICATION-TYPE
enterprises	Integer32	Unsigned32
MODULE-COMPLIANCE	OBJECT-GROUP	NOTIFICATION-GROUP
TEXTUAL-CONVENTION	DisplayString	MacAddress
TruthValue	InetAddressType	InetAddress
InetPortNumber	sysContact	sysName
sysLocation

Defined Types

SensorTypeEnumeration
The types a sensor can be.
TEXTUAL-CONVENTION
	INTEGER	rmsCurrent(1), peakCurrent(2), unbalancedCurrent(3), rmsVoltage(4), activePower(5), apparentPower(6), powerFactor(7), activeEnergy(8), apparentEnergy(9), temperature(10), humidity(11), airFlow(12), airPressure(13), onOff(14), trip(15), vibration(16), waterDetection(17), smokeDetection(18), binary(19), contact(20), fanSpeed(21), absoluteHumidity(28), other(30), none(31), illuminance(42), doorContact(43), tamperDetection(44), motionDetection(45)

SensorStateEnumeration
The states a sensor can be in.
TEXTUAL-CONVENTION
	INTEGER	unavailable(-1), open(0), closed(1), belowLowerCritical(2), belowLowerWarning(3), normal(4), aboveUpperWarning(5), aboveUpperCritical(6), on(7), off(8), detected(9), notDetected(10), alarmed(11)

SensorUnitsEnumeration
The types a sensor can be.
TEXTUAL-CONVENTION
	INTEGER	none(-1), other(0), volt(1), amp(2), watt(3), voltamp(4), wattHour(5), voltampHour(6), degreeC(7), hertz(8), percent(9), meterpersec(10), pascal(11), psi(12), g(13), degreeF(14), feet(15), inches(16), cm(17), meters(18), rpm(19), degrees(20), lux(21), grampercubicmeter(22), voltampReactive(23)

ExternalSensorsZCoordinateUnitsEnumeration
The units of the external Sensor Z Coordinate. rackUnits implies that the Z Coordinate for all external sensors is in rack Units (U) text implies that the Z Coordinate for all external sensors is a text string (label)
TEXTUAL-CONVENTION
	INTEGER	rackUnits(0), text(1)

HundredthsOfAPercentage
Data type for reporting values in hundredths of percentage, i.e. 0.01 %.
TEXTUAL-CONVENTION
	Unsigned32	0..10000

DeviceIdentificationParameterEnumeration
The configurable parameters.
TEXTUAL-CONVENTION
	INTEGER	deviceName(0), sysContact(1), sysName(2), sysLocation(3)

PeripheralDeviceFirmwareUpdateStateEnumeration
The state of an peripheral device firmware update.
TEXTUAL-CONVENTION
	INTEGER	started(1), successful(2), failed(3)

ExternalSensorConfigurationEntryStruct
SEQUENCE
	sensorID	Integer32
	externalSensorType	SensorTypeEnumeration
	externalSensorSerialNumber	DisplayString
	externalSensorName	DisplayString
	externalSensorDescription	DisplayString
	externalSensorXCoordinate	DisplayString
	externalSensorYCoordinate	DisplayString
	externalSensorZCoordinate	DisplayString
	externalSensorChannelNumber	Integer32
	externalOnOffSensorSubtype	SensorTypeEnumeration
	externalSensorUnits	SensorUnitsEnumeration
	externalSensorDecimalDigits	Unsigned32
	externalSensorAccuracy	HundredthsOfAPercentage
	externalSensorResolution	Unsigned32
	externalSensorTolerance	Unsigned32
	externalSensorMaximum	Integer32
	externalSensorMinimum	Integer32
	externalSensorHysteresis	Unsigned32
	externalSensorStateChangeDelay	Unsigned32
	externalSensorLowerCriticalThreshold	Integer32
	externalSensorLowerWarningThreshold	Integer32
	externalSensorUpperCriticalThreshold	Integer32
	externalSensorUpperWarningThreshold	Integer32
	externalSensorEnabledThresholds	BITS
	externalSensorPort	DisplayString
	externalSensorIsActuator	TruthValue
	externalSensorAlarmedToNormalDelay	Integer32
	externalSensorUseDefaultThresholds	TruthValue

ExternalSensorTypeDefaultThresholdsEntryStruct
SEQUENCE
	externalSensorTypeDefaultHysteresis	Unsigned32
	externalSensorTypeDefaultStateChangeDelay	Unsigned32
	externalSensorTypeDefaultLowerCriticalThreshold	Integer32
	externalSensorTypeDefaultLowerWarningThreshold	Integer32
	externalSensorTypeDefaultUpperCriticalThreshold	Integer32
	externalSensorTypeDefaultUpperWarningThreshold	Integer32
	externalSensorTypeDefaultEnabledThresholds	BITS

PeripheralDevicePackageEntryStruct
SEQUENCE
	peripheralDevicePackageId	Integer32
	peripheralDevicePackageSerialNumber	DisplayString
	peripheralDevicePackageModel	DisplayString
	peripheralDevicePackageFirmwareVersion	DisplayString
	peripheralDevicePackageMinFirmwareVersion	DisplayString
	peripheralDevicePackageFirmwareTimeStamp	Unsigned32
	peripheralDevicePackagePosition	DisplayString
	peripheralDevicePackageState	DisplayString

ServerReachabilityEntryStruct
SEQUENCE
	serverID	Integer32
	serverIPAddress	DisplayString
	serverPingEnabled	TruthValue

LogTimeStampEntryStruct
SEQUENCE
	logIndex	Integer32
	logTimeStamp	Unsigned32

ExternalSensorLogEntryStruct
SEQUENCE
	logExternalSensorDataAvailable	TruthValue
	logExternalSensorState	SensorStateEnumeration
	logExternalSensorAvgValue	Integer32
	logExternalSensorMaxValue	Integer32
	logExternalSensorMinValue	Integer32

ExternalSensorMeasurementsEntryStruct
SEQUENCE
	measurementsExternalSensorIsAvailable	TruthValue
	measurementsExternalSensorState	SensorStateEnumeration
	measurementsExternalSensorValue	Integer32
	measurementsExternalSensorTimeStamp	Unsigned32

ActuatorControlEntryStruct
SEQUENCE
	actuatorState	SensorStateEnumeration

Defined Values

raritan		1.3.6.1.4.1.13742
This MIB describes the SNMP functions of the EMX Environmental Monitoring Device by Raritan Computer.
MODULE-IDENTITY

emd		1.3.6.1.4.1.13742.8
OBJECT IDENTIFIER

traps		1.3.6.1.4.1.13742.8.0
OBJECT IDENTIFIER

trapInformation		1.3.6.1.4.1.13742.8.0.0
OBJECT IDENTIFIER

configuration		1.3.6.1.4.1.13742.8.1
OBJECT IDENTIFIER

measurements		1.3.6.1.4.1.13742.8.2
OBJECT IDENTIFIER

conformance		1.3.6.1.4.1.13742.8.3
OBJECT IDENTIFIER

log		1.3.6.1.4.1.13742.8.4
OBJECT IDENTIFIER

control		1.3.6.1.4.1.13742.8.5
OBJECT IDENTIFIER

unit		1.3.6.1.4.1.13742.8.1.1
OBJECT IDENTIFIER

externalSensors		1.3.6.1.4.1.13742.8.1.2
OBJECT IDENTIFIER

serverReachability		1.3.6.1.4.1.13742.8.1.3
OBJECT IDENTIFIER

measurementsExternalSensor		1.3.6.1.4.1.13742.8.2.1
OBJECT IDENTIFIER

compliances		1.3.6.1.4.1.13742.8.3.1
OBJECT IDENTIFIER

groups		1.3.6.1.4.1.13742.8.3.2
OBJECT IDENTIFIER

logUnit		1.3.6.1.4.1.13742.8.4.1
OBJECT IDENTIFIER

logExternalSensor		1.3.6.1.4.1.13742.8.4.2
OBJECT IDENTIFIER

actuatorControl		1.3.6.1.4.1.13742.8.5.1
OBJECT IDENTIFIER

complianceRev1		1.3.6.1.4.1.13742.8.3.1.1
The requirements for conformance to the EMD-MIB.
Status: current	Access: read-only
MODULE-COMPLIANCE

configGroup		1.3.6.1.4.1.13742.8.3.2.1
A collection of objects representing configuration data.
Status: current	Access: read-only
OBJECT-GROUP

measurementsGroup		1.3.6.1.4.1.13742.8.3.2.2
A collection of objects providing the measurement capability of EMD.
Status: current	Access: read-only
OBJECT-GROUP

trapInformationGroup		1.3.6.1.4.1.13742.8.3.2.3
A collection of objects providing information in the traps.
Status: current	Access: read-only
OBJECT-GROUP

trapsGroup		1.3.6.1.4.1.13742.8.3.2.4
A collection of traps.
Status: current	Access: read-only
NOTIFICATION-GROUP

logGroup		1.3.6.1.4.1.13742.8.3.2.5
A collection of objects providing the logging capabilities about the EMD.
Status: current	Access: read-only
OBJECT-GROUP

controlGroup		1.3.6.1.4.1.13742.8.3.2.6
A collection of objects providing the ability to control actuators of the EMD.
Status: current	Access: read-only
OBJECT-GROUP

unitConfiguration		1.3.6.1.4.1.13742.8.1.1.1
OBJECT IDENTIFIER

deviceName		1.3.6.1.4.1.13742.8.1.1.1.1
The user-defined name for the EMD.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

hardwareVersion		1.3.6.1.4.1.13742.8.1.1.1.2
The main boards hardware version.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

firmwareVersion		1.3.6.1.4.1.13742.8.1.1.1.3
The firmware version.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

utcOffset		1.3.6.1.4.1.13742.8.1.1.1.4
The current UTC offset.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

externalSensorCount		1.3.6.1.4.1.13742.8.1.1.1.5
The number of external sensors.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..255

managedExternalSensorCount		1.3.6.1.4.1.13742.8.1.1.1.6
The number of managed external sensors
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..255

externalSensorsZCoordinateUnits		1.3.6.1.4.1.13742.8.1.1.1.7
External Sensor Z Coordinate units: Freeform Text or Rack Units (U). Default is U.
Status: current	Access: read-write
OBJECT-TYPE
	ExternalSensorsZCoordinateUnitsEnumeration

deviceMACAddress		1.3.6.1.4.1.13742.8.1.1.1.8
The current MAC address.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

deviceInetAddressType		1.3.6.1.4.1.13742.8.1.1.1.9
The type of address format
Status: current	Access: read-only
OBJECT-TYPE
	InetAddressType

deviceInetIPAddress		1.3.6.1.4.1.13742.8.1.1.1.10
The current IP address. A value of 0.0.0.0 indicates an error or an unset option.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddress

deviceInetNetmask		1.3.6.1.4.1.13742.8.1.1.1.11
The current netmask. A value of 0.0.0.0 indicates an error or an unset option.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddress

deviceInetGateway		1.3.6.1.4.1.13742.8.1.1.1.12
The current gateway. A value of 0.0.0.0 indicates an error or an unset option.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddress

serverCount		1.3.6.1.4.1.13742.8.1.1.1.13
The number of entries in serverReachabilityTable
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..255

model		1.3.6.1.4.1.13742.8.1.1.1.14
The EMD device model.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

cascadedDeviceConnected		1.3.6.1.4.1.13742.8.1.1.1.15
Indicates whether a device is connected using an USB cable to the USB-A port of this EMX in a cascaded configuration. true: Connected false: Not Connected
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

peripheralDevicesAutoManagement		1.3.6.1.4.1.13742.8.1.1.1.16
Set enabled state of auto management for new peripheral devices.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

synchronizeWithNTPServer		1.3.6.1.4.1.13742.8.1.1.1.17
Set enabled state of the device's NTP client.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

useDHCPProvidedNTPServer		1.3.6.1.4.1.13742.8.1.1.1.18
Enable usage of the DHCP/BOOTP provided NTP server addresses; the value is used only if synchronizeWithNTPServer is enabled.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

firstNTPServerAddressType		1.3.6.1.4.1.13742.8.1.1.1.19
Represents the type of firstNTPServerAddress.
Status: current	Access: read-write
OBJECT-TYPE
	InetAddressType

firstNTPServerAddress		1.3.6.1.4.1.13742.8.1.1.1.20
The address of the primary NTP server.
Status: current	Access: read-write
OBJECT-TYPE
	InetAddress

secondNTPServerAddressType		1.3.6.1.4.1.13742.8.1.1.1.21
Represents the type of secondNTPServerAddress.
Status: current	Access: read-write
OBJECT-TYPE
	InetAddressType

secondNTPServerAddress		1.3.6.1.4.1.13742.8.1.1.1.22
The address of the secondary NTP server.
Status: current	Access: read-write
OBJECT-TYPE
	InetAddress

logConfiguration		1.3.6.1.4.1.13742.8.1.1.2
OBJECT IDENTIFIER

dataLogging		1.3.6.1.4.1.13742.8.1.1.2.1
Data Retrieval: enabled/disabled.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

measurementPeriod		1.3.6.1.4.1.13742.8.1.1.2.2
Data Collection periodicity. This is the periodicity of the data collected by the PX. This value is fixed at 1 second.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

measurementsPerLogEntry		1.3.6.1.4.1.13742.8.1.1.2.3
The number of measurements used for each entry in the log.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

logSize		1.3.6.1.4.1.13742.8.1.1.2.4
The number of entries in the log.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

dataLoggingEnableForAllSensors		1.3.6.1.4.1.13742.8.1.1.2.5
Operation to control data logging for all sensors. If this OID is set to true, then all xxxSensorLogAvailable are set to true If this OID is set to false, then all xxxSensorLogAvailable are set to false
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

externalSensorConfigurationTable		1.3.6.1.4.1.13742.8.1.2.1
A list of externalSensor configuration entries. The number of entries is given by the value of externalSensorCount for the EMD.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ExternalSensorConfigurationEntryStruct

externalSensorConfigurationEntry		1.3.6.1.4.1.13742.8.1.2.1.1
An entry containing parameters for an external sensor.
Status: current	Access: not-accessible
OBJECT-TYPE
	ExternalSensorConfigurationEntryStruct

sensorID		1.3.6.1.4.1.13742.8.1.2.1.1.1
A unique value for each sensor. Its value ranges between 1 and the value of externalSensorCount.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..256

externalSensorType		1.3.6.1.4.1.13742.8.1.2.1.1.2
The type of sensor.
Status: current	Access: read-only
OBJECT-TYPE
	SensorTypeEnumeration

externalSensorSerialNumber		1.3.6.1.4.1.13742.8.1.2.1.1.3
The sensor serial number.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

externalSensorName		1.3.6.1.4.1.13742.8.1.2.1.1.4
The user-defined name.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

externalSensorDescription		1.3.6.1.4.1.13742.8.1.2.1.1.5
The user-defined description.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

externalSensorXCoordinate		1.3.6.1.4.1.13742.8.1.2.1.1.6
The X coordinate.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

externalSensorYCoordinate		1.3.6.1.4.1.13742.8.1.2.1.1.7
The Y coordinate.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

externalSensorZCoordinate		1.3.6.1.4.1.13742.8.1.2.1.1.8
The Z coordinate.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

externalSensorChannelNumber		1.3.6.1.4.1.13742.8.1.2.1.1.9
The channel number, applies only to contact sensors; -1 for other sensors
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

externalOnOffSensorSubtype		1.3.6.1.4.1.13742.8.1.2.1.1.10
Type of measurement in case sensor type is discrete OnOff
Status: current	Access: read-write
OBJECT-TYPE
	SensorTypeEnumeration

externalSensorUnits		1.3.6.1.4.1.13742.8.1.2.1.1.11
The base units. This parameter does not apply to onOff, trip, vibration, waterDetection, smokeDetection sensors.
Status: current	Access: read-only
OBJECT-TYPE
	SensorUnitsEnumeration

externalSensorDecimalDigits		1.3.6.1.4.1.13742.8.1.2.1.1.12
The number of digits displayed to the right of the decimal point This parameter does not apply to onOff, trip, vibration, waterDetection, smokeDetection sensors.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

externalSensorAccuracy		1.3.6.1.4.1.13742.8.1.2.1.1.13
The accuracy: how close (in percent) the measurement is to the actual value. This parameter does not apply to onOff, trip, vibration, waterDetection, smokeDetection sensors.
Status: current	Access: read-only
OBJECT-TYPE
	HundredthsOfAPercentage

externalSensorResolution		1.3.6.1.4.1.13742.8.1.2.1.1.14
The resolution: the minimum difference between any two measured values. The value of this OID variable should be scaled by externalSensorDecimalDigits. For example, if the value is 1 and externalSensorDecimalDigits is 2, then actual value is 0.01. This parameter does not apply to onOff, trip, vibration, waterDetection, smokeDetection sensors.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

externalSensorTolerance		1.3.6.1.4.1.13742.8.1.2.1.1.15
The resolution: the difference between a sensor value and the actual value. The value of this OID variable should be scaled by (externalSensorDecimalDigits + 1). For example, if the value is 50 and externalSensorDecimalDigits is 2, then actual value is 0.05. This parameter does not apply to onOff, trip, vibration, waterDetection, smokeDetection sensors.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

externalSensorMaximum		1.3.6.1.4.1.13742.8.1.2.1.1.16
The largest possible value The value of this OID variable should be scaled by externalSensorDecimalDigits. For example, if the value is 1 and externalSensorDecimalDigits is 2, then actual value is 0.01. This parameter does not apply to onOff, trip, vibration, waterDetection, smokeDetection sensors.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

externalSensorMinimum		1.3.6.1.4.1.13742.8.1.2.1.1.17
The smallest possible value The value of this OID variable should be scaled by externalSensorDecimalDigits. For example, if the value is 1 and externalSensorDecimalDigits is 2, then actual value is 0.01. This parameter does not apply to onOff, trip, vibration, waterDetection, smokeDetection sensors.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

externalSensorHysteresis		1.3.6.1.4.1.13742.8.1.2.1.1.18
The hysteresis used for deassertions The value of this OID variable should be scaled by externalSensorDecimalDigits. For example, if the value is 1 and externalSensorDecimalDigits is 2, then actual value is 0.01. This parameter does not apply to onOff, trip, vibration, waterDetection, smokeDetection sensors.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

externalSensorStateChangeDelay		1.3.6.1.4.1.13742.8.1.2.1.1.19
The delay measured in samples before a state is asserted. If the value is zero, then the state is asserted as soon as it is detected; if it is non-zero, say n, then the assertion condition must exist for n+1 consecutive samples before the corresponding assertion event is reported. At present, this value cannot be written (set)
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

externalSensorLowerCriticalThreshold		1.3.6.1.4.1.13742.8.1.2.1.1.20
The lower critical threshold The value of this OID variable should be scaled by externalSensorDecimalDigits. For example, if the value is 1 and externalSensorDecimalDigits is 2, then actual value is 0.01. This parameter does not apply to onOff, trip, vibration, waterDetection, smokeDetection sensors.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

externalSensorLowerWarningThreshold		1.3.6.1.4.1.13742.8.1.2.1.1.21
The lower non-critical (warning) threshold The value of this OID variable should be scaled by externalSensorDecimalDigits. For example, if the value is 1 and externalSensorDecimalDigits is 2, then actual value is 0.01. This parameter does not apply to onOff, trip, vibration, waterDetection, smokeDetection sensors.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

externalSensorUpperCriticalThreshold		1.3.6.1.4.1.13742.8.1.2.1.1.22
The upper critical threshold The value of this OID variable should be scaled by externalSensorDecimalDigits. For example, if the value is 1 and externalSensorDecimalDigits is 2, then actual value is 0.01. This parameter does not apply to onOff, trip, vibration, waterDetection, smokeDetection sensors.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

externalSensorUpperWarningThreshold		1.3.6.1.4.1.13742.8.1.2.1.1.23
The upper non-critical (warning) threshold The value of this OID variable should be scaled by externalSensorDecimalDigits. For example, if the value is 1 and externalSensorDecimalDigits is 2, then actual value is 0.01. This parameter does not apply to onOff, trip, vibration, waterDetection, smokeDetection sensors.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

externalSensorEnabledThresholds		1.3.6.1.4.1.13742.8.1.2.1.1.24
A bit string which indicates which thresholds are enabled. This parameter does not apply to onOff, trip, vibration, waterDetection, smokeDetection sensors
Status: current	Access: read-write
OBJECT-TYPE
	BITS	lowerCritical(0), lowerWarning(1), upperWarning(2), upperCritical(3)

externalSensorPort		1.3.6.1.4.1.13742.8.1.2.1.1.25
The position of the sensor. The format is a semicolon separated list of Keyword:value pairs - Keyword1:Value1;Keyword2:value2;... Keyword can be one of the following: ONBOARD, DEVICE-1WIREPORT, HUBPORT, CHAIN-POSITION Examples 1) Onboard Sensor ONBOARD:CC1 2) Old sensor connected to device 1-wire port DEVICE-1WIREPORT:2 3) New style sensor connected to device 1-wire port DEVICE-1WIREPORT:2;CHAIN-POSITION:3 4) New style sensor connected to hub port 3 DEVICE-1WIREPORT:2;CHAIN-POSITION:1;HUBPORT:3;CHAIN-POSITION:1 5) Old style sensor connected to end of new style sensor chain DEVICE-1WIREPORT:2;
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

externalSensorIsActuator		1.3.6.1.4.1.13742.8.1.2.1.1.26
Is this an actuator? True: It is an actuator False: It is not an actuator
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

externalSensorAlarmedToNormalDelay		1.3.6.1.4.1.13742.8.1.2.1.1.27
The delay in seconds for transitions from the alarmed state to the normal state. If the sensor type is motionDetection, then it can set to a value greater >= 0 For all other sensor types, the value is 0 and cannot be set to any other value.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

externalSensorUseDefaultThresholds		1.3.6.1.4.1.13742.8.1.2.1.1.28
Use default thresholds for this sensor? True: Use default thresholds for this sensor False: Do not use default thresholds for this sensor
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

externalSensorTypeDefaultThresholdsTable		1.3.6.1.4.1.13742.8.1.2.4
A list of entries listing the default thresholds for each sensor type.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ExternalSensorTypeDefaultThresholdsEntryStruct

externalSensorTypeDefaultThresholdsEntry		1.3.6.1.4.1.13742.8.1.2.4.1
An entry containing default thresholds for a sensor type.
Status: current	Access: not-accessible
OBJECT-TYPE
	ExternalSensorTypeDefaultThresholdsEntryStruct

externalSensorTypeDefaultHysteresis		1.3.6.1.4.1.13742.8.1.2.4.1.3
The hysteresis used for deassertions The value of this OID variable should be scaled by externalSensorDecimalDigits. For example, if the value is 1 and externalSensorDecimalDigits is 2, then actual value is 0.01. This parameter does not apply to onOff, trip, vibration, waterDetection, smokeDetection sensors.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

externalSensorTypeDefaultStateChangeDelay		1.3.6.1.4.1.13742.8.1.2.4.1.4
The delay measured in samples before a state is asserted. If the value is zero, then the state is asserted as soon as it is detected; if it is non-zero, say n, then the assertion condition must exist for n+1 consecutive samples before the corresponding assertion event is reported. At present, this value cannot be written (set)
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

externalSensorTypeDefaultLowerCriticalThreshold		1.3.6.1.4.1.13742.8.1.2.4.1.5
The lower critical threshold The value of this OID variable should be scaled by externalSensorDecimalDigits. For example, if the value is 1 and externalSensorDecimalDigits is 2, then actual value is 0.01. This parameter does not apply to onOff, trip, vibration, waterDetection, smokeDetection sensors.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

externalSensorTypeDefaultLowerWarningThreshold		1.3.6.1.4.1.13742.8.1.2.4.1.6
The lower non-critical (warning) threshold The value of this OID variable should be scaled by externalSensorDecimalDigits. For example, if the value is 1 and externalSensorDecimalDigits is 2, then actual value is 0.01. This parameter does not apply to onOff, trip, vibration, waterDetection, smokeDetection sensors.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

externalSensorTypeDefaultUpperCriticalThreshold		1.3.6.1.4.1.13742.8.1.2.4.1.7
The upper critical threshold The value of this OID variable should be scaled by externalSensorDecimalDigits. For example, if the value is 1 and externalSensorDecimalDigits is 2, then actual value is 0.01. This parameter does not apply to onOff, trip, vibration, waterDetection, smokeDetection sensors.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

externalSensorTypeDefaultUpperWarningThreshold		1.3.6.1.4.1.13742.8.1.2.4.1.8
The upper non-critical (warning) threshold The value of this OID variable should be scaled by externalSensorDecimalDigits. For example, if the value is 1 and externalSensorDecimalDigits is 2, then actual value is 0.01. This parameter does not apply to onOff, trip, vibration, waterDetection, smokeDetection sensors.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

externalSensorTypeDefaultEnabledThresholds		1.3.6.1.4.1.13742.8.1.2.4.1.9
A bit string which indicates which thresholds are enabled. This parameter does not apply to onOff, trip, vibration, waterDetection, smokeDetection sensors
Status: current	Access: read-write
OBJECT-TYPE
	BITS	lowerCritical(0), lowerWarning(1), upperWarning(2), upperCritical(3)

peripheralDevicePackageTable		1.3.6.1.4.1.13742.8.1.2.5
A list of entries for the peripheral Device Packages connected to an EMX. The number of entries is given by the value of peripheralDevicePackagesCount.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PeripheralDevicePackageEntryStruct

peripheralDevicePackageEntry		1.3.6.1.4.1.13742.8.1.2.5.1
An entry containing objects for a controller.
Status: current	Access: not-accessible
OBJECT-TYPE
	PeripheralDevicePackageEntryStruct

peripheralDevicePackageId		1.3.6.1.4.1.13742.8.1.2.5.1.1
A unique value for each peripheral device package.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..256

peripheralDevicePackageSerialNumber		1.3.6.1.4.1.13742.8.1.2.5.1.3
The peripheral device package serial number.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

peripheralDevicePackageModel		1.3.6.1.4.1.13742.8.1.2.5.1.4
The peripheral device package model. Examples are DX-D2C6, DPX2-T1, DPX2-T1H1, DPX2-T2H1, DPX2-T3H1
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

peripheralDevicePackageFirmwareVersion		1.3.6.1.4.1.13742.8.1.2.5.1.5
The peripheral device package firmware version.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

peripheralDevicePackageMinFirmwareVersion		1.3.6.1.4.1.13742.8.1.2.5.1.6
The peripheral device package minimum firmware version. This field may be empty. If it is not empty, then it shall not be possible to downgrade the peripheral device firmware to a version < minimum firmware version number.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

peripheralDevicePackageFirmwareTimeStamp		1.3.6.1.4.1.13742.8.1.2.5.1.7
The time when the peripheralDevicePackage firmware was updated in UNIX(epoch)time. It is measured in seconds relative to January 1, 1970 (midnight UTC/GMT), i.e a value of 0 indicates January 1, 1970 (midnight UTC/GMT).
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

peripheralDevicePackagePosition		1.3.6.1.4.1.13742.8.1.2.5.1.8
The position of the package. The format is a semicolon separated list of Keyword:value pairs - Keyword1:Value1;Keyword2:value2;... Keyword can be one of the following: ONBOARD, DEVICE-1WIREPORT, HUBPORT, CHAIN-POSITION Examples 1) Onboard Sensor ONBOARD:CC1 2) Old sensor connected to device 1-wire port DEVICE-1WIREPORT:2 3) New style sensor connected to device 1-wire port DEVICE-1WIREPORT:2;CHAIN-POSITION:3 4) New style sensor connected to hub port 3 DEVICE-1WIREPORT:2;CHAIN-POSITION:1;HUBPORT:3;CHAIN-POSITION:1 5) Old style sensor connected to end of new style sensor chain DEVICE-1WIREPORT:2;
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

peripheralDevicePackageState		1.3.6.1.4.1.13742.8.1.2.5.1.9
The state of the package.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

serverReachabilityTable		1.3.6.1.4.1.13742.8.1.3.1
A list of server entries. The number of entries is given by the value of serverCount for the EMD.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ServerReachabilityEntryStruct

serverReachabilityEntry		1.3.6.1.4.1.13742.8.1.3.1.1
An entry containing parameters for a server.
Status: current	Access: not-accessible
OBJECT-TYPE
	ServerReachabilityEntryStruct

serverID		1.3.6.1.4.1.13742.8.1.3.1.1.1
A unique value for each server. Its value ranges between 1 and the value of serverCount for that EMD
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..256

serverIPAddress		1.3.6.1.4.1.13742.8.1.3.1.1.2
The IP Address/host name of the server
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

serverPingEnabled		1.3.6.1.4.1.13742.8.1.3.1.1.3
Is ping enabled for this server?
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

oldestLogID		1.3.6.1.4.1.13742.8.4.1.1
The index of the oldest data in the buffer for this EMD.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

newestLogID		1.3.6.1.4.1.13742.8.4.1.2
The index of the newest data in the buffer for this EMD.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

logTimeStampTable		1.3.6.1.4.1.13742.8.4.1.3
A list of entries containing the timestamps of the entries in the log.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LogTimeStampEntryStruct

logTimeStampEntry		1.3.6.1.4.1.13742.8.4.1.3.1
An entry containing the timestamp for log entries.
Status: current	Access: not-accessible
OBJECT-TYPE
	LogTimeStampEntryStruct

logIndex		1.3.6.1.4.1.13742.8.4.1.3.1.1
A unique value for each entry in the log. Its value ranges between 1 and the value of logSize.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..256

logTimeStamp		1.3.6.1.4.1.13742.8.4.1.3.1.2
The time when the data was collected. It is measured in seconds relative to January 1, 1970 (midnight UTC/GMT), i.e a value of 0 indicates January 1, 1970 (midnight UTC/GMT).
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

externalSensorLogTable		1.3.6.1.4.1.13742.8.4.2.1
A list of external sensor entries. The number of entries is given by the value of externalSensorCount for the EMD.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ExternalSensorLogEntryStruct

externalSensorLogEntry		1.3.6.1.4.1.13742.8.4.2.1.1
An entry containing log objects for an external sensor.
Status: current	Access: not-accessible
OBJECT-TYPE
	ExternalSensorLogEntryStruct

logExternalSensorDataAvailable		1.3.6.1.4.1.13742.8.4.2.1.1.2
Is data available for this sensor during this measurement period?
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

logExternalSensorState		1.3.6.1.4.1.13742.8.4.2.1.1.3
The sensor state.
Status: current	Access: read-only
OBJECT-TYPE
	SensorStateEnumeration

logExternalSensorAvgValue		1.3.6.1.4.1.13742.8.4.2.1.1.4
The sensor reading average value.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

logExternalSensorMaxValue		1.3.6.1.4.1.13742.8.4.2.1.1.5
The sensor reading maximum value.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

logExternalSensorMinValue		1.3.6.1.4.1.13742.8.4.2.1.1.6
The sensor reading minimum value.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

externalSensorMeasurementsTable		1.3.6.1.4.1.13742.8.2.1.1
A list of external sensor entries. The number of entries is given by the value of externalSensorCount for the EMD.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ExternalSensorMeasurementsEntryStruct

externalSensorMeasurementsEntry		1.3.6.1.4.1.13742.8.2.1.1.1
An entry containing measurement objects for an external sensor.
Status: current	Access: not-accessible
OBJECT-TYPE
	ExternalSensorMeasurementsEntryStruct

measurementsExternalSensorIsAvailable		1.3.6.1.4.1.13742.8.2.1.1.1.1
Is the sensor available?
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

measurementsExternalSensorState		1.3.6.1.4.1.13742.8.2.1.1.1.2
The sensor state.
Status: current	Access: read-only
OBJECT-TYPE
	SensorStateEnumeration

measurementsExternalSensorValue		1.3.6.1.4.1.13742.8.2.1.1.1.3
The sensor reading. This parameter does not apply to onOff, trip, vibration, waterDetection, smokeDetection sensors.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

measurementsExternalSensorTimeStamp		1.3.6.1.4.1.13742.8.2.1.1.1.4
The sensor reading timestamp.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

actuatorControlTable		1.3.6.1.4.1.13742.8.5.1.1
A list of actuators for an EMX.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ActuatorControlEntryStruct

actuatorControlEntry		1.3.6.1.4.1.13742.8.5.1.1.1
An entry for implementing user-initiated state changes for an actuator.
Status: current	Access: not-accessible
OBJECT-TYPE
	ActuatorControlEntryStruct

actuatorState		1.3.6.1.4.1.13742.8.5.1.1.1.1
The actuator state. A Get operation retrieves the state of the actuator. A Set operation changes the stae of the sensor. The valid states for set operations are on and Off. Attempting to set the state to any other value will generate an error.
Status: current	Access: read-write
OBJECT-TYPE
	SensorStateEnumeration

userName		1.3.6.1.4.1.13742.8.0.0.1
The user currently logged in.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

targetUser		1.3.6.1.4.1.13742.8.0.0.2
The user added, deleted, or modified.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

imageVersion		1.3.6.1.4.1.13742.8.0.0.3
The version of the upgrade image.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

roleName		1.3.6.1.4.1.13742.8.0.0.4
The role added, deleted, or modified.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

smtpMessageRecipients		1.3.6.1.4.1.13742.8.0.0.5
Comma separated list of SMTP Message recipients
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

smtpServer		1.3.6.1.4.1.13742.8.0.0.6
The IP address/host name of the SMTP server
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

oldSensorState		1.3.6.1.4.1.13742.8.0.0.7
The old sensor state used in Sensor State Transition traps.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	SensorStateEnumeration

externalSensorNumber		1.3.6.1.4.1.13742.8.0.0.8
A unique value for each sensor. Its value ranges between 1 and the value of externalSensorCount.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32	1..256

typeOfSensor		1.3.6.1.4.1.13742.8.0.0.9
The type of sensor.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	SensorTypeEnumeration

errorDescription		1.3.6.1.4.1.13742.8.0.0.10
Description of the Error
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString

deviceChangedParameter		1.3.6.1.4.1.13742.8.0.0.11
Description of the parameter(s) that changed.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DeviceIdentificationParameterEnumeration

changedParameterNewValue		1.3.6.1.4.1.13742.8.0.0.12
The new value of the changed parameter
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString

lhxSupportEnabled		1.3.6.1.4.1.13742.8.0.0.13
The new enabled state for Schroff LHX Support.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	TruthValue

webcamModel		1.3.6.1.4.1.13742.8.0.0.14
The model of the Webcam
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString

webcamConnectionPort		1.3.6.1.4.1.13742.8.0.0.15
The port to which the Webcam is connected
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString

peripheralDeviceRomcode		1.3.6.1.4.1.13742.8.0.0.16
The Romcode of an peripheral device
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString

peripheralDeviceFirmwareUpdateState		1.3.6.1.4.1.13742.8.0.0.17
The firmware update state of an peripheral device
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	PeripheralDeviceFirmwareUpdateStateEnumeration

agentInetPortNumber		1.3.6.1.4.1.13742.8.0.0.18
The UDP port number used for accessing the SNMP agent on the device. Examples: If deviceCascadeType is portForwarding, then master: 50500 slave 1:50501 slave 2: 50502 ...... If cascading mode is not portForwarding and default (Standard) ports are being used, then port: 161
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	InetPortNumber

phoneNumber		1.3.6.1.4.1.13742.8.0.0.19
The phone number of e.g. an SMS receiver.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString

systemStarted		1.3.6.1.4.1.13742.8.0.1
The system has started.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

systemReset		1.3.6.1.4.1.13742.8.0.2
The system was reset. The conditions under which this trap is sent include, but are not limited to, the following. using the GUI - Maintenance->Reset Unit using the CLI - reset emd unit
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

userLogin		1.3.6.1.4.1.13742.8.0.3
A user logged in.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

userLogout		1.3.6.1.4.1.13742.8.0.4
A user logged out.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

userAuthenticationFailure		1.3.6.1.4.1.13742.8.0.5
A user authentication attempt failed.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

userSessionTimeout		1.3.6.1.4.1.13742.8.0.6
A user timed out from the device.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

userAdded		1.3.6.1.4.1.13742.8.0.7
A user was added to the system.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

userModified		1.3.6.1.4.1.13742.8.0.8
A user account was modified.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

userDeleted		1.3.6.1.4.1.13742.8.0.9
A user was deleted from the system.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

roleAdded		1.3.6.1.4.1.13742.8.0.10
A role was added to the system.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

roleModified		1.3.6.1.4.1.13742.8.0.11
A role was modified.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

roleDeleted		1.3.6.1.4.1.13742.8.0.12
A role was deleted from the system.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

deviceUpdateStarted		1.3.6.1.4.1.13742.8.0.13
The device update has started.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

deviceUpdateCompleted		1.3.6.1.4.1.13742.8.0.14
The device update has completed.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

userBlocked		1.3.6.1.4.1.13742.8.0.15
A blocked user tried to log in.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

userPasswordChanged		1.3.6.1.4.1.13742.8.0.16
User password was changed.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

passwordSettingsChanged		1.3.6.1.4.1.13742.8.0.17
Strong password settings changed.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

firmwareValidationFailed		1.3.6.1.4.1.13742.8.0.18
Firmware validation failed.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

logFileCleared		1.3.6.1.4.1.13742.8.0.19
The log file has been cleared.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

bulkConfigurationSaved		1.3.6.1.4.1.13742.8.0.20
Bulk Configuration saved.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

bulkConfigurationCopied		1.3.6.1.4.1.13742.8.0.21
Bulk Configuration saved.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

externalSensorStateChange		1.3.6.1.4.1.13742.8.0.22
External Sensor State Change.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

smtpMessageTransmissionFailure		1.3.6.1.4.1.13742.8.0.23
SMTP message transmission failure
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

ldapError		1.3.6.1.4.1.13742.8.0.24
LDAP Error occurred; errorDescription describes the error
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

deviceUpdateFailed		1.3.6.1.4.1.13742.8.0.25
The device update has failed.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

pingServerEnabled		1.3.6.1.4.1.13742.8.0.26
The ping feature has been enabled
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

pingServerDisabled		1.3.6.1.4.1.13742.8.0.27
The ping feature has been disabled
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

serverNotReachable		1.3.6.1.4.1.13742.8.0.28
The server is not reachable
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

serverReachable		1.3.6.1.4.1.13742.8.0.29
The server is reachable
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

deviceIdentificationChanged		1.3.6.1.4.1.13742.8.0.30
Device identification has changed
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

usbSlaveConnected		1.3.6.1.4.1.13742.8.0.31
USB Connectivity to slave has been established
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

usbSlaveDisconnected		1.3.6.1.4.1.13742.8.0.32
USB Connectivity to slave has been lost
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

lhxSupportChanged		1.3.6.1.4.1.13742.8.0.33
The Schroff LHX Support changed to state 'lhxSupportEnabled'.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

userAcceptedRestrictedServiceAgreement		1.3.6.1.4.1.13742.8.0.34
The user accepted the Restricted Service Agreement.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

userDeclinedRestrictedServiceAgreement		1.3.6.1.4.1.13742.8.0.35
The user declined the Restricted Service Agreement.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

deviceSettingsSaved		1.3.6.1.4.1.13742.8.0.36
Device Settings have been saved.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

deviceSettingsRestored		1.3.6.1.4.1.13742.8.0.37
Device Settings have been restored.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

webcamInserted		1.3.6.1.4.1.13742.8.0.38
A webcam has been inserted
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

webcamRemoved		1.3.6.1.4.1.13742.8.0.39
A webcam has been removed
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

serverConnectivityUnrecoverable		1.3.6.1.4.1.13742.8.0.40
The connection to the server could not be recovered
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

radiusError		1.3.6.1.4.1.13742.8.0.41
LDAP Error occurred; errorDescription describes the error
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

serverReachabilityError		1.3.6.1.4.1.13742.8.0.42
Server Reachability Error occurred; errorDescription describes the error. This trap is sent when the Error state is entered. Reasons for transitioning to the Error state include the following: Unable to resolve the server hostname.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

unknownPeripheralDeviceAttached		1.3.6.1.4.1.13742.8.0.43
An unknown peripheral device was attached.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

peripheralDeviceFirmwareUpdate		1.3.6.1.4.1.13742.8.0.44
The firmware update state of a peripheral device changed while performing update to peripheralDevicePackageFirmwareVersion.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

smsMessageTransmissionFailure		1.3.6.1.4.1.13742.8.0.45
Sending an SMS message failed.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE